"user manual"
User’s Manual
Ver. 1.01
IMPORTANT
• Read this manual thoroughly, and do not perform installation,
operation, maintenance, or inspection unless you fully
understand all of the contents.
• Keep this manual in a safe place where you can refer to it
easily while installing, operating, and carrying out
maintenance or inspections.
RS-61004-11 1.01
© ISHIDA Co., Ltd. 2008 All rights are reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means
mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA.
NOTICES
NOTICES
IMPORTANT NOTICE
Those who handle the machine must be aware of the hazards involved. These dangers may not be
obvious, so it is imperative to follow the instructions detailed in this manual when installing, operating,
inspecting, or servicing the machine. Therefore, we recommend that you thoroughly read and
understand this manual before installing, operating, inspecting, or servicing the machine.
ISHIDA is not liable for any damage, loss or injury that results from incorrect operation, insufficient
caution, unauthorized modifications to the machine, or failure to follow the instructions contained in
this manual.
LIMITATIONS OF LIABILITY
ISHIDA assumes no responsibility for special, indirect, or consequential damages, loss of profits or
commercial loss in any way connected with the machine, whether such claim is based on contract,
warranty, negligence, or strict liability.
ISHIDA assumes no responsibility for the user's programming of this machine, or any consequence
thereof.
In no event shall ISHIDA be responsible for warranty, repair, or other claims regarding the machine
unless ISHIDA’s analysis confirms that the machines were properly handled, stored, installed, and
maintained and not subject to contamination, abuse, misuse, or inappropriate modification or repair.
CHANGE IN SPECIFICATIONS
Machine specifications and accessories may be changed at any time due to improvements or other
reasons. Consult with your ISHIDA representative at any time to confirm the actual specifications of
the purchased machine.
ERRORS AND OMISSIONS
The information in this manual has been carefully checked and is believed to be accurate; however,
no responsibility is assumed for clerical, typographical or proofreading errors, or omissions.
UNI-7 User’s Manual
i
PRECAUTIONS FOR SAFE USE
PRECAUTIONS FOR SAFE USE
It is strongly advised that the following safety measures must be observed to ensure the safe
operation of the machine.
• Prepare a dedicated power source and always use a
power supply with rated voltage. Never connect the
machine power input with an AC power supply
exceeding the rated voltage. To avoid any potential
electrical shock, ensure that the protective ground
wire is connected to the main grounding provision.
A power supply that generates voltage variation may
cause a malfunction, or using the machine outside of the
rated voltage may result in machine failure or danger
such as electric shock.
• Do not install the machine near a TV set or radio.
Doing so may cause static to the TV set and/or radio as
this machine emits week electric wave.
• Do not allow water or any liquids to come into
contact with the machine.
Doing so may result in fire or cause the machine to break
down.
• Do not drop or apply a strong shock to the machine.
Doing so may cause the machine to break down.
• Do not disassemble, modify, or attempt to repair the
machine.
Doing so may damage the original safety functions.
• Do not hold the connector cover when carrying the
machine.
Dropping the machine may result in injury or cause the
machine to break down.
ii
UNI-7 User’s Manual
PRECAUTIONS FOR SAFE USE
• Do not hold the operation panel or weigh platter
when carrying the machine.
Doing so may cause the operation panel or the platter to
break down.
• Do not hold the customer display for the pole type
when carrying the machine.
Dropping the machine may result in injury or cause the
machine to break down.
• Handle with care when removing or inserting the
cassette.
Careless cassette handling may result in injury or cause
the cassette to break down.
• Do not drop the cassette.
Dropping the cassette may result in injury or cause the
cassette to break down.
• Do not press the touch panel with an edged thing.
Doing so may scratch the panel and cause the machine
to break down.
• Risk of explosion if battery is replaced by an
incorrect type. Make sure to dispose of used
batteries according to the instructions.
UNI-7 User’s Manual
iii
PRECAUTIONS FOR MACHINE INSTALLATION
PRECAUTIONS FOR MACHINE INSTALLATION
Do not install the machine in the following types of places:
• Places subject to high
temperatures or high humidity
• Places exposed to direct
sunlight
• Places subject to excessive
vibration or unstable
foundations
• Places exposed to direct cold
air from air conditioners or
refrigerators
• Places subject to a lot of
dust or dirt
• Places with large voltage
fluctuations
• Places where water or other
liquids are easily spilled on the
• Places where the floor or
machine
foundation is unstable
iv
UNI-7 User’s Manual
PRECAUTION SYMBOLS
PRECAUTION SYMBOLS
This machine is manufactured for use according to proper procedures by a qualified person and only
for the purposes described in this manual. The following conventions are used to indicate and classify
precautions depending on the level of danger, or seriousness of potential injury. Always heed the
information provided in this manual. Failure to heed precautions can result in personal injury or
property damage.
The following precaution symbols are used in this manual.
Indicates a potentially hazardous situation which, if not avoided, may result in
serious injury or death. Additionally, there may be significant property damage.
Indicates a potentially hazardous situation where, if not avoided, may result in
minor or moderate injury or in property damage.
Indicates reference information for operation.
Indicates the referred page for operation.
UNI-7 User’s Manual
v
TABLE OF CONTENTS
TABLE OF CONTENTS
CHAPTER 1
1.1
SPECIFICATIONS ................................................................................................... 1-1
1.2
MODEL VARIATIONS .............................................................................................. 1-2
1.3
PART NAMES AND FUNCTIONS............................................................................ 1-3
1.3.1
FRONT VIEW (BENCH TYPE).................................................................... 1-3
1.3.2
REAR VIEW (BENCH TYPE) ...................................................................... 1-3
1.4
OPERATION PANEL................................................................................................ 1-4
1.5
ADJUSTMENTS ...................................................................................................... 1-5
1.5.1
LEVEL ADJUSTMENT (BENCH TYPE) ...................................................... 1-5
1.5.2
OPERATION PANEL ANGLE ADJUSTMENT (BENCH TYPE) ................... 1-5
1.6
LABEL / RECEIPT ROLL LOADING ........................................................................ 1-6
1.7
REMOVING & REPLACING OF WEIGH PLATTER ................................................ 1-9
1.8
1.9
1.7.1
REMOVING THE WEIGH PLATTER........................................................... 1-9
1.7.2
REPLACING THE WEIGH PLATTER.......................................................... 1-9
CLEANING OF THE MACHINE ............................................................................. 1-10
1.8.1
CLEANING OF THE THEREMAL HEAD................................................... 1-10
1.8.2
CLEANING OF THE LABEL SENSOR ...................................................... 1-11
1.8.3
CLEANING OF THE PRINT ROLLER AND PRISM .................................. 1-12
1.8.4
PRECAUTIONS WHEN USING CLEANING FLUIDS ............................... 1-13
STARTING PROCEDURES................................................................................... 1-14
1.9.1
TURNING ON THE POWER ..................................................................... 1-14
1.9.2
PERFORMING ZERO ADJUSTMENT ...................................................... 1-15
1.9.3
GETTING BACK TO THE INITIAL SCREEN ............................................. 1-16
CHAPTER 2
2.1
2.2
2.3
LABEL/RECEIPT ISSUE ................................................................................... 2-1
LABEL ISSUE WITHOUT OPERATOR.................................................................... 2-1
2.1.1
WEIGHING UNIT PRICE PRODUCTS........................................................ 2-1
2.1.2
WEIGHING FIXED PRICE PRODUCTS ..................................................... 2-4
2.1.3
PROCESSING FIXED PRICE PRODUCTS ................................................ 2-7
2.1.4
PROCESSING FIXED WEIGHT/FIXED UNIT PRICE PRODUCTS ............ 2-9
LABEL ISSUE WITH OPERATORS....................................................................... 2-11
2.2.1
WEIGHING UNIT PRICE PRODUCTS...................................................... 2-11
2.2.2
WEIGHING FIXED PRICE PRODUCTS ................................................... 2-14
2.2.3
PROCESSING FIXED PRICE PRODUCTS .............................................. 2-17
2.2.4
PROCESSING FIXED WEIGHT/FIXED UNIT PRICE PRODUCTS .......... 2-19
RECEIPT ISSUE.................................................................................................... 2-21
CHAPTER 3
vi
BEFORE USE .................................................................................................... 1-1
TRACEABILITY PRODUCTS ............................................................................ 3-1
3.1
REFERING TO PREVIOUS TRACEABILITY DATA................................................. 3-1
3.2
CHANGING TRACEABILITY DATA ......................................................................... 3-4
UNI-7 User’s Manual
TABLE OF CONTENTS
CHAPTER 4
TEMPORARY CHANGE OPERATIONS ........................................................... 4-1
4.1
UNIT PRICE CHANGE ............................................................................................ 4-1
4.2
FIXED PRICE CHANGE .......................................................................................... 4-3
4.3
AMOUNT DISCOUNT FOR UNIT PRICE ................................................................ 4-5
4.4
PERCENT DISCOUNT FOR UNIT PRICE .............................................................. 4-7
4.5
AMOUNT DISCOUNT FOR TOTAL PRICE ............................................................. 4-9
4.6
PERCENT DISCOUNT FOR TOTAL PRICE.......................................................... 4-11
4.7
PRODUCT QUANTITY CHANGE .......................................................................... 4-13
4.8
PRINT QUANTITY SETTING................................................................................. 4-15
CHAPTER 5
SELF-SERVICE OPERATIONS......................................................................... 5-1
5.1
WEIGHING PRODUCTS ......................................................................................... 5-1
5.2
FIXED PRICE PRODUCTS ..................................................................................... 5-3
CHAPTER 6
ACCUMULATOR MODE ................................................................................... 6-1
6.1
MANUAL INPUT ACCUMULATION ......................................................................... 6-1
6.2
WEIGHING ACCUMULATION ................................................................................. 6-3
6.3
MANUAL INPUT VOID............................................................................................. 6-6
6.4
WEIGHING VOID..................................................................................................... 6-9
CHAPTER 7
TOTAL ADJUST MODE .................................................................................... 7-1
7.1
MANUAL INPUT SUBTRACTION............................................................................ 7-1
7.2
WEIGHING SUBTRACTION.................................................................................... 7-3
7.3
MANUAL INPUT ADDITION..................................................................................... 7-6
7.4
WEIGHING ADDITION ............................................................................................ 7-9
CHAPTER 8
TOTAL MODE.................................................................................................... 8-1
8.1
DAILY TOTAL........................................................................................................... 8-1
8.2
WEEKLY TOTAL ...................................................................................................... 8-4
8.3
CUMULATIVE TOTAL.............................................................................................. 8-6
8.4
TRACEABILITY TOTAL ........................................................................................... 8-8
8.5
PRESET REPORT PRINTING................................................................................. 8-9
8.6
TOTAL CLEAR....................................................................................................... 8-10
CHAPTER 9
PROGRAM MODE ............................................................................................. 9-1
9.1
PROGRAM MODE ENTRY...................................................................................... 9-1
9.2
PLU FILE REGISTRATION...................................................................................... 9-4
9.3
CAMPAIGN LIST REGISTRATION ........................................................................ 9-14
9.4
OPERATOR REGISTRATION................................................................................ 9-19
9.5
PRESET KEY REGISTRATION ............................................................................. 9-22
9.5.1
SETTING PRESET FUNCTIONS.............................................................. 9-22
9.5.2
ASSIGNING IMAGES ON THE PRESET KEYS ....................................... 9-25
9.5.3
COLORING PRESET KEYS ..................................................................... 9-27
9.5.4
CHANGING PRESET KEY SIZES ............................................................ 9-30
9.5.5
EDITING PRESET KEY NAMES............................................................... 9-33
UNI-7 User’s Manual
vii
TABLE OF CONTENTS
9.5.6
CONFIRMING PRESET KEY DATA .......................................................... 9-36
9.5.7
DELETING PRESET KEYS....................................................................... 9-37
9.5.8
MEMBRANE KEYS ................................................................................... 9-39
9.6
ADVERTISEMENT MESSAGE REGISTRATION .................................................. 9-42
9.7
STORE NAME REGISTRATION............................................................................ 9-46
9.8
9.9
9.7.1
CHANGING EXISTING STORE DATA ...................................................... 9-46
9.7.2
CREATING NEW STORE DATA ............................................................... 9-49
DEPARTMENT NAME REGISTRATION................................................................ 9-53
9.8.1
CREATING NEW DEPARTMENT NAMES................................................ 9-53
9.8.2
CHANGING EXISITING DEPARTMENT NAMES ..................................... 9-57
GROUP NAME REGISTRATION ........................................................................... 9-59
9.9.1
CREATING NEW GROUP NAMES ........................................................... 9-59
9.9.2
CHANGING EXISITING GROUP NAMES................................................. 9-62
9.10 COOKING INSTRUCTION REGISTRATION ......................................................... 9-64
9.10.1 CREATING NEW INSTRUCTIONS ........................................................... 9-64
9.10.2 CHANGING EXISITING INSTRUCTIONS................................................. 9-67
9.11 NUTRITION FILE REIGISTRATION ...................................................................... 9-69
9.11.1 CREATING NEW NUTRITION DATA ........................................................ 9-69
9.11.2 CHANGING EXISTING NUTRITION DATA ............................................... 9-72
9.12 EXTRA MESSAGE REGISTRATION..................................................................... 9-75
9.12.1 CREATING NEW MESSAGES.................................................................. 9-75
9.12.2 CHANGING EXISITING MESSAGES ....................................................... 9-78
9.13 COUPON MESSAGE REGISTRATION ................................................................. 9-80
9.13.1 CREATING NEW MESSAGES.................................................................. 9-80
9.13.2 CHANGING EXISITING MESSAGES ....................................................... 9-83
9.14 POP MESSAGE REGISTRATION ......................................................................... 9-85
9.15 TAX REGISTRATION............................................................................................. 9-87
9.16 SCHEME TABLE REGISTRATION ........................................................................ 9-88
9.16.1 CREATING NEW TABLES ........................................................................ 9-88
9.16.2 CHANGING EXISITING MESSAGES ....................................................... 9-92
9.17 GEN TABLE REGISTRATION................................................................................ 9-96
9.18 LOOKUP TABLE REGISTRATION ........................................................................ 9-99
9.18.1 CREATING NEW TABLES ........................................................................ 9-99
9.18.2 CHANGING EXISITING TABLES ............................................................ 9-106
9.19 MINCE TRACEABILITY REGISTRATION ........................................................... 9-110
9.20 FIXED PRICE MARK REGISTRATION ................................................................9-111
9.20.1 CREATING NEW PRICE MARKS ............................................................9-111
9.20.2 CHANGING EXISITING PRICE MARKS................................................. 9-113
9.21 FREE MESSAGE REGISTRATION ..................................................................... 9-115
9.21.1 CREATING NEW MESSAGES................................................................ 9-115
9.21.2 CHANGING EXISITING MESSAGES ..................................................... 9-118
9.22 CHECK LABEL REGISTRATION......................................................................... 9-120
viii
UNI-7 User’s Manual
TABLE OF CONTENTS
CHPATER 10 SETUP MODE.................................................................................................. 10-1
10.1 SETUP MODE ENTRY .......................................................................................... 10-1
10.2 MACHINE NUMBER SETTING ............................................................................. 10-3
10.3 SALES MODE SETTING ....................................................................................... 10-4
10.4 PASSWORD SETTING.......................................................................................... 10-5
10.5 KEY LOCK SETTING .......................................................................................... 10-10
10.6 DATA STORAGE SETTING ................................................................................. 10-14
10.7 PRESET REPORT SETTING .............................................................................. 10-15
10.8 AUTO PROGRAM SETTING ............................................................................... 10-19
10.9 DEFAULT DATA SETTING................................................................................... 10-21
10.10 PLU UPDATE SETTING ...................................................................................... 10-29
10.11 RECEIPT SETTING............................................................................................. 10-35
CHAPTER 11 ADJUSTMENT MODE ..................................................................................... 11-1
11.1 ADJUSTMENT MODE ENTRY .............................................................................. 11-1
11.2 DATE / TIME ADJUSTMENT ................................................................................. 11-2
11.3 TOUCH PANEL ADJUSTMENT ............................................................................. 11-4
11.4 DISPLAY CHECK .................................................................................................. 11-6
APPENDIX
TEXT EDITING...................................................................................................A-1
A.1
OPERATION PANEL AND KEY FUNCTIONS .........................................................A-1
A.2
NORMAL CHARACTER EDITING ...........................................................................A-3
A.3
SPECIAL CHARACTER EDITING ...........................................................................A-6
A.4
LINE DELETION ......................................................................................................A-8
A.5
CHARACTER DELETION........................................................................................A-9
A.6
CHARACTER BACKSPACING .............................................................................. A-11
UNI-7 User’s Manual
ix
Chapter 1
BEFORE USE
1
BEFORE USE
1.1
SPECIFICATIONS
Items
Descriptions
Use conditions
Temperature: 5 to 35°C
Humidity: 30 to 85%, Non condensing.
Power supply:
AC100 – 240V, 50 / 60Hz
Power consumption
1.0A/0.5A
Weight
Bench type: Approx.11.5 kg
Pole type: Approx.12.5 kg
Weighing capacity
15 kg: 0 to 6/0.002 kg, 6 to 15/0.005 kg
Weighting accuracy
1/3000
Operator/Customer display
7.0 inch color liquid crystal with back light, 480 X 234dots
Printing method
Direct thermal method
Thermal head
2 inches (448dots) and 8 dots/mm
Printing speed
100mm/second, 120mm/second
Note: The printing speed may vary according to label conditions.
Printing effective size
56mm
Label size
Label width: 30mm to 60mm
Label length: 20mm to 150mm
Number of label cassettes
7 cassettes
Input/Output
LAN 1 channel
USB 1 channel
CF 1 channel
Drawer 2 channels
Program store medium
Flash ROM (32M bytes)
UNI-7 User’s Manual
1-1
Chapter 1
1.2
BEFORE USE
MODEL VARIATIONS
Bench Type
Bakery Type
Pole Type
Elevated Type
Self-service Type
1-2
Hanging Type
UNI-7 User’s Manual
Chapter 1
1.3
BEFORE USE
PART NAMES AND FUNCTIONS
1.3.1 FRONT VIEW (BENCH TYPE)
1.3.2 REAR VIEW (BENCH TYPE)
UNI-7 User’s Manual
1-3
Chapter 1
1.4
BEFORE USE
OPERATION PANEL
„ Keys for Usual Use
1-4
Used to delete an entered
numerical value.
Used to display Menu Select
screen.
Used to call a registered product
data.
Used to turn the previous page.
Used to feed labels.
Used to turn the next page.
Used to issue a label.
Used to jump to the top page.
Used to enter tare weight.
Used to jump to the end page.
Used to reset a weigh to zero.
Used to escape from the current
mode.
UNI-7 User’s Manual
Chapter 1
1.5
BEFORE USE
ADJUSTMENTS
1.5.1 LEVEL ADJUSTMENT (BENCH TYPE)
Install the machine horizontally to use.
Be sure to turn off the power switch before placing the machine on a stable platform, and adjust the
machine inclination by turning the four level adjustment feet so that the bubble is located at the center
of the level gauge. Accurate measurements cannot be performed if it is not installed horizontally.
1.5.2 OPERATION PANEL ANGLE ADJUSTMENT (BENCH TYPE)
To obtain a better view, adjust the angle of the operation panel within the range between 0 and 70
degrees.
UNI-7 User’s Manual
1-5
Chapter 1
1.6
1.
BEFORE USE
LABEL / RECEIPT ROLL LOADING
Pull out the cassette from the main body.
Before pulling out the cassette unit, ensure that nothing is placed on the weigh platter.
1-6
2.
Set a new roll around the roll holder and raise the roll stopper to fix the roll position.
3.
Thread the paper as shown in the figures below..
UNI-7 User’s Manual
Chapter 1
BEFORE USE
4
For labels, fix the paper end with the backing paper stopper, and gently turn the winding
bobbin counterclockwise until the label becomes tight.
5.
Slide the label/receipt guide to help smooth paper feeding according to the paper width.
UNI-7 User’s Manual
1-7
Chapter 1
6.
BEFORE USE
Push the cassette straight into the main body to return to its original position.
yBefore inserting the cassette unit into the main body, ensure that nothing sticks to the
magnet on the bottom of the cassette unit.
yPush the cassette slowly into the main body so as not to get your fingers caught.
7.
For labels, press the [FEED] key on the key sheet to issue a label.
At this time, confirm that the label is completely peeled off.
Confirm that the backing paper is wound up smoothly. If the backing paper is wound up
diagonally, check that the label is set correctly.
1-8
UNI-7 User’s Manual
Chapter 1
BEFORE USE
1.7
REMOVING & REPLACING OF WEIGH PLATTER
1.7.1
REMOVING THE WEIGH PLATTER
When removing the weigh platter from the main body, lift the front side to pull out the two pins from
the two rubber platter holders and remove the platter by pulling it to disengage the two hooks at the
rear side of the platter.
1.7.2
REPLACING THE WEIGH PLATTER
When replacing the weigh platter onto the main body, engage the two hooks at the rear side of the
platter and lower the platter so that the two pins on the bottom of the platter are inserted into holes of
the rubber platter holders.
UNI-7 User’s Manual
1-9
Chapter 1
1.8
1.8.1
1.
BEFORE USE
CLEANING OF THE MACHINE
CLEANING OF THE THEREMAL HEAD
Pull out the cassette from the main body.
Before pulling out the cassette unit, ensure that nothing is placed on the weigh platter.
2.
1-10
Use a cotton-tipped swab to clean off the thermal head.
UNI-7 User’s Manual
Chapter 1
1.8.2
1.
BEFORE USE
CLEANING OF THE LABEL SENSOR
Pull out the cassette from the main body.
Before pulling out the cassette unit, ensure that nothing is placed on the weigh platter.
2.
Use a dry cloth to clean off the emitter and receiver of the label sensor.
UNI-7 User’s Manual
1-11
Chapter 1
1.8.3
1.
BEFORE USE
CLEANING OF THE PRINT ROLLER AND PRISM
Pull out the cassette from the main body.
Before pulling out the cassette unit, ensure that nothing is placed on the weigh platter.
2.
1-12
Use a dry cloth to clean off the print roller and prism.
UNI-7 User’s Manual
Chapter 1
1.8.4
BEFORE USE
PRECAUTIONS WHEN USING CLEANING FLUIDS
Use a soft cloth and a neutral detergent to clean the machine.
Do not use thinner, benzene, etc. Doing so may damage the original safety functions.
For some parts, use cleaning fluid (isopropyl alcohol).
 Do not use cleaning fluid near fire as the fluid is flammable.
 Do not use cleaning fluid in a poorly ventilated area. Always provide adequate
ventilation when cleaning.
Take the following actions in the event of an accident:
If the fluid gets in your eye
 Immediately wash your eye(s) with water for at least 15 minutes, and consult your
doctor.
 If you wear contact lenses, remove and wash them.
If the fluid comes into contact with your skin
 Immediately rinse the area of contact with water, and then wash with soap.
 If you notice any skin abnormalities at the area of contact, or if any pain persists,
consult your doctor.
If the fumes of the fluid are inhaled
 Immediately move the victim to an area where fresh air is available, and have the
victim lie down and keep warm.
 If breathing becomes difficult or stops, provide artificial respiration and seek medical
attention immediately.
If the fluid is swallowed
 Do not try to induce vomiting.
 Do not give the victim anything to drink, and do not rinse the mouth.
 If vomiting occurs naturally, have the victim lean forward to reduce risk of aspiration.
 Keep the victim warm and seek medical attention.
UNI-7 User’s Manual
1-13
Chapter 1
1.9
BEFORE USE
STARTING PROCEDURES
1.9.1 TURNING ON THE POWER
1.
Push down the "I” side of the Power Switch to turn on the power.
2.
The Time Check screen appears.
Then, check that displayed date and time agree with current date and time, and press the
[ENTER] button on the screen to proceed to the next step.
Note: Refer to “Time/Date Set” menu in Adjust Mode when changing the date or time.
21-JUN-2007
11:13:38
3.
1-14
After a while, the initial screen appears.
UNI-7 User’s Manual
Chapter 1
BEFORE USE
1.9.2 PERFORMING ZERO ADJUSTMENT
1.
If the weight value is not zero on the initial screen,
Press the [ZERO] key on the key sheet to perform zero weight adjustment.
2.
The “ZERO” indicator lights up and the weight value becomes zero.
UNI-7 User’s Manual
1-15
Chapter 1
BEFORE USE
1.9.3 GETTING BACK TO THE INITIAL SCREEN
1-16
1.
To get back to the initial screen from a Menu Select screen, press either the “SALES” field
or the icon at the bottom right on the screen.
2.
The initial screen appears.
UNI-7 User’s Manual
Chapter 2
LABEL/RECEIPT ISSUE
LABEL/RECEIPT ISSUE
2.1
2
LABEL ISSUE WITHOUT OPERATOR
2.1.1 WEIGHING UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
3.
4.
or
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
The selected PLU screen appears.
Without Preset Tare Weight
Uni-7 User’s Manual
2-1
Chapter 2
LABEL/RECEIPT ISSUE
With Preset Tare Weight
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
See section 2.4 for Temporary Change Operations.
6.
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
2-2
Uni-7 User’s Manual
Chapter 2
7.
LABEL/RECEIPT ISSUE
When “MANUAL” is set in the Print Mode,
Press the [PRINT] key on the key sheet.
The label is issued.
Non-traceable products
Traceable products
When “AUTO” is set in the Print Mode,
The label is automatically issued as soon as the weighing is stabilized.
Non-traceable products
Uni-7 User’s Manual
Traceable products
2-3
Chapter 2
LABEL/RECEIPT ISSUE
2.1.2 WEIGHING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
3.
4.
or
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
The selected PLU screen appears.
Without Preset Tare Weight
2-4
Uni-7 User’s Manual
Chapter 2
LABEL/RECEIPT ISSUE
With Preset Tare Weight
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
See section 2.4 for Temporary Change Operations.
6.
Put a product on the weigh platter.
The weight is measured but the fixed price stays same.
Uni-7 User’s Manual
2-5
Chapter 2
7.
LABEL/RECEIPT ISSUE
When “MANUAL” is set in the Print Mode,
Press the [PRINT] key on the key sheet.
Non-traceable products
Traceable products
When “AUTO” is set in the Print Mode,
The label is automatically issued as soon as the weighing is stabilized.
Non-traceable products
2-6
Traceable products
Uni-7 User’s Manual
Chapter 2
LABEL/RECEIPT ISSUE
2.1.3 PROCESSING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
4.
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
5.
See section 2.4 for Temporary Change Operations.
The selected PLU screen appears.
Uni-7 User’s Manual
2-7
Chapter 2
6.
LABEL/RECEIPT ISSUE
Press the [PRINT] key on the key sheet to issue the labels.
The label is issued.
Non-traceable products
Traceable products
Remove the label.
The next label is issued.
Non-traceable products
Traceable products
Note: To stop printing, press the [PRINT] key again.
2-8
Uni-7 User’s Manual
Chapter 2
LABEL/RECEIPT ISSUE
2.1.4 PROCESSING FIXED WEIGHT/FIXED UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
4.
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
5.
See section 2.4 for Temporary Change Operations.
The selected PLU screen appears.
Uni-7 User’s Manual
2-9
Chapter 2
6.
LABEL/RECEIPT ISSUE
Enter the fixed weight using the numeric keys on the key sheet and press the “FIXED
WEIGHT” field.
EXAMPLE Fixed weight “858g”
7.
Press the [PRINT] key on the key sheet to issue the labels.
The label is issued.
Non-traceable products
Traceable products
Remove the label.
The next label is issued.
Non-traceable products
Traceable products
Note: To stop printing, press the [PRINT] key again.
2-10
Uni-7 User’s Manual
Chapter 2
2.2
LABEL/RECEIPT ISSUE
LABEL ISSUE WITH OPERATORS
2.2.1 WEIGHING UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
3.
4.
or
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
The selected product screen appears.
Without Preset Tare Weight
With Preset Tare Weight
Uni-7 User’s Manual
2-11
Chapter 2
LABEL/RECEIPT ISSUE
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
6.
See section 2.4 for Temporary Change Operations.
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
2-12
Uni-7 User’s Manual
Chapter 2
7.
LABEL/RECEIPT ISSUE
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
Uni-7 User’s Manual
2-13
Chapter 2
LABEL/RECEIPT ISSUE
2.2.2 WEIGHING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
3.
4.
or
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
The selected product screen appears.
Without Preset Tare Weight
2-14
Uni-7 User’s Manual
Chapter 2
LABEL/RECEIPT ISSUE
With Preset Tare Weight
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
See section 2.4 for Temporary Change Operations.
6.
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
Uni-7 User’s Manual
2-15
Chapter 2
7.
LABEL/RECEIPT ISSUE
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
2-16
Uni-7 User’s Manual
Chapter 2
LABEL/RECEIPT ISSUE
2.2.3 PROCESSING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
4.
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
5.
See section 2.4 for Temporary Change Operations.
The selected PLU screen appears.
Uni-7 User’s Manual
2-17
Chapter 2
6.
LABEL/RECEIPT ISSUE
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
2-18
Uni-7 User’s Manual
Chapter 2
LABEL/RECEIPT ISSUE
2.2.4 PROCESSING FIXED WEIGHT/FIXED UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
4.
When the product is preset as a traceable item, the traceability screen appears.
See section 2.3 for more details about traceability products.
5.
See section 2.4 for Temporary Change Operations.
The selected PLU screen appears.
Uni-7 User’s Manual
2-19
Chapter 2
6.
LABEL/RECEIPT ISSUE
Enter the fixed weight using the numeric keys on the key sheet and press the “FIXED
WEIGHT” field.
EXAMPLE Fixed weight “858g”
7.
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
2-20
Uni-7 User’s Manual
Chapter 2
2.3
LABEL/RECEIPT ISSUE
RECEIPT ISSUE
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
The selected product screen appears.
4.
See section 2.4 for Temporary Change Operations.
Uni-7 User’s Manual
2-21
Chapter 2
5.
LABEL/RECEIPT ISSUE
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
Then, press a operator button on the screen.
EXAMPLE Operator “BETTY”
The subtotal screen for the selected operator appears for a certain time period.
6.
7.
2-22
Repeat steps 2 through 5 for more registrations.
The subtotal screen for the selected operator appears for a certain time period.
To display the detailed subtotal screen for the selected operator, press the subtotal area.
Uni-7 User’s Manual
Chapter 2
8.
The detailed subtotal screen appears.
9.
Press the [PRINT] key on the key sheet.
LABEL/RECEIPT ISSUE
The receipt is issued.
Uni-7 User’s Manual
2-23
Chapter 3
TRACEABILITY PRODUCTS
TRACEABILITY PRODUCTS
3.1
3
REFERING TO PREVIOUS TRACEABILITY DATA
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU number “6”.
Î
3.
or
When the product is preset as a traceable item, the Traceability screen appears.
Uni-7 User’s Manual
3-1
Chapter 3
TRACEABILITY PRODUCTS
4.
To refer to the previously processed traceability data, press the [LIST] button.
5.
The Traceability History screen appears. Then, press to select a desired data field.
6.
The selected data appears. Then, press the [SET] button.
7.
The selected PLU screen appears.
Weighing Unit Price Products
3-2
Uni-7 User’s Manual
Chapter 3
TRACEABILITY PRODUCTS
Fixed Price Products
Fixed Unit Price Products
Weighing Fixed Price Products
Uni-7 User’s Manual
3-3
Chapter 3
3.2
TRACEABILITY PRODUCTS
CHANGING TRACEABILITY DATA
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU number “6”.
Î
3-1
3-4
or
When the product is preset as a traceable item, the Traceability screen appears.
Then, confirm whether information on the screen is correct or not.
When the data is correct, press the [SET] button.
Uni-7 User’s Manual
Chapter 3
3-2
TRACEABILITY PRODUCTS
If the data is not correct, press to select a desired data field.
EXAMPLE Select “France”.
EXAMPLE Change to “Argentina”.
The data has been changed.
To change the “FACTORY” data, press the corresponding field.
Press to select a desired data field.
Uni-7 User’s Manual
3-5
Chapter 3
TRACEABILITY PRODUCTS
The data has been changed. Then, press the [SET] button.
4.
When changing the lot data, press the “LOT” filed.
The Traceability Lot Number Set screen appears.
Change the lot number using the [ABC] [ERASE] and [BACK SPACE] buttons, and press
the [BACK] button to finish.
3-6
Uni-7 User’s Manual
Chapter 3
TRACEABILITY PRODUCTS
The confirmation screen appears. Then, press the [SAVE] button to save the data.
The Traceability screen appears. Then, press the [SET] button.
5.
The selected PLU screen appears.
Weighing Unit Price Products
Fixed Price Products
Uni-7 User’s Manual
3-7
Chapter 3
TRACEABILITY PRODUCTS
Fixed Unit Price Products
Weighing Fixed Price Products
3-8
Uni-7 User’s Manual
Chapter 4
TEMPORARY CHANGE OPERATIONS
TEMPORARY CHANGE OPERATIONS
4.1
1.
4
UNIT PRICE CHANGE
Ensure that the selected PLU screen is displayed.
Weighing Products
Fixed Unit Price Products
2.
Enter a desired unit price using the numeric keys and press the “UNIT PRICE” or “FIXED
UNIT PRICE” field.
EXAMPLE “$3.80”
.
Weighing Products
Uni-7 User’s Manual
4-1
Chapter 4
TEMPORARY CHANGE OPERATIONS
Fixed Unit Price Products
4-2
Uni-7 User’s Manual
Chapter 4
4.2
1.
TEMPORARY CHANGE OPERATIONS
FIXED PRICE CHANGE
Ensure that the selected PLU screen is displayed.
Fixed Price Products
Weighing Fixed Price Products
2.
Enter a desired price using the numeric keys, and press the “FIXED PRICE” field.
EXAMPLE “$3.80”
.
Fixed Price Products
Uni-7 User’s Manual
4-3
Chapter 4
TEMPORARY CHANGE OPERATIONS
Weighing Fixed Price Products
4-4
Uni-7 User’s Manual
Chapter 4
4.3
1.
TEMPORARY CHANGE OPERATIONS
AMOUNT DISCOUNT FOR UNIT PRICE
Ensure that the selected PLU screen is displayed.
Weighing Unit Price Products
Fixed Unit Price Products
2.
Enter a desired discount amount using the numeric keys, and press the “-$ (U/P)” field.
EXAMPLE Discount amount “$1.00”.
Weighing Unit Price Products
Uni-7 User’s Manual
4-5
Chapter 4
TEMPORARY CHANGE OPERATIONS
Fixed Unit Price Products
4-6
Uni-7 User’s Manual
Chapter 4
4.4
1.
TEMPORARY CHANGE OPERATIONS
PERCENT DISCOUNT FOR UNIT PRICE
Ensure that the selected PLU screen is displayed.
Weighing Unit Price Products
Fixed Unit Price Products
2.
Enter a desired discount percentage using the numeric keys on the key sheet, and press
the “-% (U/P)” field.
EXAMPLE Discount percentage “10%”.
Uni-7 User’s Manual
4-7
Chapter 4
TEMPORARY CHANGE OPERATIONS
Fixed Unit Price Products
4-8
Uni-7 User’s Manual
Chapter 4
4.5
1.
TEMPORARY CHANGE OPERATIONS
AMOUNT DISCOUNT FOR TOTAL PRICE
Ensure that the selected PLU screen is displayed.
Fixed Price Products
Weighing Fixed Price Products
2.
Enter a desired discount amount using the numeric keys, and press the “-$” field.
EXAMPLE Discount amount “$1.00”.
Fixed Price Products
Uni-7 User’s Manual
4-9
Chapter 4
TEMPORARY CHANGE OPERATIONS
Weighing Fixed Price Products
4-10
Uni-7 User’s Manual
Chapter 4
4.6
1.
TEMPORARY CHANGE OPERATIONS
PERCENT DISCOUNT FOR TOTAL PRICE
Ensure that the selected PLU screen is displayed.
Fixed Price Products
Weighing Fixed Price Products
2.
Enter a desired discount percentage using the numeric keys on the key sheet, and press
the “-%” field.
EXAMPLE Discount percentage “10%”.
Uni-7 User’s Manual
4-11
Chapter 4
TEMPORARY CHANGE OPERATIONS
Weighing Fixed Price Products
4-12
Uni-7 User’s Manual
Chapter 4
4.7
1.
TEMPORARY CHANGE OPERATIONS
PRODUCT QUANTITY CHANGE
Ensure that the selected PLU screen is displayed.
Fixed Price Products
2.
Enter a desired quantity using the numeric keys, and press the “PCS” field.
EXAMPLE Quantity “2 pieces”
.
3.
To select a desired fix price mark, press the “PCS” field again.
Uni-7 User’s Manual
4-13
Chapter 4
4.
TEMPORARY CHANGE OPERATIONS
The Fix Price mark List screen appears. Then, select a desired mark by pressing the
corresponding field.
EXAMPLE Price mark “PC. PCS.”
4-14
Uni-7 User’s Manual
Chapter 4
4.8
1.
TEMPORARY CHANGE OPERATIONS
PRINT QUANTITY SETTING
Ensure that the selected PLU screen is displayed and “AUTO” is selected in the Printing
Mode.
Fixed Price Products
2.
Enter a desired number of labels and press the “PRN QTY (Print Quantity)” field on the
screen.
EXAMPLE Print quantity “3”.
3.
Press the [PRINT] key on the key sheet.
The set number of labels will be issued.
Note: To interrupt the issue of labels, press the [PRINT] key again.
To continue the issue of labels, press the [PRINT] key again.
Uni-7 User’s Manual
4-15
Chapter 5
SELF-SERVICE OPERATIONS
SELF-SERVICE OPERATIONS
5.1
5
WEIGHING PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Select a desired product by pressing the corresponding button on the screen.
EXAMPLE Select “Roast Beef”
3.
The selected product screen appears.
Uni-7 User’s Manual
5-1
Chapter 5
4.
SELF-SERVICE OPERATIONS
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
5.
Press the [LABEL PRINT] button on the screen to issue the label.
The label is issued.
5-2
Uni-7 User’s Manual
Chapter 5
5.2
SELF-SERVICE OPERATIONS
FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Select a desired product by pressing the corresponding button on the screen.
EXAMPLE Select “Roast Beef”
3.
The selected product screen appears.
Then, press the [LABEL PRINT] button on the screen to issue the label.
The label is issued.
Uni-7 User’s Manual
5-3
Chapter 6
ACCUMULATOR MODE
ACCUMULATOR MODE
6.1
1.
6
MANUAL INPUT ACCUMULATION
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “ACC (Accumulator)” filed.
2.
The Accumulator (Input Number Accumulation) screen appears.
3.
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Input Number Accumulation screen for the selected product appears.
Uni-7 User’s Manual
6-1
Chapter 6
4.
ACCUMULATOR MODE
Enter a quantity, weight, and price that are to be accumulated and press the
corresponding fields for registration. Then, press the [ACC] button on the screen.
EXAMPLE
6-2
Quantity “1 pc.”, Weight “169g”, Price “$0.84”
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
6.
The registration has been completed.
Uni-7 User’s Manual
Chapter 6
6.2
1.
ACCUMULATOR MODE
WEIGHING ACCUMULATION
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “ACC (Accumulator)” filed.
2.
To get the Weighing Accumulation screen, press the [WGT. ACC] tab.
Uni-7 User’s Manual
6-3
Chapter 6
3.
ACCUMULATOR MODE
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Weighing Accumulation screen for the selected product appears.
6-4
4.
Put a product on the weigh platter and press the [ACC] button on the screen..
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
Uni-7 User’s Manual
Chapter 6
6.
ACCUMULATOR MODE
Remove the product from the weigh platter.
Uni-7 User’s Manual
6-5
Chapter 6
6.3
1.
ACCUMULATOR MODE
MANUAL INPUT VOID
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “ACC (Accumulator)” filed.
2.
6-6
To get the Input Number Void screen, press the [NUM. VOID] tab.
Uni-7 User’s Manual
Chapter 6
3.
ACCUMULATOR MODE
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Input Number Void screen for the selected product appears.
4.
Enter a quantity, weight, and price that are to be voided and press the corresponding fields
for registration. Then, press the [VOID] button on the screen.
EXAMPLE
5.
Quantity “1 pc.”, Weight “169g”, Price “$0.84”
The confirmation screen appears. Then, press the [EXEC] button on the screen.
Uni-7 User’s Manual
6-7
Chapter 6
6.
6-8
ACCUMULATOR MODE
The registration has been completed.
Uni-7 User’s Manual
Chapter 6
6.4
1.
ACCUMULATOR MODE
WEIGHING VOID
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “ACC (Accumulator)” filed.
2.
To get the Weighing Void screen, press the [WGT. VOID] tab.
Uni-7 User’s Manual
6-9
Chapter 6
3.
ACCUMULATOR MODE
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Weighing Void screen for the selected product appears.
6-10
4.
Put a product on the weigh platter and press the [VOID] button on the screen..
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
Uni-7 User’s Manual
Chapter 6
6.
ACCUMULATOR MODE
Remove the product from the weigh platter.
Uni-7 User’s Manual
6-11
Chapter 7
TOTAL ADJUST MODE
TOTAL ADJUST MODE
7.1
7
MANUAL INPUT SUBTRACTION
To get the
1.
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “TOTAL ADJUST” filed.
2.
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Total Adjust (Input Number Subtraction) screen for the selected product appears.
Uni-7 User’s Manual
7-1
Chapter 7
3.
TOTAL ADJUST MODE
Enter a quantity, weight, and price that are to be subtracted and press the corresponding
fields for registration. Then, press the [SUB] button on the screen.
EXAMPLE
7-2
Quantity “1 pc.”, Weight “169g”, Price “$0.84”
4.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
5.
The registration has been completed.
Uni-7 User’s Manual
Chapter 7
7.2
1.
TOTAL ADJUST MODE
WEIGHING SUBTRACTION
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “TOTAL ADJUST” filed.
2.
To get the Total Adjust (Weighing Subtraction) screen, press the [WGT. SUB] tab.
Uni-7 User’s Manual
7-3
Chapter 7
3.
TOTAL ADJUST MODE
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Total Adjust (Weighing Subtraction) screen for the selected product appears.
7-4
4.
Put a product on the weigh platter and press the [SUB] button on the screen..
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
Uni-7 User’s Manual
Chapter 7
6.
TOTAL ADJUST MODE
Remove the product from the weigh platter.
Uni-7 User’s Manual
7-5
Chapter 7
7.3
1.
TOTAL ADJUST MODE
MANUAL INPUT ADDITION
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “TOTAL ADJUST” filed.
2.
7-6
To get the Total Adjust (Input Number Addition) screen, press the [NUM. ADD] tab.
Uni-7 User’s Manual
Chapter 7
3.
TOTAL ADJUST MODE
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Total Adjust (Input Number Addition) screen for the selected product appears.
4.
Enter a quantity, weight, and price that are to beaded and press the corresponding fields
for registration. Then, press the [ADD] button on the screen.
EXAMPLE
5.
Quantity “1 pc.”, Weight “169g”, Price “$0.84”
The confirmation screen appears. Then, press the [EXEC] button on the screen.
Uni-7 User’s Manual
7-7
Chapter 7
6.
7-8
TOTAL ADJUST MODE
The registration has been completed.
Uni-7 User’s Manual
Chapter 7
7.4
1.
TOTAL ADJUST MODE
WEIGHING ADDITION
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “TOTAL ADJUST” filed.
2.
To get the Total Adjust (Weighing Add) screen, press the [WGT. ADD] tab.
Uni-7 User’s Manual
7-9
Chapter 7
3.
TOTAL ADJUST MODE
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE
PLU number “6”.
Î
The Total Adjust (Weighing Add) screen for the selected product appears.
7-10
4.
Put a product on the weigh platter and press the [ADD] button on the screen..
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
Uni-7 User’s Manual
Chapter 7
6.
TOTAL ADJUST MODE
Remove the product from the weigh platter.
Uni-7 User’s Manual
7-11
Chapter 8
TOTAL MODE
8.1
TOTAL MODE
8
DAILY TOTAL
1.
Press the “PRODUCTION DAILY TOTAL” filed.
2.
The Daily Total screen appears.
3.
To obtain the Hourly Total screen, press the [HOUR.] tab.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
8-1
Chapter 8
TOTAL MODE
4.
To obtain the Department Total screen, press the [DEPT.] tab.
To change the pages, press the [b] or [a] button on the screen.
5.
To obtain the Group Total screen, press the [GROUP] tab.
To change the pages, press the [b] or [a] button on the screen.
6.
To obtain the Designated Item Total screen, press the [ITEM] tab.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet.
8-2
Uni-7 User’s Manual
Chapter 8
EXAMPLE
TOTAL MODE
PLU number “6”.
Î
7.
To obtain the Operator Total screen, press the [ORER.] tab.
8.
To obtain the Class Total screen, press the [CLASS] tab.
NO
The object of analysis is not specified.
DEPT.
The object of analysis is specified to be departments.
GROUP
The object of analysis is specified to be groups.
PLU No.
Analysis is performed in ascending PLU number order.
ABC PRICE
Analysis is performed in descending price order.
ABC WEIGHT
Analysis is performed in descending weight order.
ABC PCS
Analysis is performed in descending quantity order.
Z PRICE
Analysis is performed in ascending price order.
Z WEIGHT
Analysis is performed in ascending weight order.
Z PCS
Analysis is performed in ascending quantity order.
Uni-7 User’s Manual
8-3
Chapter 8
8.2
8-4
TOTAL MODE
WEEKLY TOTAL
1.
Press the “PRODUCTION WEEKLY TOTAL” filed.
2.
The Weekly Total screen appears.
To change the pages, press the [b] or [a] button on the screen.
3.
To obtain total for the day-of-the week, press a desired day-of-the week tab.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
Chapter 8
Uni-7 User’s Manual
TOTAL MODE
8-5
Chapter 8
8.3
8-6
TOTAL MODE
CUMULATIVE TOTAL
1.
Press the “PRODUCTION CUMULATIVE TOTAL” filed.
2.
The Cumulative Total screen appears.
3.
To obtain total for each department, press the [DEPT.] tab on the screen.
To change the pages, press the [b] or [a] button on the screen.
4.
To obtain total for each group, press the [GROUP] tab on the screen.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
Chapter 8
5.
To obtain total for each operator, press the [OPER.] tab on the screen.
To change the pages, press the [b] or [a] button on the screen.
6.
To obtain analysis totals, press the [CLASS] tab on the screen.
To change the pages, press the [b] or [a] button on the screen.
NO
The object of analysis is not specified.
DEPT.
The object of analysis is specified to be departments.
GROUP
The object of analysis is specified to be groups.
PLU No.
Analysis is performed in ascending PLU number order.
ABC PRICE
Analysis is performed in descending price order.
ABC WEIGHT
Analysis is performed in descending weight order.
ABC PCS
Analysis is performed in descending quantity order.
Z PRICE
Analysis is performed in ascending price order.
Z WEIGHT
Analysis is performed in ascending weight order.
Z PCS
Analysis is performed in ascending quantity order.
Uni-7 User’s Manual
TOTAL MODE
8-7
Chapter 8
8.4
8-8
TOTAL MODE
TRACEABILITY TOTAL
1.
Press the “TRACEABILITY TOTAL” filed.
2.
The Traceability Item screen appears.
To change the pages, press the [b] or [a] button on the screen.
To obtain Traceability Total screen, press the [DETAIL] button on the screen.
3.
The Traceability Total screen appears.
Uni-7 User’s Manual
Chapter 8
8.5
TOTAL MODE
PRESET REPORT PRINTING
1.
Press the “PRESET REPORT” filed.
2.
The Preset Report screen appears.
3.
Select desired reports by pressing the corresponding fields.
Press the [STRAT] button to issue selected join reports.
Uni-7 User’s Manual
8-9
Chapter 8
8.6
8-10
TOTAL MODE
TOTAL CLEAR
1.
Press the [b] button on the screen.
2.
The second page of the Menu Select screen appears.
To obtain the Total Clear screen, press the “TOTAL CLEAR” field on the screen.
3.
The Total Clear screen appears.
4.
Select desired reports to be cleared by pressing the corresponding fields.
Uni-7 User’s Manual
Chapter 8
TOTAL MODE
5.
Press the [EXEC] button.
6.
The confirmation screen appears. Then, press the [EXEC] button on the screen for
execution.
Uni-7 User’s Manual
8-11
Chapter 9 PROGRAM MODE
PROGRAM MODE
9.1
9
PROGRAM MODE ENTRY
1.
Ensure that the initial screen is displayed.
2.
Press the [MODE] key on the key sheet.
The Operation Menu Select screen appears.
Then, press the [PROGRAM] button on the screen.
3.
The Program Menu Select screen appears.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
9-1
Chapter 9 PROGRAM MODE
9-2
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
Note: To exit the Program Mode, press the [ESC] (Escape) key on the key sheet.
Uni-7 User’s Manual
9-3
Chapter 9 PROGRAM MODE
9.2
PLU FILE REGISTRATION
1.
Press the “PLU FILE” field on the Program Menu Select screen.
2.
The Item List screen appears.
To change the pages, press the [b] or [a] button on the screen
3.
Press to select a desired field. Then, press the [DETAIL] button on the screen.
EXAMPLE Select “Roast Beef”.
4.
9-4
The Item Detail screen appears.
To edit the PLU name, press the [EDIT] button on the screen.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
The text edit screen appears.
Edit a text according to the procedure explained in Appendix “Text Editing”.
6.
Ensure that the first sales related screen is displayed.
Sales Mode: Weighing Product
Sales Mode: Fixed Price Product
Sales Mode: Weighing Fixed Price Product
Uni-7 User’s Manual
9-5
Chapter 9 PROGRAM MODE
Sales Mode: Fixed Unit Price Product
ITEM
SALES MODE
MARKDOWN
MODE
OPEN PRICE
UNIT PRICE
FIXED PRICE
M/D AMOUNT
QTY (Quantity)
DESCRIPTION
Press the [<] or [>] button to select a desired sales mode.
0: Weighing product
1: Fixed price product
2: Weighing fixed price product
3: Fixed unit price product
Press the [<] or [>] button to select a desired markdown mode.
0: Normal price
1: Special price
2: Amount discount for total price
3: Percent discount for total price
4: Special unit price
5: Amount discount for unit price
6: Percent discount for unit price
Press the [<] or [>] button to select whether or not to allow an open
price system.
Enter a unit price or fixed price, and press this field.
Enter a markdown amount or percentage and press this field.
Enter a packed quantity, and press this field.
Press this field to display the Fix Price Mark List screen.
UNIT TYPE
TAX
FIXED WEIGHT
TARE
UNDER WEIGHT
UPPER WEIGHT
9-6
Press to select a desired field.
Enter a desired number and press this field.
Enter a fixed weight, and press this field.
Enter a tare weight, and press this field.
Enter a lower weight limit, and press this field.
Enter a upper weight limit, and press this field.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
7.
Press the [SALE2] tab to select the second sales related screen.
ITEM
POINT
FLAG
POINT
TYPE
POINTS
DESCRIPTION
Press the [<] or [>] button to select whether or not to use the Point Flag.
0: OFF
1: ON
Press the [<] or [>] button to select a desired Point Type.
0: Weight
1: Fixed weight
Enter a desired number and press this field
8-1
Press the [MESSAGE] tab to select the message related screen.
8-2
Press to select a desired field.
EXAMPLE “Extra Message 1”.
Uni-7 User’s Manual
9-7
Chapter 9 PROGRAM MODE
8-3
The Extra Message List screen appears. Then, press to select a desired field.
EXAMPLE “Extra Message BB”.
9-1
Press the [IMAGE] tab to select the image related screen.
9-2
Press to select a desired field.
EXAMPLE Select a desired image for “Image 1”.
9-8
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9-3
The Image List screen appears. Then, press to select a desired field and press the [SET]
button.
EXAMPLE Select “Image No.8”.
10.
Select whether or not to print Safe handling Image by pressing a desired field.
11-1
Press the [PRINT] tab to select the print related screen.
11-2
Press the [First Label Format No.] button.
Uni-7 User’s Manual
9-9
Chapter 9 PROGRAM MODE
11-3
The Format List screen appears.
Then, select a desired format by pressing the corresponding field.
EXAMPLE Select “Format No.5”.
ITEM
FIRST LABEL
PRINT
SECOND LABEL
PRINT
DESCRIPTION
Press the [<] or [>] button to select whether or not to print the
first labels.
1: YES
2: NO
Press the [<] or [>] button to select whether or not to print the
second labels.
1: YES
2: NO
Note: The same procedure applies to the Second Label Format Number setting.
9-10
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
12.
Pressing the [DATE] tab to select the date related screen.
ITEM
PACK DATE
PRINT
PACK TIME PRINT
PACK TIME DATA
SB DATE PRINT
SB TIME PRINT
SB TIME DATA
SHELF LIFE
(days)
DESCRIPTION
Select whether or not to print the Pack Date.
Press the [<] or [>] button to select a desired printing method.
0: No print
1: Designated time
2: System clock time
This field is available only when “Designated time” is selected in
“PACK TIME PRINT”.
Enter the time and press this field.
Select whether or not to print the Sell-By Date.
Press the [<] or [>] button to select a desired printing method.
0: No print
1: Designated time
2: Relative time
This field is available only when “Yes” is selected in “SB TIME
PRINT”.
Enter the number of hours and press this field.
This field is available only when “Yes” is selected in “SB DATE
PRINT”.
Enter the number of days and press this field.
UB DATE PRINT
Select whether or not to print the Use-By Date.
UB DATE DATA
This field is available only when “Yes” is selected in “UB DATE
PRINT”.
Enter the number of hours and press this field
Uni-7 User’s Manual
9-11
Chapter 9 PROGRAM MODE
13.
Select the code related screen by pressing the [CODE] tab.
ITEM
ITEM CODE
REGISTER CODE
POS FLAG
BARCODE
POS REFERENCE
DESCRIPTION
Enter an item code and press this field.
Enter the register code and press this field.
This field is available only when “PLU File” is selected in “POS
REFERENCE”. Enter the POS flag number and press this field.
Enter the barcode number and press this field.
Select one of the following reference methods
0: Refer
1: PLU file
This field is available only when “PLU File” is selected in “POS
REFERENCE”.
Press this field to get the Barcode Type screen and press to
select one of the PLU types.
BARCODE TYPE
Press this field to get the Barcode Format screen and press to
select one of the barcode formats.
POS FORMAT
9-12
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
TRACE ENABLE
DEPARTMENT No.
GROUP No.
Uni-7 User’s Manual
Select whether or not to enable a traceability function.
Press this field to get the Department List screen.
Set the desired department simply by pressing the field on the
list, or pressing the “Department No.” field after a numeric
entry.
Pressing this field displays the Group List.
Set the desired group simply by pressing the field on the list, or
pressing the “Group No.” field after a numeric entry.
9-13
Chapter 9 PROGRAM MODE
9.3
CAMPAIGN LIST REGISTRATION
1.
Press the “CAMPAIGN” field on the Program Menu Select screen.
2.
The Campaign List appears.
To change the pages, press the [b] or [a] button on the screen.
3.
Create a new campaign file by entering a campaign number and pressing the [PLU] key
on the key sheet.
EXAMPLE Campaign number “2”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
9-14
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
The designated Campaign Data List screen appears.
5.
Enter the campaign start date and press the “Start Date” display field. .
EXAMPLE Start date "June 25, 2007”
6.
Enter the start time and press the “Start Time” display field. .
EXAMPLE Start time "08:00”
Uni-7 User’s Manual
9-15
Chapter 9 PROGRAM MODE
7.
Enter the campaign end date and press the “End Date” display field. .
EXAMPLE End date "June 27, 2007”
8.
Enter the end time and press the “End Time” display field.
EXAMPLE End time "21:00”
9.
9-16
Press the [CALL] button to call up Item List screens
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
10.
The Item List screen appears. Then, press to select a desired item field.
EXAMPLE PLU number “4”
11.
The Campaign Data List screen appears.
Then, press the [CALL] button again when selecting the next item.
The pop-up list appears. Then, press to select a desired field.
EXAMPLE Percent discount “-%”
Uni-7 User’s Manual
9-17
Chapter 9 PROGRAM MODE
12.
Enter a numeric value and press the “Markdown Price” field for registration.
EXAMPLE 10%
13.
Repeat steps 9 through 12 for further registration.
Then, press the Return button to finalize this procedure.
The Campaign List screen appears.
9-18
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.4
OPERATOR REGISTRATION
1.
Press the "OPERATORS” field on the Program Menu Select screen.
2.
The Operator List screen appears.
3.
To create a new operator, enter the operator number and press the [PLU] key on the key
sheet.
EXAMPLE Operator number “7”.
Î
The confirmation screen appears. Press the [ENTER] button.
Uni-7 User’s Manual
9-19
Chapter 9 PROGRAM MODE
4.
The Operator Edit screen appears for the selected operator number.
Edit a text according to the procedures described in Appendix “Text Editing”.
5.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears.
Then, press the [SAVE] button to save the data.
9-20
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
6.
The edited text has been registered.
7.
Press the Return button to finalize this procedure.
Uni-7 User’s Manual
9-21
Chapter 9 PROGRAM MODE
9.5
9.5.1
9-22
PRESET KEY REGISTRATION
SETTING PRESET FUNCTIONS
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears.
3.
Ensure that the [SET] button is selected.
4.
Press a desired button to which a preset function will be assigned.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
Available functions are listed on the screens.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
9-23
Chapter 9 PROGRAM MODE
6.
Press to select the desired function on the list, and press the [SET] button.
EXAMPLE Select PLU function.
7.
The Item List screen appears. Then, press to select a desired field.
EXAMPLE Select PLU No.2.
9-24
8.
The selected PLU has been assigned.
9.
Repeat steps 4 through 8 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.5.2
ASSIGNING IMAGES ON THE PRESET KEYS
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears.
3.
Press the [IMAGE] button.
4.
Press a desired preset key where the function is already assigned.
EXAMPLE Select “Roast Beef”
Uni-7 User’s Manual
9-25
Chapter 9 PROGRAM MODE
5.
The Image List screen appears.
6.
Press to select a desired image.
EXAMPLE Image No.3
9-26
7.
The image has been assigned.
8.
Repeat steps 4 through 7 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.5.3
COLORING PRESET KEYS
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears.
3.
Press the [COLOR] button. Then, ensure that “Back Color” is selected.
4.
Press to select a desired preset key.
EXAMPLE Select “Roast Beef”
Uni-7 User’s Manual
9-27
Chapter 9 PROGRAM MODE
5.
The Preset Key (Color) screen appears. Then, press to select a desired color.
6.
Selected color has been given to the background of the key.
7.
Press the [BACK COLOR] button to change to the [FORE COLOR] button.
8.
Press to select a desired preset key.
EXAMPLE Select “Roast Beef”
9-28
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.
The Preset Key (Color) screen appears. Then, press to select a desired color.
10.
Selected color has been given to the foreground of the key.
11.
Repeat steps 4 through 10 for more registrations.
Uni-7 User’s Manual
9-29
Chapter 9 PROGRAM MODE
9.5.4
CHANGING PRESET KEY SIZES
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears.
3.
Press the [SIZE] button, and ensure that “SMALL” is selected.
Press the [SMALL] button to change to the [MIDDLE] button.
9-30
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
Press the [MIDDLE] button to change to the [LARGE] button.
4-1
Change the size of a desired key.
EXAMPLE Change to the middle size of the “Roast Beef” key.
Ensure that the [MIDDLE] button is selected.
Press the “Roast Beef” key.
Uni-7 User’s Manual
9-31
Chapter 9 PROGRAM MODE
4-2
Change the size of a desired key.
EXAMPLE Change to the large size of the “Roast Beef” key.
Ensure that the [LARGE] button is selected.
Press the “Roast Beef” key.
5.
9-32
Repeat steps 3 through 4-2 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.5.5
EDITING PRESET KEY NAMES
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears.
3.
Press to select the [EDIT] button.
4.
Press to select a desired preset key.
EXAMPLE Select the [Roast Beef] key.
Uni-7 User’s Manual
9-33
Chapter 9 PROGRAM MODE
5.
The text edit screen appears.
6.
Edit a desired text according to the procedures described in Appendix “Text Editing”.
EXAMPLE “Beef Fillet”.
7.
To finalize the editing, press the [ESC] key on the key sheet.
The confirmation screen appears. Then, press the [SAVE] button to save the data.
9-34
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
8.
The edited text has been registered.
9.
Repeat steps 4 through 8 for more registrations.
Uni-7 User’s Manual
9-35
Chapter 9 PROGRAM MODE
9.5.6
CONFIRMING PRESET KEY DATA
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears.
3.
Press to select the [DATA] button.
4.
Press a desired preset key. The related data is displayed on the button.
EXAMPLE “Beef Fillet” and the PLU No.6
9-36
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.5.7
DELETING PRESET KEYS
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears. Ensure that the [SET] button is selected.
3.
Press a desired preset key to be deleted.
EXAMPLE Delete the [Roast Beef] key”.
4.
The Function List screen appears, and the assigned function field is highlighted.
Uni-7 User’s Manual
9-37
Chapter 9 PROGRAM MODE
9-38
5.
Press to select the “NO” field, and press the [SET] button.
6.
The selected key has been deleted.
7.
Repeat steps 3 through 6 for more deletions.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.5.8
MEMBRANE KEYS
1.
Press the “PRESET KEY” field on the screen.
2.
The Preset Key (Panel) screen appears. Then, press the [MEMBRANE] tab.
3.
The Preset Key (Membrane) screen appears.
4.
Press to select a desired membrane key to which the preset data is assigned.
Uni-7 User’s Manual
9-39
Chapter 9 PROGRAM MODE
The selected key number and name are shown on the screen.
To assign a desired function to the selected key, press the Name field.
5.
The Function List screen appears.
6.
Select a desired function to be assigned by pressing the corresponding field, and press
the [SET] button.
EXAMPLE Select “PLU”
7.
The Item List screen appears. Then, press to select a desired field.
EXAMPLE PLU No.5
9-40
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
8.
The selected PLU has been assigned to the selected membrane key.
Uni-7 User’s Manual
9-41
Chapter 9 PROGRAM MODE
9.6
1.
ADVERTISEMENT MESSAGE REGISTRATION
Press the “AD MSG (Advertisement Message)” field on the Program Menu Select screen.
2-1
The Advertisement Message List screen appears.
When creating the first message, press the [NEW] button.
2-2
When creating a message other than the first one, enter a desired message number using
the numeric keys and press the [PLU] key on the key sheet.
XAMPLE
Message number “2”.
Î
3.
9-42
The confirmation screen appears.
Then, press the [ENTER] button.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
The Advertisement Message (Text) screen appears. Then, press the [EDIT] button.
The Advertisement Message Edit screen appears.
Edit a desired message according to the procedures described in Appendix “Text Editing”.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button to save the data.
Uni-7 User’s Manual
9-43
Chapter 9 PROGRAM MODE
5.
The Advertisement Message (Text) screen for the designated message number appears.
ITEM
TEXT DISPLAY
TYPE
IMAGE DISPLAY
TYPE
TEXT DISPLAY
SPEED
DISPLAY COUNT
9-44
DESCRIPTION
Press the [<] or [>] button to select a desired display type.
0: None
1: Slide
2: Flash
Press the [<] or [>] button to select a desired display type.
0: None
1: Slide
2: Flash
Press the [<] or [>] button to select a desired display speed.
0: Fast
1: Medium
2: Slow
Enter a display count data and press this field.
6.
Press the [IMAGE] tab. Then, the Advertisement Message (Image) screen appears.
7.
When setting an image, press a desired field.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
8.
The Image List appears.
9.
Press to select a desired field and press the [SET] button.
The selected image has been assigned in the designated field.
10.
Repeat steps 7 through 9 for more registrations.
Then, press the Return button to finalize this procedure.
The edited message has been registered.
Uni-7 User’s Manual
9-45
Chapter 9 PROGRAM MODE
9.7
STORE NAME REGISTRATION
9.7.1
CHANGING EXISTING STORE DATA
9-46
1.
Press the “STORE NAME” field on the Program Menu Select screen.
2.
The default store data screen appears.
When changing the store data, press the [EDIT] button.
3.
The Store Name Edit screen appears.
4.
Edit a text according to the procedures described in Appendix “Text Editing”.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
6.
The store name has been changed.
7.
Press to select the address field line and press the [EDIT] button.
8.
The Store Address Edit screen appears.
9.
Edit a text according to the procedures described in Appendix “Text Editing”.
Uni-7 User’s Manual
9-47
Chapter 9 PROGRAM MODE
10.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
11.
9-48
The store address has been changed.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.7.2
CREATING NEW STORE DATA
1.
Press the “STORE NAME” field on the Program Menu Select screen.
2.
The default store data screen appears.
3.
When creating a new store data, enter the desired store number and press the [PLU] key.
EXAMPLE Store number “1”
Î
The confirmation screen appears. Then, press the [ENTER] button.
Uni-7 User’s Manual
9-49
Chapter 9 PROGRAM MODE
4.
The Store Name Edit screen appears for the selected store number.
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
9-50
The store name has been registered
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
8.
Press to select the “Address” field and press the [EDIT] button.
9.
The Store Address Edit screen appears.
10.
Edit a text according to the procedures described in Appendix “Text Editing”.
11.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
Uni-7 User’s Manual
9-51
Chapter 9 PROGRAM MODE
12.
The store address has been registered.
13.
Enter a desired store number as a default store data and press the “Printer 1” or “Printer 2”
display field.
EXAMPLE Set the store number “1” for printer #1.
9-52
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.8
DEPARTMENT NAME REGISTRATION
9.8.1
CREATING NEW DEPARTMENT NAMES
1.
Press the "Department” field on the Program Menu Select screen.
2.
The Department List screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Department Name Edit screen appears.
Uni-7 User’s Manual
9-53
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
When creating more department names, enter a desired department number using the
numeric keys and press the [PLU] key on the key sheet.
EXAMPLE Department number “2”.
Î
9-54
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
The confirmation screen appears. Then, press the [ENTER] button.
9.
The Department Name Edit screen appears.
10.
Edit a text according to the procedures described in Appendix “Text Editing”.
11.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
Uni-7 User’s Manual
9-55
Chapter 9 PROGRAM MODE
12.
The edited text has been registered.
13.
Repeat steps 8 through 12 for more registrations.
9-56
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.8.2
CHANGING EXISITING DEPARTMENT NAMES
1.
Press the "Department” field on the Program Menu Select screen.
2.
The Department List screen appears.
3.
When changing an existing data, press to select a desired field.
4.
The Department Name Edit screen appears for the selected department.
Uni-7 User’s Manual
9-57
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
9-58
7.
The edited text has been registered.
8.
Repeat steps 3 through 7 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.9
GROUP NAME REGISTRATION
9.9.1
CREATING NEW GROUP NAMES
1.
Press the "Group” field on the Program Menu Select screen.
2.
The Group List screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Group Name Edit screen appears.
Uni-7 User’s Manual
9-59
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
When creating more group names, enter a desired group number using the numeric keys
and press the [PLU] key on the key sheet.
EXAMPLE Group number “2”.
Î
9-60
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
The confirmation screen appears. Then, press the [ENTER] button.
9.
10.
The Group Name Edit screen appears.
Repeat steps 5 through 9 for more registrations.
Uni-7 User’s Manual
9-61
Chapter 9 PROGRAM MODE
9.9.2
9-62
CHANGING EXISITING GROUP NAMES
1.
Press the "Group” field on the Program Menu Select screen.
2.
The Group List screen appears.
3.
When changing an existing data, press to select a desired field.
4.
The Group Edit screen appears for the selected group
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
Repeat steps 3 through 7 for more registrations.
Uni-7 User’s Manual
9-63
Chapter 9 PROGRAM MODE
9.10
COOKING INSTRUCTION REGISTRATION
9.10.1 CREATING NEW INSTRUCTIONS
9-64
1.
Press the "Cooking Instruction” field on the Program Menu Select screen.
2.
The Cooking Time List screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Cooking Time Edit screen appears.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
Enter a numeric value for each filed using the numeric keys and press the corresponding
field for registration.
EXAMPLE Base time “35 minutes”
Uni-7 User’s Manual
9-65
Chapter 9 PROGRAM MODE
9.
When creating more instructions, enter a desired cooking instruction number using the
numeric keys and press the [PLU] key on the key sheet.
EXAMPLE Cooking instruction number “2”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
10.
The Cooking Time Edit screen appears.
11.
Repeat steps 5 through 10 for more registrations.
9-66
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.10.2 CHANGING EXISITING INSTRUCTIONS
1.
Press the "Cooking Instruction” field on the Program Menu Select screen.
2.
The Cooking Time List screen appears.
3.
When changing an existing data, press to select a desired field and press the [DETAIL]
button.
4.
The Cooking Time Edit screen appears for the selected instruction
Uni-7 User’s Manual
9-67
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
9-68
7.
The edited text has been registered.
8.
Repeat steps 3 through 7 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.11
NUTRITION FILE REIGISTRATION
9.11.1
CREATING NEW NUTRITION DATA
1.
Press the "Nutrition (USA)” field on the Program Menu Select screen.
2.
The Nutrition List screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Nutrition Data Programming screen for the selected nutrition number appears.
When creating a text for “Serving Size”, press the [EDIT] button.
Uni-7 User’s Manual
9-69
Chapter 9 PROGRAM MODE
5.
The Nutrition Edit screen appears.
6.
Edit a text according to the procedures described in Appendix “Text Editing”.
7.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
8.
9-70
The edited text has been registered. Then, enter a nutrition data for each field using the
numeric keys and press the corresponding field for registration.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.
When creating more nutrition data, enter a desired nutrition number using the numeric
keys and press the [PLU] key on the key sheet.
EXAMPLE Nutrition number “2”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
10.
Repeat steps 4 through 9 for more registrations.
Uni-7 User’s Manual
9-71
Chapter 9 PROGRAM MODE
9.11.2
CHANGING EXISTING NUTRITION DATA
1.
Press the "Nutrition (USA)” field on the Program Menu Select screen.
2.
The Nutrition List screen appears.
3.
Select a desired nutrition number.
EXAMPLE Nutrition number “2”.
or press the [PLU] key on the key sheet after a numeric entry.
Î
9-72
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
Press the [DETAIL] button,
5.
The Nutrition Data Programming screen for the selected nutrition number appears.
When changing a text for “Serving Size”, press the [EDIT] button.
6.
The Nutrition Edit screen appears.
7.
Edit a text according to the procedures described in Appendix “Text Editing”.
Uni-7 User’s Manual
9-73
Chapter 9 PROGRAM MODE
8.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
9.
The edited text has been registered. When necessary, enter a nutrition data for each field
using the numeric keys and press the corresponding field for registration.
10.
Press the Return button after making necessary changes.
11.
Repeat steps 3 through 10 for more registrations.
9-74
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.12
EXTRA MESSAGE REGISTRATION
9.12.1 CREATING NEW MESSAGES
1.
Press the "Extra Message” field on the Program Menu Select screen.
2.
The Extra Message List screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Extra Message Edit screen appears.
Uni-7 User’s Manual
9-75
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
When creating more messages, enter a desired message number using the numeric keys
and press the [PLU] key on the key sheet.
EXAMPLE Message number “2”.
Î
9-76
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
The confirmation screen appears. Then, press the [ENTER] button.
9.
Repeat steps 4 through 8 for more registrations.
Uni-7 User’s Manual
9-77
Chapter 9 PROGRAM MODE
9.12.2 CHANGING EXISITING MESSAGES
1.
Press the "Extra Message” field on the Program Menu Select screen.
2.
The Extra Message List screen appears.
3.
Select a desired message number.
EXAMPLE Message number “2”.
Press a desired field,
or press the [PLU] key on the key sheet after a numeric entry.
Î
9-78
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
Press the [DETAIL] button.
5.
The Extra Message Edit screen appears.
6.
Edit a text according to the procedures described in Appendix “Text Editing”.
7.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
8.
Repeat steps 3 through 7 for more registrations.
Uni-7 User’s Manual
9-79
Chapter 9 PROGRAM MODE
9.13
COUPON MESSAGE REGISTRATION
9.13.1 CREATING NEW MESSAGES
9-80
1.
Press the "Coupon Message” field on the Program Menu Select screen.
2.
The Coupon Message List screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Coupon Message Edit screen appears.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
When creating more messages, enter a desired message number using the numeric keys
and press the [PLU] key on the key sheet.
EXAMPLE Message number “2”.
Î
Uni-7 User’s Manual
9-81
Chapter 9 PROGRAM MODE
The confirmation screen appears. Then, press the [ENTER] button.
9.
9-82
Repeat steps 4 through 8 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.13.2 CHANGING EXISITING MESSAGES
1.
Press the "Extra Message” field on the Program Menu Select screen.
2.
The Coupon Message List screen appears.
3.
Select a desired message number.
EXAMPLE Message number “2”.
Press a desired field,
or press the [PLU] key on the key sheet after a numeric entry.
Î
Uni-7 User’s Manual
9-83
Chapter 9 PROGRAM MODE
4.
Press the [DETAIL] button.
5.
The Coupon Message Edit screen appears.
6.
Edit a text according to the procedures described in Appendix “Text Editing”.
7.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
8.
9-84
Repeat steps 3 through 7 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.14
POP MESSAGE REGISTRATION
1.
Press the "POP Message” field on the Program Menu Select screen.
2.
The message list screen appears.
3.
Enter a desired message number and press the [PLU] key on the key sheet.
EXAMPLE Message number “7”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
Uni-7 User’s Manual
9-85
Chapter 9 PROGRAM MODE
4.
The POP Message Edit screen appears.
Edit a text according to the procedures described in Appendix “Text Editing”.
5.
P Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
9-86
6.
The edited text has been registered.
7.
Repeat steps 3 through 6 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.15
TAX REGISTRATION
1.
Press the "Tax” field on the Program Menu Select screen.
2.
The Tax List screen appears.
3.
When changing a tax system, press to select a desired field.
ITEM
TAX TYPE
TAX RATE
Uni-7 User’s Manual
DESCRIPTION
Press to select one of tax types.
Exclusive tax
Inclusive tax
Tax exemption
Enter a numeric value and press this field.
9-87
Chapter 9 PROGRAM MODE
9.16
SCHEME TABLE REGISTRATION
9.16.1 CREATING NEW TABLES
9-88
1.
Press the "Scheme Table” field on the Program Menu Select screen.
2.
The Scheme Table screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Scheme Table Detail (Basic) screen appears. Then, press the [EDIT] button.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
The Scheme Table Edit screen appears.
6.
Edit a text according to the procedures described in Appendix “Text Editing”.
7.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
8.
The edited text has been registered.
Uni-7 User’s Manual
9-89
Chapter 9 PROGRAM MODE
ITEM
RETAIN LOT No.
LOSS %
DESCRIPTION
Press to select whether or not to use this lot number.
0: No
1: Yes
Enter a numeric value and press this field.
Enter a numeric value and press this field.
Enter a numeric value and press this field.
Press to select whether or not to control the weight limit.
0: No
1: Yes
Press to select whether or not to control the date limit.
0: No
1: Yes
Enter a numeric value and press this field
ITEM
LOT/CARCASS
GTIN
WEIGHT
PASSPORT LOT START
PASSPORT GTIN START
DESCRIPTION
Enter a numeric value and press the corresponding field.
Enter a numeric value and press the corresponding field.
Enter a numeric value and press the corresponding field.
Enter a numeric value and press this field.
Enter a numeric value and press this field.
PASSPORT FORMAT No.
ICON No.
LIFE OFFSET
WEIGHT LIMIT CONTROL
DATE LIMIT CONTROL
9-90
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.
When creating more tables, enter a desired table number using the numeric keys and
press the [PLU] key on the key sheet.
EXAMPLE Table number “2”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
10.
Repeat steps 4 through 9 for more registrations.
Uni-7 User’s Manual
9-91
Chapter 9 PROGRAM MODE
9.16.2 CHANGING EXISITING MESSAGES
1.
Press the "Scheme Table” field on the Program Menu Select screen.
2.
The Scheme Table screen appears.
3.
Select a desired table number by pressing the corresponding field.
EXAMPLE Table number “2”.
or press the [PLU] key on the key sheet after a numeric entry.
Î
9-92
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
Press the [DETAIL] button.
5.
The Scheme Table Detail (Basic) screen appears.
ITEM
RETAIN LOT No.
PASSPORT FORMAT No.
ICON No.
LIFE OFFSET
WEIGHT LIMIT CONTROL
DATE LIMIT CONTROL
LOSS %
Uni-7 User’s Manual
DESCRIPTION
Press to select whether or not to use this lot number.
0: No
1: Yes
Enter a numeric value and press this field.
Enter a numeric value and press this field.
Enter a numeric value and press this field.
Press to select whether or not to control the weight limit.
0: No
1: Yes
Press to select whether or not to control the date limit.
0: No
1: Yes
Enter a numeric value and press this field
9-93
Chapter 9 PROGRAM MODE
ITEM
LOT/CARCASS
GTIN
WEIGHT
PASSPORT LOT START
PASSPORT GTIN START
9-94
DESCRIPTION
Enter a numeric value and press the corresponding field.
Enter a numeric value and press the corresponding field.
Enter a numeric value and press the corresponding field.
Enter a numeric value and press this field.
Enter a numeric value and press this field.
6.
When changing the table name, press the [EDIT] button.
7.
The Scheme Table Edit screen appears.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
8.
Edit a text according to the procedures described in Appendix “Text Editing”.
9.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
10.
The edited text has been registered. Then, press the Return button.
11.
The Scheme Table screen appears.
12.
Repeat steps 3 through 11 for more registrations.
Uni-7 User’s Manual
9-95
Chapter 9 PROGRAM MODE
9.17
1.
Press the "GEN Table” field on the Program Menu Select screen.
2.
The GEN Table screen appears.
3.
Select a desired GEN table by pressing the corresponding field.
4.
9-96
GEN TABLE REGISTRATION
Enter a numeric value and press the corresponding field.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
5.
When changing the title text, press the [EDIT] button.
6.
The GEN Table Edit screen appears.
7.
Edit a text according to the procedures described in Appendix “Text Editing”.
8.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
Uni-7 User’s Manual
9-97
Chapter 9 PROGRAM MODE
9.
10.
9-98
The edited text has been registered.
Repeat steps 3 through 9 for more registrations.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.18
LOOKUP TABLE REGISTRATION
9.18.1 CREATING NEW TABLES
1.
Press the "Lookup Table” field on the Program Menu Select screen.
2.
The Lookup Table screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Lookup Table Data List screen appears. Then, press the [EDIT] button.
Uni-7 User’s Manual
9-99
Chapter 9 PROGRAM MODE
5.
The Lookup Header Table Edit screen appears.
6.
Edit a text according to the procedures described in Appendix “Text Editing”.
7.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
8.
9-100
The edited text has been registered. Then, press the [NEW] button.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.
The confirmation screen appears. Then, press the [ENTER] button.
10.
The Lookup Data Table Edit screen appears.
11.
Edit a text according to the procedures described in Appendix “Text Editing”.
12.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
Uni-7 User’s Manual
9-101
Chapter 9 PROGRAM MODE
13.
The edited text has been registered.
14.
When registering the next data text, enter the data number and press the [PLU] key on
the key sheet.
EXAMPLE Data number “2”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
15.
The Lookup Data Table Edit screen appears.
16.
Edit a text according to the procedures described in Appendix “Text Editing”.
9-102
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
17.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
18.
The edited text has been registered.
19.
20.
Repeat steps 14 through 18 for more data registrations.
21.
The Lookup Table screen appears.
Press the Return button to return to the Lookup Table screen.
Uni-7 User’s Manual
9-103
Chapter 9 PROGRAM MODE
22.
When registering the next header text, enter the header number and press the [PLU] key
on the key sheet.
EXAMPLE Header number “2”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
23.
The Lookup Table Data List screen appears. Then, press the [EDIT] button.
24.
The Lookup Header Table Edit screen appears.
25.
Edit a text according to the procedures described in Appendix “Text Editing”.
9-104
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
26.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
27.
The edited text has been registered. Then, press the Return button.
28.
The Lookup Table screen appears
29.
Repeat steps 22 through 28 for more header registrations.
Uni-7 User’s Manual
9-105
Chapter 9 PROGRAM MODE
9.18.2 CHANGING EXISITING TABLES
1.
Press the "Lookup Table” field on the Program Menu Select screen.
2.
The Lookup Table screen appears.
3.
Select a desired header table by pressing the corresponding field.
EXAMPLE Table number “2”.
or press the [PLU] key on the key sheet after a numeric entry.
Î
9-106
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
Press the [DETAIL] button.
5.
The Lookup Table Data List screen appears.
When changing the header name, press the [EDIT] button
6.
The Lookup Header Table Edit screen appears.
7.
Edit a text according to the procedures described in Appendix “Text Editing”.
Uni-7 User’s Manual
9-107
Chapter 9 PROGRAM MODE
8.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
9.
The edited text has been registered.
10.
When changing the data text, select a desired data text by pressing the corresponding
field. and press the [DETAIL] button.
11.
The Lookup Data Table Edit screen appears.
9-108
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
12.
Edit a text according to the procedures described in Appendix “Text Editing”.
13.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
14.
The edited text has been registered.
15.
16.
Repeat steps 10 through 14 for more data text registrations.
Repeat steps 3 through 15 for more header table text registrations.
Uni-7 User’s Manual
9-109
Chapter 9 PROGRAM MODE
9.19
MINCE TRACEABILITY REGISTRATION
1.
Press the "Mince Traceability” field on the Program Menu Select screen.
2.
The Mince Traceability screen appears.
3.
Enter a numeric value and press the corresponding field for registration.
Then, press the Return button to finalize this procedure.
9-110
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.20
FIXED PRICE MARK REGISTRATION
9.20.1 CREATING NEW PRICE MARKS
1.
Press the "Fixed Mark” field on the Program Menu Select screen.
2.
The Fix Price Mark List screen appears.
3.
Enter a desired mark number using the numeric keys and press the [PLU] key on the key
sheet.
EXAMPLE Mark number “6”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
Uni-7 User’s Manual
9-111
Chapter 9 PROGRAM MODE
4.
The Fix Price Mark Edit screen appears.
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
9-112
The edited text has been registered.
To finalize this procedure, press the Return button.
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.20.2 CHANGING EXISITING PRICE MARKS
1.
Press the "Fixed Mark” field on the Program Menu Select screen.
2.
Select a desired mark number by pressing the corresponding field.
EXAMPLE Mark number “2”.
or press the [PLU] key on the key sheet after a numeric entry.
Î
3.
The Fix Price Mark Edit screen appears.
Uni-7 User’s Manual
9-113
Chapter 9 PROGRAM MODE
4.
Edit a text according to the procedures described in Appendix “Text Editing”.
5.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
6.
The edited text has been registered.
7.
Repeat steps 2 through 6 for more registrations.
9-114
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
9.21
FREE MESSAGE REGISTRATION
9.21.1 CREATING NEW MESSAGES
1.
Press the "Free” field on the Program Menu Select screen.
2.
The Free Message List screen appears. Then, press the [NEW] button.
3.
The confirmation screen appears. Then, press the [ENTER] button.
4.
The Free Message Edit screen appears.
Uni-7 User’s Manual
9-115
Chapter 9 PROGRAM MODE
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
Enter a desired message number using the numeric keys and press the [PLU] key on the
key sheet.
EXAMPLE Message number “2”.
Î
9-116
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
Enter a desired message number using the numeric keys and press the [PLU] key on the
key sheet.
EXAMPLE Message number “2”.
Î
The confirmation screen appears. Then, press the [ENTER] button.
9.
Repeat steps 4 through 8 for more registrations.
Uni-7 User’s Manual
9-117
Chapter 9 PROGRAM MODE
9.21.2 CHANGING EXISITING MESSAGES
1.
Press the "Fixed Mark” field on the Program Menu Select screen.
2.
The Free Message List screen appears.
3.
Select a desired message number by pressing the corresponding field.
EXAMPLE Message number “2”.
or press the [PLU] key on the key sheet after a numeric entry.
Î
9-118
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
The Free Message Edit screen appears.
5.
Edit a text according to the procedures described in Appendix “Text Editing”.
6.
Press the [ESC] key on the key sheet to escape from text editing mode.
The confirmation screen appears. Then, press the [SAVE] button.
7.
The edited text has been registered.
8.
Repeat steps 3 through 7 for more registrations.
Uni-7 User’s Manual
9-119
Chapter 9 PROGRAM MODE
9.22
CHECK LABEL REGISTRATION
1.
Press the "Check Label” field on the Program Menu Select screen.
2.
The Check Label screen appears.
3.
Enter Start Number and End Number using the numeric keys and press the
corresponding fields for registration.
9-120
Uni-7 User’s Manual
Chapter 9 PROGRAM MODE
4.
Press the [STRAT] button to print the labels.
Uni-7 User’s Manual
9-121
Chapter 10
SETUP MODE
10.1
SETUP MODE
10
SETUP MODE ENTRY
1.
Make sure that the initial screen is displayed.
2.
Press the [MODE] key on the key sheet.
The Operation Mode screen appears. Then, press the [SETUP] button on the screen
3.
The Setup Menu Select screen appears.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
10-1
Chapter 10
10-2
SETUP MODE
Uni-7 User’s Manual
Chapter 10
10.2
SETUP MODE
MACHINE NUMBER SETTING
1.
Press the “MACHINE No.” field on the Setup Menu Select screen.
2.
The Machine Number (Basis) screen appears.
3.
Enter a desired numeric value and press the “Dept No.” field.
EXAMPLE Dept number “9”
4.
The confirmation screen appears. Then, press the [EXEC] button to continue.
Uni-7 User’s Manual
10-3
Chapter 10
10.3
SETUP MODE
SALES MODE SETTING
1.
Press the “Sales Mode” field on the Setup Menu Select screen.
2.
The Sales Mode screen appears.
3.
Select a desired mode by pressing the correponding button.
EXAMPLE “Self-service Mode”
10-4
Uni-7 User’s Manual
Chapter 10
10.4
SETUP MODE
PASSWORD SETTING
1.
Press the “Password” field on the Setup Menu Select screen.
2.
The Password (Operate) screen appears.
To change the pages, press the [b] or [a] button on the screen.
3.
Press the [TOTAL] tab to display the Password (Total) screen.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
10-5
Chapter 10
4.
10-6
SETUP MODE
Press the [PROGRAM] tab to display the Password (Program) screen.
To change the pages, press the [b] or [a] button on the screen.
Uni-7 User’s Manual
Chapter 10
Uni-7 User’s Manual
SETUP MODE
10-7
Chapter 10
SETUP MODE
5.
Press the [SETUP] tab to display the Password (Setup) screen.
To change the pages, press the [b] or [a] button on the screen.
6.
Press the [ADJUST] tab to display the Password (Adjust) screen.
7.
Enter a 6-digit password using the numeric keys and press the [PASSWORD] display field
on the screen.
EXAMPLE
10-8
Password “999999”
Uni-7 User’s Manual
Chapter 10
8.
SETUP MODE
Press desired buttons to set whether or not to use the password.
EXAMPLE
Uni-7 User’s Manual
Set to apply the password to “Virtual Receipt” in Total Mode.
10-9
Chapter 10
10.5
SETUP MODE
KEY LOCK SETTING
1.
Press the “Key Lock” field on the Setup Menu Select screen.
2.
The Key Lock (Display Key) screen appears.
3.
Press the [FUNCTION KEY] tab to display the Key Lock (Function Key) screen.
Press the [b] or [a] button to change the pages.
10-10
Uni-7 User’s Manual
Chapter 10
Uni-7 User’s Manual
SETUP MODE
10-11
Chapter 10
10-12
SETUP MODE
Uni-7 User’s Manual
Chapter 10
4
5.
Press the [STROKE KEY] tab to display the Key Lock (Stroke Key) screen.
Enter a 6-digit password using the numeric keys and press the [PASSWORD] display field
on the screen.
EXAMPLE
6.
SETUP MODE
Password “999999”
Press a desired mode by pressing the corresponding tab, and press to select desired
buttons to set whether or not to use the password.
EXAMPLE
Uni-7 User’s Manual
Set to apply the password to “Multi” in Function Key Mode.
10-13
Chapter 10
10.6
SETUP MODE
DATA STORAGE SETTING
1.
Press the “Data Storage” field on the Setup Menu Select screen.
2.
The Data Staorage (Total Add) screen appears.
Press the [b] or [a] button to change the pages.
3.
Press desired buttons to set whether or not to use the total addition.
EXAMPLE
10-14
Set to use the operator total addition.
Uni-7 User’s Manual
Chapter 10
10.7
SETUP MODE
PRESET REPORT SETTING
1.
Press the “Preset Report” field on the Setup Menu Select screen.
2.
The Preset Report (Daily) screen appears.
Press the [b] or [a] button to change the pages.
Uni-7 User’s Manual
10-15
Chapter 10
3.
10-16
SETUP MODE
Press the [WEEKLY] tab to display the Preset Report (Weekly) screen.
Uni-7 User’s Manual
Chapter 10
4.
SETUP MODE
Press the [CUMULATIVE] tab to display the Preset Report (Cumulative) screen..
Press the [b] or [a] button to change the pages.
Uni-7 User’s Manual
10-17
Chapter 10
5.
SETUP MODE
Press a desired mode by pressing the corresponding tab, and press to select desired
buttons to set whether or not to print the totals
EXAMPLE
10-18
Set to print the Production Daily Total (Total).
Uni-7 User’s Manual
Chapter 10
10.8
SETUP MODE
AUTO PROGRAM SETTING
1.
Press the “Auto Program” field on the Setup Menu Select screen.
2.
The Item Auto Overwrite screen appears.
Press the [b] or [a] button to change the pages.
Note: Display items may vary depending on the country setting.
Uni-7 User’s Manual
10-19
Chapter 10
3.
10-20
SETUP MODE
Press to select desired buttons to set whether or not to overwrite the items automatically.
Uni-7 User’s Manual
Chapter 10
10.9
SETUP MODE
DEFAULT DATA SETTING
1.
Press the “Default Data” field on the Setup Menu Select screen.
2.
The Item Initial Data (Sales 1) screen appears.
ITEM
SALES MODE
MARKDOWN
MODE
Uni-7 User’s Manual
DESCRIPTION
Press the [<] or [>] button to select a desired Sales Mode.
0: Weighing product
1: Fixed price product
2: Weighing fixed price product
3: Fixed unit price
Press the [<] or [>] button to select a desired Markdown Mode.
1: Special price
2: Amount discount for total price
3: Percent discount for total price
4: Special unit price
5: Amount discount for unit price
6: Percent discount for unit price
10-21
Chapter 10
SETUP MODE
OPEN PRICE
UNIT PRICE
M/D AMOUNT
QTY
Press the [<] or [>] button to select whether or not to allow open
prices system.
0: Yes
1: No
Enter a unit price and press this field.
Enter a markdown amount or percentage and press this field.
Enter a quantity and press this field.
Press this field to display the Fix Price Mark List screen.
Then, select a desired price mark by pressing the corresponding
field.
EXAMPLE
“Pack Packs”
UNIT TYPE
FIXED PRICE
TAX
FIXED WEIGHT
TARE
UNDER WEIGHT
UPPER WEIGHT
10-22
Enter a fixed price and press this field.
Enter a tax number and press this field.
Enter a fixed weight and press this field.
Enter a tare weight and press this field.
Enter a lower weight limit and press this field.
Enter an upper weight limit and press this field.
Uni-7 User’s Manual
Chapter 10
3.
SETUP MODE
Press the “SALE 2” tab to display the Item Initial Data (Sales 2) screen.
ITEM
POINT
FLAG
POINT
TYPE
POINTS
DESCRIPTION
Press the [<] or [>] button to select whether or not to use a point flag.
0: Off
1: On
Press the [<] or [>] button to select a desired point type.
0: Weight
1: Fixed weight
Enter a point data and press this field.
4-1
Press the “MESSAGE” tab to display the Item Initial Data (Message) screen.
4-2
Press a desired field to display the corresponding list screen.
EXAMPLE
Uni-7 User’s Manual
“Extra Message 1”
10-23
Chapter 10
SETUP MODE
4-3
Select a desired message by pressing the corresponding field.
4-4
The selected message has been registered.
5-1
Press the “IMAGE” tab to display the Item Initial Data (Image) screen.
5-2
Press to select a desired image field.
10-24
Uni-7 User’s Manual
Chapter 10
SETUP MODE
5-3
The Image List screen appears. Then, select a desired image by pressing the
corresponding field.
5-4
The selected image has been registered.
5-5
Press the Display Image field.
5-6
The Display Image List screen appears. Then, select a desired image by pressing the
corresponding field.
Uni-7 User’s Manual
10-25
Chapter 10
SETUP MODE
5-7
The selected image has been registered.
5-8
Select whether or not to print safe handling message.
6.
Press the “PRINT” tab to display the Item Initial Data (Print) screen.
ITEM
FIRST LABEL
FORMAT NO.
SECOND
LABEL
FORMAT NO.
FIRST LABEL
PRINT
SECOND
LABEL PRINT
10-26
DESCRIPTION
Enter a desired format number and press this field.
Enter a desired format number and press this field.
Press the [<] or [>] button to select whether or not to print first labels.
1: Yes
2: No
Press the [<] or [>] button to select whether or not to print first labels.
1: Yes
2: No
Uni-7 User’s Manual
Chapter 10
7.
Press the “DATE” tab to display the Item Initial Data (Date) screen.
ITEM
PACK DATE
PRINT
PACK TIME
PRINT
PACK TIME
DATA
SB DATE PRINT
SB TIME PRINT
SB TIME DATA
SHELF LIFE
(DAYS)
UB DATE PRINT
UB DATE DATA
8.
SETUP MODE
DESCRIPTION
Press to select whether or not to print pack date.
Press the [<] or [>] button to select a desired printing method.
0: No print
1: Designated time
2: System clock time
Enter a desired pack time and press this field.
Press to select whether or not to print sell-by date.
Press the [<] or [>] button to select a desired printing method.
0: No print
1: Designated time
2: Relative time
Enter a number of “Time After” for sell-by time and press this field.
Enter a number of days for shelf life and press this field.
Press to select whether or not to print use-by date.
Enter a number of days for use-by date and press this field.
Press the “DATE” tab to display the Item Initial Data (Date) screen.
ITEM
ITEM CODE
REGI CODE
POS FLAG
BARCODE
POS REFERENCE
Uni-7 User’s Manual
DESCRIPTION
Enter an item code and press this field.
Enter a register code and press this field.
Enter a POS flag number and press this field.
Enter a barcode and press this field.
Press the [<] or [>] button to select a desired reference method.
0: Refer
1: PLU file
10-27
Chapter 10
SETUP MODE
The Barcode Type screen appears when this field is pressed.
Press to select a desired type.
BARCODE TYPE
The Barcode Format screen appears when this field is
pressed. Press to select a desired format.
POS FORMAT
TRACE ENABLE
DEPARTMENT NO.
GROUP NO.
10-28
Press to select whether or not to enable traceability function.
Enter a department number and press this field.
Enter a group number and press this field.
Uni-7 User’s Manual
Chapter 10
SETUP MODE
10.10 PLU UPDATE SETTING
1.
Press the “PLU Update” field on the Setup Menu Select screen.
2.
The PLU Update screen appears.
Press the [b] or [a] button to change the pages.
Note: Display items may vary depending on the country setting.
Uni-7 User’s Manual
10-29
Chapter 10
10-30
SETUP MODE
Uni-7 User’s Manual
Chapter 10
Uni-7 User’s Manual
SETUP MODE
10-31
Chapter 10
SETUP MODE
3.
Enter the start and end numbers and press these fileds to specify the target PLUs.
4.
Select desired items by pressing the corresponding fields.
10-32
Uni-7 User’s Manual
Chapter 10
5.
SETUP MODE
To release the selection, press the selected field again.
To release all the selections, press the [BATCH DELETE] button.
Uni-7 User’s Manual
10-33
Chapter 10
SETUP MODE
6.
Press the [EXECUTE] button to update the selected items.
7.
Press the [EXEC] button for execution.
10-34
Uni-7 User’s Manual
Chapter 10
SETUP MODE
10.11 RECEIPT SETTING
1.
Press the “PLU Update” field on the Setup Menu Select screen.
2.
The Receipt Setting screen appears.
To edit the header and footer titles, press the corresponding field.
3.
The Receipt Title Edit screen appears.
4.
Edit the text according to the procedure explained in Appendix “Text Editing”.
Uni-7 User’s Manual
10-35
Chapter 10
SETUP MODE
5.
The edited text has been registered.
6.
To edit the header and footer logo images, press the corresponding field.
7.
The Image List screen appears.
8.
Select a desired image by pressing the corresponding filed, and press the [SET] button.
10-36
Uni-7 User’s Manual
Chapter 10
9.
SETUP MODE
The edited logo image has been registered.
Uni-7 User’s Manual
10-37
Chapter 11
ADJUSTMENT MODE
11.1
ADJUSTMENT MODE
11
ADJUSTMENT MODE ENTRY
1.
Make sure that the initial screen is displayed.
2.
Press the [MODE] key on the key sheet.
The Operation Mode screen appears. Then, press the [ADJUST] button on the screen
3.
The Adjustment Menu Select screen appears.
Uni-7 User’s Manual
11-1
Chapter 11
11.2
ADJUSTMENT MODE
DATE / TIME ADJUSTMENT
1.
Press the “TIME / DATE SET” field on the Adjustment Menu Select screen.
2.
The Time/Date Set screen appears.
3.
To change the date, enter a new date and press the “DATE” field.
EXAMPLE
11-2
22 June, 2007
Uni-7 User’s Manual
Chapter 11
4.
ADJUSTMENT MODE
To change the time, enter a new time and press the “TIME” field.
EXAMPLE
13:50:00
5.
To register new date and time, press the [SET] button.
6.
The confirmation screen appears. Then, press the [EXEC] button for execution.
Uni-7 User’s Manual
11-3
Chapter 11
11.3
ADJUSTMENT MODE
TOUCH PANEL ADJUSTMENT
1.
Press the “TOUCH PANEL” field on the Adjustment Menu Select screen.
2.
The Touch Panel screen appears.
3.
Press the [+] button on the upper left of the screen.
4.
Press the [+] button on the lower right of the screen.
11-4
Uni-7 User’s Manual
Chapter 11
5.
ADJUSTMENT MODE
Press the [SET] button to confirm calibration.
Uni-7 User’s Manual
11-5
Chapter 11
11.4
ADJUSTMENT MODE
DISPLAY CHECK
1.
Press the “DISPLAY CHECK” field on the Adjustment Menu Select screen.
2.
The Display Check (Vertical) screen appears.
Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer
displays.
3.
Press the [HORIZONTAL] button to change to the horizontal display check screen.
4.
The Display Check (Horizontal) screen appears.
Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer
displays.
11-6
Uni-7 User’s Manual
Appendix
TEXT EDITING
A
TEXT EDITING
A.1
OPERATION PANEL AND KEY FUNCTIONS
„ Operation Panel
„ Text Editing Keys
Used to delete a character by
moving the cursor back by
one character.
Used to select a font size for a
text displayed on the screen.
Used to delete a character at
the place where the cursor is
positioned.
Used to insert a character, or
select characters followed by
depressions of the [→] or [←]
key.
Used to delete a line text.
Used to move the cursor to
right. Also used to select
characters for changing the
style.
Used to specify a normal
character style.
Used to move the cursor to
left. Also used to select
characters for changing the
style.
Used to specify a bold
character style.
Used to select either
lower-case or upper-case
character mode for a text to
be entered.
Uni-7 User’s Manual
A-1
Appendix
A-2
TEXT EDITING
Used to specify an Italic
character style.
Used to copy the original data
to the current data.
Used to specify an
underlined character style.
Used to finalize editing a text.
Used to specify a revered
character.
Used to begin a new character
line.
Used to enter a space at the
place where the cursor is
positioned.
Used to select either a
lower-case or upper-case
mode for a character to be
entered.
Uni-7 User’s Manual
Appendix
A.2
1.
TEXT EDITING
NORMAL CHARACTER EDITING
Confirm that the text edit screen is displayed.
Select a desired character size by using the [Size] key on the key sheet.
The selected size is displayed in the “FONT” display field.
2.
Press the [Lower Case] key on the key sheet to select whether to use upper-case
characters or lower-case characters.
Uni-7 User’s Manual
A-3
Appendix
3.
TEXT EDITING
Enter desired characters using alpha-numeric keys on the key sheet or the screen.
Upper-case characters
Lower-case characters
A-4
Uni-7 User’s Manual
Appendix
4.
TEXT EDITING
To change to a new line, press the [New Line] key on the key sheet.
Enter desired characters.
5.
To finalize the editing, press the [ESC] key on the key sheet.
The confirmation screen appears. Then, press the [SAVE] button to save the data.
Uni-7 User’s Manual
A-5
Appendix
A.3
TEXT EDITING
SPECIAL CHARACTER EDITING
1.
Confirm that the text edit screen is displayed.
2.
To select a desired character style using the following keys.
The selected style is displayed in the “STYLE” display field.
EXAMPLE
Select reversed characters.
3.
A-6
Enter desired characters using alpha-numeric keys on the key sheet or the screen.
Uni-7 User’s Manual
Appendix
4.
TEXT EDITING
Press the [ESC] key on the key sheet.
The confirmation screen appears. Then, press the [SAVE] button to save the data.
Uni-7 User’s Manual
A-7
Appendix
A.4
TEXT EDITING
LINE DELETION
1.
Confirm that the text edit screen for a desired PLU is displayed.
2.
To delete the character line, press the [Line Delete] key on the key sheet.
3.
Press the [ESC] key on the key sheet.
The confirmation screen appears. Then, press the [SAVE] button to save the data.
A-8
Uni-7 User’s Manual
Appendix
A.5
1.
TEXT EDITING
CHARACTER DELETION
To Make a correction for a misspelled word, move the cursor to a place where misspelling
is made by using the [→] or [←] key.
EXAMPLE “GAUDA” → “GOUDA”
or
2.
Press the [Character Delete] key on the key sheet to delete the misspelled character.
Uni-7 User’s Manual
A-9
Appendix
TEXT EDITING
3.
Enter the correct character using the alpha-numeric keys.
4.
Press the [ESC] key on the key sheet.
The confirmation screen appears. Then, press the [SAVE] button to save the data.
A-10
Uni-7 User’s Manual
Appendix
A.6
1.
TEXT EDITING
CHARACTER BACKSPACING
To delete a wrong character that was just entered, press the [Back Space] key on the key
sheet to move the cursor back by one character.
EXAMPLE “E” → “A”
2.
Enter a correct character.
Uni-7 User’s Manual
A-11
Appendix
TEXT EDITING
3.
Complete the text.
4.
Press the [ESC] key on the key sheet.
The confirmation screen appears. Then, press the [SAVE] button to save the data.
A-12
Uni-7 User’s Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement