Manual

Manual
RF Wireless Remote Control Radio Controller / Transmitter & Receiver
Package Include:
1 x Receiver: S2PFS-DC12 / S2PFS-DC24 (2 Channel / Inversion Control Mode / Speed Adjustable)
1 x Transmitter: CV-6-2
1 x User manual
Features:
Wireless control, easy to install
Control 2 motors forward & reverse simultaneously with the transmitter (remote control) from any place within a reliable distance. Wireless signal can
pass through walls, floors and doors.
Two speed control knobs to adjust the speed of motor separately.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/several transmitters can control one/several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz
Receiver:
Model No.: S2PFS-DC12 / S2PFS-DC24
Control Mode: Inversion Control Mode
Coding Type: Fixed code or learning code
Coding Setting: By learning
Power Supply (Operating Voltage): DC12V±1V (S2PFS-DC12), DC24V±1V (S2PFS-DC24)
Output of Relay: DC12V (S2PFS-DC12), DC24V (S2PFS-DC24)
Maximum Working Current: 10A / each channel
PCB size: 185mm x 105mm x 30mm
Case size: 200mm x 120mm x 55mm
Transmitter:
Model No.: CV-6-2
Channel: 6 CH
Remote Control Distance: 500m / 1500ft (theoretically)
Encode: Fixed code by soldering
Unit Size: 110mm x 50mm x 18mm
Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)
Usage:
Connect terminals “+” and “-” to power supply DC12V / 24V; connect terminals “A1” and “A2” to motor 1; connect terminals “B1” and “B2” to motor 2.
Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)
Press button ▲ on the left: motor 1 rotates in positive direction
Press button ▼ on the left: motor 1 rotates in reversal direction
Press button ■ on the left: motor 1 stops
Press button ▲ on the right: motor 2 rotates in positive direction
Press button ▼ on the right: motor 2 rotates in reversal direction
Press button ■ on the right: motor 2 stops
Setting control mode Momentary: Only connect Jumper-1 (CN1)
Press and hold button ▲ on the left: motor 1 rotates in positive direction
Release button ▲ on the left: motor 1 stops
Press and hold button▼ on the left: motor 1 rotates in reversal direction
Release button ▼ on the left: motor 1 stops
Press and hold button ▲ on the right: motor 2 rotates in positive direction
Release button▲ on the right: motor 2 stops
Press and hold button▼ on the right: motor 2 rotates in reversal direction
Release button ▼ on the right: motor 2 stops
Speed of motor can be adjusted by the knobs:
Twist the knobs anti-clockwise, the speed will be faster.
Twist the knobs clockwise, the speed will be slower.
Knob 1 controls motor 1; Knob 2 controls motor 2.
The corresponding remote control has been matched to the receiver. If you don’t want the receiver to work with the remote control, you can delete all
codes stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
Learning the button of remote control:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Knob 2
Knob 1
RF module
Jumper-2
Jumper-1
+
ADJ2
ADJ1
IC
Signal LED
Relay 1
Relay 2
_
Power Supply DC12V
Button
Power LED
Antenna
B1
B2
Relay 4
Relay 3
A2
A1
Application Circuit
M
M
Motor 2
Motor 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement