Graco 307260D AIRLESS SPRAY GUN MODEL 210890 "C" Owner's Manual


Add to my manuals
8 Pages

advertisement

Graco 307260D AIRLESS SPRAY GUN MODEL 210890
INSTRUCTIONS-PARTS LIST 307-260
This manual contains IMPORTANT do Rev D
READ AND RETAN FOR REPAS Supersedes C
AIRLESS SPRAY GUN
4500 psi (310 bar) Maximum Working Pressure
Model 210-890, Series C
Warnings ................................. 2,3
Installation .........................,...... 4
Operation ................................. 4,5
Troubleshooting ............................. 6
Service .................................. 6
Parts Drawing and List........................ 7
Accessories ........................ Back Cover
Technical Data....................... Back Cover
Warranty ............................ Back Cover
GRACO INC. PO. BOX 1441 MINNEAPOLIS, MN 55440-1441
© COPYRIGHT 1976, GRACO, INC.
WARNING
HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY.
FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS.
Read and understand all instruction manuals before operating equipment.
FLUID INJECTION HAZARD
General Safety
Airless spray equipment generates very high fluid pressure.
Spray from the gun, leaks or ruptured components can inject
fluid through your skin and into your body and cause extreme-
ly serious bodily injury, including the need for amputation.
Also, fluid injected or splashed into the eyes or onto the skin
can cause serious damage.
NEVER point the spray gun at anyone or at any part of the
body. NEVER put hand or fingers over the spray tip. NEVER
try to “blow back” paint; this is NOT an air spray gun.
ALWAYS have the tip guard in place on the spray gun when
spraying.
ALWAYS follow the Pressure Relief Procedure, to the
right, before cleaning or removing the spray tip or servicing
any system equipment.
NEVER try to stop or deflect leaks with your hand or body.
Be sure equipment safety devices are operating properly
before each use.
Medical Alert— Airless Spray Wounds
If any fluid appears to penetrate your skin, get EMERGENCY
MEDICAL CARE AT ONCE. DO NOT TREAT AS A
SIMPLE CUT. Tell the doctor exactly what fluid was injected.
Note to Physician: Injection in the skin is a traumatic in-
jury. It is important to treat the injury surgically as soon
as possible. Do not delay treatment to research toxicity.
Toxicity is a concern with some exotic coatings injected
directly into the blood stream. Consultation with a plastic
surgeon or reconstructive hand surgeon may be advisable.
Spray Gun Safety Devices
Be sure all gun safety devices are operating properly before
each use. Do not remove or modify any part of the gun; this
can Cause a malfunction and result in serious bodily injury.
Safety Latch
Whenever you stop spraying, even for a moment, always
engage the gun safety latch in the closed or ON SAFE posi-
tion, making the gun inoperative. Failure to engage the safety
latch can result in accidental triggering of the gun. See Fig 2,
page 4.
Diffuser
The gun diffuser breaks up spray and reduces the risk of fluid
injection when the tip is not installed. Check diffuser operation
regularly. Follow the Pressure Relief Procedure, below,
then remove the spray tip. Aim the gun into a grounded metal
pail, holding the gun firmly to the pail. Using the lowest possi-
ble pressure, trigger the gun. If the fluid emitted is not diffused
into an irregular stream, replace the diffuser immediately.
Tip Guard
ALWAYS have the tip guard in place on the spray gun while
spraying. The tip guard alerts you to the fluid injection hazard
and helps reduce, but does not prevent, the risk of accidental-
ly placing your fingers or any part of your body close to the
spray tip.
Trigger Guard
NEVER operate the gun with the trigger guard removed. The
trigger guard reduces the risk of accidentally triggering the
gun if it is dropped or bumped.
2 307-260
Spray Tip Safety
Use extreme caution when cleaning or changing spray tips. If
the spray tip clogs while spraying, engage the gun safety latch
immediately. ALWAYS follow the Pressure Relief Pro-
cedure, below, and then remove the spray tip to clean it.
NEVER wipe off build-up around the spray tip until pressure is
fully relieved and the gun safety latch is engaged.
Pressure Relief Procedure
To reduce the risk of serious bodily injury, including fluid injec-
tion; splashing in the eyes or on the skin; or injury from mov-
ing parts, always follow this procedure whenever you shut off
the spray equipment, when checking or servicing any part of
the spray system, when installing, cleaning or changing spray
tips, and whenever you stop spraying.
. Engage the gun safety latch.
. Shut off the power supply to the pump and close any
bleed-type master air valves in the air supply.
Disengage the gun safety latch.
Hoid a metal part of the gun firmly to the side of a ground-
ed metal pail, and trigger the gun into the pail to relieve
pressure.
5. Engage the gun safety latch.
6. Open the pump fluid drain valve (required in the system),
having a container ready to catch the drainage.
7. Leave the drain valve open until you are ready to spray
again.
PO No
IF you suspect that the spray tip or hose is completely clogged,
or that pressure has not been fully relieved after following the
steps above, VERY SLOWLY loosen the tip guard retaining
nut or hose end coupling and relieve pressure gradually, then
loosen completely. Now clear the tip or hose.
EQUIPMENT MISUSE HAZARD:
General Safety
Any misuse of the spray equipment or accessories, such as
overpressurizing, modifying parts, using incompatible
chemicals and fluids, or using worn or damaged parts, can
cause them to rupture and result in fluid injection or other
serious bodily injury, fire, explosion or property damage.
NEVER alter or modify any part of this equipment; doing so
could cause it to malfunction.
CHECK all spray equipment regularly and repair or replace
worn or damaged parts immediately.
Read and follow the fluid solvent manufacturer’s literature
regarding the use of protective clothing and equipment.
System Pressure
DO NOT exceed 4500 psi (310 bar} MAXIMUM WORKING
PRESSURE to the gun. Be sure all accessory items and
system components are rated to withstand the pressures
developed. NEVER exceed the pressure rating of any compo-
nent in the system.
Fluid Compatibility
BE SURE that all fluids and solvents used are chemically com-
patible with the wetted parts shown in the Technical Data on
the back cover. Always read the manufacturer's literature
before using a fluid or solvent in the system.
FIRE OR EXPLOSION HAZARD
Static electricity is created by the high velocity flow of fluid
through the pump and hose. If every part of the Spray equip-
ment is not properly grounded, Sparking May occur, and the
dust particles and other flammable substances, whether you
are spraying indoors or outdoors, and can cause a fire or ex-
plosion and serious bodily injury and property damage. Do not
plug in or unplug any power supply cords in the Spray area
when there is any chance of igniting fumes still in the air.
If you experience any static sparking or even a slight shock
while using this equipment, STOP SPRAYING IM-
MEDIATELY. Check the entire system for proper grounding.
Do not use the system again until the problem has been iden-
tified and corrected.
Grounding
To reduce the risk of Static sparking, ground all the spray
equipment used or located in the spray area. CHECK your
local electrical code and your equipment's individual instruc-
tion manuals for detailed grounding instructions for your area
and type of equipment and be sure to ground all of this spray
equipment:
1. Pump or Sprayer: as instructed in your separate pump or
Sprayer manual.
2. Air compressor or hydraulic power supply: according to
local code.
3. Fluid hoses: use Only grounded hoses with a maximum of
500 feet (150 т) combined hose length to ensure ground-
ing continuity. Refer to Hose Grounding Continuity,
below.
4. Spray gun: obtain grounding through connection to a
properly grounded fluid hose and Sprayer or pump.
5. Fluid supply container: according to local code.
6. Object being sprayed: according to local code.
7. All solvent Pails used when flushing, according to local
code. Use only metal pails, which are conductive. Do not
place the pail on a non-conductive surface, such as paper
or cardboard, which interrupts the grounding continuity.
8. To maintain grounding continuity when Hushing or reliev-
ing pressure, always hold a metal part of the gun firmly to
the side of a meta/ pail, then trigger the gun.
Flushing Safety
Before flushing, be sure the entire system and flushing pails
are properly grounded. Refer to Grounding, above. Follow
the Pressure Relief Procedure on page 2, and remove the
spray tip from the gun. Always use the lowest possible fluid
pressure, and maintain firm metal-to-metal contact between
the gun and a grounded metal pail during flushing to reduce
the risk of a fluid injection injury, static Sparking and
splashing.
HOSE SAFETY
High pressure fluid in the hoses can be very dangerous. If the
hose develops a leak, split or rupture due to any kind of wear,
damage or misuse, the high pressure Spray emitted from it can
cause a fluid injection injury or other serious bodily injury or
property damage.
ALL FLUID HOSES MUST HAVE SPRING GUARDS ON
BOTH ENDS! The spring guards help protect the hose from
kinks or bends at or close to the coupling which can result in
hose rupture.
TIGHTEN ail fluid connections securely before each use. High
pressure fluid can dislodge a loose coupling or allow high
Pressure spray to be emitted from the coupling.
NEVER use a damaged hose. Before each use, check the en-
tire hose for cuts, leaks, abrasion, bulging cover, or damage or
HANDLE AND ROUTE HOSES CAREFULLY. Do not pull on
hoses to move equipment. Do not use fluids or solvents which
are not Compatible with the inner tube and cover of the hose.
DO NOT expose Graco hose to temperatures above 180°F
(82°C) or below -40°F (-40°C).
Proper hose grounding continuity is essential to maintaining a
grounded Spray system. Check the electrical resistance of your
your system hazardous. Also read FIRE OR EXPLOSION
HAZARD, above.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers or other
body parts. KEEP CLEAR of moving parts when starting or
operating your system. Disconnect the power source and
relieve pressure by following the Pressure Relief Procedure
on page 2 before checking or servicing your system to prevent
the pump from Cycling accidentally.
TERMS ©
WARNING: Alerts user to avoid or correct conditions
that could cause bodily injury.
CAUTION: Alerts user to avoid or correct conditions
that could damage the equipment.
NOTE: Gives special procedures or information.
IMPORTANT
United States Government safety standards have been adopted under the Occupational Safety and Health Act. These standards — par-
ticularly the General Standards, Part 1910, and the Construction Standards, Part 1928— should be consulted.
307-260 3
NSTALLATION : _
IOTE: Numbers and letters in parentheses in the
text correspond to the reference numbers
and letters in the text and drawings.
WARNING
Be sure your system has a bleed-type master air
valve (pneumatic pumps only) and a fluid drain
valve. These two accessories help reduce the risk
of serious bodily injury, including fluid injection,
splashing in the eyes, or on the skin, or injury from
moving parts, if you are adjusting or repairing the
pump or gun.
1. The b/eed-type master air valve relieves air trap-
ped between this valve and the pump after the
air regulator is shut off. Trapped air can cause
the pump to cycle unexpectedly.
1/4 npt(f)
2. The fluid drain valve assists in relieving fluid
pressure in the displacement pump, hose and Fig 1
gun; triggering the gun to relieve pressure may |
not be sufficient. 4. With the gun safety latch engaged, unscrew the tip
guard (18) and install the tip (B) and gasket (17) in
the nut of the tip guard. Screw the assembly firmly
1. Connect a grounded fluid hose to the gun inlet. onto the gun. Tighten with a wrench. See Fig 1.
2. With no tip installed, start the pump/sprayer. Flush NOTE: Failure to install the tip gasket (17) will result
it according to the instructions supplied with it. in leaking.
Prime the system with the fluid you are using.
5. Strain the fluid you are spraying if it contains par-
3. Follow the Pressure Relief Procedure on page 2. ticles which could clog the spray tip.
ee CE te — Eee tee
| 3 SS RR RS SS
JP E RA IO N ES : SEP SHS НЯ о RAR na
_ WARNING
To reduce the risk of serious bodily injury, in-
cluding fluid injection or splashing in the eyes or on
the skin, always follow the Pressure Relief Pro-
cedure Warning on page 2 before checking, ser-
vicing, installing, removing, changing or cleaning
spray tips or any part of the gun or system.
Whenever you stop spraying for a moment,
engage the gun safety latch. See Fig 2.
WARNING
The wallet-sized warning card provided with this
gun should be kept with the operator at all times.
The card contains important treatment information SAFETY LATCH
should an injection injury occur. Additional cards IN OFF SAFE
are available at no charge from Graco Inc. POSITION
1. Start the pump. Adjust the fluid pressure so the
spray is completely atomized. Always use the
lowest pressure necessary to get the desired results.
Higher pressure may not improve the spray pattern
and will cause premature tip and pump wear.
SAFETY LATCH
2. If adjusting the pressure does not give a good spray INN
pattern, try another tip size. Be sure to relieve
pressure completely before changing tips. Fig 2
3. Use a full-open, full-close trigger action. Hold the
gun about 14 in. (350 mm) from and at right angles
to the work surface. Don’t swing the gun in an arc.
Practice to find the best length and speed of stroke.
307-260
Adjust the Spray Pattern
1. To adjust the spray pattern direction, follow the
Pressure Relief Procedure Warning on page 2.
Engage the safety latch and loosen the tip guard re-
taining nut. Turn the spray tip so the groove is
horizontal for a horizontal spray pattern, and vertical!
for a vertical pattern.
2. The spray tip orifice size and spray angle determines
the coverage and size of pattern. When more
coverage is needed, use a larger spray tip rather
than increasing fluid pressure.
WARNING
To reduce the risk of a fluid injection injury,
NEVER use the gun with the tip guard or trigger
guard removed.
CAUTION
Openings in the tip guard are designed to reduce
paint buildup on the guard while spraying. Any
damage to the sharp edges of the openings causes
paint to collect at that area. To reduce the risk of
damage, never hang the gun by the tip guard.
Cleaning and Clearing the Spray Tip
WARNING
To reduce the risk of a fluid injection or splashing
in the eyes or on the skin, DO NOT hold your
hand, body, or a rag in front of the spray tip when
cleaning or checking a clogged tip. Always point
the gun toward the ground or into a waste con-
tainer when checking to see if the spray tip is
cleared.
DO NOT try to “blow back” paint; this is NOT an
air spray gun.
DO NOT wipe fluid buildup off the gun or spray tip
until pressure is relieved. See the Pressure Relief
Procedure Warning on page 2.
Clean off the front of the tip frequently during the day's
operation and at the end of the work day. Always follow
the Pressure Relief Procedure Warning on page 2.
Then use a solvent soaked brush to clean the spray tip
and to keep fluid buildup from drying and clogging the
spray tip.
If the spray tip clogs while spraying, release the spray
gun trigger, engage the trigger safety, shut off the
pump, and follow the Pressure Relief Procedure
Warning on page 2. Then remove the spray tip and
blow out the obstruction with air from the front of the
spray tip, or let the spray tip and gun nozzle soak long
enough to dissolve the obstruction. If it won't dissolve,
jar it out by tapping the back of the spray tip against a
flat surface.
NEVER soak the entire gun in solvent. Prolonged
CAUTION |
exposure to solvent can гит the packings. |
Flushing the Gun
WARNING
Before flushing, be sure the entire system and
flushing pails are properly grounded. Refer to
Grounding, on page 3. Follow the Pressure
Relief Procedure Warning on page 2, and
remove the spray tip from the gun. Always use the
lowest possible fluid pressure, and maintain firm
metal to metal contact between the gun and the
pail during flushing to reduce the risk of a fluid in-
jection injury, static sparking and splashing.
Relieve pressure, remove the spray tip, and then flush
the gun and spray system with a compatible solvent.
Always flush the gun before the fluid being sprayed can
dry in it.
MAINTAIN FIRM
METAL-TO-METAL
CONTACT BETWEEN
GUN AND GROUNDED
METAL CONTAINER
Fig 3
TROUBLESHOOTING:
If the valve won't stop spraying, check the clearance
between the tip of the trigger and the safety latch. See
Adjusting the Trigger on page 6. Also disassemble
and clean gun.
If fluid leaks around the packing nut, the packings
and/or needle may need replacing.
307-260 5
=RVICE:
WARNING
mm
To reduce the risk of serious bodily injury, in-
cluding fluid injection or splashing in the eyes or
on the skin, always follow the Pressure Relief
Procedure Warning on page 2 before checking,
adjusting or repairing the gun.
a
Relieve pressure. Disconnect the hose. Remove the
tip guard.
. Unscrew the trigger guard retainng nut (21) and
remove the trigger. See Fig 4.
- Unscrew the nipple (20) from the gun body (22).
Unscrew the locknut (9) and screw (8) from the top
of the gun body. See Fig 4.
. Swing the trigger (11), out of the way. See Fig 5.
_ Unscrew the packing nut (6) and remove the valve
stem (14). Using a wire hook, pull the packings (10)
and gland (5) out of the body (22).
‚ Unscrew the lower body (13) from the upper body
(22). Remove the spring (15), spring and ball re-
tainer (16) and ball (2).
. Clean and inspect all parts. Replace any worn or
damaged parts.
NOTE: When replacing the packings (10), replace all
four and the gland (5) at the same time.
Reinstall the parts in the lower gun body (13). See
Fig 4. Tighten body (13) into body (22) firmly.
Lubricate the packings (10) and gland (5). Install
these parts one at a time into the gun body (22). In-
stall the valve stem (14) and packing nut.
. Flip the trigger down and install the screw (8) and
lockwasher. Screw the nipple (20) into the gun
body (22). Install the trigger guard (23) and locknut
(21). Check and adjust the clearance between the
trigger and safety latch before operating the gun.
See below.
Adjusting the Trigger
sure the trigger safety latch makes the gun in-
WARNING
Proper adjustment of the trigger is essential to be
operative when engaged. Improper adjustment
may allow the gun to be triggered, even with the
safety latch engaged, resulting in serious bodily
injury, including fluid injection and splashing in
0.123” (3.18 mm)
the eyes or on the skin.
1. With pressure relieved and the hose disconnected,
engage the trigger safety latch. Check the free play
between the inside end of the trigger (11) and the
tip of the safety latch (A); it should be 0.123 in.
6
(3.18 mm). See Fig 4.
. To adjust, loosen the locknut (9) and adjust the
screw (8) as necessary. Then, without changing the
position of the screw, tighten the locknut. Check
the free play again.
307-260
FREE PLAY
Fig 4
Fig 5
Мих
sure
RD RS SOS К
Я a A
2
a
ocean carat raras
an
Model 210-890, Series C
Includes items 1-27
REF à
*8
NO. PART NO. DESCRIPTION QTY a E
1 101-514 PIN, cotter; 0.06 (1.6 mm) dia; 1.25 in.
(32 mm) long 1
2*t 101-701 BALL, carbide; 0.25 (6.4 mm) dia 1
3* 150-496 PIN, pivot 2
4* 150-497 LINK, pivot pin 2
St 150-501 GLAND, male; piston packing 1
6 150-503 NUT, packing; piston 1
7 150-507 SUPPORT, spring 1
8* 150-512 SCREW, adjusting 1
9* 150-513 LOCKNUT, valve stem adjusting screw 1
10*+ 150-514 V-PACKING, leather 4
11 150-859 TRIGGER 1
12 150-860 NUT, square 1
13 157-441 BODY, valve, lower 1
14 158-080 STEM, valve 1
15 159-080 SPRING, compression 1
16*t 166-660 RETAINER, spring and ball 1
17* 166-969 GASKET, nylon 1
18 220-251 GUARD, tip 1
19 172-525 ADAPTER, increase 3/8 npt to
3/4-16 thd 1
20* 172-526 NIPPLE, pipe; reducing; 7/8-14 x
1/8 npt 1
21 172-524 NUT, hex; 3/4-16 thd
22 206-809 BODY & SEAT ASSY. (upper) 1
23 212-007 GUARD, trigger 1
24 170-239 PLATE 1
25 102-556 RIVET, blind 2
26** 172-479 TAG, warning (not shown) 1
27** 179-960 CARD, wallet warning (not shown) 1
“Recommended “tool box” Spare parts. Keep on hand to reduce
down time.
tThe replacements for these parts are available in Gun Repair
Kit 207-845. Purchase the kit separately.
**Extra warning tags and cards are available at no charge.
#5 SERVICE INFORMATION 2223323:
Added Gun Repair Kit 207-845 to the manual.
“u: HOW TO ORDER REPLACEMENT PARTS #8
== IMPORTANT PH ONE NUMBERS ae 1. To be sure you receive the correct replacement parts, kits or
OS u accessories, always give all of the information requested in
a the chart below.
TO PLACE AN ORDER, contact your Graco distributor, or 2. Check the parts list to identify the correct part number;
call this number to identify the distributor closest to you: do not use the ref. no. when ordering. o
1-800-328-0211 Toll Free 3. Order all parts from your nearest Graco distributor.
FOR TECHNICAL ASSISTANCE, service repair informa- 6 digit
tion or assistance regarding the application of Graco Number Qty Part Description
equipment: 1-800-543-0339 Toll Free |
307-260 7
sate ат АНК длины
р ER О BEER
ie CSC EER DRE SS RS RR
oe ODOUR DD EN ORE SSS SES cS EEE
y
Er oe
Accessories must be purchased separately.
REVERSE-A-CLEAN IV DripLess™ TIP SWIVELS
GUARD 220-422 Use for more flexible gun movement.
5000 psi (350 bar) MAXIMUM WORKING PRESSURE 207-946 1/2 npsm (f) x 3/8 npt(f)
Uses fluid pressure to clear tip clogs. Unique tip guard 5000 psi (350 bar) Max. Working Pressure
resists paint buildup. Spray tip not included; order sepa- 204-940 1/4 npt x 1/4 npsm
rately. 3000 psi (210 bar) Max. Working Pressure
3000 psi (210 bar) MAXIMUM WORKING PRESSURE 168-667 Washer
For spraying inside rocker panels and doors. Tube is 30 in.
102-918 Seal
EXTENSION SPRAY TUBE 206-496 Is
A
»
(760 mm) long and has conical nozzle for spraying unfilled Ss
materials. A Install seal with “М”
168-666 in direction shown
Seal Housing LT —
= —— & TECHNICAL DATA *
206-502 Maximum Working Pressure ............ 4500 psi (310 bar)
o 166-200 466.201 Fluid Valve Orifice Size ............ 0.188 in. (4.78 mm) dia.
_ u _ Length ... cc eee ee eee eee eee nenn 4.5 in. (114 mm)
166-202 162-863 Height... 0... cece ernennen nn nn 7.0 in. (178 mm)
Width ss 1.5 in. (38 mm)
aho Weight .................e.ese. 2.0 Ib (0.9 kg)
} Wetted Parts ................. Zinc-plated steel, alloy steel,
a tungsten carbide, thiokol
171-602 156-454 206-501 impregnated leather, Delrin®
THE GRACO WARRANTY AND DISCLAIMERS
WARRANTY
Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and work-
manship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole
remedy for breach of this warranty, Graco will, for a period of twelve months from the date of sale, repair or replace
any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated
and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tam-
pering, or substitution of non-Graco component parts. Nor shail Graco be liable for malfunction, damage or wear
caused by the incompatibility with Graco equipment of structures, accessories, equipment or materials not sup-
plied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accesso-
ries, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized
Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace
free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. lf
inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a rea-
sonable charge, which charges may include the costs of parts, labor and transportation.
DISCLAIMERS AND LIMITATIONS
THE TERMS OF THIS WARRANTY CONSTITUTE PURCHASER'S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER WARRANTIES (EXPRESS OR IM-
PLIED), INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR APARTICULAR PURPOSE, AND OF ANY NON-CONTRACTUAL LIABILITIES,
INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR STRICT LIABILITY. EVERY FOAM OF LIABILITY FOR DIRECT, SPECIAL OR CONSEQUENTIAL DAM-
AGES OR LOSS IS EXPRESSLY EXCLUDED AND DENIED. IN NO CASE SHALL GRACO'S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION
FOR BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.
EQUIPMENT NOT COVERED BY GRACO WARRANTY
GRACO MAKES NO WARRANTY. AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT
TO ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, put not manufactured
by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
Factory Branches: Atlanta, Chicago, Dallas, Detroit, Los Angeles, West Caldwell (N.J.)
Subsidiary and Affiliate Companies: Canada; England; Switzerland; France; Germany; Hong Kong; Japan; Korea
GRACO INC. PO. BOX 1441 MINNEAPOLIS, MN 55440-1441
PRINTED IN U.S.A. 307-260 8/76 Revised 9/91
8 307-260

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement