NewAge Products 85796 White Particle Board Shaker Stock Assembled Base 18-Piece Kitchen Cabinet Set (94.77 in. x 84 in. x 100.76 in.) Instructions
Advertisement
Advertisement
!
Home Cabinets
INSTALLATION GUIDE
Warning: Excessive weight hazard!
Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury.
STOP
ATTENTION
:
Is your Home Cabinet damaged?
Need help or spare parts? For fastest service, contact NewAge Products at 1-877-306-8930; or [email protected].
Do not return to the retailer.
IM-HKC.01A-01 REV1.1
Index
Cabinets purchased with Doors and Drawer front panels
Measuring and Marking your Space
Removal and Installation of Doors
Index
Removal and Installation of Drawers
Installation of Drawer Front Panels
Installation of Drawer Front Panels
Adjusting the Drawer front panel
Installation of Glass Shelves on Wall Cabinets with Glass Doors
Installation of Feet for Base Cabinets
Blind Corner Cabinet - Filler Panel Installation
Installation of Blind Corner Cabinet
Wall Rail Installation for Wall Cabinets
Installing the Above Fridge Cabinet
Installing the Wall Cabinet Side Panels
Installing the Wall cabinet Skirting
Installing the Base Cabinet Side Panels
Index
Installing the U shaped layout
Additional Acc essories off ered by NewAge
SPARE PARTS - BASE CABINET with DOORS
SPARE PARTS - SPLIT DRAWER and DOORS
SPARE PARTS - STANDARD WALL CABINETS
SPARE PARTS - CORNER WALL CABINET
SPARE PARTS - GLASS DOOR WALL CABINETS
DOOR AND DRAWER REFERENCE TABLE
ATTENTION :
Installing a kitchen is considered a major project, and man y diff erent skills are needed to be able complete the project correctly. There are many tools needed to make the process smoother, and NewAge recommends using a professional kitchen installer for the best overall installation experience.
It is recommended to book your installer to begin work one week after receiving the products to avoid any delay in installation, due to missing/damage products during the transit.
Unpacking
• Begin by placing the package on a covered flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose / recycle all packaging materials.
• Verify all the contents in the box and gather the required tools. See “Tools Needed” in the page 7
.
5
Product Inspection
• Check to see all parts are received as per the order placed.
• Contact NewAge Products at 1-877-306-8930; for any missing parts.
• Inspect the products for any damages before starting the installation.
• Go through the installation instructions carefully before starting the installation.
Home Cabinets and Accessories
Base Cabinets Wall Cabinets Side Panels Crown Molding
Toe Kick Skirting Led Lights Shelves
Doors
6
Handles Sink Granite Countertop
Tools Needed
Hammer Pry Bar Straight Edge Phillips Bit Level
Tape Measure Pencil Miter Box Drill 5/32” Drill Bit
Saw C - Clamps Wood Shims Stud Finder Safety Glasses
Hacksaw
Optional Tools
Tin Snips Extended Philips Driver #2
7
Compound Mitre Saw Circular Saw Vacuum Cleaner
Hardware
Hardware required for each cabinet comes in a separate hardware box attached inside the respective cabinets.
If you purchase your cabinets without doors or drawers, additional hardware required for installing the doors/drawers are also included in the hardware box.
Adjustable leg
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm
Chip board screw for
Cabinets
Ø4mm X 30mm
Lag Screw
Ø6mm X 70mm
Molly Bolts
HM 6x37 S
Door Hinge 155° Door Hinge 110° Door Hinge 95°
Drawer support bars
(only for middle and bottom drawers)
Support bar locks
Drawer Stabilizer
(Only for 36”
Cabinet drawers)
Drawer Front
Connector
8
Glass Shelf Clips Toe kick clips
9
Hardware for:
Cabinets purchased with Doors and Drawer front panels
Base Cabinet with Doors / Drawers
Hardware
Adjustable legs
Flat head chipboard screws
Lag screws
Toekick Clips
Chipboard screws for
Toekick clips
Specifica tions Quantity
4
Ø4mm X 30mm
8
Ø6mm X 70mm
Ø3.5mm X
16mm
2
2
4
Wall Cabinet with Wooden Doors
Hardware
Mounting Bracket and Covers
Flat head chipboard screws
Molly Bolts
Lag screws
Specifica tions Quantity
2
Ø4mm X 30mm
HM 6x37 S
Ø6mm X 70mm
8
2
3
Wall Cabinet with Glass Doors
Hardware
Mounting Bracket and Covers
Flat head chipboard screws
Molly Bolts
Lag screws
Shelf Pin
Glass Shelf Clip
Specifica tions Quantity
2
Ø4mm X 30mm
HM 6x37 S
Ø6mm X 70mm
8
2
3
8
8
Corner Wall Cabinet
Hardware
Mounting Bracket and Covers
Flat head chipboard screws
Molly Bolts for dry wall
Lag screws
Cover for Mini Fix
Specifica tions Quantity
3
Ø4mm X 30mm
HM 6x37 S
Ø6mm X 70mm
8
4
5
4
Above Fridge Cabinet
Hardware
Flat head chipboard screws
Molly Bolts for dry wall
Lag screws
Specifica tions Quantity
Ø4mm X 30mm 8
HM 6x37 S
Ø6mm X 70mm
2
3
Hardware for:
Cabinet frames
Base Cabinet for Doors
Hardware Specifica tions Quantity
Purchased with Doors
Adjustable legs 4
Ø4mm X 30mm
8
Flat head chipboard screws
Lag screws
Toekick Clips
Chipboard screws for
Toekick clips
Ø6mm X 70mm
Ø3.5mm X
16mm
2
2
4
Door Hinges 2 (Single door) or
4 (Double door)
Base Cabinet for Drawers
Hardware Specifica tions Quantity
Purchased with Drawer Fronts
Adjustable legs 4
Flat head chipboard screws
Lag screws
Toekick Clips
Chipboard screws for
Toekick clips
Ø4mm X 30mm
Ø6mm X 70mm
Ø3.5mm X
16mm
8
2
2
4
Drawer Front
Connectors
6
Drawer Stabilizer
(only for 36” Cabinet)
Drawer support bars
Drawer support bars locks
Chipboard screws for
Drawer Stabilizer
Ø4X15.5L
3
8
8
6
Blind Corner Cabinet
Hardware Specifica tions Quantity
Purchased with Doors
Adjustable legs 4
Flat head chipboard screws
Lag screws
Toekick Clips
Chipboard screws for
Toekick clips
Ø4mm X 30mm
Ø6mm X 70mm
Ø3.5mm X
16mm
8
2
2
4
Door Hinges 2
10
Wall Cabinet
Hardware Specifica tions Quantity
Purchased with Doors
Mounting Bracket and Covers
Ø4mm X 30mm
2
8 Flat head chipboard screws
Molly Bolts for dry wall
Lag screws
Door Hinges
Shelf Pin (only for glass door cabinet)
HM 6x37 S
Ø6mm X 70mm
2
3
2 (Single door) or
4 (Double door)
8
8 Glass Shelf Clip
(only for glass door cabinet)
Base Cabinet for Drawers and Doors
Hardware Specifica tions Quantity
Purchased with doors
Adjustable legs 4
Flat head chipboard screws
Ø4mm X 30mm
6
Lag screws
Toekick Clips
Chipboard screws for
Toekick clips
Ø6mm X 70mm
Ø3.5mm X
16mm
2
2
4
Door Hinges 2 (Single door) or
4 (Double door)
Drawer Front
Connectors
Drawer Stabilizer
(only for 36” Cabinet)
Chipboard screws for
Drawer Stabilizer
Ø4X15.5L
2
1
2
Corner Wall Cabinet
Hardware Specifica tions Quantity
Purchased with doors
Mounting Bracket and Covers
Ø4mm X 30mm
3
8 Flat head chipboard screws
Molly Bolts for dry wall
Lag screws
Door Hinges
HM 6x37 S
Ø6mm X 70mm
4
5
4
Hardware for:
Cabinets Frames
Above Fridge Cabinet
Hardware Specifica tions Quantity
Purchased with Doors
Ø4mm X 30mm 8 Flat head chipboard screws
Molly Bolts for dry wall
Lag screws
Door Hinges
HM 6x37 S
Ø6mm X 70mm
2
3
4
Pantry Cabinet
Hardware Specifica tions Quantity
Purchased with Doors
Adjustable legs 4
Flat head chipboard screws
Lag screws
Toekick Clips
Chipboard screws for
Toekick clips
Ø4mm X 30mm
Ø6mm X 70mm
Ø3.5mm X
16mm
8
2
2
4
Door Hinges 2
Kitchen Island
Hardware
Adjustable leg base
Adjustable leg
Chipboard screws
Specifica tions Quantity
4
4
Φ3.5Χ 16 16
Hardware
Accessories
Crown Molding
Hardware
Chipboard screws
Specs
Ø3.5mm X
35mm
Quantity
10
Skirts
Hardware
Chipboard screws
Specs
Ø3.5mm X
35mm
Quantity
10
11
Room Preparation
ATTENTION
:
NewAge recommends using a professional kitchen installer to prepare and install kitchen cabinets.
NOTE
:
If you are unfamiliar or unsure of how to handle utility connections, hav e a qualified professional perform these duties.
Before you begin
• Shut off all existing water, power and utility lines.
• Remove existing appliances (stove, oven, refrigeration, sink, and dishwasher). It is best to move these out of the room for easier access to the work area while the remodeling is being done.
• Remove old cabinets and countertops.
• Remove any moldings from the walls where cabinets are to be installed.
Measuring and Marking your Space
A
B
B
B
E
B
D
C
It is very important to measure and understand your room space for planning your installation.
Use a tape measure and a pencil to measure and identify the following:
A. Height of the room from the floor to the ceiling.
B. Width of the room wall to wall / wall to door.
C. Height from the floor / Ceiling to any windows to ensure the cabinets fit.
D. Location of any service points for plumbing,electrical and any other use.
E. Any other permanent fixtures like pillars.
12
Room Preparation
Preparing your Room
• Locate the uneven areas to adjust the cabinets in order to make the installation plumb, true and square.
Plumb Line
Corner is out of plumb
2 3/8”
30” or 36”
Mark top line for wall cabinets
Refernce line for wall rails
Mark bottom line for wall cabinets
54”
1.25” for Granitetop
Base level line
Mark first line at
34.75 inches for cabinets.
36”
1.25”
Plumb Line
High points on floor.
• Using a carpenter’s level, find the high point of the floor.
• Check all around the room within 24” of the wall where base cabinets will be attached.
• From the high point, mark a level horizontal line using a straight edge, on the walls where the cabinets will be attached. This will be called the base level line.
• From the base level line, measure up 34 3/4” and mark another level horizontal line for the base cabinets.
• Add 1-1/4” for a standard NewAge countertops (if you are using a custom countertop, measure the thickness accordingly) and 18 inches for a standard backsplash. Mark the bottom line for wall cabinets at this 54-inches from the base line which will serve as a guide for hanging the cabinets.
• Mark the top line for wall cabinets at 30” or 36” (according to the height of wall cabinets selected) from the bottom line for wall cabinets.
• Mark a reference line 2 3/8” below the measured top line of the wall cabinet. This Line acts as a reference to install suspension rails on the wall.
13
Room Preparation
• Use a stud finder to locate the wall studs. The wall studs are crucial to properly support the weight of the cabinets.
Locate Wall Studs
• Using a carpenter’s level, check the walls for uneven spots. Wall unevenness can cause cabinets to be misaligned resulting in racking or misalignment of the doors and drawer fronts. At the point where these uneven spots interfere, high spots should be removed by scraping and sanding off excess plaster or sheet rock. Low spots should be shimmed with pieces of wood shims.
• Mark the outlines of all the cabinets on the wall to check actual cabinet dimensions against your layout to confirm that the room design used will work.
• Mark down all plumbing and other utilities. Check that everything fits with the measurements from your plan and your electricity, water, gas and ventilation connections are where you want them to be.
36” Wall Cabinet
24”
Glass Door
Wall Cabinet
Corner
Wall
Cabinet
Above
Microwave
Cabinet
24”
Wall Cabinet
Above
Fridge Cabinet
36” Sink Cabinet
24” Cabinet
18”
Base
Cabinet
Blind
Corner
Cabinet
Stove
24”
3- Drawer
Cabinet
Fridge
Pantry Cabinet
Example of cabinets outlined on wall
14
Installation Layout Options
Corner Layout Linear Layout
U - Shaped Layout
Island Layout
15
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
16
Installation Overview
The section gives you an overview of cabinets installation process. Refer to the corresponding sections in this install guide for step by step process.
Remove doors and drawers of all the cabinets and store in a safe area where they cannot get damaged during installation
Install leveling legs to all the base cabinets. Make sure to install on the correct side for single door cabinets.
Note
:
It is recommended t o install all base cabinets first . If you are installating a corner layout start with the Blind Corner Cabinet.
Install the blindcorner cabinet, 9” off set from the wall.
Install base cabinets according to the planned layout.
Install all wall cabinets according to the planned layout.
60mm (2.36”)
Installation Overview
Install Side panels.
Install Skirting and Crown moldings.
Install Toekicks to all base cabinets.
Install doors and drawers of all the cabinets.
Install Handles for all the cabinets.
Install all other accessories purchased with the cabinets.
17
Removal and Installation of Doors
Installing the Door Hinges
If you’ve purchased custom color or Espresso doors your cabinet will arrive without the doors attached. You will be required to first, pre-install the hinges onto the doors, then attach the doors after installing all cabinets according to the planned layout.
Remove the protective film on the doors and drawer fronts before the installation.
1 Locate the pre-drilled holes on the back edge of the doors.
2
Fix the Hinges in position aligning with the holes. Tighten the pre-installed screws on the hinges.
18
Removal and Installation of Doors
Blind Corner Cabinet
If you purchase your cabinets with doors, remove doors of all the cabinets before installation. Install doors after installing all cabinets according to the planned layout.
1 Open the cabinet door and identify the door hinges.
2
Press the release clip on the front and pull the hinge clips outwards to release the door from cabinet.
3
Remove the door.
4 Install the door and press the hinge onto the hinge plate.
19
Removal and Installation of Doors
Base and Wall Cabinets
If you purchase your cabinets with doors, remove doors of all the cabinets before installation. Install doors after installing all cabinets according to planned layout.
1 Open the cabinet doors and identify the door hinges for each door.
2
Press the release clip on the front and pull the hinge clips outwards to release the door from cabinet.
3
Remove the door.
4 Install the door and press the hinge onto the hinge plate.
20
Removal and Installation of Doors
Pantry cabinet
If you purchase your cabinets with doors, remove doors of all the cabinets before installation. Install doors after installing all cabinets according to planned layout.
1 Open the cabinet doors and identify the door hinges for each door.
2
Press the release clip on the front and pull the hinge clips outwards to release the door from cabinet.
3
Remove the door.
4 Install the door and press the hinge onto the hinge plate.
21
Removal and Installation of Doors
Adjusting the Door Hinges
Note:
After the cabinets & doors have been installed it is up to the customers to make the adjustments to the hinges to ensure that the doors and drawers are all leveled.
Rotate the screws on the hinges using a screwdriver to adjust the position of the doors after installation.
Wall and Base cabinets
Blind corner cabinet
Pantry cabinet
22
Soft Close
Spring Tension
Removal and Installation of Drawers
It is recommended to remove all cabinet drawers before installation.
1
Slide out the drawer.
2 Remove cover on the both side of the drawer.
3 Pull the clips up from both sides of the drawer and slide the drawer off the slides.
4 Place the drawer in position over the rails and push it in to install.
23
Removal and Installation of Drawers
5
Place the drawer in position over the rails and push it in to install. Re-install cover plate on both sides of drawer.
24
Installation of Drawer Front Panels
Top Drawer
If you’ve purchased cabinets with doors/drawer front separately, you will be required to install the drawer front connector onto the drawers.
1
Take the Top drawer front panel and fix the drawer stabilizer(36” Drawer only) into two holes at the centre on back of the panel.Tighten the screws using a philips screwdriver.
2
Fix the dawer front connectors into the holes at both ends of the panel. Tighten the screws using a philips screwdriver.
Only for 36” Drawer
3
Push the top drawer front panel into the top drawer and make sure the drawer front connectors are locked into the drawer properly.
4
Open the drawer and drill in two Ø4mm
X15mm screws through the holes on the drawer stabilizer from the bottom.
25
Installation of Drawer Front Panels
Middle and Bottom Drawers
1
Take the Middle drawer front panel and fix the drawer stabilizer(36in Drawer only) into the two holes at the centre on back of the panel.Tighten the screws using a philips screwdriver.
2
Fix the dawer front connectors into the bottom two holes at both ends of the panel. Tighten the screws using a philips screwdriver.
3
Fix four support bar locks into the top four holes at both corners of the panel. Tighten the screws on the locks using a philips screwdriver.
4
Push the middle drawer front panel into the middle drawer and make sure the drawer front connectors are locked into the drawer properly.
26
Installation of Drawer Front Panels
Middle and Bottom Drawers
5
Open the drawer and drill in two Ø4mm
X15.5L screws through the holes on the drawer stabilizer from the bottom.
6
Take a drawer support bar and slide the cover inwards.
7
Fix the support bar to the drawer by pusing it into the slots on the back of the drawer and sliding the support pin on the front into the support bar locks.
27
Installation of Drawer Front Panels
Middle and Bottom Drawers
8
Slide the cover on the support bar outwards.
9
Install all four darwer support bars similarly.
10
Similarly install all support bars for the bottom drawer. Follow steps 1 to 9.
28
Installation of Drawer Front Panels
Adjusting the Drawer front panel
Note: Adjust the drawers prior to using the kitchen.
Adjust the drawer front panel downwards by rotating the screw (A) counter clockwise on both sides of the drawer.
A
Adjust the drawer front panel upwards by rotating the screw (A) clockwise on both sides of the drawer.
A
Adjust the drawer front panel to the right by rotating the screw (B) counter clockwise.
B
Adjust the drawer front panel to the left by rotating the screw (B) clockwise.
B
Remove the drawer front panel by rotating the screw(C) counter clockwise.
C
29
Adjusting the Wood Shelves
All Wooden shelves are delivered pre-installed with the cabinets. You can adjust the shelves at different heights.
1
Each shelf is supported by four support dowel pins which goes under the support housing. Support housing can be locked to fix the position of shelves.
2
Slide the shelf lock outwards at all corners on the bottom of the shelf.
Cabinet wall
Shelf
Cabinet wall
Shelf
3
Lift the shelf upwards from the support dowel pins and remove the shelf out from the cabinet.
4
Support dowel pins can be removed and installed at different holes on the carcass to install shelves at different heights.
5 Install shelf by placing the shelf resting on the support dowel pins.
6 Slide the shelf lock inwards at all corners on the bottom to lock the shelf.
30
Installation of Glass Shelves on Wall Cabinets with Glass Doors
All Glass shelves for the Glass door cabinets are delivered uninstalled with the cabinets. Install
Glass shelves after installation of the cabinets.
1
Four shelf support brackets for each shelf is needed for the support. Pull the lock downwards and move the top portion of the support bracket.
2 Install support brackets into the holes on the cabinet carcass.
Locked Unlocked
3 Slide in the glass shelf through the support brackets.
4
Press the top portion the support bracket downwards and push the lock upwards for locking the shelf in position.
Push to lock
5 Follow steps 1 to 4 for installing the other glass shelf.
31
Installation of Feet for Base Cabinets
ATTENTION: Once feet are intalled removing them will cause damage to the cabinets.
Install adjustable feet for all base cabinets before beginning the installation process. The adjustable legs are packaged in a hardware box inside the cabinet
1 Remove the doors of all cabinets. Refer to
for removal of doors.
2
Flip the cabinets upside down on a protective soft surface and locate the holes at each corner of the cabinet.
Ensure to fix legs on the correct side based on door opening.
3
Two or more people are required to lift/move cabinets into place.
Four adjustable legs for each cabinets are provided in the hardware box. Remove leveling leg base from the legs before installation. The leveling legs have a 3/4” height adjustability.
Leg base
Leg post
32
Installation of Feet for Base Cabinets
4
Push and fit the leveling leg base into one of the holes and making sure that the tab is overlapping the side panel of frame.
5
Insert the leg post into the leg base and psuh it in to lock the entire leg assembly into place. Removing leg post after locking will damage cabinet.
6 Repeat the step 2 to 4 to install all the leveling legs. Ensure all legs are in the lowest position.
Carefully lift up and flip the cabinet.
33
Installation of Feet for Base Cabinets
7 Adjust the legs to level the cabinet.
Max. 3/4” adjustable
34
Corner Layout Installation
Blind Corner Cabinet - Filler Panel Installation
Note: When installing a corner layout, it is recommended to start the cabinets installation with blind corner cabinet. Install the L - filler panel provided inside the blind corner cabinet before installing it to the wall.
1
Parts required
1
Take the L-shaped filler piece which comes with the blind corner cabinet and identify two pilot holes provided on the cabinet.
Ø4 mm X 30 mm
Chipboard Screws
2
L-Shaped
Filler Piece Drill
C-clamp the L - filler piece into position ensuring the top and bottom are flush with the cabinet.
3
Take two Ø4mm X30mm chip board screws from the hardware box and screw the L-fillet piece to the cabinet from the inside using the pilot holes. Ensure not to over screw.
35
Do not screw-in L-Panel from the outside.
Corner Layout Installation
Installation of Blind Corner Cabinet
Note: It is recommended to start installing the corner base cabinet first and install other wall cabinets on the both sides.
Install the blindcorner cabinet, 9” offset from the wall.
Placing a level on the cabinet front to back, level the cabinet by rotating the feet. Repeat this step with the level left to right. The cabinet should be level along all edges.
9”
3
Align the adjacent cabinet (with doors/ drawers installed) next to blind corner cabinet.
4
Align the cabinets, such that the filler piece on the blind corner cabinet is flush with the doors of the adjacent cabinet.
36
Corner Layout Installation
Installation of Base Cabinets
5
Once the adjacent cabinet has been aligned with the corner cabinet, level this cabinet front to back and left to right by adjusting the leveling legs.
6
Mark a position for pilot hole at the vertical center of back panel, aligned with the wall studs.
7
Referencing the pre marked location, drill pilot hole using a 5/32” in drill bit. Screw in the Corner and Adjacent Cabinets into the wall studs using the Ø6mm x70mm Lag screws provided.
37
Corner Layout Installation
Installation of Base Cabinets
8 Referencing your design layout, align the next cabinet to be installed accordingly.
9
Placing a level on the cabinet front to back, level the cabinet by rotating the feet. Repeat this step with the level left to right. The cabinet should be level along all edges and aligned with the adjacent cabinet.
2”
10
Fix both cabinets together to prevent movement using a c-clamp. Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach cabinets together.
2”
2”
2”
2”
2”
11
Mark a position for pilot hole at the vertical center of the back panel, aligned with the wall stud.
Referencing the pre marked locations, drill pilot holes into each wall stud using a
5/32” drill bit. Screw in the cabinet to the wall stud using the Ø6x70mm Lag screws provided.
38
2”
2”
Corner Layout Installation
Installation of Base Cabinets
13
Similarly install other cabinets according to the layout, secure cabinets each other and secure them to the wall.
2”
Two or more people are required to lift/move cabinets into place.
3/4” 3/4”
39
Wall Rail Installation for Wall Cabinets
All wall cabinets except the above fridge cabinet needs wall hanger rails as a support to hang on the wall. Install wall hanger rails according to the layout marked on the wall.
Use lag screws to secure rails to the wall. It is recommended to install a Molly bolt if any end of the the rail is between the wall studs.
When installing wall hangers rails on the wall, it is important to understand the profile of the rail. Always make sure the tapered profile of the wall rail is pointed downwards.
Tapered profile
Mark the required length of wall hanging rails as per your planned layout.
Cut the rails to 3/4” lesser than the marked length using a hacksaw. (Rail can also be bent/ broke by hand at marked lines along rail.)
40
Wall Rail Installation for Wall Cabinets
3
Mark a horizontal reference line 2 3/8 “ (60mm)below the measured top line of the wall cabient. Align the center of the hanging rail on this line and mark the holes of wall rail on the wall studs.
Wall Studs
2 3/8”
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
Reference line for
Wall hanger rails
4 Pre drill the markings on wall studs using a
3/32” drill bit.
5 Fix the rails to the wall using 6x70mm lag
Wall Studs
Wall Studs
Reference line for
Wall hanger rails
41
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
60mm (2.36”)
Wall Rail Installation for Wall Cabinets
6
Use a level to check that each rail is level.
7 Use shims if necessary at the uneven surfaces of the wall.
Level
Wall Studs
Top Line for Wall
Cabinets
Top Line for Wall
Cabinets
Wall Studs
Note
:
It is recommended to install a Molly bolt if any end of the the rail is between the wall studs.
8
Mark the hole at the end of the rail to the wall.
2 3/8”
A
Reference line for
Wall hanger rails
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
42
Wall Studs
Wall Rail Installation for Wall Cabinets
9
Wall Studs
Pre drill the marking on wall using a 8mm drill bit.
10
Install the mollybolt into the hole using a hammer / rubber mallet.
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
Wall Studs
Wall Studs
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
Reference line for
Wall hanger rails
11 Remove the screw from the Molly bolt. 12
Install the screw after securing rail to the wall.
Reference line for
Wall hanger rails
60mm (2.36”)
Reference line for
Wall hanger rails
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
Top Line for Wall Cabinets
(84” or 90” from the base level line measured and marked on page 9.)
43
Wall Cabinets Installation
Note: It is recommended to start installing the corner wall cabinet first and install other wall cabinets on the both sides.
1
Remove doors of all cabinets before
installation. Refer to page 19-21 for
removal of doors.
2
Locate the three wall hanging brackets on the corner wall cabinet. These will be used for hooking onto the hanging rail.
3
Fully extend all the wall hanging brackets by rotating the screw “A“ counter clockwise. Use the extended philips bit for best results.
4
Carefully lift and hang the corner cabinet at the corner of the wall on the cabinet hanger rails. Make sure the wall hanging brackets sits on the rail properly.
A
44
A
A
B
Two or more people are required to lift/move cabinets into place.
Wall Cabinets Installation
5
Add shims to the bottom of the cabinet.
Using a level make sure the cabinet is plumb vertically and horizontally from the front to the back and left to right.
Use an exacto knife to cut the shims after installing all the wall cabinets.
6
Wall cabinets can be adjusted vertically by adjusting the screw noted B in the image below. To fully seat the wall cabinet, ensure screw A is tightened and the cabinet is flush with the wall hanging bracket.
B
A
A
A
B
B
B
A
7
Referencing your design layout, locate the two wall hanging brackets on the next cabinet and ensure they are fully extended.
8
Fully extend all the wall hanging brackets by rotating the screw “A“ counter clockwise. Use the extended philips bit for best results.
A
A
A
45
Wall Cabinets Installation
9
Using two people, carefully lift and hang the cabinet ensuring the wall hanging brackets are securely mounted onto the wall hanging rail. Adjust the cabinet until it is adjacent to the corner cabinet.
10
Wall cabinets can be adjusted vertically by adjusting the screw noted B in the image below. To fully seat the wall cabinet, ensure screw A is tightened and the cabinet is flush with the wall hanging bracket.
Two or more people are required to lift/move cabinets into place.
11
Place the cabinet horizontally close to the corner cabinet. Add shims to the bottom of the cabinet and place a level on the top to make sure the cabinets are level.
Use an exacto knife to cut the shims after installing all the wall cabinets.
B
B
A
A
A
B
B
A
46
Wall Cabinets Installation
12 Fix both cabinets together to prevent movement using a c-clamp. Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach cabinets together.
2”
2”
2”
2”
2”
2”
13 Cover all the wall hanging brackets with covers provided in the hardware box.
47
Wall hanging bracket cover
Wall Cabinets Installation
14
Similarly install other wall cabinets according to the layout and secure cabinets with eachother.
2”
2”
Note: Cabinets must be attached together and attached to the wall. It is recommended to install side panels after attaching all cabinets together. Attach cabinets to the wall after installation of wall side panels.
48
Wall Cabinets Installation
15
Install wall side panels near the open end of the cabinets.
16
Align the side panel to the top. Leave a space of length L on front as shown below to align the side panel with front face of the door.
L
17 Doors may needed to be installed on the cabinet for the correct measurement “ L ”.
18
Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach side panels.
L
2”
49
Wall Cabinets Installation
19
Pre-drill a pilot hole (5/32” drill bit) on the back panel of the cabinets at 3/4” from the bottom, aligned with the wall studs. Attach all cabinets to the wall with 6x70mm Lag screw using a power tool.
Pre-drill
3/4”
Lag screws
3/4”
50
Installing the Above Fridge Cabinet
1
Parts required
1 Place the fridge cabinet between the two extended side panels.
C - Clamps
Ø4mm X 30mm
Chipboard Screws
Side Panels Drill
2
Align the side panel to the top and leave a space of length “ L ” on front as shown below to make sure the side panel flushes with the door front face. Doors may needed to be installed on the cabinet for the correct measurement “ L ”.
L
3 Secure side panels in place using
C-clamps.
L
4 Make sure the side panels are flush with the top of the cabinet.
Cabinet - Top view
51
Installing the Above Fridge Cabinet
5
Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach side panels.
6
Carefully lift the cabinet and move it next to the wall cabinets according to the layout.
2”
7 Adjust all 4 feet by rotating them to make sure the cabinet is level.
8
Two or more people are required to lift/move cabinets into place.
Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach cabinets together.
2” 2”
Max. 3/4” adjustable
9
Pre -drill two pilot holes at 3/4” from bottom and top aligned with the wall studs using a 3/32” drill bit. Screw in the cabinet to the wall stud using the
Ø6x70mm Lag screws provided.
2”
2”
2” 2”
52
2”
2”
Installing the Wall Cabinet Side Panels
(Installed for the cabinets without under cabinet skirting)
1
Parts required
1 Use a standard height side panel when under cabinet skirt is not being installed.
C - Clamps
Ø4mm X 30mm
Chipboard Screws
Side Panels Drill
2 Drill in four Ø4mm x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach side panel.
53
Remove the C-Clamp and follow steps
1 and 2 to install side panels wherever needed.
Installing the Wall Cabinet Side Panels
(Installed for the cabinets with under cabinet skirting)
1
Parts required
1
Use side panel for skirting when under cabinet skirt is being installed below the wall cabinets.
C - Clamps
Ø4mm X 30mm
Chipboard Screws
Side Panels Drill
2 Drill in four Ø4mm x30mm chip board screws at all corners by leaving a gap of 2” from the edges to attach side panel.
43
Remove the C-Clamp and follow steps
1 and 2 to install side panels wherever needed.
54
Installing the Crown Moldings
1
Parts required
Miter Box Saw
Crown Moldings Drill
Ø3.5mm X 35mm
Chipboard Screws
Cut the crown moldings to required length with an angular cut of 45 degrees at the edges.
Measure the length of cabinets on top to cut a required length of Crown Moldings.
L
L
Install Crown Moldings on top of the cabinets.
L
Drill two pilot holes at each corner and drill in the Ø3.5mm X35mm chipboard screws into the pilot holes.
55
Installing the Wall cabinet Skirting
1
Parts required
1 Measure the length of cabinet skirting required under the wall cabinets.
Miter Box Saw
Undermount Skirt Drill
Ø3.5mm X 35mm
Chipboard Screws
L
2 Cut the cabinet skirting to a required length using a hand saw and a miter box.
4 Place the cabinet skirting under the cabinet between the sidepanels.
L
5 Drill pilot holes at the corners and drill in the Ø3.5mm X35mm chipboard screws.
56
Installing the Base Cabinet Side Panels
1
Parts required
Install side panel near the open end of the cabinets..
C - Clamps
Ø4mm X 30mm
Chipboard Screws
Side Panels Drill
Align the side panel to the top and leave a space of length “ L ” on front as shown below to make sure the side panel flushes with the door front face. Doors may needed to be installed on the cabinet for the correct measurement “ L ”.
L
L
L
57
Installing the Base Cabinet Side Panels
Adjust the position of side panel by rotating the feet and make sure the top surface of the panel is flush with the cabinet.
Drill in four Ø4x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach side panel.
2” 2”
2”
2”
2”
58
Installing the Toe kicks
1
Parts required
1
Measure the length of toekicks needed for each set of cabinets and cut the toekick using a hand saw.
Miter Box Saw
L
Toekick Drill
Ø3.5X16 wood screws
2 Cut the Toekicks to required length using a hand saw and a miter box..
3
Place toekick closer to the legs and mark the position of legs on to the toekick for installation of feet clamps.
L
4
Install feet clamps on the toekicks as per the markings.
A B
59
Installing the Toe kicks
5
Push and fit the toekicks to the feet.
6 Make sure the feet clamps are fit properly with the feet.
60
Installing the Filler piece
1
Parts required
Ø4mm X 30mm
Chipboard Screws
1 Identify the leftover space between the cabinets and the wall.
Side Panel Drill Saw
2 Measure the space between the wall and the cabinets.
W
3
Cut the side panel into three pieces. One with the measured width to cover the space and two with a width of 2”.
W 2” 2”
Wall
5
Take one of the 2” strips and attach it to the side panel of the cabinet using a
Ø4mmX 30mm chip board screws.
4
Take the other 2” strip and attach it to the wall aligned with the height of the cabinet using a Ø4mm X 30mm chip board screws.
61
Installing the Filler piece
5 Apply silicone to the front faces of the panel strips.
6 Attach the filler piece aligned with the cabinet.
62
Corner Layout Installation
Install doors, drawers and handles of the cabinets after installing all the accessories. Adjust the position of doors and drawer fronts.
Installing the Linear layout
Note: When installing a linear layout, it is recommended to begin the installation with the tallest cabinets, either a pantry or above fridge cabinet. For a linear layout without pantry or above fridge cabinet, begin with a wall cabinet at end.
1 Install leveling legs of the pantry cabinet.
Refer to the
page 32 for installation of legs.
2
Remove the doors of pantry cabinet.
for the door removal procedure.
3
Install Pantry cabinet at the end as per the planned linear layout. Take into consideration the fact that there is a handle and should adjust opening accoringly.
64
Installing the Linear layout
4 Install the above fridge wall cabinet next to the pantry cabinet. Refer to
for installation of above fridge cabinet along with the side panels.
5
Install cabinet hanger rails on the wall as per the layout. Refer to page 40
for installing the Wall cabinet hanger rails.
65
Installing the Linear layout
6 Install all wall cabinets, and attach the cabinets to each other. Refer the
to install, attach and level the wall cabinets on the wall.
7
Remove the doors of all the base cabinets.
Refer to page 19 - 21 for the door removal
procedure.
8
Install leveling legs for all the base
cabinets. Refer to the page 32 for
installation of legs.
Installing the Linear layout
9
Install all the base cabinets according to the layout and attach all the adjacent cabinets to
each other. Secure all base cabinets to the wall. Refer the pages 37-39
for installing the base cabinets.
10
Install standard height wall cabinet side panels wherever needed. Refer to the
.
11
Install extended height wall cabinet side panels wherever needed. Refer to the
67
Installing the Linear layout
12
Install crown moldings for all the wall cabinets. Refer to the
.
13
Install cabinet skirtings for all the wall
cabinets. Refer to the page 56 .
14
Install side panels wherever needed for the base cabinets. Refer to the
.
15
Install toekicks for all the base cabinets.
Refer to the
.
68
Installing the Island layout
The Island layout can be created by combining base cabinets together (Island) to existing corner
or linear layouts. For the installation of linear layout refer the pages 64 - 68
.
For the installation of corner layout refer the
.
Linear
Island
Creating a 26” Deep Island
The 26” wide island is constructed by attaching the base cabinets next to eachother.
1
Parts and Tools required
Chip board screw for
Cabinets
Ø4mm X 30mm
Drill Phillips Bit C - Clamps Toekick Island Side Panels Island Back Panels
69
Installing the Island layout
1
Install three base cabinets next to each other and join them using c-clamps.
2”
2
Fix the cabinets together to prevent movement using a c-clamp. Drill in four Ø4mm x30mm chip board screws at all corners by leaving a gap of 2inches from the edges to attach cabinets together.
2”
2”
2”
2”
2”
70
Installing the Island layout
3
Attach back panels to the rear side of all cabinets and adjust the levelling legs to flush the panels with the top of the cabinet. Make sure to align panels with the sides of the cabinet.
4
Drill in four Ø4mm x30mm chip board screws at all corners from inside to fix the back panels.
Max. 3/4” adjustable
5 Attach Island side panels and drill in four chipboard screws from inside at all four corners.
Refer to the
page 57 for detailed instuctions on installing the side panels.
71
Installing the Island layout
6 Install toekicks for all the base cabinets. Refer to the
for detailed instuctions on installing the toekicks.
7 Install Custom countertop to finish the Island. NewAge does not offer Countertops for Islands.
Measure the length and with of the cabinet to order custom countertop.
72
Installing the Island layout
Creating a 40” Deep Island
The 40” wide island is constructed using base cabinets and wall cabinets that are lined up back to back.
1
Parts and Tools required
1 A set of wall cabinets and base cabinets are needed to create a 40” deep island.
Base Cabinets
Adjustable leg for Wall Cabinets
Chip board screw for
Cabinets
Ø4mm X 30mm
Drill
Wall Cabinets
C - Clamps Toekick Phillips Bit
Extended
Island Side Panels
Island Back Panels
1 Install three base cabinets next to each other and join them using c-clamps.
2
Drill in four Ø4mmx30mm chip board screws at all corners by leaving a gap of
2inches from the edges to attach cabinets together.
73
Installing the Island layout
3
Flip the wall cabinet, pre drill four pilot holes at all four corners of the cabinet base. Fix all four legs to the cabinet using the screws provided.
4
Install wall cabinets back to the Base cabinets and fix the cabinets together by drilling in four Ø4x30mm chip board screws at all corners by leaving a gap of
2inches from the edges to attach cabinets together.
5
Attach Extended Island side panels and adjust the levelling legs to flush the panels with the top of the cabinet. Drill in four chipboard screws from inside at all four corners.
6
Install toekicks for all the base cabinets.
Refer to the
for detailed instuctions on installing the toekicks.
74
Max. 3/4” adjustable
Installing the Island layout
7 Install custom countertop to finish the Island. NewAge does not offer Countertops for the cabinet Islands. Measure the length and width of the cabinet to order custom countertop.
75
Installing the U shaped layout
1 Remove doors for all the wall cabinets.
.
2 Install rails on the wall and install the
corner wall cabinet. Refer to page 40 .
3 Install all the adjacent wall cabinets, make sure the cabinets are level, attach the cabinets together and secure cabinets to the wall. Refer to
.
76
Installing the U shaped layout
4
Remove the doors of all the base cabinets.
Refer to page 19 - 21 for the door removal
procedure.
5
Install leveling legs for all the base cabinets. Refer to the
for installation of legs.
6
Install corner base cabinets as shown in the layout with a spacing of 9inches from the wall.
9”
77
Installing the U shaped layout
7 Install all base cabinets, make sure the cabinets are level, attach cabinets together and secure cabinets to the wall. Refer the
for installing the base cabinets.
8
Install Above fridge cabinet. Refer to page
9
Install standard height wall cabinet side panels wherever needed. Refer to the
78
Installing the U shaped layout
10
Install extended height wall cabinet side panels wherever needed. Refer to the
.
11
Install crown moldings for all the wall cabinets. Refer to the
.
12
Install cabinet skirtings for all the wall cabinets. Refer to the
.
13
Install side panels wherever needed for
the base cabinets. Refer to the page 57 .
79
Installing the U shaped layout
14
Install toekicks for all the base cabinets.
Additional Acc essories off ered by NewAge
LED’s
To Install LED’s refer to the LED Install
Instructions.
Shelves
To Install Shelves refer to the Shelf
Installation guide.
80
Additional Acc essories off ered by NewAge
Handles
To Install Door Handles refer to the
Handles Install guide.
Sink
To Install Sink refer to the Home kitchen
Sink Install Instructions.
81
Granite Countertops
To Install Countertops refer to the Granite
Countertops Install guide.
Spare Parts
SPARE PARTS - BASE CABINET with DOORS
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
83
Toe kick clips x4
Adjustable leg x4
Spare Part
Kit 1
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Hinge 110º x 2
Screws x 4
Spare Part Kit 10
Cabinet Shelf 12”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 22
Cabinet Shelf 18”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 23
Cabinet Shelf 24”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 24
Cabinet Shelf 36”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 25
SPARE PARTS -
BASE CABINET with DOORS
Part #
HKC-169A-01
HKC-170A-01
HKC-174A-01
HKC-178A-01
HKC-194A-01
HKC-195A-01
HKC-196A-01
HKC-197A-01
Description
Levelling Legs
Spare Part Kit 1
Toe Clips
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L - LIH
LIN
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part Kit-10
Hinge 110° With Plate & Two Screws
Spare Part Kit-22
Shelf - 12inch
Shelf Support Bracket
Spare Part Kit-23
Shelf - 18 inch
Shelf Support Bracket
Shelf - 24 inch
Spare Part Kit-24
Shelf Support Bracket
Spare Part Kit-25
Shelf - 24 inch
Shelf Support Bracket
18 Inch
SKU
85100
85101
85105
85109
85119
85120
85121
85122
24 Inch
SKU
85100
85101
85105
85109
85119
85120
85121
85122
36 Inch
SKU
85100
85101
85105
85109
85119
85120
85121
85122
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
84
Cabinets
12” & 24” Base
36” Base
Description Item #
12” Door
18” Door
1
3
SPARE PARTS - BLIND CORNER
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
Toe kick clips x4
Adjustable leg x4
Spare Part
Kit 1
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Hinge 95º x 2
Screws x 4
Spare Part
Kit 14
85
Blind Corner Shelf
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 9
Part #
HKC-169A-01
HKC-170A-01
HKC-174A-01
HKC-177A-01
HKC-182A-01
SPARE PARTS -
BLIND CORNER
Description
Levelling Legs
Spare Part Kit 1
Toe Clips
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part Kit-9
Shelf - Blind Corner
Shelf Support Bracket
Spare Part Kit-14
Hinge 95° Blind Corner With Two Screws
18 Inch
SKU
85100
85101
85105
85108
85111
24 Inch
SKU
85100
85101
85105
85108
85111
36 Inch
SKU
85100
85101
85105
85108
85111
For Door and Blind Corner Filler Replacement
Refer to Door and Drawer Reference Table for SKUs
Cabinets Description Item #
Blind Corner Filler Filler 27
Blind Corner Door 18” Door 3
86
SPARE PARTS - 3 DRAWER
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
Toe kick clips x4
Adjustable leg x4
Spare Part
Kit 1
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Drawer Stabilizer x 1
Spare Part
Kit 11
Chipboard
Screw x 1
4 x 15.5L
87
Drawer Front
Connector x 4
Support bar locks x8
Spare Part
Kit 12
Drawer Deep Spacer 550L x 4
Drawer Deep Spacer 550R x 4
Spare Part
Kit 13
Drawer
Shallow
Spare Part
Kit 3
Drawer Deep
Spare Part
Kit 4
88
SPARE PARTS -
3 DRAWER
Part #
HKC-169A-01
HKC-170A-01
HKC-171A-01
HKC-172A-01
HKC-174A-01
HKC-179A-01
HKC-180A-01
HKC-181A-01
Description
Levelling Legs
Spare Part Kit 1
Toe Clips
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L - LIH
LIN
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-3
Drawer Shallow M550LSet
Spare Part Kit-4
Drawer Deep D550LSet
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part Kit-11
Drawer Stabilizer(Only for 36” Drawers)
Chipboard Screw-PZ2-Thread Dia 4X15.5L
Spare Part Kit-12
Drawer Deep Spacer Support Lock
Drawer Front Connector
Spare Part Kit-13
Drawer Deep Spacer 550L
Drawer Deep Spacer 550R
18 Inch
SKU
85100
85101
85102
85103
85105
85110
XXXXX
XXXXX
24 Inch
SKU
85100
85101
85102
85103
85105
85110
XXXXX
XXXXX
36 Inch
SKU
85100
85101
85102
85103
85105
85110
XXXXX
XXXXX
89
SPARE PARTS -
3 DRAWER
Cabinets
18” 3 Drawer
18” 3 Drawer
24” 3 Drawer
24” 3 Drawer
36” 3 Drawer
36” 3 Drawer
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
Description
18in Top Drawer (Panel)
18in Mid/Bottom Drawer (Panel)
24in Top Drawer (Panel)
24in Mid/Bottom Drawer (Panel)
36in Top Drawer (Panel)
36in Mid/Bottom Drawer (Panel)
6
9
7
10
Item #
5
8
SPARE PARTS - SPLIT DRAWER and DOORS
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
Toe kick clips x4
Adjustable leg x4
Spare Part
Kit 1
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Hinge 110º x 2
Screws x 4
Spare Part Kit 10
Drawer Stabilizer x 1
Spare Part
Kit 11
Chipboard
Screw x 1
4 x 15.5L
Drawer Front
Connector x 4
Support bar locks x8
Spare Part
Kit 12
90
Cabinet Shelf 24”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 24
Cabinet Shelf 36”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 25
Drawer
Shallow
Spare Part
Kit 3
Cabinet Shelf 18”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 23
91
SPARE PARTS - SPLIT
DRAWER and DOORS
18 Inch
SKU
85100
24 Inch
SKU
85100
36 Inch
SKU
85100
Part #
HKC-169A-01
HKC-170A-01
HKC-171A-01
HKC-174A-01
HKC-178A-01
HKC-180A-01
HKC-149A-01
HKC-195A-01
Description
Levelling Legs
Spare Part Kit 1
Toe Clips
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L - LIH
LIN
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-3
Drawer Shallow M550LSet
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part Kit-10
Hinge 110° With Plate & Two Screws
Hardware Kit-12
Drawer Stabilizer(Only for 36” Drawers)
Chipboard Screw-PZ2-Thread Dia 4X15.5L
Spare Part Kit-13
Drawer Deep Spacer Support Lock
Drawer Front Connector
Spare Part Kit-23
Shelf - 18 inch
Shelf Support Bracket
85101
85102
85105
85109
XXXXX
XXXXX
85120
85101
85102
85105
85109
XXXXX
XXXXX
85120
85101
85102
85105
85109
XXXXX
XXXXX
85120
92
SPARE PARTS - SPLIT
DRAWER and DOORS
18 Inch
SKU
85121
24 Inch
SKU
85121
36 Inch
SKU
85121
Part #
HKC-196A-01
HKC-197A-01
Description
Shelf - 24 inch
Spare Part Kit-24
Shelf Support Bracket
Spare Part Kit-25
Shelf - 36 inch
Shelf Support Bracket
85122 85122 85122
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
Cabinets
12in Split Base (Door)
18in Split Base (Door)
18in Top Drawer (Panel)
24in Top Drawer (Panel)
36in Top Drawer (Panel)
Description
Door
Door
Top Drawer
Top Drawer
Top Drawer
5
6
7
Item #
2
4
SPARE PARTS - PANTRY
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
93
Toe kick clips x4
Adjustable leg x4
Spare Part
Kit 1
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Screws x 4
Hinge 155° x 2
Spare Part
Kit 16
Cabinet Shelf 18”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 23
Cabinet Shelf 24”
X 1
Shelf Support Bracket
X 4
Spare Part
Kit 24
Pantry Fixed Shelf
18” X 1
Tab Shelf
Boss Insert
X 4
Pantry Fixed Shelf
24” X 1
Tab Shelf
Boss Insert
X 4
Tab Shelf
Support
X 4
Spare Part
Kit 26
Euro Screw
6x13.5L
X 4
Tab Shelf
Support
X 4
Spare Part
Kit 27
Euro Screw
6x13.5L
X 4
94
SPARE PARTS - PANTRY
18 Inch
SKU
85100
24 Inch
SKU
85100
Part #
HKC-169A-01
HKC-170A-01
HKC-174A-01
HKC-184A-01
HKC-184A-01
HKC-196A-01
HKC-198A-01
Description
Levelling Legs
Spare Part Kit 1
Toe Clips
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L - LIH
LIN
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part Kit-16
Hinge 155° With Plate & Two Screws
Shelf - 18 inch
Spare Part Kit-23
Shelf Support Bracket
Spare Part Kit-24
Shelf - 24 inch
Shelf Support Bracket
Spare Part Kit-26
Pantry Fixed Shelf - 18 inch
Tab Shelf Boss Insert
Tab Shelf Support Element
Euro Screw-PZ2 Thread Dia 6X13.5L
85101
85105
85113
85120
85121
85123
85101
85105
85113
85120
85121
85123
36 Inch
SKU
85100
85101
85105
85113
85120
85121
85123
95
Part #
HKC-199A-01
SPARE PARTS - PANTRY
Description
Spare Part Kit-27
Pantry Fixed Shelf - 24inch
Tab Shelf Boss Insert
Tab Shelf Support Element
Euro Screw-PZ2 Thread Dia 6X13.5L
18 Inch
SKU
85124
24 Inch
SKU
85124
36 Inch
SKU
85124
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
Cabinets
18in Pantry (Door)
18in Pantry Extended (Door)
24in Pantry (Door)
24in Pantry Extended (Door)
Description
Standard Door
Extended Door
Standard Door
Extended Door
Item #
13
14
15
16
SPARE PARTS - SINK CABINET
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
Toe kick clips x4
Adjustable leg x4
Spare Part
Kit 1
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Hinge 110º x 2
Screws x 4
Spare Part Kit 10
96
Frame
Component
X 1
Panel
Component
X 1
Euro Screw
X 4
6 x13.5L
Spare Part
Kit 15
97
SPARE PARTS -
SINK CABINET
Part #
HKC-169A-01
HKC-170A-01
HKC-174A-01
HKC-178A-01
HKC-183A-01
Description
Levelling Legs
Spare Part Kit 1
Toe Clips
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part-10
Hinge 110° With Plate & Two Screws
Spare Part Kit-15
Panel Component Keku
Euro Screw-PZ2 Thread Dia 6X13.5L
18 Inch
SKU
85100
85101
85105
85109
85112
24 Inch
SKU
85100
85101
85105
85109
85112
36 Inch
SKU
85100
85101
85105
85109
85112
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
Cabinets
12in Split Base (Door)
18in Split Base (Door)
24in Sink False Drawer (Panel)
36in Sink False Drawer (Panel)
Description
Door
Door
Top Drawer
Top Drawer
Item #
2
4
11
12
SPARE PARTS - STANDARD WALL CABINETS
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
98
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Spare Part
Kit 5
Wall Cabinet Shelf 12”
X 1
Shelf Support Bracket
X 4
Spare Part Kit 18
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Hinge 110º x 2
Screws x 4
Spare Part Kit 10
Wall Cabinet Shelf 18”
X 1
Shelf Support Bracket
X 4
Spare Part Kit 19
Wall Cabinet Shelf 24”
X 1
Shelf Support Bracket
X 4
Spare Part Kit 20
Wall Cabinet Shelf 36”
X 1
Shelf Support Bracket
X 4
Spare Part Kit 21
SPARE PARTS - STANDARD
WALL CABINETS
Part #
HKC-170A-01
HKC-173A-01
HKC-174A-01
HKC-178A-01
HKC-186A-01
HKC-187A-01
HKC-188A-01
HKC-193A-01
Description
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-5
Wall mounting bracket cover
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part-10
Hinge 110° With Plate & Two Screws
Spare Part Kit-18
12” Wall Cabinet Shelf
Spare Part Kit-19
18” Wall Cabinet Shelf
Spare Part Kit-20
24” Wall Cabinet Shelf
Spare Part Kit-21
36” Wall Cabinet Shelf
18 Inch
SKU
85101
85104
85105
85109
85115
85116
85117
85118
24 Inch
SKU
85101
85104
85105
85109
85115
85116
85117
85118
36 Inch
SKU
85101
85104
85105
85109
85115
85116
85117
85118
99
SPARE PARTS - STANDARD
WALL CABINETS
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
Cabinets
12” & 24” Wall
36” Wall
Above Fridge Cabinet (Door)
Above Fridge Cabinet Extended (Door)
Above Stove Cabinet (Door)
Above Stove Cabinet Extended (Door)
Description
12” Door
18” Door
Standard Door
Extended Door
Standard Door
Extended Door
18
19
20
Item #
1
3
17
100
SPARE PARTS - CORNER WALL CABINET
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Spare Part
Kit 5
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Hinge 110º x 2
Screws x 4
Spare Part Kit 10
Corner Wall
Cabinet Shelf
X 1
Shelf Support
Bracket
X 5
Spare Part
Kit 30
101
102
SPARE PARTS - CORNER WALL CABINET
Part #
HKC-170A-01
HKC-173A-01
HKC-174A-01
HKC-178A-01
HKC-202A-01
Description
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L - LIH
LIN
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-5
Wall Mounting Bracket Cover RH
Wall Mounting Bracket Cover LH
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part Kit-10
Hinge 110° With Plate & Two Screws
Spare Part Kit-30
Corner Cabinet Shelf
Shelf Support Bracket
18 Inch
SKU
85101
85104
85105
85109
85127
24 Inch
SKU
85101
85104
85105
85109
85127
36 Inch
SKU
85101
85104
85105
85109
85127
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
Cabinets
Corner Wall Cabinet - A with handle (Door)
Corner Wall Cabinet - B without handle (Door)
Corner Wall Extended Cabinet - A with handle (Door)
Corner Wall Extended Cabinet - B without handle (Door)
Description Item #
Door
Door
Door
Door
23
24
25
26
SPARE PARTS - GLASS DOOR WALL CABINETS
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Chip board screw for Toe kick Clips
Ø4mm X 40mm x4
Chip board screw for Toe kick Clips
Ø3.5mm X 35mm x4
Molly Bolt x 2
Cover Cap x 4
Chip board screw for
Cabinets
Ø4mm X 30mm x8
Lag Screw
Ø6mm X 70mm x3
Spare Part
Kit 2
Lag Screw
Cover Cap and
Washer x4
Side Panel
Adjustable Leg x2
103
Chip board screw for Toe kick Clips
Ø3.5mm X 16mm x4
Spare Part
Kit 5
Glass Cabinet Shelf 36”
X 1
Shelf Support Bracket
X 5
Spare Part
Kit 28
Door Bumper x2
Tab Shelf
Support
X 4
Euro Screw-
Dia 6X13.5L
x8
Tab Shelf
Boss Insert
X 4
Shelf Support
Bracket x 4
Glass Shelf
Support Bracket
X 4
Spare Part
Kit 6
Shelf Support
Pin X 4
Hinge 110º x 2
Screws x 4
Spare Part Kit 10
Glass Cabinet Shelf 36”
X 1
Shelf Support Bracket
X 5
Spare Part
Kit 29
SPARE PARTS - GLASS DOOR WALL CABINETS
Part #
HKC-170A-01
HKC-173A-01
HKC-174A-01
HKC-178A-01
HKC-200A-01
HKC-201A-01
Description
Spare Part Kit 2
Chipboard Screw-PZ2 Thread Dia 4X30L
Lag Screw-Thread Dia 6X70L
Chipboard Screw-PZ2-Thread Dia 3.5X16L
Chipboard Screw-PZ2-Thread Dia 4X40L - LIH
LIN
Cover Cap - Dia 17 PZ2 Cross Slot
Molly Bolt- HM 6x37 S
Adj Leg- M6x25L With Insert
Cover Cap for Mounting Screw
Chipboard Screw-PZ2-Thread Dia 3.5X35L
Spare Part Kit-5
Wall Mounting Bracket Cover RH
Wall Mounting Bracket Cover LH
Spare Part Kit-6
Shelf Support Pin Dia 4.9x16L
Glass Shelf Support Clip
Euro Screw
Door Bumper
Shelf Support Bracket
Tab Shelf Boss Insert
Tab Shelf Support Element
Spare Part Kit-10
Hinge 110° With Plate & Two Screw
Spare Part Kit-28
Glass Shelf - 24 inch
Glass Shelf Support Clip
Spare Part Kit-29
Glass Shelf - 36 inch
Glass Shelf Support Clip
18 Inch
SKU
85101
85104
85105
85109
85125
85126
24 Inch
SKU
85101
85104
85105
85109
85125
85126
36 Inch
SKU
85101
85104
85105
85109
85125
85126
For Door Replacement
Refer to Door and Drawer Reference Table for SKUs
Cabinets
24” Standard Glass Door Cabinet
36” Standard Glass Door Cabinet
24” Extended Glass Door Cabinet
36” Extended Glass Door Cabinet
Description
12in Glass Door
18in Glass Door
12in Glass Door Extended 30
18in Glass Door Extended 31
Item #
28
29
104
DOOR AND DRAWER REFERENCE TABLE
Item
#
Description
1 12in Base/Wall (Door)
2 12in Split Base (Door)
3 18in Base/Wall (Door)
4 18in Split Base (Door)
5 18in Top Drawer (Panel)
6 24in Top Drawer (Panel)
7 36in Top Drawer (Panel)
White
84200 84400 2000AAA 2000AAB 2000AAC 2000AAD
84202 84402 2002AAA 2002AAB 2002AAC 2002AAD
84204 84404 2004AAA 2004AAB 2004AAC 2004AAD
84206
84208
84209
84210
Gray
84406
84408
84409
84410
Polo Cream
2006AAA 2006AAB
2008AAA 2008AAB
2009AAA 2009AAB
2010AAA 2010AAB
Antique
Blue
2006AAC
2008AAC
2009AAC
2010AAC
Black
2006AAD
2008AAD
2009AAD
2010AAD
8 18in Mid/Bottom Drawer (Panel) 84211 84411 2011AAA 2011AAB 2011AAC 2011AAD
9 24in Mid/Bottom Drawer (Panel) 84212 84412 2012AAA 2012AAB 2012AAC 2012AAD
10 36in Mid/Bottom Drawer (Panel) 84213 84413 2013AAA 2013AAB 2013AAC 2013AAD
11 24in Sink False Drawer (Panel) 84214 84414 2014AAA 2014AAB 2014AAC 2014AAD
12 36in Sink False Drawer (Panel)
13 18in Pantry (Door)
84215
84216
84415
84416
2015AAA 2015AAB
2016AAA 2016AAB
2015AAC
2016AAC
2015AAD
2016AAD
14 18in Pantry Extended (Door)
15 24in Pantry (Door)
84217 84417 2017AAA 2017AAB 2017AAC 2017AAD
84218 84418 2018AAA 2018AAB 2018AAC 2018AAD
84219 84419 2019AAA 2019AAB 2019AAC 2019AAD
84220 84420 2020AAA 2020AAB 2020AAC 2020AAD
84222 84422 2022AAA 2022AAB 2022AAC 2022AAD
16 24in Pantry Extended (Door)
17 Above Fridge Cabinet (Door)
18 Above Fridge Cabinet Extended
(Door)
19 Above Stove Cabinet (Door)
20 Above Stove Cabinet Extended
(Door)
21 12in Wall Cabinet Extended
(Door)
22 18in Wall Cabinet Extended
(Door)
23 Corner Wall Cabinet - A with handle (Door)
24 Corner Wall Cabinet - B without handle (Door)
25 Corner Wall Extended Cabinet - A with handle (Door)
26 Corner Wall Extended Cabinet - B without handle (Door)
27 Blind Corner Filler Panel
28 12in Glass Door
29 18in Glass Door
30 12in Glass Door Extended
31 18in Glass Door Extended
84224
84226
84228
84230
84232
84233
84234
84235
84236
84237
84238
84239
84424
84426
84428
84430
84432
84433
84434
84435
84436
84437
84438
84439
84240 84440
2024AAA 2024AAB
2026AAA 2026AAB
2028AAA 2028AAB
2030AAA 2030AAB
2032AAA 2032AAB
2033AAA 2033AAB
2034AAA 2034AAB
2035AAA 2035AAB
2036AAA 2036AAB
2024AAC
2026AAC
2028AAC
2030AAC
2032AAC
2033AAC
2034AAC
2035AAC
2024AAD
2026AAD
2028AAD
2030AAD
2032AAD
2033AAD
2034AAD
2035AAD
2036AAC 2036AAD
NEWAGE PRODUCTS INC. HOME CABINETS
MANUFACTURER WARRANTY
PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call our customer service team:
• Name, address and telephone number
• Product Name / SKU Number
• A clear, detailed description of the problem
• Proof of purchase including order number
Register your NewAge Products purchase online for quicker customer assistance and access to exclusive benefits
Visit www.newageproducts.com/register/
Warranty Claim
For warranty service please contact NewAge Products at
1-877-306-8930; or [email protected]
Please review all warranty details below, prior to contacting NewAge Products for a claim.
Scan the QR code on the right to access our support page or visit www.newageproducts.com/contact-us/
Scan this QR code with the camera on your mobile device to visit the
NewAge Products Support Hub www.newageproducts.com/support-hub/
LIMITED LIFETIME WARRANTY
WHAT IS COVERED
When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products
Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the warranty duration from the purchase date of the product.
WHAT IS NOT COVERED
1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.
2. Damage resulting from products caused by accident, misuse, abuse, fire, flood, improper installation, acts of God, neglect, modification or alteration, normal wear and tear, extreme heat, exposure to the elements including humidity or mishandling.
3. Repairs or replacement when your product is used in other than normal, residential use, such as a commercial environment, improper storage or handled in anyway inconsistent with the installation instructions included with the product.
4. Surfaces damaged due to improper use of chemicals, and detergents.
5. Replacement parts for NewAge products outside Canada and the United States.
6. Loss due to theft.
7. Damage resulting from use of the product contrary and not in accordance to the instruction manual.
8. Any labor costs during the warranty period.
Cabinets are made of natural wood and may vary in texture, color or wood grain, and exhibit subtle changes over time. These variations are considered natural and are not covered under the NewAge warranty program.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR
THE SHORTEST PERIOD ALLOWED BY LAW. THIS WARRANTY IS LIMITED TO THE ORIGINAL BUYER. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AT OUR DISCRETION AS
PROVIDED HEREIN. NEWAGE SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
Advertisement
Related
