CB Series PC/104-Plus User`s Manual v3

CB Series PC/104-Plus User`s Manual v3
CB Series PC/104-Plus Multiport Serial Module
User’s Manual
www.moxa.com/product
Third Edition, December 2007
Moxa Technologies Co., Ltd.
Tel: +886-2-8910-1230
Fax: +886-2-8910-1231
Web: www.moxa.com
Moxa Technical Support
[email protected]
Worldwide:
The Americas [email protected]
CB Series PC/104-Plus Multiport Serial Module
User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in
accordance with the terms of that agreement.
Copyright Notice
Copyright © 2007 Moxa Technologies Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
Moxa is a registered trademark of the Moxa Group.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the
part of MOXA.
MOXA provides this document “as is,” without warranty of any kind, either expressed or implied, including, but
not limited to, its particular purpose. MOXA reserves the right to make improvements and/or changes to this
manual, or to the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, MOXA assumes no
responsibility for its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the
publication.
Table of Contents
Chapter 1
Introduction ...............................................................................................1-1
Overview .............................................................................................................................. 1-2
Package Checklist................................................................................................................. 1-2
Product Features ................................................................................................................... 1-2
Product Specifications .......................................................................................................... 1-3
Chapter 2
Hardware Installation ................................................................................2-1
Hardware Installation ........................................................................................................... 2-2
Block Diagrams .................................................................................................................... 2-2
Rotary Switch ............................................................................................................... 2-3
Serial Interface Selection...................................................................................................... 2-3
Chapter 3
Software Installation .................................................................................3-1
Windows Vista (32-bit and 64-bit) ....................................................................................... 3-2
Installing the Driver...................................................................................................... 3-2
Using Device Manager to Verify Installation............................................................... 3-8
Port Configuration ...................................................................................................... 3-10
Windows XP, 2003 (32-bit and 64-bit) ................................................................................3-11
Installing the Driver.................................................................................................... 3-11
Using Device Manager to Verify Installation............................................................. 3-17
Port Configuration ...................................................................................................... 3-18
Using PComm............................................................................................................. 3-20
Using Event Log......................................................................................................... 3-20
Disabling the Module ................................................................................................. 3-20
Uninstalling the Module ............................................................................................. 3-21
Windows 2000.................................................................................................................... 3-22
Installing the Driver.................................................................................................... 3-22
Using Device Manager to Verify Installation............................................................. 3-28
Port Configuration ...................................................................................................... 3-29
Using PComm............................................................................................................. 3-30
Using Event Log......................................................................................................... 3-31
Disabling the Module ................................................................................................. 3-31
Uninstalling the Module ............................................................................................. 3-32
Linux (32-bit and 64-bit) .................................................................................................... 3-34
DOS .................................................................................................................................... 3-34
Installing the Driver.................................................................................................... 3-34
Driver Setup................................................................................................................ 3-35
Loading the Driver...................................................................................................... 3-37
Unloading the Driver .................................................................................................. 3-37
Windows CE 5.0................................................................................................................. 3-37
Installing the driver..................................................................................................... 3-37
Chapter 4
Serial Programming Tools........................................................................4-1
Serial Programming Library................................................................................................. 4-2
PComm Utilities ................................................................................................................... 4-2
Installation .................................................................................................................... 4-2
PComm Diagnostic....................................................................................................... 4-2
PComm Monitor ........................................................................................................... 4-3
PComm Terminal Emulator.......................................................................................... 4-3
Chapter 5
Pin Assignments .......................................................................................5-1
Box Header Pin Assignments ............................................................................................... 5-1
RS-232.......................................................................................................................... 5-1
RS-422, 4-wire RS-485 ................................................................................................ 5-1
2-wire RS-485............................................................................................................... 5-2
Serial Cable Pin Assignments............................................................................................... 5-2
DB9(M) Connectors ..................................................................................................... 5-2
DB25(M) Connectors ................................................................................................... 5-3
1
Introduction
Chapter 1
Welcome to the CB Series of PC/104-Plus communication modules, a multiport serial module for
industrial applications. It is designed for PC/104-Plus CPU boards that accept the PC/104-Plus
expansion interface. Optional DB9 and DB25 cables are available to connect different devices.
The device drivers make full use of the 128-byte Tx/Rx FIFO and on-chip flow control, which
allows up to 921.6 Kbps data transmission.
The CB Series includes the following models:
8 ports, RS-232
CB-108:
CB-108-T: 8 ports, RS-232, wide temperature
4 ports, RS-232/422/485
CB-114:
CB-114-T: 4 ports, RS-232/422/485, wide temperature
4 ports, RS-422/485, optical isolation protection
CB-134I:
CB-134I-T: 4 ports, RS-422/485, optical isolation protection, wide temperature
2 KV optical isolation is provided on optical isolation models. Wide temperature models are rated
for operation between -40 to 85°C.
The following topics are covered in this chapter:
‰
‰
‰
‰
Overview
Package Checklist
Product Features
Product Specifications
CB Series User’s Manual
Introduction
Overview
The CB Series PC/104-Plus module is designed to be used with PC/104-Plus CPU modules or
CPU cards with the PC/104-Plus expansion interface. Models are available for RS-232, RS-422,
and RS-485, with 4 or 8 ports. The serial ports are accessed through a 40-pin box header connector
on the module. DIP switches allow you to select the serial interface. The industry-standard MOXA
UART (16C550 compatible) is fully programmable. Built-in 15 KV ESD protection protects
devices connected to the serial network.
Package Checklist
MOXA performs a careful mechanical and electrical inspection of each module prior to shipping.
Your module should arrive in perfect electrical order, free of any marks or scratches. Please handle
the module by the edges only, since your body’s static charge can damage the integrated circuits.
When the module is not in use, please keep it in the anti-static package provided. You may also
use this package to return the module if it requires repair.
The CB Series module is shipped with the following items:
y
y
y
y
CB Series PC/104-Plus multiport serial module
Documentation and Software CD
Quick Installation Guide
5-year product warranty statement
Note: Please notify your sales representative if any of the above items are missing or damaged.
Product Features
The CB Series module features the following:
y
y
y
y
y
y
y
4 or 8 serial ports (depending on model)
RS-232, RS-422, or RS-485 operation (depending on model)
128-byte FIFOs and on-chip flow control
Up to 921.6Kbps data transmission speed
Built-in 15 KV ESD protection
Onboard Tx, Rx LED indicators for each port
Optional wide temperature support (-40 to 85°C)
1-2
CB Series User’s Manual
Introduction
Product Specifications
CB Series PC/104-Plus Multiport Serial Module
Hardware
I/O controller
Connector Type
Interface
Bus
No. of Ports
Max. No. of Modules
Signals
RS-232
RS-422
4-wire RS-485
2-wire RS-485
Performance
Baudrate
Configuration
Parity
Data Bits
Stop Bit(s)
IRQ
FIFO
Additional Settings
Driver Support
Power and Environment
Operating Temperature
Operating Humidity
Storage Temperature
ESD Protection
Other
Dimensions (W x D)
Regulatory Approvals
Warranty
MU860 (16C550C compatible)
40-pin box header
PC/104-Plus (PCI) bus
4 ports (CB-114, CB-134I)
8 ports (CB-108)
4
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND
TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND
Data+(B), Data-(A), GND
50 bps to 921.6 Kbps
None, Even, Odd, Space, Mark
5, 6, 7, 8
1, 1.5, 2
BIOS assigned
128 bytes
Serial interface selection by DIP switch
DOS
Windows 2000, Windows XP/2003/Vista (x86 and x64)
Linux 2.4, Linux 2.6 (x86 and x64)
Standard models: 0 to 55°C (32 to 131°F)
“-T” models:, -40 to 85°C (-40 to 185°F)
5 to 95% RH
-40 to 70°C (-40 to 158°F)
Embedded 15 KV ESD protection
96 x 90 mm
EN55022 Class A, EN55024, EN6100-3-2, EN61000-3-3, FCC
Part 15 Class A
5 years
1-3
2
Hardware Installation
Chapter 2
This chapter explains how to install the CB Series PC/104-Plus multiport serial module.
The following topics are covered:
‰ Hardware Installation
‰ Block Diagrams
¾ Rotary Switch
‰ Serial Interface Selection
CB Series User’s Manual
Hardware Installation
Hardware Installation
Installing the CB Series module is easy. Before inserting the module into the PC/104-Plus slot,
you must first configure the I/O base address, interrupt vector, IRQ, and serial interface (for select
models).
ATTENTION
Safety First!
To prevent damage to your system or board, make sure your embedded PC’s power is turned off
before installing your CB Series module.
Step 1: Shut off power to your embedded PC and to any peripheral devices. After shutting off
power, remove the cover of your embedded PC.
Step 2: Use the DIP switches on the module to select the serial interface. Details for each model
are provided later in this chapter.
Step 3: Insert the module firmly into the embedded PC’s PC/104-Plus slot.
Step 4: Screw the control board in place.
Step 5: Connect the cables.
Step 6: Power on the embedded PC. The BIOS will automatically set the IRQ and I/O address
Step 7: Proceed with the software installation. Please refer to Chapter 3.
Block Diagrams
CB-108
Rotary Switch
PC/104-Plus Slot
Box Header Connectors
PC/104 Slot
2-2
CB Series User’s Manual
Hardware Installation
CB-114
Rotary switch
PC/104-Plus Slot
SW1
SW2 Serial Interface
SW3
Box Header Connector
PC/104 Slot
CB-134I
Rotary Switch
PC/104-Plus Slot
RS422/485
2-wire/4-wire
Box Header Connector
PC/104 Slot
Rotary Switch
A rotary switch on the board makes it easy to set the appropriate signals, particularly when
installing multiple PC/104-Plus modules in the same unit. The rotary switch, which looks like a
clock, provides a bi-directional path with no signal propagation delay. The first module on the
stack should be set to CLK0, the second to CLK1, etc., to eliminate clock skew between modules.
Serial Interface Selection
For the CB-114 and CB-134I, the serial interface is selecting using the onboard DIP switches.
CB-114
Mode
S1
S2
S3
RS-232
---
---
ON
RS-422
---
ON
off
4-wire RS-485
ON
off
off
2-wire RS-485
off
off
off
2-3
CB Series User’s Manual
Hardware Installation
CB-134I
Mode
S1
S2
RS-422
---
off
4-wire RS-485
off
ON
2-wire RS-485
ON
ON
2-4
3
Software Installation
Chapter 3
After installing the CB Series module in your embedded computer, the next step is installing the
software. Drivers for various operating systems are provided, including DOS, Windows, and
Linux. This chapter explains how to install and remove the CB Series driver.
The following topics are covered in this chapter:
‰ Windows Vista (32-bit and 64-bit)
¾ Installing the Driver
¾ Using Device Manager to Verify
Installation
¾ Port Configuration
‰ Windows XP, 2003 (32-bit and 64-bit)
¾ Installing the Driver
¾ Using Device Manager to Verify
Installation
¾ Port Configuration
‰ Windows XP, 2003 (32-bit and 64-bit)
¾ Installing the DriverUsing Device
Manager to Verify Installation
¾ Port Configuration
¾ Using PComm
¾ Using Event Log
¾ Disabling the Module
¾ Uninstalling the Module
‰ Windows 2000
¾ Installing the Driver
¾ Using Device Manager to Verify
Installation
¾ Port Configuration
¾ Using PComm
¾ Using Event Log
¾ Disabling the Module
¾ Uninstalling the Module
‰ Linux (32-bit and 64-bit)
‰ DOS
¾ Installing the Driver
¾ Driver Setup
¾ Loading the Driver
¾ Unloading the Driver
‰ Windows CE 5.0
¾ Installing the driver
CB Series User’s Manual
Software Installation
Windows Vista (32-bit and 64-bit)
The Windows Vista (32-bit/64-bit) drivers conform to the Win32 COMM API standard and
support all models in the CB Series. In the following instructions, the CB-114 is used as an
example.
Installing the Driver
1. After the module has been plugged into a PC/104-Plus slot, turn the embedded computer on.
2. Windows will automatically detect the new module and the Found New Hardware Wizard
will open automatically. Select Locate and install driver software (recommended).
3. When prompted to insert the disc, select I don’t have the disc. Show me other options.
3-2
CB Series User’s Manual
Software Installation
4. Select Browse my computer for drier software (advanced).
5. Click Browse to manually specify the folder in which to find the driver. For 32-bit (x86)
platforms, select the \CB Series\Software\Windows Vista\x86 folder on the CD. For 64-bit
(x64) platforms, select the \CB Series\Software\Windows Vista\x64 folder on the CD. Click
Next to continue.
3-3
CB Series User’s Manual
Software Installation
6. If you see a warning that the software has not passed Windows Logo testing, click Install this
driver software anyway.
3-4
CB Series User’s Manual
Software Installation
7. After the files have been installed, click Close.
8. After the module is installed, you will be prompted to install the new serial ports. A Found
New Hardware Wizard window will open for the first serial port, port 0. Select Locate and
install driver software (recommended) to continue.
3-5
CB Series User’s Manual
Software Installation
9. Select I don’t have the disc. Show me other options.
10. Select Browse my computer for driver software (advanced).
3-6
CB Series User’s Manual
Software Installation
11. Click Browse to manually specify the folder in which to find the driver. For 32-bit (x86)
platforms, select the \CB Series\Software\Windows Vista\x86 folder on the CD. For 64-bit
(x64) platforms, select the \CB Series\Software\Windows Vista\x64 folder on the CD. Click
Next to continue.
12. Windows will install the driver software.
13. If you see a warning that the software has not passed Windows Logo testing, click Install this
driver software anyway.
3-7
CB Series User’s Manual
Software Installation
14. After the files have been installed, click Close. The remaining serial ports will automatically
install in the background.
Using Device Manager to Verify Installation
You can use Windows Device Manager to verify proper installation of the CB Series module. In
the following instructions, the CB-114 is used as an example.
1. Under My Computer, click System Properties.
3-8
CB Series User’s Manual
Software Installation
2. In the System window, click Device Manager.
3. In the Device Manager window, you should see your CB Series module under Multi-port
serial adapters. You should also see MOXA communication ports under Ports (COM &
LPT).
3-9
CB Series User’s Manual
Software Installation
4. If you see any special marks, such as a question mark or an exclamation mark, next to the
MOXA items, the installation of your module or serial ports was not successful. Examine the
Windows event log for details.
Port Configuration
After the driver is installed, a CB Series Properties window will appear. The system will map the
serial ports automatically. It will prompt you to take care of port configuration if another CB
Series module has been installed on the PC.
1. Select a specific port under the Port Configuration tab and click Port Setting.
2. Under Port Number, select a COM number to assign to the serial port.
3-10
CB Series User’s Manual
Software Installation
Select Auto Enumerating COM Number to map subsequent ports in numerical order. For
example, if COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
Tx FIFO
Rx FIFO
High
128 bytes
120 bytes
Middle
64 bytes
60 bytes
Low
1 byte
1 byte
Select an Rx FIFO Trigger. The default value is 120 bytes (high level). Select Set the
change to all ports to use this setting for all serial ports on the module.
Select a Tx FIFO Size. The default value is 128 bytes (high level). Select Set the change to
all ports to use this setting for all serial ports on the module.
3. Click OK to approve the port settings. Click OK again to close the CB Series Properties
window and apply the new port settings.
Windows XP, 2003 (32-bit and 64-bit)
The Windows XP and 2003 (32-bit and 64-bit) drivers conform to the Win32 COMM API
standard and support all models in the CB Series. In the following instructions, the CB-114 is used
as an example.
Installing the Driver
1. After the module has been plugged into a PC/104-Plus slot, turn the embedded computer on.
2. Windows will automatically detect the new module and the Found New Hardware Wizard
will open automatically. Select No, not this time and click Next.
3-11
CB Series User’s Manual
Software Installation
3. Select Install from a list or specific location (Advanced) and click Next to continue.
4. Click Browse to manually specify the folder in which to find the driver. For 32-bit (x86)
platforms, select the \CB Series\Software\Windows XP_2003\x86 folder on the CD. For
64-bit (x64) platforms, select the \CB Series\Software\Windows XP_2003\x64 folder on the
CD. Click Next to continue.
3-12
CB Series User’s Manual
Software Installation
5. If you see a warning that the software has not passed Windows Logo testing, click Continue
Anyway.
6. Windows will install the drivers. When the installation is complete, click Finish.
3-13
CB Series User’s Manual
Software Installation
7. After the module is installed, you will be prompted to install the new serial ports. A Found
New Hardware Wizard window will open for the first serial port, port 0. Select No, not this
time and click Next.
8. Select Install from a list or specific location (Advanced) and click Next.
3-14
CB Series User’s Manual
Software Installation
9. Select Search for the best driver in these locations and Include this location in the search.
For 32-bit (x86) platforms, select the \CB Series\Software\Windows XP_2003\x86 folder on
the CD. For 64-bit (x64) platforms, select the \CB Series\Software\Windows XP_2003\x64
folder on the CD. Click Next to continue.
10. If you see a warning that the software has not passed Windows Logo testing, click Continue
Anyway.
3-15
CB Series User’s Manual
Software Installation
11. Windows will install the necessary drivers.
12. After the installation is complete, click Finish.
13. Repeat the installation process for the remaining serial ports.
3-16
CB Series User’s Manual
Software Installation
Using Device Manager to Verify Installation
You can use Windows Device Manager to verify proper installation of the CB Series module. In
the following instructions, the CB-114 is used as an example.
1. Right-click My Computer and select Properties in the context menu.
2. In the Hardware tab, click Device Manager.
3-17
CB Series User’s Manual
Software Installation
3. In the Device Manager window, you should see your CB Series module under Multi-port
serial adapters. You should also see MOXA communication ports under Ports (COM &
LPT).
4. If you see any special marks, such as a question mark or an exclamation mark, next to the
MOXA items, the installation of your module or serial ports was not successful. Examine the
Windows event log for details.
Port Configuration
After the driver is installed, a CB Series Properties window will appear. The system will map the
serial ports automatically. It will prompt you to take care of port configuration if another CB
Series module has been installed on the PC.
1. Select a specific port under the Port Configuration tab and click Port Setting.
3-18
CB Series User’s Manual
Software Installation
2. Under Port Number, select a COM number to assign to the serial port.
Select Auto Enumerating COM Number to map subsequent ports in numerical order. For
example, if COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
Tx FIFO
Rx FIFO
High
128 bytes
120 bytes
Middle
64 bytes
60 bytes
Low
1 byte
1 byte
Select an Rx FIFO Trigger. The default value is 120 bytes (high level). Select Set the
change to all ports to use this setting for all serial ports on the module.
Select a Tx FIFO Size. The default value is 128 bytes (high level). Select Set the change to
all ports to use this setting for all serial ports on the module.
3. Click OK to approve the port settings. Click OK again to close the CB Series Properties
window and apply the new port settings.
3-19
CB Series User’s Manual
Software Installation
Using PComm
PComm Diagnostic is a useful program for checking the module’s status. It provides internal and
external testing of IRQ, TxD/RxD, UART, CTS/RTS, DTR/DSR, and other items. You can use
PComm Diagnostic to verify that the module and serial ports are working properly.
You can download the free version of PComm at Moxa’s website (www.moxa.com).
Using Event Log
You may refer to the Windows event log to verify operation of the module. To view the event log,
open Event Viewer, which is located under Administrative Tools in the Control Panel. Information
about the module will be located under the System category.
Disabling the Module
1. Right-click My Computer and select Properties in the context menu.
2. In the Hardware tab, click Device Manager.
3-20
CB Series User’s Manual
Software Installation
3. In Device Manager, right-click your module under Multi-port serial adapters and select
Disable in the context menu. This will disable the module.
Uninstalling the Module
1. Right-click My Computer and select Properties in the context menu.
2. In the Hardware tab, click Device Manager.
3-21
CB Series User’s Manual
Software Installation
3. Right-click your module under Multi-port serial adapters and select Uninstall in the context
menu.
4. A confirmation dialog will appear. Click OK to uninstall the device.
Windows 2000
The Windows 2000 drivers conform to the Win32 COMM API standard and support all models in
the CB Series. In the following instructions, the CB-114 is used as an example.
Installing the Driver
1. After the module has been plugged into a PC/104-Plus slot, turn the embedded computer on.
2. Windows will automatically detect the new module and the Found New Hardware Wizard
will open automatically. Click Next to continue.
3-22
CB Series User’s Manual
Software Installation
3. Select Search for a suitable driver for my device (recommended) and click Next to
continue.
4. Select Specify a location and click Next to continue.
3-23
CB Series User’s Manual
Software Installation
5. Click Browse to manually specify the folder in which to find the driver. Select the \CB
Series\Software\Windows 2K folder on the CD and click Next to continue.
6. To begin installing the module, click Next.
7. If you see a warning that the Microsoft digital signature was not found, click Yes to proceed
with the installation.
3-24
CB Series User’s Manual
Software Installation
8. Windows will install the drivers. When the installation is complete, click Finish.
9. After the module is installed, you will be prompted to install the new serial ports. A Found
New Hardware Wizard window will open for the first serial port, port 0. Click Next to
proceed.
3-25
CB Series User’s Manual
Software Installation
10. Select Search for a suitable driver for my device [recommended] and click Next.
11. Select Specify a location and click Next.
12. Select the \CB Series\Software\Windows 2K folder on the CD and click Next.
3-26
CB Series User’s Manual
Software Installation
13. When the driver has been found, click Next to proceed.
14. Windows will install the necessary drivers. After the installation is complete, click Finish.
The remaining serial ports will be installed automatically in the background.
3-27
CB Series User’s Manual
Software Installation
Using Device Manager to Verify Installation
You can use Windows Device Manager to verify proper installation of the CB Series module. In
the following instructions, the CB-114 is used as an example.
1. Right-click My Computer and select Properties in the context menu.
2. In the Hardware tab, click Device Manager.
3. In the Device Manager window, you should see your CB Series module under Multi-port
serial adapters. You should also see MOXA communication ports under Ports (COM &
LPT).
3-28
CB Series User’s Manual
Software Installation
4. If you see any special marks, such as a question mark or an exclamation mark, next to the
MOXA items, the installation of your module or serial ports was not successful. You can
check the Windows event log for details.
Port Configuration
After the driver is installed, a CB Series Properties window will appear. The system will map the
serial ports automatically. It will prompt you to take care of port configuration if another CB
Series module has been installed on the PC.
1. Select a specific port under the Port Configuration tab and click Port Setting.
2. Under Port Number, select a COM number to assign to the serial port.
3-29
CB Series User’s Manual
Software Installation
Select Auto Enumerating COM Number to map subsequent ports in numerical order. For
example, if COM 3 is assigned to Port 1, then COM 4 will be automatically assigned to Port 2.
Tx FIFO
Rx FIFO
High
128 bytes
120 bytes
Middle
64 bytes
60 bytes
Low
1 byte
1 byte
Select an Rx FIFO Trigger. The default value is 120 bytes (high level). Select Set the
change to all ports to use this setting for all serial ports on the module.
Select a Tx FIFO Size. The default value is 128 bytes (high level). Select Set the change to
all ports to use this setting for all serial ports on the module.
3. Click OK to approve the port settings. Click OK again to close the CB Series Properties
window and apply the new port settings.
Using PComm
PComm Diagnostic is a useful program for checking the module’s status. It provides internal and
external testing of IRQ, TxD/RxD, UART, CTS/RTS, DTR/DSR, and other items. You can use
PComm Diagnostic to verify that the module and serial ports are working properly.
3-30
CB Series User’s Manual
Software Installation
The free version of PComm is available at Moxa’s website (www.moxa.com).
Using Event Log
You may refer to the Windows event log to verify operation of the module. To view the event log,
open Event Viewer, which is located under Administrative Tools in the Control Panel. Information
about the module will be located under the System category.
Disabling the Module
1. Right-click My Computer and select Properties in the context menu.
2. In the Hardware tab, click Device Manager.
3-31
CB Series User’s Manual
Software Installation
3. In Device Manager, right-click your module under Multi-port serial adapters and select
Disable in the context menu. This will disable the module.
Uninstalling the Module
1. Right-click My Computer and select Properties in the context menu.
2. In the Hardware tab, click Device Manager.
3-32
CB Series User’s Manual
Software Installation
3. Right-click your module under Multi-port serial adapters and select Uninstall in the context
menu.
4. A confirmation dialog will appear. Click OK to uninstall the device.
3-33
CB Series User’s Manual
Software Installation
Linux (32-bit and 64-bit)
Execute the following commands from the Linux prompt:
#mount /dev/cdrom /mnt/cdrom
#cd /
#mkdir moxa
#cd moxa
#cp /mnt/cdrom/<driver directory>/mxser.tgz .
#tar xvfz mxser.tgz
#cd mxser
# make clean; make install
#cd /moxa/mxser/driver
#./msmknod
#modprobe mxser
You can use the Moxa diagnostic utility to verify the driver status:
#cd /moxa/mxser/utility/diag
#./msdiag
You can use the Moxa terminal utility to test the tty ports:
#cd /moxa/mxser/utility/term
#./msterm
DOS
MOXA DOS API-232 is a software package that can help you develop or debug serial
communications programs. This section will explain how to install the package, set up the driver,
and load or unload the driver. For additional information about the API-232 library and utilities,
please refer to Chapter 4.
The DOS drivers support all models in the CB Series.
In the following instructions, the CB-104 is used as an example.
Installing the Driver
Run the installation program, DOSINST.EXE, in the DOS folder. Specify the target directory for
the API-232 files (e.g., C:\MOXA). Press F2 to start the installation.
3-34
CB Series User’s Manual
Software Installation
After installation is complete, you will be prompted to set up the board and driver initial values.
We strongly recommended that you do so.
Driver Setup
The following instructions are not intended to illustrate every function of the setup program. For
more detailed information, please refer to the help files by pressing F1 in the setup program.
1. Run the setup program, BIN\SETUP.EXE.
2. Select your CB Series model and press Enter.
3. A window will open displaying all configuration information for all installed modules. Press
PgDn to view advanced port setup options and to make configuration changes. Your module’s
configuration will be displayed along with other settings such as port number, buffer size, etc.
4. Verify the settings and make any necessary changes.
3-35
CB Series User’s Manual
Software Installation
Port number:
This is the port ID of each port. Application software will refer to a port
by its port number (ID). Port numbers must be unique; duplicate port
numbers are not allowed. The port ID can range from 0 to 127 as long as
it does not overlap with another port. Generally, you should consider the
convenience of programming when specifying the port number.
TxD buffer size:
This is the transmission (output) buffer allocated in the system for each
port.
RxD buffer size:
This is the receiving (input) buffer allocated in the system for each port.
F5: Group Edit:
This allows you to configure several ports simultaneously as a group.
5. Press F10 to save the latest configuration and exit the setup program.
3-36
CB Series User’s Manual
Software Installation
Loading the Driver
After setting up the driver, you must load the driver in order to gain access to the serial ports on
the module. Run BIN\DPC-DRV.EXE at the DOS prompt. The driver will detect your CB Series
module automatically. You should see messages indicating successful detection of your module,
such as the following:
Smartio/Industio Family DOS driver Version 1.8
Setup driver …
CB-114 series (Bus=x, Dev=y) : OK!
Device driver setup O.K.
At this point, you can execute applications that support API-232 functions, or start developing
applications using the API-232 library.
Unloading the Driver
To unload or release the CB Series driver from memory, enter DPC-DRV/Q at the DOS prompt.
Windows CE 5.0
In this section, we explain how to install Moxa CB series boards under WinCE 5.0. These
instructions are intended for users who are familiar with the Windows CE Platform Builder 5.0
Toolkit, and would like to install one or more Moxa Tech products. Here, we only give the
step-by-step installation instructions for the development environment. You will need to download
the image file to the target host yourself.
The WinCE 5.0 driver for the MOXA CB Series PC/104-Plus Multiport Serial Module supports
the following products:
y CB Series: CB-108, CB-114, CB-134I
The CB-114 board is used to illustrate the installation procedure.
Installing the driver
The following procedure explains how to install the CB-114 multiport serial module driver under
WinCE.
1. Obtain a copy of MOXA Tech WinCE 5.0 driver package and extract it to your computer.
Double click the Install package to copy the Mxser folder to
%WINCEROOT%\PLATFORM\ automatically, and import the supported MOXA Tech
products into the Folder.
3-37
CB Series User’s Manual
Software Installation
2. Start WinCE Platform Builder, select File, and open New Platform.
3. Enter a Name for Workspace and press Next.
3-38
CB Series User’s Manual
Software Installation
4. When you see Board Support Packages, Design Template, Applications & Media,
Networking & Communications, OBEX Server, select what you need to build your own
environment. The Completing the New Platform Wizard window will open to indicate that
it has finished creating a new platform. Click Finish to complete the setup.
3-39
CB Series User’s Manual
Software Installation
3-40
CB Series User’s Manual
Software Installation
5. Open Manage Catalog Items (File Æ Manage Catalog Items). In the Catalog (View Æ
Catalog), browse to \Third Party\Device Drivers\ MOXA Smartio/Industio-PCI,
PC/104-Plus. Right-click on the driver Prefix COM or Prefix MXU you would like to
include and choose Add to OS Design.
Note: You can only select either Prefix COM or Prefix MXU, but not both.
Prefix COM supports up to 10 ports, from COM0 to COM9. Prefix MXU supports more than
10 ports, so it is better for you to select Prefix MXU if you are not sure how many ports the
device has. Otherwise, you will only be allowed to use one multiport serial board on the target
host.
3-41
CB Series User’s Manual
Software Installation
6. After adding MOXA Tech drivers into your OS Design, a new project is automatically added
to your workspace. The project name is mxserce5. The project can be accessed from File
View (View Æ File View). The mxserce5 project contains a number of files used to configure
the drivers included in your OS Design.
Note: If you would like to use “Terminal Emulator” tool, please modify mxserce5.reg and
keyboard like below (This is only just for “one” “COM” port). You have to notice number of
ports, COM, MXU and enter the correct information.
[HKEY_LOCAL_MACHINE\ExtModems\HayesCompat1]
“Port”=”COM2:”
“DeviceType”=dword:1
“FriendlyName”=”Hayes Compatible on COM2:”
7. Finally, open Build OS, select Build and Sysgen, and be sure to click Copy Files to Release
Directory After Build and Make Run-Time Image After Build.
3-42
CB Series User’s Manual
Software Installation
8. Finally, copy your image file to the target Host.
Note: If you have created a Windows CE Platform Builder in the development environment, you
can skip steps 2, 3, and 4.
3-43
4
Serial Programming Tools
Chapter 4
MOXA provides Windows serial programming libraries and troubleshooting utilities that are easy
to use and powerful. You can use these tools to reduce software development time.
The serial communication library is useful for developing applications for data communications,
remote access, data acquisition, and industrial control. It provides a simpler solution compared to
the more complex Windows Win32 COMM API.
PComm is a professional serial communication tool for Windows PCs. PComm includes the
following features:
y Useful utilities for diagnostics, port monitoring, and terminal emulation
y Sample programs
y Comprehensive help files
The following topics are covered in this chapter:
‰ Serial Programming Library
‰ PComm Utilities
¾ Installation
¾ PComm Diagnostic
¾ PComm Monitor
¾ PComm Terminal Emulator
CB Series User’s Manual
Serial Programming Tools
Serial Programming Library
The serial programming library assists you in developing serial communications programs for any
COM port that complies with the Microsoft Win32 API. It facilitates the implementation of
multi-process and multi-thread serial communication programs and can remarkably reduce
development time.
The library provides a complete set of functions as well as various sample programs for Visual
C++, Visual Basic, and Delphi. To view detailed descriptions of the available functions and
sample programs, go to Start Æ Program Æ PComm Lite and select PComm Lib Help,
PComm Porting Notes, or PComm Programming Guide. You may also refer to the sample
programs in the PComm directory.
PComm Utilities
This section provides brief descriptions of the PComm utilities. For more information about these
utilities, please refer to the help files or to the API-232.txt file for DOS.
Installation
To install PComm, run Setup.exe from the installation diskette. Please note that the PComm
diagnostic and monitor utilities are for MOXA boards only. These two utilities will not work with
other serial boards.
PComm Diagnostic
PComm Diagnostic is designed for MOXA boards only. It provides internal and external testing of
IRQ, TxD/RxD, UART, CTS/RTS, DTR/DSR, DTR/DCD, and other items. You can use PComm
Diagnostic to check the operation of both software and hardware.
To run the Diagnostic program, go to Start Æ Program Æ PComm Lite Æ Diagnostic.
4-2
CB Series User’s Manual
Serial Programming Tools
PComm Monitor
PComm Monitor is designed for MOXA board in Windows NT only. It allows you to monitor data
transmission of selected MOXA COM ports. It monitors data transmission, throughput, and line
status at regular intervals. Click on a specific port to view that port’s communication parameters
and status.
To run PComm Monitor, go to Start Æ Program Æ PComm Lite Æ Monitor.
PComm Terminal Emulator
PComm Terminal Emulator can be used to connect to a serial port to verify that data transmission
is functioning correctly. It supports multiple windows and both VT100 and ANSI terminal types.
You can interactively transfer data, periodically send patterns, and transfer files using ASCII,
XMODEM, YMODEM, ZMODEM, and KERMIT protocols.
To run PComm Terminal Emulator, go to Start Æ Program Æ PComm Lite Æ Terminal
Emulator.
4-3
CB Series User’s Manual
Serial Programming Tools
4-4
5
Pin Assignments
Chapter 5
The box header connector(s) on the module is used to connect to serial devices. Optional cables
are available that provide DB9 or DB25 connectors. The pin assignments of the box header
connectors and available cables are provided below.
Box Header Pin Assignments
RS-232
These pin assignments apply to the CB-108 and CB-114. Note that there are two 40-pin box
header connectors on the CB-108, each of which connects to 4 serial ports.
Pin Signal Pin Signal Pin Signal Pin Signal
1
DCD0
11
DCD1
21
DCD2
31
DCD3
2
DSR0
12
DSR1
22
DSR2
32
DSR3
3
RxD0
13
RxD1
23
RxD2
33
RxD3
4
RTS0
14
RTS1
24
RTS2
34
RTS3
5
TxD0
15
TxD1
25
TxD2
35
TxD3
6
CTS0
16
CTS1
26
CTS2
36
CTS3
7
DTR0
17
DTR1
27
DTR2
37
DTR3
8
---
18
---
28
---
38
---
9
GND0
19
GND1
29
GND2
39
GND3
10
---
20
---
30
---
40
---
RS-422, 4-wire RS-485
These pin assignments apply to the CB-114 and CB134I.
Pin
Signal
Pin
1
TxD0-(A)
11
3
TxD0+(B) 13 TxD1+(B) 23 TxD2+(B) 33 TxD3+(B)
5
RxD0+(B) 15 RxD1+(B) 25 RxD2+(B) 35 RxD3+(B)
7
RxD0-(A) 17 RxD1-(A) 27 RxD2-(A) 37 RxD3-(A)
9
GND0
19
Signal
Pin
Signal
Pin
Signal
TxD1-(A) 21 TxD2-(A) 31 TxD3-(A)
GND1
29
GND2
39
GND3
CB Series User’s Manual
Pin Assignments
2-wire RS-485
These pin assignments apply to the CB-114 and CB134I.
Pin
Signal
Pin
Signal
Pin
Signal
Pin
Signal
5
Data0+(B) 15 Data1+(B) 25 Data2+(B) 35 Data3+(B)
7
Data0-(A) 17 Data1-(A) 27 Data2-(A) 37 Data3-(A)
9
GND0
19
GND1
29
GND2
39
GND3
Serial Cable Pin Assignments
DB9(M) Connectors
1
6
5
9
The CBL-F40M9x4-50 and CBL-F20M9x4-50 cables provide DB9(M) connectors for each serial
port, with pin assignments as follows:
RS-422
Pin RS-232 4-wire RS-485 2-wire RS-485
1
DCD
TxD-(A)
---
2
RxD
TxD+(B)
---
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
7
RTS
8
CTS
5-2
CB Series User’s Manual
Pin Assignments
DB25(M) Connectors
1
13
14
25
The CBL-F40M25x4-50 and CBL-F20M25x4-50 cables provide DB25(M) connectors for each
serial port, with pin assignments as follows:
Pin RS-232
RS-422
4-wire RS-485 2-wire RS-485
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
---
4
RTS
---
---
5
CTS
---
---
6
DSR
---
---
7
GND
GND
GND
8
DCD
TxD-(A)
---
20
DTR
RxD-(A)
Data-(A)
5-3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement