DX 120 Analog User Guide - Chesapeake Communications Inc.

DX 120 Analog User Guide - Chesapeake Communications Inc.
Analog Port Codes & Operation
User Guide
DX-120™ Analog Port Codes and Operation
Making a Call: Analog Ports (Single Line Telephones)
9
Outgoing Call (CO Line)
Dial CO Line code (other codes may be applicable).
Listen for CO Line dial tone; then dial the telephone number.
Intercom Call with Auto Selection Active
101–204
Go off-hook (CO dial tone heard)
Hook flash (listen for intercom dial tone)
Dial the extension
Intercom Call with Auto Selection Not Active
101–204
Listen for dial tone and dial the extension number.
Call Brokering (handling two calls)
{FLASH} + 2
While connected on a call press {FLASH} (hook-switch flash).
Dial CO Line code, wait for dial tone, and then dial second number.
To switch back to the first call, press {FLASH} then dial 2.
To disconnect the current call, press {FLASH} then dial 1.
Account Code
79
Dial 7 9 + valid account code, wait for dial tone.
0
Call Operator/Attendant
Dial 0.
Conference (3 party max.)
{FLASH} + 3
While on a call - press {FLASH} (hook-switch flash).
Make a second call.
Press {FLASH} (hook-switch flash), then dial 3.
Conference, Meet Me (4 party max.)
390 – 397
Operation – Transfer a caller to a Meet Me Conference
While connected to another extension or CO Line, momentarily press the
hook-switch (or press the FLASH button).
Wait for dial tone, then dial the Meet Me Conference (390-397).
Hang up to complete the transfer.
Operation – Join a Meet Me Conference
Dial the Meet Me Conference destination to join (390-397).
Last Number Redial
#8
Dial # 8.
DX-120 Analog Port Codes and Operation
2
Paging
400, 401 – 408, 777
Dial the Page access code (400-408, then 777).
Speed Dial
Extension 470–489,
System 500–699
Setup
Dial # , then 1, then 470-489 (speed # bin), input telephone #.
Press FLASH (hook-switch flash).
Operation – Use
Dial the Speed Dial bin (470-489, 500-699).
Alarm - Extension
#92
Operation – Activate
Dial #, then 9, then 2, hhmm (24hr format), then 1 for once, or 2 to have it
repeated daily.
Operation – Cancel
Dial the sequence: # * 9 2 .
Automatic Selection/Prime Line
Setting Auto Selection To a Specific Line
Go Off-Hook#951, 800-839
Dial the sequence # 9 5 1, then Line Directory Number (800-839)
Confirmation Tone Heard
Go On-Hook
Setting Auto Selection For a Specific Line Group
#951, 9 or 740–746
Go Off-Hook
Dial the sequence # 9 5 1 then Line Group Directory Number (9, or
740-746)
Confirmation Tone Heard
Go On-Hook
Cancelling Auto Selection
Go Off-Hook
Hook Flash (receive intercom dial tone)
Dial # 9 5 0-(confirmation tone heard)
Go On-Hook
DX-120 Analog Port Codes and Operation
#950
3
Call Forward - Extension
#2
Operation – Activate
Call Forward may be invoked for several operation modes. Each mode
may also be invoked: 1 = CO calls only, 2 = CO and Intercom calls,
3 = Intercom calls only.
Immediate Forward: dial # 2 2, (ext #), 1 / 2 / 3 option.
Busy Forward: dial #21, (ext #), 1 / 2 / 3 option.
No Answer Forward: dial # 2 4, (ext #), 1 / 2 / 3 option, t1, t2.
(t1 + t2 are time settings. t1 is - time the first call to your extension following
inactivity at your extension will ring before forwarding. t2 is the time all calls
after the first to your extension will ring before forwarding.)
Follow Me Forward: dial # 2 3, (your ext #), 1 / 2 / 3 option, your extension
password. (Calls to your extension will ring at this ext.)
Follow To Forward: Dial # 2 5, (ext #), 1 / 2 / 3 option.
Operation – Cancel Forward
Cancel Immediate Forward: dial # * 2 2.
Cancel Busy Forward: dial dial # * 2 1.
Cancel No Answer Forward: dial dial # * 2 4.
Cancel Follow Me Forward: dial dial # * 2 3.
Cancel Follow To Forward: dial dial # * 2 5.
Do Not Disturb
#4
Dial # 4. Repeat to clear.
Extension Password
#97
Dial # 9 7, password (0 0 0 0 - zeros set at factory), then input new
password.
Hotline
#9*
Operation – Setup
Dial # 9 *, ext # or speed bin #, 0–9 (0–9 seconds delay).
Whenever the telephone is taken off-hook, this destination is called.
Operation – Cancel
Lift the handset, momentarily press the hook switch (FLASH), then dial
# * 9 *.
Phone Lock/Unlock
#97
Dial # 9 7, extension password, then # for lock or * unlock.
Reset DND and Call Forward
#69*
Dial # 6 9 * and wait for the confirmation tone to cancel DND and Call
Forward modes.
DX-120 Analog Port Codes and Operation
4
Call Back - CO Line/Extension
#
When you try to access an outside line or extension and get a busy tone,
dial #.
Call Park Answer
#73
Dial # 7 3 + extension number where call is parked.
Call Pick Up
*, 440–447
Extension (Direct) Call Pickup:
Dial ringing extension number, 6.
Group Call Pickup:
Dial *.
Or…
Dial the group number of the ringing extension (440-447).
Camp On – Extension
4
When you call a busy extension, dial 4 and wait for them to answer.
Flash – CO Line
#3
While connected to a CO Line, momentarily press the hook switch
(FLASH), then dial # 3.
Forced Intercom Tone Ring
*
When you call an extension that is in Voice Announce mode and wish to
tone ring that extension, dial *.
Hold
{FLASH}
Place a call on hold:
While on a call, press {FLASH} (hook-switch flash).
Hang up. The line is placed on System (Common) hold.
Retrieve a call on hold:
Press {FLASH} (hook-switch flash).
Intrusion - Extension/CO Line
8
When you dial an extension that is busy, dial 8.
Meet Me Page
#59
While a page is currently in progress, dial #, then 59.
DX-120 Analog Port Codes and Operation
5
Messaging – Call Me
#96
Set:
When you have called an extension and wish to leave a message, press
# 9 6.
Cancel:
Dial # * 9 6,then the ext number of where your message was previously left.
Monitor - Extension/CO Line {Privacy Alert!}
1
When you dial an extension that is busy, dial 1. (Reference applicable laws
when using this feature.)
OHVA – Extension
0
When you call a busy extension, dial 0 and talk over their speaker.
Pulse to DTMF Conversion
*
After a Dial Pulse (rotary) call is made on a CO line, press *. Any digits
dialed following the * will be sent in DTMF (Tone) mode.
Tone Ring - Forced
*
When a digital speakerphone in Voice Announce mode is called, you can
change the alert to tone ring by pressing *.
Transfer
While connected on a call (CO Line or intercom extension), press {FLASH}
(hook switch flash).
Listen for dial tone, then dial the destination where this call is to be
transferred (extension, UCD Group, Virtual Number, etc.)
To screen the transfer, wait for the called extension to answer.
Hang up to complete the transfer.
DX-120 Analog Port Codes and Operation
6
This page intentionally left blank.
DX-120 Analog Port Codes and Operation
7
Copyright © 2006 Vertical Communications, Inc.
All rights reserved. Unauthorized use of this document is prohibited.
DX120L-AUG 0906
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement