CE TEST REPORT

CE TEST REPORT
CE TEST REPORT
(LVD)
Application No.
Report No.
CE-002-07CQC0025L
Name of product:
Model:
CE2007CQC0904-002148
Cutting plotter
SB-60
Trade Mark:
Applicant:
--
Great Computer (Kunshan) Co., Ltd.
CHINA QUALITY CERTIFICATION CENTER
Test Report issued under the responsibility of:
TEST REPORT
IEC 60950-1: 2005 (2nd Edition) and/or EN 60950-1:2006
Information technology equipment – Safety –
Part 1: General requirements
Report Reference No. ....................:
CE-002-07CQC0025L
Date of issue ....................................:
Dec.12,2007
Total number of pages ......................
48 pages
CB/CCA Testing Laboratory..........:
TIRT of CTIEP/IECEE-CB-LABORATORY
Address ............................................:
Yi 7 Jiuxianqiaobei Road , Chaoyang District , Beijing , P. R. China
Applicant’s name............................:
Great Computer (Kunshan) Co.,Ltd.
Address ............................................:
No.1, Chen Feng Road, Yushan, Kunshan, Jiangsu.China
Manufacturer’s name .....................:
Great Computer (Kunshan) Co.,Ltd.
Address ............................................:
No.1, Chen Feng Road, Yushan, Kunshan, Jiangsu.China
Factory’s name ...............................:
Great Computer (Kunshan) Co.,Ltd.
Address ............................................:
No.1, Chen Feng Road, Yushan, Kunshan, Jiangsu.China
Test specification:
Standard...........................................:
IEC 60950-1:2005 (2nd Edition) and/or
EN 60950-1:2006
Test procedure .................................:
CB / CCA
Non-standard test method…………..:
N/A
Test Report Form No. ....................:
IECEN60950_1C
Test Report Form(s) Originator ........:
SGS Fimko Ltd
Master TRF ......................................:
Dated 2007-01
Copyright © 2006 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme
procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended
to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
If this Test Report Form is used by non-CCA members, the CIG logo and the reference to the CCA Procedure shall be
removed.
This report is not valid as a CCA Test Report unless signed by an approved CCA Testing Laboratory and
appended to a CCA Test Certificate issued by an NCB in accordance with CCA
Test item description .....................:
Cutting Plotter
Trade Mark ....................................... :
/
Manufacturer .................................... :
Great Computer (Kunshan) Co.,Ltd.
Model/Type reference ...................... :
SB-60
Ratings ............................................. :
100-240VAC 50/60Hz MAX.1.2A
Page2 of 48
ReportNo.CE-002-07CQC00251
Testing procedureand testing location:
CB/CCATestingLaboratory:
X
Testinglocation/
address
AssociatedGB Laboratory:
I
Testinglocation/
address
Testedby (name+ signature).
APProved
bY(* signature)
tr
TMP
Testingprocedure:
Testedby (name+ signature)
A p p r o v e db y ( * s i g n a t u r e. ). . . .
Testinglocation/
address
f
Testingprocedure:
WMT
Testedby (name+ signature)
W i t n e s s e db y ( + s i g n a t u r e ) . . . .
A P P r o v ebdY( * s i g n a t u r e. ). . . .
Testinglocation/address
I
Testingprocedure:
SMT
Testedby(name+ signature)
APProved
by(* signature)
.....
Supervised
by(+ signature)...
Testinglocation/
address
X
Testingprocedure:
RMT
Testedby(name+ signature)
Approved
by(+ signature)
.....
Supervised
by(+ signature)..,
Testinglocation/
address
T R F N o | E C E N 6 0 9 510C
Tl RT of CTIEP/lECEE-CB-LABORATORY
Yi 7 Jiuxianqiaobei
Road, ChaoyangDistrict, Beijing, P, R.
China
rlu
Y a nS h i
GaoLingsong
G.
A
),,tq (anat
(/
Page 3 of 50
Report No. CE-002-
07CQC0025L
Summary of testing:
Tests performed (name of test and test clause):
The sample tested complied with all the
requirements of EN 60950-1:2006.
Testing location:
CBTL
Yi 7 Jiuxianqiaobei Road , Chaoyang District ,
Beijing , P. R. China
Summary of compliance with National Differences:
No
Copy of marking plate
TRF No. IECEN60950_1C
Page 4 of 50
Report No. CE-002-
07CQC0025L
Test item particulars .................................................. :
Equipment mobility .................................................... : [ ] movable [] hand-held
[] transportable
[] stationary [] for building-in [] direct plug-in
Connection to the mains ........................................... : [] pluggable equipment [] permanent connection
[ ] detachable power supply cord
[] non-detachable power supply cord
[] not directly connected to the mains
Operating condition ................................................... : [ ] continuous
[] rated operating / resting time:
Over voltage category (OVC) ................................... : [] OVC I
Mains supply tolerance (%)....................................... : +6
[ ] OVC II
[] OVC III
[] OVC IV
, -10%
Tested for IT power systems .................................... : [] Yes
[ ] No
IT testing, phase-phase voltage (V) ......................... : N/A
Class of equipment ................................................... : [ ] Class I [] Class II
[] Not classified
Pollution degree (PD) ............................................... : [] PD 1
[ ] PD 2
[] Class III
[] PD 3
IP protection class .................................................... : IPX0
Altitude during operation (m) .................................... : Below 2000m
Mass of equipment (kg)............................................. : 10.5 kg
Possible test case verdicts:
- test case does not apply to the test object .................: N/A
- test object does meet the requirement.......................: P (Pass)
- test object does not meet the requirement.................: F (Fail)
Testing ..........................................................................:
Date of receipt of test item ............................................: Oct.19,2007
Date(s) of performance of tests ....................................: Oct.20,2007- Dec.12,2007
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.
Note: This TRF includes EN Group Differences together with National Differences and Special
National Conditions, if any. All Differences are located in the Appendix to the main body of this TRF.
Throughout this report a comma (point) is used as the decimal separator.
General product information:
1. Test report includes page 1 to 48. Figures 1 to 8 enclosed.
2. Mains supply tolerance(%):+6
TRF No. IECEN60950_1C
, -10%.
Page 5 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1
GENERAL
P
1.5
Components
P
1.5.1
General
P
Comply with IEC 60950 or relevant component
standard
(see appended table 1.5.1)
P
1.5.2
Evaluation and testing of components
Components, which are
certified to IEC and/or
national standards, are used
correctly within their ratings.
Components not covered by
IEC standards are tested
under the conditions present
in the equipment.
P
1.5.3
Thermal controls
No thermal control.
N
1.5.4
Transformers
Transformers used are
suitable for their intended
application and comply with
the relevant requirements of
the standard and particularly
Annex C.
P
1.5.5
Interconnecting cables
Interconnection cables for
signal output to other devices
and signal input from
accessories are carrying only
SELV voltages on an energy
level below 240VA.
Except for the insulation
material, here are no further
requirements to the
interconnection cable.
P
1.5.6
Capacitors bridging insulation
Double insulation
P
1.5.7
Resistors bridging insulation
Such capacitors used in
approval power supply unit
P
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
N
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
N
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
N
1.5.7.4
Accessible parts
P
1.5.8
Components in equipment for IT power systems
N
1.5.9
Surge suppressors
P
1.5.9.1
General
P
TRF No. IECEN60950_1C
Page 6 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
1.5.9.2
Protection of VDRs
P
1.5.9.3
Bridging of functional insulation by a VDR
P
1.5.9.4
Bridging of basic insulation by a VDR
N
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
N
1.6
Power interface
P
1.6.1
AC power distribution systems
TN power distribution
systems
P
1.6.2
Input current
Highest load according to
1.2.2.1 for this equipment is
the operation with the max.
specified load. Results see
appended table.
Deviation<10%(limited) (see
appended table 1.6.2)
P
1.6.3
Voltage limit of hand-held equipment
This appliance is not a handheld equipment.
N
1.6.4
Neutral conductor
The neutral is not identified in
the equipment. Reinforced or
double insulation for rated
voltage between secondary
parts and primary phase.
P
1.7
Marking and instructions
P
1.7.1
Power rating
P
Rated voltage(s) or voltage range(s) (V) .............. :
Result - Remark
AC100-240V
Symbol for nature of supply, for d.c. only .............. :
Verdict
P
N
Rated frequency or rated frequency range (Hz) ... :
50/60Hz
P
Rated current (mA or A) ........................................ :
Max 1.2A
P
Manufacturer’s name or trade-mark or identification Great Computer (Kunshan)
mark ...................................................................... : Co.,Ltd.
P
Model identification or type reference ................... :
P
SB-60
Symbol for Class II equipment only ...................... :
N
Other markings and symbols ................................ :
N
1.7.2
Safety instructions and marking
1.7.2.1
General
1.7.2.2
Disconnect devices
1.7.2.3
Overcurrent protective device
TRF No. IECEN60950_1C
See User’s manual.
P
P
All-pole mains switch and
appliance couplers are
disconnect devices.
N
N
Page 7 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
1.7.2.4
IT power distribution systems
N
1.7.2.5
Operator access with a tool
N
1.2.7.6
Ozone
N
1.7.3
Short duty cycles
Equipment is designed for
continuous operation.
N
1.7.4
Supply voltage adjustment ................................... :
No voltage adjustment.
N
Methods and means of adjustment; reference to
installation instructions ......................................... :
Ditto.
N
1.7.5
Power outlets on the equipment .......................... :
No standard power supply
outlet
N
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) ......................... :
Power Supply is approved by
CCC, and complies with
IEC60950.
P
1.7.7
Wiring terminals
P
1.7.7.1
Protective earthing and bonding terminals .......... :
P
1.7.7.2
Terminals for a.c. mains supply conductors
N
1.7.7.3
Terminals for d.c. mains supply conductors
N
1.7.8
Controls and indicators
1.7.8.1
Identification, location and marking ..................... :
1.7.8.2
Colours ................................................................ :
1.7.8.3
Symbols according to IEC 60417 ........................ :
Result - Remark
See below.
The marking and indication of
the power switch or functional
switch is located that
indication of function clearly.
No safety relevant controls or
indicators.
The switch on front bezel with
symbol according to
IEC60417, No. 5007” ” and
No. 5008” ”
No indicators for different
positions.
Verdict
P
P
N
P
1.7.8.4
Markings using figures ....................................... :
1.7.9
Isolation of multiple power sources ..................... :
N
1.7.10
Thermostats and other regulating devices ......... :
N
1.7.11
Durability
After this test there was no
damage to the label. The
marking on the label did not
fade. There was neither
curling nor lifting of the label
edge.
P
1.7.12
Removable parts
No removable parts.
N
1.7.13
Replaceable batteries ......................................... :
N
Language(s) ........................................................ :

Equipment for restricted access locations ........... :
N
1.7.14
TRF No. IECEN60950_1C
N
Page 8 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
See below.
P
2.1.1.1
Access to energized parts
No access with test finger and
test pin to any parts with only
basic insulation to ELV or
hazardous voltage. Any
hazardous parts accessible
are unlikely.
P
Test by inspection ..................................................:
Ditto.
P
Test with test finger (Figure 2A) ............................:
Ditto.
P
Test with test pin (Figure 2B) ................................:
Ditto.
P
Test with test probe (Figure 2C) ............................:
No TNV circuits.
N
2.1.1.2
Battery compartments
No battery compartment.
N
2.1.1.3
Access to ELV wiring
No ELV wiring in operator
accessible area.
N
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
Verdict

2.1.1.4
Access to hazardous voltage circuit wiring
No hazardous voltage wiring
in operator accessible area.
N
2.1.1.5
Energy hazards .....................................................:
No Energy hazards
P
2.1.1.6
Manual controls
No conductive shafts of
operating knobs and handles.
N
2.1.1.7
Discharge of capacitors in equipment
The time constant is less than
a second.
P
Measured voltage (V); time-constant (s) ................:
After 1sec, 0V.

Energy hazards – d.c. mains supply
No d.c. mains supply
N
a) Capacitor connected to the d.c. mains supply ..:
Ditto.
N
b) Internal battery connected to the d.c. mains
supply ....................................................................:
Ditto.
N
2.1.1.9
Audio amplifiers .....................................................:
No audio amplifiers
N
2.1.2
Protection in service access areas
No maintenance work in
operation mode necessary.
N
2.1.3
Protection in restricted access locations
No maintenance work in
operation mode necessary.
N
2.2
SELV circuits
2.2.1
General requirements
2.1.1.8
TRF No. IECEN60950_1C
P
See below.
P
Page 9 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.2.2
Voltages under normal conditions (V) ...................:
Between any conductor of the
SELV circuits 42.4V peak or
60Vd.c. are not exceeded.
P
2.2.3
Voltages under fault conditions (V) .......................:
Single fault did not cause
excessive voltage in
accessible SELV circuits.
P
2.2.4
Connection of SELV circuits to other circuits ......:
No direct connection between
SELV and any primary
circuits.
P
2.3
TNV circuits
2.3.1
Limits
N
No TNV circuits
N
Type of TNV circuits ...............................................:

2.3.2
Separation from other circuits and from accessible
parts
N
2.3.2.1
General requirements
N
2.3.2.2
Protection by basic insulation
N
2.3.2.3
Protection by earthing
N
2.3.2.4
Protection by other constructions ..........................:
N
2.3.3
Separation from hazardous voltages
N
Insulation employed................................................:

Connection of TNV circuits to other circuits
N
Insulation employed................................................:

2.3.5
Test for operating voltages generated externally
N
2.4
Limited current circuits
N
2.4.1
General requirements
2.4.2
Limit values
N
Frequency (Hz).......................................................:

Measured current (mA) ..........................................:

Measured voltage (V) .............................................:

Measured circuit capacitance (nF or µF)................:

2.4.3
Connection of limited current circuits to other
circuits
N
2.5
Limited power sources
N
2.3.4
TRF No. IECEN60950_1C
No limited current circuits
N
Page 10 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
a) Inherently limited output
Power Supply is approved by
CCC, and complies with
IEC60950.
Verdict
N
b) Impedance limited output
N
c) Regulating network limited output under normal
operating and single fault condition
N
d) Overcurrent protective device limited output
N
Max. output voltage (V), max. output current (A),
max. apparent power (VA) .....................................:

Current rating of overcurrent protective device (A)

2.6
Provisions for earthing and bonding
P
2.6.1
Protective earthing
P
2.6.2
Functional earthing
P
2.6.3
Protective earthing and protective bonding
conductors
P
2.6.3.1
General
P
2.6.3.2
Size of protective earthing conductors
P
2
Rated current (A), cross-sectional area (mm ),
AWG .......................................................................:
2.6.3.3
2
1.0 mm
Size of protective bonding conductors

P
2
2
Rated current (A), cross-sectional area (mm ),
AWG .......................................................................:
1.0 mm

2.6.3.4
Resistance of earthing conductors and their
terminations; resistance (Ω), voltage drop (V), test
current (A), duration (min) ......................................:
0.055Ω, 32A, 2min
P
2.6.3.5
Colour of insulation.................................................:
Green-and-yellow
P
2.6.4
Terminals
P
2.6.4.1
General
P
2.6.4.2
Protective earthing and bonding terminals
P
Rated current (A), type, nominal thread diameter
(mm) .......................................................................:
<3A, studs and screws type,
3mm

2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
Protective earthing conductor
is in appliance inlet
P
2.6.5
Integrity of protective earthing
P
2.6.5.1
Interconnection of equipment
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
See below
Not Interconnection of
equipment
No switches or overcurrent
protective device in protective
earting conductors and
protective bonding conductors
TRF No. IECEN60950_1C
N
P
Page 11 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.6.5.3
Disconnection of protective earth
2.6.5.4
Parts that can be removed by an operator
2.6.5.5
Parts removed during servicing
2.6.5.6
Corrosion resistance
Appliance inlet provided
Plug or inlet, earthing
connected before and
disconnected after hazardous
voltage. No other operator
removable parts.
It is not necessary to
disconnect earthing except for
the removing of the earthed
part itself.
All safety earthing
connections in compliance
with Annex J.
2.6.5.7
Screws for protective bonding
2.6.5.8
Reliance on telecommunication network or cable
distribution system
2.7
Overcurrent and earth fault protection in primary circuits
2.7.1
Basic requirements
Verdict
P
P
P
P
P
No protective earthing rely on
TNV.
Equipment relies on 16A
rated fuse or circuit breaker of
the wall outlet installation
protection of the building
installation in regard to L to N
short circuit. Overcurrent
protection is provided by the
built-in device fuse.
Instructions when protection relies on building
installation
N
P
P
N
2.7.2
Faults not simulated in 5.3.7
The protection device is well
dimensioned and mounted.
P
2.7.3
Short-circuit backup protection
Pluggable equipment type A.
The building installation is
considered as providing
short-circuit backup
protection.
P
2.7.4
Number and location of protective devices .......... :
Over current protection by
one built-in fuse.
P
2.7.5
Protection by several devices
Only one fuse provided for
mains.
N
2.7.6
Warning to service personnel................................ :
No marking were requested.
N
2.8
Safety interlocks
2.8.1
General principles
2.8.2
Protection requirements
N
2.8.3
Inadvertent reactivation
N
2.8.4
Fail-safe operation
N
TRF No. IECEN60950_1C
N
No safety interlocks
N
Page 12 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
2.8.5
Moving parts
N
2.8.6
Overriding
N
2.8.7
Switches and relays
N
2.8.7.1
Contact gaps (mm) ................................................:
N
2.8.7.2
Overload test
N
2.8.7.3
Endurance test
N
2.8.7.4
Electric strength test
2.8.8
Mechanical actuators
N
2.9
Electrical insulation
P
2.9.1
Properties of insulating materials
2.9.2
Humidity conditioning
Relative humidity (%), temperature (°C) .............. :
Result - Remark
(see appended table 5.2)
No hygroscopic materials
used
Verdict
N
P
P
93% 25
48h

2.9.3
Grade of insulation
P
2.9.4
Separation from hazardous voltages
P
Method(s) used ..................................................... :
Method 1 and Method 3

2.10
Clearances, creepage distances and distances through insulation
P
2.10.1
General
Approval power supply unit
used.
P
2.10.1.1
Frequency ..............................................................:
<30kHz
P
2.10.1.2
Pollution degrees ...................................................:
Pollution 2
P
2.10.1.3
Reduced values for functional insualtion
N
2.10.1.4
Intervening unconnected conductive parts
N
2.10.1.5
Insulation with varying dimensions
N
2.10.1.6
Special separation requirements
N
2.10.1.7
Insulation in circuits generating starting pulses
N
2.10.2
Determination of working voltage
P
2.10.2.1
General
P
2.10.2.2
RMS working voltage
P
2.10.2.3
Peak working voltage
P
2.10.3
Clearances
P
2.10.3.1
General
P
2.10.3.2
Mains transient voltages
P
a) AC mains supply ...............................................:
P
TRF No. IECEN60950_1C
Page 13 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
b) Earthed d.c. mains supplies ..............................:
N
c) Unearthed d.c. mains supplies ..........................:
N
d) Battery operation ...............................................:
N
2.10.3.3
Clearances in primary circuits
(see appended table 2.10.3
and 2.10.4)
P
2.10.3.4
Clearances in secondary circuits
N
2.10.3.5
Clearances in circuits having starting pulses
N
2.10.3.6
Transients from a.c. mains supply .........................:
N
2.10.3.7
Transients from d.c. mains supply .........................:
N
2.10.3.8
Transients from telecommunication networks and
cable distribution systems .....................................:
N
2.10.3.9
Measurement of transient voltage levels
N
a) Transients from a mains suplply
N
For an a.c. mains supply .......................................:
N
For a d.c. mains supply .........................................:
N
b) Transients from a telecommunication network :
N
2.10.4
Creepage distances
P
2.10.4.1
General
2.10.4.2
Material group and caomparative tracking index
CTI tests .................................................................:
Material group IIIb is
assumed to be used

2.10.4.3
Minimum creepage distances
(see appended table 2.10.3
and 2.10.4)
P
2.10.5
Solid insulation
P
2.10.5.1
General
P
2.10.5.2
Distances through insulation
2.10.5.3
Insulating compound as solid insulation
N
2.10.5.4
Semiconductor devices
P
2.10.5.5.
Cemented joints
N
2.10.5.6
Thin sheet material – General
N
2.10.5.7
Separable thin sheet material
N
Number of layers (pcs) ...........................................:

2.10.5.8
Non-separable thin sheet material
N
2.10.5.9
Thin sheet material – standard test procedure
N
Electric strength test

Thin sheet material – alternative test procedure
N
Electric strength test

2.10.5.10
TRF No. IECEN60950_1C
(see appended table 2.10.5)
P
Page 14 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
2.10.5.11
Insulation in wound components
P
2.10.5.12
Wire in wound components
P
Working voltage .....................................................:
Result - Remark
<250V
a) Basic insulation not under stress ......................:
b) Basic, supplemetary, reinforced insulation .......:
Verdict
P
N
(see appended table 2.10.5)
P
c) Compliance with Annex U .................................:
N
Two wires in contact inside wound component;
angle between 45° and 90° ...................................:
N
Wire with solvent-based enamel in wound
components
N
Electric strength test

Routine test
N
Additional insulation in wound components
N
Working voltage .....................................................:
N
- Basic insulation not under stress ........................:
N
- Supplemetary, reinforced insulation ....................:
N
2.10.6
Construction of printed boards
P
2.10.6.1
Uncoated printed boards
2.10.6.2
Coated printed boards
N
2.10.6.3
Insulation between conductors on the same inner
surface of a printed board
N
2.10.6.4
Insulation between conductors on different layers
of a printed board
N
Distance through insulation
N
Number of insulation layers (pcs)...........................:
N
2.10.7
Component external terminations
N
2.10.8
Tests on coated printed boards and coated
components
N
2.10.8.1
Sample preparation and preliminary inspection
N
2.10.8.2
Thermal conditioning
N
2.10.8.3
Electric strength test
N
2.10.8.4
Abrasion resistance test
N
2.10.9
Thermal cycling
N
2.10.10
Test for Pollution Degree 1 environment and
insulating compound
N
2.10.11
Tests for semiconductor devices and cemented
joints
N
2.10.5.13
2.10.5.14
TRF No. IECEN60950_1C
(see appended table 2.10.3
and 2.10.4)
P
Page 15 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
2.10.12
Enclosed and sealed parts
TRF No. IECEN60950_1C
Result - Remark
Verdict
N
Page 16 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
All internal wires are UL
recognized wiring which is
PVC insulated, rated VW-1,
minimum 80°C. Internal wiring
gauge is suitable for current
intended to be carried. No
internal wire for primary
power distribution.
P
3.1.2
Protection against mechanical damage
Wires do not touch sharp
edges, which could damage
the insulation.
P
3.1.3
Securing of internal wiring
Internal wires are secured by
solder pins so that a
loosening of the terminal
connection is unlikely.
P
3.1.4
Insulation of conductors
The insulation of the
individual conductors is
suitable for the application
and the working voltage. For
the insulation material see
3.1.1.
P
3.1.5
Beads and ceramic insulators
Not used.
N
3.1.6
Screws for electrical contact pressure
3.1.7
Insulating materials in electrical connections
All connections are metal to
metal.
N
3.1.8
Self-tapping and spaced thread screws
No self-tapping screws are
used.
N
3.1.9
Termination of conductors
All conductors are reliably
secured by use of solder-pins
or glue or other mechanical
fixing means.
P
10 N pull test
Complied.
P
P
3.1.10
Sleeving on wiring
P
3.2
Connection to a mains supply
P
3.2.1
Means of connection
See below.
P
3.2.1.1
Connection to an a.c. mains supply
Appliance inlet used
P
3.2.1.2
Connection to a d.c. mains supply
No d.c. mains supply.
N
3.2.2
Multiple supply connections
Only one supply connection.
N
TRF No. IECEN60950_1C
Page 17 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
3.2.3
Permanently connected equipment
The unit is not permanently
connected equipment.
N
Number of conductors, diameter of cable and
conduits (mm) ....................................................... :
Ditto.

3.2.4
Appliance inlets
The appliance inlet complies
with IEC/EN 60320-1. The
power cord can be inserted
without difficulties and does
not support the unit.
P
3.2.5
Power supply cords
P
3.2.5.1
AC power supply cords
P
Type ...................................................................... :
2
PVC
Verdict

2
Rated current (A), cross-sectional area (mm ),
AWG ...................................................................... :
10A, 3G1.0 mm

3.2.5.2
DC power supply cords
No d.c. power supply.
N
3.2.6
Cord anchorages and strain relief
Appliance inlet used.
N
Mass of equipment (kg), pull (N) .......................... :

Longitudinal displacement (mm) ........................... :

3.2.7
Protection against mechanical damage
No parts under this unit likely
to damage the power supply
cord. No sharp edge.
P
3.2.8
Cord guards
Appliance inlet used.
N
Diameter or minor dimension D (mm); test mass (g)
............................................................................... :

Radius of curvature of cord (mm) .......................... :

3.2.9
Supply wiring space
3.3
Wiring terminals for connection of external conductors
N
3.3.1
Wiring terminals
N
3.3.2
Connection of non-detachable power supply cords
N
3.3.3
Screw terminals
N
3.3.4
Conductor sizes to be connected
N
Rated current (A), cord/cable type, cross-sectional
area (mm2) ............................................................. :

Wiring terminal sizes
N
Rated current (A), type, nominal thread diameter
(mm) ...................................................................... :

3.3.6
Wiring terminal design
N
3.3.7
Grouping of wiring terminals
N
3.3.5
TRF No. IECEN60950_1C
Appliance inlet used.
Appliance inlet used.
N
Page 18 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
3.3.8
Stranded wire
N
3.4
Disconnection from the mains supply
P
3.4.1
General requirement
Disconnect device provided.
P
3.4.2
Disconnect devices
All-pole mains switch and
appliance couplers
P
3.4.3
Permanently connected equipment
N
3.4.4
Parts which remain energized
N
3.4.5
Switches in flexible cords
3.4.6
Number of poles - single-phase and d.c. equipment The disconnect device
disconnects both poles
simultaneously.
P
3.4.7
Number of poles - three-phase equipment
Single-phase equipment.
N
3.4.8
Switches as disconnect devices
ON : ” ”, OFF: ” ”
P
3.4.9
Plugs as disconnect devices
Appliance inlet provided.
N
3.4.10
Interconnected equipment
Interconnection to other
devices by secondary output
cables only.
N
3.4.11
Multiple power sources
Only one supply connection
provided.
N
3.5
Interconnection of equipment
3.5.1
General requirements
This equipment is not
considered for connection to
TNV.
P
3.5.2
Types of interconnection circuits .......................... :
Interconnection circuits of
SELV and Limited Current
Circuit through sec o/p cable.
P
3.5.3
ELV circuits as interconnection circuits
N
3.5.4
Data ports for additional equipment
N
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
P
Angle of 10°
P
Test force (N) ........................................................ :
N
Mechanical strength
P
4.2
TRF No. IECEN60950_1C
Result - Remark
No switch in flexible cords
Verdict
P
P
Page 19 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
4.2.1
General
See below. After tests, unit
complies with 2.1.1, 2.6.1 and
2.10.
P
4.2.2
Steady force test, 10 N
10N applied to components
other than parts serving as an
enclosure.
P
4.2.3
Steady force test, 30 N
30N applied to covers
P
4.2.4
Steady force test, 250 N
250N applied to metal
enclosure. No energy or other
hazards.
P
4.2.5
Impact test
P
Fall test
P
Swing test
P
4.2.6
Drop test; height (mm) .......................................... :
N
4.2.7
Stress relief test
70
4.2.8
Cathode ray tubes
No cathode ray tube.
N
Picture tube separately certified ........................... :
(see separate test report or
attached certificate)
N
4.2.9
High pressure lamps
No high-pressure lamps
provided.
N
4.2.10
Wall or ceiling mounted equipment; force (N) ...... :
Not wall or ceiling mounted
equipment.
N
4.3
Design and construction
4.3.1
Edges and corners
Edges and corners of the
enclosure are rounded and
smooth
P
4.3.2
Handles and manual controls; force (N) .............:
No handles and manual
controls
N
4.3.3
Adjustable controls
No control device.
N
4.3.4
Securing of parts
Electrical and mechanical
connections can be expected
to with standard usual
mechanical stress. For the
protection, solder pins, cable
ties and heatshrunk tubing
are used.
P
4.3.5
Connection by plugs and sockets
No mismatch of connectors,
plugs or sockets possible.
P
4.3.6
Direct plug-in equipment
N
Torque .................................................................. :

TRF No. IECEN60950_1C
7h
Verdict
P
P
Page 20 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Compliance with the relevant mains plug standard
.............................................................................. :
Verdict
N
4.3.7
Heating elements in earthed equipment
No heating elements
N
4.3.8
Batteries
No batteries provided.
N
- Overcharging of a rechargeable battery
N
- Unintentional charging of a non-rechargeable
battery
N
- Reverse charging of a rechargeable battery
N
- Excessive discharging rate for any battery
N
4.3.9
Oil and grease
Insulation in intended use not
considered to be exposed to
oil or grease.
N
4.3.10
Dust, powders, liquids and gases
None used or generated.
N
4.3.11
Containers for liquids or gases
No container for liquid or gas.
N
4.3.12
Flammable liquids ................................................ :
No flammable liquids
N
Quantity of liquid (l) .............................................. :
Ditto
N
Flash point (°C) .................................................... :
Ditto
N
4.3.13
Radiation
No radiation
N
4.3.13.1
General
No laser
N
4.3.13.2
Ionizing radiation
No ionizing radiation.
N
4.3.13.3
Measured radiation (pA/kg) .................................. :

Measured high-voltage (kV) ................................. :

Measured focus voltage (kV) ............................... :

CRT markings ...................................................... :

Effect of ultraviolet (UV) radiation on materials
No UV radiation.
N
Part, property, retention after test, flammability
classification ......................................................... :
Ditto.
N
4.3.13.4
Human exposure to ultraviolet (UV) radiation ...... :
No UV radiation.
N
4.3.13.5
Laser (including LEDs)
(See separate test report of
IEC/EN 60825-1/
IEC/EN 60825-2)
N
Laser class ........................................................... :
Ditto.

4.3.13.6
Other types .......................................................... :
See clause 4.3.13
N
4.4
Protection against hazardous moving parts
4.4.1
General
No moving parts.
N
4.4.2
Protection in operator access areas .................... :
No moving parts.
N
TRF No. IECEN60950_1C
N
Page 21 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.4.3
Protection in restricted access locations ............. :
The equipment is not
intended to be used in
restricted locations.
N
4.4.4
Protection in service access areas
No moving parts.
N
4.5
Thermal requirements
4.5.1
General
4.5.2
Temperature tests
P
See appended table 4.5
P
P
Normal load condition per Annex L ...................... :
Maximum normal load which
specified by manufacturer.

4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
(see appended table 4.5)
P
4.5.5
Resistance to abnormal heat ............................... :
(see appended table 4.5.5)
N
4.6
Openings in enclosures
P
4.6.1
Top and side openings
P
4.6.2
Dimensions (mm) ................................................. :
No opening within 5°
projection from bare parts at
hazardous voltage or energy
hazard

Bottoms of fire enclosures
There is no opening at
Bottoms enclosure.
N
Construction of the bottomm, dimensions (mm) .. :

4.6.3
Doors or covers in fire enclosures
N
4.6.4
Openings in transportable equipment
4.6.4.1
Constructional design measures
N
Dimensions (mm) ................................................. :

4.6.4.2
Evaluation measures for larger openings
N
4.6.4.3
Use of metallized parts
N
4.6.5
Adhesives for constructional purposes
N
Conditioning temperature (°C), time (weeks) ....... :

4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of flame
P
Not transportable equipment.
Use of materials with the
required flammability
classes.(Method 1 used)
Method 1, selection and application of components Use of materials with the
wiring and materials
required flammability classes.
(see appended table 4.7)
TRF No. IECEN60950_1C
N
P
Page 22 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
4.7.2
Requirement + Test
Result - Remark
Method 2, application of all of simulated fault
condition tests
(see appended table 5.3)
Conditions for a fire enclosure
Verdict
N
P
With having the following
components:
- components in primary
- components in secondary
(not supplied by LPS)
- components having
unenclosed arcing parts at
hazardous voltages or
energy level
- insulated wiring
The fire enclosure is required
See 4.7.2.1
4.7.2.1
Parts requiring a fire enclosure
4.7.2.2
Parts not requiring a fire enclosure
4.7.3
Materials
4.7.3.1
General
Integrated circuits and small
electrical parts mounted on a
printed wiring board min.
rated V-1 or better.
P
4.7.3.2
Materials for fire enclosures
See Annex A2
P
4.7.3.3
Materials for components and other parts outside
fire enclosures
No components or parts
outside fire enclosures.
N
4.7.3.4
Materials for components and other parts inside
fire enclosures
Internal components except
small parts are rated V-2, HF2 or better.
P
4.7.3.5
Materials for air filter assemblies
No air filters provided.
N
4.7.3.6
Materials used in high-voltage components
No high voltage components
provided.
N
TRF No. IECEN60950_1C
P
N
P
Page 23 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
P
5.1
Touch current and protective conductor current
P
5.1.1
General
P
5.1.2
Configuration of equipment under test (EUT)
5.1.2.1
Single connection to an a.c. mains supply
P
5.1.2.2
Redundant multiple connections to an a.c. mains
supply
N
5.1.2.3
Simultaneous multiple connections to an a.c. mains
supply
N
5.1.3
Test circuit
Figure 5A
P
5.1.4
Application of measuring instrument
Tests are conducted using
one of the measuring
instruments in annex D, or
any other circuit giving the
same results.
P
5.1.5
Test procedure
The touch current was
measured from supply to
conductive parts (DC output
connector) and to 10cm by
20cm metal foil wrapped on
accessible non- conductive
parts (plastic enclosure).
P
5.1.6
Test measurements
EUT has only one mains
connection.
Verdict
P
P
Supply voltage (V) ................................................ :
264

Measured touch current (mA) .............................. :
0.180

Max. allowed touch current (mA) ......................... :
0.25

Measured protective conductor current (mA) ...... :
0.555

Max. allowed protective conductor current (mA) .. :
3.5

5.1.7
Equipment with touch current exceeding 3,5 mA
Neither stationary
permanently connected
equipment nor stationary
pluggable equipment type B.
N
5.1.7.1
General ................................................................. :
N
5.1.7.2
Simultaneous multiple connections to the supply
N
5.1.8
Touch currents to telecommunication networks and No TNV.
cable distribution systems and from
telecommunication networks
N
5.1.8.1
Limitation of the touch current to a
telecommunication network or to a cable
distribution system
N
TRF No. IECEN60950_1C
Not connected to
telecommunication
Page 24 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
5.1.8.2
Requirement + Test
Result - Remark
Verdict
Supply voltage (V) ................................................ :

Measured touch current (mA) .............................. :

Max. allowed touch current (mA) ......................... :

Summation of touch currents from
telecommunication networks
No TNV.
N
a) EUT with earthed telecommunication ports ..... :
N
b) EUT whose telecommunication ports have no
reference to protective earth
N
5.2
Electric strength
P
5.2.1
General
(see appended table 5.2)
P
5.2.2
Test procedure
(see appended table 5.2)
P
5.3
Abnormal operating and fault conditions
5.3.1
Protection against overload and abnormal
operation
(see appended table 5.3)
P
5.3.2
Motors
(see appended Annex B)
N
5.3.3
Transformers
(see appended Annex C)
P
5.3.4
Functional insulation ............................................. :
(see appended table 5.2)
P
5.3.5
Electromechanical components
5.3.6
Audio amplifiers in ITE ......................................... :
See separate test report
IEC/EN 60065
N
5.3.7
Simulation of faults
(see appended table 5.3)
P
5.3.8
Unattended equipment
5.3.9
Compliance criteria for abnormal operating and
fault conditions
(see appended table 5.3)
P
5.3.9.1
During the tests
(see appended table 5.3)
P
5.3.9.2
After the tests
(see appended table 5.3)
P
TRF No. IECEN60950_1C
P
N
N
Page 25 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N
6.1.1
Protection from hazardous voltages
N
6.1.2
Separation of the telecommunication network from earth
N
6.1.2.1
Requirements
N
(see appended table 5.2)
Verdict
Supply voltage (V) ................................................ :

Current in the test circuit (mA) ........................... :

6.1.2.2
Exclusions ............................................................ :
N
6.2
Protection of equipment users from overvoltages on telecommunication networks
N
6.2.1
Separation requirements
N
6.2.2
Electric strength test procedure
N
6.2.2.1
Impulse test
(see appended table 5.2)
N
6.2.2.2
Steady-state test
(see appended table 5.2)
N
6.2.2.3
Compliance criteria
N
6.3
Protection of the telecommunication wiring system from overheating
N
Max. output current (A) ........................................ :

Current limiting method ........................................ :

TRF No. IECEN60950_1C
Page 26 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N
7.1
General
N
7.2
Protection of cable distribution system service
persons, and users of other equipment connected
to the system, from hazardous voltages in the
equipment
N
7.3
Protection of equipment users from overvoltages
on the cable distribution system
N
7.4
Insulation between primary circuits and cable
distribution systems
N
7.4.1
General
N
7.4.2
Voltage surge test
(see appended table 5.2)
N
7.4.3
Impulse test
(see appended table 5.2)
N
TRF No. IECEN60950_1C
Result - Remark
Verdict
Page 27 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
P
A.1
Flammability test for fire enclosures of movable
equipment having a total mass exceeding 18 kg,
and of stationary equipment (see 4.7.3.2)
N
A.1.1
Samples ................................................................ :

Wall thickness (mm).............................................. :

A.1.2
Conditioning of samples; temperature (°C) ......... :
N
A.1.3
Mounting of samples ............................................ :
N
A.1.4
Test flame (see IEC 60695-11-3)
N
Flame A, B, C or D ............................................... :

A.1.5
Test procedure
N
A.1.6
Compliance criteria
N
Sample 1 burning time (s)..................................... :

Sample 2 burning time (s)..................................... :

Sample 3 burning time (s)..................................... :

A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
P
A.2.1
Samples, material ................................................. :
Enclosure

Wall thickness (mm).............................................. :
3.6

A.2.2
Conditioning of samples; temperature (°C) ......... :
70°C 7d
P
A.2.3
Mounting of samples ............................................ :
Horizontal
P
A.2.4
Test flame (see IEC 60695-11-4)
Flame A, B or C ................................................... :
Result - Remark
Verdict
P
A

A.2.5
Test procedure
P
A.2.6
Compliance criteria
P
A.2.7
Sample 1 burning time (s)..................................... :
31

Sample 2 burning time (s)..................................... :
31

Sample 3 burning time (s)..................................... :
31

Alternative test acc. to IEC 60695-11-5, cl. 5 and 9
N
Sample 1 burning time (s)..................................... :

Sample 2 burning time (s)..................................... :

Sample 3 burning time (s)..................................... :

A.3
Hot flaming oil test (see 4.6.2)
N
A.3.1
Mounting of samples
N
TRF No. IECEN60950_1C
Page 28 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A.3.2
Test procedure
N
A.3.3
Compliance criterion
N
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N
B.1
General requirements
P
Position ................................................................ :
DC Motor

Manufacturer ........................................................ :
(see appended table 1.5.1)

Type ..................................................................... :
(see appended table 1.5.1)

Rated values ....................................................... :
(see appended table 1.5.1)

B.2
Test conditions
B.3
Maximum temperatures
B.4
Running overload test
N
B.5
Locked-rotor overload test
N
Test duration (days) ............................................. :

Electric strength test: test voltage (V) .................. :

B.6
Running overload test for d.c. motors in secondary
circuits
N
B.6.1
General
N
B.6.2
Test procedure
N
B.6.3
Alternative test procedure
N
B.6.4
Electric strength test; test voltage (V) .................. :
N
B.7
Locked-rotor overload test for d.c. motors in
secondary circuits
P
B.7.1
General
P
B.7.2
Test procedure
B.7.3
Alternative test procedure
N
B.7.4
Electric strength test; test voltage (V) ................. :
N
B.8
Test for motors with capacitors
N
B.9
Test for three-phase motors
N
B.10
Test for series motors
N
Operating voltage (V) ........................................... :

ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)
P
C
P
(see appended table 5.3)
(see appended table 5.3)
P
P
Position ................................................................ :
(see appended table 1.5.1)

Manufacturer ........................................................ :
(see appended table 1.5.1)

TRF No. IECEN60950_1C
Page 29 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Type ..................................................................... :
(see appended table 1.5.1)

Rated values ....................................................... :
(see appended table 1.5.1)

Method of protection ............................................. :
By protection circuit.

C.1
Overload test
N
C.2
Insulation
N
Protection from displacement of windings ............:
N
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4)
P
D.1
Measuring instrument
P
D.2
Alternative measuring instrument
N
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10 and Annex G)
P
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N
G.1
Clearances
N
G.1.1
General
N
G.1.2
Summary of the procedure for determining
minimum clearances
N
G.2
Determination of mains transient voltage (V)
N
G.2.1
AC mains supply .................................................. :
N
G.2.2
Earthed d.c. mains supplies ................................. :
N
G.2.3
Unearthed d.c. mains supplies ............................ :
N
G.2.4
Battery operation .................................................. :
N
G.3
Determination of telecommunication network
transient voltage (V) ............................................. :
N
G.4
Determination of required withstand voltage (V)
N
G.4.1
Mains transients and internal repetitive peaks .... :
N
G.4.2
Transients from telecommunication networks ..... :
N
G.4.3
Combination of transients
N
G.4.4
Transients from cable distribution systems
N
G.5
Measurement of transient voltages (V)
N
a) Transients from a mains supply
N
TRF No. IECEN60950_1C
Considered
Page 30 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
For an a.c. mains supply
N
For a d.c. mains supply
N
b) Transients from a telecommunication network
N
G.6
Determination of minimum clearances ................ :
N
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
P
Metal(s) used ....................................................... :

Complied
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8)
N
K.1
Making and breaking capacity
N
K.2
Thermostat reliability; operating voltage (V) ........ :
N
K.3
Thermostat endurance test; operating voltage (V)
.............................................................................. :
N
K.4
Temperature limiter endurance; operating voltage
(V) ........................................................................ :
N
K.5
Thermal cut-out reliability
N
K.6
Stability of operation
N
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
P
L.1
Typewriters
N
L.2
Adding machines and cash registers
N
L.3
Erasers
N
L.4
Pencil sharpeners
N
L.5
Duplicators and copy machines
N
L.6
Motor-operated files
N
L.7
Other business equipment
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N
M.1
Introduction
N
M.2
Method A
N
M.3
Method B
N
M.3.1
Ringing signal
N
M.3.1.1
Frequency (Hz) .................................................... :

TRF No. IECEN60950_1C
See 1.6.2
P
Page 31 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
M.3.1.2
Voltage (V) ........................................................... :

M.3.1.3
Cadence; time (s), voltage (V) ............................. :

M.3.1.4
Single fault current (mA) ...................................... :

M.3.2
Tripping device and monitoring voltage ............... :
N
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N
M.3.2.2
Tripping device
N
M.3.2.3
Monitoring voltage (V) .......................................... :
N
N
ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9, 6.2.2.1,
7.3.2, 7.4.3 and Clause G.5)
N
N.1
ITU-T impulse test generators
N
N.2
IEC 60065 impulse test generator
N
P
ANNEX P, NORMATIVE REFERENCES

Q
ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1)
N
a) Preferred climatic categories ........................... :
N
b) Maximum continuous voltage .......................... :
N
c) Pulse current .................................................... :
N
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6.2)
N
R.2
Reduced clearances (see 2.10.3)
N
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N
S.1
Test equipment
N
S.2
Test procedure
N
S.3
Examples of waveforms during impulse testing
N
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
N

TRF No. IECEN60950_1C
Page 32 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
Verdict
N

V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N
V.1
Introduction
N
V.2
TN power distribution systems
N
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N
W.1
Touch current from electronic circuits
N
W.1.1
Floating circuits
N
W.1.2
Earthed circuits
N
W.2
Interconnection of several equipments
N
W.2.1
Isolation
N
W.2.2
Common return, isolated from earth
N
W.2.3
Common return, connected to protective earth
N
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause
C.1)
N
X.1
Determination of maximum input current
N
X.2
Overload test procedure
N
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N
Y.1
Test apparatus ..................................................... :
N
Y.2
Mounting of test samples ..................................... :
N
Y.3
Carbon-arc light-exposure apparatus .................. :
N
Y.4
Xenon-arc light exposure apparatus .................... :
N
Z
ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2)
N
AA
ANNEX AA, MANDREL TEST (see 2.10.5.8)
N
BB
ANNEX BB, CHANGES IN THE SECOND EDITION

TRF No. IECEN60950_1C
Page 33 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
EN 60950-1:2006 – CENELEC COMMON MODIFICATIONS
Contents
Add the following annexes:
N
Annex ZA (normative)
Normative references to international publications
with their corresponding European publications
Annex ZB (normative)
Annex ZC (informative)
General
A-deviations
Delete all the “country” notes in the reference document according to the following
list:
1.4.8
1.5.8
2.2.3
2.3.2.1
2.7.1
3.2.1.1
4.3.6
4.7.3.1
6
6.2.2
7.1
G.2.1
1.3.Z1
Special national conditions
Note 2
Note 2
Note
Note 2
Note
Note
Note 1 & 2
Note 2
Note 2 & 5
Note 6.
Note 3
Note 2
1.5.1
1.5.9.4
2.2.4
2.3.4
2.10.3.2
3.2.4
4.7
5.1.7.1
6.1.2.1
2.2.1
7.2
Annex H
Note 2 & 3
Note
Note
Note 2
Note 2
Note 3.
Note 4
Note 3 & 4
Note 2
Note 2
Note
Note 2
1.5.7.1
1.7.2.1
2.3.2
2.6.3.3
2.10.5.13
2.5.1
4.7.2.2
5.3.7
6.1.2.2
6.2.2.2
7.3
N
Note
Note 4, 5 & 6
Note
Note 2 & 3
Note 3
Note 2
Note
Note 1
Note
Note
Note 1 & 2
Add the following subclause:
N
1.3.Z1 Exposure to excessive sound pressure
The apparatus shall be so designed and constructed as to present no danger when
used for its intended purpose, either in normal operating conditions or under fault
conditions, particularly providing protection against exposure to excessive sound
pressures from headphones or earphones.
NOTE Z1 A new method of measurement is described in EN 50332-1, Sound system
equipment:
Headphones and earphones associated with portable audio equipment - Maximum sound
pressure level measurement methodology and limit considerations - Part 1: General method
for “one package equipment”, and in EN 50332-2, Sound system equipment: Headphones
and earphones associated with portable audio equipment - Maximum sound pressure level
measurement methodology and limit considerations - Part 2: Guidelines to associate sets
with headphones coming from different manufacturers.
1.5.1
Add the following NOTE:
N
NOTE Z1 The use of certain substances in electrical and electronic equipment is restricted
within the EU: see Directive 2002/95/EC
1.7.2.1
Add the following NOTE:
NOTE Z1 In addition, the instructions shall include, as far as applicable, a warning that
excessive sound pressure from earphones and headphones can cause hearing loss
TRF No. IECEN60950_1C
N
Page 34 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
2.7.1
Replace the subclause as follows:
Result - Remark
Verdict
N
Basic requirements
To protect against excessive current, short-circuits and earth faults in PRIMARY
CIRCUITS, protective devices shall be included either as integral parts of the
equipment or as parts of the building installation, subject to the following, a), b) and
c):
a) except as detailed in b) and c), protective devices necessary to comply with the
requirements of 5.3 shall be included as parts of the equipment;
b) for components in series with the mains input to the equipment such as the
supply cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault
protection may be provided by protective devices in the building installation;
c) it is permitted for PLUGGABLE EQUIPMENT TYPE B or PERMANENTLY
CONNECTED EQUIPMENT, to rely on dedicated overcurrent and short-circuit
protection in the building installation, provided that the means of protection, e.g.
fuses or circuit breakers, is fully specified in the installation instructions.
If reliance is placed on protection in the building installation, the installation
instructions shall so state, except that for PLUGGABLE EQUIPMENT TYPE A the
building installation shall be regarded as providing protection in accordance with
the rating of the wall socket outlet.
2.7.2
This subclause has been declared ‘void’.
N
3.2.3
Delete the NOTE in Table 3A, and delete also in this table the conduit sizes in
parentheses.
N
3.2.5.1
Replace
N
“60245 IEC 53” by “H05 RR-F”;
“60227 IEC 52” by “H03 VV-F or H03 VVH2-F”;
“60227 IEC 53” by “H05 VV-F or H05 VVH2-F2”.
In Table 3B, replace the first four lines by the following:
| Up to and including 6
|
| Over 6 up to and including 10 |
| Over 10 up to and including 16 |
(0,75)
(1,0) c)
0,75 a)
1,0
1,5
b)
|
|
|
In the conditions applicable to Table 3B delete the words “in some countries” in
condition a).
In NOTE 1, applicable to Table 3B, delete the second sentence.
3.3.4
In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with
the following:
| Over 10 up to and including 16 |
1,5 to 2,5
|
1,5 to 4
N
|
Delete the fifth line: conductor sizes for 13 to 16 A.
4.3.13.6
Add the following NOTE:
NOTE Z1 Attention is drawn to 1999/519/EC: Council Recommendation on the limitation of
exposure of the general public to electromagnetic fields 0 Hz to 300 GHz. Standards taking
into account this Recommendation which demonstrate compliance with the applicable EU
Directive are indicated in the OJEC.
TRF No. IECEN60950_1C
N
Page 35 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Annex H
Replace the last paragraph of this annex by:
Result - Remark
Verdict
N
At any point 10 cm from the surface of the OPERATOR ACCESS AREA, the dose
rate shall not exceed 1 Sv/h (0,1 mR/h) (see NOTE). Account is taken of the
background level.
Replace the notes as follows:
NOTE These values appear in Directive 96/29/Euratom.
Delete NOTE 2.
Bibliography
Additional EN standards.

ZA
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR
CORRESPONDING EUROPEAN PUBLICATIONS

ZB
SPECIAL NATIONAL CONDITIONS
N
1.2.4.1
In Denmark, certain types of Class I appliances (see 3.2.1.1) may be provided with
a plug not establishing earthing conditions when inserted into Danish socketoutlets.
N
1.5.7.1
In Finland, Norway and Sweden, resistors bridging BASIC INSULATION in
CLASS I PLUGGABLE EQUIPMENT TYPE A must comply with the requirements
in 1.5.7.2.
N
1.5.8
In Norway, due to the IT power system used (see annex V, Figure V.7), capacitors
are required to be rated for the applicable line-to-line voltage (230 V).
N
1.5.9.4
In Finland, Norway and Sweden, the third dashed sentence is applicable only to
equipment as defined in 6.1.2.2 of this annex.
N
1.7.2.1
In Finland, Norway and Sweden, CLASS I PLUGGABLE EQUIPMENT TYPE A
intended for connection to other equipment or a network shall, if safety relies on
connection to protective earth or if surge suppressors are connected between the
network terminals and accessible parts, have a marking stating that the equipment
must be connected to an earthed mains socket-outlet.
N
The marking text in the applicable countries shall be as follows:
In Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun
pistorasiaan"
In Norway: “Apparatet må tilkoples jordet stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat uttag”
1.7.5
In Denmark, socket-outlets for providing power to other equipment shall be in
accordance with the Heavy Current Regulations, Section 107-2-D1, Standard
Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For
STATIONARY EQUIPMENT the socket-outlet shall be in accordance with Standard
Sheet DK 1-1b or DK 1-5a.
N
2.2.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex.
N
2.3.2
In Finland, Norway and Sweden there are additional requirements for the
insulation. See 6.1.2.1 and 6.1.2.2 of this annex.
N
TRF No. IECEN60950_1C
Page 36 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
2.3.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex.
N
2.6.3.3
In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not
16 A.
N
2.7.1
In the United Kingdom, to protect against excessive currents and short-circuits in
the PRIMARY CIRCUIT of DIRECT PLUG-IN EQUIPMENT, tests according to 5.3
shall be conducted, using an external protective device rated 30 A or 32 A. If these
tests fail, suitable protective devices shall be included as integral parts of the
DIRECT PLUG-IN EQUIPMENT, so that the requirements of 5.3 are met.
N
2.10.5.13
In Finland, Norway and Sweden, there are additional requirements for the
insulation, see 6.1.2.1 and 6.1.2.2 of this annex.
N
3.2.1.1
In Switzerland, supply cords of equipment having a RATED CURRENT not
exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC
60884-1 and one of the following dimension sheets:
N
SEV 6532-2.1991
SEV 6533-2.1991
SEV 6534-2.1991
Result - Remark
Plug Type 15
Plug Type 11
Plug Type 12
3P+N+PE
L+N
L+N+PE
Verdict
250/400 V, 10 A
250 V, 10 A
250 V, 10 A
In general, EN 60309 applies for plugs for currents exceeding 10 A. However, a 16
A plug and socket-outlet system is being introduced in Switzerland, the plugs of
which are according to the following dimension sheets, published in February
1998:
SEV 5932-2.1998
SEV 5933-2.1998
SEV 5934-2.1998
3.2.1.1
Plug Type 25
Plug Type 21
Plug Type 23
3L+N+PE
L+N
L+N+PE
230/400 V, 16 A
250 V, 16 A
250 V, 16 A
In Denmark, supply cords of single-phase equipment having a rated current not
exceeding13 A shall be provided with a plug according to the Heavy Current
Regulations, Section 107-2-D1.
N
CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which
are intended to be used in locations where protection against indirect contact is
required according to the wiring rules shall be provided with a plug in accordance
with standard sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase equipment having a RATED CURRENT
exceeding 13 A is provided with a supply cord with a plug, this plug shall be in
accordance with the Heavy Current Regulations, Section 107-2-D1 or EN 60309-2.
3.2.1.1
In Spain, supply cords of single-phase equipment having a rated current not
exceeding 10 A shall be provided with a plug according to UNE 20315:1994.
Supply cords of single-phase equipment having a rated current not exceeding 2,5
A shall be provided with a plug according to UNE-EN 50075:1993.
CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which
are intended to be used in locations where protection against indirect contact is
required according to the wiring rules, shall be provided with a plug in accordance
with standard UNE 20315:1994.
If poly-phase equipment is provided with a supply cord with a plug, this plug shall
be in accordance with UNE-EN 60309-2.
TRF No. IECEN60950_1C
N
Page 37 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
3.2.1.1
In the United Kingdom, apparatus which is fitted with a flexible cable or cord and
is designed to be connected to a mains socket conforming to BS 1363 by means of
that flexible cable or cord and plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994 - The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by those regulations.
Verdict
N
NOTE ‘Standard plug’ is defined in SI 1768:1994 and essentially means an approved plug
conforming to BS 1363 or an approved conversion plug.
3.2.1.1
In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to
be connected to a mains socket conforming to I.S. 411 by means of that flexible
cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory
Instrument 525:1997 - National Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic Use) Regulations 1997.
N
3.2.4
In Switzerland, for requirements see 3.2.1.1 of this annex.
N
3.2.5.1
In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is
allowed for equipment with a rated current over 10 A and up to and including 13 A.
N
3.3.4
In the United Kingdom, the range of conductor sizes of flexible cords to be
accepted by terminals for equipment with a RATED CURRENT of over 10 A up to
and including 13 A is:
N
• 1,25 mm2 to 1,5 mm2 nominal cross-sectional area.
4.3.6
In the United Kingdom, the torque test is performed using a socket outlet
complying with BS 1363 part 1:1995, including Amendment 1:1997 and
Amendment 2:2003 and the plug part of DIRECT PLUG-IN EQUIPMENT shall be
assessed to BS 1363: Part 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, 12.16 and
12.17, except that the test of 12.17 is performed at not less than 125 °C. Where the
metal earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the
requirements of clauses 22.2 and 23 also apply.
N
4.3.6
In Ireland, DIRECT PLUG-IN EQUIPMENT is known as plug similar devices. Such
devices shall comply with Statutory Instrument 526:1997 - National Standards
Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets
for domestic use) Regulations, 1997.
N
5.1.7.1
In Finland, Norway and Sweden TOUCH CURRENT measurement results
exceeding 3,5 mA r.m.s. are permitted only for the following equipment:
N
• STATIONARY PLUGGABLE EQUIPMENT TYPE A that
is intended to be used in a RESTRICTED ACCESS LOCATION
where
equipotential bonding has been applied, for example, in a
telecommunication centre; and
has provision for a permanently connected PROTECTIVE
EARTHING
CONDUCTOR; and
is provided with instructions for the installation of that conductor by a
SERVICE PERSON;
• STATIONARY PLUGGABLE EQUIPMENT TYPE B;
• STATIONARY PERMANENTLY CONNECTED EQUIPMENT.
TRF No. IECEN60950_1C
Page 38 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
6.1.2.1
In Finland, Norway and Sweden, add the following text between the first and
second paragraph of the compliance clause:
Verdict
N
If this insulation is solid, including insulation forming part of a component, it shall at
least consist of either
-
two layers of thin sheet material, each of which shall pass the electric
strength test below, or
one layer having a distance through insulation of at least 0,4 mm, which
shall
pass the electric strength test below.
If this insulation forms part of a semiconductor component (e.g. an optocoupler),
there is no distance through insulation requirement for the insulation consisting of
an insulating compound completely filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the component passes the electric
strength test in accordance with the compliance clause below and in addition
-
passes the tests and inspection criteria of 2.10.11 with an electric strength
test of 1,5 kV multiplied by 1,6 (the electric strength test of 2.10.10 shall be
performed using 1,5 kV), and
-
is subject to ROUTINE TESTING for electric strength during manufacturing,
using a test voltage of 1,5 kV.
It is permitted to bridge this insulation with a capacitor complying with
EN 132400:1994, subclass Y2.
A capacitor classified Y3 according to EN 132400:1994, may bridge this insulation
under the following conditions:
-
the insulation requirements are satisfied by having a capacitor classified Y3
as defined by EN 132400, which in addition to the Y3 testing, is tested with
an impulse test of 2,5 kV defined in EN 60950-1:2006, 6.2.2.1;
-
the additional testing shall be performed on all the test specimens as
described in EN 132400;
-
the impulse test of 2,5 kV is to be performed before the endurance test in
EN 132400, in the sequence of tests as described in EN 132400.
6.1.2.2
In Finland, Norway and Sweden, the exclusions are applicable for
PERMANENTLY CONNECTED EQUIPMENT, PLUGGABLE EQUIPMENT TYPE
B and equipment intended to be used in a RESTRICTED ACCESS LOCATION
where equipotential bonding has been applied, e.g. in a telecommunication centre,
and which has provision for a permanently connected PROTECTIVE EARTHING
CONDUCTOR and is provided with instructions for the installation of that conductor
by a SERVICE PERSON.
N
7.2
In Finland, Norway and Sweden, for requirements see 6.1.2.1 and 6.1.2.2 of this
annex.
N
The term TELECOMMUNICATION NETWORK in 6.1.2 being replaced by the term
CABLE DISTRIBUTION SYSTEM.
7.3
In Norway and Sweden, there are many buildings where the screen of the coaxial
cable is normally not connected to the earth in the building installation.
N
7.3
In Norway, for installation conditions see EN 60728-11:2005.
N
TRF No. IECEN60950_1C
Page 39 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
ZC
A-DEVIATIONS (informative)
1.5.1
Sweden (Ordinance 1990:944)
Verdict
N
Add the following:
NOTE In Sweden, switches containing mercury are not permitted.
1.5.1
Switzerland (Ordinance on environmentally hazardous substances SR 814.081,
Annex 1.7, Mercury - Annex 1.7 of SR 814.81 applies for mercury.)
N
Add the following:
NOTE In Switzerland, switches containing mercury such as thermostats, relays and level
controllers are not allowed.
1.7.2.1
N
Denmark (Heavy Current Regulations)
Supply cords of CLASS I EQUIPMENT, which is delivered without a plug, must be
provided with a visible tag with the following text:
Vigtigt!
Lederen med grøn/gul isolation
må kun tilsluttes en klemme mærket
eller
If essential for the safety of the equipment, the tag must in addition be provided
with a diagram, which shows the connection of the other conductors, or be
provided with the following text:
“For tilslutning af de øvrige ledere, se medfølgende installationsvejledning.”
1.7.2.1
Germany (Gesetz über technische Arbeitsmittel und Verbraucherprodukte (Geräteund Produktsicherheitsgesetz – GPSG) [Law on technical labour equipment and
consumer products], of 6th January 2004, Section 2, Article 4, Clause (4), Item 2).
N
If for the assurance of safety and health certain rules during use, amending or
maintenance of a technical labour equipment or readymade consumer product are
to be followed, a manual in German language has to be delivered when placing the
product on the market.
Of this requirement, rules for use even only by SERVICE PERSONS are not
exempted.
1.7.5
Denmark (Heavy Current Regulations)
N
With the exception of CLASS II EQUIPMENT provided with a socket outlet in
accordance with the Heavy Current Regulations, Section 107-2-D1, Standard
Sheet DK 1-4a, CLASS II EQUIPMENT shall not be fitted with socket-outlets for
providing power to other equipment.
1.7.13
Switzerland (Ordinance on chemical hazardous risk reduction SR 814.81, Annex
2.15 Batteries)
N
Annex 2.15 of SR 814.81 applies for batteries.
5.1.7.1
Denmark (Heavy Current Regulations, Chapter 707, clause 707.4)
TOUCH CURRENT measurement results exceeding 3,5 mA r.m.s. are permitted
only for PERMANENTLY CONNECTED EQUIPMENT and PLUGGABLE
EQUIPMENT TYPE B.
TRF No. IECEN60950_1C
N
Page 40 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
1.5.1
TABLE: List of critical components
Object/part
No.
Manufacturer/
trademark
Power supply GUANGZHOU
MEANWELL
ELECTRONICS
CO., LTD.
Result - Remark
Type/model
PD-65B
Verdict
P
Technical data
Standard
(Edition / year)
Mark(s) of
conformity1)
Input:
100- IEC60950
240VAC
50/60Hz
1.5A
Output:
+5VDC/3.5A,
+24VDC/2A
CCC
2004010907114
905
Plug
Shenzhen Dongju DJ-012
Wire
&
Cable
Co., Ltd.
16 A 250V
DIN 49441-R2
40011580
Cord
Shenzhen Dongju H03VV-F
Wire
&
Cable
Co., Ltd.
3 x 1.0 mm²
DIN 0281-5
129988
10 A 250V
Sheet 13
40013015
Connector
Shenzhen Dongju DJ-022
Wire
&
Cable
Co., Ltd.
Filter
wih High
&
Low 03SS1-B-Q(B)
Appliance
Corporation
inlet
115/250VAC 3A IEC60939
50/60Hz
VDE40008353
250V
IEC60947
50/60Hz
6A/12A 250VAC IEC61058-1
1E4
VDE 137453
Switch
Trankey
Micro- ZE-800
Tech Corporation
KCD1-104
ZHEJIANG
ZHONGXUN
ELECTRONICS
CO.,LTD.
CQC030020071
80
Motor
FEIHONG
3VDC 1.5A
IEC609501:2005
--
Ø
IEC609501:2005
--
Breaker
Sleeving
wiring
on WORE
HEATSHRINKABLE
MATERIAL
(Shenzhen)
17HD403-3B
Enclosure
YUANYI Shanghai,
China
Comply
with IEC60950Tested
ANNEX A2
1:2005 ANNEX appliance
A2
Control PCB
SHUNDE JUNDA
ELECTRONIC CO
LTD
V-1 or Better
1
UL94
) An asterisk indicates a mark which assures the agreed level of surveillance
Supplementary information:
TRF No. IECEN60950_1C
E173873
in
Page 41 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
1.6.2
TABLE: Electrical data (in normal conditions)
Verdict
P
U (V)
I (A)
Irated (A)
P (W)
Fuse #
90V/
50Hz
0.293/0.19
9
MAX.1.2
16.8/11.3
--
0.293/0.19 Normal operating/Standby
9
90V/
60Hz
0.295/0.20
0
MAX.1.2
16.9/11.4
--
0.295/0.20 Normal operating/Standby
0
100V/
50Hz
0.273/0.18
1
MAX.1.2
17.3/11.2
--
0.273/0.18 Normal operating/Standby
1
100V/
60Hz
0.275/0.18
3
MAX.1.2
17.3/11.2
--
0.275/0.18 Normal operating/Standby
3
220V/
50Hz
0.171/0.15
0
MAX.1.2
16.5/13.7
--
0.171/0.15 Normal operating/Standby
0
220V/
60Hz
0.173/0.15
2
MAX.1.2
16.6/13.8
--
0.173/0.15 Normal operating/Standby
2
240V/
50Hz
0.170/0.15
1
MAX.1.2
16.6/14.2
--
0.170/0.15 Normal operating/Standby
1
240V/
60Hz
0.172/0.15
3
MAX.1.2
16.6/14.2
--
0.172/0.15 Normal operating/Standby
3
254V/
50Hz
0.171/0.15
4
MAX.1.2
16.4/14.6
--
0.171/0.15 Normal operating/Standby
4
254V/
60Hz
0.172/0.15
5
MAX.1.2
16.5/14.6
--
0.172/0.15 Normal operating/Standby
5
264V/
50Hz
0.172/0.15
1
MAX.1.2
16.3/14.7
--
0.172/0.15 Normal operating/Standby
1
264V/
60Hz
0.173/0.15
3
MAX.1.2
16.4/14.8
--
0.173/0.15 Normal operating/Standby
3
Supplementary information:
TRF No. IECEN60950_1C
Ifuse (A)
Condition/status
Page 42 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
2.10.3 and
2.10.4
TABLE: Clearance and creepage distance measurements
Clearance (cl) and creepage
distance (cr) at/of/between:
Result - Remark
Verdict
P
U peak
(V)
U r.m.s.
(V)
Required cl
(mm)
cl
(mm)
Required cr
(mm)
cr
(mm)
Between L and N (CN1)
373
264
1.5
3.3
2.8
3.3
Between primary conductor
and secondary conductor on
PCB near T1
417
241
4.0
6.7
6.4
6.7
Between primary conductor
and secondary conductor on
PCB near U2
118
105
4.0
6.2
4.0
6.2
Supplementary information:
2.10.5
TABLE: Distance through insulation measurements
Distance through insulation (DTI) at/of:
Supplementary information:
TRF No. IECEN60950_1C
U peak
(V)
U rms
(V)
N
Test
voltage
(V)
Required DTI
(mm)
DTI
(mm)
Page 43 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
4.3.8
TABLE: Batteries
Result - Remark
Verdict
N
The tests of 4.3.8 are applicable only when appropriate battery
data is not available
N
Is it possible to install the battery in a reverse polarity position?
N
Non-rechargeable batteries
Discharging
Meas.
current
Manuf.
Specs.
Unintentional
charging
Rechargeable batteries
Charging
Meas.
current
Manuf.
Specs.
Discharging
Meas.
current
Manuf.
Specs.
Reversed
charging
Meas.
current
Manuf.
Specs.
Max.
current
during
normal
condition
Max.
current
during
fault
condition
Test results:
- Chemical leaks
- Explosion of the battery
- Emission of flame or expulsion of molten metal
- Electric strength tests of equipment after completion of tests
Supplementary information:
TRF No. IECEN60950_1C
Verdict
Page 44 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
4.5
TABLE: Thermal requirements
Verdict
N
Supply voltage (V) .......................... 254V
90V

Ambient Tmin (°C) ............................. 17.2
17.5

Ambient Tmax (°C) ............................ 17.7
17.7

Maximum measured temperature T of part/at:
Allowed
Tmax
(°C)
T (°C)
Appliance inlet
30.3
33.6
60
Switch
29.2
31.8
50
Motor
36.5
38.8
/
Control bard PCB
35.6
37.1
85
Metal enclosure (rear)
33.4
35.7
40
Metal enclosure (top)
28.3
28.4
60
Power supply PCB
51.4
54.3
85
T1 coil
49.1
51.4
85
T1 wire
56.7
60.5
85
Supplementary information:
Temperature T of winding:
t1 (°C)
R1 (Ω)
t2 (°C)
R2 (Ω)
T (°C)
Allowed
Tmax (°C)
Insulatio
n class
Supplementary information:
4.5.5
TABLE: Ball pressure test of thermoplastic parts
N
Allowed impression diameter (mm) .....................:

Part
Test temperature Impression diameter
(mm)
(°C)
Supplementary information:
4.7
TABLE: Resistance to fire
Part
Manufacturer of
material
TRF No. IECEN60950_1C
(See appended table 1.5.1)
Type of material
Thickness Flammability
(mm)
class
P
Evidence
Page 45 of 50
Report No. CE-002-07CQC0025L
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Supplementary information:
5.2
TABLE: Electric strength tests, impulse tests and voltage surge tests
Test voltage applied between:
P
Voltage shape Test voltage
(AC, DC,
(V)
impulse, surge)
Breakdow
n
Yes / No
Primary circuits to protective earth
AC
1500
No
Primary circuits to secondary terminals
AC
3000
No
L to N
AC
1500
No
Supplementary information:
5.3
TABLE: Fault condition tests
Ambient temperature (°C) ...................................:
18.5

Power source for EUT: Manufacturer, model/type,
output rating .........................................................:
--

Component
No.
Motor
P
Fault
S/C
Supply
voltage
(V)
Test
time
Fuse #
Fuse
current
(A)
254
4h
--
--
Supplementary information:
1) S/C = Short Circuit
2) NH = No Hazard Occurred ;NFR = No Further Results existed
TRF No. IECEN60950_1C
Observation
T1 winding of power supply
maximal temperature was 53.2
. motor maximal temperature
was 48.6 .
Page 46 of 50
Report No. CE-002-07CQC0025L
List of test equipment used:
(Note: This is an example of the required attachment. Other forms with a different layout but
containing similar information are also acceptable.)
Clause
1.6.2
Measurement /
testing
Input current
Testing / measuring
equipment / material used
Isolation booster
Digital Power Analyzer
Range used
AC2-300V MAX.4KVA
1~999.9Hz
500V 4/40A
Digital Electric-parameter
2.1.1.1/
Calibration
date
2007.3.10
2007.1.16
2007.6.14
Protection in
operator access
areas
Test finger
Test pin
Push-pull Meter
2.6.3.4
Resistance of
earthing
conductors and
their terminations
Earthing bond tester
2.9.2
Humidity
conditioning
Constant temperature and
Humidity Chamber
2.10.3/
2.10. 4
creepage distance
/clearance distance
Cursor Callipers
4.2.5
Impact test
Steel ball
4.5
Thermal
requirements
Multipoint temperature tester
4.5.5
Resistance to
abnormal heat
Ball pressure test device with
heat chamber
R=2.5mm
4.7
Resistance to fire
Bunsen burner
Methane
Diameter : 9.5±0.5mm
Length :100mm
37MJ/m3
2007.2.20
5.1
Touch current and
protective
conductor current
Touch current test device
Figure D.1
2007.1.18
Digital memory oscilloscope
Frequency
range :10Hz-100MHz
Voltage accuracy:
±2.5%
2007.10.25
4.2.3/4.
3.2
fig.2A
fig.2B
0-10kg
2007.10.5
0-20kg
0-50A; 0.1Ω;12V
2007.1.7
Temperature:-40
+100 Humidity:30%
98% Accuracy: ±1
/±5%RH
2007.4.16
Range 130mm,
Accuracy: 0.02mm
2007.3.30
Ø50mm 500g
2007.1.7
25
24chunnel 300
0
2007.7.27
2007.3.13
300oC
Measuring voltage :05KV±3%
Output current :0100mA
5.2
Electric strength
Dielectric Strength Test
Instrument
5.3
Abnormal
operating and fault
conditions
Digital Electric-parameter
500V 4/40A
2007.6.14
Stop-watch
Accuracy 0.01s
2007.8.9
TRF No. IECEN60950_1C
2007.1.14
Page 47 of 50
Figure 1
Figure 2
TRF No. IECEN60950_1C
Report No. CE-002-07CQC0025L
Page 48 of 50
Figure 3
Figure 4
TRF No. IECEN60950_1C
Report No. CE-002-07CQC0025L
Page 49 of 50
Figure 5
Figure 6
TRF No. IECEN60950_1C
Report No. CE-002-07CQC0025L
Page 50 of 50
Figure 7
Figure 8
TRF No. IECEN60950_1C
Report No. CE-002-07CQC0025L
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement