Quoizel BKR1910K Booker 1-Light Black Outdoor Pendant Light Installation Guide
Advertisement
Advertisement
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
.
.
Assembly Instruction Sheet #IS-BKR1910K
For Style BKR1910K
Please go to www.quoizel.com
for product cleaning tips. Go to the Care + Maintenance selection.
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) Medium Base Decorative Filament 60W bulb (provided), Maximum 150W, Alternate bulb (1) 42W CFL Maximum.
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
A
Fixture Loop x 1
Hardware Contents
AA
2015 QuoizelInc.
B
Fixture
Body x 1
Crossbar x 1
BB
Lock Washer x 2
CC
Hex Nut x 2
DD
Nipple x 1
STEP 1
-
Install Fixture Loop and Shade
A. Thread the Fixture Loop (A) onto the
Fixture Body (B). Hand tighten until sung.
B. Place the Shade (C) and the Washer (D) over the Socket and secure with one
Socket Collar (E). Hand tighten until snug. Proceed to thread another Socket
Collar (E) onto the Socket.
Figure 1
C
Shade x 1
D
Wahser x 1
E
Socket Collar x 2
F
Edison
Bulb x 1
EE
Canopy
Chain Loop x 1
FF
Canopy Lock
Ring x 1
GG
Fixture Chain x 1
HH
Quick Link x 2
II
Ceiling
Canopy x 1
A
D
E
E
B
Socket
C
STEP 2
-
Install Crossbar
A.
Attach the Crossbar ( AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included)
.
Tighten until snug
.
Outlet Box
Green Ground
Screw
AA
Outlet Box Screw
(not included)
Figure 2
STEP 3 Install Canopy Chain Loop and Nipple
*
Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at least 0.25” from the end. Pass one Lock Washer (BB) over the end of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place another Lock Washer (BB) over the
Nipple (DD) and then thread the
Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375” above the Crossbar (AA).
C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop (EE).
Place the Ceiling Canopy (II) over the
Canopy Chain Loop (EE) against the ceiling to determine the correct position of the Nipple (DD). Thread the Canopy Lock Ring onto the
Canopy Chain Loop (EE). Adjust the
Nipple (DD) to allow the Ceiling
Canopy (II) to rest against the ceiling when held in place by the Canopy
Lock Ring (FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II). Tighten the Hex Nut (CC) against the
Crossbar (AA) to secure in place.
AA
BB
Figure 3
DD
BB
CC
CC
EE
FF
II
Step
B
Step
A
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing links if needed.
*
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop and the
Canopy Chain Loop (EE), pull the supply wires through the Fixture
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com
November2015
1of2
Chain (GG) alternating links. After the wires are through the Fixture
Chain (GG), pull the Supply Wires and the Ground Wire through the
Canopy Lock Ring (FF) and the
Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain
(GG) to the Fixture Loop with one
Quick Link (HH). Lift the fixture and
Fixture Chain (GG) up and attach the other end of the Fixture Chain
(GG) onto the Canopy Chain Loop
(EE) with another Quick Link (HH).
The fixture will now hang safely.
Close the chain loop at the Ceiling
Canopy Loop (EE).
D. Feed the Supply Wires and Ground
Wire through the Canopy Chain
Loop (EE) and Nipple (DD) into the
Outlet Box. Cut the wires leaving
Approximately 8” of wire extending from the Outlet Box.
E. Refer to Step 5 for wire connections.
F. Raise the Ceiling Canopy (II) and
Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over the
Canopy Chain Loop (EE). Tighten the Canopy Lock Ring (FF) onto the
Canopy Chain Loop (EE) until tight.
Supply
Wires and
Ground Wire
GG
Suggested chain length for Ceiling height :
8’ ceiling : use 2 links of chain and 2 quick links
9’ ceiling : use 11 links of chain and 2 quick links
10’ ceiling : use 20 links of chain and
2 quick links
Figure 4
DD
EE
HH
STEP 6 - Install Bulb
A. This fixture uses Medium
Base Decorative Filament
60W bulb (F), Maximum
150W. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready to use.
Enjoy!
II
Figure 6
FF
HH
BKR1910K
FINISH: MYSTIC BLACK
5”Dia.
A
1
Socket
F
0.75”
119”
OVERALL HEIGHT
INCLUDES 96”
CHAINS AND
(2) QUICK LINKS
STEP 5 - Wire Connections 17.75”
A. Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into outlet box.
10.25”
2
Note: If the electrical wire is going to be cut shorter than provided you will need to identify the "L" line wire and the "N" neutral wire before you cut the excess wire off. One is labeled N and the other labeled L. To do this separate the "L" line wire and the "N" neutral wire as far as you need to. Re-label the wire near where you want to make the cut. Be sure to mark the wire on the side of the fixture and not on the excess wire being cut and removed.
White wire from supply
Black wire from supply (or Red)
Ground wire from supply
2015 QuoizelInc.
6.5”Dia.
8.75”Dia.
10.5”
Ribbed side of wire from fixture identified with the Label “N”
Smooth side of wire from fixture identified with the label “L”
Ground wire from fixture
Figure 5
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4
"
(1)Medium Base
Decorative
Filament 60W bulbs (provided),
Maximum 150W.
1
2
M2233CHK CHAIN
G12233SH SHADE
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com
November2015
1
1
2of2

Public link updated
The public link to your chat has been updated.
Advertisement