User Manual for KALED55XX1ZA

User Manual for KALED55XX1ZA
<>ϱϱyyϭ
USER MANUAL
Important Safety Instructions and Maintenance
Important Safety Instructions
CAUTION
Risk of electronic shock, do not open.
Do not attempt to service this product yourself
as opening or removing covers may expose
you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
High Voltage
Do not open
If the following problems occur:
Turn off the TV set and unplug the AC power cord
immediately if any of the following problems occur.
Ask your dealer or service centre to have it checked
by qualified service personnel
When:
- AC power cord is damaged.
- Poor fitting of AC power outlet.
- TV set is damaged by being dropped, hit or having something thrown at it.
- Any liquid or solid object falls through openings in the cabinet.
To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
The apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
The screen and cabinet get warm when the TV
is in use. This is not a malfunction.In case of
smoke, strange noise or strange smell from the
unit:
· Turn off the power switch immediately;
· Disconnect the power plug from the power
outlet;
· Contact your dealer or service centre. Never attempt to make repairs
yourself because this could be dangerous.
Never push objects of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short-circuit parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the set. Use special caution
in households where children are present. The apparatus is not suitable for children
under 3-year to operate.
Do not overload wall outlets, extension cords or
adaptors beyond their capacity, this can result in
fire or electrical shock.
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plug end, adaptors
and the point where they exit from the appliance. The mains plug is used as the
disconnect device. It shall remain readily accessible and should not be obstructed
during intended use. Make sure to plug the power cord in until it is firmly inserted.
When removing the power cord, make sure to hold the power plug when pulling the
plug from the outlet, do not pull the plug out by the wire. NEVER touch the plug or
power cord with wet hands. To disconnect the apparatus from the mains power, the
plug must be pulled out from the mains socket, therefore make sure the mains plug
is always easily accessible.
1
Important Safety Instructions and Maintenance
Important Safety Instructions
Do not push or scratch the front filter, or place any objects on top of the TV set. The
image may be uneven or the screen may be damaged.
To avoid the fire, no naked flame source,
such as lighted candles, should be placed on the
apparatus.
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.Ensuring the television is not
overhanging the edge of the supporting furniture.
When not in use
If you will not be using the TV set for several days, the
TV set should be disconnected from the AC mains for
environmental and safety reasons. As the TV set is not
disconnected from the AC power when the TV is turned
off at the standby switch, pull the plug from the AC power
outlet to disconnect the TV completely. However, some
TV sets may have features that require the TV set to be
left in standby to function correctly. In the case of lightning,
unplug the TV set from the outlet immediately. Never
touch the antenna wire during lightning.
Do not pull the plug out by the wire;
Never touch the plug with wet hands.
Excessive volume from earphones and headphones
can cause hearing loss.
Installation
The ventilation should not be impeded by covering the
ventilation opening with items, such as newspapers,
tablecloths, curtains, etc.
At least 10 cm space should be left around the
apparatus for sufficient ventilation.
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
Place the apparatus in such a position that the screen
is not exposed to direct sunlight. It is best to have soft
indirect lighting while watching and avoid completely
dark environments and reflection from the screen as
these may cause eye fatigue.
Keep the TV set away from any equipment emitting
electromagnetic radiation.
2
Important Safety Instructions and Maintenance
Installation
Do not place the set on an unstable cart, stand, table
or shelf. The set may fall, causing serious personal
injury as well as damage to the product. Use only with
the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. An
appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
Do not place this apparatus near water, for example,
near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or a swimming pool; and
the like;
Move
When the TV being moved in from cold place, it needs
some right time for dew inside unit evaporating fully
before turn on the unit;
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.
LCD Screen
Although the LED screen is made with high precision technology and 99.99% or
more of the pixels are effective, black dots may appear or bright points of light (red,
blue or green) may appear constantly on the LED screen. This is a structural property
of the LED screen and is not a malfunction.
If the surface of the LCD panel cracks, do not touch it until you have unplugged the
AC power cord. Otherwise electric shock may result.
Do not throw anything at the TV set. The LCD panel may break from the impact and
cause serious injury.
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen.
Do not display still images and partially still images on the LED panel for more
than 2 hours as it can cause screen image retention. This image retention is
also known as "screen burn". To avoid such image retention, reduce the
degree of brightness and contrast of the screen when displaying a still image.
Watching the LED TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause a similar effect to the screen. Damages caused by the above effect
are not covered by the Warranty.
Displaying still images from Video games and PC for longer than a certain
period of time may produce partial after-images. To prevent this effect, reduce
the 'brightness' and 'contrast' when displaying still images.
Cleaning
Cleaning and handling the screen
surface and cabinet. Disconnect
the unit from the AC outlet before
cleaning. To remove dust, wipe
gently with a soft, lint free cloth. If
required use a slightly damp cloth.
solvent thinner
MAINS PLUG
Wipe the mains plug with
a dry cloth at regular
intervals. Moisture and
dust may lead to fire or
electrical shock.
Use care not to subject the TV's surfaces to detergent.
(A liquid inside the TV could lead to product failure, fire or
electrical shock.)
Use care not to subject surfaces to bug repellent, solvent,
thinner, or other volatile substances as this may deteriorate the
surface and finish of the cabinet.
3
Important Information
Keep small accessories out of reach of children so they are not mistakenly swallowed.
Table of Contents
Accessories----------------------------------------------------------------------------------------------- 5
Introduction----------------------------------------------------------------------------------------------- 6
Features---------------------------------------------------------------------------------------------------- 6
Specifications--------------------------------------------------------------------------------------------- 7
Stand and wall-mounting instructions (optional)-------------------------------------------------8
General Description--------------------------------------------------------------------------------10
Overview of back panel-------------------------------------------------------------------------------10
Overview of front panel------------------------------------------------------------------------------- 11
Overview of remote control-------------------------------------------------------------------------- 12
Teletext --------------------------------------------------------------------------------------------------- 14
Installing Batteries in the Remote Control------------------------------------------------------- 16
External Connection------------------------------------------------------------------------------------- 16
Antenna connection----------------------------------------------------------------------------------- 16
Connecting VCR -------------------------------------------------------------------------------------- 17
Connecting a Camcorder---------------------------------------------------------------------------- 18
Connecting a DVD Player/Set-Top Box --------------------------------------------------------- 19
Connecting a DVD Player/Set-Top Box via DVI ------------------------------------------------20
Connecting DVD Player/Set-Top Box via HDMI ------------------------------------------------21
Connecting Digital Audio System------------------------------------------------------------------ 22
Connecting PC ---------------------------------------------------------------------------------------- 23
Supporting signals --------------------------------------------------------------------------------------- 23
Basic operation--------------------------------------------------------------------------------------- 24
Turning the TV on and off----------------------------------------------------------------------------24
Menu operation ---------------------------------------------------------------------------------------- 25
Menu system instruction--------------------------------------------------------------------------------27
Picture-----------------------------------------------------------------------------------------------------27
Sound------------------------------------------------------------------------------------------------------29
Channel---------------------------------------------------------------------------------------------------31
Time--------------------------------------------------------------------------------------------------------33
Option------------------------------------------------------------------------------------------------------34
Function---------------------------------------------------------------------------------------------------36
PVR---------------------------------------------------------------------------------------------------------37
Digital Media Player ---------------------------------------------------------------------------------------40
Introduction------------------------------------------------------------------------------------------------40
Device and File Management-------------------------------------------------------------------------41
USB Support Character--------------------------------------------------------------------------------41
Photo--------------------------------------------------------------------------------------------------------41
Music--------------------------------------------------------------------------------------------------------43
Movie--------------------------------------------------------------------------------------------------------44
Text-----------------------------------------------------------------------------------------------------------47
My Disk-----------------------------------------------------------------------------------------------------48
Troubleshooting --------------------------------------------------------------------------------------------50
Picture defects and the reason-------------------------------------------------------------------------52
4
Accessories
Please make sure the following items are included with your LED TV. If any items are
missing, contact your dealer.
POWER
INPUT
1
2
4
3
6
5
7
8
9
INFO
0
RECALL
FREEZE
SLEEP
C
H
.L
V
FA
IS
T
MENU
OK/
REC LIST
U
EX
IT
G
ID
E
DTV
USB
HDMI
ASPECT
MUTE
VOL
PROG
AUDIO LANG
RED
GREEN
YELLOW
HOLD
SIZE
SUBTITLE
MIX
REVEAL
SOUND
PICTURE
INDEX
BLUE
TEXT
CANCEL
PgUp
PgDn
TIME
SUBCODE
Remote Control
CAUTION:
Batteryx2
Do not dispose of batteries in a fire. Do not short
circuit, disassemble or overheat the batteries.
Danger of explosion if battery is incorrectly
replaced, please observe polarity. Replace only
with the same or equivalent type.
Stand(1 Piece)
YPbPr cable (1to3)
and
AV cable(1to3)
M8X10,4 Pieces-see rear panel of TV.
Mounting screws
M4X10( 5 Pieces)
Stand screws
5
Introduction
Features
l
TV adopts 55” TFT LED display screen
l
Zero X radiation complies to green environment protection requirement
l
Connect to computer directly to realize TV/monitor combo.
l
16:9 wide screen
l
Auto tuning and fine tuning
l
HDMI input
l
Component Compatible (480i; 480P; 576i; 576P; 720P; 1080i; 1080P)
l
PC-RGB
l
Programmable sleep timer
l
Wide range voltage input
l
No-signal automatic power off
Input terminals used for external equipment connection
1 x ANTENNA jack
4 x HDMI inputs
1 x computer PC-RGB input
2 x USB inputs
2 x COMPONENT input
1 x AV output
2 x AV inputs
1 x SPDIF output
1 x Headphone output
6
Introduction
Specifications
Model
KALED55XX1ZA
Display size
55” Diagonal (max.)
LED panel resolution
1920X1080
Speaker output power
≥5 W X2
Power supply
~110-240V, 50/60Hz
TV receive system
Digital: DVB-T
Analog: PAL: BG, I, DK,
SECAM: BG, D/K
Frequency range
Analog: Antenna:
46.25MHz-855.25MHz
Digital:5-12, 21-69
Video in
PAL / NTSC / SECAM
Power consumption
155W
Standby consumption
<1W
Antenna Input
75 ohms, unbalanced
Controller power
DC 3V
(Two AAA size batteries)
1304X289X858mm
1304X50X810mm
25.5Kg
23Kg
Work Temperature
0 o C-40 o C
Note:
- Design and specifications are subject to change without notice.
- Weight and Dimension shown are approximate.
7
Stand and wall-mounting instructions (optional)
How to assemble the stand
If you need to remove or assemble the stand please read the following instructions.
-Before attaching/detaching the stand, make sure to turn off the TV.
-Before performing work, spread cushioning over the base area to lay the LED TV on.
This will prevent it from being damaged.
Assembling instruction:
1) Assemble the stand and the unit together with five M4*12 screws. (Figure 1)
- To disconnect the stand from the TV, perform the above steps in reverse order.
Screws(5-M4X10)
Figure 1
Securing the TV Stand
Caution: Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular,
ensure your children do not hang over or destabilize the TV; doing so may cause the TV
to tip over, causing serious injuries or death. Follow all safety precautions at the start of
this manual. For added stability, install the anti-fall device for safety purposes,
as follows.
ALTERNATIVELY
To secure the TV to the wall:
1- Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the
screws have been firmly installed onto the wall.
- You may need additional material such as an anchor depending on the type of wall.
- Since the necessary clamps, screws, and string are not supplied, please purchase them
separately.
2 - Remove the screws from the center back of the TV, put the screws into the clamps,
and then fasten the screws onto the TV again.
- Screws may not be supplied with the product. In this case, please purchase the screws
of the following specifications.
8
Stand and wall-mounting instructions (optional)
3 - Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong
cable.
- Install the TV near to the wall so that it does not fall backwards.
- It is safe to connect the string so that the clamps fixed on the wall are equal to or
lower than the clamps fixed on the TV.
- Remove the cable before moving the TV.
4 - Verify all connections are properly secured. Periodically check connections for any
sign of fatigue for failure. If you have any doubt about the security of your connections,
contact a professional installer.
Wall
Wall mounting instructions (optional)
Your LED TV is able to accommodate wall mounting with the use of a wall mount bracket
(not supplied with LED TV, please contact your local hardware store) and the mounting
holes on the back of the unit.
We recommend removing the TV stand prior to wall mounting the TV. Please see previous
page for instructions on removing the stand.
How to mount the LED TV on the wall
1.After detaching the stand, fasten 4 mounting screws (Not supplied! Please contact your
local hardware store) into the 4 screw holes on the rear cover, see the figure below.
2.Fasten wall mounting bracket (Not supplied with LED TV, please contact your local
hardware store) with screws on the wall.
3.Carefully check for the strength before releasing the LED TV.
NOTE: For more detailed instructions please refer to your “after market” wall mounting
instruction book.
Thread hole size – M6 x 10 depth (TV mounting screw size) on the TV.
9
General Description
Overview of back panel
You can connect the TV with video devices such as DVD/VCD player, VCR and video camera
to enjoy the high quality picture.
USB 2
USB 1
AV1 IN
IN
HDMI1
VGA
AUDIO
ANT
R AUDIO L
VIDEO
OUT
OUT
SPDIF
AV
USB1
HDMI 4
HDMI 3
Camcorder
PC
PC (HDMI-output)
DVD player
PC
PC (HDMI-output)
COMPONENT2/AV2 IN
L
R
AUDIO
Blu-ray disc player
Audio system
DVD player with
component output
Pr
Pb
Home theatre system
with digital input
Video game equipment
Y / V2
COMPONENT1 IN
HDMI2
USB2
L
DVD player
R
AUDIO
YPbPr
VCR
10
General Description
Overview of front panel
The buttons on the lower-right panel control your TV’s basic features, including the
on-screen menu. To use the more advanced features, you must use the remote control.
6 7
8
PROG
5
4
PROG
3
2
1
Standby button
Press
button to toggle between
normal and standby mode.
PROG
Press to change programs.
In the on-screen menu, use the
PROG
buttons as up/down
arrow buttons.
7 POWER INDICATOR
Red:In standby mode.
Green: In power on mode.
8
11
General Description
Overview of Remote Control
POWER
INPUT
1
2
3
4
5
6
7
8
9
INFO
0
RECALL
SLEEP
FREEZE
C
H
.L
V
FA
IS
T
MENU
OK/
REC LIST
E
ID
EX
U
IT
G
DTV
USB
HDMI
ASPECT
MUTE
VOL
PROG
AUDIO LANG
BLUE
RED
GREEN
YELLOW
INDEX
HOLD
SIZE
TEXT
SUBTITLE
MIX
REVEAL
CANCEL
SOUND
PICTURE
PgUp
PgDn
TIME
SUBCODE
1. INPUT: This button is used to switch among
different sources: DTV,ATV, AV1, AV2, Component1,
Component2, PC-RGB, HDMI1, HDMI2, HDMI3,
HDMI4, USB.
Select a source and press OK button to confirm.
2. POWER: Press this button to switch to standby
mode, and press it again to turn TV on.
3. Digital buttons(0~9): To select channel with
digital buttons.
4. INFO: This button is used to start the "Current
Service Banner" application that provides
information about the current service.
5. RECALL: Switch to the previous program.
6. FREEZE: Press this button to freeze the image.
7. MENU: Press this button to display main menu or
exit the menu. When you are in the submenu, you
can press it to return the main menu.
8. SLEEP: TV will be switched off automatically at
preset sleep time if you have set sleep timer. Use
your remote control to set the sleep timer.
Press SLEEP button on the remote control, then
press this button again to set sleep time: off, 10,
20,30, 60,90,120,180, 240 min. Press MENU
button to exit when you have set the sleep timer.
After you have set sleep timer, press SLEEP button
again, you will see the Remaining time.
Notes: The sleep timer you have set will be
Cancelled when the TV turns off or if a power
failure occurs.
9. CH.LIST: Press it to show channel list on screen.
10. FAV: Press it to display favorite list.
11. Arrow buttons: Press these buttons to move
cursor up/down/left/right for menu.
12. OK/REC LIST: Press this button to display a list
of recorded programs. In main menu and submenu
it is a validation button.
13. GUIDE: In DTV source, this button is used to
start the EPG application.
14. Exit: Exit the menu.
15. DTV: Switch to DTV mode.
16. HDMI: Switch to HDMI1 mode directly, press
twice to switch to HDMI2, press three times to
switch to HDMI3, press four times to switch to
HDMI4.
12
General Description
Overview of Remote Control
POWER
INPUT
1
2
3
4
5
6
7
8
9
INFO
0
RECALL
SLEEP
FREEZE
C
H
.L
V
FA
IS
T
MENU
OK/
REC LIST
E
ID
EX
U
IT
G
DTV
USB
HDMI
ASPECT
MUTE
VOL
PROG
AUDIO LANG
BLUE
RED
GREEN
YELLOW
INDEX
HOLD
SIZE
TEXT
SUBTITLE
MIX
REVEAL
CANCEL
SOUND
PICTURE
PgUp
PgDn
TIME
SUBCODE
17. USB: Switch to USB mode directly or call the
control menu in USB mode. Please see the
details in “Digital Media Player” on Page40 to Page49.
18. ASPECT: Press this button to switch the screen
mode.
19. VOL and VOL : Press these buttons to
adjust TV volume.
20. PROG and PROG : Press these buttons to
change channel upward or downward.
In the teletext, these buttons are used to
display the next page and previous page.
21. MUTE: Press this button to shut off sound of the
TV, press again to restore TV sound.
22.
Button/Audio Lang: In ATV source, the button
is used to set NICAM sound system.
In DTV source, the button is used to set the audio
language.
In USB source,the button is used to make language
soundtrack switch(video).
23. Red/Green/Yellow/Blue Command: These four
buttons are used to request linked buttons with the
current menu/page.
24. Teletext buttons: Detail operation please refer to
"Teletext “ in the next page.
25. Digital media player control button: Including
play/pause, stop, previous file, next file, page up,
page down, back, forward, is used to control in
USB mode.
Please refer to relevant instructions in the section
of multimedia player.
26. SOUND: This button is used to select the sound
mode.
Standard"
News"
Movie"
Sports"
“Dance"
Classic"
Pop"
Rock"
Jazz"
Soft"
User
27. PICTURE: This button is used to adjust user
picture mode, press this button repeatedly and
select one of four settings.
Standard"
Mild"
Bright"
User "
Sports
28. MIX (
): Teletext buttons for mix function, please
refer to page 15. It is also used for recording function
when TV is on DTV mode, please refer to page 39.
13
General Description
Teletext
POWER
INPUT
1
2
3
4
5
6
7
8
9
INFO
0
RECALL
SLEEP
FREEZE
C
H
.L
V
FA
IS
T
MENU
OK/
REC LIST
E
ID
EX
U
IT
G
DTV
USB
HDMI
ASPECT
MUTE
VOL
PROG
AUDIO LANG
13
BLUE
RED
GREEN
YELLOW
INDEX
HOLD
SIZE
TEXT
SUBTITLE
MIX
REVEAL
CANCEL
SOUND
PICTURE
PgUp
PgDn
TIME
SUBCODE
Teletext is an information system broadcast by certain
channels which be consulted like a newspaper.
It also offers to subtitles for viewers with hearing
problems or who are not familiar with the transmission
language.
You can press these buttons to operate the teletext:
Text
Press TEXT button to enter or exit teletext mode.
Hold
Press HOLD button to toggle Hold function on or
off. When Hold is switched on, the page acquisition
is stopped. When Hold is switched off, the page
acquisition is started.
Size
Press SIZE button one time to display the upper
half of the screen in double height, press the SIZE
button two times to display the lower half of the
screen in double height, press three times to
display the full screen in normal size.
Red/Green/Yellow/Blue Command
These four buttons are used for quick access to
different pages as numbered at the bottom of the
screen.
Index
Press INDEX button, then index page displays.
Reveal
Pressing this button will reveal any hidden data
(answers to quizzes for example).Press the REVEAL
button again to return to normal screen.
14
General Description
Teletext
POWER
INPUT
1
2
3
4
5
6
7
8
9
INFO
0
RECALL
SLEEP
FREEZE
C
H
.L
V
FA
IS
T
MENU
OK/
REC LIST
E
ID
EX
U
IT
G
DTV
USB
HDMI
ASPECT
MUTE
VOL
PROG
AUDIO LANG
RED
GREEN
YELLOW
BLUE
INDEX
HOLD
SIZE
TEXT
SUBTITLE
MIX
REVEAL
SOUND
PICTURE
13
13
CANCEL
PgUp
PgDn
TIME
SUBCODE
Cancel
The CANCEL button will exit from any Teletext on
the display. Press CANCEL button again to exit
Teletext and return to live TV broadcast.
Subtitle
Turning the Teletext subtitles on or off.
Subtitles is a separate mode with only a few
buttons available. There will be no OSD visible
other than the Teletext Subtitles.
Subcode
Subcode mode gives the possibility to select
certain subcode pages of a Teletext page.
Entry of digits within the range 0...9 for current
subcode entry. If the digit completes the entry,
a page request is started.
Press PAGE+/PAGE- buttons to change the
subcode pages.
Time
This button is used to show the time of the
Teletext.
Digital buttons(0~9)
You can press them to enter the number of the
Page required.
Page+/PageYou can press them to change page upward or
downward.
Mix
Press MIX botton, the teletext page changes
transparent, TV content and teletext page
content will display at the same time.
Press MIX button again to exit MIX mode.
15
General Description
Installing Batteries in the Remote Control
Installing Batteries
1
Open the battery compartment
cover on the back side.
2
Insert two 1.5V AAA size batteries
in correct polarity. Don´t mix old or
used batteries with new ones.
ATV
DTV
HDMI
SLEEP
INPUT
SOUND
PICTURE
ZOOM
Point the remote towards the remote
control sensor of the TV and use it
within 8 meters.
Put the used batteries into the recycling bin since they can negatively
affect the environment.
3
Closed the cover.
The batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like.
External Connection
Antenna connection
Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be
connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder
cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the
antenna jack. For details Please refer to the following drawing.
Antennas with 75 W
Round Leads
Antennas with 300 W
flat twins Leads
Use a 75ohm - 300ohm converter
ANT IN
75ohm coaxial cable
300ohm coaxial cable
Antenna cable
Antenna feeder
16
External Connection
Connecting VCR
These instructions assume that you have already connected your TV to an antenna or a
cable TV system. Skip step 1 if you have not yet connected to an antenna or a cable
system.
VCR Rear Panel
TV Rear Panel
1
White
Red
Blue
Red
AUDIO OUT
VIDEO OUT
Green
ANT ANT OUT S-VIDEO
USB 2
2
3
USB 1
1
2
3
RF Cable (Not supplied)
YPbPr cable(supplied)
Audio Cable (Not supplied)
HDMI 4
HDMI 3
White
L
Red
Blue
COMPONENT2/AV2 IN
Red
R
AUDIO
Pr
Pb
Green
Y / V2
COMPONENT1 IN
Follow the instructions in Viewing a VCR or Camcorder
Tape to view your VCR tape.
Each VCR has a different back panel configuration.
When connecting a VCR, match the color of the connection
terminal to the cable.
1. Unplug the cable or antenna from the back of the TV.
2. Connect the cable or antenna to the ANT IN terminal on
the back of the VCR.
3. Connect an RF Cable between the ANT OUT terminal
on the VCR and the ANT IN terminal on the TV.
4. Connect a Component Cable between the COMPONENT
[Y, Pb, Pr] jacks on the DVD player and YPbPr jack
on the TV.
5. Connect Audio Cables between the AUDIO OUT jacks
on the VCR and the AUDIO L and AUDIO R jacks on
the TV.
6. The video output can output full TV signal from Av1, Av2,
ATV, DTV.
L
R
AUDIO
YPbPr
Note: 1. Whenever you connect an external device to your TV, make sure that power on
the unit is turned off.
2. When connecting an external device, match the color of the connection terminal
to the cable.
17
External Connection
Connecting a Camcorder
The rear panel jacks on your TV make it easy to connect a camcorder to your TV. They
allow you to view the camcorder tapes without using a VCR.
Each Camcorder has a different back panel configuration.
When connecting a Camcorder or DVD, match the color of the connection terminal to
the cable.
1. Connect a Video Cable between the AV1 VIDEO jacks on the TV
and the VIDEO OUT jack on the camcorder.
2. Connect Audio Cables between the AUDIO L and AUDIO R jacks on
the TV and the AUDIO OUT jacks on the camcorder.
3. Connect a Video Cable between the component 2 IN Y on the TV
and the VIDEO OUT jack on the DVD.
4. Connect Audio Cables between the component 2 IN AUDIO L and
R jacks on the TV and the AUDIO OUT jack on the DVD.
5. Insert the small terminal on the YPbPr cable into YPbPr jack on the TV.
TV Rear Panel
USB 2
Note:
1. Whenever you connect an external device to your TV, make sure that
power on the unit is turned off.
2. When connecting an external device, match the color of the connection
terminal to the cable.
USB 1
HDMI 4
DVD Player/Set-Top Box
HDMI 3
VIDEO OUT
White
COMPONENT2/AV2 IN
Red
White
Red
Blue
Green
L
Red
Audio Cable (Not supplied)
YPbPr cable(supplied)
R
AUDIO
Pr
1 Video Cable (Not supplied)
Yellow
Yellow
White
White
Camcorder
Pb
Yellow
COMPONENT1 IN
Red
Red
2 Audio Cable (Not supplied)
AV1 IN
IN
HDMI2
HDMI1
VGA
AUDIO
Y / V2
ANT
18
R AUDIO L
VIDEO
OUT
OUT
SPDIF
AV
L
R
AUDIO
YPbPr
External Connection
Connecting a DVD Player/Set-Top Box
The rear panel jacks on your TV make it easy to connect a DVD to your TV.
Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr
(Red) for enhanced video quality.
Be sure to match the component video and audio connections.
For example, if connecting the video cable to COMPONENT IN, connect the audio cable to
COMPONENT IN also.
Each DVD player/STB has a different back panel configuration.
TV Rear Panel
When connecting a DVD player/STB, match the color of the
connection terminal to the cable.
1. Connect a Component Cable between the COMPONENT IN
[Y, Pb, Pr] terminal on the YPbPr cable(1 to 3)and the
COMPONENT [Y, Pb, Pr] jacks on the DVD player. Insert the
small terminal on the YPbPr cable (1 to 3) into YPbPr jack
on the TV.
2. Connect Audio Cables between the COMPONENT IN [R- AUDIO-L]
jacks on the TV and the AUDIO OUT jacks on the DVD player.
Note: 1.Whenever you connect an external device to your TV, make
sure that power on the unit is turned off.
2.When connecting an external device, match the color of the
connection terminal to the cable.
USB 2
USB 1
DVD Player/Set-Top Box
HDMI 4
HDMI 3
VIDEO OUT
Red
Blue
Green
COMPONENT2/AV2 IN
Red
White
Red
Blue
Green
L
R
AUDIO
Pr
Pb
Y / V2
Red
Blue
Green
Red
YPbPr cable(supplied)
COMPONENT1 IN
White
Audio cable(Not supplied)
L
R
AUDIO
YPbPr
19
External Connection
Connecting a DVD Player/Set-Top Box via DVI
This connection can only be made if there is a DVI Output connector on the external device.
DVD Player/
Set-Top Box
AV1 IN
IN
HDMI2
HDMI1
VGA
AUDIO
ANT
R AUDIO L
VIDEO
OUT
OUT
SPDIF
AV
TV Rear Panel
White
Red
2 Audio Cable
(Not supplied)
1 DVI to HDMI Cable (Not supplied)
Each DVD player/STB has a different back panel configuration.
When connecting a DVD player/STB, match the color of the connection terminal to the
cable.
1. Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI 1, HDMI 2, HDMI 3
or HDMI 4 connector on the TV and the DVI connector on the DVD player/Set-Top Box.
2. Connect Audio Cables between the PC AUDIO IN jack on the TV and the AUDIO OUT
jacks on the DVD player/Set-Top Box.
Note:
1.Whenever you connect an external device to your TV, make sure that power on the unit is
turned off.
2.When connecting an external device, match the color of the connection terminal to the
cable.
20
External Connection
Connecting DVD Player/Set-Top Box via HDMI
This connection can only be made if there is a HDMI Output connector on the external
device.
DVD Player/
Set-Top Box
AV1 IN
IN
HDMI2
HDMI1
VGA
AUDIO
ANT
R AUDIO L
VIDEO
OUT
OUT
SPDIF
AV
HDMI Cable (Not supplied)
What is HDMI?
HDMI, or high-definition multimedia interface, is a next-generation interface that enables
the transmission of digital audio and video signals using a single cable without
compression.
Multimedia interface is a more accurate name for it especially because it allows multiple
channels of digital audio (5.1 channels).
The difference between HDMI and DVI is that the HDMI device is smaller in size, has the
HDCP(High Bandwidth Digital Copy Protection) coding feature installed, and supports
multi-channel digital audio.
Each DVD player/STB has a different back panel configuration.
1. Connect an HDMI Cable between the HDMI1, HDMI2, HDMI3 or HDMI4 connector on
the TV and the HDMI connector on the DVD player/Set-Top Box.
Note:
1.Whenever you connect an external device to your TV, make sure that power on the unit is
turned off.
2.When connecting an external device, match the color of the connection terminal to the
cable.
21
External Connection
Connecting Digital Audio System
The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.
AV1 IN
IN
HDMI2
HDMI1
VGA
AUDIO
ANT
R AUDIO L
VIDEO
OUT
OUT
SPDIF
AV
Digital Audio System
TV Rear Panel
( Black)
Coaxial Cable (Not supplied)
5.1 CH audio is possible when the TV is connected to an external device supporting 5.1 CH.
1. Connect an Coaxial Cable between the SPDIF jacks on the TV and the Digital Audio Input
jacks on the Digital Audio System. When a Digital Audio System is connected to the
SPDIF terminal: Decrease the gain (volume) of the TV, and adjust the volume level with
the Digital Audio System's volume control.
22
External Connection
Connecting PC
AV1 IN
IN
HDMI2
HDMI1
VGA
AUDIO
ANT
R AUDIO L
VIDEO
OUT
OUT
SPDIF
AV
PC
2 PC Audio Cable (Not supplied)
1 D-Sub Cable (Not supplied)
Each PC has a different back panel configuration.
The HDMI jacks do not support PC connection.
1. Connect a D-Sub Cable between VGA/PC IN connector on the TV and the PC output
connector on your computer.
2. Connect a PC Audio Cable between PC AUDIO IN jack on the TV and the Audio Out jack
of the soundcard on your computer.
You should set PC software before you connect a PC to your TV (please refer to "PC
Display'' settings)
Note:
1. Whenever you connect an external device to your TV, make sure that power on the unit is
turned off.
2. When connecting an external device, match the color of the connection terminal to the
cable.
Supporting signals
Input
Mode
DVB-T
DTV
PAL BG I DK
ATV
SECAM BG DK
CVBS
Input
Input
PAL/NTSC/SECAM
Resolution
VGA
640x480
SVGA
800X600
XGA
1024X768
PC/VGA
1280X1024
SXGA
1360X768
Vertical
Frequency
60Hz
75Hz
60Hz
75Hz
60Hz
75Hz
60Hz
60Hz
23
Resolution
480i
480p
576i
Component
576p
720p
1080i
1080p
480p
576p
720p
HDMI
1080i
1080p
640x480
800X600
DVI-HDMI
1024X768
1280X1024
Vertical
Frequency
60Hz
60Hz
50Hz
50Hz
50Hz/60Hz
50Hz/60Hz
50Hz/60Hz
60Hz
50Hz
50Hz/60Hz
50Hz/60Hz
50Hz/60Hz
60Hz
60Hz
60Hz
60Hz
Basic Operation
Turning the TV On and Off
1
How to turn the TV on or off
1. Insert the power cord plug into a polarized AC outlet.
2. If TV is in standby mode Press POWER button on
the remote control or button on the bottom panel
of LED/LCD TV.
3. Normal picture will be displayed on the screen after 15 seconds. If no signal input,
"No Signal" will be displayed on the screen.
4. If temporary POWER off is required, press POWER button on the remote control or
button on the bottom panel.
5. If you want to completely switch off the power for this unit, unplug the power cord plug
for this unit.
6. After switching off the unit, you should wait at least 5 seconds before switching on again.
Status indication lamp
button is lighted: In standby mode.
Auto power-off
If there is no signal, the TV will automatically enter standby mode after 10 minutes.
See 'Auto sleep' pg. 36 for more details.
Memory before turning TV off
The picture and sound settings and preset channels will be memorised at the point when
the TV is turned off. When the TV is started up again it will work accordingly with these
settings.
24
Basic Operation
Menu operation
1
Input Setup
Press INPUT key on the remote control to enter "INPUT
SOURCE" menu. There are twelve options for you to select: DTV,
ATV, AV1, AV2, Component1, Component2, PC-RGB, HDMI1,
HDMI2, HDMI3, HDMI4 and USB Use ▲/q
key to move
the cursor to the input you desired and press OK key to confirm.
Input Source
2 Channels Selection
There are four ways to select channel:
1) Using number keys, and OK keys on the remote control to
select channel directly. To select channel 90, press 9
0
When you use the number buttons, you can directly select channels
that were either erased or not memorized.
.
DTV
ATV
AV 1
AV 2
Component1
Component2
PC-RGB
HDMI1
HDMI2
HDMI3
HDMI4
USB
Select
OK
OK
2) Using PROGr
/s
key on the remote control or on your TV to select channel.
When you press the PROGr
/s
key, the TV changes channels in sequence. You will see all the
channels that the TV has memorized.
You will not see channels that were either erased or not memorized.
3) Press RECALL key to return to previous channel, press it again to return to current
channel.
To quickly switch between two channels that are far apart, tune to one channel, then use the
number keys to select the second channel. Then use the RECALL button to quickly alternate
between them.
RECALL is not activated if no channel has been changed after TV turning on.
4) Select channels from "Channel List" or "Favorite Channels List".
Press OK key to select Channel.
3 Volume Adjustment and Mute Setup
Volume adjustment
Press VOLr
/s
key on the remote control or on the TV to display "Volume" menu,
adjust the volume of TV between 0 to 100 by using VOLr
/s
key:
( To increase the volume, press VOLr
key;
( To decrease the volume, press VOLs
key;
Mute
Press MUTE and the sound cuts off. The MUTE icon will appear in the lower-left corner
of the screen.
To resume sound, press the MUTE button again, or simply press the VOL r
key.
25
Basic Operation
Menu operation
4
Current Channel Information
Press INFO key on the remote control to view current channel information, the
indications of channel information are listed in the following table.
9
Nine Digital
DTV
576i
SD
DOLBY
MPEG
Subtitle
THE SHAK
Protugues
Wed Jun 17 2009
09:41
10:47
NEXT
12:00
Fears
Ahhhh, it’s time to face your fears!! it’s a scary day at The Shak with the theme of
Fears-Eco. Curio.
Press EXIT key on the remote control to exit this OSD.
5
GUIDE Menu
Press GUIDE key to enter “GUIDE " menu, the first line displays current channel number,
channel name, event title and current time.
The following line displays all programs that will be played on this channel, press ▲/q
key to select the program you desired.
18 Jan 2010 04:54
PROGRAMME GUIDE
DTV
9 Nine Digital
MALCOLM IN THE MIDDLE
DTV
18Jan 15:30-16:00
18Jan 16:00-16:30
Pre.Day
NextDay
MALCOLM IN THE MIDDLE
THE SHAK
No Information
No Information
No Information
No Information
Schedule
Reminder
Record
INFO
INFO
OK
OK
EXIT
Exit
DTV EPG (Electronic Program Guide)
In DTV mode, press “GUIDE” button to enter the Electronic Program Disabled. (Disabled
when there is no signal)
1. Electronic Program Guide information is provided by the broadcaster and displays
scheduled programs for the week ahead (depending upon the broadcaster).
” button to select
2. TV program of each channel is listed under the time axis. Press “t
/u
the channel and press “p
” button to highlight the program. The selected program’s
/q
background colour will change to white. Press “INFO” button to view the detailed
information. Press “OK” to select the desired channel.
3.Use the “Reminder”(blue) button to reserve programs. If the TV is in DTV mode,
it will automatically turn to the reserved program at the scheduled time. Use “Schedule”
(yellow) button to look up the reminder list.
26
Basic Operation
Menu operation
Prev.Day: If you press the red key on the remote controller, It will show Previous Day’s
programs.
Next Day: If you press the green key on the remote controller, It will show Next Day’s
programs.
Schedule: If you press the yellow key on the remote controller, It will show the reminder
list.
Reminder: If you press the blue key on the remote controller, It will show a command
window, and you can set the reserve programs.
Record: If press the record key on the remote controller it will show the RECORDER page.
INFO: you can press the INFO key on the remote controller to show information in
regards to the program you have chosen.
OK: you can press the OK key on the remote controller to select the channel you
want to view.
Exit: once you have selected a channel using the OK key, press the Exit key to view
that particular channel.
6 Install Guide
When the TV is turned on for the first time, the Installation Guide will appear, it consists of
3 parts: OSD Language, Country, Channel Tunning.
1. Press ▲/q
key to select OSD Language option,
Installation Guide
Press and ◄/►key to change Language.
2. Press ▲/q
key to select Country option, and Press
OSD Language
English
◄/►key to change Country.
Country
Australia
3. Press ▲/q
key to select Channel Tunning option,
Channel
Tuning
and press “OK” or “u
” to start tuning.
If you want to exit, press EXIT button and select “Yes”,
EXIT Exit
OK
OK
then press OK button to exit
NOTE: Install guide will also appear the first time you turn on the TV after performing the
Reset function..
Menu system instruction
Picture
PICTURE
1. Press MENU key to display the main menu on the screen.
2. Press ▲/q
key to select "Picture" option.
3. Press u
key to enter "Picture" submenu.
4. You can also press the PICTURE key on the
remote control to select one of the picture settings.
Picture Mode
Your TV has four picture settings (Standard,
Mild, Bright, user, Sports) that are preset at the
factory. Only "User" mode can be set to your
preference by adjusting particular items such as
Contrast, Brightness, Color, Sharpness, Tint .
1. Press p
/q
key to select "Picture Mode" option.
2. Press t
/u
key to select one picture mode.
27
Picture Mode
Contrast
Brightness
Color
Sharpness
Tint
Backlight
Color Temp
Select
Standard
50
50
50
50
0
80
Cool
Menu:Exit
Menu system instruction
Picture
Standard: Selects the picture for optimum display in a normal environment.
Mild: Selects the picture for comfortable display in a dark room.
Bright: Selects the picture for high-definition in a bright room.
User: Select to view your favorite display settings (see User settings for PICTURE).
Sports: Selects the picture for high-definition in a bright room.
User settings for PICTURE (Contrast, Brightness, Color, Sharpness, Tint)
Your set has several settings which allow you to control picture quality.
1. Press ▲/▼ key to select a particular item.
2. Press t
/u
key to decrease or increase the value of a particular item.
Note: The adjusted values are stored according to the selected particular item.
Contrast: Adjusts the lightness and darkness between objects and the background.
Brightness: Adjusts the brightness of the picture.
Color: Adjusts the colors, making them lighter or darker.
Sharpness: Adjusts the outline of objects to either sharpen them or make them more dull.
Tint: Adjusts the color of objects, making them more red or green for a more natural look.
Tint can only be adjusted when signal is NTSC.
Adjusting the Backlight
You can change the brightness of the entire
screen according to your preference.
1. Press p
/q
key to select "Backlight" option.
2. Presst
/u
key to select one backlight mode.
Backlight: Adjusts the brightness of the whole screen.
Adjusting the Color Temp
You can change the color of the entire screen
according to your preference.
1. Press p
/q
key to select "Color Temp" option.
2. Press t
/u
key to select one color temp.
Standard: Keeps whites white.
Warm: Makes whites reddish.
Cool: Makes whites bluish.
28
Menu system instruction
Sound
SOUND
1. Press MENU key to display the main menu on the screen.
2. Press p
/q
key to select "Sound" option.
3. Press u
key to enter "Sound" submenu.
4. You can also press the SOUND key on the
remote control to select one of the sound
settings.
Sound Mode
Sound Mode
Balance
Surround Sound
HDMI Sound
Auto Volume
SPDIF Mode
Equalizer
Standard
0
Off
HDMI
Off
PCM
You can select the type of special sound settings
Menu:Exit
Select
to be used when watching a given broadcast.
Your TV has eleven sound settings (“Standard”,“News”,
“Movie”,“Sports”, “Dance”, “Classic”, “Pop”, “Rock”, “Jazz”, “Soft”, “User”) that are
preset at the factory.
1. Press p
/q
key to select "Sound Mode" option.
2. Press t
/u
key to select one sound mode.
l
Standard: Selects the normal sound mode.
News: Provides clear and live sound for news.
l
l
Movie: Provides live and full sound for movies.
l
Sports: Emphasizes bass over other sounds.
Dance: Select the sound mode for dances.
l
Classic: Provides the classical sound for classic music.
l
Pop: Select the sound mode for Pop.
l
Rock: Provides powerful sound for Rock music.
l
Jazz: Select the sound mode for Jazz.
l
Soft: Select the soft sound mode.
l
l
User: Selects your custom sound settings (See "User settings for Sound”).
Balance
If the volumes of the left speaker and the right speaker
are not the same, you can adjust the "Balance" to suit
your personal preference.
1. Press p
/q
key to select "Balance" option.
2. Press t
/u
key to decrease or increase the value of
the item.
29
Menu system instruction
Sound
Surround Sound
This is used to turn on surround sound to gain better sound effect.
1. Press p
/q
key to select "Surround sound" option.
2. Press t
/u
key to select “Surround” or “Off”.
HDMI Sound
This option is only used in HDMI mode.
1. Press p
/q
key to select “HDMI Sound" option.
2. Press t
/u
key to select HDMI Sound mode, HDMI or PC-RGB.
Auto Volume
Each broadcasting station has its own signal conditions, and it is inconvenient to adjust
the volume every time the channel is changed. “Auto Volume” automatically adjusts the
volume of the desired channel by lowering the sound output when the modulation signal
is high or by raising the sound output when the modulation signal is low.
1. Press p
/q
key to select “Auto Volume" option.
2. Press t
/u
key to select “On” or “Off”.
.
SPDIF Mode
This is used to select "SPDIF Mode" .This option is only used in HDMI\DTV mode.
1. Press p
/q
key to select "SPDIF Mode" option.
2. Press t
/u
key to select "RAW" or "PCM".
User settings for SOUND(Equalizer)
30
SPDIF Mode
SOUND
1. Press ▲/▼ key to select an equalizer item.
2. Press OK or u
key to enter the equalizer
submenu.
The sound settings can be adjusted to suit your
user preferences.
1. Press ▲/▼ key to select a particular item.
2. Press t
/u
key to decrease or increase the
value of a particular item.
Note: The adjusted values are stored according
to the selected particular item.
PCM
Equalizer
环绕声
关
Equalizer Adjust
HDMI声音
120Hz
自动音量控制
500Hz
1.5Hz
超重低音
3KHz
丽音
7.5KHz
Select
HDMI
关
关
立体声
Menu:Return
50
50
50
50
50
Menu system instruction
Auto Search
Press p
/q
key to select "Auto Search" option. Then
press OK or u
key to start a notice window. In this
notice window, you can select country in the
“Country Selection” option and set “Tune Type” option.
Press  button to select "Start" , and press OK button
to search, then the searching interface will be on the
screen as follows:
(If you want to exit, press  / / button to select
“Cancel", and press OK button to exit.)
CHANNEL
Channel
1. Press MENU key to display the main menu on
the screen.
2. Press p
/q
key to select "Channel" option.
3. Press u
key to enter "Channel" submenu.
Auto Search
DTV Manual
Search
Please
select country first,
ThenSearch
select Start to update info.
ATV Manual
Programme Edit
Country selection
Australia
Signal Information
Tune Type
DTV+ATV
Color
System
PAL
Start
Cancel
Menu:Return
Select
The number of searched channels will be shown on the screen.
If you set “Tune Type” to “DTV+ATV”, When the searching
Auto Seach
of ATV channels is over , TV will start to search DTV channels.
When the whole searching is finished, all the channels
4 % 76.5MHz (CH3)
will be stored in memory, and a message will appear on the
ATV
: 4 Program(s)
screen as per the diagram on the right:
DTV
: 0 Program(s)
NOTE:
Radio : 0 Program(s)
1) If you want to exit the ATV searching, you can press
Data
: 0 Program(s)
MENU button, then a confirmation message will appear
on the screen.
MENU Skip
EXIT EXIT
2) To exit DTV searching, press the MENU button, a
confirmation message will then appear on the screen.
3) If you want to exit the whole searching, you can press EXIT button.
ATV Manual Search
In the ATV source, you can choose “ATV Manual Search” to
enter “ATV Manual Search” menu.
Current CH:You can see the current channel number and you can press/button to
è
choose the channel you want to modify.
è
Color System: Select the “Color System” option, Press / on the remote control or TV.
The color system will be changed repeatedly in the below order.
PAL "
SECAM
è
Sound System: Select the “Sound System” option, Press / on the remote control or TV.
The sound system will be changed repeatedly in the below order.
BG "
I"
DK
Search:
you can use  button to search channels from low frequency to high
è
frequency and use  button to search channels from high frequency to low frequency.
