BU-2015 User`s Guide
BU-2015
3-Megapixel Outdoor
IR NightVision
Bullet IP Camera
User’s Manual
Copyright and Disclaimer
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
This product contains some codes from GPL. In compliance with GPL agreement, AirLive
will publish the GPL codes on our website. Please go to www.airlive.com and go to the
"Support->GPL" menu to download source code.
All Trademarks are properties of their respective holders.
i
AirLive BU-2015 User’s Manual
Copyright and Disclaimer
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the A
user is encouraged to try to correct the interference by one of the following measures:
„ Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
„ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This device complies
with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. For
product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
This device and its antenna(s) must not be co-located or operation in conjunction with any
other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
WEEE Marking Warning:
The crossed out wheeled bin indicates the product must not be disposed together with
household waste. For the sake of the environment, the product should only be given to
entities involved in the reception of waste electronic and electrical equipment. The lists of
entities entitled to receive used equipment can be found on the websites of municipalities.
Some components of devices such as external wiring, circuit boards and liquid crystal
displays have a negative impact on the environment.
AirLive BU-2015 User’s Manual
ii
Table of Contents
Table of Contents
1. Overview .....................................................................................................1
1.1 Introduction ..........................................................................................1
1.2 Features...............................................................................................2
1.3 Product Specification ...........................................................................2
1.4 System Requirement ...........................................................................5
2. Package Contents and Installation...........................................................6
2.1 Package Content .................................................................................6
2.2 Connections .........................................................................................6
2.3 Install the Camera................................................................................8
2.4 Connect to IP Camera .........................................................................9
3. Using IP Camera via Web Browser.........................................................11
3.1 Windows Web Browser......................................................................11
4. Operating IP Camera via Mobile Phone .................................................12
4.1 Using IP Camera via iPhone..............................................................12
5. Operating the Network Camera ..............................................................15
5.1 Live View............................................................................................16
5.2 Configuration .....................................................................................17
6. Configuration ...........................................................................................18
6.1 System...............................................................................................18
6.2 Security..............................................................................................20
6.3 Network..............................................................................................21
6.4 IP Filter...............................................................................................24
6.5 Video..................................................................................................26
6.6 Motion ................................................................................................30
iii
AirLive BU-2015 User’s Manual
Table of Contents
6.7 Event..................................................................................................32
6.8 Recording ..........................................................................................37
6.9 SDHC.................................................................................................38
6.10 Log...................................................................................................40
6.11 Device info .......................................................................................41
6.12 Maintenance ....................................................................................41
AirLive BU-2015 User’s Manual
iv
1. Overview
1
1. Overview
This user’s manual explains how to operate this camera from a computer. Users should
read this manual completely and carefully before operate the device.
1.1 Introduction
AirLive BU-2015 is a high-level 3-Megapixel network camera which is designed for
professional outdoor surveillance and security applications. The built-in IR LEDs provides
high quality of night time monitoring with 15M viewing distance in darkness. Users are able
to view live video streaming over the Internet and also equipped with PoE function which
allows power and data to be transmitted via single Ethernet cable. This useful function
provides an easier installation, lower cabling costs and allows placement of AirLive PoE
cameras in locations without access to electrical source.
With the IP66 rated housing, AirLive BU-2015 offered water and dust proof features for
demanding environments. Also it can be easily installed and integrated into kinds of
surveillance project.
1
AirLive BU-2015 User’s Manual
1. Overview
1.2 Features
This manual will illustrate the steps of how to setup and operate this IP camera, so you’ll
soon be enjoying the benefits of these product features:
z
3-Megapixel 1/2.5” CMOS Sensor
z
Up to 20fps at 3MP resolution
z
Support H.264/MPEG4/MJPEG multi-streaming
z
Mechanical IR-Cut Filter Removable
z
22 units IR LED for 15M distance
z
Power over Ethernet (IEEE802.3af)
z
Compatible with ONVIF Standard
z
4mm High Quality Lens
z
Support Samba Server Function for Local Storage
z
Support Motion Detection and Email notification
z
MicroSD Card Support
z
IP66 Weatherproof Housing
z
Free Boundled 64-Channel Recording Software
Note: Please update FW to version 1.03.25 or above for 3MP resolution.
http://www.airlivesecurity.com/product/BU-2015/download
1.3 Product Specification
Model
Camera
Camera Type
Image Sensor
Max. Resolution
Lens Type
Night Vision
IR Distance (Max.)
Minimum Illumination
BU-2015
Outdoor IR Bullet Type
1/2.5" CMOS Sensor
2048 X 1536
4mm/F1.8, Board Lens
Yes
15M
Color: 0.05 Lux
B/W: 0 Lux (IR On)
Mechanical IR-Cut Filter
Yes
Auto Iris
Viewing Angle
Analog Video Out
None
H67.6°, V49.5°
None
AirLive BU-2015 User’s Manual
2
1. Overview
Video Compression
Resolution and Frame
Rate
Video
Streaming
Image Processing
Digital Zoom
Shutter Time
Ethernet
PoE
Network
Supported Protocols
Security
LED Indicator
General
Power LED
Link/Act. LED
Network Processor
Power Supply
3
H.264 High/Main/Baseline Profile, MPEG4
Simple Profile, MJPEG and 3GPP
20fps@2048x1536
30fps@1920x1080
30fps@1280x960
30fps@1280x720
30fps@720x480
30fps@640x480
30fps@320x240
Multi-profile streaming
Streaming over UDP, TCP, or HTTP
3GPP mobile view
Configurable frame rate and bandwidth
Support CBR and VBR
AE, AWB
Noise reduction
Brightness, Sharpness, Contrast,
Saturation
Mirror Vertical / Horizontal
Text, time and date OSD
Yes
Auto, Manual: 1/15~1/10000sec,
Day/night dual programmable
One RJ45 Port; IEEE 802.3u Compliant
10/100 Mbps Fast Ethernet with
Auto-MDIX
IEEE802.3af/at
TCP/IP, UDP, ICMP, DHCP, NTP, DNS,
DDNS, SMTP, FTP, HTTP, HTTPs,
Samba, PPPoE, UPnP, Bonjour, RTP,
RTSP and RTCP
Password protection
IP filter
HTTPS
Amber Color
Green Color
DSP Base
DC5V/2A (Optional)
AirLive BU-2015 User’s Manual
1. Overview
Power Consumption
8 Watts Max.
RJ-45 10BaseT/100BaseTX
Connector
5V DC power jack
Reset Button
Operation Temp: -20℃ ~ 50℃
Humidity: 20% ~ 85% non-condensing
Environment
Storage Temp: -20℃ ~ 60℃
Humidity: 0% ~ 90% non-condensing
Weather Proof
IP66
SD card slot
32G MicroSD/SDHC
Dimension
φ73mm x 112mm
CamPro Express 64, CamPro
Professional
Software
Search & Installation- IP Wizard II
Event Triggers
Motion detection
Motion Detection
Up to 3 zones
FTP or NAS file upload
Event handler
E-mail alter
UPNP
Yes
ONVIF
Application
Programming
System Integration
Open API for software integration
Interface
SDK
5 sec. pre-alarm / 5 sec. post-alarm, up to
Video Buffer
3MB
File upload via FTP, NAS, E-mail
Alarm Events
Notification via email
Save to SD card
Continuous Recording
Yes
Certificate
CE, FCC-Class A
OS
Browser
Cell Phone
Windows® XP, Vista, 7
IE 6.0 or later, Firefox 2.0 or later, Safari
With 3GPP player
VLC, Quick Time, Real Player, Core
Player
Viewing System
Video Player
Note: Please update FW to version 1.03.25 or above for 3MP resolution.
http://www.airlivesecurity.com/product/BU-2015/download
AirLive BU-2015 User’s Manual
4
1. Overview
1.4 System Requirement
For normal operation and viewing of the network camera, it’s recommended that your
system meets these minimum requirements for proper operation:
Item
CPU
VGA Monitor
RAM
Operating System
Web Browser
Cell Phone
Requirements
Pentium-4 3.6 GHz or higher
Resolution1280 x 1024 or higher
Minimum 1 GB of RAM
Window XP, Vista or Windows 7
Internet Explorer 7 or later; Apple Safari; Firefox; Google Chrome
3GPP Player
Note: Please keep updating the latest Windows software and service package.
(Ex: Net Framework, Windows Media Player, Enhance ActiveX Security)
5
AirLive BU-2015 User’s Manual
2. Package Contents and Installation
2
2. Package
Contents and
Installation
2.1 Package Content
User can find the following items in the package as below:
1. AirLive BU-2015 is the main element of the product.
2. Bundle CD includes IP Wizard II, CamPro Express64, Quick Start Guide, User Manual,
and Video clips.
3. Quick Start Guide provides important information and instructions for installing this
device.
4. Accessory Package including sunshield, bracket and screws.
Note: The power adapter is optional.
2.2 Connections
Power Source Requirement
This camera can work with 802.3af/at POE switch without the power adapter. However, if
you don’t have POE switch, you can use power adapter to provide power to camera.
Switch/Connector
There are various connectors of AirLive BU-2015 as shown in the figures below.
Please refer to the diagrams and tables accompanied with for using of each switch /
connector.
AirLive BU-2015 User’s Manual
6
2. Package Contents and Installation
1. RJ45 LAN socket: Connect to Hub / Switch / PoE Switch / PC.
This Ethernet port built N-Way protocol can detect or negotiate the transmission speed
of the network automatically. Please use Category 5 cable to connect the Network
Camera to a 100Mbps Fast Ethernet network switch or hub.
In the LAN socket, there are two LEDs embedded:
LAN LED (Green color)
Green Link Light indicates the network accessing.
Power (Amber color)
This LED is used to indicate whether DC power/PoE power is on or not.
2. DC-in: The input power is DC5V/2A.
7
AirLive BU-2015 User’s Manual
2. Package Contents and Installation
2.3 Install the Camera
Install the camera in LAN/WAN:
1.
Plug an Ethernet cable into the camera
Connect an Ethernet cable to the LAN socket and attach it into the network.
2.
Connect the external power supply to camera by power adapter or PoE switch.
3.
Remove the front cover to adjust the focus and insert the MicroSD card if necessary.
4.
Find the screws in the package to fix the sun shield on top.
AirLive BU-2015 User’s Manual
8
2. Package Contents and Installation
2.4 Connect to IP Camera
1. Insert the bundled CD into your PC/Laptop.
2. Auto Run screen pops up, click “Install Software Æ AirLive IP Wizard II” to install the
configuration tool.
9
AirLive BU-2015 User’s Manual
2. Package Contents and Installation
3. After completing installation, run the “Air Live IP Wizard II” to start to search the IP
camera.
4. The entire detected IP camera will be listed out.
5. If the Camera’s IP address is in the same IP segment as your LAN, select the founded IP
Camera and double click on the item. Then, the default browser will show up and connect
to the IP camera’s Web automatically.
AirLive BU-2015 User’s Manual
10
3. Using IP Camera via Web Browser
3
3. Using
IP Camera via
Web Browser
3.1 Windows Web Browser
1. Open your web browser and enter the IP address or host name of the IP camera in the
Location / Address field of your browser.
2. Use the default account “admin” and default password “airlive”.
Note: The default user name “admin” and the password “airlive” are the default values.
You can change them in the Security Menu. (Please check “Configuration → Security”)
11
AirLive BU-2015 User’s Manual
4. Operating IP Camera via Mobile Phone
4
4. Operating
IP Camera
via Mobile Phone
4.1 Using IP Camera via iPhone
You can access to your IP camera via your iPhone. Please follow the setting process below.
Then you can see the live view via iPhone.
2. Execute AirLive CamPro Mobile
1. Download AirLive CamPro
Mobile from APP store
3. Click Setup button.
AirLive BU-2015 User’s Manual
4. Setup page appears
12
4. Operating IP Camera via Mobile Phone
5. Click Add button.
6. Click LAN button and select the camera.
13
AirLive BU-2015 User’s Manual
4. Operating IP Camera via Mobile Phone
8. Key-in Username and Password
then click OK button.
7. Model, Address, HTTP Port info
appear on the page.
10. The video appears on the main screen.
9. Click Live View button.
Note: The image is continuous snapshots, not video. Thus, live image can’t be
recorded here.
AirLive BU-2015 User’s Manual
14
5. Operating the Network Camera
5
5. Operating
the
Network Camera
Start-up screen will be shown as follow no matter an ordinary users or an administrator.
In the left side, you can control Live View in your main Browser. Please refer to the
description below:
15
AirLive BU-2015 User’s Manual
5. Operating the Network Camera
5.1 Live View
1. Language
BU-2015 support multi-language, please choose from the pull-down list.
2. Stream
The device supports multi-profile function for H.264, MEPG4 and JPEG simultaneously.
User can choose the proper and/or preferred profile which is listed here.
3. Protocol
A user can select proper streaming protocol according to network environment.
4. Original size
/ Preview Size
Switches live image view between original size (Depends on main stream setting) and
preview size (smaller size).
5. Digital Zoom
You can see larger objects in video.
Please note: that digital zoom uses computer algorithm to enlarge the video and may
lose some details.
6. Snapshot
Take a snapshot and save images into your computer.
7.
Record
Press Record button to start recording. The video file is saved as ASF format into
your local PC. While you want to stop it, press Stop to stop recording.
8. Recording Location
Select the path to save the recording file.
AirLive BU-2015 User’s Manual
16
5. Operating the Network Camera
5.2 Configuration
Click “Configuration” for the camera detail settings. For more information, please refer to
Chapter 6.
17
AirLive BU-2015 User’s Manual
6. Configuration
6
6. Configuration
Click the “Configuration” to display sub-menus included:
System / Security / Network / IP Filter / Video / Motion / Event / Recording / SDHC /
Log / Device info / Maintenance
6.1 System
In this menu, you can configure basic IP camera settings here.
1. System
- Host Name
You can enter the name of this unit here. It’s very useful to identify the specific device
from multiple units. The information will be shown on IP Wizard II once the device is
been found.
- Indicator LED
Turn on or off the Indicator LED.
AirLive BU-2015 User’s Manual
18
6. Configuration
2. Date and Time
- Time Zone
Set the time difference from Greenwich Mean Time in the area where the device is
installed.
- Daylight Saving
Disable or enable the daylight saving.
- Keep the current date and time:
Select this option and the date / time setting will not be changed. You can refer to
“Camera Date and Time” item in this page for information.
- Synchronize with computer time
Click this option to enable time synchronization with PC.
- Synchronize with NTP Server
Click this option if you want to synchronize the device with NTP server (Network Time
Protocol).
- Set Manually
Click this option to set time and date manually.
When you finish with above settings, click ‘Apply’ button to save the changes
19
AirLive BU-2015 User’s Manual
6. Configuration
6.2 Security
In this menu, there are three kinds of account that you can configure.
- Administrator
An administrator has highest authority to view and configure all the settings.
For the first time use, input the default value below:
User Name: admin
Password: airlive
- User
User can view IP camera’s video and see settings, but can’t make any change.
- Guest
A guest can view IP camera’s video only.
There can be multiple users, but only one administrator is allowed, and you can’t change
administrator’s user name (it will always be ‘administrator’).
Item
Password /
Retype Password
(Administrator)
Account List
User Name
Password /
Retype Password
Authority
Description
Input the new password in both ‘Password’ and ‘Retype Password’
field, and click ‘Modify’ to apply the change.
Please note: You’ll need to reset IP camera’s all settings to get
default password once you forgot the new password.
Here will list out all existed users. Click ‘Remove’ button to remove
any account.
Note: If no user is existed, ‘New Account’ message will be shown
here.
Input new user’s username here. User name must be greater than 1
character and less than 32 characters.
Input this user’s password in both ‘Password’ and ‘Retype Password’
field.
To define the access privilege, select ‘User’ or ‘Guest’ in the
dropdown menu.
When you finish new user’s information, click ‘New’ button to create a
new user.
AirLive BU-2015 User’s Manual
20
6. Configuration
6.3 Network
1. General
Here are the descriptions of every setup item:
z
LAN:
Select this option to assign an IP address to LAN port (or obtain an address from
DHCP server automatically).
Available options are:
- DHCP IPv4: Obtain an IPv4 IP address from DHCP server on LAN automatically.
- DHCP IPv4 / IPv6: Obtain both IPv4 and IPv6 address from DHCP server on LAN
automatically.
- Static IPv4 / IPv6: Assign an IPv4 / IPv6 address to IP camera manually. If you don’t
have a DHCP server on your local area network, you must use this option to specify
an IP address.
- IP Address (IPv4): Input IPv4 IP address*
- IP Address (IPv6): Input IPv6 IP address*
- Prefix Length: Input IPv6 IP address’ prefix length (0­128)
21
AirLive BU-2015 User’s Manual
6. Configuration
- Subnet Mask: Input subnet mask
- Gateway: Input gateway address
- Primary DNS: Input DNS server’s IP address
- Secondary DNS: Input backup DNS server’s IP address, you can leave this field
blank.
* You can leave this field blank, if you only wish to use IPv4 or IPv6 IP address.
Enable UPnP Discovery: Check this box to enable other devices on network to
discover the presence of this IP camera by UPnP. It’s recommended to enable this
function.
Enable UPnP Port Mapping: When UPnP is enabled, check this box to enable UPnP’s
port mapping.
IP Address
(IPv4/IPv6)
Enter the IP address of the camera. The default setting is
192.168.1.100.
Subnet Mask
Enter the Subnet Mask of the camera. The default setting is
255.255.255.0.
Default Gateway
Enter the Default Gateway of the camera. The default
setting is 192.168.1.254
Primary/
Secondary DNS
DNS (Domain Name System) translates domain names into
IP addresses. Enter the Primary DNS and Secondary DNS
that are provided by ISP.
z
PPPoE:
Select this option to use PPPoE to connect to network. You have to input PPPoE
username and password assigned by network operator to get connected.
z
HTTP Port:
Input IP camera’s web connection port number here. When this port number is
changed, you need to change web browser’s port number you used to connect to IP
camera.
For example, if the IP camera’s IP address is 192.168.2.3 and you changed HTTP port
number to 82, please input ‘http: //192.168.2.3:82’ in web browser’s address bar to
access IP camera’s web configuration interface.
z
RTSP Port:
Input RTSP port number. When this port number changes, you must change
corresponding settings in external network devices (NVR or CMS software) so they
can receive this IP camera’s video.
AirLive BU-2015 User’s Manual
22
6. Configuration
z
RTP Data Port:
Input RTP data port number here.
When you finish with above settings, click ‘Apply’ button to save changes.
2. Advanced
You can setup advanced network settings in this page. This page is intended for
advanced settings only, and this IP camera will work fine even you don’t make any
changes to this page.
z
Multicast:
Enable video multicast:
Multicast Group Address: Input multicast group address here, must be an address
between 232.0.0.0 to 232.255.255.255.
Multicast video port: Input port number for video multicast here.
Multicast RCTP video port: Input port number for RCTP video here.
Multicast audio port: Input port number for audio here.
Multicast RCTP audio port: Input port number for RCTP audio here.
Multicast TTL: Input TTL value for multicast here.
z
Bonjour:
If you’re using Mac OS and you have Bonjour installed, you can use it to discover this
IP camera.
z
QoS:
Enable QoS to improve the data transfer priority of this IP camera (Your local area
network must support QoS).
You can select Video / Audio’s QoS DSCP value (0 to 63), or both video and audio.
z
DDNS:
Enable DDNS support if your ISP assigns dynamic IP address to you. You must
register a dynamic IP service first. Currently this IP camera supports Dyndns and
TZO dynamic IP service.
Provider: Select dynamic IP service provider.
Host Name: Input the host name you obtained from dynamic IP service provider.
User name: Input user name used to login dynamic IP service provider.
Password: Input the password used to login dynamic IP service provider.
z
DIPS ID:
It’s a unique number of each device for identification and this ID is used for DIPS. This
function now is reserved for future use.
23
AirLive BU-2015 User’s Manual
6. Configuration
z
HTTPS:
Check ‘Enable HTTPS’ box to enable HTTPS channel to encrypt transferred data.
You can also define HTTPS port number in ‘HTTPS Port’ field if you don’t want to use
default value ‘443’.
6.4 IP Filter
When this IP camera is directly connected to Internet and not protected by firewall, this
function acts like a mini built in firewall to protect the safety of this IP camera and avoid
attacks from hackers.
Item
Enable Filter
Accepted IP list
IP Address
(Accepted IP list)
Description
Check this box to enable IP address filter, uncheck this box to disable
this function.
Here lists all IP address that can build connections to this IP camera.
If you want to remove a set of IP address from the list, click on the IP
address and click ‘Remove’ button.
Input the starting and ending IP address of IP address you wish to
accept connections here. IP camera will only accept connections
established from these IP address.
AirLive BU-2015 User’s Manual
24
6. Configuration
Deny IP list
IP Address
(Accepted IP list)
If you want to specify one IP address only, input the same IP address
in both field.
Click ‘New’ button to add IP address into accepted IP list.
Here lists all IP address that cannot build connections to this IP
camera. If you want to remove a set of IP address from the list, click
on the IP address and click ‘Remove’ button.
Input the starting and ending IP address of IP address you wish to
deny connections here. IP camera will deny connections established
from these IP address.
If you want to specify one IP address only, input the same IP address
in both field.
Click ‘New’ button to add IP address into deny IP list.
When you finish with above settings, click ‘Apply’ button to save changes.
25
AirLive BU-2015 User’s Manual
6. Configuration
6.5 Video
1. Image Setting
You can adjust the image parameters in this page.
z
Brightness /Contrast /Saturation /Sharpness:
Control the image parameters. Click ‘­‘ to decrease value, or click ‘ + ‘ to increase
value. You can also input the value in the field directly.
z
Exposure Setting:
1. Manual: You can setup more details here including Exposure Value, Exposure Time
and Gain.
2. Exposure Value is from 0~255
3. Exposure Time range is about Auto, 1/15, 1/30, 1/50, 1/60, 1/100, 1/120, 1/250,
1/500, 1/1000, 1/2000, 1/4000, 1/10000.
4. Gain value is from 0~8
5. Auto: Camera will adjust the exposure automatically.
z
Mirror:
Check “Vertical” and “Horizontal” box to flip the image vertically or horizontally.
z
Power Line Frequency:
Select the frequency of power line of the place you’re using this IP camera.
help to reduce the flicker of certain lights in the image.
This will
z
Condition(AWB):
Select the condition that you’ll be using this IP camera from dropdown menu.
Auto: IP camera will adjust its parameters automatically.
Indoor, B/W, Tungsten: IP camera will adjust its parameters by different environment.
z
IR cut:
An IR cut filter is built in this IP camera to reduce the effect of IR lights (which will
change the color of image and makes it looks different than what you see through your
eyes), and most of IR lights are coming from sunlight.
You can select the behavior or IR cut filter:
Auto: IR filter will act automatically. If you don't know wheatear you should use IR
filter or not, select this option.
Night mode (B/W): IR filter is always on.
Day mode (Color): IR filter is always off.
AirLive BU-2015 User’s Manual
26
6. Configuration
z
Day:
Select the time that you want to keep the day mode.
2. Video Setting
You can adjust the video transfer parameters in this page.
Here are the descriptions of every setup item:
Item
Description
H.264 /MPEG4
Select the compression of main stream: H.264 / MPEG4.
Video Resolution Select video resolution.
‐ H.264:
2048x1536 (3MP) /1920x1080 (1080p) / 1280x960 (960p) /
1280x720 (720p) / 720x480 (D1) / 640x480 (VGA) / 320x240
(QVGA)
‐ MPEG4:
1920x1080 (1080p) / 1280x960 (960p) / 1280x720 (720p)
720x480 (D1) / 640x480 (VGA) / 320x240 (QVGA)
‐ MJPEG:
720x480 (D1) / 640x480 (VGA) / 320x240 (QVGA)
Frame Rate
Select video frame rate.
When network speed is insufficient, select a lower frame rate will help.
27
AirLive BU-2015 User’s Manual
6. Configuration
Rate Control
Mobile View
Select video bit rate. You can control bit rate by both ‘Video quality’ and
‘Bitrate’:
‐ Video quality: There are 5 levels of video quality, select ‘very high’
to improve video quality but consumes more network bandwidth,
and select ‘very low’ will decrease video quality and consumes less
network bandwidth.
‐ Bitrate: Input video’s bit rate directly. It must an integer between
512 and 6000. Higher bit rate provides better video quality, but
consumes more network bandwidth.
Checking the radio box to enable remote access when you need to
remote access via mobile phone.
Note: Please update FW to version 1.03.25 or above for 3MP resolution.
http://www.airlivesecurity.com/product/BU-2015/download
When you finish with above settings, click ‘Apply’ button to save changes.
AirLive BU-2015 User’s Manual
28
6. Configuration
3. Overlay
You can adjust the video overlay parameters in this page.
Here are the descriptions of every setup item:
Item
Enable Time
Stamp
Remove the
background color
of the text
(for Time Stamp)
Enable Text
Display
Remove the
background color
of the text (Text)
Enable Image
Overlay
Description
Check this box to enable overlaying time stamp on video.
Check this box to remove time stamp’s background color. You may
find this will help the readability of time stamp text in some cases.
Check this box to display certain text on video; this will help when
you need to identify certain IP camera when you have a lot of IP
cameras.
Please input the text in ‘Text’ field. You can input up to 15 characters.
Check this box to remove custom text’s background color. You may
find this will help the readability of text in some cases.
Check this box to overlay a specific image on video, so you can
show certain text / picture on the video and help people to identify
this IP camera.
Click ‘Browse’ button to pick a picture on your computer, then click
‘Update’ button to use the picture. Please note that there are certain
restrictions:
‐ Select .bmp / .jpg / .jpeg image files only.
‐ Image’s resolution should be less than 160 x 128, and can be
divided by 4.
‐ Do not upload image files that size is greater than 64KB.
When you finish with above settings, click ‘Apply’ button to save changes.
29
AirLive BU-2015 User’s Manual
6. Configuration
6.6 Motion
This IP camera is capable to detect object’s motion, so IP camera will only record when
there’s motion and save disk storage space.
Motion detection is performed by examine the movement of objects in rectangular motion
detection area. You can define up to 3 motion detection areas.
Here are the descriptions of every setup item:
Item
Description
Enable Motion
Check this box to enable motion detection.
Detection
Enable
Check this box to enable this motion detection window. You can select
(Window 1 to
window 1 to 3 to enable up to 3 motion detection windows. When a
Window 3)
motion detection window is enabled, a rectangular will appear on
camera’s view, with its title on the top. And you can move / resize the
detection window.
AirLive BU-2015 User’s Manual
30
6. Configuration
Title
(Window 1 to
Window 3)
Percentage
Sensitivity
Input characters in title field to change motion detection area’s title
text so you can identify it.
Please note that you have to click ‘Apply’ button and the text will
change.
Select the percentage of pixel change that will trigger motion detection
alert. Select a lower percentage so you can detect tiny changes in
motion detection area.
Select the sensitivity level that will trigger motion detection alert.
Select a higher sensitivity so you can detect tiny changes in motion
detection area. It will show blue bar when window are detecting
moving object through the window range.
When you finish with above settings, click ‘Apply’ button to save changes. Once the
window detects motion, one blue flexible bar will appear at the bottom edge. One video
file will be saving at this moment if the ftp server was enabled.
31
AirLive BU-2015 User’s Manual
6. Configuration
6.7 Event
When there’s an event, you can use this setup page to define what IP camera should do,
like send an Email or trigger digital output to activate external alarm.
There are three setup pages:
1.
2.
3.
Setting: Define a new event and manage events.
Media: Define what kind of media file should be saved on designate media.
Event Server: Define the details of remote server.
Please refer to following chapters for detailed instructions.
1. Setting
This page lists all existing events. You can click ‘Modify’ button to edit an existing event,
or ‘Remove’ to delete an existing event.
To create a new event, just click “New” button to add an Event setting.
Item
Enable Setting
Title
Motion
Detection
Enable
Schedule Time
Enable FTP
Enable EMAIL
Description
Check this box to enable this event. If you just want to disable this
event temporarily, you can uncheck this box to keep this event and
disabling while not deleting it.
Input any description text for this event so you can identify it quickly.
You can use alphabets, numbers, and symbols include:!$-.@^_~ (no
spaces allowed).
Check this box and this event will be activated when one of motion
detection window detects motion.
Check this box and this event will be activated when designated
weekday and time is reached.
You also have to check weekday box, and select time from dropdown
list. If you select ‘Always’ as time, this event will be activated during all
the day.
Check this box and IP camera will save file on FTP server (refer to ‘FTP
Server’ setting in ‘Event Server’ tab) when this event is activated.
Check this box and IP camera will send an Email to designated
recipient address (refer to ‘SMTP Server’ setting in ‘Event Server’ tab)
when this event is activated.
AirLive BU-2015 User’s Manual
32
6. Configuration
Enable Samba
(Net Storage)
Enable SD
CARD
Check this box and IP camera will save file on samba server (refer to
‘Samba Server’ setting in ‘Event Server’ tab) when this event is
activated.
Check this box and IP camera will save file on SD card when this event
is activated. A working SD card must be inserted into IP camera in
advance.
2. Media
Here are the descriptions of every setup item:
Item
Description
One Snapshot
Save a picture file when event is triggered.
Maximum Video Save a H.264 video clip. You can also select the recording length
File Size: 3MB
before and / or after the time when event is triggered in ‘Pre Event’ and
‘Post’ Event’.
For example, if you set ‘Pre Event’ to ‘10’ and ‘Post Event’ to 5’, and an
event is triggered at 14:10:30, then the video file will be 15 seconds
long, starting from 14:10:20 to 14:10:35.
33
AirLive BU-2015 User’s Manual
6. Configuration
Tips: You may want to know what happened before event is
triggered in many cases, especially when object is outside of
motion detection window.
Note: If the “Pre Event” set to “0” second, the “Post Event”
cannot set to “0” second.
When you finish with above settings, click ‘Apply’ button to save changes.
3. Event Server
You can define the details of remote media server: FTP (File), SMTP (Email), and Samba
(File).
A Samba server can be any computer running windows operating system with
network neighbor function enabled. Many stand-alone network file server also
support samba server function.
Here are the descriptions of every setup item:
Item
Description
Enable FTP
Check this box to enable FTP server upload.
Server
AirLive BU-2015 User’s Manual
34
6. Configuration
FTP Server: Input FTP server’s IP address or hostname.
Port: Input FTP server’s port number. In most cases it should be
default value ‘21’.
‐ User Name: Input FTP server’s username.
‐ Password: Input FTP server’s password.
‐ File Path Name: Input the path where you want to save file on FTP
server, like ‘upload/record’. If you want to save file on this FTP
user’s home directory, you can leave this field blank.
‐ Enable Passive Mode: Check this box to force IP camera to
communicate with FTP server in passive mode (Some FTP Server
may only work when you check this box, while others don’t).
‐ Test FTP: Click this button to test FTP server settings above
immediately.
Check this box to enable Email send.
‐
‐
SMTP Server
‐
‐
SMTP Server: Input SMTP server’s IP address or hostname.
Port: Input SMTP server’s port number. In most cases it should be
default value ‘25’.
35
AirLive BU-2015 User’s Manual
6. Configuration
Sender Email Address: Input the sender’s email address that will
appear in the Email send by IP camera. This will help you to
identify the Email sent by this IP camera, and may help when you
have anti-spam software installed (you can set this Email address
to ‘White List’ in your anti-spam software)
‐ Receiver #1 Email Address: Input primary recipient’s Email
address. This field is required.
‐ Receiver #2 Email Address: Input backup recipient’s Email
address. This field is optional.
‐ Subject: Input Email title that will appear in the Email send by IP
camera. This will help you to identify the Email sent by this IP
camera.
‐ Authentication: Check this box when authentication is required by
the Email server you’re using. You also need to input Email
server’s username and password in corresponding field.
‐ Requires SSL Encryption: If your Email server required SSL
encryption, check this box. Please note that some Email server
uses different port number than standard port 25 when SSL
encryption is used.
‐ STARTTLS: If your Email server required STARTTLS encryption,
check this box. Please note that some Email server uses different
port number than standard port 25 when STARTTLS encryption is
used.
‐ Test SMTP: Click this button to test SMTP server settings above
immediately.
Check this box to enable Samba server file upload.
‐
Samba Server
‐
‐
Samba Server Address: Input Samba server’s IP address or
hostname.
Path: Input the path where you want to save file on Samba server,
like ‘upload/record’. If you want to save file on this user’s home
directory, you can leave this field blank.
AirLive BU-2015 User’s Manual
36
6. Configuration
User Name: Input Samba server’s username.
Password: Input Samba server’s password.
Test SMB: Click this button to test Samba server settings above
immediately.
Tips: Some samba server does not have username and
password check, you can just input samba server address and
path to access the file storage space.
‐
‐
‐
When you finish with above settings, click ‘Apply’ button to save changes.
6.8 Recording
You can save video file in the Memory card or Samba server.
Note:
Be sure that the Micro-SD Card format should be FAT32.
cannot be supported by this camera.
The NTFS format
Here are the descriptions of every setup item:
Item
Description
Enable External
Check this box to enable this function.
storage Recording
Maximum Size of
Input the maximum size of every video file from 1MB to 50MB. IP
Each File
camera will start a new video file when a recording video file
reaches the size limit stated here.
Recording Schedule Define the recording schedule. You can check Sun to Sat boxes to
represent a weekday, and specify time period in ‘From’ and ‘To’
field. Select ‘Always’ to record 24 hours in selected weekday(s).
Storage Option
Select Memory card or Samba server as your destination.
When you finish with above settings, click ‘Apply’ button to save changes.
37
AirLive BU-2015 User’s Manual
6. Configuration
6.9 SDHC
1. Status
Once the Micro-SD card is inserted, the UI will show the information of the
Micro-SD card.
AirLive BU-2015 User’s Manual
38
6. Configuration
2. Recording
There are two UI pages to show the record on the Micro-SD card. They are
mapping to the setting of “Recording to Micro-SD card” and “Event”
accordingly.
Click “All file” to list all files. You also can define the range and click
“Search” to sort the files needed. It shows likes the images in the next
page.
3. Event
Set the time range then click “Search” then shows the records like below.
39
AirLive BU-2015 User’s Manual
6. Configuration
6.10 Log
You can check the log file of IP camera here.
In this page, you can click:
1. First page / Final page: Jump to first / final page of log.
2. Previous / Next: Jump to previous or next page of log.
3. Remove: Clear log. You’ll be prompted for confirmation.
AirLive BU-2015 User’s Manual
40
6. Configuration
6.11 Device info
You can check the information and network settings of this IP camera. This information is
very useful when you need to repair or fix the problem of this IP camera.
An example of device info page looks like this:
6.12 Maintenance
You can do some maintenance job about this IP camera here.
Here are the descriptions of every setup item:
Item
Reboot
Description
Click this button to reboot the IP camera. This function is useful when
the IP camera is not working properly.
41
AirLive BU-2015 User’s Manual
6. Configuration
Factory Reset
Backup
Backup to SD
card device
Restore
Restore from
SD card device
Upgrade
(1) Clear all settings of IP camera and reset to factory default setting.
(2) Reset all parameters, except for the IP, time zone and daylight
saving parameters to the original factory settings
Backup IP camera’s setting and save it on your computer.
Backup IP camera’s setting and save it on SD card. A SD card must be
inserted into SD card slot when you click this button, or you’ll receive
an error message.
Restore a previously-saved configuration file saved on your computer.
Click ‘Browse’ button to select a file on your computer first, then click
‘Restore’ button.
Restore IP camera’s configuration which is previously-saved on SD
card.
Upgrade IP camera’s firmware. Click ‘Browse’ button to select a
firmware image file on your computer first, then click ‘Upgrade’ button.
AirLive BU-2015 User’s Manual
42
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising