Installation Instructions
Kinetix 5700 System Mounting Toolkit
Catalog Number 2198-K5700-MOUNTKIT
About the System Mounting
Toolkit
The Kinetix® 5700 system mounting toolkit is used to locate the drill-holes for
your Kinetix 5700 drive system. Properly spaced drill-holes are essential for
engaging the zero-stack tab and cutout from module-to-module so that the
DC-bus connectors are spaced properly to accept the DC-bus links. The
Kinetix 5700 system mounting toolkit includes the drill-hole guide and
mounting bar. Two M4 thread-forming fasteners are also included.
See the Kinetix 5700 Servo Drives User Manual, publication 2198-UM002, for
detailed information on wiring, applying power, troubleshooting, and integration
with Logix5000™ controllers.
Install the Mounting Bar and
Position the Drill-hole Guide
The mounting bar must be mounted horizontally on the system panel. The
drill-hole guide inserts behind the mounting bar and slides left and right. Holes
and slots in the drill-hole guide let you establish the location of each
Kinetix 5700 drive module.
Figure 1 - Mounting Bar
100
M4 thread-forming
fasteners, 1.7 N•m (15 lb•in)
100
Dimensions are in mm (in.)
Drill-hole Guide
Mounting Bar
3x Ø4.50 (0.18)
43.2 (1.70) Ref
10 (0.39)
2x 10 (0.39)
2x 190 (7.48)
400 (15.75)
Follow these steps to locate the drill-holes for your Kinetix 5700 drive system.
1. Draw a horizontal line on the panel where you would like to position the
upper module-width holes (refer to Figure 2).
2. Drill three 3.6 mm (0.14 in.) holes 506 mm (19.9 in.) below the line you
drew in step 1 for attaching the mounting bar to the panel.
3. Attach the mounting bar to the panel by using the two M4 fasteners.
2 Kinetix 5700 System Mounting Toolkit
4. Determine (left to right) the leftmost module position and draw a vertical
line where you would like the center of that leftmost module.
Center of Leftmost Module
Horizontal Line Drawn on Panel
55
85
100
85
100
5. Slide the drill-hole guide into the mounting bar and adjust left-to-right
until the 55 mm upper module-width hole is aligned with the vertical line
you drew in step 4.
6. Mark the upper and lower module-width holes appropriate for the
drive-width of module being mounted.
In this example, the leftmost module is 85 mm wide.
Center of Leftmost Module
Horizontal Line Drawn on Panel
55
85
100
85
100
100
85
100
85
55
55
Right-side Alignment Slot
55
EXT MODULE
7. Draw a line along the left edge of the right-side alignment slot appropriate
for the drive-width of module being mounted.
8. Slide the drill-hole guide to the right until the line you drew in step 7 is just
visible in the left-side alignment slot appropriate for the drive-width of
next module being mounted.
Center of Leftmost Module
Horizontal Line Drawn on the Panel
55
Drill-holes Marked in Step 6
85
100
85
100
100
85
100
85
55
55
Left-side Alignment Slot
55
EXT MODULE
In this example, the next module is also 85 mm wide.
9. Repeat step 6 through step 8 for each module in your drive system.
Rockwell Automation Publication 2198-IN012A-EN-P - March 2015
Kinetix 5700 System Mounting Toolkit 3
TIP
When drive systems are wider than the mounting bar, you can remove the
screws and shift the mounting bar left or right, reusing two of the original
holes and drilling another (repeat as needed).
10. Remove the mounting bar from the panel when you are finished.
Figure 2 - Kinetix 5700 System Mounting Toolkit
Upper Module-width Holes
55
85
100
85
100
55
85
Left-side Alignment Slots
Right-side
Alignment Slot
100
85
100
Reference Lines
55
55
Right-side Alignment Slots
55
EXT MODULE
Always draw your lines in the
slot on the side marked with
the reference lines.
Extension Module Lower Hole
55
Module-width holes are
55, 85, and 100 mm
55
Left-side
Alignment Slot
506 mm
(19.9 in.)
Left-side alignment slot moved
right to align with line drawn in
the right-side alignment slot.
Lower Module-width Holes
85
100
85
100
Mounting Bar
Rockwell Automation Publication 2198-IN012A-EN-P - March 2015
For More Information
These documents contain information concerning related products from
Rockwell Automation.
Resource
Description
Kinetix 5700 Servo Drives User Manual, publication 2198-UM002
Provides information on installing, configuring, start up, and troubleshooting your Kinetix 5700
servo drive system.
Kinetix Motion Control Selection Guide, publication GMC-SG001
Overview of Kinetix servo drives, motors, actuators, and motion accessories designed to help make
initial decisions for the motion control products best suited for your system requirements.
Kinetix 5700 Drive Systems Design Guide, publication GMC-RM010
System design guide to select the required (drive specific) drive module, power accessory, feedback
connector kit, and motor cable catalog numbers for your Kinetix 5700 drive and Kinetix VP motor
motion control system.
Kinetix Servo Drives Specifications Technical Data, publication GMC-TD003
Product specifications for Kinetix Integrated Motion over the EtherNet/IP network, Integrated
Motion over sercos interface, EtherNet/IP networking, and component servo drive families.
Rockwell Automation Industrial Automation Glossary, publication AG-7.1
A glossary of industrial automation terms and abbreviations.
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Allen-Bradley, Kinetix, Logix5000, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Publication 2198-IN012A-EN-P - March 2015
Copyright © 2015 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
">
