WL-090 LED Dental Curing Light

WL-090 LED Dental Curing Light
LEDEXTM
WL-090
LED Dental Curing Light
User’s manual
A lot of research & development has gone into the manufacturing of this
product and we sincerely hope that it will give you many years of trouble-free
use. Please read and understand all the instructions before using this
equipment, and save this manual for your reference.
EN
LED Dental Curing Light EN
!
!
!
!
!
!
This icon marks warnings, information that should be read before
using your product to prevent possible injury.
Use only the authorized parts provided for the purpose to maintain
compliance with product regulations.
Do not disassemble. Touching the product’s internal parts could
result in injury. In the event of a malfunction, the product should be
repaired only by a qualified technician.
When inserting the battery, do not attempt to insert it upside down.
Do not short or disassemble the battery. Do not expose the battery
to flame or to excessive heat. Do not immerse in or expose to water.
For as long a life cycle of battery as possible, please return the
hand-piece to the cradle as often as possible, and do not store
battery for longer than 6 months. In order to avoid irrevocable deep
discharge if the battery is not used, a new battery is best purchased
only once the old battery needs to be replaced. Since the battery is
a consumable, it has to be replaced if the performance drops
considerably or after its typical life cycle has expired after approx. 30
months.
TM
The LEDEX WL-090 is the specialized equipment for dental
department and it should be operated by specialist only in the dental
clinic. To avoid to damage the eyes please do not point the beam of
the light toward the eyes.
LEDEXTM WL-090
LED Dental Curing Light EN
!
!
Do not exceed recommended irradiation time and light intensity for
an application as tooth overheating may result.
Please do not continuously irradiate on any specific area for a long
time because it may cause the head of the device to be too hot. If so,
we strongly suggest you to move it away for a while. Remember to
properly adjust the time of light irradiation according to different light
intensity.
!
It is danger of explosion if battery is incorrectly replaced. To reduce
risk of fire or burns, do not disassemble, crush, puncture, short
external contacts, expose to temperature above 60 ℃ (140℉), or
dispose of in fire or water. Replace only with specified batteries.
Recycle or dispose of used batteries according to the local
regulations or reference guide supplied with your product.
LEDEXTM WL-090
LED Dental Curing Light EN
Indication for use:
LEDEX WL-090 is a visible curing unit programmed for polymerization of dental
light cured materials by dental professionals.
Conditions for use:
10℃~40℃ , 30%~75% relative humidity
500hPa~1060hPa atmospheric pressure
Conditions for storage and transport:
10℃~40℃, 10%~95% relative humidity
500hPa~1060hPa atmospheric pressure
LEDEXTM WL-090
LED Dental Curing Light EN
Properties of the LEDEXTM WL-090:
1. The light has been manufactured with a super-high luminosity 10 W
LEDs. The light wavelength of WL-090 is between 440 and 480 nm and
the intensity is up to 2400 mW/cm², it can cure the composite over 2
mm in 2 sec. These characteristics enable the light to polymerize
almost all photosensitive composite resins.
2. 6 powerful extensive modes including Low, Ramp, Standard, High, Fast
Ortho, Turbo modes.
3. The turbo light guide rod is made from genuine optical fiber and not
inferior acrylic that optimizes light conduction and minimizes loss of
light from source to tip thereby ensuring the highest possible intensity
of light at the light guide tip.
4. Advanced and high efficient cooling heat sink designed accompanied
with over temperature protection. A thermal protection circuit and safety
mode accord to protect the light from overheating.
5. The automatic memorization of the last operation chosen is another
unique feature of the light.
6. It has OLED display, built-in radiometer, auto sleep designed for saving
the energy of battery.
2
sec
Cure 2 mm
6
Powerful
modes
LEDEXTM WL-090
FAST
ORTHO
TURBO
2400
mW/cm
2
OLED
96x64x3
pixels
Built-in
Cartridge
Radiometer
Battery
LED Dental Curing Light EN
Contents:
Description
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
Numbers of items
LEDEX™ W L-090 handpiece…………………….………………….....1
Battery (Including in handpiece, 3.7V/2500mAh)…………………………1
Cr adle… ………… ……… …………… ………… …… …………… ……… 1
Power supply (Input AC100~240 V, 50/60Hz, output DC5V/1.2A)…..…1
Optical fiber light guide rod (Ø 11>8 mm)…………………………………1
Filter……………………………………………………………………………1
Anti-glare shield………………………………………………………………2
Light guide sleeves…………………………………………………………20
Curing light sleeves…………………………………………………………10
User’s manual…………………………………………………………… …..1
LEDEXTM WL-090
LED Dental Curing Light EN
Charging the Battery:
The battery is not fully charged at shipment. Before use, please charge the
battery, charging time is about 2 hours.
1. Connect the power supply to AC100~240V electronic socket and plug-in
connector to cradle. Put hand piece into cradle to charge battery.
2. When the battery is in low status, the display of handpiece will glow
showing battery low sign. Refer to figure 1.
3. When the battery is fully charging, the display of handpiece will glow
showing battery full sign. Refer to figure 2.
4. When the battery is charging, the display of handpiece will glow showing
battery charge sign. Refer to figure 3.
STANDARD
STANDARD
STANDARD
40
40
40
Figure 1
Figure 2
Figure 3
LEDEXTM WL-090
LED Dental Curing Light EN
Turn on handpiece:
Push the “
“ on/off button to turn on the LEDEX
TM
WL-090 handpiece.
Output / Interrupt the light:
When the status of handpiece is turning on, push the “
to output the light.
“ on/off button again
During the exposure time, the specialist can push “ “ on/off button to interrupt
the light. Then the system will generate one beep and reset the time
automatically.
Change the mode format:
Push the “M“ mode button, the mode can be changed:
LOWRAMPSTANDARDHIGHFAST ORTHOTURBOLOW....
Change the timer format:
Push the “T“ timer button, the time can be changed:
LOW mode: 10203040102030….
RAMP mode: 51015202530354051015….
STANDARD mode: 51015202530354051015….
HIGH mode: 246810246….
FAST ORTHO mode: 34534….
TURBO mode: 2345234….
LEDEXTM WL-090
LED Dental Curing Light EN
Recommend for use:
LOW mode:
Ideal for curing bonding material that is between tooth and composite resin.
RAMP mode:
Ideal for curing the wide area of composite resin, it can avoid shrinkage.
STANDARD mode:
It is a stable output, ideal for most cases.
HIGH mode:
Ideal for orthodontic or pediatric dentistry, it can save time.
FAST ORTHO mode:
Ideal for orthodontic, it is easy to bond materials and saving time.
TURBO mode:
Ideal for non-vital tooth, or such as dental cement, porcelain veneer, fiber post
in endodontic fields.
LEDEXTM WL-090
LED Dental Curing Light EN
Auto sleep designed:
TM
LEDEX WL-090 will sleeps automatically if no operations are performed for
three minutes, the display will be turn off.
Safety mode:
TM
Whenever the LEDEX WL-090 is operated frequently and/or for long periods
of time, however, the temperature may become too high and the “Safety” mode
function will then be automatically activated to protect the light. Safety mode
cuts the light intensity in approx. half and extends the irradiation time. Refer to
figure 1.
When the temperature become quite high, the display of handpiece will glow
showing “Over Heat” sign. Refer to figure 2.
While TURBO mode was be selected, it needs enough power of battery just
can make a turbo light output. If the status of battery power is not enough to
turn on TURBO mode, the “Adaptive” mode function will then be automatically
activated to turn on the light, it cuts the light intensity in approx. half and
extends the irradiation time. Refer to figure 3.
STANDARD
s
32
Figure 1
LEDEXTM WL-090
TURBO A
Over
Heat
Figure 2
4
Figure 3
LED Dental Curing Light EN
Intensity check:
A built-in radiometer is including in cradle. While the cradle gets electric power
from power supply, output the light into the test area, the radiometer will show
the intensity of light.
LOW mode…...................................................Approx. 600
RAMP mode….……………………………….. Approx. 1000
STANDARD mode……………………………..Approx. 1000
HIGH mode……………………………………..Approx. 1800
FAST ORTHO mode…………………………..Approx. 1800
TURBO mode…………………………………..Approx. 2400
2
mW/cm (+/-15%)
2
mW/cm (+/-10%)
2
mW/cm (+/-10%)
2
mW/cm (+/-10%)
2
mW/cm (+/-10%)
2
mW/cm (+/-10%)
2
If result of intensity test in STANDARD mode is under 700 mW/cm , the output
is too low, please contact with your dealer, we will check your light.
Clean and disinfection:
The plastic of the handpiece, cradle and filter may be cleaned with a wet cloth,
while the optical light guide rod may be cleaned with alcohol or put it in
autoclave for disinfection. Suggestion is to use autoclave 134˚C/75 psi for
maximum result. The disinfection time at 134˚C should be 5 minutes. A
disposable curing sleeve available from your dealer may be used as protection
over the optical light guide rod without loss of light intensity. The applicant will
(or have) validate the sterilization procedure according to ISO 17665-1.
LEDEXTM WL-090
LED Dental Curing Light EN
Warranty:
DENTMATE TECHNOLOGY Co., Ltd. warrants the product to be free of
manufacturing defects for a period of 1 year from date of purchase, this being
deemed the date of the invoice. It will repair or replace at its own discretion all
equipment failures due to manufacturing defects. The following are however
expressly excluded from the warranty:
1. Damage and/or failure of the equipment caused by falling and/or jolting
during transportation after purchase and/or during normal use.
2. Damage and/or failure of the equipment caused by natural disasters such
as but not limited to earthquakes, floods, lightning, pollution, incorrect
electrical voltage and voltage spikes.
Do not attempt to open the hand piece as doing so will invalidate the warranty.
LEDEXTM WL-090
LED Dental Curing Light EN
Specifications:
Dental Curing Light
Device Name
Model Number
Power supply
Battery
Light source
The range of wavelength
Radiant intensity
Hand piece size
Hand piece weight
Cradle size
Cradle weight
Medical equipment
TM
LEDEX
WL-090
Input: AC100~240V, 50/60Hz
Output: DC 5V/1.2A
3.7V, 2500mAh, type: Lithium-ion
10W Dental blue LED
440 to 480 nm
2
600 to 2400 mW/cm
Ø 38 mm(max.) x L 190 mm
180 g
Ø 115 mm(max.) x H 68 mm
140 g
Troubleshooting:
Situation
Troubleshooting
Do not turn on the handpiece
Remove and reinsert Battery. If the error
persists, please plug-in the power supply to
cradle and charge the battery at least 10 min.,
then push the ON/OFF button again.
Do not charge the battery
Please clean battery contacts. If the error
persists, please change a new battery.
Display show overheat sign
The temperature rises up to high really. Please
wait a moment and then use it again.
The intensity is too low
If result of intensity test in Standard mode is
2
under 700 mW/cm , the output is too low,
please contact with your dealer.
LEDEXTM WL-090
European Authorized Representative:
TOPDENTAL (PRODUCTS) LTD.
12 Ryefield Way, Silsden,
West Yorkshire, BD20 0EF, UK
TEL: +44 (0)1535 652 750 FAX: +44 (0)1535 652 751
WEBSITE: www.topdental.org
EMAIL: [email protected]
DENTMATE TECHNOLOGY CO., LTD.
8F, No. 8-11, Sec. 1, Zhongxing Road,
Wugu District, New Taipei City 24872, Taiwan
TEL: +886 2 8976 9226 FAX:+886 2 8976 9236
WEBSITE: www.dentmate.com.tw
EMAIL: [email protected]
2014/01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement