Facial & Fingerprint Recognition Product Series User Manual V1.1.8

Facial & Fingerprint Recognition Product Series User Manual V1.1.8
National World Systems
Facial & Fingerprint Recognition Product
Series User Manual
Version: 1.1.8
Date: November 2010
About This Manual
This document introduces the user interface and menu operations of the Facial &
Fingerprint Recognition (FFR) terminal series. For the installation of the FFR
terminal, see Facial & Fingerprint Recognition Product Series Installation Manual.
National World Systems. www.nwstm-us.com
Important Claim
Firstly thank you for purchasing this face and fingerprint hybrid terminal, before
use, please read this manual carefully to avoid the unnecessary damage! The
company reminds you that the proper user will improve the use affect and
authentication speed.
No written consent by ZKSoftware Inc., any unit or individual isn’t allowed to
excerpt, copy the content of this manual in part or in full, also spread in any form.
The product described in the manual maybe includes the software which
copyrights are shared by the licensors including ZKSoftware Inc. Except for the
permission of the relevant holder, any person can’t copy, distribute, revise, modify,
extract, decompile, disassemble, decrypt, reverse engineering, leasing, transfer,
sub-license the software, other acts of copyright infringement, but the limitations
applied to the law is excluded.
Due to the constant renewal of products, the company can
not undertake the actual product in consistence with the
information in the document, also any dispute caused by the
difference between the actual technical parameters and the
information in this document. Please forgive any change
without notice.
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Content
1 Instruction for Use........................................................................................ 1
1.1 Finger Placement.................................................................................. 2
1.2 Use of Touch Screen ............................................................................ 3
1.3 Touch Operations ................................................................................. 4
1.4 Appearance of the FFR Terminal ......................................................... 5
1.5 Main Interface ...................................................................................... 6
1.8 Verification Modes ............................................................................... 8
1.8.1 Fingerprint Verification .......................................................... 8
1.8.2 Facial Verification ................................................................ 10
1.8.3 Password Verification.......................................................... 12
1.8.4 ID Card Verification ............................................................. 13
2. Main Menu ................................................................................................. 15
3. User Management .................................................................................... 18
3.1. Adding a User.................................................................................... 19
3.1.1 Entering a User ID............................................................... 20
3.1.2 Entering a Name.................................................................. 21
3.1.3 Enrolling a Fingerprint......................................................... 22
3.1.4 Enrolling a Password .......................................................... 23
3.1.5 Enrolling a Face................................................................... 24
3.1.6 Entering a Group No. .......................................................... 25
3.1.7 Enrolling an ID Card * ......................................................... 26
3.1.8 Modify User Rights .............................................................. 27
3.1.9 Enroll Photos........................................................................ 28
3.2 Edit a User.......................................................................................... 29
3.3 Delete a User...................................................................................... 30
3.4 Query a User ...................................................................................... 31
3.4.1 Query by User ID................................................................. 31
3.4.2 Query by Name.................................................................... 32
-1-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
4. Communication-related Settings ............................................................ 33
4.1 Network Settings................................................................................ 33
4.2 Serial Port Settings............................................................................. 34
4.3 Wiegand Output ................................................................................. 35
4.3.1 Wiegand 26-bits Output Description................................. 35
4.3.2 Wiegand 34-bits Output Description................................. 37
4.3.3 Customized Format............................................................. 38
5. System Configuration............................................................................... 43
5.1 Basic Parameters ................................................................................ 43
5.2 Interface Parameters........................................................................... 44
5.3 Fingerprint Parameters ....................................................................... 45
5.4 Face Parameters ................................................................................. 46
5.5 Log Settings ....................................................................................... 48
5.6 Update ................................................................................................ 49
6. Data Management .................................................................................... 50
6.1 Query a Record .................................................................................. 51
6.2 Work Code ......................................................................................... 52
7. USB Disk Management ........................................................................... 54
8. Keyboard Definitions ................................................................................ 55
9 Auto Test...................................................................................................... 57
10 Screen Calibration ................................................................................... 59
11 Bell Setting ............................................................................................... 60
12 Access Control Setting............................................................................ 62
13 Date/Time Setting.................................................................................... 63
13.1 Set Date/Time .................................................................................. 63
13.2 Set Daylight Saving Time (DST) ..................................................... 64
14 System Information ................................................................................. 66
14.1 Records ............................................................................................ 66
14.2 Terminal........................................................................................... 66
-2-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Appendix......................................................................................................... 67
Appendix 1 Text Input Instructions.......................................................... 67
Appendix 2 Rules for Uploading Promotional Pictures........................... 69
Appendix 3 Introduction to Wiegand....................................................... 70
Appendix 4 Photo ID Function ................................................................ 71
Appendix 5 Attendance Status Selection Function .................................. 73
Appendix 6 Statement on Human Rights and Privacy ............................. 74
Appendix 7 Environment-Friendly Use Description ............................... 76
-3-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1 Instruction for Use
1.1 The Distance,Facial Expression and Stand Pose
1)The recommended distance:
The recommended distance between person and
device is 0.5m (applied to height range
1.5~1.85m). According to the obtained face image
from device to adjust, when the face image is
comparatively bright, please move backwards
appropriately; when the face image is
comparatively dark, please move forwards
appropriately.
2)The recommended facial expression and several poor-effect facial
expressions:
3 )The recommded stand pose and several poor-effect stand poses:
Note: During the enrollment and verification, please remain the normal
facial expression and stand pose.
-1-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.2 Enrollment Pose
During the enrollment, display the face in the centre of screen as possible. According
to the device’s voice prompts, do some small-scope head actions such as turn left,
turn right, rise, bow and so on to ensure that the different parts of face are inputted
into system to improve the verification accuration. The enrollment poses are as
follows:
Look ahead
(rise)
Focus on
the screen
Focus on
the camera
(bow)
Turn left
slightly
Turn right
slightly
-1-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.3 Finger Placement
Recommended fingers: The index finger, middle finger or the ring finger; the thumb
and little finger are not recommended (because they are usually clumsy on the
fingerprint collection screen).
1)
Proper finger placement:
The finger is flat to the surface
and centered in fingered guide.
2)
Improper finger placement:
Not flat to the surface
Off-center
Off-center
Slanting
Please enroll and verify your fingerprint by using the proper finger placement
mode. We shall not be held accountable for any consequences arising out of
the degradation in verification performance due to improper user operations.
We shall reserve the right of final interpretation and revision of this document.
-2-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.4 Use of Touch Screen
Touch the screen with one of your fingertips or the top of the forward edge of a
fingernail, as shown in the following figure. A broad point of contact may lead to
inaccurate pointing.
When the touch screen is less sensitive to the touch, you can perform screen
calibration through menu operations. Press [Menu] → [Calibration] on the screen
and a cross icon will be displayed. After you touch the center of the cross at five
locations on the screen correctly, the system automatically returns to the main menu.
Press [Return] to return to the initial interface. For details, see 10 Screen Calibration
in this manual.
Smear or dust on the touch screen may affect the performance of the touch screen.
Therefore, try to keep the screen clean and dust-free.
-3-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.5 Touch Operations
1)
Enter numbers. Press the [User ID] key. The system automatically displays the
number input interface. After entering the user ID, press [OK] to save and
return to the previous interface.
2)
Enter Text. Press the [Name] key. The system automatically displays the text
input interface. After entering the user name, press [X] to save and return to the
previous interface.
3)
Modify parameters. Press the default value of a parameter and the system
automatically switches to another value of this parameter.
-4-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.6 Appearance of the FFR Terminal
Indicator
Touch screen
Push buttons
Fingerprint
collection area
ID card
area
swipe
Camera
-5-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.7 Main Interface
① Menu
② Time
③ Date
④ 1:1 or 1:G Function Key
⑤ Facial/Fingerprint Switch Key
⑥ Current Group No.
⑦ Facial/Fingerprint Image
⑧ Attendance Status
⑨
F1
F2
F3
F4
F5
F6
Screen
Shortcut
⑩ Keyboard Shortcut Keys
①Menu: You can enter the main menu by touching this key.
②Time: Current time is displayed. Both the 12-hour and 24-hour time systems are
supported.
③Date: Current date is displayed.
④1:1 or 1:G Function Key: You can enter the digital input interface of 1:1 or 1:G
verification mode. You can set the “1:1/1:G” shortcut key through ⑨ Screen Shortcut
Keys. This key is automatically hidden if the [Toolbar Style] is set to “Permanent
Display”.
⑤Facial/Fingerprint Switch Key: By pressing this key, you can switch between the
facial and fingerprint recognition modes. You can set the “Facial/Fingerprint Switch
Key” shortcut key through ⑨ Screen Shortcut Keys. This key is automatically hidden
if the [Toolbar Style] is set to “Permanent Display”.
-6-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
⑥Current Group No.: When the terminal is currently in the facial recognition mode,
users in current group can perform facial comparison directly, while users of another
group need to enter the group No. before performing the facial comparison.
⑦Facial/Fingerprint Image: If a facial image is displayed, the terminal is currently
in the facial recognition mode; if a fingerprint image is displayed, the terminal is
currently in the fingerprint recognition mode. You can change current recognition
mode
of
the
terminal
through
⑤
Facial/Fingerprint
Switch
Key,
the
Facial/Fingerprint Key in ⑨ Screen Shortcut Keys or related key in ⑩ Keyboard
Shortcut Keys.
⑧Attendance Status: Current attendance status is displayed. This key is hidden
when ⑨ Screen Shortcut Keys are displayed.
⑨Screen Shortcut Keys: Press related shortcut keys to display the attendance
status or enter the functional interface quickly. Users can customize the function of
each shortcut key. For details, see 8 Keyboard.
⑩Keyboard Shortcut Keys: The Keyboard Shortcut Keys have a one-to-one
relationship with ⑨ Screen Shortcut Keys. Press related shortcut keys to display the
attendance status or enter the functional interface quickly.
-7-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.8 Verification Modes
1.8.1 Fingerprint Verification
(1)
1:N fingerprint verification
In the fingerprint verification mode, the terminal compares current fingerprint
collected by the fingerprint collector with all fingerprint data on the terminal.
1. To enter the fingerprint verification
mode (Figure 1 on the right), you can:
A) Press [Facial/Fingerprint Switch Key]
on the screen, or
B) Press [Facial/Fingerprint] shortcut
key on the screen, or
C) Press the keyboard shortcut key
[F6].
2. Press your finger on the fingerprint
collector by adopting the proper finger
placement. For details, see 1.1 Finger
Placement.
3. If the verification is successful, an
interface as shown in Figure 2 on the
right will be displayed.
4. If the verification is not successful, an
interface as shown in Figure 3 on the
right will be displayed.
-8-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
(2)
1:1 fingerprint verification
In the 1:1 fingerprint verification mode, the
terminal compares current fingerprint
collected through the fingerprint collector
with that in relation to the user ID entered
through keyboard. Adopt this mode only
when it is difficult to recognize the fingerprint.
1. To enter the 1:1 recognition mode, you can:
A) Press [1:1/1:G] on the screen, as shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For
details, see 8 Keyboard.
2. Enter user ID and then press the
"Fingerprint” icon (Figure 2 on the right) to
enter 1:1 fingerprint recognition mode. If
the
prompt
“Unregistered
user!”
is
displayed, the user ID is nonexistent or
the user ID bearer has not enrolled his/her
fingerprint.
3. Press your finger on the fingerprint
collector by adopting the proper finger
placement. For details, see 1.1 Finger
Placement.
4. If the verification is successful, an
interface as shown in Figure 3 on the right
will be displayed. 4. If the verification is not successful, an interface as shown in
Figure 4 on the right will be displayed.
-9-
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.8.2 Facial Verification
(1)
1:G facial verification
Current group No. is displayed on the facial recognition interface. Users in
current group can perform facial comparison directly. Users of another group
can perform facial comparison only after
entering the group No. or selecting it using
the shortcut key. And the system will set
the group entered or selected by users to
be the current group instantly.
1. To enter the 1:G recognition mode, you can:
A) Press [1:1/1:G] on the screen, as shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For
details, see 8 Keyboard.
2. Enter user Group No. and then press
the "1:G” icon (Figure 2 on the right) to
enter 1:G fingerprint recognition mode.
3. Compare the facial in a proper way. For
details, see 1.1 Standing Position and
Posture, and Facial Expression. Current
Group No. is displayed on the comparison
interface, as shown in Figure 3 on the right.
Note: Check whether you are in current
group; if not, return to Step 1.
4. If the verification is successful, an
interface as shown in Figure 4 on the right
will be displayed.
- 10 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
(2)
1:1 facial verification
In the 1:1 facial verification mode, the
terminal compares current facial collected
through the facial collector with that in
relation to the user ID entered through
keyboard. Adopt this mode only when it is difficult to recognize the facial.
1. To enter the 1:1 recognition mode, you can:
A) Press [1:1/1:G] on the screen, as shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For details, see 8 Keyboard.
2. Enter user ID and then press the "1:1
Facial” icon (Figure 2 on the right) to enter
1:1 facial recognition mode. If the prompt
“Unregistered user!” is displayed, the user
ID is nonexistent or the user ID bearer has
not enrolled his/her face in the system.
3. Compare the facial in a proper way. For
details, see 1.1 Standing Position and
Posture, and Facial Expression. Current
Group No. is displayed on the comparison
interface, as shown in Figure 3 on the right.
4. If the verification is successful, an
interface as shown in Figure 4 on the right
will be displayed. The system will return to
the main interface if the verification is not
passed within 20 seconds.
- 11 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.8.3 Password Verification
In the password verification mode, the terminal compares the password entered with
that in relation to the user ID.
1.
To enter the password verification mode,
you can:
A) Press [1:1/1:G] on the screen, as
shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the
screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For
details, see 8 Keyboard.
2.
Enter the user ID and then press the "Key”
icon (Figure 2 on the right) to enter
password verification mode. If the prompt
“Unregistered user!” is displayed, the user
ID is nonexistent or the user ID bearer has
not enrolled his/her password in the
system.
3.
Enter the password and press the “OK”
icon to start the password comparison, as
shown in Figure 3 on the right.
4.
If
the
verification
is
successful,
an
interface as shown in Figure 4 on the right
will be displayed.
- 12 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
1.8.4 ID Card Verification
Only the products with a built-in ID card module support the ID card verification. The
products with a built-in ID card module support the following two verification modes:
ID Card Only: Users only need to swipe their ID cards for verification.
ID + Facial Verification: After passing the ID card verification, you also need to
perform facial verification.
For the settings of these two verification modes, see 5.5 Attendance Parameters.
1)
ID Card Only
1. If you have your ID card number enrolled in the system, you can pass the
verification by swiping your ID card at the swiping area in a proper way.
2. If the verification is successful, an
interface as shown in Figure 1 on the
right will be displayed.
3. If the verification is not successful, an
interface as shown in Figure 2 on the
right will be displayed.
- 13 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
2)
ID + Facial Verification
1. Swipe your ID card properly at the
swiping area to enter the 1:1 facial
verification mode, as shown in Figure 1 on
the right:
2. Compare the facial in a proper way. For
details, see 1.1 Standing Position and
Posture, and Facial Expression.
3. If the verification is successful, an
interface as shown in Figure 3 on the right
will be displayed. The system will return to
the main interface if the verification is not
passed within 20 seconds.
- 14 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
2. Main Menu
There are two types of rights respectively granted to two types of users: the ordinary
users and administrators. Ordinary users are only granted the rights of facial,
fingerprint, password or card verification, while administrators are granted the
access to the main menu for various operations apart from having all the privileges
granted to ordinary users.
Press [Menu] on the initial interface to access the main menu, as shown in the
following figure:
Any user can access the main menu by pressing the [Menu] key if the
system is free from administrators. After administrators are configured
on the terminal, the terminal needs to verify the administrators’ identity
before granting them access to the main menu. To ensure terminal
security, it is recommended to set an administrator when using the
terminal initially. For detailed operations, see 3.1.8.
- 15 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
The main menu includes ten submenus and three shortcut keys, as shown in the
following figure:
Return to Initial Interface
Add a User
Set Date/Time
System Information
User Mgt.: Through this submenu, you can browse the user information stored on
the terminal, including the user ID, name, fingerprint, facial, card, password, rights
and group No.; add, modify or delete the user information.
Comm.: Through this submenu, you can set related parameters for communication
between the FFR terminal and PC, including the IP address, gateway, subnet mask,
baud rate, equipment No. and communication password.
System: Through this submenu, you can set system-related parameters, including
the basic parameters, interface parameters, fingerprint, facial and attendance
parameters, to enable the FFR terminal to meet user requirements to the greatest
extent in terms of functions and display.
Data Mgt.: Through this submenu, you can perform management of data stored on
the FFR terminal, for example, deleting the attendance record, all data and
promotional pictures, purging management rights and resetting the FFR terminal to
factory defaults.
Dn/Upload: Through this submenu, you can import user information and attendance
- 16 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
data stored in a USB disk to related software or other fingerprint recognition
equipment.
Keyboard: Through this submenu, you can customize six shortcut keys. Related
status will be displayed by pressing related status key.
Auto Test: This submenu enables the system to automatically test whether functions
of various modules are normal, including the screen, collector, voice, facial,
keyboard and clock tests.
Calibration: When the touch screen is less sensitive to the touch, you can calibrate
the screen on the calibration interface through this submenu.
Bell: Through this submenu, you can set the alarm time and duration.
Access: Through this submenu, you can set the parameters of the electronic locks
and related access control devices.
- 17 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3. User Management
Browse the user information, including the user ID, name, fingerprint, face, ID card,
password, rights and the group that the user belongs to. Add, edit or delete the basic
information of users.
Press [User Management] on the main menu interface to display the user
management interface.
①Return to the Menu interface
②Query a user
③Add a user
④Scroll bar
⑤User list area
⑥Character selection area
The user is an administrator.
The user has enrolled his/her fingerprint.
The user has enrolled his/her facial image.
The user has enrolled his/her ID card.
The user has enrolled his/her password.
Note:
1)
In User List Area, users are listed in alphabetical order by last name. If you
select a user in User List Area, you can access the editing interface of this
user to edit or delete related user information.
2)
In Character Selection Bar, users are listed in alphabetical order by last name
by default and you can locate the desired user quickly. You can press [Query]
- 18 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
to locate and query a user through the user ID. For details, see Section 3.4
Querying a User.
3.1. Adding a User
Press [Add] on the [User Mgt.] interface to display the [Add User] interface as shown
below.
User ID: Enter a user ID. 1- to 9-digit user IDs are supported by default.
Name: Enter a user name. 12-character user names are supported by default.
Fingerprint: Enroll a user’s fingerprint and the FFR terminal displays the number of
enrolled fingerprints. A user can enroll 10 fingerprints at maximum.
Face: Enroll a user’s face.
Card: Enroll a user's ID card.
Password: Enroll a user’s password. 1- to 8-digit passwords are supported by default.
Role: Set the rights of a user. A user is set to ordinary user by default and can also
be set to administrator. Ordinary users are only granted the rights of facial,
fingerprint or password verification, while administrators are granted the access to
the main menu for various operations apart from having all the privileges granted to
ordinary users.
Group No.: Set the group that the user belongs to. Valid group No.: 1–24.
Photo: Enroll a user’s photo. During user verification, the user’s photo is displayed on screen.
The ID card & photo is an optional function. If you need this function, please
consult our commercial representatives or fore-sale technical support
personnel.
- 19 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.1 Entering a User ID
The FFR terminal automatically allocates an ID starting from 1 for every user in
sequence. If you use the ID allocated by the FFR terminal, you may skip this section.
1.
Press [User ID] on the [Add User]
interface
to
display
the
user
ID
management interface, as shown in
Figure 1 on the right.
Tip: The user ID can be modified
during initial enrollment, but once
enrolled, it cannot be modified.
2.
On the displayed keyboard interface,
enter a user ID and press <OK> as
shown in Figure 2 on the right. If a
prompt message “The user ID already
exists!” is displayed, enter another ID.
Tip: The FFR terminal supports 1- to
9-digit user IDs by default. If you
need to extend the length of current user ID numbers, please consult our
commercial representatives or fore-sale technical support personnel.
3.
After the user ID is entered, an interface
is displayed as shown in Figure 3 on the
right. Press [Save] to save current
information and return to the previous
interface. Press [User Mgt.] to return to
the previous interface without saving
current information.
- 20 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.2 Entering a Name
Enter a user name through the keyboard.
1. Press [Name] on the [Add User]
interface to display the name input
interface, as shown in Figure 1 on the
right.
2.
On the displayed keyboard interface,
enter a user name and press [X] as
shown in Figure 2 on the right. For
details of operations on keyboard
interface,
see
“Keyboard
Instructions”.
Tip: The FFR terminal supports the 1- to 12-character names by default.
3.
After the user name is entered, the
interface is displayed as shown in
Figure 3 on the right. Press [Save] to
save current information and return to
the previous interface. Press [User
Mgt.]
to
return
to
the
previous
interface without saving current information.
- 21 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.3 Enrolling a Fingerprint
1. Press [Fingerprint] on the [Add User]
interface
to
display
the
[Enroll
Fingerprint] interface, as shown in Figure
1 on the right.
2.
On the displayed [Enroll Fingerprint]
interface (as shown in the Figure 2 on
the right), place your finger on the
fingerprint collector properly according to
the system prompt. For details, see
“Finger Placement”.
3.
Place the same finger on the fingerprint
collector for three consecutive times
correctly. If the enrollment succeeds,
the system will display a prompt
message “Enrolled Successfully” and
automatically return to the [Add User] interface (as shown in Figure 4 on the
right). If the enrollment fails, the system will display a prompt message and
return to the [Enroll Fingerprint] interface. In this case, you need to repeat the
operations of step 2.
4.
You can back up the enrolled fingerprint
of a user by pressing [Fingerprint]. A
user
can
enroll
10
fingerprints
at
maximum.
- 22 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
5.
Press [Save] to save current information and return to the previous interface.
Press [User Mgt.] to return to the previous interface without saving current
information.
3.1.4 Enrolling a Password
1.
Press [Password] on the [Add User]
interface
to
display
the
password
management interface, as shown in Figure
1 on the right.
2.
On the displayed keyboard interface, enter a password and press <OK> as
shown in Figure 2 on the right. Re-enter
the password according to the system
prompt and then press <OK>.
Tip: The FFR terminal supports the 1to 8-digit passwords by default.
3.
After the password is entered, an interface
is displayed as shown in Figure 3 on the
right.
Press
[Save]
to
save
current
information and return to the previous
interface. Press [User Mgt.] to return to the
previous interface without saving current information.
- 23 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.5 Enrolling a Face
1.
Press [Face] on the [Add User] interface
to display the face enrollment interface,
as shown in Figure 1 on the right.
2.
On
the
displayed
face
enrollment
interface (as shown in Figure 2 on the
right), turn your head to the left and right
slightly, raise and lower your head
according to the voice prompts, so as to
enroll different parts of your face into the
system to assure accurate verification. See 1.1 The distance, Facial
Expression and Stand Pose.
3.
If
your
facial
image
is
enrolled
successfully, the system will display a
prompt message and automatically
return to the [Add User] interface (as
shown in Figure 4 on the right).
4.
Press [Save] to save current information and return to the previous interface.
Press [User Mgt.] to return to the previous interface without saving current
information.
- 24 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.6 Entering a Group No.
The FFR terminal enables the facial comparison function by default. During face
enrollment, the FFR automatically allocates a group No. starting from 1 for every
user in sequence. When the number of users in Group No.1 reaches the upper limit,
the rest users fall under Group No.2 automatically. Up to 100 facial images can be
enrolled in Group No.1 and only 50 facial images can be enrolled in other groups. If
you use the group No. allocated by the FFR terminal, you may skip this section.
1.
Press [Group No.] on the [Add User]
interface to display the group No.
management interface, as shown in
Figure 1 on the right.
2.
On the displayed keyboard interface,
enter your group No. and press <OK> as
shown in Figure 2 on the right.
Tip: A valid group No. contains 1–24
digits.
3.
After the group No. is entered, an
interface is displayed as shown in Figure
3 on the right. Press [Save] to save
current information and return to the
previous interface. Press [User Mgt.] to
return to the previous interface without saving current information.
Tip: Please remember your own group No.
- 25 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.7 Enrolling an ID Card *
1.
Press [Card] on the [Add User] interface
to display the [Enroll Card] interface, as
shown in Figure 1 on the right.
2. The [Punch Card!] interface pops out as
shown in Figure 2 on the right. Swipe
your ID card properly in the swiping area.
For details, see “1.6 Appearance of the
FFR Terminal”.
3.
