Noble House 82821 Encino Matte Black Wood Adirondack Chair (2-Pack) Instructions
Advertisement
Advertisement
Caution : You must read this before you proceed
LOVESEAT
Label
A
Picture Description QTY
Backrest Panel 1
Page 1 OF 90
B
C
D
Left Arm Panel
Right Arm Panel
Seat Panel
1
1
1
Label
①
②
③
Before
Beginning
Assembly:
Picture Description
Long Screws
(M7x90mm)
Short Screws
(M7x70mm)
Allen Key
QTY
5
5
1
Page 2 OF 90
Overview
Backrest Panel (A)
Right Arm
Panel (C)
Left Arm
Panel (B)
Seat Panel (D)
FRONT FACING
This Loveseat has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Loveseat parts, the above picture is to help you put the various parts into perspective. Please read through the instructions herebelow to familiarise the parts and steps before assembly.
Page 3 OF 90
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
B
D
Place the Seat Panel (D) with its one side face skywards onto a clean, soft surface to avoid any scratches or damages to the product.
Align the tenon of Seat Panel (D) into the Mortis e of Left Arm
Panel (B) as shown above.
Then, affix the Seat Panel (D) with Left Arm Panel (B) by using
Long Screws ( ① ) and Allen Key ( ③ ).
DO NOT FULLY TIGHTHEN SCREWS.
Page 4 OF 90
Step 3
D
B
Wooden Dowel
A
Then continue position Backrest Panel (A) as shown in picture above.
Align the wooden dowel into the positions in the arms.
Then, affix Left Arm Panel (B) with Backrest Panel (A) by using
Short Screws ( ② ) and Allen Key ( ③ )
DO NOT FULLY TIGHTHEN SCREWS.
Step 4
C
A
D
B
Page 5 OF 90
With the help from your partner, turn the Loveseat to rest on Left
Arm Panel (B) so that Right Arm Panel (C) is now facing skywards.
Repeat the same process by affixing Screws ( ① ), ( ② ) to designated points.
DO NOT FULLY TIGHTHEN SCREWS.
Step 5
Turn the Loveseat right side up.
Place the Loveseat on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit into to the Loveseat.
This would help to align all the parts at all the joint areas.
Then get off the Loveseat, and in a sequential manner, proceed to tighten all screws.
To tighten the Screws at the base of the Backrest, do secure assistance from your adult partner(s).
Page 6 OF 90
assistance from your adult partner(s).
You may be required to turn the Loveseat, to gain easy access to the secure points.
Turn the Loveseat in a synchronised manner.
CAUTION 1: When tightening these screws, tighten sequentially.
DO NOT tighten any screw fully and then towards the next one.
This would cause the frame to warp.
If there is still wobbles, loosen the screws and execute this same process.
WARNING!! IF LOVESEAT IS NOT STABLE , IT COULD LEAD
TO DAMAGING THE PRODUCT.
Ensure all screws are fully locked into position.
The Loveseat is ready to be used.
Caution 2: This Loveseat can only be used on a flat, level surface.
Version two : Oudoor without PE Products
Page 7 OF 90
Page 8 OF 90
Instructions d'Assemblage
Attention : Vous devez lire ce document avant d'assembler
Table avec Rallonge
ATTENTION : Cette table n'est PAS un JOUET.
Garder vos enfants à distance pendant l'assemblage.
Préparation de l'Assemblage
Avant de commencer l'assemblage
9 OF 90
Liste des Pièces
NO.
Image
A
Description
Plateau de Table
B
C
D
Rallonge du Plateau de Table
Panneau Support Pied (Côté Long)
Panneau Support Pied (Côté Court)
E
Pied de Table avec Nivellement Préattaché
Liste des Pièces Détachées
① Boulons (M8*25mm )
②
③
Rondelles ( 8mm )
Rondelles Élastiques ( 8mm )
④ Écrous ( 8mm )
⑤
Étape d'Assemblage
Présentation
Clef
Pieds
(Côté Court)(D)
Panneaux Support
Pieds
(Côté Court)(D)
Panneaux Support Pieds
(Côté Court)(D)
Panneaux Support Pieds
(Côté Court)(D)
Pied de table avec nivellement préattaché(E)
10 OF 90
Cette table a plusieurs pièces et peut prendre jusqu'à environ 30 minutes pour assembler. Pour vous donner une idée générale des pièces de la Table, l'image au dessus vous aide à mettre en perspec les différentes pièces. Veuillez lire les instructions en dessous pour v familiariser avec les pièces et étapes avant d'assembler.
Étape 1
Déballer et placer toutes les pièces sur une surface molle et propre.
Étape 2
Retourner la table vers le bas sur une surface qui ne peut pas égratin le plateau de table.
Attacher les quatre (04) Pieds de Table (E) aux points de jonctions du plateau(A) avec les Boulons( ① ), Rondelles Joint( ③ ) et Rondelles( ② avec le Clef( ⑤ ).
Ne pas encore trop serrer.
Étape 3
11 OF 90
ATTENTION: Pour MAINTENIR les pieds en place, les PANNEAUX SUPPOR
DE CÔTÉ LONG et COURT DOIVENT SE CHEVAUCHER à TOUS LES QUAT
COINS.
Commencer à fixer les Panneaux Support de Côté Long et Court (C&D) aux pieds de table avec les Rondelles ② ), Rondelles Joints( ③ ) et ecrous( ④ ) avec le Clef ⑤
Ne pas encore trop serrer.
Répeter le même processus pour tous les 04 (quatre) points de jonctions des
Pieds et Panneaux Support de Pieds.
Une fois tous les panneaux sont en place, revenir à serrer les boulons fil des pieds comme l'étape 2.
Serrer ses boulons à manière séquentielle.
Faisant cela permet aux pieds de table d'être verrouillés à leur positions.
Ensuite, serrer fermement tous les boulons des Panneaux Support à leu positions.
{ Veuillez noter l'orientation du plateau de table en connectant avec les Panneau
Supports (C&D). }
Étape 4
Placer le Plateau de Table - Rallonge (B) au milieu de la fente.
Ajuster l'angle pour bien intégrer dans l'encastrement du plateau.
12 OF 90
Étape 5
Pousser le plateau vers le centre pour verrouiller dans l'encastrement par rainure et languette dans le rallonge de table (B).
Un interstice de 3mm est attendu après l'assemblage.
Si nécessaire, ajuster les capsules en caoutchouc pré-installées au bout de chaque pied jusqu'à ce que la table est bien équilibrée.
Assurer vous que tous les boulons et écrous sont bien sérrés.
Votre table est maintenant prête à utiliser.
Cette table de café ne peut être utiliser que sur une surface plane et bien
équilibrée.
Version two : Oudoor without PE Products
13 OF 90
14 OF 90
d'assembler
15 OF 90
Pieds
é(E)
QTé
1
1
2
2
4
5
14
14
9
1
16 OF 90
ron 30 e des ettre en perspective
pour vous
⑤
① e et propre.
③
égratiner tions du les( ② )
17 OF 90
② ③ ④
PPORT
LES QUATRE
) aux pieds
le Clef( ⑤ ).
ions des ns filetés
.
t à leur
Panneaux
18 OF 90
par rainure
最后一个部分的维护保养说明,有三个版本 :
Care & Maintenance
版本 1 、所有户内产品。
版本 2 、户外产品(不包含 PE 类产品)
版本 3 、户外产品 , 仅针对 PE 类产品
请根据产品选择对应的版本
bout de
Last parts three Ve
Version one :
Version two : version three : pls choose right ve
et bien
version one
:
Indoor
19 OF 90
20 OF 90
21 OF 90
22 OF 90
23 OF 90
24 OF 90
t parts three Verison Care & Maintenance :
Version one : All indoor products o : Outdoor product ( without PE Products ) on three : Outdoor products for PE Products Only. se right version according to your products
Version three :Oudoor for PE Products
25 OF 90
26 OF 90
27 OF 90
28 OF 90
29 OF 90
30 OF 90
31 OF 90
32 OF 90
Caution : You must read this before you proceed
Adirondack chair
Picture
Label
A
B
C
Picture Description QTY
Backrest 1
Left Arm 1
Right Arm 1
Page 33 OF 90
F
G
H
D
E
Chair Plate 1
Right Front Leg 1
Left Front Leg 1
Junction Plate 1 1
Junction Plate 2 1
Label
①
②
Picture Description QTY
Bolt(M6*40MM) 18
Bolt(M6*80MM) 2
Page 34 OF 90
③ Allen Key 1
Page 35 OF 90
Before
Beginning
Assembly:
Overview
Left Front Leg
Right Arm
Left Arm
Backrest
Junction Plate 1
Right Front Leg Junction Plate 2
This chair has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the chair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Page 36 OF 90
Step 1
Attach Chair Plate(D) and Junction Plate 1(G) to Right Front
Leg(E) and Left Front Leg(F) using Bolt(
①
) with Allen Key(
③) as above picture shows.
.
Step 2
Attach Left Arm(B) and Right Arm(C) to legs using Bolt(
①
) with
Allen Key(
③)
.
Page 37 OF 90
Step 3
Attach Backrest(A) to Arms and Chair Plate(D) using Bolt(
①
) and
Bolt(
②
) with Allen Key(
③
) as above picture shows.
Step 4
Attach Junction Plate 2(H) to Chair Plate(D) using Bolt(
①
) and
Bolt(
②
) with Allen Key(
③)
.
Page 38 OF 90
Page 39 OF 90
WARNING!!
Furniture Tipping Risk.
Serious risk of severe or fatal crush injuries can occur from furniture tipping over if not secured.
Children like to climb on furniture and Unsecured furniture can pose a serious danger.
Please follow all instructions and install the tip-over restraints provided.
In addition to installing the restraints, to help prevent tip-over:
1. Place heaviest items in the lowest drawers,
2. Unless specifically designed to accommodate, do not set TV’s or other heavy objects on top of this product,
3. Never allow children to climb or hang on drawers, doors, or shelves,
4. Do no leave drawers open,
5. Never open more than one drawer at a time, and
6. Do not step on the base.
1 、这个警示用语只适用于需要加装
防倒装置的产品,不需要加装防倒
装置的,
不需要在 AI 中添加这个警示说明。
2 、此警示说明页面放置于 AI 的首页
, 并加注公司名称。
3 、字体大小同 AI 说明书
1, the warning page applies only to need to add the Anti-tipping device products, do not need to apply this page in AI if will not use Anti-tipping device
2, the warning message page placed on the home page of AI, and infuse the name of the company.
3, the font size specification with AI.
纸箱类型Carton type 图片 Pic
短边合页 short side
Carton hinges
1.普通方形纸箱-
纸箱的长和宽都大于40CM。
1.NORMAL CARTON TYPE 1 ---
-For carton both length
&width longer than 40cm.
防割板
Intermedia te cutting board
2.纸箱的长或宽的一边小于40
CM
时,常用于KD餐椅,KD吧椅。
2.For cartons which length or width shorter than 40cm
(usually for carton of kd chair , barstool ).
短边合页 short side Carton hinges
AI 说明书位置 Ai locating place
防割板 intermediate cutting board
3.L型纸箱。
3. L-SHAPE CARTON.
AI 说明
书位置
4.天地盖纸箱.
4.FOR TOP AND EARTH CARTON
AI 说明书位置
KD说明书放置的位置 Ai locating place
说明书用自封袋包好后用透明胶带固定在靠近短边合页那面
的防割板右上角上。
注意:不要放在防割板中间,以免开箱时割坏说明书。
Ai package with valve bag and fixed on the
Intermediate cutting board By Scotch tape where in the right corner of the short side Carton hinges 。
Caution: Could not put AI on the middle of
Intermediate cutting board to prevent cutting AI.
说明书用自封袋包好后用透明胶带固定在靠近短边合页那面
的防割板右上角上。
注意:不要放在防割板中间,以免开箱时割坏说明书。
Ai package with valve bag and fixed on the
Intermediate cutting board By Scotch tape where in the right corner of the short side Carton hinges 。
Caution :Could not put AI on the middle of
Intermediate cutting board to prevent cutting AI.
L型纸箱,说明书用透明胶带固定在图示位置.
For L-SHAPE CARTON, package Ai with valve bag and fixed with Scotch tape as show in picture position .
天地盖纸箱,说明书放置在纸箱里面产品包装物顶部位置
For TOP AND EARTH CARTON,place Ai on the top of package as show in pic .
套装提示页放置位置/ Set Tips locating position
套装提示页放置于AI同一位置。封箱口底部
与顶部各放置一页。
注意:有AI的那边要放置于AI面上,
便于客人开箱即可看见。
Set Tips sheet put the positon same as
AI. Top and bottom need separate one.
Caution: the SET TIPS need to put on the above of AI if there is AI so that customer can notice it after open box.
套装提示页放置于AI同一位置。封箱口底部
与顶部各放置一页。
注意:有AI的那边要放置于AI面上,
便于客人开箱即可看见。
Set Tips sheet put the positon same as
AI. Top and bottom need separate one.
Caution: the SET TIPS need to put on the above of AI if there is AI so that customer can notice it after open box.
套装提示页放置于AI同一位置,放置于AI面上
, 便于客人开箱即可看见。
Set Tips sheet put the positon same as
AI.the SET TIPS need to put on the above of AI so that customer can notice it after open box.
套装提示页放置于AI同一位置,放置于AI面上
, 便于客人开箱即可看见。
Set Tips sheet put the positon same as
AI.the SET TIPS need to put on the above of AI so that customer can notice it after open box.
Description
Line Art
Choice 1
Line Art
Choice 2
Line Art
Choice 3
Line Art
Choice 4
Line Art
Choice 5
Line Art
Choice 6
Line Art
Choice 7
Nut
Nut
Sleeve
Nuts
(M6x18m m)
Nut(6mm) Nut M4 Nut
Crescent
Nut
Nut
Cap
Nut Cap
Rubber
Cap
Cap Cap Nut cap Bolt Cap Nut Cap
Washer
Rings Flat
Washer
Rings
Flat
Washer
Rings
Flat
Washer
Rings
Flat
Washer
Rings
Curved
Washer
Spring
Washer
Rings
Metal Cap &
Gasket
Glass Clip
Cam Lock
Sticker
Cam Bolt &
Cam Lock
Foam Pad
Tube
Tube
Tube
Metal
Tube
Stainles s Steel
Tube
Adjustable
Leveller Adjustab le Glider
Adjustab le
Feet Leveller
Bolt
Bolt(M7*
40mm)
Bolt(M6*
12mm)
Bolt
(M6x45m m)
Bolt
Bolt:
M4X40 mm
Bolt(M10
*15mm)
Eye bolts
Screw Screw
(
M4*50m m )
Screw
Screw
(M5x55m m)
Tapping
Screw
M6
Screw
Screw
(M3.5x14
mm)
Screw
(M4*18M
M)
Wrench
Outside hex wrench
Wrench
M8
Socket
Wrench
Wrench Wrench
Screwdriver
Screwdri ver
Screwdri ver
Screwdri ver
Dual-Use
Screwdri ver
Allen Key
Drawer Rail
Drawer Rail
Left
Drawer
Rail
Right
Drawer
Rail
Left
Drawer
Rail
Right
Drawer
Rail
Drawer
Handle
Drawer
Handle and
Bolts(M4
Shelf
Support
Threaded
Rod
Turning
Plate
Crank
360°Swivel
Mechanism with Foot
Pedal
Cap
Positioning
Dowel
Gliders
Finial
Wheel
Wheel
Wheel
(with brake)
Wheel
(without brake)
Door Knob
Door
Knob connector
Metal Strap (
Mount to
Wall ).
Straight connect or
Trapezoi d connect or
Connect or
Connecti ng piece
Hinge
Magnetic
Door
Stopper
Plastic corner support
Iron Chain
Snap Hook
Corner
Bracket
Metal Strip
Glass Top
Sucker
Line Art
Choice 8
Line Art
Choice 9
Line Art
Choice
10
Embed-
Nut(M5*60)
Hex
Bolt(30m m)
Screw
(M5*60M
M)
Screw (
Wall
Mount )
Screw
With
Plastic
Cap
说明
1、其中A列为中文B列为英文,可以自行筛选安装过程中需要用到的动作描述类别。
2、C列为可以筛选相对应的产品
3、D列为关键词
4、E列为中文的动作描述,F列为英文的动作描述,在A、B、C、D都筛选完成后可以在F列找到对应需要用到的词语
Introductions
1、A column are chinese,B column are English .you can filtrate category according to installation process.
2、C column could filtrate to find corresponding products.
3、 D column are the Key words
4、E column are chinese Action description,B column are English Action description ,after Filter A、B、C、D ,You can find which you want description.
类别 Category
1、其中A列为中文B列为英文,可以自行筛选安装过程中需要用到的动作描述类别。
4、E列为中文的动作描述,F列为英文的动作描述,在A、B、C、D都筛选完成后可以在F列找到对应需要用到的词语
1、A column are chinese,B column are English .you can filtrate category according to installation process.
4、E column are chinese Action description,B column are English Action description ,after Filter A、B、C、D ,You can find which you want description.
Fit Products indoor or outdoor products indoor or outdoor products key words
ASSEMBLE
AVOID DAMAGE
Table chair indoor or outdoor products indoor or outdoor products heavy heavy assistance
assist indoor or outdoor products child indoor or outdoor products slight wobbleness
outdoor products indoor table covers damage
Firepit hot indoor or outdoor products indoor or outdoor products overview loosely tighten
indoor or outdoor products
Canopy Sunshade
Sofa indoor or outdoor products chair chair
Ottoman chair
B ench
Foldable Cabinet
Tabletop
B ED chair seat chair Seat Panel chair Backrest Panel
Cast-table
TV Stand chair-seat and Armrest
TV Cabinet chair-Armrest and Backrest chair-wooden leg chair-backrest and Base
Computer table
Umbrella /Canopy Sunshade
Over tightening windy conditions moving place
Open
Put 、 pull away open 、 Remove 、 Push down
Position..on back 、 Unzip the zipper 、 take out
Position..on back 、 Unzip the zipper 、 take out
Place 、 Open
Place 、 facedown
Attach 、 between the inside facing
Attach 、 using
Attach 、 using
Attach 、 using
Attach 、 using
Attach 、 using
Attach
Inser t…into
Inser t…into
Inser t…into
Inser t…into
Insert…into
Align … onto
Cabinet bed
Align
… to
Align
… on, Insert
Bookcase chair / sofa chair / sofa
Ottoman
Align … to
Install…into
Put…agAInst
Install…into
Bookcase / computer table/ cabinet
Bookcase / computer table/ cabinet
Bed
Cabinet
Ottoman chair chair bench chair
Sofa bookcase chair
Cabinet
All products
All products
All products chair / sofa chair
All products
All products bed cabinet
Ottoman
Sofa chair
Screw…into
Place…onto
Place…under
Turn...upside down.
Position...on
Stand behind
hold up
rightside up
Repeat the same step to
Repeat Step 1 with
Repeat this step with
Ensure… tightly and securely
Tighten …From
Tighten…at
Ensure…are secured
Tighten with
Tighten by turning push…downwards
LOOSELY FASTEN loosely tighten
Peel..off
take…cover
"add or remove" an Acrylic Gasket to achieve evenness
"add or remove" an Acrylic Gasket to achieve evenness
Adjust the Pre-attached Levellers
TV Stand chair chair gradually tighten ready for use
right way up
描述
提示: 组装的这款产品需要 2-3 人
为防止安装过程中损坏产品,该款产品需要放置在一
个柔 软的表面上进行安装
注意:桌子 顶部很重,举起或者移动桌顶时需要 2-
3 个成年人
注意: 这款椅子的部件很大而且十分沉重,移动或者
举起这些部件时需要 2 个成年人互相 协助。
需要你的成人的助理共同 协作完成
注意:建 议你要有一个合作伙伴来帮助你完成整个装
配 过程。
注意: 这款桌子不是玩具 .
安装 过程中请让您的孩子远离 .
提示:塑料 垫片是否需要使用是可以选择的,主要作
用是帮助防止 轻微的晃动,有的脚可能需要不止一片
,有的脚可以不需要。
注意:偶 尔部分 PE 藤条会偏移位置覆盖安装孔位, 请
不要切割 PE 藤不可以,只需要把它从安装空位上移开
就好 .
注意:当打开桌子 时,请不要放太重的物体在桌子边
缘,这样可能会导致桌子滑轨的损坏。
警告 : 火炉在使用 过程直至使用后一段时间都会热量很
高 .
在使用 时和使用后都请不要碰触火炉
当使用的 时候请让你的还在远离 .
使用 过程中请让易燃材料如:木制 &
PE 藤家具等 远离火炉
这款沙发有多个部件,组装可能需要 30 分 钟。请参考
上述 总装图的部件描述 , 该图片是帮助您更清晰的了解
沙 发的各个组成部分。在安装前请阅读下列说明书了
解 组装步骤。
该阶段,螺栓只要松拧
注意:不可 过分拧紧,过分拧紧会导致产品损坏,慢
慢的旋 紧直至安全稳定
注意:没有使用 伞的时候请关闭伞,在强风情况下请
不要使用 伞。
注意:当要移 动沙发时,请和你的助手一起举起沙发
的扶手部分,如果 举起沙发通过沙发前板的话会导致
产品损坏。
开 纸箱,放置干净表面
放置 边上、打开、取出
挪开的防 尘罩边缘;取出
提起打开、取出、下推关上
背面朝上、拉开拉 链、取出
背面朝上、拉开拉 链、取出
放在、打开
放置、面朝下
相 连接、内侧、使用
相 连接、使用
相 连接、使用
相 连接、使用
相 连接、使用
相 连接、使用
相 连接、使用
插入
插入
插入
插入
插入
对齐安装孔位相连
对齐 ..
和 … 的安装孔位相 连
对齐 ..
和 … 的安装孔位相 连
对齐 ..
和 … 的安装孔位相 连
安装 ..
到 …
安装 ..
到 …
安装 ..
到 …
旋入螺 丝到 …
放在 … 上方
放在 … 下方
旋 转 … 倒置
放置 … 成 为 … 方位
支撑住背面
举起
正面朝上
重复相同的步 骤安装 …
重复步 骤 1 来安装 …
重复 这些步骤安装 …
确保 … 锁紧
锁紧 …
锁紧 …
确保 … 锁紧
锁紧 … 用
通 过旋转脚锁紧
往下推 … 锁入
松 拧
松 拧
撕下 …
使 … 覆盖上
增加 … 减少 垫片去调平
增加 … 减少 垫片去调平
调整….
按顺序缓慢的旋紧
可以使用
放置正确的使用位置
Description
NOTE: 2 OR 3 PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS BED.
TO AVOID DAMAGE DURING ASSEMBLY, IT SHOULD BE ASSEMBLED ON A SOFT
SURFACE.
CAUTION: The Tabletop is heavy, always be sure to use two or more adults whenever lifting or moving it.
CAUTION: The chair parts are large and heavy, always have a second adult to assist you when moving and lifting them.
With assistance from your adult partners
NOTE: It is recommended that you have a partner to assist durning the entire assembly process.
CAUTION : This Table is NOT a TOY.
Keep your child / children at bay during the assembly process.
Note: The use of Acrylic Gaskets are OPTIONAL and are especially useful to help alleviate slight wobbleness. Some Legs may need more than one whilst some legs may not need any.
ATTENTION: Occationally some of the PE Wicker shifts and covers the mounting positions preventing easy assembly; the PE Wicker should never be cut, but moved away from the mounting positions.
CAUTION: Please don’t put too much weight on the edges of the table when extending, as you may cause damage to the sliding rAIl.
CAUTION: Firepit will become hot during use and remAIn hot after use.
As the firepit is hot during and after use, Please do not touch it!
KEEP CHILDREN AT BAY DURING USE!!!
Keep away from combustible material and wooden & PE Rattan furniture during use!
This Sofa has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the sofa parts, the above picture is to help you put the various sofa parts into perspective. Please read through the instructions herebelow to familiarise yourself with the parts and steps before assembly.
At this stage, only loosely tighten the Bolts.
Caution: Do not over tighten. Over tightening could lead to damage of the product. Slowly tighten until secure and stable.
Caution: Always close the Canopy Sunshade when not in use and never use the Canopy
Sunshade during strong windy conditions.
Caution: Whenever moving the Sofa, be sure you and your partner lift from the Armrests. Pulling and lifting from the Front Panel can lead to damage of the product.
Open the carton and place all the parts onto a clean, non-marring surface.
Place the chair Base(C) on a clean, non-marring surface.
Lay chair Backrest(A) and inner box aside.
Open the inner box and take out the Four Legs and hardwares.
Put the chair() facedown on a clean, non-marring surface.
Carefully pull away the dust cover from the edge.
Take the legs and hardware bag out of the chair bottom.
(1)Lift up on the top of the Ottoman to open.
(2)Remove the box contAIning Wooden Legs(B) and Acrylic Gaskets(1) from inside the
Ottoman.
(3)Push down on the top of the Ottoman to close.
Position the chair Body() on its back, on a clean, non-marring surface.
Unzip the zipper from the underside of the chair(), take out the Legs() and Washer Rings().
Close the pouch.
Position the Bench on its back, as shown.
Unzip to open and remove the 6 wooden legs. Close the pocket.
Place the Foldable Cabinet(A) on a clean, non-marring surface.
Open the Foldable Cabinet (A) as shown above.
Place the Tabletop() facedown onto a clean, non-marring surface.
attach the Side RAIl(E) between the inside facing of Headboard(B) and Footboard(C) using
Bolt(1), and Washer(2) with Allen Key(3).
Attach the Seat() to the Left Armrest() using Bolts() and Washers() with Allen Key().
Attach the chair Seat Panel() to the Left Legs() using Hardware() with Spanner().
Attach the Backrest Panel() to the Right Legs() using Hardware() with Spanner().
Attach the Central Round Support Ring() to Table Legs() using Hardware() with Spanner().
Attach one of Back Side Panel(8) to the back side of TV Stand using Bolts(B) with Allen Key(A).
Attach the Seat() to the Right Armrest() using Bolts() and Washers() with Allen Key().
Insert Shelf Supports( ) into the lower pre-drilled mounting points in the corners of the left and right sides of left part Cabinet().
Insert the Right Armrest() into the Backrest(), by putting the metal rod on Backrest into the mounting on Right Armrest.
Insert the threaded stem of Wooden Leg() into the threaded hole of chair Base() then tighten by turning the leg clockwise until the leg is completely secure.
Repeat this process with the remAIning three legs.
Insert the small metal arms on the sides of the chair Backrest into the prefabricated slide lock gadget on the chair Base as shown above.
Insert Cam Locks(D) into Cam Lock Position on the Baseboard and turn with Screwdriver(F) until these lock into position.
Align the mounting positions of the Base Pole(D) onto Base Support(A) and attach them with
Washer(C) and Nut(B) using Wrench(I).
Align and fasten Bottom Side Bar(E) to the Left & Right side panels of Foldable Cabinet(A) using
Hardware Pack A.
Align the mounting positions on the outside facing of the Headboard(A) and the Headboard
Foot(B) .
Insert the Headboard Foot(B) into the Headboard(A) using Bolt(10) with Allen Key(9), as shown in above picture.
Align the mountings on Left Lower Side Panel(C) to the mountings on Bookcase Bottom (B).
Attach Left Lower Side Panel (C) to the Bookcase Bottom (B) using Bolt(1) and Washer(2) with
Allen Key(3).
Install the first Wooden Leg() into the bottom of the chair Base() by placing one Washer Ring() onto the threaded stem.
Put the Seat() agAInst the Left Armrest() and line up the three mounting positions of both.
Install the first Leg() into the bottom of the Ottoman by placing one Acrylic Gasket(1) onto the threaded stem.
Insert threaded stem of Leg into one corner of the Ottoman and tighten by turning the leg clockwise.
Screw Cam Bolt() into mounting position on the Bottom Panel() using Screwdriver().
Place the Drawer Bottom Panel( ) onto the Drawer Frame, with one end fitting into the groove of
Drawer Front Panel.
Place the assembled Support Beam(D) under the Bed Frame.
Then, turn Foldable Cabinet (A), upside down.
Position the Ottoman(A) on its back.
Stand behind the chair Base() while holding up the chair Backrest().
With assistance from your adult partner, hold up the fully assembled backrest with Wings, stand behind the chair.
Turn the Bench rightside up.
Repeat the same step to install the remAIning three Legs(D) &(E).
Repeat Step 1 with the remAIning three Legs().
Repeat this step with Upper Right Side Panel().
Ensure all Legs are tightly and securely attached.
Tighten the bolts from inside the Cabinet with Allen key(J).
Tighten all bolts at all joints completely.
Ensure that all Bolts are secured at all joints.
Tighten with Allen Key(J).
Tighten by turning the Leg clockwis, DO NOT OVER TIGHTEN.
Firmly but gently, push the chair Backrest downwards until the Backrest is fully slotted and locked into position.
At this stage, LOOSELY FASTEN these bolts
At this stage, only loosely tighten the Bolts.
Peel Foam Pad(8) off the backing and apply it to the bottom of two Headboard Foot(B) and two
Footboard Foot(D).
Take one Cam Lock Sticker(G) and cover the Cam Lock as shown in the picture.
Place the Ottoman right side up and test for eveness.
If you find the Ottoman is uneven, identify the corresponding leg and "add or remove" an Acrylic
Gasket to achieve evenness.
Position Sofa right side up and test for levelness.
Add or remove Gaskets where needed to achieve levelness.
Adjust the Pre-attached Levellers on the chair Legs until the chair is level with the ground.
DO NOT fully tighten a BOLT in one go and then move on to the next.
Rather, In a sequential manner, gradually tighten each Bolt until all bolts are evenly secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Your chair is ready for use.
Turn the chair right way up, it is now ready for use.
SEQ.
1
Title
AI 线条图先后不一致
AI line drawing are inconsistent
Descri
首 页 AI 需没有体 现产
品正面或者 侧面 45 度
线条图,而且 AI 前后
线条不一致照成客人
困 扰
2
注意审核工厂提供的
线条图是否和实物一
致
Review the whether the line drawing are the same as actual product
工厂提供的线条图和
实物有差距
3 unclear product
产品标识不清 identification
产品细节组装部位没
有特写图,或者特写
图太小,太模糊。
4
5
产品组装效果不同的
Without line drawings of
线条图没有显示 assembling effect
产品前后脚等组装完
成后如果有出 现不同
方向的, AI 说明书没
有明确提醒
工厂提供的 线条图没
有根据我司 现场确认
组装时没有逻辑顺序
,或者组装方位不符
Assembly without logical sequence, or assembly
合实际 actual.
的 顺序进行,工厂自
行更改安装
成
装
AI 不符合
顺序,造
实际的组
顺序和方位,客人
在 组装时增加难度或
者存在安全 隐患。
6
7
8
工厂提供的线条图打
AI 线条图颜色太浅, line drawing color unclear
或者出 现多种颜色 or more than one color.
印出来后模糊不清,
或者提供线条图有多
种颜色。
AI 文字描述不 规范
AI text description nonstandard
如: 1 、组装步骤中
不能再使用 HOLES 这
个单词
2 、组装时如果不是
一步拧紧,则用 LOOS
ELY
TIGHTEN ,不再使用 D
O NOT OVERTIGHTEN
AI 格式不 规范
AI format is not standardized
每句话结束没有另起
一行
9 AI 忽略了 测平 Forget test Level
需要 测平的产品在 AI
中没有体 现如何测平
10
一幅图有多个线条图
一副图片涉及到多个
线条图组合时,没有
Line graph did not be combined when one
组合而成的, ISP 没有
用组合工具把线条图
把线条图组合起来 line graphs.
片一拖动就容易出现
部分线条图位移。
11 AI 配件数量 错误 errors in quantity of AI accessories
MP=2 的 产品, AI 中体
现双数
12 part list 中部件的位置不正 incorrect direction of parts in part list
确
Partlist 中部件没有根
据实际产品组装后的
位置来显示 。
13
AI 组装步骤中体现包
装物 wrappage showed in AI steps
AI 容易在第一步取出
产品时体现珍珠棉等
包装物
14
组装步骤中没有体现
需要几个人 组装该产
品 no remind customer how many people need in this assembly this steps
AI 步骤中容易遗漏需
要多少人组装这个产
品的提示语
Frequently Asked Questions and Answers.
cription
Home page of AI does not reflect line drawings of front or flank 45 angle of products, and customers will be confused when AI front line and later line are inconsistent.
Guided Operation Steps
注意 审核 AI 是否是需
要 产品正面或者侧面
45 度 ,
线条图。而且整份说
明 书的线条图,线型
从 头到尾要保持一致 .
并且 图片上不需要体
现产品尺寸等信息。
Please pay attention to review whether the AI need line drawing of products in 45 angle. And full specification of AI line graph and linear need to remAIn consistent from beginning to the end.
The line drawing provided by factory are different from actual products.
Pls check if the line
可以通过导出 SAMPLE drawing and actual item
REPORT 、和实物核
对等方式查看线条图 are in an inconsistent state according to object review.
The assembled parts of products detAIls are without close-up views,or close-up photos are too small to view.
产品细节组装部位需
体现特写图,并且特
写图要大。一个动作
The assembled parts of products detAIls should present large and clear close-up view. One step.
There is no clear warning on AI when front and back legs assembled in
部件较多的复杂产品
,或者有方向性的产
品,需要提醒客人对
各个部件进行贴序号 different directions
For complex products with many parts or directed products,please remind guests to serial number labels on the
Factory provides the line drawing without according to confirmed steps by our company.
Factory changes the installation order by themselves and cause impractical assembly
ISP need to supervise
ISP 督促工厂一定要根
据我司 QE 现场确认的 the factory according to
AI assembly steps and
AI 组装步骤和方位进
行,避免照成工厂的 position confirmed by QE confirmation on site to
重复工作和 节省 AI 确 avoid repeated work of
认时间。 factory and save time on
AI confirmation.
Line drawing provided by the factory is blurry after printed, or line drawing has a variety of colors.
说明书线条图颜色需
提醒工厂注意加粗加
黑,保证印刷出来后
清晰。线条图和字体
Pls also make sure there is to be NO MORE than
BLACK colour shown in all AIs coming to me. All
颜色统一用黑色。 in BLACK prints.
Such as: 1. the assembly
2.If the assembly don't
TIGHTEN in one step, then use LOOSELY
TIGHTEN, no longer use the DO NOT
1 、组装步骤中不能 steps no longer use the 再使用 HOLES 这个单 word HOLES. 词,改为 MOUNTING
POSITIONS.
2 、 For all Screws and or Bolts
USING
–
“
Pls STOP
DO NOT
OVERTIGHTEN ” rather
1 、 Pls stop use“ holes ”
, use “MOUNTING
POSITIONS“ instead .
2 、 For all Screws and or Bolts – Pls STOP
USING “DO NOT
OVERTIGHTEN” rather use “LOOSELY
Did not start next line when one sentence is finished.
每一句话结束后要重
新起一行
‘Every sentence to start on a NEW Line. All
Hardware and Parts must use LARGE CAPITAL for the first letter eg.,
AI did not show how to test Level of product which is required.
需要检查产品是否要
测平
Need to check whether the stationarity of product test is necessary.
ISP did not combine line graphs when one picture involves several line graphs, so the line graphs will be displaced when the picture is dragged.
一副图片涉及到多个
线条图时,需要把所
有线条图都组合起来
Line graphs must be combined when one picture involves several line graphs.
AI shows double accessories for products of MP=2.
针对 MP=2 的产品,制
作说明书时只要制作
一份的数量就好,纸
箱内也只要放入一份
For products of MP=2, just shows only one set of AI accessories, and only one AI on the
The display of components is different from the actual assembled one.
Part list
中产品的放置方位要
根据产品组装完成后
的位置来显示。
The orientation of products in part list should be in perfect accordance with actual assembled products.
In the first step of AI when taking products out, it's easy to show the packing materials such as EPE.
说明书不需要体现包
装物
It's unnecessary to show the wrappage in AI.
the remind for how many people need invloved in this steps are frequently missing in AI description.
有的步骤需要两个人
组装,有的步骤需要
3 个人组装,在文字
描述中都要明确提出
。
some stage 2 adult person is needed.
At some stage 3 adults are needed , the AI description need remind this
L
L
× √
screwed into the middle holes. screwed into the middle mounting positions
Place the Ottoman right side up and test for eveness.if you find the Ottoman is uneven, identify the corresponding leg and "add or remove" an Acrylic Gasket to achieve evenness.your Ottoman it is ready for use.
Place the Ottoman right side up and test for eveness.
If you find the Ottoman is uneven, identify the corresponding leg and "add or remove" an Acrylic
Gasket to achieve evenness.
Your Ottoman it is ready for use.
Use of Acrylic
Gasket to alleviate wobbleness and to achieve evenness.
Use of Acrylic
Gasket to alleviate wobbleness and to achieve evenness.
With assistance from your adult partners
From :
To :
Ms ____
Manager – SBU
Noble House / PermAIsuri Co Ltd
Fuzhou, Fujian
China
MS/Mrs
Date :____/ ___ / __
Dear ____
FINAL NOTIFICATION : Factory need to provide AI on time to avoid delay the shipment date
We at Noble House / PermAIsuri Co Ltd, hereby duly informs _____________________ to provise time and AI must fulfill the requirements of permAIsuri .
_________________________________ could not provide AI on time lead to delay the shipment date
,This penalty charge is in the monetary value of U$1,000.00 ( ONE THOUSAND DOLLARS ) per contAIn delay up to a period of 7 days. Further delay beyond 07 days will incur even higher penalty charges
. __________________ shall be held fully responsibility. The incidents that may occur are due to
1 )The sample have been confirmed by permAIsuri ,but ____________________ could not provid assembly instructions within 5 working days after the signature of contract , that result in delay the shipment date .
2 )_____________________ provide the AI draft whithin 5 working days , but the AI could not mee requirements of the permAIsuri, ______________________ revised AI result in delay the shipmen date .
please acknowledge by signing this letter and returning to our office.
Yours sincerely, __________________ , acknowledges the above for PO# ____________________
Ms__
Encl.,
FILE : Version 1 / 2015
MS/MR Date :__
, rovise AI on ent date tAIner per arges e to : rovide y the ot meet shipment
__________
PART # PART DESCRIPTION
HM #
60377
60377
(as shown on AI)
Part A
(as shown on AI)
Top Panel
Part B Left Side Panel
60377 Part C Right Side Panel
60377 Part D Long Center Panel
60377 Part E
Left Short Center
Panel
60377 Part F
Right Short Center
Panel
60377 Part G Left Middle Panel
60377 Part H Right Middle Panel
60377 Part I Door Panel
60377 Part J Back Panel
60377 Part K Bottom Panel
60377 Part L Knob Handle
60377 Part M Metal Leg
60377
60377
60377
60377
60377
60377
60377
60377
60377
60377
Hardware Pack Hardware Pack
Haredware 1 Cam Lock
Haredware 2 Cam Bolt
Haredware 3 Cam Cap
Positioning
Haredware 4 Dowel(8*30mm)
Haredware 6 Screw(3.5*16mm)
Haredware 7 Screw(4*32mm)
Haredware 8 Nail
Haredware 9 Allen Key
Haredware 10 Connector
QUAN
TITY
(as show n on
AI)
1
1
1
1
1
1
1
1
1
1
1
2
5
1
15
15
15
25
24
3
31
1
2
MP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TOT
AL
QU
AN
TIT
Y
1
1
1
1
1
1
1
1
1
1
1
2
5
1
15
15
15
25
24
3
31
1
2
COMME
NTS
60377 Haredware 11 Screwdriver
60377 Haredware 12 Hammer
0 1 0 not provided
0 1 0 not provided
HMNUM+PART
60377.00Part A
60377.00Part B
60377.00Part C
60377.00Part D
60377.00Part E
60377.00Part F
60377.00Part G
60377.00Part H
60377.00Part I
60377.00Part J
60377.00Part K
60377.00Part L
60377.00Part M
60377.00Hardware Pack
60377.00Haredware 1
60377.00Haredware 2
60377.00Haredware 3
60377.00Haredware 4
60377.00Haredware 6
60377.00Haredware 7
60377.00Haredware 8
60377.00Haredware 9
60377.00Haredware 10
60377.00Haredware 11
60377.00Haredware 12
COUNT
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1. 本页为 Part catalog report格式。以60377产品AI
作为样板参考。
2、A列中,当产品为单件时,后缀.
00可以省去,直接填为主码,如:
60377;当产品为套件时,
后缀的.00位置填写英文代码。
如:61288-L,61288-R, 61288-
T等。
B/C/D列按照AI的信息输入。
E列:MP按照每箱实际装入的数量填
写。
F列为每箱包装中各个部件的实际总
数量。依据公式自动计算,
不用手填写。
3、五金配件中显示需要但我司未提
供的,在D列中显示数字为零,这样
明白在F列总配件数量中显示为“0
”。“ not provided"说明标注在G列。
4、所有英文首写为大写,
并保证格式统一对齐。不得首写字
母为小写,每行格式错位等。
5、"H+I"列为公式列,
用于核查重复输入AI的情况。
当“I”列显示为数字“1”时,
表示此为首次输入;当数字显示为
“2”时,表示有重复输入的情况,
需要检查后确认保留正确的数据。
这两行不需要输入,是根据输入数
据自动生成。
1
comments
1. this is Part Catalog Report template.filling 60377 as sample to refer.
2. Column A, fill item code without suffix when item is single product, e.g 60377. but need to add suffix while fill set product. E.g
61288-L, 61288-R, 61288-T, etc.
Column B/C/D fill according to AI data.
Column E,MP fill figure according to shipped
QTY each carton.
Column F, should be the total QTY in the carton. it's created by fomular, no need to put into by hand.
3. Hardware shows be necessary but not provided by our company should fill figure"ZERO"in the column D, thus there is zore in column F. Comments "not provided" must put into column G instead of in column C.
4. All the first written in English to uppercase, and ensure the format unification alignment.Can not write a letter to lowercase, dislocation row format, etc
5. Column "H + I" is a formula for repeated input AI inspection.When "I" column shows for the number "1", says this is a first input;When the digital display is "2", says it has repeated input, need to check after confirm reserves the right data.These two columns do not need to input, it is automatically generated based on the input data.

Public link updated
The public link to your chat has been updated.
Advertisement