When you have searched a channel, the searching will be paused and you can press it again
for other channels after you store the channel.
Fine Tune: In case of unfavorable image or sound of TV program, you can use “Fine Tune”.
è
Skip: Select “Skip” option, “be changed” on the remote control or TV to swich, select “ON” to
è
skip current program, select “OFF” to add the program into the program list.
Frequency: You can see the frequency of the searched channels.
è
31
ATV Manual Search
Current CH
3
Color System
PAL
Sound System
BG
Search
Fine Tune
Skip
Frequency
Exit Exit
On
58.50 MHz
Adjust
Menu system instruction
Channel
DTV Manual Search
DTV Manual Search
In the DTV source, you can choose “DTV Manual Search” to
enter “DTV Manual Search” menu.
You can use  / button to choose the channel number and
press OK button to enter searching, and then the TV will
store the DTV channel if there is a DTV signal present.
VHF CH
7
Please select channel
Press OK to search
No Signal
Strength
Bad
Normal
Good
Bad
Normal
Good
Quality
Program Edit
You can use  / button to choose “Program Edit” and enter
the menu, press the Red/Green/Yellow/Blue color button on the
remote control to delete, rename, move and skip programs, also
you can press FAV button to add to your favorite list.
OK
OK
Menu
Return
Programme Edit
è
Delete:You can press RED button to enter "Delete" menu, then choose the channel you
want to delete and press RED button again to delete.
Move:You can press  / button to choose the channel in ATV mode you want to
è
move and press YELLOW button to move it.
è
Skip:You can press  / button to choose the channel you want to skip and press
BLUE button to skip it when you change channels.
è
FAV:If you like the program of a channel, you can choose “FAV” button in the menu to
add it to your favorite list and later you can press “FAV” button in the remote control to
choose your favorite programs as soon as possible.
Rename(green):Rename some program from program list in ATV mode you want to
È
Rename. Press  / button to selectthe program that need to be renamed, then press
green button into rename state, and press / button to select the letter that need to be
edited, and press  / button to select a new letter, repeat to rename the program.
5.1 Globo HD
TV
5.2 Globo SD
DTV
Skip
Delete
Rename
Move
FAV FAV
Return
MENU
1. Press p
/q
key to select “Signal Information" option.
2. Press “Ok”or u
key ,you can see the i nformation
of the DTV channel.
NOTE: Signal Quality/Signal Strength (DTV Only):
Unlike analogue channels, which can vary in reception
quality, digital channels must have perfect reception
quality or you will not receive them at all. So, unlike
analogue channels, you are not able fine tune a digital
channel. If the signal strength indicates that the signal
is weak, a possible solution is to adjust your antenna
to increase the signal strength. Continue to adjust the
antenna until you find the best position with the
strongest signal.
32
CHANNEL
Signal Information(Used only in DTV)
Programme Edit
Signal Information
Signal InformationPAL
Color System
Sound
System37
BG
Channel
Auto
Search Nine Melbourne
Network
DTV
Manual Search 64QAM
Modulation
ATV
Manual Search
100%
Quality
100%
Strength
Select
Menu:Return
Menu system instruction
1. Press MENU key to display the main menu on
the screen.
2. Press p
/q
key to select "Time" option.
3. Press u
key to enter "Time" submenu.
TIME
Time
Clock
10:02
On Time
Off Time
Sleep Timer
Time Zone
Off
Off
Off
WA
Clock
You can modify the time of your TV set, but when
you switch to DTV program, the "Clock" is decided
by the signal from your antenna.
TIME
Select
Off/On Time
In "Off Time" item, press  / button or OK button to
enter the submenu, set the time to turn off the
TV set.
In "On Time” item, press  / button or OK button to
enter the submenu, set the time to turn on the TV set,
when the TV set is in the standby mode.
.
Clock
Select
Menu:Return
Clock
---
You can choose it to modify your time zone in the
TV set.
1. Press p
/q
key to select "Time Zone" option.
2. Press t
/u
key to select time zone.
33
---
On Time
On Time
---------
On Time
Hour
Minute
Source
Select
Menu:Return
---
On Time
---
Off Time
Off Time
Off Time
Time Zone
-----------
Month
Year
Hour
Minute
TIME
1. Press p
/q
key to select "Sleep Timer" option.
2. Press t
/u
key repeatedly until the desired time
appears (Off, 10min, 20min, 30min, 60min, 90min,
120min, 180min, 240min).
Notes: The sleep timer you have set will be cancelled
when the TV turns off or if a power
failure occurs.
Notes: When the time is less than 60 seconds,
remind information will be displayed on the screen.
Press any key button to cancel timer function.
---
Clock
Day
TIME
Sleep Timer
Menu:Return
Hour
Minute
Select
-------
Menu:Return
Menu system instruction
OPTION
Option
1. Press MENU key to display the main menu on the screen.
2. Press p
/q
key to select "Option" option.
3. Press u
key to enter “Option” submenu.
OSD Setting
You can modify the OSD set to suit your user
preferences.
Screen Saver
This option is only used in ATV mode.
1.Press p
/q
key to select “Screen Save” option.
2.Press t
/u
to choose on or off.
Screen Saver
Aspect Ratio
Reset
Lock
Software updata(USB)
Hearing Impaired
PVR File System
Select
OPTION
1. Press p
/q
key to select “OSD Setting" option.
2. Press OK or u
key to display the OSD setting menu.
OSD Language: select the proper language
OSD Time : Set the preferred amount of time for
the OSD to be displayed on the screen.
OSD Setting
On
16:9
Off
Menu:Exit
OSD Setting
Noise Reduction
OSD SettingMIDDLE
Audio Languages
English
OSD Language
Window
Always
OSD Time
Lock
Hearing Impaired
Off
PVR File System
Select
Aspect Ratio
You can select the picture size which best corresponds
to your viewing requirement.
1. Press p
/q
key to select “Aspect Ratio" option.
2. Press t
/u
key to set the scale mode.
You can also press “Aspect” key on the remode control
to select one of the scale modes. Each source has different scale modes.
(16:9,4:3,Panorama,Movie,Subtitle, Full view,Auto)
Menu:Return
RESET
Select the “Reset” option and press OK or u
key to display a confirm box,and select”Yes”
or “No”.
Note: Please use the "Reset" option with caution as it will return all settings and channel
memories to factory default.
34
Menu system instruction
Option
Lock
The lock feature requires a Password to be entered before any settings can be changed.
1. Press MENU key to display the main menu on the screen.
2. Press p
/q
key and select "Lock" under the "Option" menu.
3. Press OK or u
key to enter "Lock" submenu, "Enter Password" menu will appear, enter
your 4-digit password to enter "Lock" submenu (the default and universal password is
0000, the almighty password is 1980).
Lock System
1. Press p
/q
key to select "Lock System" option.
2. Press t
/u
key to select "On" or "Off".
Lock System
OPTION
Set Password
1. Press p
/q
key to select "Set Password" option.
2. Enter your 4-digit password to enter enter "Change
Password" submenu. Choose any 4-digits for your
new password and enter them. As soon as the 4
digits are entered, the cursor will skip to “Confirm
Password” item, re-enter the same 4 digits, and your
new password has been memorized.
Off
Set Password
Block Program
Parental Guidance
Please enter password
Off
-- -- -- --- -- -- --
New
Confirm
Cancel
Block Program
1. Press p
/q
key to select “Block Program” option.
2. Press OK or u
key to enter Block Program list.
In the program list, use Green key to lock or unlock the
program. Once the program is locked and Lock System
is on, password is needed to enter it.
Menu:Return
Select
Block Program
5.1 Globo HD
DTV
5.2 Globo SD
DTV
Parental Guidance
This option only used in DTV mode.
1. Press p
/q
key to select “Parental Guidance” option.
2. Press t
key to select the lock level of the Parental Guidance:
/u
Off,4~18.
Software Update(USB)
1. Press p
/q
key to select “Software Update(USB)” option.
2. Press OK or u
key to software update process.
Note: In the software update process, do not turn off the power.
LOCK
EXIT Exit
Return
MENU
Hearing Impaired
Specific Hearing Impaired subtitles can be activated subject to availability from broadcaster.
Note: Only available in DTV mode.
PVR File System
1. Press MENU key to display the main menu on the screen.
2. Press p
/q
key to select “PVR File System” option.
3. Press OK or u
key to enter “PVR File System" submenu, for detailed operation refer to
“PVR File System” in page 37.
35
Menu system instruction
Function
FUNCTION
1. Press MENU key to display the main menu on the screen.
2. Press p
/q
key to select "Function" option.
Noise Redution
Off
3. Press u
key to enter “Function” submenu.
RGB Range
16-235
Noise Reduction
NoSignal PowerOff
Off
1. Pressp
/q
key to select "Noise Reduction" option.
NoAct PowerOff
Off
2. Presst
/u
key to select "Off", "Low", "Middle", "High"
Window Adjust
and "DEFAULT” to improve the picture sharpness.
Note: Noise Reduction doesn't work in PC-RGB Mode.
Advanced Setting
RGB Range
Off
Motion
Change the brightness and saturation for a better picture.
Menu:Exit
Select
1.Pressp
/q
key to select "RGB Range" option.
2.Press t
/u
key to select "16~235" or "0~255".
Note: only available in HDMI mode, please select the appropriate setting according to the
DVD Player/STB.
NoSignal PowerOff
1. Press p
/q
key to select "NoSignal PowerOff" option.
2. Presst
/u
key to set it "On" or "Off". When “NoSignal PowerOff” is turned on, the TV set
will be Power Off 15 seconds later in PC-RGB mode, 10 minutes later if there is no signal,
in other input sources,not working in USB.
NoACT PowerOff
1. Pressp
/q
key to select "NoACT PowerOff" option.
2. Presst
/u
key to set it "Off" or "1 Hour","2 Hour","4 Hour". When “NoACT PowerOff” is
turned on, the TV set will be Power Off after the set-time if there is no action.
Advanced Setting
FUNCTION
Window Adjust
This option is only used when PC mode has signal.
1. Press p
/q
key to select “Window" option.
2. Press OK or u
key to display the “Window" menu.
W
Auto Adjust: Allows you to set the TV to self-adjust to
the incoming PC video signal. The fine, coarse and
position values are adjusted automatically
w
H-Postion: Set horizontal position of picture.
w
V-Postion: Set vertical position of picture.
w
Clock/Phase: Remove or reduce picture noise.
Window Adjust
Advanced Setting
Advanced Setting
TTX Language
Primary Audio Language
Secondary Audio Language
Primary Subtitle Language
Secondary Subtitle Language
Pressp
/q
key to select "Advanced Setting" ,then press
OK or u
key to display the "Advanced Setting"menu.
TTX Language
1.Pressp
/q
key to select "TTX Language" option.
Select
2.Presst
/u
key to set TTX Language.
Primary Audio Language
1.Pressp
/q
key to select "Primary Audio Language" option.
2.Presst
/u
key to set Primary Audio Language.
Secondary Audio Language
1.Pressp
/q
key to select "Secondary Audio Language" option.
2.Presst
/u
key to set Secondary Audio Language.
Primary Subtitle Language
1.Pressp
/q
key to select "Primary Subtitle Language" option.
2.Presst
/u
key to set Primary Subtitle Language.
Secondary Subtitle Language
1.Pressp
/q
key to select "Secondary Subtitle Language" option.
2.Presst
/u
key to set Secondary Subtitle Language.
Motion
1.Press key to select “Motion” option.
2.Press key to select “Motion” ,“Off”,“On”,“Demonstrate”.
Note:This function can only be used if the TV set supports.
36
West
English
English
English
English
Menu:Return
Menu system instruction
PVR
PVR File System
WARNING:
1. Before connecting your USB device to the TV, please back up your files to prevent them
from damage or loss of data.
2. A USB disk must be formatted when first used for PVR. Any existing data on the disk will
be lost during the formatting process. Please back up your disk if you do not want to lose
this data. You are recommended to use a dedicated disk for PVR use only. Do not
disconnect disk or power during formatting.
3. Do not modify PVR files on a PC.
Note: Make sure your USB device is compatible with the TV and able to support
PVR recording.
” to choose the disk for PVR.
Select Disk: Press “OK” button to enter submenu and press “t
/u
” to set the max time for PVR Record.
Record Max Time: Press “t
/u
PVR File System
Select Disk
Record Max Time
Check PVR File System
USB Disk
Format
Time Shift Size
Speed
Disk Remaining Space
EXIT
Exit
OK
OK
PVR File System
C:
4Hr.
Start
Select Disk
C:
Record Max Time
4Hr.
Select
Disk
Check PVR File System
Start
USB Disk
Format
Disk
C:
Time Shift Size
OK
Exit
Speed
Disk Remaining Space
MB
MB
Menu
Return
EXIT
Exit
OK
OK
Menu
Return
Record Max Time: Set the maximum duration for any recording.
Check PVR File System: Press “OK” button to check if the disk is suitable for PVR.
USB Disk: Indicates PASS or FAIL for the status of your USB Disk.
Format: Press “OK” button to enter format submenu. The disk must be formatted when first
used for PVR. Do not disconnect disk or turn power off during formatting.
When formatting your disk, a progress bar will appear on the display. NOTE: The larger
your device the longer it will take to format. The device may take many minutes to
format, this is not a malfunction, please wait for the formatting to finish.
PVR File System
PVR File System
Select Disk
C:
Record Max Time
4Hr.
System SizeStart
Check PVR FileFile
System
USB DiskPVR File System Size All
Format
nat...
SD 55 Mins
HD 15 MIins
Time Shift Size
OK
Exit
Speed
Disk Remaining Space
MB
EXIT
Exit
OK
OK
Menu
Return
Select Disk
C:
Record Max Time
4Hr.
Shift Size
Check PVR FileTime
System
Start
USB Disk Time Shift Disk Size 512MB
Format
SD 14 Mins HD 4 Miins
Time Shift Size
OK
Exit
Speed
Disk Remaining Space
MB
EXIT
Exit
OK
OK
Menu
Return
Time Shift Size: This setting is available to adjust only
after the disk has been formatted. The maximum Time
Shift Size is 8G.
Speed: Display the disk writing/reading speed.
Please note: It is suggested that you use a disk with
speed that is greater than 4500KB/S.
Disk Remain Space: Display the remaning space for PVR.
NOTE: The times listed are not precise, only for reference.
PVR File System
Select Disk
Record Max Time
Check PVR File System
USB Disk
Format
Time Shift Size
Speed
Full HD support
Disk Remaining Space
EXIT
37
Exit
OK
OK
C:
4Hr.
SUCCESS
Pass
Pass
512MB
3008KB/s
384 MB
Menu
Return
Menu system instruction
PVR
PVR Guide
If the disk for PVR is ready, the programs can be
recorded in DTV mode.
Time shift
In DTV mode, press “
” button to pause the DTV
program, press it again to continue play. The length of
time a program can be paused depends upon the
setting in the PVR File System.Press “EXIT” to show or
hide the control menu.
Time Shift
POWER
INPUT
1
2
3
4
5
6
7
8
9
INFO
0
RECALL
SLEEP
FREEZE
MENU
04:55
C
H
.L
V
FA
IS
T
[- 00:00:38/00:04:00 ]
OK
OK/
REC LIST
E
ID
EX
U
IT
G
1. Current time behind live TV.
2. Total allowable time for time shifting, please see pg.
37 'PVR File System' for details in regards to setting
the Time Shift Size.
Press the PLAY button to continue playing the program
from the point where it was paused.
NOTE: Time Shift will stop if you change channels,
change inputs or go into standby mode while in Time
Shift mode. A message will appear on the display
prompting you to continue or cancel.
DTV
USB
HDMI
ASPECT
MUTE
VOL
PROG
AUDIO LANG
STOP
RED
GREEN
YELLOW
BLUE
INDEX
HOLD
SIZE
TEXT
SUBTITLE
MIX
REVEAL
CANCEL
SOUND
PICTURE
PgUp
PgDn
TIME
SUBCODE
RECORD
BACK
FORWARD
PLAY/
PAUSE
38
Menu system instruction
PVR
Instant recording
1. Select the desired channel then press the RECORD button on the remote control to start
recording the current broadcast, a progress bar will be displayed at the bottom of the screen.
- During recording, the progress bar will fade out after 10 seconds.
2. Recording stops when you press the STOP button and the recorded file is stored in the
external USB device automatically.
NOTE: You can only watch channels on the same frequency as the program being recorded.
If you try to change to another channel a message will appear prompting you to continue or
not 'Recording in progress. Change channel will stop recording. Yes or No.'
Recording in standby mode
This unit is able to do recording while in standby mode.
1. Start a recording then press the power button. A message will be displayed prompting you
to continue or cancel.
Recording
REC
9 Nine Digital
[00:00:13]
04:56
Remain [00:05:13]
At Guide menu, press “ ” button to reserve -record the selected program.
At reserve record menu, press “t
/u
” button to adjust the scheduled time, press “OK” to
save the setting and press the yellow button to check the record schedule. Recording will
proceed when the TV is in either active or standby modes. When recording initialises in
standby mode, the front panel indicators will flash momentarily, and there will be no picture
output. You can intercept the recording by turning on the power and viewing the program
that is being recorded. The schedules should not overlap, and there should be at least 1
min between two scheduled programs.
DTV
9 Nine Digital
MALCOLM IN THE MIDDLE
Programme
9 MALCOLM IN THE MIDDLE
Mode
AUTO
18 Jan 2010
Start Date
04:30
Start Time
End Date
18 Jan 2010
End Time
05:00
Back
Schedule
OK
OK
EXIT
Exit
In DTV mode, press “OK/RECLIST” to open the recorded list. Press “p
/q
” button to select
the recorded file, press “OK/RECLIST” to play the recorded file, and press the “u
” button to
show the recording information. Information. When playing, the “
”, “ ”, “ ”, “
”
, “ ”,“ ” “ ”buttons are available. Press “EXIT” to show or hide the control menu.
Recorded List
When the Recorded List is displayed
on the screen, you can delete files you
no longer require. Select the desired file
using the arrow buttons, then press the
Red button to delete.
NOTE: Files cannot be deleted during
Playback or Recording.
MALCOLM IN THE MIDDLE
MALCOLM IN THE MIDDLE
Delete Delete
OK OK
39
To. Page 1
Cu. Page 1
[DATE] 2010/01/18
[Time] 04:56:40
[PROGRAM NAME] MALCOLM IN THE MIDDLE
[CHANNEL NAME] 9 Nine Digital
[PROGRAM DESCRIPTION] If Boys Were GilsEvery time the boys are...
Digital Media Player
Introduction
This TV is embedded with one USB port digital media player. It can find devices that
support USB1.1/2.0,including flash disk, USB hard disk and digital camera. It supports
functions as: Display pictures, Play music files, Play video files, Display text files.
Note: please do not remove the cable during the data transfer. It may cause problems for
the system.
Data
Format
Picture
JPG,JPE,PNG,BMP
Music
MP3,WMA,AAC
Video
MPG,MPEG,MP4,MOV,MKV
Text
TXT
Remote Control Button
POWER
INPUT
Description of Playback Buttons:
1
2
3
4
5
6
7
8
9
INFO
0
RECALL
Buttons
SLEEP
FREEZE
MENU
PgUp
C
H
V
FA
.L
IS
T
MENU
PgDn
NAVIGATION
BUTTONS
p
q
t
u
OK/
REC LIST
OK
ID
EX
U
IT
G
E
DTV
USB
HDMI
EXIT
SUBTITLE
ASPECT
PROG
AUDIO LANG
BLUE
RED
GREEN
YELLOW
INDEX
HOLD
SIZE
TEXT
SUBTITLE
MIX
REVEAL
CANCEL
SOUND
PICTURE
PgUp
PgDn
TIME
SUBCODE
Previous file
Next file
Page up/Zoom in
Page down/Zoom out
Backward
Forward
Display the short cut key
Subtitile switch(video)
Language Soundtrack Switch(video)
MUTE
VOL
Function
Pause/Play
Stop
40
Digital Media Player
Device and File Management
Initialization Interface
Into the USB channel, the interface shown in Figure 1. If no inserted U disk, the system
will be prompted to insert the USB device, while the lower right corner screen displays
"No Device" message. When you insert a U disk, select the first letter located in the C
drive, shown in Figure 2. The corresponding buttons as follows:
Left and right keys: Select the drive letter.
Enter key: to enter the selected letter.
C
C
0/0
1/1
0/0
0/0
USB 2.0
NO DEVICE
Left / Right Key: Select
Please insert USB device
<Figure 1>
OK Key: Enter
<Figure 2>
USB support character
1. Photo
Features:Browse and play under the
specified path (the default path is specified
PHOTO
in the curre nt disk, set the photo interface
MUSIC
MOVIE
methods please refer to the specified path:
TEXT
path - Set) picture.
My Disk
Content: Browse and play all the images
0/0
1/1
under the specified path.
UP / Down key: select OK / Right Key: Enter
Photos View Shown in Figure 3
Features: Displays thumbnails of all images
<Figure 3>
path, bmp and png format does not support thumbnails.
Key operation:Up, Down, Left, Right: Option key to switch up and down.
Enter Key: elected in the entry photo option on the left, the switch to the image preview
area, was elected in the image preview area in the right section, then play image files
Exit Key: elected in the entry in the right image preview area, select the entries to switch
back to the left side of photo options, the elected option in the entry on the left picture, the
switch back to the USB interface initialization.
Photo Play interface (Shown in Figure 4)
Key operation:
The following key: Play on a picture / next picture
Left, Right: Reverse / Rotate the image clockwise
Confirmation: play / pause image
Exit: Exit the pictures to return to photo browsing
interface
Menu key: enter the playback control menu.
Shown as Figure 5
41
Street.jpg
Castle.jpg
Landscape.jpg
Landscape2.jpg
<Figure 4>
Castle2.jpg
Digital Media Player
USB support character
Play Control menu
Play
Prev
Next
Play
Prev
Next
Rotate Proportion PlayMode
Music
Stop
Music
Stop
Music
Stop
Music
Stop
Music
Stop
Key operation
Left, Right: Select Options
OK button: the selected function key to enter
the selected Living the secondary function
key menu.
<Figure 5>
Play
Play / Pause: Play / Pause Picture.
Prev: Play on a picture.
Next: Play the next picture.
Rotate: Rotate the image counter-clockwise
along. (Shown as Figure 6)
Pos-Spin
Neg-Spin
Proportion
1. Zoom Out: enlarge image(X1,X2,X4,X8)
2. Zoom In: shrink images(1/2,1/4)
3. Move View: Mobile pictures. When the picture
have been magnified over the role of screen size,
Press OK to display the arrow guide OSD, press
the arrow keys to move a picture, press the
Escape key to return to the previous menu, as
shown in Figure 7.
Rotate Proportion PlayMode
<Figure 6>
Play
Prev
Next
Rotate Proportion PlayMode
Zoom Out
Zoom In
Move View
<Figure 7>
Play
Prev
Next
Rotate Proportion PlayMode
PlayMode: Shown as Figure 8
Filmstrip
1. Filmstrip: loop all the pictures.
2. Single: Repeat the current picture.
Single
Music: Shown as Figure 9
<Figure 8>
Is set to open when the user is playing the
most recently played songs. If the user is
set to open when not playing a song recently,
the default entry to play music all the music
under.
Stop: Exit Slideshow
Play
Prev
Next
Rotate Proportion PlayMode
On
Off
<Figure 9>
42
Digital Media Player
USB support character
Playlist: Show is playing and will play the
Playlist
Info
image file. Shown as Figure 10 Up,Down
keys: select the image file OK button: Play
the selected picture file Left, Right keys:
Exit playlist, and select other options.
Exit button: Exit Playlists
Playlist
Water lilies.jpg
Blue hills.jpg
Winter.jpg
Sunset.jpg
nga_549617.jpg
Information: Display the name of the picture
playback, resolution, size and date.
(Shown as Figure 11)
2. Music
1/1
UP / Down: select
<Figure 10>
Playlist
Features: browse and play development path
is to develop the current disk, set the
method's interface, please refer to the
specified path: Path - setting) music files
under the.
Content: Displays the playback of music
files under the specified path.
OK:play
Info
Water lilies.jpg
Rsolution:
800X600
Size:
82 KBytes
Date:
----/--/--
Browse Music
<Figure 11>
Content: Displays the music files.
(Show as Figure 12)
Burning. Mp3
Key operation:
Arrow keys: up and down between the
different options about the switch.
Enter key: elected in the last entry in the left
side of music options, the switch to music
preview area; elected entries in the preview
area on the right music, then play music files.
Exit: election preview in the music entry in
the right area, select the entries to switch
back to the left side of music options; elected
entries in the music option on the left, the
switch back to the USB interface initialization
PHOTO
Jesus To A Child George Michael. Mp3
MUSIC
Bonnie Windsl. mp3
MOVIE
music_ac3_448kbps.aac
TEXT
My Disk
1/1
UP / Down key: select
OK / Right
Key: Enter
<Figure 12>
Bonnie Winds.mp3
00:00:03/00:04:07
Hold me now
Play Music
Music player interface Shown as Figure 13
Action:
Left, Right: rewind / fast forward
Upper and lower key: on a / the next one
OK button: Play / Pause music
Exit: exit the music player interface, return
to music browsing interface
Menu key: enter the playback control menu.
(Shown as Figure 14)
Don’t ever let me go again
It’s beating heart back in and answers me
(arise) my love oh lower me to his grave
And dry these tears my beating heart would bring
<Figure 13>
Bonnie Winds.mp3
Play
FB
00:00:03/00:04:07
FF
Prev
Next
PlayMode
Play Control
Key operation:
Left, Right: Select Options
Confirm the key: the selected function key
to enter the selectedfeatures live secondary
menu items.
Exit: exit the playback control menu
43
<Figure 14>
Stop
Playlist
Digital Media Player
USB support character
Action:
Bonnie Winds.mp3
Play
Up,Down keys: Select the music file
OK button: Play the selected music files
Left, Right keys: Exit playlist, and select
other options
Exit button: Exit Playlists
FB
00:00:03/00:04:07
FF
Prev
Next
PlayMode
Stop
Playlist
ByOrder
Single
PlayLoop
Function:
Play / Pause: Play / stop the music
FB: Fast back playing (x2,x4,x8,x16)
FF: Fast forward playing (x2,x4,x8,x16)
Prev: Play previous music
Next: play next music
<Figure 15>
Bonnie Winds.mp3
Play
FB
00:00:03/00:04:07
FF
Prev
Next
PlayMode
Stop
Playlist
Playlist
Burning. mp3
Jesus To A Child . Mp3
Play mode: Shown as Figure 15
1.ByOrder: Play music as order
2.Signle: Repeat single music
3.PlayLoop:Play all the music in order loop.
Bonnie Windsl. mp3
music_ac3_448kbps.aac
1/1
UP / Down: select
OK:play
<Figure 16>
Stop:Exit the music play
Bonnie Winds.mp3
00:00:03/00:04:07
Info
Playlist:
Show is playing and will play music files.
Shown as Figure 16
Bonnie Winds.mp3
Album: The Best Songs Of The World
Title: Bonnie Winds
Bit Rate: 16 Bits
Artist: Bohinta
Sampling:
Year:
Info: Display the name of music, album name,
title, stream, author, sampling year.
Shown as Figure 17.
<Figure 17>
3. Movie
Features: browse and play video files under
the specified path (default path is the current
disk, set the video interface, the method
please refer to the specified path: Path setting)
Content: Displays the playback video files
under the specified path. Shown in Figure 18
PHOTO
MUSIC
Ad.mpeg
V50.mp4
V1.RM
Divx4 ... .rmvb
Canoe_vp6.mpg
MOVIE
TEXT
My Disk
ASF_vp6.mov
1/1
UP / Down key: select
Video view
OK / Right
<Figure 18>
Key: Enter
Content: The specified path to all the video
files displayed as thumbnails
Key operation:
Arrow keys: up and down in the switch between different options.
Enter key: elected in the entry in the video options on the left, the switch to the video
preview area; elected to the entry in the right side of the video preview area, then
play the video file.
Exit: In the video preview on the right in the entry area, select the entries to switch
back to the left of the video options. Elected to the entry in the video options on the
left, the switch back to the USB interface initialization
44
Digital Media Player
USB support character
PLAY Video
Video player interface Shown as Figure 19
Action:
Left, Right: rewind / fast forward
Upper and lower key: on a / the next one
Exit: exit the video player interface, return to
video browsing interface.
Menu key: enter the playback control menu.
Shown as Figure 20
<Figure 19>
Ad.mpeg
Play
FB
00:00:03/00:04:07
FF
Switch Proportion PlayMode
Next
Prev
Play Control
Key operation:
Left, Right: Select Options
Confirm the key: the selected function key to
enter the selected. Features live secondary
menu items
Exit: exit the playback control menu.
<Figure 20>
Ad.mpeg
Action:
Play
FB
00:00:03/00:04:07
FF
Prev
Switch Proportion PlayMode
Next
Up,Down keys: Select the video file
OK button: Play the selected video files
Left, Right keys: Exit playlist, and select
other options.
Exit button: Exit Playlists
Subtitle
--/0
Track
1/1
Goto Time
Function:
<Figure 21>
Play / Pause: Play / stop the video
FB: Fast back playing (x2,x4,x8,x16)
FF: Fast forward playing (x2,x4,x8,x16)
Prev: Play previous video
Next: play next video.
Ad.mpeg
Play
FB
00:00:03/00:04:07
FF
Prev
Switch Proportion PlayMode
Next
Subtitle
Track
--/0
1/1
Goto Time
Switch: Shown as Figure 21
1. Track switch: switch the currently playing
video tracks.
2. Subtitles switch: switch the currently
playing video titles, this option the user
can switch the video comes with different
titles, select the OFF option, the subtitles will
not be displayed.
3. Time Location: Choose a specific time
period the video play the video.
Shown in Figure 22.
Input search time
0 0
: 0
0 : 0
0
Enter
<Figure 22>
Ad.mpeg
Play
FB
00:00:03/00:04:07
FF
Prev
Next
Switch Proportion PlayMode
Auto
16:9
4:3
<Figure 23>
45
Digital Media Player
USB support character
Ad.mpeg
Proportion:
Play
FB
00:00:03/00:04:07
FF
Prev
Next
Switch Proportion PlayMode
Select the display ratio video playback.
Shown in Figure 23.
1.Auto
2.16 : 9
3.4 : 3
Source of the film will switch to automatic
mode by default.
ByOrder
Single
PlayLoop
<Figure 24>
Play Mode: Shown as Figure 24
Ad.mpeg
1.ByOrder: Play video as order.
2.Signle: Repeat single video.
3.PlayLoop:Play all the video in order loop.
Set A
A->B: A to B repeat playback of video
between points
Set A: select the starting point.
Shown as Figure 25.
Set B: select the destination point .
Shown as Figure 26.
Slow
00:00:03/00:04:07
Stepping
Stop
Playlist
Info
<Figure 25>
Ad.mpeg
Set B
Slow
00:00:03/00:04:07
Stepping
Stop
Playlist
Info
None: Cancel A-> B play and resume normal
playback. As shown in Figure 27.
Slow:Play Slowly.(X2,X4,X8,X16)
Stepping: Play just one picture each time
the user clicks.
<Figure 26>
Stop:Exit the video play
Ad.mpeg
None
Slow
00:00:03/00:04:07
Stepping
Stop
Playlist
Info
Playlist: Show the videos files being playing
and will be played.
Shown as Figure 28
Info: Shows the name of the video is playing,
resolution, audio track, subtitles, program,
title, version, chapters. Shown as Figure 29.
<Figure 27>
Ad.mpeg
Set A
Slow
Ad.mpeg
00:00:03/00:04:07
Stepping
Stop
Playlist
Set A
Info
Slow
00:00:03/00:04:07
Stepping
Stop
Playlist
Info
Playlist
Ad.mpeg
Ad.mpeg
V50.mp4
V1.RM
Divx4....rmvb
Divx5....rmvb
Resolution:
Audio Track:
1/1
UP / Down: select
--/0
Title:
--
Edition:
--
Chapter:
--
<Figure 29>
46
1 /1
--/0
Program:
OK:play
<Figure 28>
352x288
Subtitle:
Digital Media Player
USB support character
4.Text
Features: browse and play text files under the
specified path (default path is the current disk,
set the video interface, the method please refer
to the specified path: Path - setting)
Content: Displays the playback text files under
the specified path.
Shown in Figure 30
The Wonderful Wizard of Oz . txt
PHOTO
Around the World in 80 Days. txt
MUSIC
How To Be Happy At Work. txt
MOVIE
Ernest Hemingway's corpus. txt
TEXT
Jane Eyre. Txt
My Disk
1/1
Document view
UP / Down key: select
Content: The specified path to all the document
files displayed as thumbnails.
Key operation:
Arrow keys: up and down in the switch between
different options.
Enter key: elected in the entry in the document
options on the left, the switch to the video preview
area; elected to the entry in the right side of the
document preview area, then play the document
file.
Exit: In the video preview on the right in the entry
area, select the entries to switch back to the left
of the document options. Elected to the entry in
the document options on the left, the switch back
to the USB interface initialization
OK / Right
Key: Enter
<Figure 30>
How To Be Happy At Work
it’s not easy to tell others how to be happy at work,
especially people who feel as if they’re living in a career combat zone.
i know the battleground well. for the past 20 years,
i’ve been a career counselor, psychotherapist,
and corporate outplacement consultant. in that time,
i’ve seen more casualties of the career wars than most people experience in a
lifetime. i know what it takes to be happy with your work. but i also know there’s
no simple formula to achieve career success and satisfaction.
the workplace is chaotic. if you’re like most people, you probably feel that you’re
living a career nightmare: working harder to make a living with fewer available
resources, more demands on your time, and lots of disincentives to achievement.
perhaps you fantasize about chucking the whole scene. right about now, life on
the golf course, ski slopes, or a sandy beach can look mighty appealing.
maybe you just need a good, long vacation. you don’t want to drop out of the
workforce altogether, but you’re hungering for a new adventure. you want more
control over your time and your destiny. your rallying cry is more freedom, less
office politics!
1/2
UP: Pre Page DOWN: Next Page LEFT: Pre File RIGHT: Next File
<Figure 31>
Documents Reading
The Documents Reading iinterface: Shown as
Figure 31.
Key operation
Up,Down keys: Previous Page, Next Page
Left, right keys: Previous document, Next
document.
Exit key: Return to the document interface
Menu key: Enter the playback control menu.
As shown in Figure 32.
Prev Page Next Page
Prev
Next
Stop
Music
How To Be Happy At Work
Goto Page
Playlist
GO
TO
it’s not easy to tell others how to be happy at work,
especially people who feel as if they’re living in a career combat zone.
i know the battleground well. for the past 20 years,
i’ve been a career counselor, psychotherapist,
and corporate outplacement consultant. in that time,
i’ve seen more casualties of the career wars than most people experience in a
lifetime. i know what it takes to be happy with your work. but i also know there’s
no simple formula to achieve career
0 success
0 0 and
0 satisfaction.
the workplace is chaotic. if you’re like most people, you probably feel that you’re
OKto make a living with fewer available
living a career nightmare: working harder
resources, more demands on your time, and lots of disincentives to achievement.
perhaps you fantasize about chucking the whole scene. right about now, life on
the golf course, ski slopes, or a sandy beach can look mighty appealing.
maybe you just need a good, long vacation. you don’t want to drop out of the
workforce altogether, but you’re hungering for a new adventure. you want more
control over your time and your destiny. your rallying cry is more freedom, less
office politics!
1/2
Play Control menu
Key operation
Left, Right: Select Options
OK button: the selected function key to enter the
selected Living the secondary function key menu.
Exit button: Exit Play control menu.
UP: Pre Page DOWN: Next Page LEFT: Pre File RIGHT: Next File
<Figure 32>
Prev Page Next Page
Prev
Next
Stop
Music
How To Be Happy At Work
Function
Goto Page
Playlist
GO
TO
it’s not easy to tell others how to be happy at work,
especially people who feel as if they’re living in a career combat zone.
i know the battleground well. for the past 20 years,
i’ve been a career counselor, psychotherapist,
On
and corporate outplacement consultant. in that time,
i’ve seen more casualties of the career wars than most people experience in a
Off
lifetime. i know what it takes to be happy with your work. but i also know there’s
no simple formula to achieve career success and satisfaction.
Prev Page: Show previous page.
Next Page: Show next page.
Prev: Show previous document.
Next: Show next document.
the workplace is chaotic. if you’re like most people, you probably feel that you’re
living a career nightmare: working harder to make a living with fewer available
resources, more demands on your time, and lots of disincentives to achievement.
perhaps you fantasize about chucking the whole scene. right about now, life on
the golf course, ski slopes, or a sandy beach can look mighty appealing.
maybe you just need a good, long vacation. you don’t want to drop out of the
workforce altogether, but you’re hungering for a new adventure. you want more
control over your time and your destiny. your rallying cry is more freedom, less
office politics!
1/2
Stop: Exit document reading
Music: Shown as Figure 33
When set to open, play music at the same time.
47
UP: Pre Page DOWN: Next Page LEFT: Pre File RIGHT: Next File
<Figure 33>
Digital Media Player
USB support character
Goto Page: Select this feature, the pop-up
dialog box jump page, the user can enter the
page number to view the page, select OK
option, and enter the designated page, click
Exit to return to playback control menu.
Playlist: displays document files can be
played. Shown as Figure 34;
Show the name, size of the document playing.
As shown in Figure 35.
Prev Page Next Page
Prev
Next
Stop
Music
Goto Page
Playlist
GO
TO
Playlist
The Wonderful Wizard of Oz . txt
Around the World in 80 Days. txt
How To Be Happy At Work. txt
Ernest Hemingway's corpus. txt
Jane Eyre. Txt
1/1
UP / Down: select
OK:play
UP: Pre Page DOWN: Next Page LEFT: Pre File RIGHT: Next File
<Figure 34>
5. My Disk
Function: Displays the current disk under the
folder, movies, music, pictures, text files;
set "Photo", "music", "video", "document" the
specified path. Shown as Figure 36.
Key operation:
Arrow keys: up and down between the different
options about the switch.
Enter key: If the focus is on the left side when
Regional Options, switch to the right area;
when the focus is on the right side file display
area, if the focus on the folder, then into the
folder. If movies, music, pictures, text, and
then play the file.
Exit: If the focus is on the left, the switch back
to the USB initialization interface; if the focus
is on the right side of the menu and when in the
root directory, then switch to the left region, if
the focus is on the right side when the non-root
directory, then return to the previous level
directory. Set path Description: display area is
selected in the file folder, the folder will appear
to set the right function. Right-click the arrow
keys to select the settings option and then
press the OK button will pop up settings dialog,
set the box includes two
options: the current disk and the current path.
Up and down keys to switch between these two
options, select the OK button is selected the
path way out to save the current settings and
launch path settings menu.
As shown in Figure 37
Info
How To Be Happy At Work. txt
it’s not easy to tell others how to be happy at work,
especially people who feel as if they’re living in a career combat zone.
i know the battleground well. for the past 20 years,
i’ve been a career counselor, psychotherapist,
and corporate outplacement consultant. in that time,
i’ve seen
more
casualties
the career
How
To Be
Happy AtofWork.
Txt wars than most people experience in a
lifetime. i know what it takes to be happy with your work. but i also know there’s
no simple
career success and satisfaction.
Size: formula to achieve
115.92Kbytes
the workplace is chaotic. if you’re like most people, you probably feel that you’re
living a career nightmare: working harder to make a living with fewer available
resources, more demands on your time, and lots of disincentives to achievement.
perhaps you fantasize about chucking the whole scene. right about now, life on
the golf course, ski slopes, or a sandy beach can look mighty appealing.
maybe you just need a good, long vacation. you don’t want to drop out of the
workforce altogether, but you’re hungering for a new adventure. you want more
control over your time and your destiny. your rallying cry is more freedom, less
office politics!
1/2
UP: Pre Page DOWN: Next Page LEFT: Pre File RIGHT: Next File
<Figure 35>
Setup
Landscape2.jpg
PHOTO
MUSIC
Street.jpg
Ad.mpeg
Current Drive
Burning. Mp3
MOVIE
Setup
Current Path
Jesus To A Child
George
Index
Path Michael. Mp3
TEXT
Ernest Hemingway's corpus. txt
My Disk
Jane Eyre. txt
1/1
UP / Down key: select
OK / Right
Curren Path C:\
Setup
Landscape2.jpg
PHOTO
MUSIC
MOVIE
Street.jpg
Ad.mpeg
Burning. Mp3
Jesussettings
To A Child
Saving
......George Michael. Mp3
TEXT
Ernest Hemingway's corpus. txt
My Disk
Jane Eyre. txt
1/1
UP / Down key: select
OK / Right
<Figure 37>
48
Key: Enter
<Figure 36>
Key: Enter
Digital Media Player
USB support character
Current Disk: Set "Photo", "music", "video", "document" for the entire query path
specified disk. This option is selected, each time a user visit the "Photo", "music",
"video", "Documents" for the current disk contains all the photos / music / video /
document file. Entry: If you enter the C drive, when setting the current disk is
selected, the view, "photo", "music", "video", "document" is displayed when the
C drive, all photos / music / video / document file. As to the current disk to find the
entire disk media files, so speed will be very slow, do not recommend this path set up.
Current Path: Set "Photo", "music", "video", "document" of the specified query path
for the currently selected folder path. when choosen, each time a user browsing
photos, music, video, document files is the current folder contains all the photos /
music / video / document files.For example,the currently selected folder is
"KKDOWNLOAD", when elected in the current path, browsing the "photo", "music",
"video", "document" to display all photos / music / video / document files in the
"KKDOWNLOAD" folder.This will be faster when serching.Therefore, it is strongly
recommended that users put all kinds of media files in a fixed folder and set folder
to specify the path, so you can save search time.
49
Troubleshooting
If you have any problem, check the couter measures for each symptom listed beiow.
The following symptoms may have been. caused by inappropriate adjustment rather
than actual malfunction of the unit. If the trouble persists, contact the Customer Care
Centre, see back page for contact details .
Symptoms
Possible solutions
No power
Please check the power cord plugged in and that the power
outlet works .
Unplug the power cord and plug it in after 60 seconds and
restart the TV.
No picture
Please check antenna connection.
Station may be experiencing problems, please tune to
another station.
Please adjust the settings of contrast and brightness.
Good picture but no
sound
Please increase the volume.
Please check TV is under mute mode, press MUTE button
on the remote control.
Please check sound settings
If external devices are being used, check their volumes are
not set too low or turned off.
If using AVI or Component inputs, please make sure cables
are connected prpoerly and not loose.
If using DVI to HDMI cable, a separate audio cable is required.
Make sure a headphone jack is not connected..
Please check antenna connection and antenna condition.
Good sound but abnormal If using Component input, please check Component
connections, incorrect or loose connections may cause
color or no picture
colour problems or cause the screen to be blank.
Batteries of remote control may have exhausted, if
necessary, please change the batteries.
No response to remote Clean the remote control lens. The distance between
control
LED TV and remote control should be within 8m, within
recommended operating angle and path is free of obstructions.
Full screen flickering
under VGA
V-HEIGHT value may be set too big, restart computer and
enter safe mode, then set monitor parameters to correct
value according to adjustment description.
Horizontal stripes
under VGA
Sample phase may be deflected, adjust phase according to
picture position.
Colored dots may be
present on the screen
Although the LCD screen is made with high-precision
technology and 99.99% or more of the the pixels are
effective, black dots may appear or bright points of light
(red, blue, or green) may appear constantly on the LCD
screen. This is a structural property of the LCD screen
and not a malfunction.
Picture is breaking up
Keep the TV away from noisy electrical sources such as cars,
hair dryers, welders, and all optional equipment.
Electrical atmospheric interference such as local or distant
lightning storms may cause picture to break up.
When installing optional equipment, leave some space
between the optional equipment and the TV.
Check the antenna and connection.
Keep the antenna away from any power or input/output cables.
50
Troubleshooting
After Auto Tuning only
some channels are
available
Check your area is covered by Digital Video Broadcasts.
Try re-tuning or manually tuning missing channels.
Check that you are using the correct antenna type - please
see pg.16 'Antenna connection'.
Channel cannot be
selected
Check if the channel has been blocked in the main menu
settings.
USB not playing
Please check connecting USB cable and power supply is
connected.Hard drive has not been formatted. Please make
sure USB disk is compatible and the multimedia data formats
are supported.
Picture is distorted,
Compression of video contents may cause distortion
macroblock, small block, especially on fast moving pictures such as sports and
dots, pixelization, etc
action movies.
Noise from speaker
Check cable connections, make sure a video cable is not
connected to an audio input.
Low signal level may cause sound distortion.
Check if the Off Timer is set to On in the Setup menu.
Sleep Timer may have been enabled.
If there is no signal for about 10 minutes from an input,
TV turns off automatically the TV will turn off, see Auto Sleep pg. 33.
If connected to your PC, check your PC power settings.
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
TV turns on
automatically
Picture is not shown in
full screen
Check if the On Timer is set to On in the Setup menu.
Black bars on each side will be shown on HD channels
when displaying SD (4:3) contents.
Black bars on Top & Bottom will be shown on movies that
have aspect ratios different from your TV.
Adjust picture size option on your external device or TV to
full screen.
51
Troubleshooting
Picture defects and the reason
Ghosting may also occur when still pictures are
displayed continuously. It may disappear after a
few moments.
52
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement