Serial Data Communications Module
Serial Data Communications Module
Prices as of April 16, 2014. Check Web site for most current prices.
Specifications
Data
Communications
Module
D2-DCM
Module Type
Modules per CPU
CPUs Supported
Intelligent
7 maximum, any slot except slot 0, CPU base only
D2-240 (firmware V1.8 or later), D2-250-1 and D2-260
RS-232/422 signal levels, DirectNET Master/Slave, K-sequence
or Modbus RTU Slave protocol, Baud rate selectable from 300
baud to 38.4 Kbaud, Odd or No parity, DirectNET HEX or ASCII
mode
Belden 9729 or equivalent (for RS-422)
Communications
$335.00
Recommended Cable
Field Wiring Connector
Internal Power Consumption
25-pin D-shell connector
300 mA maximum at 5 VDC, (supplied by base power supply)
Operating Environment
0ºC to 60ºC (32ºF to 140ºF), 5% to 95% humidity
(non-condensing)
Manufacturer
Koyo Electronics
DCM as additional serial port
The D2-DCM Data Communications
Module is used primarily for three reasons:
• Extra communications port to connect a
PC, operator interface, etc.
• Network interface to DirectNET
• Network interface to a Modbus® network
using the RTU protocol
C - mo r e HMI panel
Extra
communications port
Master/Slave Network
If additional communication ports are
needed, they can easily be added by
installing DCM modules. This allows additional connections of devices, such as
operator interfaces, PCs, etc. Since the
DCM does not require any programming,
you can set the DCM communication
parameters, connect the cables, and start
transferring data. Make sure the device
has a DL205 compatible driver.
DirectNET
network interface
The DCM can be used as a network interface for applications requiring data to be
shared between PLCs, or between PLCs and
an intelligent device such as a host PC. The
DCM connects easily to DirectNET. This
network allows you to upload or download
virtually any type of system data including
Timer/Counter data, I/O information, and
V-memory
information
from
any
DirectLOGIC or compatible PLC. The DCM
allows the DL205 to function as a network
master or network slave.
Connect the DCM to
our MDM-TEL serial modem
(see the Communication
Products section for details
on the modem)
DCM as master
RS232 to RS422
Converter
D2–240 slave
D2–DCM slave
DL–405 CPU (bottom port)
D3–340 slave
Modbus RTU interface
The DCM can be used as a slave station
interface to connect your DL205 system to
a Modbus® network using the Modbus RTU
protocol. The host system must be capable
of issuing the Modbus commands to read
or write the appropriate data. Remember
that the bottom port on the D2-250-1 and
D2-260 CPUs can act as a Modbus master.
Book 1 (14.1)
eD2-54
DL205 PLCs
1 - 80 0 - 633 - 0405
Serial Module for WinPLC and EBC Systems
Prices as of April 16, 2014. Check Web site for most current prices.
Serial
Communications
Module for WinPLCs &
EBCs
H2-SERIO $176.00
H2-SERIO-4 $176.00
Module Type
Approvals
Number of Serial
Ports per Module
Signals
Add serial ports to your WinPLC system
by simply plugging the H2-SERIO or
H2-SERIO-4 modules into the DL205
I/O base. These serial modules are used
exclusively with the WinPLC. The WinPLC
communicates with the H2–SERIO(-4)
module across the DL205 backplane.
3 ports: 2 RS-232 ports (RJ12 jack) and 1
RS-422/485 (5 position terminal strip)
RS-232: CTS, RXD, TXD RTS, GND
RTS transmision delay times: 5, 50, 250 and
RS-232: CTS, RXD, TXD RTS, GND
RTS transmision delay times: 5, 50, 250 and 500 ms
500 ms
RS-422 (4 wire) : TX+, TX-, RX-, RX+, GND
RS-485 (2 wire): Data+, Data-, GND
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
DirectLOGIC
DL205
8
RS-232 ports: Belden 9729 or equivalent
RS-422/RS-485 terminal: 16-28 AWG solid or
stranded conductor (1.5mm2)
Wire strip length: 0.24-0.27 inches (6-7 mm);
Screw torque: 1.7 in-ibs (0.2 Nm)
Protocols Supported
Power Consumption
Baud Rates
Parity
Start and Stop Bits
Operating
Environment
Storage Temperature
Serial ASCII (full-duplex) and Modbus RTU slave
Firmware Note
The H2-EBC requires firmware version v2.1383 or later to support the H2-SERIO or
H2-SERIO-4.
DirectLOGIC
DL305
DirectLOGIC
DL405
Productivity
Controller
Overview
80 mA @ 5 VDC
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Productivity
3000
None, odd, even
1, 2
0 to 60°C (32°F to 140°F), 5% to 95% RH (non-condensing); No corrosive gases, Pollution
level 2; Vibration: MIL STD 810C 514.2; Shock: MIL STD 810C 516.2
-20 to 70°C (-4°F to 158°F)
Universal
Field I/O
Software
C-More
HMI
C-More Micro
HMI
ViewMarq
Industrial
Marquees
The H2-SERIO module has three RS232C ports, while the H2-SERIO-4
module has two RS-232C ports and one
RS-422/485port.
Other HMI
Communications
WinPLC
Up to ten serial ports
on a WinPLC system
The WinPLC has one built-in serial port.
You can add as many as nine additional
serial ports for Think & Do Studio or
Think & Do Live! applications requiring
multiple serial devices, such as barcode
scanners. Connect to just about any
serial device that communicates ASCII
protocol. The H2-SERIO(-4) can also
serve as a Modbus RTU slave.
H2-SERIO
Do-More T1H
PLC
DirectLOGIC
DL105
3
Recommended Cables Belden 9729 or equivalent
Do-More
PLCs Overview
Do-More H2
PLC
cUL Listed, file number E185989
Number of Modules
Supported per
H2-WinPLC-xx
Number of Modules
Supported per
H2-EBC100
Serial I/O modules for
WinPLCs
H2-SERIO-4
Intelligent module for use with H2–WPLC-xx or H2-EBC100
3 ports: all RS-232 (RJ12 jack)
Control Systems
Overview
CLICK PLC
H2-SERIO / H2-SERIO-4 Specifications
H2-SERIO
Company
Information
Appendix
Book 1
H2-SERIO
Processing large
amounts of serial data
with a WinPLC
While the H2-SERIO(-4) module will
support virtually any serial device,
processing large amounts of serial data
will increase the system response time.
This is important to consider when using
multiple H2-SERIO(-4) modules, especially in a WinPLC local base with an
H2-ERM(100) or H2-CTRIO(2).
H2-SERIO-4
Book 1 (14.1)
w w w. a u to m a t i o n d i re c t . c o m / d l 205
DL205 PLCs
eD2-55
Terms and
Conditions
Serial Modules for WinPLC and EBC Systems
Prices as of April 16, 2014. Check Web site for most current prices.
Separate
communications
parameters for each port
All Think & Do PC control software products include advanced string and array
functions that make transmitting, receiving
and manipulating serial data a snap.
Using H2-SERIO(-4)
in a PC-based control
EBC system
Think & Do versions 6.5 and later support
the use of up to eight H2-SERIO(-4)
modules per EBC node in a PC-based
control system. The master must be a PC
running Think & Do 6.5 or later. This does
not apply to a WinPLC system with an
ERM module used for remote I/O.
The Think & Do features described here
for the WinPLC (receiving and manipulating data) also apply to a PC running
the Think & Do software.
6 pin RJ12 Phone
1
Type Jack – both ports
2
3
4
5
6
1
Easy
serial communications
RS-232
6
Use Think & Do software packages to set
baud rate, parity, data bits, and stop bits
for each serial port. Choose from 300
baud to 57.6K baud communication
speeds. Think & Do or Think & Do Live!
allows each port to be designated as a
Modbus slave or a generic serial device.
Each port on the H2–SERIO(-4) module is
capable of full hardware handshaking.
H2-SERIO(-4) Wiring: RS-232
H2-SERIO(-4) RS-232 Pin
Descriptions
0V
CTS
RXD
TXD
RTS
0V
Power (-) connection (GND)
Clear to Send
Receive data (RS-232)
Transmit data (RS-232)
Request to Send
Signal Ground (GND)
H2-SERIO-4 Wiring: RS-422/485
Set DIP switch S2 on the H2-SERIO-4 to:
1. Activate or deactivate the internal 120Ω termination resistor.
2. Select RS-422 or RS-485 operation.
RS-422
SERIO-4
TXD+
TXD(D-) RXD(D+) RXD+
GND
Slave 1
Slave 2
Last Slave
RX+
RXTXTX+
GND
RX+
RXTXTX+
GND
RX+
RXTXTX+
GND
User Supplied
120Ω Termination
Resistor
(H2-SERIO-4 contains an optional 120Ω
termination resistor between RX+ and RX-; use
DIP switch S2 to activate or deactivate resistor.)
RS-485
SERIO-4
TXD+
TXD(D-) RXD(D+) RXD+
GND
Slave 1
Slave 2
Last Slave
DD+
GND
DD+
GND
DD+
GND
(H2-SERIO-4 contains an optional 120Ω
termination resistor between RX+ and RX-; use
DIP switch S2 to activate or deactivate resistor.)
User Supplied
120Ω Termination
Resistor
Book 1 (14.1)
eD2-56
DL205 PLCs
1 - 80 0 - 633 - 0405
Ethernet Communications Modules
Prices as of April 16, 2014. Check Web site for most current prices.
Ethernet
Communications
Module
H2-ECOM100 $301.00
H2-ECOM-F $358.00
can be used to monitor or update the
program in any DirectLOGIC PLC on the
network.
Simple connections
Use Category 5 UTP cables or 62.5/125
ST-style fiber optic cables depending on
the requirements of your application.
Inexpensive UTP cables can be run up to
100 meters between nodes, and fiber
optic cables can be run up to 2,000
meters. Fiber optic cables virtually eliminate electrical noise problems. Use
repeaters to extend distances and expand
the number of nodes.
Our HA-TADP (10/100Base-T) PC network
adapter card and Stride Ethernet switches
are compatible with the ECOM modules.
See the Communications Products section
for information on these items.
ECOM starter kit
Overview
Ethernet Communications Modules offer
features such as:
• High-speed peer-to-peer networking
of PLCs
• Fast updates with DirectSOFT Programming
Software
• High-performance access for Human
Machine Interface (HMI), ERP, MES or
other Windows-based software
• Industry standard Modbus TCP
Client/Server Protocol (H2-ECOM100)
• Free SDK for custom drivers
• Easy setup
The Ethernet Communication (ECOM)
Modules represent a price breakthrough
for high-speed peer-to-peer networking of
PLCs. No longer are you forced to designate a single PLC to be the network
master. Any PLC can initiate communications with any other PLC. Link your PLCs
with PCs using industry standard Modbus
TCP protocol connected through standard
cables, hubs, and repeaters. Or, use our
Direct I/O Server to link to your
KEPD
favorite HMI/SCADA, data historian, MES
or ERP software to DirectLOGIC PLCs. Our
Direct HMI and our DataWorx
LookoutD
data collection software include ECOM
drivers. DirectSOFT Programming Software
The H2-ECOM-START gives you everything you need to make your first Ethernet
network simple to build. It contains an
H2-ECOM100 module and instruction
manual, a network adapter card (PCI) for
your PC, a crossover cable, and a
Software Product Showcase Demo CD.
The CD contains demo versions of our
software products that support the ECOM
Modules. See the Software Products
section for information on the available
software packages.
H2-ECOM100 IBox
communications
instructions
Over 25 Communications IBox instructions are available when using the
H2-ECOM100 with a DL250-1 or DL260
PLC and DirectSOFT5 programming software. These easy-to-use instructions allow
you to:
• Enable/disable module DHCP
• Read/write module IP, Gateway and
Subnet Mask addresses
• Read/write module ID, Name and
Description
• Send E-mail messages
• Read/Write PLC memory to networked
Hx-ECOM100 modules
• Read/Write PLC memory to networked
Hx-ECOM(-F) modules
See the following page for example
Communications IBox instructions.
Company
Information
Control Systems
Overview
CLICK PLC
Do-More
PLCs Overview
Do-More H2
PLC
Do-More T1H
PLC
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
DirectLOGIC
DL105
DirectLOGIC
DL205
DirectLOGIC
DL305
DirectLOGIC
DL405
Productivity
Controller
Overview
Productivity
3000
The
H2-ECOM100 supports the
Industry Standard Modbus TCP
Client/Server Protocol
Universal
Field I/O
Software
C-More
HMI
C-More Micro
HMI
ViewMarq
Industrial
Marquees
Other HMI
Message is sent out
of port only
connected to device
Communications
Message in
from a device
Appendix
Book 1
Terms and
Conditions
See the Communications
section for details on
Ethernet Switches
Specifications
H2-ECOM100
H2-ECOM-F
Communications
Data Transfer Rate
Link Distance
Ethernet Port
10/100Base-T Ethernet
10Base-FL Ethernet
100 Mbps max.
10 Mbps max.
100 meters (328 ft)
2,000 meters (6,560 ft)
RJ45
ST-style fiber optic
Ethernet Protocols
TCP/IP, IPX, Modbus TCP,
DHCP, HTML configuration
TCP/IP, IPX
Power Consumption
Manufacturer
300 mA @ 5 VDC
640 mA @ 5 VDC
Host Automation Products, L.L.C.
Book 1 (14.1)
w w w. a u to m a t i o n d i re c t . c o m / d l 205
DL205 PLCs
eD2-57
Ethernet Communications Modules
Prices as of April 16, 2014. Check Web site for most current prices.
Modbus TCP support
The H2-ECOM100 supports the industry
standard Modbus TCP Client/Server
protocol in addition to the standard IP and
IPX protocols. This allows the DL205 PLC
with an H2-ECOM100 module to serve
as a client (master) or as a server (slave)
on a Modbus TCP Ethernet network. The
H2-ECOM100 can actively issue Modbus
commands to other nodes or devices on
the Modbus TCP network or simply
respond to connected Modbus TCP
clients.
PLC-to-PLC
communications
PLC-to-PLC or PLC to a Modbus TCP
device communications can be accomplished using standard Read from Network
(RX) and Write to Network (WX) instructions (DL240/250-1/260, all H2 series
ECOMs and all DirectSOFT versions). If
you’re using our DirectSOFT5 programming software, a DL250-1 or DL260 PLC
and an H2-ECOM100, you can use fill-inthe-blank IBox instructions to simplify your
communications programming. The H2ECOM100 supports the ECOM100
Configuration IBox for use with the ECRX
and ECWX IBox instructions to read/write
to other ECOM(100)s. All H2 series
ECOM modules support the NETCFG
Configuration IBox for use with the NETRX
and NETWX IBox instructions to read/write
to other ECOM modules (remember
DL250-1/260 and DSOFT5 required).
The Communications IBox instructions
execute with built-in interlocking to greatly
simplify communications programming.
H2-ECOM100 has
e-mail capability!
The
H2-ECOM100
Send
EMail
(ECEMAIL) IBox instruction allows the
module to behave as an e-mail client and
send an SMTP request to your SMTP
Server to send a specified e-mail message
to the e-mail addresses in the in IBox’s
To: field. The Body: field allows you to
embed real-time data in your e-mail
message. The DL50-1/260 CPU and
DirectSOFT5 are required to use the IBox
instructions.
Modbus TCP communications architecture
ECOM100 Configuration IBox
ECOM100 Read Network IBox
NetEdit3 software
NetEdit3 Software ships free with the
ECOM User Manual. Use NetEdit3 to
configure the ECOM modules for your
network. Flexible addressing allows you to
use your choice of protocols and identifying methods. Assign each module a
number or a name or both. You don’t
have to use an IP address, but you can if
it’s necessary for your network. NetEdit3
uses two protocols for PC-to-PLC communications: IPX and TCP/IP. The NetEdit3
screen displays all identifiers and troubleshooting information for each module
on the network. You can use NetEdit3 to
adjust parameters for PLC-to-PLC
communications by clicking on Advanced
Settings. The network identifiers can also
DirectSOFT
be
changed
from
Programming Software.
Choose your slot
ECOM100 Send EMail IBox
The ECOM modules plug into any I/O
slot (excluding slot 0) of any local DL205
I/O base. The module maintains identification data, descriptive information, and
communication parameters for PLC-toPLC communications in flash memory.
Disconnect power before installing or
removing any PLC module.
205
C PU
Slot0
Slot1
Slot2
Slot3
Slot4
N o!
Note: Use D2-240, D2-250, D2-250-1 or D2-260 CPUs
with the ECOM modules. The D2-230 CPU and D2-CM
bases do not support the ECOM modules.
Book 1 (14.1)
eD2-58
DL205 PLCs
1 - 80 0 - 633 - 0405
Prices as of April 16, 2014. Check Web site for most current prices.
Power Requirements
These charts help
determine your power
requirements
This section shows the amount of power
supplied by each of the base power
supplies and the amount of power
consumed by each DL205 device. The
Power Consumed charts list how much
INTERNAL power from each power source
is required for the DL205 devices. Use this
information when calculating the power
budget for your system.
In addition to the internal power sources,
the DL205 bases offer a 24 VDC auxiliary
power supply with external power connections. This auxiliary power supply can
power external devices.
Use ZIPLinks to reduce
power requirements
If your application requires a lot of relay
outputs, consider using the ZIPLink AC or
DC relay output modules. These modules
can switch high current (10A) loads
without putting a load on your base power
budget. Refer to the Terminal Blocks and
Wiring Solutions section in this catalog for
more information.
This logo is placed next to the I/O
modules that are supported by the ZIPLink
connection systems. See the I/O module
specifications at the end of this section.
Device
D2-03B-1
Operator Interface
DV-1000
150
0
C-more MicroGraphic
210
0
5V(mA) 24V Auxiliary
Bases
D2-06BDC1-1
$194.00
2600
None
None
D2-06BDC2-1
$184.00
2600
300
D2-04B-1
300
D2-09B-1
$220.00
2600
300
D2-04BDC1-1 $171.00 2600
None
D2-09BDC1-1
$238.00
2600
None
D2-06B-1
300
D2-09BDC2-1
$238.00
2600
300
$132.00 2600
$143.00 2600
$176.00 2600
Power Consumed
Power Consumed
Device
5V(mA)
24V Auxiliary
Device
5V(mA)
24V Auxiliary
Analog Modules
CPUs
D2-230
120
0
F2-04AD-1
100
5
D2-240
120
0
F2-04AD-2
110
5
D2-250-1
330
0
F2-08AD-1
100
5
D2-260
330
0
F2-08AD-2
100
5
H2-WPLC*-**
680
0
F2-02DA-1
40
60 (note 1)
F2-02DA-1L
40
70 @ 12V (note 1)
0
F2-02DA-2
40
60
40
70 @ 12V
DC Input Modules
D2-08ND3
50
D2-16ND3-2
100
0
F2-02DA-2L
D2-32ND3
25
0
D2-32ND3-2
25
0
F2-02DAS-1
F2-02DAS-2
100
100
50 / channel
60 / channel
F2-08DA-1
30
50 (note 1)
F2-08DA-2
60
140
F2-4AD2DA
60
80 (note 1)
F2-8AD4DA-1
35
100 (note 1)
F2-8AD4DA-2
35
80 (note 1)
F2-04RTD
90
0
F2-04THM
110
60
AC Input Modules
D2-08NA-1
D2-08NA-2
D2-16NA
50
100
100
0
0
0
Input Simulator Module
F2-08SIM
50
0
DC Output Modules
D2-04TD1
60
20
D2-08TD1
100
0
D2-08TD2
100
0
200
200
80
0
F2-16TD1P
70
50
F2-16TD2P
70
50
D2-32TD2
24V Auxiliary
Price
D2-03BDC1-1 $150.00 2600
D2-32TD1
5V(mA)
Device
300
D2-16TD2-2
Device
Power Supplied
Price 5V(mA) 24V Auxiliary
Bases
D2-16TD1-2
Power Consumed
HERE
350
350
0
0
AC Output Modules
D2-08TA
250
0
F2-08TA
250
0
D2-12TA
350
0
Relay Output Modules
D2-04TRS
250
0
D2-08TR
250
0
F2-08TR(S)
670
0
D2-12TR
450
0
Combination In/Out Module
D2-08CDR
200
0
Specialty Modules
D2-CTRINT
50*
0
D2-CM / D2-EM
100/130
0
H2-CTRIO
400
0
H2-CTRIO2
275
0
D2-DCM
300
0
F2-DEVNETS
160
0
F2-SDS-1
160
0
H2-PBC
530
0
H2-EBC100
300
0
H2-EBC-F
640
0
H2-ECOM100
300
0
H2-ECOM-F
640
0
F2-CP128
235
0
H2-ERM100, (-F)
300, (-F: 450)
0
D2-RMSM
200
0
D2-RSSS
150
0
Remote I/O
Programming Devices
D2-HPP
200
0
*requires external 5VDC for outputs
Note 1: Add an additional 20 mA per output loop.
Book 1 (14.1)
eD2-46
DL205 PLCs
1 - 80 0 - 633 - 0405
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement