eKEY™ for iPhone User Manual

eKEY

™

for iPhone

User Manual

Copyright © 2010 UTC Fire & Security. All rights reserved.

Rev 02 April 2011

Disclaimer The information in this document is subject to change without notice. UTC Fire & Security

(“UTCFS”) assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. For the latest documentation, contact Supra or visit us online at

www.supraekey.com

.

Trademarks and patents

This publication may contain examples of screen captures and reports used in daily operations.

Examples may include fictitious names of individuals and companies. Any similarity to names and address of actual businesses or persons is entirely coincidental.

Supra, eKEY, and iBox are registered trademarks of UTC Fire & Security. iPhone is a trademark of

Apple, Inc., registered in the U.S. and other countries. Google Maps is a trademark of Google Inc.

Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose it was designed for. For the latest product information, contact Supra or visit us online at

www.supraekey.com

.

Rules and regulations relating to the use of the service

Key Possession. Each keyholder (“Keyholder”) is responsible for the key (“Key”) issued to him or her.

Current Update. The Key must be updated in order to access keyboxes (“Keyboxes”). The Key cannot be updated unless the Keyholder is in good standing with the organization (“Organization”) and UTC Fire & Security, Americas Corp. (“UTCFS”), is authorized to use the Service, and is in compliance with the obligations for the use of the Service including, without limitation, these rules and regulations.

Equipment Security. It is necessary to maintain the security and the personal identification number

(“PIN”) of the Key to prevent the use of the Key and the Service by unauthorized persons. Each person in possession of a Key, whether such Key is being actively used or not, shall abide by the following terms and conditions:

To keep the Key in authorized Keyholder’s possession or in a safe place at all times;

Not to allow the PIN for the Key to be displayed on or attached to the Key for any purpose whatsoever or to be disclosed to any third party;

Not to lend or otherwise transfer the Key to any other person or entity, or permit any other person or entity to use the Key for any purpose whatsoever, whether or not such other person or entity is authorized to use the Key;

Not to duplicate the Key or allow any other person to do so;

Not to assign, transfer or pledge the Key;

Not to (i) destroy, alter, reproduce, modify, adapt, translate, reverse engineer, de-compile, disassemble or tamper with the Key or knowingly or unknowingly allow anyone else to do so; or (ii) provide or otherwise make available the software or any part or copies thereof to any third party;

To notify your Organization or UTCFS within forty-eight (48) hours if the Key is lost or stolen;

To follow all additional security procedures as specified by your Organization; and

To safeguard the code for each Keybox from all other individuals and entities, whether or not they are authorized users of the service.

Keybox Authorization. Before a Keybox is installed or used on any piece of real property, the prior written authorization to install or use a Keybox must be obtained from the property owner, as well as from any tenant(s) in possession of the property, if applicable. Extreme care shall be used to ensure that all doors to the listed property and the Keybox are locked. All owners and/or tenant(s) of real property shall be informed that the Keybox is not designed to be, or intended as, a security device.

ii

Contents

Rules and regulations .......................................................................................................ii

Preface ................................................................................................................................v

Safety Terms and Symbols ........................................................................................... v

Chapter 1 Introduction ....................................................................................1

Overview .............................................................................................................................2

Requirements ............................................................................................................... 2 eKEY Software ............................................................................................................. 2 eKEY Adapter ............................................................................................................... 3

SupraWEB .................................................................................................................... 3

KIMvoice ....................................................................................................................... 3

eKEY Setup .........................................................................................................................4

Install eKEY Software ................................................................................................... 4

Authorize eKEY ............................................................................................................ 5

Customize PIN .............................................................................................................. 5

Audio and Vibrate Settings ........................................................................................... 6

Chapter 2 Updating ..........................................................................................8

Updating .............................................................................................................................9

Manual Update ............................................................................................................. 9

Disable Automatic Update .......................................................................................... 11

Chapter 3 Accessing iBoxes.........................................................................12

Accessing iBoxes ............................................................................................................13

Supra eKEY Adapter ................................................................................................... 13

Release the Key Container ......................................................................................... 14

Place Listing Keys in the iBox..................................................................................... 15

Feedback .................................................................................................................... 15

Showing Hours ........................................................................................................... 16

Call Before Showing (CBS) ........................................................................................ 16

Cooperating ................................................................................................................ 17

Release the Shackle .................................................................................................. 17

Remove the Shackle ................................................................................................... 18

iBox Inventory ..................................................................................................................19

View iBox Inventory and Detail Information ................................................................ 19

Add Keybox to your Inventory..................................................................................... 19

Delete an iBox from your Inventory ............................................................................ 20

Read Activity ............................................................................................................... 21

View Showing Activity ................................................................................................. 22

Change iBox Settings ................................................................................................. 22

Chapter 4 MLS Listings and Roster .............................................................25

eKEY Professional ...........................................................................................................26

Settings for eKEY Professional ................................................................................... 26

Listings .............................................................................................................................28

Market Area ................................................................................................................ 28

Update Listings ........................................................................................................... 29 iii

View Listings ............................................................................................................... 29

Delete Listings ............................................................................................................ 36

Roster ................................................................................................................................37

View Roster ................................................................................................................ 37

Delete Roster .............................................................................................................. 38

Chapter 5 Showing Activity ..........................................................................39

Showing Activity ..............................................................................................................40

Voice Report ............................................................................................................... 40

Showing Notifications Messages ................................................................................ 40

Showings Activity on iPhone ....................................................................................... 42

Disable eKEY Showing Notifications .......................................................................... 43

Update Listing ID ........................................................................................................ 43

Chapter 6 Support and Troubleshooting .....................................................44

Support .............................................................................................................................45

Training Library ........................................................................................................... 45

Help Screens .............................................................................................................. 46 iv

Preface

This is the eKEY for iPhone User Manual. This document includes an overview of the product and detailed instructions explaining:

• how to set up your eKEY software;

• how to update your eKEY to access an iBox;

• how to access iBoxes;

• how to view MLS listing and roster data; and

• how to view showing activity.

There is also information describing how to contact technical support if you have questions or concerns.

For specific information about your iPhone, refer to the documentation that was provided with your iPhone. For additional information on using your Supra eKEY software, visit

www.supraekey.com

and click on the Training Resources link.

The following conventions are used in this document:

Bold

Italic

Blue italic

Monospace

Menu items and buttons.

Emphasis of an instruction or point; special terms.

File names, path names, windows, panes, tabs, fields, variables, and other GUI elements.

Titles of books and various documents.

(Electronic version.) Hyperlinks to cross-references, related topics, and URL addresses.

Text that displays on the computer screen.

Programming or coding sequences

Safety Terms and Symbols

These terms may appear in this manual:

CAUTION: Cautions identify conditions or practices that may result in damage to the equipment or other property.

v

Chapter 1

Introduction

1

Chapter 1 Introduction

This chapter provides an overview of the eKEY software and explains how to set up your eKEY software.

In this chapter:

Overview .................................................................................................. 2

Requirements ..................................................................................... 2

eKEY software ..................................................................................... 2

eKEY Adapter ...................................................................................... 3

SupraWEB ........................................................................................... 3

KIMvoice .............................................................................................. 3

eKEY Setup .............................................................................................. 4

Install eKEY Software .......................................................................... 4

Authorize eKEY ................................................................................... 5

Customize PIN..................................................................................... 5

Audio and Vibrate Settings .................................................................. 6

Chapter 1

Introduction

Overview

The eKEY software and eKEY Adapter allow you use your iPhone to access Supra iBoxes placed at real estate listings.

2

Requirements

• iPhone, iPhone 3G, iPhone 3GS, iPhone 4, iPad 3G, or iPad 2 3G

• OS 3.1.3 or greater

• Data plan on your iPhone through your cellular provider

• Supra eKEY Adapter for iPhone

eKEY Software

The eKEY software for iPhones allows you to:

• Obtain the listing keys from an iBox

• Open the shackle on a iBox to place it on a listing or remove from a listing

• Manage and view your iBox inventory and change iBox settings

• Read an iBox to view showing history

• View showing notices and messages

• View MLS information and roster — for eKEY Professional subscribers only

Figure 1. eKEY Basic Home screen

Chapter 1

Introduction

The eKEY software connects regularly to the Supra network using your cellular Internet service. During the connection, the eKEY software sends showing data to the Supra network, updates the eKEY to access iBoxes, and receives messages and showing notifications. During the first eSYNC of each day, the MLS listing and roster data is updated if you subscribe to eKEY Professional.

3

eKEY Adapter

The Supra eKEY Adapter provides an infrared signal from your iPhone that can be received by an iBox. The Supra eKEY Adapter has a key ring for easy placement on your key chain, a connector that connects to your iPhone, and an infrared lens used for communicating with iBoxes.

SupraWEB

SupraWEB is the agent website, available at

www.supraekey.com

where you can go to:

• Obtain an update code for your key

• Identify the name of a keyholder by key serial number

• Manage your iBox inventory and listing information

• View, email, and schedule activity reports

• View and send showing feedback

• Manage your bill

• Change your PIN code

• Set up your market area (eKEY Professional subscribers)

• Obtain an authorization code for installing eKEY software

SupraWEB can also be accessed using your iPhone by opening the eKEY application and selecting the

SupraWEB icon on the second page.

KIMvoice

KIM, the Keybox Information Manager, is the Supra network that maintains the key and keybox data.

Automated voice access to KIM is available by calling 888-968-4032.

Chapter 1

Introduction

eKEY Setup

This section explains how to install the eKEY software onto your iPhone and authorize the applications.

4

Install eKEY Software

The eKEY software is installed through the App Store. You must have an iTunes account set up through

Apple in order to install the Supra eKEY software.

To install the eKEY software on your iPhone:

1. On your iPhone, launch the App Store by selecting the App Store icon.

2. Select Search and search for Supra eKEY.

3. Select the Supra eKEY application.

4. Select the FREE button and then select INSTALL.

5. Enter your iTunes password and click OK.

Once the software is installed, the eKEY icon is shown in the list of applications on your iPhone.

Figure 2. eKEY icon

Chapter 1

Introduction

Authorize eKEY

Once the eKEY software is installed, it must be authorized before it can be used. To authorize the eKEY software, you’ll need your 30-digit Authorization code.

New eKEY users can obtain an authorization code from the Association/Board/MLS. Existing eKEY users can obtain an authorization code by logging into SupraWEB and selecting the

Authorization

Code link.

Demo mode is available for customers who have not yet subscribed to eKEY service. Demo mode allows you to view the eKEY software but you cannot interact with iBoxes.

To authorize your eKEY software:

1. Launch the eKEY application by selecting the eKEY icon.

2. Select Activate eKEY.

3. Following the onscreen prompts, enter your 30-digit Authorization code.

4. Select Authorize.

5

Figure 3. Authorize eKEY screen

5. Your device will automatically connect and authorize and update the eKEY to access iBoxes.

Customize PIN

You can customize the PIN code you use with your eKEY software.

Chapter 1

Introduction

To customize your PIN:

1. On your computer navigate to

www.supraekey.com

.

2. Select Agents-Log on to SupraWEB.

3. Enter your user ID and password and select Submit. If you haven’t registered for a single sign on (SSO) user ID and password yet, click the How to get access link to register for a login.

4. Select Change PIN.

6

Figure 4. Change PIN Code screen

5. Enter your current PIN code.

6. Enter the new PIN code you would like to use and re-enter to confirm.

7. Click Save.

8. On your iPhone, select the eKEY icon to open the eKEY application.

9. Select Update.

10. Select Wireless Update to do a wireless manual update.

Audio and Vibrate Settings

The eKEY software uses several audio tones along with messages on the screen to communicate the status of keybox operations and to alert you when you receive a new showing or message. If an error occurs, your iPhone will vibrate in addition to sounding a buzz tone.

The audio and vibrate feedback in the eKEY software can be disabled. Disabling the audio or vibrate feedback in the eKEY software does not affect other iPhone applications.

To disable the audio or vibrate in the eKEY software:


2. Select Settings.

Note: If you have eKEY Professional, the Settings icon is on the second page of icons.

3. Set the Audio Feedback or Vibrate Feedback option.

4. Select Home to return to the eKEY main screen.

Figure 5. Disable Audio or Vibrate Feedback

Chapter 1

Introduction

7

Chapter 2

Updating

8

Chapter 2 Updating

This chapter explains how to update your eKEY software.

In this chapter:

Updating ................................................................................................... 9

Manual Update .................................................................................... 9

Disable Automatic Update ..................................................................11

Chapter 2

Updating

Updating

Updating the eKEY software allows your iPhone to access iBoxes.

The eKEY software expires each night at midnight. The eKEY software automatically updates the first time each day when the eKEY application is launched by connecting to the Supra network using your smartphone’s cellular or WiFi service.

In order for an update to occur, your iPhone needs to be in cell coverage and you need to be in good standing with your Organization and with Supra.

You can see if your eKEY software is expired when you open the eKEY application. The Update icon shows a red X through the icon when the eKEY software is expired.

9

Figure 6. Key Expired icon for eKEY Basic main menu and eKEY Professional main menu

If your eKEY software did not update because the automatic update is turned off in your eKEY software, the next time you press the Obtain Key, Open Shackle, Add Keybox, Read Activity, or Update icons, you will be prompted to do a wireless update or enter an emergency update code.

Manual Update

If your eKEY software is expired and you are in cell coverage, you can do a wireless manual update.

1. Select the eKEY icon to open the eKEY application.

2. Select Update (see figure 7 on page 10).

3. Select Wireless Update to do a wireless manual update.

If your eKEY software is expired and you are out of cell coverage, you can manually update by obtaining and entering an update code.

Chapter 2

Updating

To obtain an update code from SupraWEB:

1. Go to

www.supraekey.com

and click Agents-Log on to SupraWEB.

2. Enter your user ID and password and click Submit.

3. Select the Update Code link under Quick Links. The update code displays.

To obtain an update code from KIMvoice:

1. Call KIM at 1-888-968-4032.

2. When prompted, enter your eKEY serial number and PIN code into the phone, followed by the # sign.

3. Press 1 on the phone for an update code.

To enter the update code into the eKEY software:


2. Select Update.

3. Select Emergency Update Code.

4. Enter the update code.

10

Figure 7. Enter Update Code

The number of consecutive update codes you can get is limited. Once you reach your update code limit, your eKEY software must do a wireless update before you can obtain any additional update codes.

Chapter 2

Updating

Disable Automatic Update

You can turn off the automatic key update. If you disable the automatic key update, be sure to update your eKEY software before going out to a listing To disable the automatic key update:




3. Turn the Automatic Update option off.

4. Select Home to return to the eKEY menu.

11

Figure 8. Disabling Automatic Updates

In addition to the automatic update the first time the eKEY software is launched each day, the eKEY software automatically updates and sends showing information immediately after each key container opening and shackle release.

Chapter 3

KeyBoxes

12

Chapter 3 Accessing iBoxes

This chapter explains how to access and manage iBoxes and gives information on Call Before Showing (CBS) and accessing cooperating keybox systems.

In this chapter:

Accessing iBoxes .................................................................................. 13

Supra eKEY Adapter ......................................................................... 13

Release the Key Container................................................................ 14

Place Listing Keys in the iBox ........................................................... 15

Feedback ........................................................................................... 15

Showing Hours .................................................................................. 16

Call Before Showing (CBS) ............................................................... 16

Cooperating ....................................................................................... 17

Release the Shackle ......................................................................... 17

Remove the Shackle ......................................................................... 18

iBox Inventory ....................................................................................... 19

View iBox Inventory and Detail Information ....................................... 19

Add Keybox to your Inventory ........................................................... 19

Delete an iBox from your Inventory ................................................... 20

Read Activity ...................................................................................... 21

View Showing Activity ........................................................................ 22

Change iBox Settings ........................................................................ 22

Accessing iBoxes

The eKEY software allows you to access Supra iBoxes to:

• release the key container

• release the shackle

• change the settings in your iBoxes

• read the showing history stored in a iBox

Figure 9. Supra iBoxes

shackle infrared lens shackle infrared lens

Chapter 3

KeyBoxes

13 iBox BT iBox

The iPhone communicates with the iBox and iBox BT using infrared technology. You’ll need the Supra eKEY adapter to access iBoxes with your iPhone. The eKEY adapter translates the signal from your iPhone into an infrared signal that can be understood by the iBox. The distance between the eKEY adapter and the infrared lens on the iBox should be less than a foot. Direct sunlight can interfere with the infrared communication, so you may need to shade the area between the eKEY adapter and the iBox.

Supra eKEY Adapter

In order to communicate with iBoxes, the Supra eKEY Adapter must be connected to your iPhone. The eKEY Adapter enables the eKEY software to communicate with an iBox.

To interact with iBoxes, connect your eKEY Adapter to your iPhone. The eKEY Adapter does not have to be connected to your iPhone when you are not accessing iBoxes.

When prompted by the eKEY software, point the infrared port on the eKEY Adapter towards the infrared lens on the iBox.

Tip: When the eKEY Adapter and iBox are communicating, they should be less than foot between your eKEY Adapter and the iBox Direct sunlight can interfere with infrared communication so you may need to shade the area between the eKEY Adapter and iBox when they are communicating.

Chapter 3

KeyBoxes

14

Figure 10. Supra eKEY Adapter

Key ring for easy placement on key chain cap iPhone connector

Infrared port

Release the Key Container

To release the key container on an iBox when showing a listing or placing or removing the listing keys in an iBox:


2. Select Obtain Key.

3. Enter your PIN code.

4. Connect your eKEY Adapter to your iPhone if it’s not already connected and select Begin.

5. Point the infrared port on the eKEY Adapter at the infrared lens on the iBox.

Note: You have 5 minutes after pressing Begin before you have to aim the eKEY Adapter at the iBox. This gives you an opportunity to enter your PIN in the car and then walk up to the door.

Figure 11. Obtain Key

Chapter 3

KeyBoxes

6. Upon success, press up on the bottom of the iBox to release the key container. The key container will relock after 30 seconds.

7. If a business card, agent notes, or a listing flyer has been programmed into the iBox, the information displays on your iPhone. Drag down to see any additional information.

Your iPhone connects to the network and sends the showing information immediately after you obtain a key.

15

Place Listing Keys in the iBox

Before closing the key container, verify that all items are well inside and that the front is not bowing or bulging out. If you are a listing agent, always make sure that you have a spare set of listing keys before you close the key container.

Caution: Do not place ID tags, key rings, or loose objects in the key container. They can jam the container.

To close the key container, turn it so the compartment holding the keys is facing you. Insert the key container into the bottom of the iBox and push up until it closes.

Feedback

A feedback alert screen is displayed after the key container opens if the iBox is set to ask for feedback after a listing is shown. This gives you an opportunity to provide feedback about the showing to the listing agent.

If you select Ignore, no feedback will be sent to the listing agent.

Select Leave Feedback to enter feedback information to send to the listing agent. You can select where you heard about the listing, the level of interest in the property, whether the listing price is within the buyer’s range, and you can enter any notes about the showing.

Figure 12. Leave Feedback

Chapter 3

KeyBoxes

The feedback is delivered to the Supra network the next time your eKEY software updates. The listing agent can view the feedback at SupraWEB.

Only the listing agent can activate or deactivate the feedback setting in an iBox. (See

Change iBox

Settings

on page 22 for more information.)

16

Showing Hours

iBoxes can be programmed to allow 24-hour access or timed access for specific hours. To determine the timed access hours preprogrammed into iBoxes in your area, contact your Association or MLS.

Showing hours are in standard time. If your area observes daylight saving time, the actual access hours are one hour later than the hours set in the iBox during daylight saving time. For example, if an iBox is programmed for access from 8 a.m. to 9 p.m. Standard Time, during daylight saving time, the actual showing hours are 9 a.m. to 10 p.m.

You can program your iBoxes to allow 24-hour access or to limit access to during the timed access hours. You can also customize the showing hours and set different access hours for weekdays,

Saturday, and Sunday.

Follow the instructions on

Change iBox Settings

on page 22 to change the iBox showing hours.

Call Before Showing (CBS)

Call Before Showing (CBS) allows the listing agent to control access by requiring the showing agent to call the listing agent to obtain a CBS code.

Every iBox contains a Call Before Showing (CBS) code that can be enabled (see

Change iBox Settings

on page 22 for more information). This code must be entered into the showing agent’s key to open the iBox. Contact the listing agent to determine if a CBS code is required to open an iBox.

If the iBox requires a CBS code, the code must be entered into the eKEY software before releasing the key container and it must be entered each time the key container is released. (See

Release the Key

Container

on page 13 for more information.)

To open an iBox that requires a CBS code:

1. Follow the obtain key steps (see

Release the Key Container

on page 13 for more information).

2. If CBS is required, an error tone sounds and the CBS Required screen pops up. Enter the CBS code and select Continue.

Note: If you prefer to enter the CBS code before pointing the eKEY adapter at the iBox, you can turn on Enable CBS Input in Settings and you can enter a CBS code before selecting Begin.

Chapter 3

KeyBoxes

17

Figure 13. CBS Required

Cooperating

You may be able to access iBoxes in a neighboring Association/MLS. Check with your Association/MLS to determine if your area has a cooperating agreement in place.

To show listings in a cooperating area:

• Your eKEY software must be programmed to allow access to iBoxes in the cooperating area

• The cooperating Association/MLS must give you permission to update your eKEY for their area

Your Association/MLS can give you permission to access cooperating areas into your eKEY software.

Once the programming has been added to your eKEY software, contact the cooperating Association/

MLS to receive permission to update your eKEY software for their system.

Once both of those steps are completed, when your eKEY software does an automatic update, it updates both your primary system and the cooperating system. If you manually update your eKEY software by entering an update code, you must first update it for your primary Association/MLS and then update it for cooperating areas.

Release the Shackle

Each iBox has a four-digit shackle code that is used to release the shackle for placing it at a listing or removing it from a listing.

To release the shackle on an iBox:


2. Select Open Shackle.

3. Enter the shackle code.

Chapter 3

KeyBoxes

4. Connect your eKEY Adapter to your iPhone if it’s not already connected and select Begin.

5. Point the infrared port on the eKEY Adapter at the infrared lens on the iBox or iBox BT.

18

Figure 14. Open Shackle

6. For an iBox, the shackle pops open. To remove the shackle completely, repeat steps 1 through

5 in the above section while providing upward pressure on the shackle so it can pop out of the iBox.

For an iBox BT, press down on the shackle with one hand while supporting the bottom of the iBox BT with the other hand. Then pull up on the shackle to remove it completely from the iBox

BT.

7. Upon success, the shackle releases and the battery level in the iBox is shown.

When you release the shackle on an iBox, the iBox is automatically added to your inventory and you are taken to the Keybox Details screen where you can edit the settings in the iBox unless you uncheck

Add to Inventory. Immediately after releasing the shackle the iPhone connects to the network and sends the current inventory information about the iBox. (See

iBox Inventory

below for more information about your keybox inventory.)

Chapter 3

KeyBoxes

19

iBox Inventory

You can view your iBox inventory by selecting the Inventory icon on the main eKEY screen.

View iBox Inventory and Detail Information


2. Select Inventory.

3. A list of your keyboxes are displayed. If the keybox is assigned to a listing, the listing ID number is shown in bold above the keybox serial number.

4. Select a keybox from the list to view detailed information.

Figure 15. View iBox Inventory

Add Keybox to your Inventory

Adding a keybox to your inventory allows you to receive real time showing notifications on your iPhone and edit the settings in the keybox. You must have the keybox present to add it to your inventory.

When you release the shackle on an iBox, the iBox is automatically added to your inventory unless you uncheck Add to inventory.

To add a keybox to your inventory:


2. Select Add Keybox.

3. Enter the shackle code for the iBox.

Chapter 3

KeyBoxes

20

Figure 16. Add Keybox

4. Connect your eKEY Adapter to your iPhone and select Begin.

5. Point the infrared port on the eKEY Adapter at the infrared lens on the iBox.

The iBox has now been added to your inventory on your eKEY software. The iBox will be added to your inventory at SupraWEB during the next key update. To immediately update your keybox inventory at

SupraWEB:

1. Press Done to go to the Keybox Details screen.

2. Press Home to return to the main eKEY screen.

3. Select the Update icon to update your keybox inventory at SupraWEB.

Once the key has completed the update, the new iBox will have been added to your inventory on

SupraWEB.

Delete an iBox from your Inventory

To delete an iBox from your inventory:



3. Select the iBox from the list.

4. Select Delete.

Chapter 3

KeyBoxes

21

Figure 17. Delete Keybox

5. Select Yes to confirm.

The iBox has now been deleted from your inventory on your eKEY software. The iBox will be deleted from your inventory at SupraWEB during the next key update. To immediately delete the iBox at

SupraWEB:

1. Press the back arrow to return to the main eKEY screen.

2. Press the Menu button.

3. Select Update Key from the list to update your iBox inventory at SupraWEB.

Once the key has completed the update, the iBox will have been deleted from your inventory at

SupraWEB.

Read Activity

The iBox stores a showing record each time the key container is released. The iBox records the date and time the property was shown and the showing agent’s name, key serial number, and phone number. You can view the showings that are stored in an iBox and display them on your iPhone by reading the iBox activity.

To read an iBox:


2. Select Read Activity.

3. Enter the shackle code for the iBox.


5. Point the infrared port on the eKEY Adapter at the infrared lens on the iBox. The showings in the iBox are read and delivered to your iPhone. The number of showings in the iBox are displayed.

6. Select Done to view the showings.

7. Select a showing to view detailed information about the showing.

8. Select the phone number to call the showing agent.

Figure 18. Keybox Activity

Chapter 3

KeyBoxes

22

View Showing Activity

Once an iBox has been read, the showing activity is stored in the iBox and can be viewed at any time.

To view showing activity:



3. Select the iBox from the list.

4. Select Activity.


Change iBox Settings

You can change the settings of an iBox that is in your inventory. (See

Table 1

on page 23 for the settings you can change in an iBox.) The iBox needs to be present to save the new settings to it.


2. Select Inventory. A list of the keyboxes in your inventory displays.

3. Select a keybox from the list to view the keybox’s settings. If the keybox you are looking for is not in your inventory, see

Add Keybox to your Inventory

on page 19 for more information.

Chapter 3

KeyBoxes

4. Select the field you want to change and then update the information. A gold star to the left of the field indicates a change has been made to the setting that has not been updated in the keybox.

23

Figure 19. Change iBox Settings

5. Select Program.

6. Enter the shackle code for the iBox. If you are changing the shackle code, you’ll need to enter the old shackle code one last time here.


8. Point the infrared port on the eKEY Adapter at the infrared lens on the iBox to have the new settings updated in the iBox.

9. Once the programming has completed, your screen will show your updated values.

Chapter 3

KeyBoxes

24

Table 1. Keybox settings and description

Setting

Shackle code

Description

Code used to release the shackle on the keybox

Require Feedback Prompt for feedback after a showing

Require CBS Turn on to require a CBS code be entered to open the keybox

Timed Access Toggle between 24-Hour and Timed Access hours

Access Hours If Timed Access is on, can adjust hours for weekdays, Saturdays, and Sundays

Listing Information Information about the listing; update the listing ID, listing date, address, MLS name, client, and occupant

Business card

Agent Note

Listing agent’s business card information; displayed to eKEY users when they open the iBox

Notes to the showing agent; displayed to ActiveKEY and eKEY users when they open the iBox

Listing Flyer Features or information about the listing; displayed to eKEY users when they open the iBox

Chapter 4

MLS Data

25

Chapter 4 MLS Listings and Roster

This chapter explains how to set up your market area, search and view listings, create saved searches, and search and view the agent roster.

In this chapter:

eKEY Professional ................................................................................ 26

Settings for eKEY Professional ......................................................... 26

Listings .................................................................................................. 28

Market Area ....................................................................................... 28

Update Listings .................................................................................. 29

View Listings ...................................................................................... 29

Delete Listings ................................................................................... 36

Roster ..................................................................................................... 37

View Roster ....................................................................................... 37

Delete Roster..................................................................................... 38

Chapter 4

MLS Data

eKEY Professional

The eKEY software allows you to view MLS listing and roster information on your iPhone. There are five additional icons on the eKEY home screen when you subscribe to eKEY Professional:

• Listings – Search and view listings

• Roster – Search and view the agent roster

• Hotsheets — View Hotsheet listings

• Showings – View showing activity for your listings; see

Chapter 5 Showing Activity

• Market Area – Define the listings to download and view on your iPhone

26

Figure 20. eKEY Professional Home screen

Important! You must subscribe to eKEY Professional service to view MLS data in the eKEY software.

Contact your Association/MLS to change your subscription.

Settings for eKEY Professional

There are some settings available only for eKEY Professional subscribers.

To view or change the eKEY Professional settings:



Note: If you have eKEY Professional, the Settings icon is on the second page of icons.

Chapter 4

MLS Data

27

Figure 21. eKEY Professional Settings

3. Set Download Listings to OFF if you no longer want to download listings to your iPhone.

4. Set Download Roster to OFF if you no longer want to download listings to your iPhone.

Chapter 4

MLS Data

Listings

With eKEY Professional service, you can view MLS listings on your iPhone. The listing information is downloaded to your iPhone during the first eKEY software update of any given day.

28

Market Area

Your market area determines which listings are downloaded and viewable on your iPhone. Before you can view listings on your iPhone, you need to define your market area. You can change your market area as often as you like.

Important! You must be in cell coverage to define your market area and download listings. Once the listings are downloaded you don’t need to be in cell coverage to view them.

Tip! Select only listings in areas you show in for your market area to speed up listing searches and updates.

If you select the Listings icon and your market area is not set up, you’ll be prompted to configure your market area.

To set up your market area:


2. Select the Market Area icon.

3. Choose your market area by selecting areas, classes, statuses, and a price range.

You must select at least one area, class, and status.

Figure 22. Configure Market Area

4. Select Save to save your market area.

5. Enter your 4-digit PIN code to save your market area and select Begin.

6. Select Download to download the listings in your market area to your iPhone.

Figure 23. Downloading Listings

Chapter 4

MLS Data

29

Update Listings

Once you have set up your market area, the listings and roster are updated when the eKEY software updates the first time each day (see

Updating

on page 9).

Important! The listings are pulled from the MLS to the Supra network daily. Updating the eKEY software more than once a day does not update.

View Listings

There are several ways to view the MLS listings in the eKEY software.

• Quick Search – Search for listings by address, zip code, or MLS ID number

• Custom Search – Search for listings that match specific criteria

• Hotsheets — View Hotsheet listings

• My Listings – View your personal listings

• Saved Searches – Create and save custom searches

Chapter 4

MLS Data

30

Figure 24. Listings Options

Quick Search

The Quick Search allows you to quickly search for listings by entering part or all of a street address or MLS ID. You can also perform a quick search by zip code if the zip code is included in the listing address.

To do a quick search of the listings in your market area:


2. Select the Listings icon.

3. Select Quick Search.

4. Enter part or all of street address or MLS ID number. The listings that match are displayed in ascending price order.

5. Select a listing to view detailed information.

Chapter 4

MLS Data

31

Figure 25. Quick Search

Hotsheet

The Hotsheet displays new listings or listings that have had a chance to their price or status in the last three days.

To display listings in your market area that are on the Hotsheet:


2. Select the Hotsheets icon. The Hotsheet listings within your market area are displayed.

Note: You can also select the Listings icon and then select Hotsheets.


Chapter 4

MLS Data

32

Figure 26. Hotsheet — New Price

Personal Listings

Personal listings displays all of your personal listings within the market area you have selected.

To display your personal listings:


2. Select the

Listings icon.

3. Select My Listings. All of your personal listings within the market area you have selected are displayed.


Custom Search

The Custom Search allows you to search for specific listings in your market area. Custom searches can also be saved.

To perform a custom search:

1. Select the

eKEY icon to open the eKEY application.


3. Select Custom Search.

4. Select the criteria for your search. Some fields allow you to choose specific criteria from a list while others allow you to select a range or input specific text. The more search criteria you select, the more specific your results will be.

Chapter 4

MLS Data

33

Figure 27. Custom Search

5. Select the search button in the upper right corner of the screen. All of the listings within the market area you have selected are displayed.


Tip: If your search returns more than 25 records, tap the Load 25 More button at the bottom of the screen.

Listing Details

Listings that match the search criteria are displayed in a list view. The listings are sorted by price in ascending order. Hotsheet listings are designated with a hotsheet icon.

Chapter 4

MLS Data

34

Figure 28. Listing Search Results

To view details about a particular listing, select the listing. Scroll down to view additional information.

Figure 29. Listing Detail View

From the detail view you can:

• Select an agent name to view detailed information about the agent

• Select an address to view a map to the listing in Google Maps™

• Call the listing agent by selecting the agent’s phone number

• Email the listing agent by selecting the agent’s email address

Figure 30. Map view

Chapter 4

MLS Data

35

Saved Searches

Saved searches are custom searches that you have saved. Tapping a saved search runs the search and returns your results.

To create a saved search:



3. Select Custom Search.

4. Select the criteria for your search.

Tip: To clear any search criteria you’ve entered, select Clear All at the bottom of the screen.

5. Select Save.

6. Enter a name for the search.

To run a saved search:


2. Select the Listings icon. The list of saved searches you have created is displayed.

Chapter 4

MLS Data

36

Figure 31. List of Saved Profiles

3. Select the saved search.

4. The listings in your market area that match the criteria you selected for the saved search are displayed.

To edit or delete a saved search:


2. Select the Listings icon. The list of saved searches you have created is displayed.

3. Select the arrow to the right of the saved search name.

4. Make any changes to your custom search and click Save or click Delete to delete the saved search.

Delete Listings

The listings can be deleted off of your iPhone:




3. Select Delete Listings.

4. Select Yes to confirm deleting listings.

Chapter 4

MLS Data

Roster

The eKEY software provides a roster of the members in your Association/Board/MLS. The roster data is updated during the first eKEY software update of any given day.

37

View Roster

To view the roster:


2. Select the Roster icon.

3. To search for an agent, enter part or all of the agent’s name.

The eKEY software automatically filters and displays the search results as you enter the criteria.

All agents that have the search criteria you enter in their first name, last name, or office name are displayed.

Figure 32. Roster search and view

4. Roster entries with an email or phone icon next to their name indicate email or phone information is available.

5. To view the detailed contact information, select the agent.

Figure 33. Agent Details

6. To contact the agent, select the phone number or email address shown.

Delete Roster

The roster can be deleted off of your iPhone:




3. Select Delete Roster.

4. Select Yes to confirm deleting the roster.

Chapter 4

MLS Data

38

Chapter 5

Showing Activity

39

Chapter 5 Showing Activity

This chapter explains showing notifications and describes how to view showing activity using the eKEY software.

In this chapter:

Showing Activity .................................................................................... 40

Voice Report ...................................................................................... 40

Showing Notifications and Messages ................................................ 40

Showing Activity on iPhone ............................................................... 42

Disable eKEY Showing Notifications ................................................. 43

Update Listing ID ............................................................................... 43

Chapter 5

Showing Activity

Showing Activity

The eKEY software records the showing information each time you open a key container and sends the information to the Supra network after each showing.

As a listing agent, there are several ways to see who has shown your listings. As a showing agent, you can also get a report of how many properties you’ve accessed.

There are several ways to view showing activity:

• Read a keybox to view it’s showing activity on your iPhone (see

Read Keybox Activity

on page

21)

• Go to the SupraWEB to see the showing activity on your listings or get a report of all the showings you’ve done (see the SupraWEB Guide available at

www.supraekey.com

under

Training Resources for more information on using SupraWEB)

• If you have eKEY Professional service, view showing activity on your iPhone

• Request a report from the KIM voice system (see below)

40

Voice Report

You can request a showing activity report using KIM voice access. You’ll need to have the keybox serial number and shackle code to request the report. You can request a voice or e-mail report. An email report is delivered to your email address on record with your Association or MLS.

To request an activity report from KIM voice:

1. Call KIM voice at 888-968-4032.

2. On your phone keypad, enter your eKEY serial number and PIN code, then press #.

3. Select option 5 from the voice menu.

4. Press 1 for a voice report or 2 for an email report. Follow the instructions to receive the report.

Showing Notifications Messages

Showing notifications automatically display in your eKEY software whenever a keybox in your inventory is shown. Messages sent from Supra, your Association/MLS, or your office broker also are automatically displayed.

Chapter 5

Showing Activity

41

Figure 34. eKEY Notification

Messages and showing notifications can also be viewed later. To view messages:


2. Select Messages.

The number of showings displayed is an accumulation of showings at your listings in the last 14 days.

Figure 35. Messages

Chapter 5

Showing Activity

Showings Activity on iPhone

If you have eKEY Professional service, showing data is delivered to your eKEY software on your iPhone.

To view showing activity on your iPhone:


2. Select the Showings icon. Showing activity for the previous seven days is displayed.


42

Figure 36. Showing information

From the Showing Details screen you can:

• Select the agent name to display the agent’s information from the roster

• Select the agent’s phone number to call the listing agent, or

• Select the keybox to view it in your keybox inventory

To change the number of days activity shown in your eKEY software:

1. On your computer navigate to

www.supraekey.com

.

2. Select Agents-Log on to SupraWEB.

3. Enter your user ID and password and select

Submit. If you haven’t registered for a single sign on (SSO) user ID and password yet, click the How to get access link to register for a login.


5. Select eKEY Showings.

6. Select the number of days of showing activity to be displayed in your eKEY software.

Chapter 5

Showing Activity

Disable eKEY Showing Notifications

You can disable the automatic showing notifications. To disable the automatic showing notification:




3. Turn the eKEY Notifications option off.

4. Select Home to return to the eKEY menu.

43

Figure 37. Disable eKEY Notifications

Update Listing ID

Update the listing ID whenever a keybox is placed on a listing or removed from a listing to keep your keybox showing reports accurate.

To update the listing ID when placing a keybox on a listing, see

Change Keybox Settings

on page 22 for more information. You can also enter the listing ID at SupraWEB by selecting the keybox from the

Assign Listing link and entering the information.

Chapter 6

Support and Troubleshooting

44

Chapter 6 Support and Troubleshooting

This chapter provides information to help you troubleshoot problems and contact technical support in case you need assistance with your eKEY software.

In this chapter:

Support ................................................................................................... 45

Training Library ........................................................................................................... 45

Help Screens .............................................................................................................. 46

Chapter 6


45

Support

If you need assistance troubleshooting your eKEY software, support is available from 5 a.m. to 7 p.m.

Pacific Time, seven days a week.

Website

Email

http://www.supraekey.com

[email protected]

Telephone 877.699.6787

Fax 503.589.8677

To call Support directly from the eKEY software on your iPhone:


2. Select About.

3. Select the phone number shown in the Support Information section to call Support.

Figure 38. Contacting Support

Training Library

Another great resource for assistance with your eKEY software is our training library, available to all agents. To access the library:

1. Go to

www.supraekey.com

2. Scroll down and click the Training Resources link.

Training available here is periodically updated so bookmark this page for future reference.

Chapter 6


Help Screens

Help information is provided in the eKEY software. To access the help information, select the Help icon on the second page of eKEY icon.

46

Figure 39. Help icon

In addition, several screens throughout the eKEY software have an shown in the upper right corner.

Click the for help.

eKEY™ for iPhone User Manual

eKEY

™

for iPhone

User Manual

Contents

Preface

Safety Terms and Symbols

Chapter 1 Introduction

Overview

Requirements

eKEY Software

eKEY Adapter

SupraWEB

KIMvoice

eKEY Setup

Install eKEY Software

Authorize eKEY

Customize PIN

Audio and Vibrate Settings

Chapter 2 Updating

Updating

Manual Update

Disable Automatic Update

Chapter 3 Accessing iBoxes

Accessing iBoxes

Supra eKEY Adapter

Release the Key Container

Place Listing Keys in the iBox

Feedback

Showing Hours

Call Before Showing (CBS)

Cooperating

Release the Shackle

iBox Inventory

View iBox Inventory and Detail Information

Add Keybox to your Inventory

Delete an iBox from your Inventory

Read Activity

View Showing Activity

Change iBox Settings

Chapter 4 MLS Listings and Roster

eKEY Professional

Settings for eKEY Professional

Listings

Market Area

Update Listings

View Listings

Delete Listings

Roster

View Roster

Delete Roster

Chapter 5 Showing Activity

Showing Activity

Voice Report

Showing Notifications Messages

Showings Activity on iPhone

Disable eKEY Showing Notifications

Update Listing ID

Chapter 6 Support and Troubleshooting

Support

Training Library

Help Screens

Related manuals

eKey

Phone

Supra

iBox BT

Supra

iBox

Table of contents