If the card passes the verification, the
FFR
terminal
displays
a
prompt
message “Read Successfully! Card No.:
**********”, as shown in Figure 3 on the
right, and returns to the [Add User]
interface. Press [Card] to display the enrolled card number as shown in Figure 4
on the right.
4.
Press [Save] to save current information
and return to the previous interface.
Press [User Mgt.] to return to the
previous interface without saving current
information.
- 26 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.8 Modify User Rights
1.
On the [Add User] interface, press [Role:
User]
to
change
the
user
into
an
administrator, as shown in Figure 1 on the
right.
Note: There are two types of rights
respectively granted to two types of
users: the ordinary users and administrators. Ordinary users are only
granted the rights of facial, fingerprint, or password verification, while
administrators are granted the access to the main menu for various
operations apart from having all the privileges granted to ordinary users.
2.
After
the
modification
is
done,
the
interface is as shown in Figure 2 on the
right. Press [Save] to save current
information
and
return
to
previous
interface; press [User Mgt.] to directly
return to previous interface without saving
current information.
- 27 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.1.9 Enroll Photos
If you have enrolled your photo in the system, the system will display your enrolled
photo in addition to your ID and name after you pass the verification.
1.
Press [Photo]
on the [Add User]
interface to display the photo enrollment
interface, as shown in Figure 1 on the
right.
2.
On the photo enrollment interface,
stand naturally in front of the screen.
For details, see 1.1 Standing Position
and Posture, and Facial Expression.
Press [Capture] to display the photo
taken at the lower left corner, as shown
in Figure 3 on the right.
3.
After taking the photo, press [Exit] to
return to previous interface.
4. After the photo is taken, the interface is as
shown in Figure 4 on the right. Press [Save]
to save current information and return to
previous interface; press [User Mgt.] to
directly return to previous interface without
saving current information.
- 28 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.2 Edit a User
Select a user from the User List to enter [User Info] interface.
The User ID cannot be modified, and the other operations are similar to those
performed to add a user. You can re-enroll your fingerprint and facial image, change
your password and modify the management rights and group No.
- 29 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.3 Delete a User
On the [User Info] interface, you can delete
all or partial user information.
1.
Press [Delete] to delete a user, as shown
in Figure 1 on the right.
2.
On the interface displayed (as shown in
Figure 2 on the right), click [YES] to
delete current user and [NO] to return to
previous interface.
3.
On the [User Info] interface, press [Name], [Fingerprint], [Face] or [Password] to
delete related user information.
- 30 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.4 Query a User
To facilitate administrators to locate a user quickly from a large number of enrolled
users, the FFR terminal enables user query by his/her “User ID” and “Name”.
(Location Search)
3.4.1 Query by User ID
1. Press [Query] on the [User Management]
interface to display the User ID query
interface, as shown in Figure 1 on the
right.
2.
Enter the user ID on the displayed
interface, and click [OK] (as shown in
Figure 2 on the right) to locate the cursor
to the desired user (as shown in Figure 3
on the right).
- 31 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
3.4.2 Query by Name
On the [User Management] interface, enter the user name through the “Character
Selection Bar” to locate the cursor to the desired user, as shown in the following
figure:
By selecting a character from the “Character Selection Bar”, you can quickly locate
the users whose names start with this character. Users are listed in alphabetical
order by last name by default.
- 32 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
4. Communication-related Settings
You can set related parameters for the communication between the FFR terminal
and PC, including the IP address, gateway, subnet mask, baud rate, equipment No.
and communication password.
4.1 Network Settings
When the FFR terminal communicates with the PC over Ethernet, you need to check
the following settings:
IP Address: The IP address is 192.168.1.201 by default and can be changed as
required; the IP address of the FFR terminal and that of the PC cannot be duplicated.
Subnet Mask: The subnet mask is 255.255.255.0 by default and can be changed as
required.
Gateway: The gateway is 0.0.0.0 by default. If the FFR terminal and the PC are not
located in the same network segment, you need to set the gateway.
- 33 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
4.2 Serial Port Settings
When the FFR terminal communicates with the PC over serial ports (RS232/RS485), you need
to check the following settings:
RS232: This parameter is used to enable or disable the RS232 communication. If the RS232
communication cables are used, set this parameter to “ON”.
RS485: This parameter is used to enable or disable the RS485 communication. If the RS485
communication cables are used, set this parameter to “ON”.
Baud Rate: This parameter is used to set the baud rate for the communication between the
FFR terminal and the PC. It includes five options: 9600, 19200, 38400, 57600, and 115200.
The high baud rate is recommended for the RS232 communication to achieve high
communication speed, while the low baud rate is recommended for the RS485 communication
to achieve stable low-speed communication.
Device ID: This parameter is used to set the ID of device from 1 to 254. If the RS232/RS485
communication is adopted, you need to enter the device ID on the software communication
interface.
Comm Key: To enhance the security of attendance data, you can set a password for the
connection between the FFR terminal and PC. Once the password is set, you can connect the
PC with the FFR terminal to access the attendance data only after entering the correct
password. The default password is 0 (that is, no password). Once a password is set, you need
to enter this password before connecting the PC software with the FFR terminal; otherwise, the
connection is unsuccessful. 1- to 6-digit passwords are supported.
Considering the massive data including the fingerprint and facial templates
stored in the FFR terminal, it is recommended to transfer the data between the
FFR terminal and PC over network to enhance the transfer speed.
- 34 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
4.3 Wiegand Output
Wiegand Format: The system has two built-in formats Wiegand 26-bits and
Wiegand 34-bits, and also supports the format customization function to meet
individualized requirements.
Failed ID: refers to the value output by the system upon verification failure. The
output format is subject to the setting of “Wiegand Format”. The default value scope
of Failed ID is 0–65535.
Site Code: The site code is used for customized Wiegand format. The site code is
similar to the device ID, but the site code is customizable and can be duplicated
among different devices. The default value scope of the site code is 0–255.
Pulse Width: refers to the width of the Wiegand pulse in microseconds. The default
value scope of the pulse width is 1–1000.
Pulse Interval: refers to the interval of the Wiegand pulse in microseconds. The
default value scope of the pulse width is 1–10000.
Output: refers to the contents output upon successful verification. You can select the
“User ID” or “Card Number” as the output.
4.3.1 Wiegand 26-bits Output Description
The system has a built-in Wiegand 26-bits format. Press [Wiegand Format], and
select “Standard Wiegand 26-bits”.
- 35 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
The composition of the Wiegand 26-bits format contains 2 parity bits and 24 bits for
output contents (“User ID” or “Card Number”). The binary code of 24-bits represent
up to 16,777,216 (0–16,777,215) different values.
1
2
Even parity
25 26
User ID/Card Number
Odd parity bit
Definition of Fields:
Field
Meaning
Even parity bit
Judged from bit 2 to bit 13. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
even parity bit is 1.
User
ID/Card
User ID/Card Number (Card Code, 0–16777215)
Number (bit 2-bit 25)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 14 to bit 25. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the odd
parity bit is 0.
For example, for a user with user ID of 12345, the enrolled card number is
0013378512 and the failed ID is set to 1.
1) When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
00000000000110000001110011
Even parity bit
User ID = Binary code of 12345
Odd parity bit
2) When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
- 36 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
11100110000100011110100000
Even parity bit User ID = Binary code of 0013378512
Odd parity bit
3) The Wiegand output is as follows upon verification failure:
00000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
Note: If the output contents exceed the scope allowed for the Wiegand format,
the last several bits will be adopted and first several bits are automatically
discarded. For example, the user ID 888 888 888 is 110 100 111 110 110 101 111
000 111 000 in binary format. Wiegand26 only supports 24 bits, that is, it only
outputs the last 24 bits, and first 6 bits “110 100” are automatically discarded.
4.3.2 Wiegand 34-bits Output Description
The system has a built-in Wiegand 34-bits format. Press [Wiegand Format], and
select “Standard Wiegand 34-bits”.
The composition of the Wiegand 34-bits format contains 2 parity bits and 32 bits for
output contents (“User ID” or “Card Number”). The binary code of 32-bits represent
up to 4,294,967,296 (0–4,294,967,295) different values.
1
2
33 34
Even
User ID/Card Number
Odd parity bit
Table 2 Definition of Fields
Field
Meaning
Even parity bit
Judged from bit 2 to bit 17. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
even parity bit is 1.
- 37 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
User
ID/Card
User ID/Card Number (Card Code, 0–4,294,967,295)
Number (bit 2-bit 33)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 18 to bit 33. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
odd parity bit is 0.
For example, for a user with user ID of 123456789, the enrolled card number is
0013378512 and the failed ID is set to 1.
1) When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
0000001110101101111001101000101011
Even parity bit
User ID = Binary code of 123456789
Odd parity bit
2) When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
0000000001100110000100011110100001
Even parity bit
User ID = Binary code of 0013378512
Odd parity bit
3) The Wiegand output is as follows upon verification failure:
0000000000000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
4.3.3 Customized Format
Apart from the two built-in formats Wiegand 26-bits and Wiegand 34-bits, the
system also supports the format customization function to meet individualized
requirements.
The customized format consists of two character strings: the data bits and parity
bits. These two character strings need to be defined separately. Data bits define the
- 38 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
number of binary bits output by Wiegand as well as the meaning of each bit. The
data bits output by Wiegand can be a card number (C), site code (s), facility code (f),
manufacturer code (m) and parity bits (p). Parity bits define the check mode of each
bit in data bits and ensure the correctness of data bits during transfer through the
parity check. The parity bits can be set to odd check (o), even check (e) and both
odd check and even check (b). There exists a one-to-one correspondence
relationship between the data bits and parity bits.
For example, the Wiegand26 can be customized as follows:
Definition of data bits: pssssssssccccccccccccccccp
Definition of parity bits: eeeeeeeeeeeeeooooooooooooo
Note: Wiegand26 consists of 26 bits. The first bit is the even parity bit of bits 2 to 13;
the 26th bit is the odd parity bit of bits 14 to 25; the second to the ninth bits are the
site code; the 10th to the 25th bits are the card number.
For details about the Wiegand protocol, see Appendix 3 Introduction to Wiegand.
To customize Wiegand format, proceed as follows:
1)
2)
Select [Define Format] and the [Set] key is then enabled.
Press [Set] to display the [User Define Format] interface, as shown in the
following figure:
3)
Click the entry box below “Card Format” to display the following interface:
- 39 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Display input in real-time
Backspace
Display the number of
bits in real-time
Cancel Input
Confirm Input
Clear Input
Characters used to define data bits and their meanings:
c: indicates the card number, that is, the output contents, it can be set to
User ID/Card Number through menu operations.
f: indicates the facility code which is 0 by default. It is not configurable. To
modify it, please contact the equipment supplier.
m: indicates the manufacturer code which is 0 by default. It is not
configurable. To modify it, please contact the equipment supplier.
p: indicates the parity position.
s: indicates the site code which can be set from 0 to 255 by default.
4)
Click the entry box below “Parity Format” to display the following interface:
Characters used to define parity bits and their meanings:
o: indicates the odd check, that is, there is an odd number of 1’s in the bit
sequence (including one parity bit). For example, for 1000110(0), the
parity bit is 0 and there are already three 1’s. After 0 is suffixed to 1000110,
there is still an odd number of 1’s.
e: indicates the even check, that is, there is an even number of 1’s in the
- 40 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
bit sequence (including one parity bit). For example, for 1000110(1), the
parity bit is 1 and there are already three 1’s. After 1 is suffixed to 1000110,
there is an even number of 1’s.
b: indicates both odd check and even check.
For example: Definitions of several universal Wiegand formats.
Wiegand34
Data bits:
pccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeooooooooooooooooo
Note: Wiegand34 consists of 34 bits. The first bit is the even parity bit of bits 2
to 17; the 34th bit is the odd parity bit of bits 18 to 33; the second to the ninth
bits are the site code; the 10th to the 25th bits are the card number.
Wiegand37a
Data bits: pmmmmsssssssssssscccccccccccccccccccp
Parity bits: oeobeobeobeobeobeobeobeobeobeobeobeoe
Note: Wiegand37a consists of 37 bits. The first bit is the odd parity bit of bits 3,
4, 6, 7, 9, 10, 12, 13, 15, 16, 18, 19, 21, 22, 24, 25, 27, 28, 30, 31, 33, 34 and
36; the 37th bit is the odd parity bit of bits 2, 4, 5, 7, 8, 10, 11, 13, 14, 16, 17, 19,
20, 22, 23, 25, 26, 28, 29, 31, 32, 34 and 35; bits 4, 7, 10, 13, 16, 19, 22, 25, 28,
31 and 34 participate in both odd and even parity check. Bits 2 to 5 are
manufacturer code; bits 6 to 17 are the site code; bits 18 to 36 are the card
number.
Wiegand37
Data bits:
pmmmffffffffffssssssccccccccccccccccp
- 41 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Parity bits:
eeeeeeeeeeeeeeeeeeooooooooooooooooooo
Note: Wiegand37 consists of 37 bits. The first bit is the even parity bit of bits 2
th
to 18; the 34 bit is the odd parity bit of bits 19 to 36; the second to the fourth
bits are the manufacturer code; the 5th to the 14th bits are facilitate code; the
15th to the 20th bits are the site code; the 21st to the 36th bits are the card
number.
Wiegand50
Data bits: pssssssssssssssssccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeeeeeeeeooooooooooooooooooooooooo
Note: Wiegand50 consists of 50 bits. The first bit is the even parity bit of bits 2
to 25; the 50th bit is the odd parity bit of bits 26 to 49; the second to the 16th bits
are the site code; the 17th to the 49th bits are the card number.
- 42 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
5. System Configuration
Through the [System] menu, you can set system-related parameters, including the
basic parameters, interface parameters, fingerprint, facial and attendance
parameters, to enable the terminal to meet user requirements to the greatest extent
in terms of functions and display.
5.1 Basic Parameters
Date/Time: This parameter is used to set the date and time of the FFR terminal.
Date Format: This parameter is used to set the format of the date displayed on the
initial interface of the FFR terminal.
Keyboard Beep: This parameter is used to set whether to generate beep sound in
response to every keyboard touch. Select “ON” to enable the beep sound, and select
“OFF” to mute.
Voice: This parameter is used to set whether to play voice prompts during the
- 43 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
operation of the FFR terminal. Select “ON” to enable the voice prompt, and select
“OFF” to mute.
Volume (%): This parameter is used to adjust the volume of voice prompts.
Power Key: This parameter is used to set whether to lock the power key. Select
“ON” to disable the power key. If you select “OFF” and press the power key, the FFR
terminal will be shut down in three seconds.
5.2 Interface Parameters
Language: This parameter is used to display the current language used by the FFR
terminal. For multilingual-capable FFR terminals, you can switch between different
languages through this parameter.
Display Style: This parameter is used to set the time display mode of the initial
interface. Select “ON” to adopt the 24-hour display mode. Select “OFF” to adopt the
12-hour display mode.
Toolbar Style: This parameter is used to display style of the shortcut keys on the
initial interface. It can be set to “Auto Hide” and “Permanent Display”. By selecting
“Auto Hide”, you can manually display or hide the toolbar. By selecting “Permanent
Display”, you can permanently display the toolbar on the initial interface.
Default Verify Mode: This parameter is used to set the default verification mode, that
is, the "Fingerprint" or “Face” verification mode.
Picture Delay (S): This parameter is used to set the picture cycle interval (value
scope: 3─999 seconds).
- 44 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Sleep Time (S): This parameter is used to specify a period after which the FFR
terminal is put in sleep mode if not operated within this period. You can bring up the
FFR terminal from sleep by pressing any key or touching the screen.
5.3 Fingerprint Parameters
1: 1 Threshold: This parameter is used to set the threshold of matching between
current fingerprint and the fingerprint template enrolled in the FFR terminal in the 1:1
verification mode. If the similarity between current fingerprint and the fingerprint
template enrolled in the FFR terminal is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
1: N Threshold: This parameter is used to set the threshold of matching between
current fingerprint and the fingerprint template enrolled in the FFR terminal in the 1:N
verification mode. If the similarity between current fingerprint and the fingerprint
template enrolled in the FFR terminal is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
The recommended thresholds are as follows:
Threshold
False
Rejection
Rate
False
1: N
1:1
(FRR)
Acceptance
Rate (FAR)
- 45 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
High
Low
45
25
Medium
Medium
35
15
Low
High
25
10
1:1 Retry Times: This parameter is used to set the retry times in the event of failure
of 1:1 verification or password verification due to absence of fingerprint enrollment or
improper finger placement, so as to avoid repetitive operations.
Algorithm Version: This parameter is used to select the fingerprint algorithm
version between 9.0 and 10.0. Please select the algorithm version with caution
because the fingerprint templates of these two algorithm versions are incompatible.
Fingerprint Image: This parameter is used to set whether to display the fingerprint
image on the screen during fingerprint enrollment or comparison. It has two values:
Permanent Display and No Display.
5.4 Face Parameters
1: 1 Threshold: This parameter is used to set the threshold of matching between
current face and the facial template enrolled in the FFR terminal in the 1:1
verification mode. If the similarity between current face and the facial template
enrolled in the FFR terminal is larger than this threshold, the matching is successful;
otherwise, the matching is not successful. The valid value scope is 55─120. The
higher the threshold, the lower the FAR and the higher the FRR, and vice versa.
1:1: N Threshold: This parameter is used to set the threshold of matching between
current face and the facial template enrolled in the FFR terminal in the 1:N
- 46 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
verification mode. If the similarity between current face and the facial template
enrolled in the FFR terminal is larger than this threshold, the matching is successful;
otherwise, the matching is not successful. The valid value scope is 65─120. The
higher the threshold, the lower the FAR and the higher the FRR, and vice versa.
The recommended thresholds are as follows:
FRR
High
FAR
1: N
Low
Medium
Low
Threshold
1:1
90
Medium
High
80
80
75
70
65
Enroll Mode: This parameter is used to select the facial enrollment mode between
“Combined Enroll” and “Face”. In the “Combined Enroll” mode, users need to enroll
their fingerprints or passwords after facial enrollment; in the “Face” mode, users only
need to enroll their facial images. The “Face” mode is unavailable for the
administrators because the “Combined Enroll” mode is mandatory for them by
default.
Exposure: This parameter is used to set the exposure value of the camera.
Gain: This parameter is used to set the gain value of the camera.
Quality: This parameter is used to set a quality threshold for the facial images
obtained. The FFR terminal accepts the facial images and processes them by
adopting the facial algorithm when their quality is higher than the threshold;
otherwise, it filters these facial images.
Note: Improper adjustment of the Exposure, Gain and Quality parameters may
severely affect the performance of the FFR terminal. Please adjust the
Exposure parameter only under the guidance of the after-sales service
personnel from our company.
- 47 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
5.5 Log Settings
Log Alert: When the available space is insufficient to store the specified number of
attendance records, the FFR terminal will automatically generate an alarm. (Value
scope: 1─99)
Dup. Punch Period (m): If a user’s attendance record already exists and the user
punches in again within the specified period (unit: minute), his/her second
attendance record will not be stored. (Value scope: 1─60 minutes)
Workcode Mode: This parameter is used to select the work code input mode among
Mode 1, Mode 2 and None during attendance verification. If you select Mode 1, the
attendance verification starts after you input the work code on the initial interface; if
you select Mode 2, the attendance verification starts before you input the work code
on the initial interface; if you select None, you do not need to input the work code
during attendance verification on the initial interface. For the input of the work code,
see 6.2 Workcode.
Card Only: If this parameter is set to “YES”, you pass the verification only after card
verification. If this parameter is set to “NO”, you need to verify your face or fingerprint
after card verification.
- 48 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
5.6 Update
You can upgrade the firmware program of the FFR terminal by using the upgrade file
in the USB disk through this parameter.
If you need the firmware upgrade file, please contact our technical support
personnel. Generally the firmware upgrade is not recommended.
- 49 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
6. Data Management
Through the [Data Mgt.] menu, you can perform management of data stored on the
FFR terminal, for example, deleting the attendance record, all data and promotional
pictures, purging management rights and resetting the FFR terminal to factory
defaults.
Delete Transactions: Delete all the attendance records.
Delete All Data: Delete all the information of enrolled personnel, including their
fingerprints, facial images and attendance records.
Clear Administrator: Change all administrators to ordinary users.
Delete Picture: Purge the promotional pictures uploaded from USB disks to the FFR
terminal. (For details on how to upload promotional pictures, see “5.4 Upload
Picture”.)
Restore to Factory Settings: Restore all parameter settings on the FFR terminal to
factory settings.
Record: Query the attendance records of employees within a specified time range.
WorkCode: Add, edit or delete the work codes of employees.
The employee information and attendance records
will not be deleted during restoration to factory
- 50 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
6.1 Query a Record
After check-in successfully, the employee’s attendance records are saved in the FFR
terminal. You can easily query these attendance records.
User ID: Enter the user ID of the employee to query. If this field is left blank, you can
query the attendance records of all the employees. If you enter a user ID, you can
query the attendance record of the employee with this user ID.
Query Time Period: Select a time period to query, including the customized time
period, yesterday, this week, last week, this month, last month, and all time periods.
Start and End: When you select a customized time period, you need to input a start
time and an end time. When you select other options for time period, the start and
end time will be automatically adjusted to the related time.
After setting the query conditions, press [Query]
and the records that meet the specified query
conditions will be displayed on screen.
Select the row where the desired record is
located, you can query the detailed information
of this record, for example, the detailed
attendance record of the employee with user ID
2 on January 7th.
- 51 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
6.2 Work Code
Employees’ salaries are subject to their attendance records. Employees may be
engaged in different types of work which may vary with time periods. Considering the
salaries vary with work types, the FFR terminal provides a parameter to indicate the
corresponding work type for every attendance record to facilitate rapid
understanding of different attendance situations during the handling of attendance
data.
1.
Add a work code
1) Press [Add] on the [WorkCode]
interface (as shown in Figure 1 on the
right) to display the [Add] interface.
No.: A digital code of the work code.
Label: The meaning of the work code.
2) Press the corresponding entry button
of [No.] on the [Add] interface (as shown
in Figure 2 on the right) to display the
No. entry interface. On this interface,
enter a No.
3) Press the corresponding entry button
of [Label] on the [WorkCode] interface
(as shown in Figure 3 on the right) to
display the text entry interface. On this
interface, enter a label of work code.
(See Appendix 1 Text Entry Operation
Instruction)
- 52 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
2.
Edit and delete a work code
1) Press the row of a work code on the
[WorkCode] interface (as shown in
Figure 1 on the right) to display the [Edit]
interface.
2) To edit this work code, enter a new
No. and label with the same operation
steps as described in “Add a work
code”.
3) To delete this work code, press
[Delete] (as shown in Figure 3 on the
right).
4) On the displayed prompt interface,
press <YES> to confirm the deletion of
this work code, and press <NO> to
cancel the deletion operation (as shown
in Figure 4 on the right).
- 53 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
7. USB Disk Management
Through the [Dn/Upload] menu, you can import user information and attendance data
stored in a USB disk to related software or other fingerprint recognition equipment.
Download Transactions: Import all the attendance data from the FFR terminal to a USB
disk.
Download User: Import all the user information, fingerprints and facial images from the
FFR terminal to a USB disk.
Download user photos*: Import the employees’ photos from the FFR terminal to a USB
disk.
Only several types of the FFR terminals support the
download of user photos.
Upload User: Upload the user information, fingerprints and facial images stored in a USB
disk to the FFR terminal.
Upload User Photo: Upload the JPG documents that are named after the user IDs and
stored in a USB disk to the FFR terminal, so that user photos can be displayed after the
employees pass the verification. See Appendix 4 Photo ID Function.
Upload Picture: Upload the JPG documents with “ad_” as initial letters of document
names stored in a USB disk to the FFR terminal. After the upload, these pictures can be
displayed on the initial interface of the FFR terminal. (For details on picture specifications,
see Appendix 2.)
- 54 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
8. Keyboard Definitions
You can define six shortcut keys as attendance status shortcut keys or functional
shortcut keys. On the main interface of the FFR terminal, press corresponding keys
and the attendance status will be displayed or the function interface will be rapidly
displayed.
1.
Press [Keyboard] on the main menu
interface
to
display
the
[Keyboard]
interface, as shown in Figure 1 on the right.
2.
All the defined shortcut keys and their
functions are listed on the [Keyboard]
interface (as shown in Figure 2 on the
right). Press [Add] to display the shortcut
key adding interface. Press a shortcut key
in the list to display the shortcut key
editing interface.
3.
Add and edit the functional introduction of
interface
Shortcut Key: Options include: F1–F6.
Note: When the FFR terminal supports
both fingerprint and face recognition
modes, F6 is defined as a recognition
mode switch key by default and cannot
be modified.
Function: You can set the functions of
- 55 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
different shortcut keys, such as functional shortcut keys, attendance status
shortcut key and work code shortcut key.
Functional shortcut status include: 1:1/1:G, Face Group No.1, Face Group
No.2, Face Group No.3, Face Group No.4 and Face Group No.5. The setting
interface is shown in Figure 3 on the right.
The
status
shortcut
Check-In,
Check-Out,
Overtime
Check-In,
keys
include:
Leave,
and
Back,
Overtime
Check-Out. The setting interface is
shown in Figure 4 on the right. When
setting the attendance status shortcut
keys, you can also set the “Auto Switch” parameter. When “Auto Switch” is
enabled, the FFR terminal automatically switches the attendance status at the
specified time. The “Auto Switch” setting
interface is as shown in Figure 5 on the
right.
The work code shortcut key setting
interface is as shown in Figure 6 on the
right.
- 56 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
9 Auto Test
The auto test enables the system to automatically test whether functions of various
modules are normal, including the screen, collector, voice, facial, keyboard and
clock tests.
Screen Test: The FFR terminal automatically tests the display effect of the color
TFT display by displaying full color, pure white and pure black and checks whether
the screen displays properly. You can continue the test by touching the screen or
exit it by pressing [Auto Test].
Voice Test: The FFR terminal automatically tests whether the voice files are
complete and the voice quality is good by playing the voice files stored in the
terminal. You can continue the test by touching the screen or exit it by pressing [Auto
Test].
Keyboard Test: The FFR terminal tests whether every key on the keyboard works
normally. Press any key on the [Keyboard Test] interface to check whether the
pressed key matches the key displayed on screen. The keys are dark-gray before
pressed, and turn blue after pressed. Press [Auto Test] to exit the test.
Fingerprint Test: The FFR terminal automatically tests whether the fingerprint
collector works properly by checking whether the fingerprint images are clear and
acceptable. When the user places his/her finger in the fingered guide, the collected
fingerprint image is displayed on the screen in real-time. Press [Auto Test] to exit the
test.
- 57 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Face Test: The FFR terminal automatically tests whether the camera works properly
by checking whether the collected facial images are clear and acceptable. Press
[Auto Test] to exit the test.
Time Test: The FFR terminal tests whether its clock works properly by checking the
stopwatch of the clock. Touch the screen to start counting, and touch it again to stop
to check whether the counting is accurate. Press [Auto Test] to exit the test.
- 58 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
10 Screen Calibration
You can perform all the menu operations by touching the screen with one of your
fingers or a touch pen. When the touch screen is less sensitive to the touch, you can
perform screen calibration through menu operations.
1.
Press [Menu] on the initial interface to
display the main menu interface.
2.
Press [Calibration] on the main menu
interface to display the screen calibration
interface.
3.
Touch the center of the cross “+”.
4.
Repeat Step 3 following the move of the
“+” icon to different locations on the
screen.
5.
Touch the center of the cross at five
locations on the screen correctly. When
the message “Calibrating screen, pls
wait……” is displayed on screen, the
calibration succeeds and the system
automatically returns to the main menu.
If the calibration fails, the system will request recalibration starting from Step 3.
- 59 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
11 Bell Setting
Lots of companies need to ring their bells to signal the start and end of work shifts,
and they usually manually ring their bells or use electric bells. To lower costs and
facilitate management, we integrate the time bell function into the FFR terminal. You
can set the alarm time and duration for ringing the bell based on your requirements,
so that the FFR terminal will automatically play the selected ring tone and trigger the
relay at the alarm time, and stop playing the ring tone after the set duration.
Press [Bell] on the main menu interface to
display the bell setting interface, as shown in
Figure 1 on the right.
1. Add a bell
1)
The displayed bell setting interface (as
shown in Figure 2 on the right) lists all
the bells. Click [Add] to display the [Add]
interface.
2)
On the [Add] interface, set the following
parameters:
Bell Time: This parameter is used to
set a time point when the FFR terminal
automatically plays a bell ring tone
everyday.
Ring Tone: This parameter is used to set the bell ring tone.
Volume: This parameter is used to set the volume of ring tone.
Repeat: This parameter is used to set the alarm times.
- 60 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
State: This parameter is used to set whether to enable the bell.
Bell Type: You can select between internal ringing or external ringing. For
internal ringing, the ring tone is played by the loudspeaker of the FFR terminal.
For external ringing, the ring tone is played by an external electric bell that is
wired with the FFR terminal.
The alarm sounds of the bell and the access control cannot be
concurrently generated by the loudspeaker of the FFR terminal or
externally connected relay. Therefore, when the bell is set to the
external ringing mode, the access limit alarm will automatically
change to the internal ringing mode, and vice versa.
2.
Edit and delete a bell
Press a bell in the list on the bell setting
interface to display the [Edit] interface,
with the similar operation as “Add a
bell”.
Press [Delete] on the [Edit] interface
and the system displays a prompt
window as shown in the figure on the
right. In the prompt window, press
<YES> to delete the current bell and
<NO> to cancel the deletion.
- 61 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
12 Access Control Setting
Through the [Access] menu, you can set the parameters of the electronic locks and
related access control devices.
Lock Delay: indicates the duration for the FFR terminal to place the electric lock in
open state. (Value scope: 1–10 seconds)
DoorSensor Delay: indicates the delay in checking the door sensor after the door is
open. If door sensor state is inconsistent with the normal state set by the door sensor
switch, an alarm will be generated, and this period of time is regarded as the “door
sensor delay”. (Value scope: 1─99 seconds)
DoorSensor Mode: includes the None, Normally Open (NO), and Normally Closed
(NC) modes. “None” indicates that the door sensor switch is not used. “NO” indicates
that the door sensor is open in the normal state. “NC” indicates that the door sensor
is closed in the normal state.
Alarm Delay: indicates the duration from the detection of door sensor exceptions to
the generation of alarm signals. (Value scope: 1─99 seconds)
- 62 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
13 Date/Time Setting
13.1 Set Date/Time
The date and time of the FFR terminal must be set accurately to ensure the accuracy
of attendance time.
1.
Press [Menu] on the initial interface to
display the main menu interface.
2.
Press [Time/Date] on the main menu
interface to
display the time setting
interface.
3.
Select the desired date and time by
pressing ▲ or ▼, or enter the related
values into the date and time entry boxes
through the keyboard (as shown in Figures
3 and 4 on the right).
4.
Press [Save] to save current information
and return to the previous interface. Press
[Cancel] to return to the previous interface
without saving current information.
- 63 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
13.2 Set Daylight Saving Time (DST)
The Daylight Saving Time (DST) is a widely used system of adjusting the official
local time forward to save energy. The uniform time adopted during the
implementation of this system is known as the DST. Typically clocks are adjusted
forward one hour in the summer to make people early to bed and early to rise so as
to make full use of illumination resources and save electricity. Clocks are adjusted
backward in autumn. The specific DST regulations vary with countries.
To meet the DST requirement, the FFR terminal supports the DST function to adjust
forward on hour at ×× (Hour): ×× (Minute) ×× (Day) ×× (Month) and backward one
hour at ×× (Hour): ×× (Minute) ×× (Day) ×× (Month).
1.
Press [Menu] on the initial interface to
2.
Press [Time/Date] on the main menu
display the main menu interface.
interface to display the time setting
interface.
3.
Press [DLST] on the time setting
interface to display the DST setting
interface.
4.
Set the following parameters on the
DST setting interface:
DST Settings: This parameter is used
to enable or disable the DST.
Mode: You can select between Mode 1
and Mode 2.
In Mode 1 (the default mode), the DST is set in the “Month-Day Hour: Minute”
- 64 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
format; in Mode 2, the DST is set in the
“Month-Week-Day
Hour:
Minute”
format.
The value scope of week (WS): 1 – 6. 1
means the first week, 2 the second
week and so on and so forth. The value
scope of day (WK): 0 – 6. 0 means Sunday, 1 means Monday and so on and so
forth.
Start and End: These two parameters are respectively used to set the start
and end time of the DST.
For example, adjust the clock forward one hour at 08: 00 on April 1st, and
backward one hour at 08: 00 on October 1st.
5.
After setting the DST, press [Done] to
return to the time setting interface.
Press [Save] on the time setting
interface to save current settings and
return to the previous interface; press
[Cancel] to directly return to previous
interface without saving current information.
- 65 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
14 System Information
You can check the storage status as well as version information of the FFR terminal
through the [System Information] option.
14.1 Records
The number of enrolled users, administrators and passwords is displayed on the
[Records] interface; the total fingerprint
storage capacity and occupied capacity
as well as the total attendance storage
capacity and occupied capacity are
graphically displayed respectively, as
shown in the following figure:
14.2 Terminal
The terminal name, serial number, version information, vendor and date of
manufacture are displayed on the [Terminal] interface.
- 66 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Appendix
Appendix 1 Text Input Instructions
The FFR terminal supports the input of Chinese and English characters, numbers
and symbols. Press related button to input text. For example, press [Name] to
display the text input interface, as shown in the following figure:
cKeyboard Area
dText Display Area
eText List Area
fExit
gDelete
hEnter
iSpace
jChinese/English Switch Key
kCharacter/Number Switch Key
lUpper/Lower Case Switch Key
- 67 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
To enter a name, proceed as follows:
1.
Press [Name] on the [Add] interface, as
shown in Figure 1 on the right.
2.
Enter the Pinyin characters, and a list of
Chinese characters in relation to the
Pinyin is presented in the text display
area, as shown in Figure 2 on the right.
3.
If the desired character is displayed in
the
text
display
area,
press
this
character. And this character is at the
same time displayed on the [Name]
button, as shown in Figure 3 on the right.
Enter next character by repeating Step
2.
4. After finishing the entry of name, press [X]
to exit keyboard interface and return to
the previous interface.
- 68 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Appendix 2 Rules for Uploading Promotional Pictures
1.
All pictures must be in JPG format as other formats are not supported.
2.
The file name of a promotional picture must be ad_0 - ad_9. For example,
ad_1.jpg is a valid file name.
3.
After a picture is uploaded to the FFR terminal, its name does not change. To
replace this picture, you need to upload a new picture with the same file name to
overwrite it.
4.
The size of each picture cannot exceed 20K; otherwise, the upload will be
unsuccessful.
5.
The recommended resolution of the picture is 320 × 240. Pictures with
resolution higher or lower than 320 × 240 are not recommended.
6.
A maximum of 10 promotion pictures can be uploaded.
- 69 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Appendix 3 Introduction to Wiegand
Wiegand26 is an access control standard protocol established by the Access Control
Standard Subcommittee affiliated to the Security Industry Association (SIA). It is a
non-contact IC card reader interface and output protocol.
Wiegand26 defines the interface between the card reader and controller used in the
access control, security and other related industrial fields. Wiegand26 helps
standardize the work of the card reader designers and controller manufacturers. The
access control products manufactured by our company are also designed by
following this protocol.
Digital Signals
Figure 1 is a sequence diagram in which the card reader sends digital signals in bit
format to the access controller. In this sequence diagram, Wiegand follows the SIA’s
access control standard protocol for the 26-bit Wiegand card reader (one pulse time
ranges between 20us and 100us, and the pulse jump time ranges between 200us
and 20ms). Data1 and Data0 are high level (larger than Voh) signals till the card
reader prepares to send a data stream. The asynchronous low-level pulse (smaller
than Vol) generated by the card reader is sent to the access control panel (The
saw-tooth wave as shown in Figure 1) through Data1 or Data0. Data1 and Data0
pulses will neither overlap nor be generated synchronously. Table 1 lists the
maximum and minimum pulse width (a consecutive pulse) and pulse jump time (time
between pulses) allowed by the F series fingerprint access control terminal.
Table 1 Pulse Time
Symbol
Definition
Typical Value of Reader
Tpw
Pulse Width
100 µs
Tpi
Pulse Interval
1 ms
- 70 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Figure 1 Sequence Diagram
Appendix 4 Photo ID Function
Some FFR terminals also support the Photo ID function. The Photo ID function is
used to display the photo enrolled by a user or stored in a USB disk on the screen in
addition to such information as the user ID and name.
[Operation Steps]
1.
When the photo taken by the FFR terminal is used, the photo can be displayed
upon successful verification.
2.
To use a photo stored in a USB disk, proceed as follows:
1) Create a folder with the name of “photo” in the USB disk, and store users'
photos under this folder.
2) The user photos must be in JPG format and named after their IDs. For
example, for the user with user ID of 154, the photo name must be
154.jpg.
3) Insert the USB disk into USB slot on the FFR terminal, and select USB
Disk Management -> Upload -> Upload Photos. Then user photos can be
displayed upon successful verification.
Note: 1) The length of a user name cannot exceed 24 digits.
- 71 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
2) The recommended size of a user photo is less than 30K.
4)
3) The uploaded new user photo will overwrite the existing photo in
related to the user ID.
To download user photos, select USB Disk Management -> Download ->
Download User Photos. A folder with the name of “photo” will be
automatically created on the USB disk, and all downloaded user photos
are stored under this folder.
- 72 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Appendix 5 Attendance Status Selection Function
Some FFR terminals also support the attendance status selection function which
requires users to select attendance status prior to verification. If verification is
performed without selection of the attendance status, the record is “No Work Status”,
that is, the record is not used as the attendance record, as shown in the following
figure:
You cannot set the timed status switch function on the FFR
terminal capable of attendance status selection.
- 73 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Appendix 6 Statement on Human Rights and Privacy
Dear Customers:
Thank you for choosing the hybrid biometric products designed and manufactured
by us. As a world-renowned provider of biometric technologies and services, we pay
much attention to the compliance with the laws related to human rights and privacy
in every country while constantly performing research and development.
We hereby make the following statements:
1.
All of our multibio recognition devices for civil use only collect the characteristic
points of multibio instead of the multibio images, and therefore no privacy issues
are involved.
2.
The characteristic points of multibio collected by our products cannot be used to
restore the original multibio images, and therefore no privacy issues are
involved.
3.
We, as the equipment provider, shall not be held legally accountable, directly or
indirectly, for any consequences arising due to the use of our products.
4.
For any dispute involving the human rights or privacy when using our products,
please contact your employer directly.
Our multibio products for police use or development tools support the collection of
the original multibio images. As for whether such a type of multibio collection
constitutes an infringement of your privacy, please contact the government or the
final equipment provider. We, as the original equipment manufacturer, shall not be
held legally accountable for any infringement arising thereof.
The law of the People’s Republic of China has the following regulations regarding
the personal freedom:
1.
Unlawful arrest, detention or search of citizens of the People's Republic of
China is prohibited; infringement of individual privacy is prohibited.
2.
The personal dignity of citizens of the People's Republic of China is inviolable.
3.
The home of citizens of the People's Republic of China is inviolable.
- 74 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
4.
The freedom and privacy of correspondence of citizens of the People's
Republic of China are protected by law.
At last we stress once again that biometrics, as an advanced recognition technology,
will be applied in a lot of sectors including e-commerce, banking, insurance and legal
affairs. Every year people around the globe suffer from great loss due to the
insecurity of passwords. The biometric products actually provide adequate
protection for your identity under a high security environment.
- 75 -
National World Systems. www.nwstm-us.com
Facial & Fingerprint Recognition Product Series User Manual 1.1.8
Appendix 7 Environment-Friendly Use Description
The Environment Friendly Use Period (EFUP) marked on this product refers to the
safety period of time in which the product is used under the conditions specified in
the product instructions without leakage of noxious and harmful substances.
The EFUP of this product does not cover the consumable parts that need to be
replaced on a regular basis such as batteries and so on. The EFUP of batteries is
5 years.
Names and Concentration of Toxic and Hazardous Substances or Elements
Parts Name
Toxic and Hazardous Substances or Elements
Pb
Hg
Cd
Cr6+
PBB
PBDE
Chip resistor
×
○
○
○
○
○
Chip capacitor
×
○
○
○
○
○
Chip inductor
×
○
○
○
○
○
Chip diode
×
○
○
○
○
○
ESD components
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adapter
×
○
○
○
○
○
Screws
○
○
○
×
○
○
○: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials for this part is above the limit requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with non-hazardous
environment-friendly materials. The hazardous substances or elements contained cannot be
replaced with environment-friendly materials at present due to technical or economical
constraints.
- 76 -
National World Systems. www.nwstm-us.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement