PDF Manual

PDF Manual
1. Part list
`
3.5V Coaxial Ophthalmoscope
User’s Guide
1
8
7
2
6
3
4
5
`
Thank you for purchasing the 3.5V coaxial
ophthalmoscope. To prevent damage to the 3.5V coaxial
ophthalmoscope or injury to yourself or to others, read
the following safety precaution in their entirety before
using this device. Keep these safety instructions where
all those who use the device will read them.
1.
Fig. 1
Polarizing filter / red-free filter switch;
2.
Aperture selection dial;
3.
Diopters selection disc;
4.
Bulb;
5.
Dowel pin of bulb;
6.
Illuminated Diopters indicator;
7.
Peep hole;
8.
Rubber brow rest;
2. Operating Instructions
a) Connect the 3.5V Coaxial Ophthalmoscope to the
power.
b) For examination of the right eye, sit or stand at the
patient’s right side.
c) Select “0” on the illuminated lens disc of the
Attention. Read user’s guide for cautions and
ophthalmoscope and start with the small aperture.
instructions for operating.
d) Take the ophthalmoscope in the right hand and hold it
Warnings and Cautions
vertically in front of your own right eye with the light
beam directed toward the patient and place your right
index finger on the edge of the lens dial so that you
Warning: This product must not be used in the
presence of flammable gases.
will be able to change lenses easily if necessary.
e) Dim room lights. Instruct the patient to look straight
ahead at a distant object.
Warning: This product should not be immersed
f) Position the ophthalmoscope about 6 inches (15 cm)
in fluids.
in front and slightly to the right (25°) of the patient
and direct the light beam intothe pupil. A red “reflex”
Warning: Use 3.5V Coaxial Ophthalmoscope
only with all approved 3.5V power.
should appear as you look through the pupil.
g) Rest your left hand on the patient’s forehead and
hold the upper lid of the eye near the eyelashes with
Warning: Federal law restricts this device to sale
or order of a physician.
the thumb. While the patient is fixating on the
specified object, keep the “reflex” in view and slowly
move toward the patient. The optic disc should come
into view when you are about 1 to 2 inches (3-5 cm)
from the patient. If it is not focused clearly, rotate
lenses with your index finger until the optic disc is as
clearly visible as possible. The hyperopic, or
1
far-sighted, eye requires more “plus” (green numbers)
Caution: The 3.5V Coaxial Ophthalmoscope
lenses for clear focus of the fundus; the myopic, or
should never be placed in municipal waste.
nearsighted, eye requires minus” (red numbers) lenses
for clear focus.
h) Now examine the disc for clarity of outline, color,
4.Technical Specifications
elevation and condition of the vessels. Follow each
vessel as far to the periphery as you can. To locate the
Optical Specification
macula, focus on the disc, then move the light
approximately 2 disc diameters temporally. You may
Diopter
0D, ±1D, ±2D, ±3D, ±4D, ±5D,
±6D,±7D, ±8D, ±9D, ±10D, +12D,
±15D, ±20D,-25D,+40D
Aperture
Large aperture,
small aperture,
Micro aperture,
Slit aperture,
Cobalt blue aperture,
Fixation aperture.
Filter
Red free filter / Polarizing filter
Bulb
3.5 V
Operation mode
Intermittent, On-time should not
exceed 2 mins with Off-time not less
than 5 mins
also have the patient look at the light of the
ophthalmoscope, which will automatically place the
macula in full view. Look for abnormalities in the
macula area. To examine the extreme periphery,
instruct the patient to:

Look up for examination of the superior retina

Look down for examination of the inferior retina

Look temporally for examination of the temporal
retina

Look nasally for examination of the nasal retina.
2.7 W
This routine will reveal almost any abnormality
Environment requirements
that occurs in the fundus.
i) To examine the left eye, repeat the procedure outlined
above but hold the ophthalmoscope in
red-free filter
Operation
facilitates viewing of the center of the macula.
3.Maintenance
3.1
Shipping
Replacing the illumination bulb
Turn off the main power switch, remove the 3.5V coaxial
Storage
cphthalmoscop from the power . grasp end of bulb and pull
out. Insert replacement bulb, Push bulb in firmly.
The
specification
of
bulb
for
the
3.5V
Coaxial
Ophthalmoscop is 3.5V/2.7W .
Fig.2
Cleaning
The cleaning of the 3.5V Coaxial Ophthalmoscope is easily
accomplished by wiping the external surface with a cloth
dampened with a mild detergent and water solution, or a
41092.000.00. N0
3.2
70% isopropyl alcohol, or a 10% bleach solution (by
volume). Do not immerse.
NOTE: Solution entering the assembly could damage
internal components. Use caution to ensure cloth is not
saturated with solution.
2
Environment Temperature
+10 ℃…+35 ℃
Relative Humidity
30%…75%
Atmospheric Pressure
700 hPa…1060 hPa
Common Conveyance
Environment Temperature
-40 ℃…+55 ℃
Relative Humidity
10%…90%
Atmospheric Pressure
500 hPa…1060 hPa
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement