Retractable Ceiling Fans
Model No.: HY-8388-48B
Size: 48 inches
Please contact us with following information:
1. Screen shot of your order page, including product picture, name and order
ID number.
2. Problem details with pictures / short video if possbile.
1 Email: [email protected]
Packing List
①
②
③
④
⑤
⑥
⑧
⑦
⑨
⑩
Name QTY Name QTY
(1) Mounting Bracket 1 (6) Bulb Holder 1
(2) Canopy 1 (7) Threaded Tube Hub 1
(3) Downrod 2 (8) Light Frame 1
(4) Adapter Cover 1 (9) Remote Control 1
(5) Fan Motor Assembly 1 (10) Hardware Bag 1
Please open your package and check the accessories according to the packing list.
NOTE:
1. Light Frame ⑧ style may vary. Please check page 7 for details.
2. Downrod: short x 1pcs, long x 1pcs
3. Remote control requires AAA 1.5V battery x 2pcs (not included)
Email: [email protected] 2
Safety Rules
1. Be sure the power to the wires you are working on is disconnected, either the fuse is removed or the circuit breaker is turned off. Turning the power off using the light switch is not sufficient to prevent electrical shock.
2. A qualified licensed electrician is required for the installation.
3. The outlet box and support structure must be securely mounted and capable of reliably /supporting a minimum of 50 pounds. Use only UL (cUL for Canadian Installation) listed mounting boxes marked "FOR FAN SUPPORT".
4. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor.
5. Do not operate reversing switch while fan blades are in motion (if applicable). Fan must be turned off and blades stopped before reversing blade direction.
6. Do not place any objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened soft cloth will be suitable for the cleaning.
9. After marking electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor on one side of the outlet box.
10. Electrical diagrams are reference only, different fan light may have different light shade and bulbs.
11. Use only our replacement parts. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.
Warning:
To reduce the risk of personal injury, use only the two steel screws and washers provided with the outlet box for mounting to the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and need to be replaced, consult a qualified electrician if in doubt.
To reduce the risk of fire, electric shock or person injury, mount fan to outlet box marked "acceptable for fan support".
To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
3 Email: [email protected]
1. Installation Preparation
Tools You Need
Ladder Pliers Screwdrivers Power Drill
Strippers (optional)
If mounting to a support structure, you will also need the optional tools.
Drill Bit
(optional)
What to Expect with Your Installation
Must be able to secure the fan to building structure or fanrated outlet box
You may need a friend to help you.
30 inches from blade tip to nearest wall or obstruction
7 feet from bottom edge of blade to the floor
Assess location Check box to see fan weight
Ceiling angles greater than 22° will require an
Angled Mounting K it.
Assess ceiling angle
Mounting Options
Support
Structure
Short downrod
Outlet Box
(required)
Long downrod
Outlet Box
(required)
Use short downrod for flat and less than
9 feet ceiling.
Use long downrod for high or angled ceiling less than 22°.
NOTE: For longer downrod or angled ceiling greater than 22°, please contact us.
Email: [email protected] 4
2. Installing the Fan
Outlet box
NOTE: This ceiling fan is supplied with two types of hanging downrods:
1. The short downrod for "close-to and flat ceiling" installation (less than 9 feet).
2. The long downrod for high or angled ceiling less than 22°.
3. Please contact us if you need longer downrod or angled ceiling greater than 22°.
Mounting bracket
Hook
Power Wire
Flat washer
Mounting screw
(supplied with the outlet box)
Fig. 5
1. Installing the Bracket
Step 1. Pass the power wires through the center hole in the mounting bracket as shown in Fig. 5.
Step 2. Secure the mounting bracket to the ceiling outlet box with the screws and washers provided with your outlet box.
Downrod
Adapter cover
2. Assembling the Fan
Step 1. Assemble the canopy and adapter cover as Fig. 6.
Step 2. Remove the the bolt, pin and set screws from the top of the fan motor assembly.
Step 3. Route wires from the top of the fan motor through downrod/ ball.
Step 4. Align the holes at the bottom of the downrod with the holes in the collar on top of the motor housing (Fig. 6). Carefully insert the bolt through the holes in the collar and downrod. Be careful not to jam the bolt against the wires inside the downrod. Insert the pin to the end of the bolt
(Fig. 6).
Step 5. Fix the downrod with set screws provided.
Fig. 6
Canopy
Set screw
Bolt Pin
3. Hanging the Fan
Place the downrod ball into the bracket socket
(Fig. 7). Be sure the fixation slot is locked by the bracket.
Fixation slot
Fig. 7
5 Email: [email protected]
the bolt
(Fig. 6).
Step 5. Fix the downrod with set screws provided.
3. Hanging the Fan
Place the downrod ball into the bracket socket
(Fig. 7). Be sure the fixation slot is locked by the bracket.
3. Wiring
House Wires
Fan Wires
Fig. 8
Outlet box
NOTE: THIS FAN ONLY NEEDS ONE
SET OF INPUT WIRES
(black, white and ground wire). Both of the fan and lights will be controlled by the remote controller. The wall switch is not able to control the fixture full functionally.
THIS FAN CAN ONLY BE
CONNECTED ONTO ON/OFF SWITCH
IF YOU HAVE ONE, NOT SUITABLE
FOR DIMMAER SWITCH.
Step 1.
Connect the fan live wire (black) to your house live wire (black).
Step 2.
Connect the fan neutral wire
(white) to your house neutral wire (white).
Step 3.
Connect the fan ground wire
(from downrod, green
&
yellow stripe / green / bare copper) to your house ground wire (optional).
Step 4.
After connecting the wires, spread them apart so that the live wires are on one side of the outlet box and the neutral wires are on the other side.
4. Attaching the Canopy
Outlet box
Mounting bracket
Screw Screw
Canopy
Step 1.
Insert the wires and wire connectors into the outlet box.
Step 2.
Slide the canopy upto the ceiling and attach it to the mounting bracket with the screws provided. Tighten all screws securely.
Fig. 9
Email: [email protected] 6
5. Installing Bulb and Light Shade
Step 1. Screw the bulb holder hub onto the center of fan base. Pass the wires through the side hole.
Step 2. Take off the threaded tube from the bulb holder, screw it into the hub and fix it with a screw. Connect the wires from the bulb holder to the ones from the fan.
14.5cm
Step 3. Fix the bulb holder onto the threaded tube with cap nut on it. Install bulbs (E26/E27 Max. 60W each). NOTE:
For 48" fan, bulb length should be no more than 5.7 inch/ 14.5cm.
Step 4. Take off screws from the base, attach the frame onto the base with screws taken off.
NOTE: This fan light is not dimmable, it can not be dimmed even with dimmable bulbs.
7 Email: [email protected]
Remote Control Instructions
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
⑭
⑮
NOTE:
Please insert 2 batteries before using.
AAA 1.5V battery x 2pcs (not included)
① : Turn off the fan and lights.
②⑦ : "F" refers forward fan direction."R" refers reverse the fan.
③④⑨⑩ ⑫⑬
: 1/2/3/4/5/6 for fan speeds.
⑤ ⑭⑮
: 1H/2H/4H for timing the fan.
⑥ : Turn on/off the lights.
⑧ : Natural wind of the fan, fan speed will change automatically when use this function.
⑪
: Turn off the fan.
Email: [email protected] 8
Trouble Shooting
1. Fan doesn't work
• Press a fan speed button (1-3).
• Check the remote control battery (not included in this package).
• Check the circuit breaker to ensure the power is turned on.
• Make sure the blades spin freely.
• Turn o ff
power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.
2. Bulbs do not light up
• Check your power and switch to make sure it's power on.
• Check the bulb to make sure it's installed correctly
• Change a new bulb.
• Check the wires to make sure they are connected correctly.
4. Noisy operation
• Tighten the light fi tting
• Re-tighten all screws on bracket, downrod and fan blades (do not over tighten)
• Check to see if any of the blades are cracked. If so, replace all of the blades.
5. Remote does not work
• Make sure the battery is installed correctly.
• Install 2 new batteries.
6. Excessive wobbling
• Tighten all of the blade screws.
• Turn off power, support the fan carefully, and check that the hanger ball is properly seated.
• Use the provided balancing kit and instructions to balance the fan:
Step 1.
Attach the magnet to place ① , ② , ③ or ④ , turn on the fan and test where it needs the balance kit.
Step 2.
Replace the magnet with the balance paster.
Magnet
Balance paster
9 Email: [email protected]
Clean And Care
To clean, wipe fi xture with soft cloth. Spray from chemical cleaners can discolor the fi nish of fi xture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fi xture.
Ordering Parts
Keep this manual for future reference, and in case replacement parts are needed.
Available parts can be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
Hazardous substance
Email: [email protected] 10
"We followed the light to a brighter
and warmer place."
