Chapter 1
S m a r t V i ew
Medical Station
ZEUS-247/227/197
ZEUS-247/227/197
24”/22”/19” LCD with LED Backlight
®
Intel Core
TM
i7 Quad Core/Dual Core Processor
Intel® QM77 Chipset
Smart View Medical Station
ZEUS-247/ZEUS-227/ZEUS-197 Manual 1st Ed
Jan, 2013
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Copyright Notice
This document is copyrighted, 2012. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, nor for
any infringements upon the rights of third parties, which may result
from its use.
The material in this document is for product information only and
is subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, ONYX Healthcare Inc., assumes no liabilities resulting
from errors or omissions in this document, or from the use of the
information contained herein
ONYX Healthcare Inc. reserves the right to make changes in the
product design without notice to its users
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Acknowledgments

Intel® CoreTM i7 is registered trademarks of Intel® Corporation.

IBM, PC/AT, PS/2 are trademarks of International Business
Machines Corporation.

Microsoft® Windows is a registered trademark of Microsoft®
Corporation.

RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

C&T is a trademark of Chips and Technologies, Inc.

UMC is a trademark of United Microelectronics Corporation.

ITE is a trademark of Integrated Technology Express, Inc.

SiS is a trademark of Silicon Integrated Systems Corp.

VIA is a trademark of VIA Technology, Inc.
All other product names or trademarks are properties of their r
espective owners.
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Packing List
Before you begin installing your Medical Station, please make sure
that the following items have been shipped:

ZEUS-247/227/197 Smart View Medical Station

Utility CD-ROM, which contains Drivers and Utilities
If any of these items are missing or damaged, you should contact
your distributor or sales representative immediately.
Headquarters
Onyx Healthcare Inc.
2F, No.135, Lane 235, Pao-Chiao Rd.,
Hsin-Tien City, Taipei 231, Taiwan, R.O.C.
TEL: +886-2-8919-2188
FAX: +886-2-8919-1699
E-mail: [email protected]
http://www.onyx-healthcare.com
Worldwide Offices:
Onyx Healthcare, USA Inc.
2663 Saturn street, Brea, CA 92821, USA
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Tel : +1-714-996-1800
Fax: +1-714-996-1811
Email: [email protected]
Onyx Healthcare EUROPE B.V.
Ekkersrijt 4002, 5692 DA Son, The Netherlands
Tel : +31-(0)499-462020
Fax: +31-(0)499-462010
Email: [email protected]
Onyx Healthcare Technology GmbH
An der Trift65d
63303 Dreieich , Germany
TEL: +49-(0)61033-7479-00
Fax: +49-(0)61033-7479-49
Email: [email protected]
Onyx Healthcare (SU ZHOU) INC.
Room 12, 2F, Building B, No.5 Xing Han Street, Suzhou Industrial
Park, Jiang Su Province, China
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Tel: +86-512-67625700
Fax: +86-512-67617337
Email: [email protected]
Onyx Healthcare Singapore PTE LTD
57 Genting Lane, #07-00, Singapore 349564
Tel: +65-67498749
Fax +65-67461595
Email: [email protected]
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning.
Do not use liquid or spray detergents for cleaning. Use a damp
cloth.
4. For pluggable equipment, the power outlet must be installed
near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation.
Dropping it or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect
the equipment from overheating. DO NOT COVER THE
OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from
the power source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, only qualified
S m a r t V i ew
Medical Station
ZEUS-247/227/197
service personnel should open the equipment.
S m a r t V i ew
Medical Station
ZEUS-247/227/197
14. If any of the following situations arises, get the equipment
checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d.
The equipment does not work well, or you cannot get it
to work according to the users manual.
e. The equipment has been dropped and damaged.
f.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY
DAMAGE THE EQUIPMENT.
16. External equipment intended for connection to signal
input/output or other connectors, shall comply with
relevant UL / IEC standard (e.g. UL 1950 for IT equipment
and ANSI/AAMI ES 60601-1: 2005 AND CAN/CSA-C22.2 No.
60601-1:08 / IEC 60601 series for systems – shall comply
with the standard IEC 60601-1-1, Safety requirements for
medical electrical systems. Equipment not complying with
UL 60601-1 shall be kept outside the patient environment,
as defined in the standard.
Caution:
It may cause the danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type
recommended by the manufacturer.
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX0
3. Mode of operation: Continuous
4. Type of protection against electric shock: Class I equipment
5. No Applied Part, No AP/APG
S m a r t V i ew
Medical Station
ZEUS-247/227/197
FCC
This device complies with Part 18 FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference
received including interference that may
cause undesired operation.
S m a r t V i ew
Medical Station
ZEUS-247/227/197
UL Module Description
ZEUS-247/227/197 modules are developed to
suitable for the Classification Mark
requirement
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Safety Symbol Description
The following safety symbols are the further explanations for your
reference.
Medical equipment with respect to electric
shock, fire and mechanical hazards only in
accordance with ANSI/AAMI ES 60601-1:
2005 AND CAN/CSA-C22.2 No.
60601-1:08
Attention, consult ACCOMPANYING
DOCUMENTS.
Stand-by (Green light)
Ground wire
Protective Ground wire.
Medical equipment with respect to electric
shock, fire and mechanical hazards only in
accordance with UL 60601-1, and
CAN/CSA C22.2 NO. 601.1
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Contents
Chapter 1 General Information
1.1 Introduction .................................................................... 1-2
1.2 Feature ............................................................................ 1-3
1.3 Specification ................................................................... 1-4
1.4 Dimension ....................................................................... 1-8
Chapter 2 Hardware Installation
2.1 Safety Precautions ......................................................... 2-2
2.2 Quick Tour of the ZEUS-247/227/197 ........................... 2-3
2.3 Turn On and Boot up into Windows…………………….2-7
2.4 Turn off……………………………………………………….2-7
Chapter 3 Driver Installation
Appendix A Miscellanea
A.1 General Cleaning Tips.................................................. C-2
A.2 Cleaning Tools .............................................................. C-3
A.3 Scrap Computer Recycling ........................................ C-5
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Chapter
1
General
Information
S m a r t V i ew
Medical Station
ZEUS-247/227/197
1.1 Introduction
The ZEUS-247/227/197 Smart View Medical Stations are based on
Intel® CoreTM i7 Quad Core/Dual Core processor, which delivers a
performance improvement of more than 100 percent compared to
systems running traditional single-core processors. With two/four
cores, or computing engines, ONYX can simultaneously execute
two/four computing tasks. It accommodates one 2.5” SATA hard
disk drive/SSD and two DDRIII SODIMM up to 16GB.
The high brightness LCD, Low Noise solution, integrated
multimedia functions and extensive expansion options make them
the perfect platform upon which to build comprehensive lifestyle
computing applications.
The ZEUS-247/227/197 include all the features of a powerful
computer into a slim and attractive chassis. The ZEUS-247 has a
24” 300 nits TFT display with 1920 x 1200 resolutions. ZEUS-227
has a 22” 300 nits TFT display with 1920 x 1080 resolutions.
ZEUS-197 has a 19” 300 nits TFT display with 1280 x 1024
resolutions. Integrating with high brightness LCD is easier to
analyze DICOM image. ZEUS series owns side mount USB 3.0
ports, slim DVD-RW drive and a smart card reader to support high
speed data transfer and ID check by smart card reader. Combining
the ZEUS-247/227/197 into your system can achieve both
cost-saving and efficient improvements in common applications
including
Surgical,
Radiology,
PACS
Chapter 1 General Information 1-1
(Picture
Archiving
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Communication Systems), LIS (Lab Information Systems) and
Electronic Medical Record. The ZEUS-247/227/197 are definitely
your perfect choices.
Chapter 1 General Information 1-2
S m a r t V i ew
Medical Station
ZEUS-247/227/197
1.2 Feature

24”/22”/19” Intel® CoreTM i7 Quad Core/Dual Core Processor

Supports Dual Channel DDR3 SODIMM up to 16GB

Built-in RFID and Smart Card Security (Optional)

Supports PCI Express[x16] Expansion

High Speed USB 3.0 Ports

10 Smart Function Keys

DICOM Compliance(optional)
Chapter 1 General Information 1-3
S m a r t V i ew
Medical Station
ZEUS-247/227/197
1.3 Specification
Hardware Specifications
Display
ZEUS-247: 24” 1920x1200 LCD
ZEUS-227: 22” 1920x1080 LCD
ZEUS-197 19” 1280x1024 LCD
CPU
Intel® CoreTM i7/i3 Processor
Disk Drive
2.5” Hard Disk Drive/Solid State Drive
Space
Slim DVD-RW Drive (optional)
Expansion
One PCI Express[x16] expansion
Function
Key
Power On/Off, Speaker Volume Up/Down, LCD Brightness
Up/Down, LCD On/Off, Touch Screen On/Off, Display
Mode(optional), Reading Light On/Off
I/O
1x Isolated RS-232 port
1x Isolated USB 2.0 port
4x USB 2.0 ports
4x USB 3.0 ports
2x Isolated Gigabit LAN
1x Display Port
Sound:
1 x Line-out
1 x Mic-in
LCD Specifications
Model Name
ONYX-247 series
ONYX-227 series
Display Type
24” LCD
22” LCD
Max. Resolution
1920 x 1200
1920 x 1080
Max. Colors
16.7M
16.7M
Chapter 1 General Information 1-4
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Dot Size (mm)
0.297 x 0.297
0.294 x 0.294
Luminance (cd/m2)
300(TYP)
300 or 250 (TYP)
Back Light Life Time 30,000 Hrs
Model Name
ONYX-197 series
Display Type
19” LCD
Max. Resolution
1280 x 1024
Max. Colors
16.7M
Dot Size (mm)
0.297 x 0.297
Luminance (cd/m2)
300 or 350(TYP)
50,000 or 30,000 Hrs
Back Light Life Time 50,000 Hrs
Note:
All ONYX LCD products are manufactured with High precision technology.
However, there are a small number of defective pixels in all LCD panels
that are not able to change color. This is a normal occurrence for all LCD
displays from all manufacturers and should not be noticeable or
objectionable under normal operation. All LCD panels are qualified for
industry standard conditions in the following: total 7 dead pixels on a
screen or if there are 3 within 1 inch square area of each other on the
display.
Chapter 1 General Information 1-5
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Mechanical Specifications
Architecture
Close-frame
Front Bezel
Plastic bezel with resistive touch screen
Color
White
Mounting / Holder
VESA 75/100mm
Construction
3mm ABS + PC TYPE Plastic housing
Dimension (WxHxD) ZEUS-247: 600mmx 415mm x 65 mm
ZEUS-227: 546mm x 351mm x 66mm
ZEUS-197: 450mm x 388mm x 66mm
Net Weight
ZEUS-247: 21.4 lb (9.7 Kg)
ZEUS-227: 18.7 lb (8.5 kg)
ZEUS-197: 16.5lb (7.5Kg)
Power Supply Specifications
Model
POWER-WIN PW-M110A-1Y240G
Input Voltage
90~264 V AC, 2A max. @ 47 ~ 63 Hz
Output Voltage
MTBF
24V, 4.6A, 110W max.
100,000 hrs operation at 25˚C
Chapter 1 General Information 1-6
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Environmental Specifications
Operating Temperature
0˚C to 40˚C (32˚F ~104˚F)
Storage Temperature
-20˚C to 60˚C (-4˚F ~140˚F)
Storage Humidity
5% to 95%@ 40˚C, non-condensing
Vibration
0.5G / 5 ~ 500Hz (Random) / operation
Shock
15G peak acceleration (11 msec. duration) /
operation
Drop
76cm (1 Corner, 3 Edge, 6 Surface)
EMI / Safety
CE / FCC Class B/UL 60601-1/EN 60601-1
IP
Front bezel, IP-65 Certified
Noise
35db (full operation)
Touch Screen (Optional)
Type
Projective Capacitive / 5-wire Resistive
Interface
USB interface
Light Transmission
> 75%
Life Time
35 million activations
Chapter 1 General Information 1-7
S m a r t V i ew
Medical Station
ZEUS-247/227/197
1.4 Dimension
ZEUS-247
Chapter 1 General Information 1-8
S m a r t V i ew
Medical Station
ZEUS-247/227/197
ZEUS-227
Chapter 1 General Information 1-9
S m a r t V i ew
Medical Station
ZEUS-247/227/197
ZEUS-197
Chapter 1 General Information 1-10
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Chapter
2
Hardware
Installation
Chapter 2 Hardware Installation 2-1
S m a r t V i ew
Medical Station
ZEUS-247/227/197
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis
Chapter 2 Hardware Installation 2-2
S m a r t V i ew
Medical Station
ZEUS-247/227/197
2.2 Quick Tour of the ZEUS-247/227/197
Before you start to set up the ZEUS-247/227/197, take a moment to
become familiar with the locations and purposes of the controls,
drives, connections and ports, which are illustrated in the figures
below.
When you place the ZEUS-247/227/197 upright on the desktop, its
front panel appears as shown in Picture 2-1.
Picture 2.1: Front View of the Zeus Series
Chapter 2 Hardware Installation 2-3
S m a r t V i ew
Medical Station
ZEUS-247/227/197
When you turn the Medical Station around and look at its rear cover,
the sunken I/O section is at the bottom of the station, as shown in
Picture 2-2. (The I/O section includes various I/O ports, including a
serial port, Display Port, the Ethernet ports, USB ports, the
microphone jack, PCI Express slot, and so on.) The Medical Station
integrates WLAN function by using Mini Card.
ZEUS-247
ZEUS-227
Chapter 2 Hardware Installation 2-4
S m a r t V i ew
Medical Station
ZEUS-247/227/197
ZEUS-197
Picture 2.2: Rear view of the Zeus Series
When you turn the Medical Station around and look at its left side,
two USB 3.0 ports, the smart card reader and DVD-RW drive are on
Chapter 2 Hardware Installation 2-5
S m a r t V i ew
Medical Station
ZEUS-247/227/197
the right side and the left side of the Medical Station as shown in
Picture 2-3.
Picture 2.3: Left view of the Zeus Series
Chapter 2 Hardware Installation 2-6
S m a r t V i ew
Medical Station
ZEUS-247H/227S/197S
2.3 Turn On and Boot up into Windows OS
This section is for Windows operating system only. If you are
installing a different operating system, please contact your vendor
for installation details.
Your ZEUS will begin loading Windows OS once you push the
power button to turn power on. After less than one minute, Windows
desktop screen will appear.
You can select the programs from the start menu in the left-down
corner of the desktop screen.
2.4 Turn off
Turning off ZEUS properly is important for system reliability. There
are two ways to turn off the system.
1. On the start menu, click “shut down” and select “OK”
2. Push the power button and then the system will shut down
automatically
Chapter3 Award BIOS Setup 3-2
S m a r t V i ew
Medical Station
ZEUS-247/227/197
Chapter
3
Driver
Installation
Chapter3 Driver Installation 3-1
S m a r t V i ew
Medical Station
ZEUS-247/227/197
There are several installation ways depending on the driver
package under different Operating Systems.
Please follow the sequence below to install the drivers:
Step 1 – Install INF Driver
Step 2 – Install VGA Driver
Step 3 – Install LAN Driver
Step 4 – Install Audio Driver
Step 5 – USB 3.0 Driver
Step 6 – RAID&AHCI Driver
Step 7 – ME Driver
Step 8 – TPM Driver
Step 9 – Serial Port Driver(optional)
Step 10 – Smart Card Driver
Step 11 – Touch Panel Driver
Chapter 4 Drivers Installation 3-2
S m a r t V i ew
Medical Station
ZEUS-247H/227S/197S
Appendix
A
Miscellanea
Appendix A Miscellanea A-1
S m a r t V i ew
Medical Station
ZEUS-247H/227S/197S
A.1 General Cleaning Tips
You may need the following precautions before you begin to clean
the computer. When you clean any single part or component for the
computer, please read and understand the details below fully.
1. Never spray or squirt the liquids directly onto any computer
component. If you need to clean the device, please rub it
with a piece of dry cloth.
2. Be cautious of the tiny removable components when you
use a vacuum cleaner to absorb the dirt on the floor.
3. Turn the system off before you start to clean up the
component or computer.
4. Never drop the components inside the computer or get
circuit board damp or wet.
5. Be cautious of all kinds of cleaning solvents or chemicals
when you use it for the sake of cleaning. Some individuals
may be allergic to the ingredients.
6. Try not to put any food, drink or cigarette around the
computer.
7. ONYX Healthcare Inc. has tested and verified these
cleaning disinfectants, CIDEX, Viraguard, Control III
Disinfectant Germicide, Caviwipes, Dispatch Disinfectant
Cleaner CLH69101, Puregreen 24 Disinfectant, can be
used with the ONYX-175/195. Use of any other
Appendix A Miscellanea A-2
S m a r t V i ew
Medical Station
ZEUS-247H/227S/197S
disinfectants will void the warranty.
A.2 Cleaning tools
Although many companies have created products to help improve
the process of cleaning your computer and peripherals users can
also use household items to clean their computers and peripherals.
Below is a listing of items you may need or want to use while
cleaning your computer or computer peripherals.
Keep in mind that some components in your computer may only be
able to be cleaned using a product designed for cleaning that
component, if this is the case it will be mentioned in the cleaning
tips.

Cloth - A piece of cloth is the best tool to use when rubbing
up a component. Although paper towels or tissues can be
used on most hardware as well, we still recommend you to
rub it with a piece of cloth.

Water or rubbing alcohol – You may moisten a piece of
cloth a bit with some water or rubbing alcohol and rub it on
the computer. Unknown solvents may be harmful to the
plastics parts.

Vacuum cleaner - Absorb the dust, dirt, hair, cigarette
particles, and other particles out of a computer can be one
of the best methods of cleaning a computer. Over time
these items can restrict the airflow in a computer and cause
Appendix A Miscellanea A-3
S m a r t V i ew
Medical Station
ZEUS-247H/227S/197S
circuitry to corrode.

Cotton swabs - Cotton swaps moistened with rubbing
alcohol or water are excellent tools for wiping hard to reach
areas in your keyboard, mouse, and other locations.

Foam swabs - Whenever possible it is better to use lint
free swabs such as foam swabs.
Note:
We strongly recommended that you should shut down the
system before you start to clean any single components.
Please follow the steps below.
1.
Close all application programs.
2.
Close operating software.
3.
Turn off power switch
4.
Remove all device
5.
Pull out power cable
Appendix A Miscellanea A-4
S m a r t V i ew
Medical Station
ZEUS-247H/227S/197S
A.3 Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform us as
soon as possible for the suitable solution. For the computers that
are no longer useful or work well, please contact with worldwide
distributors for recycling.
The worldwide distributors show on the following website:
http://www.onyx-healthcare.com.tw/Contact.php
Note:
Follow the national requirement to dispose unit
Appendix A Miscellanea A-5
MI/O Extension Modules
MIOe-210
MIOe-220
4 x RS232/422/485,
2 x RS422/485, 8-bit GPIO
3 x Intel Gigabit Ethernet
®
Specifications
Specifications
General
Bus Interface
MIOe LPC
Ports
4 x RS232/422/485, 2 x RS422/485
GPIO
8-bit with 3.3V level
Communications
Data Bits
5, 6, 7, 8
RS-422: TxD+, TxD-, RxD+, RxDRS-485: DATA+, DATAData Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR,
DCD, RI, GND
IRQ
Depends on MI/O CPU Board
Parity
even, odd, sticky or no
Speed
50 to 115.2k Baud
Stop Bits
1, 1.5, 2
Protection
EFT Protection
Air gap ±15kV, contact ±8kV
Compatibility
Rear I/O
MI/O-Compact
Mechanical
MI/O-Compact
Function
MI/O-Compact*, MI/O-Ultra*
Environment
Dimensions
146 x 102 mm (5.7" x 4")
Weight
0.186 kg (0.41 lb)
Operating
0 ~ 90 % relative humidity,
Humidity
non-condensing
Operating
0 ~ 60° C (32 ~ 140° F)
Temperature
Storage
-40° C ~ 85° C and 60° C @ 95% RH
Temperature
Non-Condensing
Power
Power Supply
Supported by MI/O Extension SBC
Voltage
General
Bus Interface
MIOe PCI Express
Chipset
Intel® 82583V Gigabit Ethernet Controller
PCIe Switch
PLX PEX8605
Port
3 x RJ45
Speed
10/100/1000 Mbps
Compatibility
Rear I/O
MI/O-Compact
Mechanical
MI/O-Compact
Function
MI/O-Compact, MI/O-Ultra
Mechanical and Environmental
Dimensions
102 x 83 mm (4" x 3.2")
(L x W)
Weight
0.182 kg (0.401 lb)
Operating
Standard operating: 0 ~ 60° C
Temperature
(32 ~ 140° F)
Operating
0% ~ 90% relative humidity,
Humidity
non-condensing
Storage
-40° C ~ 85° C and 60° C @ 95% RH
Temperature
Non-Condensing
Power
Power Supply
Supported by MI/O Extension SBC
Voltage
Ordering Information
P/N
MIOe-220-L3A1E
MIOe-220-B3A1E
Description
3 x Intel® Gigabit Ethernet without
PCIe Switch
3 x Intel® Gigabit Ethernet with PCIe
Switch (for MIO-5250 /MIO-5251/
MIO-5271)
MIOe-230
48-bit LVDS or DisplayPort1,
2 x USB 2.0
Specifications
General
Bus Interface
MIOe Displayport & USB 2.0
Controller
Chrontel CH7511
Brightness
Supported
Control
USB
2 x USB 2.0
Compatibility
Rear I/O
MI/O-Ultra
Mechanical
MI/O-Compact, MI/O-Ultra
Function
MI/O-Compact2, MI/O-Ultra2
Mechanical and Environmental
Dimensions
100 x 72 mm (3.9" x 2.8")
(L x W)
Weight
0.084 kg (0.185 lb)
Operating
0 ~ 60° C (32 ~ 140° F)
Temperature
Operating
0% ~ 90% relative humidity,
Humidity
non-condensing
Power
Power Supply
Supported by MI/O Extension SBC
Voltage
Support by request
Requires customized BIOS or HW adjustment for MI/O CPU
board support.
1
2
Ordering Information
P/N
MIOe-230-L0A1E
Description
48-bit LVDS or DisplayPort, 2 x USB 2.0
* Requires customized BIOS for MI/O CPU board support.
Ordering Information
P/N
MIOe-210-D6A1E
Description
4 x RS232/422/485, 2 x RS422/485,
8-bit GPIO
Accessories
Part No.
1703040157
Description
RS-422/485 W/D-SUB COM
4P 15 cm
Quantity
2
MI/O Extension SBCs, Modules and Chassis
All product specifications are subject to change without notice
Last updated : 26-Mar-2014
MI/O Extension Modules
MIOe-110
2 x RS-232, 2 x RS-232/422/485
(with power and isolation),
2 x USB 2.0
MIOe-120
2 x GbE, HDMI, Mini PCIe, SIM
holder, speaker out, LPC,
2 x USB 2.0
MIOe-PWR1
12-24V DC to DC Power Module
MI/O-Chassis compliant
UL
®
Specifications
Specifications
General
Bus Interface
Super I/O
Rear I/O
MIOe LPC/USB
SCH3106
COM port
COM1/2: Both at coastline and internal box
wafer, simultaneously
COM1: RS-232/422/485 (With isolation.
RS-485 with auto flow control).
COM2: RS-232/422/485 (Supports wake
on ring. Supply 5V/12V power selected by
jumper. RS-485 with auto flow control).
General
Internal I/O
COM port
COM3/4: RS-232 (Support wake on ring)
USB 2.0
2
Communications
Data Bits
5, 6, 7, 8
RS-422: TxD+, TxD-, RxD+, RxDRS-485: DATA+, DATAData Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR,
DCD, RI, GND
IRQ
Depends on MI/O CPU Board
Parity
even, odd, sticky or no
Speed
50 to 115.2k Baud
Stop Bits
1, 1.5, 2
Protection
Air gap ±15kV and contact ±8kV for all
ESD
COM ports
Isolation
2.5kV for COM1
Compatibility
Rear I/O
MI/O-Ultra
Mechanical
MI/O-Ultra
Function
MI/O-Compact*, MI/O-Ultra*
Environment
Dimensions
100 x 72 mm (3.9" x 2.8")
Weight
0.04 kg (0.09lb), only for board
Operational
0 ~ 60° C (32 ~ 140° F)
Temperature
Operational
40° C @ 95% RH Non-Condensing
Humidity
Storage
-40° C ~ 85° C and 60° C @ 95% RH
Environment
Non-Condensing
Power
Power Supply
Supported by MI/O Extension SBC
Voltage
* Requires customized BIOS for MI/O CPU board support
Ordering Information
P/N
MIOe-110F-00A1E
MIOe-110L-00A1E
Description
2 x RS-232/422/485, 2 x RS-232,
w/ isolation, 2 x USB
1 x RS-232/422/485, 2 x RS-232,
w/o isolation, 2 x USB
Description
COM3/4 cable 22cm
General
Input Voltage
Output Voltage
Output Current
Protection
12 to 24 VDC ±5%
12V ±10%
Max. 5A
OVP, OCP, Anti-reverse
Input: Phoenix 2pin
Connector type
Output: ATX 2x2pin
Mechanical and Environmental
Dimensions (L x W)
90 x 53 mm (3.5" x 2.1")
Operating Temperature 0 ~ 60° C (32 ~ 140° F)
Weight
0.084 kg (0.185 lb)
0% ~ 90% relative humidity,
Operating Humidity
non-condensing
Ordering Information
P/N
MIOe-PWR1-00A1E
MIOe-PWR1Z-00A1E
Part No.
1700021072-01
HDMI: Only for MIO-2261, supported by request
LPC: Supported by OEM BIOS for PCA-COM232-00A1E,
PCA-COM485-00A1E, and PCA-TPM-00A1E
MIO-5250 doesn’t support MIOe-120L
Ordering Information
MIOe-120F-00A1E
MIOe-120L-00A1E
Description
COM1/2 internal cable 30cm
2 ports USB cable w/o bracket, 12cm
P/N
1700019001
1700019071
PCA-COM232-00A1E
PCA-COM485-00A1E
PCA-TPM-00A1E
Description
12-24V DC to DC power module
12-24V DC power module
-20 ~80 ° C
Accessories
Description
2 x GbE w/ PCIe switch, 2 x USB, Mini
PCIe, SIM holder, speaker-out with
amplifier, LPC
1 x GbE w/o PCIe switch, 2 x USB, Mini
PCIe, SIM holder, speaker-out with
amplifier, LPC
Optional Accessories
Quantity
1
Optional Accessories
P/N
1700019414
1700019071
* 1.
2.
3.
P/N
Accessories
P/N
1700018999
MIOe PCI Express/ USB/ LPC/ Audio
line-out
Ethernet controller GbE Intel® 82583V
PCIe Switch
PLX PEX8605
USB Hub Controller Terminus FE1.1 USB 2.0 4-port hub
Rear I/O
1 (10/100/1000 Mbps), both at coastline
GbE
and internal box wafer, simultaneously
2 (Both at coastline and internal box wafer,
USB 2.0
simultaneously)
HDMI
1 (by request, only for MIO-2261)
Internal I/O
GbE
1 (10/100/1000 Mbps)
1 with amplifier (Max 2.2W/ch stereo into
Speaker out
a 3Ω load )
1 (support extra four COM ports by PCALPC
COM232-00A1E or PCA-COM485-00A1E,
TPM module by PCA-TPM-00A1E)
Expansion
1 (full size, with SIM holder, including of
Mini PCIe
USB interface)
Compatibility
Rear I/O
MI/O-Ultra
Mechanical
MI/O-Compact, MI/O-Ultra
Function
MI/O-Compact*, MI/O-Ultra*
Mechanical and Environmental
Dimensions (L x W) 100 x 72 mm (3.9" x 2.8")
Weight
0.04 kg (0.09lb), only for board
Operational
Standard operating: 0 ~ 60° C (32 ~ 140° F)
Temperature
Operational
40° C @ 95% RH Non-Condensing
Humidity
Storage
-40° C ~ 85° C and 60° C @ 95% RH
Temperature
Non-Condensing
Power
Power Supply
Supported by MI/O Extension SBC
Voltage
Bus Interface
Specifications
Description
1 x LAN cable, 15cm
2 ports USB cable w/o bracket, 12cm
4 x RS-232 extension module,
31.5x48mm
4 x RS-422/485 extension module,
31.5x48mm
TPM module, 31.5 x 48 mm
Online Download www.advantech.com/products
Description
Power cable 2*2P-4.2/2*2P-4.2, 10cm
User Manual
POC-W211
Point-of-Care Terminal with
Intel® Core™ i7 or i3 Processor
and a 21.5" TFT LCD
Instructions for the User
The document combines text and illustrations, providing a comprehensive overview
of the system. The information is presented as a sequential series of actions, allowing the user to learn directly how to use the device.
The text provides explanations and instructs the user step-by-step in the practical
use of the product, with short, clear instructions in an easy-to-follow sequence.
Definitions
Warning! A WARNING statement provides important information about a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution! A CAUTION statement provides important information about a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury to the user or patient or in damage to the equipment or
other property.
Note!
A NOTE provides additional information intended to avoid inconveniences during operation.
Safety Instructions
1.
2.
3.
Strictly follow these Instructions for Use; please read these safety instructions
carefully.
Please keep this User Manual for later reference; any use of the product
requires full understanding and strict observation of all portions of these instructions. Observe all WARNINGS and CAUTIONS as rendered throughout this
manual and on labels on the equipment.
Repair of the device may only be carried out by trained service personnel.
Advantech recommends that a service contract be obtained with Advantech
Service and that all repairs also be carried out by them. Otherwise the correct
functioning of the device may be compromised.
Warning! Because of the danger of electric shock, never remove the cover of a
device while it is in operation or connected to a power outlet.
POC-W211 User Manual
Part No. 2008W22100
Edition 1
Printed in Taiwan
February 2012
ii
4.
5.
If one of the following situations arises, have the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning and keep this equipment away from humidity.
Caution! To avoid short-circuiting and otherwise damaging the device, do not
allow fluids to come in contact with the device. If fluids are accidentally
spilled on the equipment, remove the affected unit from service as soon
as possible and contact the service personnel to verify that patient
safety is not compromised.
6.
Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage. For plug-in equipment, the power outlet socket must
be located near the equipment and must be easily accessible.
Caution! To prevent overheating, do not cover the openings or place the device in
direct sunlight or near radiant heaters.
7.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet. Position the power cord so that people cannot
step on it. Do not place anything over the power cord. If the equipment is not
used for a long time, disconnect it from the power source to avoid damage by
transient over voltage.
Caution! Do not leave this equipment in an uncontrolled environment where the
storage temperature is below -20° C (-4° F) or above 60° C (140° F).
This may damage the equipment.
8.
If your computer does not keep the correct time or the BIOS configuration has
been reset to default, the battery may have no charge.
Caution! Do not replace battery yourself. Please contact a qualified technician or
your retailer.
The computer is provided with a battery-powered, real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
Caution! The battery charging indicator is not included with this device. It will be
added to the finished system assembly and be shown with the completed system.
iii
POC-W211 User Manual
9.
Improper installation of VESA mounting can result in serious personal injury!
VESA mount installation should be operated by professional technician, please
contact the service technician or your retailer if you need this service. The detail
operating procedure is specified in Appendix A.
10. Classification:
1). Supply Class I adapter
2). No applied part
3). IPX1
4). Continuous Operation
5). Not AP or APG category
Warning! This device is not suitable for use in the presence of flammable anesthetic mixture with air, oxygen, nitrous oxide, or for life support systems.
11. Environmental protection: follow national requirements to dispose of unit.
12. Maintenance: to properly maintain and clean the surfaces, use only the
approved products or clean with a dry applicator.
Caution! When servicing the device, always use replacement parts that are qualified to Advantech standards. Advantech Digital Healthcare cannot warrant or endorse the safe performance of third-party replacement parts
for use with our medical device.
13. Make sure the user does not allow contact between SIP/SOPs and the patient
at the same time.
14. When networking with electrical devices, the operator is responsible for ensuring that the resulting system meets the requirements set forth by the following
standards:
– EN 60601-1 (IEC 60601-1)
Medical electrical equipment
Part 1: General requirements for safety
– EN 60601-1-1 (IEC 60601-1-1)
Medical electrical equipment
Part 1-1: General requirements for safety
Collateral standard: Safety requirements for Medical electrical systems
– EN 60601-1-2 (IEC 60601-1-2)
Medical electrical equipment
Part 1-2: General requirements for safety
Collateral standard: Electromagnetic compatibility; Requirements and tests
15. Accessory equipment connected to analog and digital interfaces must be in
compliance with the respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)
POC-W211 User Manual
iv
Furthermore all configurations shall comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part
or signal output part is configuring a medical system, and is therefore, responsible that the system complies with the requirements of the system standard IEC
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC 60XXX certified equipment outside of the patient environment. If in doubt, consult the technical services
department or your local representative.
Caution! Use suitable mounting apparatus to avoid risk of injury.
16. Grounding reliability can only be achieved when the equipment is connected to
an equivalent receptacle marked "Hospital Only" or "Hospital Grade".
17. Use a power cord that matches the voltage of the power outlet, which has been
approved and complies with the safety standard of your particular country.
Note!
Environmental protection
Follow national requirements to dispose of unit.
Explanation of Graphical Symbols
IEC 60878 and ISO 3864-B.3.6 : Warning: dangerous voltage
ISO 7000-0434 : Caution, consult ACCOMPANYING DOCUMENTS.
ISO 7000-1641 : Follow operating instructions or consult instructions for
use.
IEC 60417 -5009 : STAND-BY.
IEC 60417-5031 : Direct current.
IEC 60417-5021 : Equipotentiality.
v
POC-W211 User Manual
Disposing of Old Products
Within the European Union
EU-wide legislation, as implemented in each member state,
requires that waste electrical and electronic products carrying the
mark shown at left must be disposed of separately from normal
household waste. This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your display products, please follow the guidance of your
local authority, or ask the shop where you purchased the product,
or if applicable, follow any agreements made between you and the
provider.
The mark on electrical and electronic products only applies to the
current European Union Member States.
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment
generates, uses and can radiate radio frequency energy. If not installed and used in
accordance with this user manual, it may cause harmful interference to radio communications.
Note that even when this equipment is installed and used in accordance with this
user manual, there is still no guarantee that interference will not occur. If this equipment is believed to be causing harmful interference to radio or television reception,
this can be determined by turning the equipment on and off. If interference is occurring, the user is encouraged to try to correct the interference by one or more of the
following measures:
 Reorient or relocate the receiving antenna
 Increase the separation between the equipment and the receiver
 Connect the equipment to a power outlet on a circuit different from that to which
the receiver is connected
 Consult the dealer or an experienced radio/TV technician for help
Warning! Any changes or modifications made to the equipment which are not
expressly approved by the relevant standard’s authority could void your
authority to operate the equipment.
POC-W211 User Manual
vi
List of Accessories
Before installing your Point-of-Care Terminal, ensure that the following materials
have been received:
 POC-W211 series Point-of-Care Terminal
 Accessories for POC-W211
 CD-ROM disc-"Drivers, User's manual and Utilities"
 Mounting kits and packet of screws.
 VESA mounting note x1
 China RoHs note x1
Warning! No user serviceable parts inside; refer servicing to qualified personnel.
Only the accessories indicated on the list of accessories above have
been tested and approved to be used with the device. Accordingly it is
strongly recommended that only these accessories be used in conjunction with the specific device. Otherwise the correct functioning of the
device may be compromised.
Additional Information and Assistance
Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following
information ready before you call:
 Product name and serial number
 Description of your peripheral attachments
 Description of your software (operating system, version, application software,
etc.)
 A complete description of the problem
 The exact wording of any error messages
 This equipment is a source of electromagnetic waves. Before use please, make
sure that there are not EMI sensitive devices in its surrounding which may malfunction therefore.
Environmental protection

Follow national requirements to dispose of unit.
Manufacturer:
Advantech Co., Ltd.
No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei,
Taiwan 114, R.O.C.
TEL: (02) 2792-7818
Distributed in Europe by:
Advantech Europe GmbH Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel: 49-211-97477350
Fax: 49-211-97477300
Visit the Advantech websites at www.advantech.com or www.advantech.com.tw if
you need more information.
vii
POC-W211 User Manual
POC-W211 User Manual
viii
Contents
Chapter
Chapter
1
General Information ............................1
1.1
1.2
1.3
1.4
Introduction ............................................................................................... 2
Specifications ............................................................................................ 2
Dimensions ............................................................................................... 4
Figure 1.1 Dimensions of the POC-W211 ................................... 4
Figure 1.2 VESA Mounting of the POC-W211............................. 4
Figure 1.3 POC-W211 Front Panel.............................................. 5
Figure 1.4 POC-W211 Back I/O .................................................. 5
1.3.1 Optional Modules .......................................................................... 5
Point-of-Care Terminal Cleaning and Disinfecting .................................... 6
2
System Setup .......................................7
2.1
A Quick Tour of the POC-W211................................................................ 8
2.1.1 Front View..................................................................................... 8
Figure 2.1 Front View of the Point-of-Care Terminal ................... 8
2.1.2 Bottom View.................................................................................. 9
Figure 2.2 Bottom View ............................................................... 9
2.1.3 Rear View ..................................................................................... 9
Figure 2.3 Rear view of the Point-of-Care Terminal .................... 9
Figure 2.4 Rear view of Multi I/O ports ...................................... 10
2.1.4 Left-side View ............................................................................. 10
Figure 2.5 Left side View ........................................................... 10
2.1.5 Right-side View ........................................................................... 11
Figure 2.6 Right-side View......................................................... 11
Installation Procedures............................................................................ 11
2.2.1 Connecting the Power Cord........................................................ 11
Figure 2.7 Connecting the Power Cord ..................................... 12
2.2.2 Connecting the Ground Pin......................................................... 12
Figure 2.8 POC-W211 Equipotential Terminal Pin .................... 12
Figure 2.9 Grounding cable with connector ............................... 12
Running the BIOS Setup Program .......................................................... 13
Installing System Software...................................................................... 13
Installing the Drivers................................................................................ 13
Table 2.1: The file directory on "Drivers and Utilities" CD-ROM 14
2.2
2.3
2.4
2.5
Chapter
Chapter
Chapter
3
Driver Installation ..............................21
3.1
3.2
Introduction ............................................................................................. 22
Automatic Driver Installation ................................................................... 22
4
Utilities and Hot Fixes .......................23
4.1
4.2
Introduction ............................................................................................. 24
Wakeup by External USB Device at S3 Resume (Wakeup) ................... 24
4.2.1 Installation for Windows XP ........................................................ 24
5
Operation and Safety Information....25
5.1
5.2
General Safety Guide.............................................................................. 26
Protecting Your Optical Drive.................................................................. 26
ix
POC-W211 User Manual
Chapter
5.3
5.4
Thermal................................................................................................... 26
Disconnect the Power ............................................................................. 26
6
PCM-8709 Connector Map and Table..
29
6.1
6.2
Motherboard Top Side ............................................................................ 30
Motherboard Bottom Side ....................................................................... 30
Table 6.1: MB Connector Table ................................................ 31
I/O Board................................................................................................. 31
Table 6.2: I/O Connector Table ................................................. 32
6.3
Chapter
7
PCM-8709 Jumper Settings.............. 33
7.1
Motherboard............................................................................................ 34
Figure 7.1 PCM-8709 Motherboard Top Side ........................... 34
I/O Board................................................................................................. 34
Figure 7.2 PCM-8709 I/O Top Side ........................................... 34
Table 7.1: Jumper Settings: ...................................................... 35
Table 7.2: CN: Clear CMOS...................................................... 35
Table 7.3: CN2: Clear ME ......................................................... 35
Table 7.4: CN3: VBIOS Setup................................................... 36
Table 7.5: CN3: Select Boot Main Display Setup...................... 36
Table 7.6: CN4: ME Manufacturing Mode ................................. 36
Table 7.7: CN8: System Reset.................................................. 37
Table 7.8: CN12 (MB): LVDS Voltage Select............................ 37
Table 7.9: CN12 (IO): COM1 RS-232/422/485 Output Type Settings.......................................................................... 37
7.2
Chapter
8
Front Bezel Button............................ 39
8.1
Introduction ............................................................................................. 40
8.1.1 Front Button Map ........................................................................ 40
9
POC-W211 Advanced BIOS Function .
41
9.1
Introduction ............................................................................................. 42
Appendix A
POC-W211 VESA Mounting.............. 45
A.1
Install VESA Mounting ............................................................................ 46
Figure A.1 VESA Mounting 75x75mm, 100x100 mm ................ 46
Chapter
POC-W211 User Manual
x
Chapter
1
1
General Information
1.1 Introduction
The POC-W211 is a multimedia Intel® Core™ i7 or i3 processor series designed for
mobile computing as a Point-of-Care terminal (POC.) It is a PC-based system with
21.5" wide screen TFT LCD display, single VGA Port, HDMI out, dual on-board 10/
100/1000 PCI-E Ethernet controllers, and one LAN port. It supports the Intel AMT7.0
function, has dual COM ports, quad USB 2.0 ports and a 24-bit stereo audio controller. With an optional 2.5" SATA drive, the POC-W211 is a user-friendly computer. For
system integrators, this highly integrated multimedia system lets you easily build a
Point-of-Care Terminal into your applications. The POC-W211 makes it an ideal and
safe point-of-care solution for patients and hospital practitioners.
The POC-W211 is specially designed to resist spills and water damage, and ensures
dust resistance with its protected LCD and sealed ports. The POC-W211 is a reliable
solution to your application's processing requirements.
Intended use - The POC-W211 is intended to serve as a Point-of-Care terminal
(POC) for integration with hospital systems. POC-W211 is designed for general purpose medical computing in the hospital environment, for data collection and for displaying information.
It should not be used as a life-support system.
The latest version of this user manual is available for download from
http://support.advantech.com.tw/support/
1.2 Specifications
Chipset
QM67
CPU
Intel® Core™ i7-2655LE Processor (4M
Cache,2.2GHz)
Intel® Core™ i3-2340UE Processor (3 M Cache,
1.3 GHz)
Computing System Front Side Bus
Display
Expansion Slot
Storage
POC-W211 User Manual
Internal CPU
Memory
Up to 16 GB DDR3 1333 MHz SDRAM
Graphics Controller
Integrated Intel® HD Graphics
Operating System
XP, WIN7
Input Ratings
18Vdc, 5.5A
Display Size
21.5” wide TFT color LCD (16:9)
Max. Resolution
1920(H) x 1080(V)
Max. Colors
16.7M colors (RGB 8bits)
Pixel Pitch (mm)
248.25x248.25
Viewing Angle
178º/178 º
Luminance
250 cd/m2
Backlight
LED
LCD MTBF
30,000 Hours
Contrast Ratio
5000:1
Mini PCIe
1 x Mini PCI-E slot
PCIe /PCI
1 x PCIe (x1) slot
HDD
1 x 2.5” SATA
2
Optional Functions
Optional
Touchscreen
Certifications
USB 2.0 Ports
4
VGA/DVI Ports
1 x VGA port
Speakers (1W)
2
LAN
2 x Gigabit Ethernet (isolated) interface (RJ-45)
HDMI
1 x HDMI out
DC Model
AC/DC adapter (Sinpro Model no.HPU101-107)
Input Voltage
100-240V AC, 47-63Hz, 1.2-0.5A
Output Voltage
+18 VDC,5.55 A.
Battery
3S2P 4200mAH, supports 0.5 hr. backup operation
Smart Card Reader
Complies with ISO7816-1,2,3,T=1 and T=0 protocols
WLAN
802.11a/b/g/n wire LAN mini-PCIe module &
Internal antenna
RFID
13.56 MHz with ISO-15693 & ISO-14443°/B and
active tag function
Bluetooth
Integrated Bluetooth v2.0 + EDR
Type
Analog Resistive
Resolution
Continuous
Light Transmission
80%
Controller
RS-232 interface (uses COM6)
Durability
35 million touches
UL/TUV/CB, ANSI/AAMI ES60601-1/EN60601-1/IEC60601-1, CE &
FCC Class B certified
Temperature
0 ~ 40°C (32 ~ 104°F) (Operating)
-20 ~ 60°C (Storage)
-20 ~ 60°C (Transportation)
Humidity
10 ~ 95% @ 40°C (non-condensing)
5 ~ 95% (non condensing) (Storage)
5 ~ 95% (Transportation)
Pressure
700-1013 hPa (Operation)
375 mmHg to 760 mmHg (Storage)
375 mmHg to 760 mmHg (Transportation)
Water/dust
Resistance
IPX1 compliant
IP65 front panel
Shock Resistance
20G peak acceleration (11ms duration)
Dimensions
(W x H x D)
550 x 370 x 65 mm (13.70" x 11.22" x 3.62")
Weight
7 kg (15.24 lb.)
Environment
Physical
Characteristics
Platform & utility
XP Professional, Windows 7, SUSI
3
POC-W211 User Manual
General Information
Power Supply
1 x RS-232 (isolated) and 1 x RS-232/422/485
(isolated) serial port;
Chapter 1
I/O Ports
Serial Ports
1.3 Dimensions
Dimensions: 550 x 370 x 65 mm (Unit: mm)
L AN1
V GA
HDMI
L AN2
COM2
COM1
USB
DCIN
USB
Figure 1.1 Dimensions of the POC-W211
VESA Mounting: 75 x 75 mm; 100 x 100 mm
Figure 1.2 VESA Mounting of the POC-W211
Warning! Use suitable mounting apparatus to avoid risk of injury.
POC-W211 User Manual
4
Chapter 1
B C
D E
General Information
A
F G
Figure 1.3 POC-W211 Front Panel
(A)
(B.C)
(D)
(E)
(F.G)
Power
Volume Down/Up
Touchscreen Status Control
Read Light Control
Brightness Decrease / Increase
1 2
3
4
5
6
7
8
Figure 1.4 POC-W211 Back I/O
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Power DC-IN
USB ports
VGA port
HDMI out port
2 x Gigabit Ethernet interface (RJ-45)
COM2 x RS-232 (isolated) serial port
COM1 x RS-232/422/485 (isolated) serial port
Equipotential Terminal Pin
1.3.1 Optional Modules



Memory: 2GB, 4GB DDR3 1333 MHz SDRAM
HDD: 2.5" SATA HDD
Touchscreen: Analog resistive
5
POC-W211 User Manual
1.4 Point-of-Care Terminal Cleaning and
Disinfecting
During normal use of the POC (Point-of-Care Terminal) the device may become dirty
and should be regularly cleaned.
Steps:
1. Prepare cleaning agent per manufacturer's instructions or hospital protocol.
2. Wipe the POC with a clean cloth that has been moistened in the cleaning solution.
3. Wipe thoroughly with a clean cloth.
Cleaning agent list: chemical disinfectants which have been tested on the POC
No
Cleaning Agents
1
Cidex
2
Isopropyl alcohol
3
Green tinctured soap
4
Windex
5
Alcohol
6
Alcohol 70%
7
Chloride 1000PPM
8
Incidin plus
9
Incidin liquid
10
Mikrozid liquid
Caution! 


POC-W211 User Manual
Do not immerse or rinse the POC or its peripherals. If you accidentally spill liquid on the device, disconnect the unit from the power
source. Contact your Biomed Department regarding the continued
safety of the unit before placing it back in operation.
Do not spray cleaning agents on the chassis.
Do not use disinfectants that contain phenol. Do not autoclave or
clean the POC or its peripherals with strong aromatic, chlorinated,
ketone, ether, or Esther solvents, sharp tools or abrasives. Never
immerse electrical connectors in water or other liquids.
6
Chapter
2
System Setup
2
2.1 A Quick Tour of the POC-W211
Before you start to set up the POC-W211, take a moment to become familiar with the
locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below.
When you place the POC-W211 upright on the desktop, its front panel appears as
shown in Figure 2.1.
2.1.1 Front View
(2)
(1)
Figure 2.1 Front View of the Point-of-Care Terminal
Front Bezel View
(1)
LCD panel with Touchscreen option (Touchscreen Enabled: Green light)
(2)
Power symbol w/ indicator light (Power on: Green light)
POC-W211 User Manual
8
Chapter 2
2.1.2 Bottom View
(9)
(8)
(7) (6)
(4)
(5)
Figure 2.2 Bottom View
Bottom View:
(3)
Speaker
(4)
Power Button
(5)
Volume Up/Down Button
(6)
Touchscreen Status Control Button
(7)
Read Light Control Button
(8)
Brightness Increase/Decrease Bottom
(9)
LED for Book Light
2.1.3 Rear View
When you turn the Point-of-Care Terminal around and look at its rear cover, the
sunken I/O section is at the bottom of the panel PC, as shown in Figure 2.3 and Figure 2.4 (zoom view). (The I/O section includes various I/O ports, including serial
ports, VGA, HDMI, Ethernet port, USB ports and so on.)
(10)
Figure 2.3 Rear view of the Point-of-Care Terminal
9
POC-W211 User Manual
System Setup
(3)
(11) (12)
(13)
(14)
(15)
(16)
(17)
(18)
Figure 2.4 Rear view of Multi I/O ports
Rear View:
(10)
VESA mounting 100mm x 100mm or 75mm x 75mm
(11)
DC-in Jack
(12)
USB1-USB2 ports*
(13)
VGA port
(14)
HDMI port
(15)
Ethernet RJ-45 LAN1-LAN2
(16)
COM2 serial ports
(17)
COM1 serial ports
(18)
Equipotential terminal
Note!
Equipotential terminals need a link to hospital ground/earth system
before the system boots to protect operator and system.
2.1.4 Left-side View
(18)
Figure 2.5 Left side View
Left-side View:
(18)
RW-DVD-ROM (Optional)
POC-W211 User Manual
10
Chapter 2
2.1.5 Right-side View
(19)
System Setup
(20)
Figure 2.6 Right-side View
Left-side View:
(19)
USB3-USB4 ports*
(20)
Smart Card Reader (Optional)
2.2 Installation Procedures
2.2.1 Connecting the Power Cord
The POC-W211 can only be powered by a DC power adapter (SINPRO Model
no.HPU101-107). Be sure to always handle the power cords by holding the plug ends
only.
Follow these procedures in order:
1. Connect the female end of the power adapter to the DC jack of the panel PC.
(See Figure 2.7.)
2. Connect the female end of the power cord to the DC power adapter.
3. Connect the 3-pin male plug of the power cord to an electrical outlet.
Warning! The POC-W211 is supplied by a 100 watt power supply and a special
adapter as depicted as above model.
If medical adaptor is connected to the POC-W211, the customer must
ensure legal and regulatory compliance and that the device meets the
law and standards compliance requirements of this hardware.
11
POC-W211 User Manual
Switching on the power:
Push down the power button on the front panel for POC-W211. (The color indicator
turns green)
Figure 2.7 Connecting the Power Cord
2.2.2 Connecting the Ground Pin
1.
With system ready, find the equipotential terminal on the rear side of the POC.
An equipotential terminal is provided to optionally connect to a hospital ground/
earth system
Figure 2.8 POC-W211 Equipotential Terminal Pin
2.
3.
Prepare the grounding cable and the other terminal link to hospital ground/earth
system.
Figure 2.9 Grounding cable with connector
Grounding cable plug with Equipotential Terminal
POC-W211 User Manual
12
2.4 Installing System Software
Recent releases of operating systems from major vendors include setup programs
which load automatically and guide you through hard disk preparation and operating
system installation. The guidelines below will help you determine the steps necessary
to install your operating system on the panel PC hard drive.
Note!
Some distributors and system integrators may have already preinstalled system software prior to shipment of your panel PC.
If required, insert your operating system's installation or setup diskette into the external diskette drive until the release button pops out.
The BIOS supports system boots up directly from the CD-ROM drive. You may also
insert your system installation CD-ROM disk into your external CD-ROM drive.
Power on or reset the system by pressing the “F2 or Del” key to boot into BIOS menu
and adjust the boot device sequence.
You can also press F12 key when booting; a bootable device popup menu will
appear, you can select bootable device that you want. The Point-of-Care Terminal will
automatically load the operating system from the diskette or CD-ROM.
If you are presented with the opening screen of a setup or installation program, follow
the instructions on screen. The setup program will guide you through preparation of
your hard drive, and installation of the operating system.
2.5 Installing the Drivers
After installing your system software, you will be able to set up the Chipset, Graphics,
Ethernet, Audio, Touchscreen and AMT functions from your own external CD-ROM
drive. All the drivers except the CD-ROM drive driver are stored in a CD-ROM disc
entitled "Drivers and Utilities."
The standard automatic installation procedures for installing the Chipset, Graphics,
Audio, Ethernet, AMT and Touch drivers are described in Chapter 3.
The various drivers and utilities in the CD-ROM disc have their own text files which
help users install the drivers and understand their functions. These files are a very
useful supplement to the information in this manual.
13
POC-W211 User Manual
System Setup
Your POC-W211 was probably set up and configured by your dealer prior to delivery.
You may still find it necessary to use the BIOS (Basic Input-Output System) setup
program to change system configuration information, such as the current date and
time or your type of hard drive. The setup program is stored in read-only memory. It
can be accessed either when you turn on or reset the panel PC, by pressing the “F2
or Del” key on your keyboard immediately after powering on the computer.
The settings you specify with the setup program are recorded in a special area of
memory called CMOS RAM. This memory is backed up by a battery so that it will not
be erased when you turn off or reset the system. Whenever you turn on the power,
the system reads the settings stored in CMOS RAM and compares them to the
equipment check conducted during the power on self-test (POST). If an error occurs,
an error message will be displayed on screen, and you will be prompted to run the
setup program.
Chapter 2
2.3 Running the BIOS Setup Program
For your reference, the directories of drivers on the "Drivers and Utilities" CD-ROM
are located as follows:
XP Driver List:
These drivers are located in the driver CD\Driver\XP folder
Please follow the sequence below to install driver.
Install Sequence Folder Name
Note
1
Chipset
Please install chipset driver first.
2
Graphics
After graphics driver installation, please
install Microsoft .NET Framework before
reboot.
3
Microsoft .NET Framework 3.5
sp1
4
LAN
5
Audio
6
AMT
7
Touch
Please install internal resistive touch
controller to COM6.
8
Option
Please install optional device in related
folder
Note!
These XP drivers are all 32-bit version.
WIN7 64-bit Driver List:
These drivers are located in the driver CD\Driver\WIN7 64bit folder
Please follow the sequence below to install driver.
Table 2.1: The file directory on "Drivers and Utilities" CD-ROM
Install Sequence Folder Name
Note
1
Chipset
Please install chipset driver first.
2
Graphics
3
LAN
4
Audio
5
AMT
6
Touch
Please install internal resistive touch controller to COM6.
7
Option
Please install optional device in related
folder
Note!
These WIN7 drivers are all 64-bit version.
POC-W211 User Manual
14
The drivers and utilities used for the POC-W211 panel PCs are subject
to change without notice. If in doubt, check Advantech's website or contact our application engineers for the latest information regarding drivers
and utilities.
Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following
information ready before you call:
 Product name and serial number
 Description of your peripheral attachments
 Description of your software (operating system, version, application software,
etc.)
 A complete description of the problem
 The exact wording of any error messages
 Symptoms, photo or video if available.
Guidance and Manufacturer’s Declaration – Electromagnetic Emissions
The model POC-W211 is intended for use in an electromagnetic environment as specified
below. The customer or the user of the POC-W211 should assure that it is used in such an
environment.
Compliance
Electromagnetic Environmental Guidance
RF emissions
CISPR 11
Group 1
The model POC-W211 uses RF
energy only for its internal function. Therefore, its RF emissions
are very low and are not likely to
cause any interference in nearby
electronic equipment.
RF emissions
CISPR 11
Class B
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Not applicable
Emissions Test
15
The model POC-W211 is suitable
for use in all establishments,
including domestic establishments
and those directly connected to
the public low-voltage power supply network that supplies buildings
used for domestic purposes.
POC-W211 User Manual
System Setup
Troubleshooting
When system behaves abnormally, such as:
1. Failure to power on
2. Failure to power off
3. Power LED ON but no DC power output
4. AC power in and all switches ON, but system doesn't power on
Chapter 2
Note!
Recommended Separation Distances Between
Portable and Mobile RF Communications Equipment and the POC-W211
POC-W211 is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the model POC-W211 can help
prevent electromagnetic interference by maintaining a minimum distance between portable
and mobile RF communications equipment (transmitters) and the model POC-W211 as
recommended below, according to the maximum output power of the communications
equipment.
Rated Maximum
Output Power of
Transmitter
W
Separation Distance According to Frequency of Transmitter
m
150 kHz to 80 MHz
d = 1,2 P
80 MHz to 800 MHz
d = 1,2 P
800 MHz to 2,5 GHz
d = 2,3 P
0,01
0,12
0,12
0,23
0,1
0,38
0,38
0,73
1
1,2
1,2
2,3
10
3,8
3,8
7,3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation in the table above
applicable to the frequency of the transmitter, where P is the maximum output power rating
of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range
applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reflection from structures, objects and people.
POC-W211 User Manual
16
POC-W211 is intended for use in the electromagnetic environment specified below. The
customer or the user of the model POC-W211 should assure that it is used in such an environment.
Electromagnetic Environmental Guidance
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood, concrete or ceramic tile. If floors
are covered with synthetic
material, the relative humidity
should be at least 30%.
±2 kV for power
supply lines
±2 kV for powersupply lines
IEC 61000-4-4
±1 kV for input/output lines
±1 kV for input/
output lines
Surge
IEC 61000-4-5
±1 kV line(s) to
line(s)
±2 kV line(s) to
earth
±1 kV line(s) to
line(s)
±2 kV line(s) to
earth
<5% UT (>95% dip
in UT) for 0,5 cycle
<5% UT
(>95% dip in
UT) for 0,5
cycle
Electrostatic discharge (ESD)
IEC 61000-4-2
Electrical fast
transient/burst
Interruptions and
voltage variations on power
supply input lines
IEC 61000-4-11
IEC 60601 Test
Level
40% UT
(60% dip in UT)
for 5 cycles
70% UT
(30% dip in UT)
for 25 cycles
<5% UT
(>95% dip in UT)
for 5 sec
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
3 A/m
40% UT (60%
dip in UT) for 5
cycles
70% UT (30%
dip in UT) for
25 cycles
Main power quality should be
that of a typical commercial or
hospital environment.
Main power quality should be
that of a typical commercial or
hospital environment.
Main power quality should be
that of a typical commercial or
hospital environment. If the
user of the model POC-W211
requires continued operation
during main power interruption, it is recommended that
the model POC-W211 be
powered from an uninterruptible power supply or a battery.
<5% UT
(>95% dip in
UT) for 5 sec
3 A/m
Power frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical commercial or hospital environment.
NOTE UT is the A.C. main voltage prior to application of the test level.
17
POC-W211 User Manual
System Setup
Compliance
Level
Immunity Test
Chapter 2
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity
The model POC-W211 is intended for use in the electromagnetic environment specified
below. The customer or the user of the model POC-W211 should assure that it is used in
such an environment.
Immunity
test
IEC 60601 Test
Level
Compliance
Level
Electromagnetic Environmental
Guidance
Portable and mobile RF communications equipment should be used
no closer to any part of the model
POC-W211, including cables, than
the recommended separation distance calculated from the equation
applicable to the frequency of the
transmitter.
Recommended Separation Distance
d = 1,2 P
d = 1,2 P 80 MHz to 800 MHz
Conducted
RF
IEC 61000-46
Radiated RF
IEC 61000-43
3 Vrms
150 kHz to 80
MHz
3 V/m
80 MHz to 2,5
GHz
d = 2,3 P 800 MHz to 2,5 GHz
Vrms
V/m
where P is the maximum output
power rating of the transmitter in
watts (W) according to the transmitter manufacturer and d is the recommended separation distance in
meters (m).
Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be
less than the compliance level in
each frequency range. b
Interference may occur in the vicinity of equipment marked with the following symbol:
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption
and reflection from structures, objects and people.
POC-W211 User Manual
18
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the POC-W211 is used exceeds
the applicable RF compliance level above, the POC-W211 should be observed to verify
normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the unit.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Chapter 2
a
System Setup
19
POC-W211 User Manual
POC-W211 User Manual
20
Chapter
3
Driver Installation
3
3.1 Introduction
The POC-W211 supports "one key" driver installation. User can just click one button
to install all drivers.
Warning! Please use clean OS to install this auto installation, otherwise, it might
cause un-expect error.
3.2 Automatic Driver Installation
1.
2.
Double Click "InstallAll.exe" in D:\Driver\ folder. The Install dialog will appear.
Please follow the instruction to install the driver
POC-W211 User Manual
22
Chapter
4
4
Utilities and Hot Fixes
4.1 Introduction
The POC-W211 system needs specific utilities or hot fixes to support special functions.
4.2 Wakeup by External USB Device at S3 Resume
(Wakeup)
POC-W211 supports three different sleep (suspend) modes; they are:
1. S1: Power On Suspend: system will stop the clock, turn off LCD backlight, but
keep all power on. The user can press any key (by mouse or keyboard) to wake
the system up.
2. S3: Suspend to RAM: system will stop the clock, turn off most power rails but
not power to memory. It will save all necessary information to memory.
In this sleep mode, Windows XP needs a hot fix to wake the system up via USB
mouse or keyboard. Otherwise, only the power button can be used.
3. S4: Suspend to Disk (Hibernation): system will stop the clock, turn off most
power, including power to memory. It will save all necessary information to hard
disk. In this sleep mode, the user needs to press the power button to wake the
system up.
4.2.1 Installation for Windows XP
This utility is an optional tool for Windows XP only. It needs to be installed only if the
USB wakeup function is needed.
Please don't install it on WIN7 OS.
1. Double click the "USBRG.REG" in Driver CD:\Utility\USB folder
2. Click "Yes" to update the registry.
3. Click "OK" to close the successfully installation information window.
POC-W211 User Manual
24
Chapter
5
5
Operation and Safety
Information
5.1 General Safety Guide
For your own safety and that of your equipment, always take the following precautions.
Disconnect the power plug (by pulling the plug, not the cord), from your computer if
any of the following conditions exists:
 The power cord or plug becomes frayed or otherwise damaged
 You spill something into the case
 Your computer has been dropped or the case has been otherwise damaged
 You suspect that your computer needs service or repair
 You want to clean the computer or screen
 You want to remove/install any parts
5.2 Protecting Your Optical Drive
To keep your optical drive working properly:
 Position your computer so that the drive tray doesn't bump into anything when it
opens.
 Close the drive when you're not using it.
 Do not put anything on the drive tray when it is open.
 Do not touch the optical drive lens with your fingers. Do not wipe the lens with a
paper towel or other abrasive surface.
5.3 Thermal
The vent hole of the POC-W211 rear cover functions as a cooling air flow inlet and
outlet. These air inlets and outlets transfer heat from inside the computer to the
cooler air outside. Do not block these holes/vents with any soft material.
When using your POC-W211 system, it is normal for the rear metal heatsink to get
warm. The rear metal heatsink of the POC-W211 functions as a cooling surface that
transfers heat from inside the computer to the cooler air outside. Do not block this
heatsink with any soft material.
Warning! Do not place your POC-W211 system on a pillow or other soft material
when it is on, as the material may block the airflow and cause the computer to overheat.
5.4 Disconnect the Power
The only way to disconnect power completely is to unplug the adapter power cord.
Make sure at least one end of the power cord is within easy reach so that you can
unplug the computer when you need to.
Warning! Your AC cord came equipped with a three-wire grounding plug (a plug
that has a third grounding pin). This plug will fit only a grounded AC outlet. If you are unable to insert the plug into an outlet because the outlet is
not grounded, contact a licensed electrician to replace the outlet with a
properly grounded outlet. Do not defeat the purpose of the grounding
plug.
POC-W211 User Manual
26
POC-W211 User Manual
Operation and Safety Information
27
Chapter 5
Warning! Never push objects of any kind into this product through the openings in
the case. Doing so may be dangerous and result in fire or a dangerous
electric shock.
Never place anything on system case before turning off the computer.
Never turn on your computer unless all of its internal and external parts
are in place.
Operating the computer when it is open or missing parts can be dangerous and can damage your computer.
POC-W211 User Manual
28
Chapter
6
6
PCM-8709 Connector
Map and Table
6.1 Motherboard Top Side
6.2 Motherboard Bottom Side
POC-W211 User Manual
30
Chapter 6
Table 6.1: MB Connector Table
Description
1
LVDS Connector
2
EC SMBUS Connector
3
FAN (Reserved)
4
SATA 0 Connector
5
LED Driver/Inverter Connector
6
SATA 0 Power Connector
7
DDR3 SODIMM A Socket
8
DDR3 SODIMM B Socket
9
SATA 1 Connector
10
SATA 1 Power Connector
11
5-Wire Resistive Touch Connector
12
USB (Reserved)
13
BIOS Flash Port (Reserved)
14
Mini PCIe Socket
15
RFID Connector
16
Front Button Board Connector
17
Port 80 Debug Port
18
Smart Card Connector
19
RTC Battery Connector
20
Power Button (Reserved)
21
USB (Reserved)
22
Right Speaker Connector
23
Left Speaker Connector
24
PCIex1 Slot
25
EC Debug Port (Reserved)
26
12V (Reserved)
27
Bluetooth Connector
28
I/O Board Slot
PCM-8709 Connector Map and Table
No.
6.3 I/O Board
* All connectors are located on the top side
31
POC-W211 User Manual
Table 6.2: I/O Connector Table
No.
Description
1
USB Connector (Reserved)
2
USB Connector
3
Internal Backup Battery Connector
4
DCIN
5
USB I/O
6
VGA
7
Reset EC Button
8
HDMI
9
LAN1 (iAMT)
10
LAN2
11
COM2
12
COM1
POC-W211 User Manual
32
Chapter
7
7
PCM-8709 Jumper
Settings
7.1 Motherboard
* All Jumpers located at top side
Figure 7.1 PCM-8709 Motherboard Top Side
7.2 I/O Board
* All Jumpers located at top side
Figure 7.2 PCM-8709 I/O Top Side
POC-W211 User Manual
34
Chapter 7
Table 7.1: Jumper Settings:
Setting
Function
CN1
Clear CMOS
CN2
Clear ME
CN3
VBIOS Setup
CN4
ME Manufacturing Mode
System Reset
CN12
LVDS Voltage Select
IO:
CN12
COM1 RS-232/422/485 output type setting
Table 7.2: CN: Clear CMOS
Setting
Function
(1-2)
Clear CMOS Setup
(No Connect)
Normal Operation (Default)
Table 7.3: CN2: Clear ME
Setting
Function
(1-2)
Clear ME Setup
(No Connect)
Normal Operation (Default)
35
POC-W211 User Manual
PCM-8709 Jumper Settings
CN8
C
Table 7.4: CN3: VBIOS Setup
Setting
Function
(3-4)(5-6)
Panel Resolution: 24-bit single channel 1024x768
(1-2)(5-6)
Panel Resolution: 24-bit dual channel 1280x1024
(1-2)(3-4)(5-6)
Panel Resolution: 24-bit dual channel 1680x1050
(5-6)
Panel Resolution: Manual setting
(3-4)
Panel Resolution: 24-bit dual channel 1920x1080 (Default)
(1-2)
Panel Resolution: 24-bit single channel 1366x768
(1-2)(3-4)
Reserved
(No Connect)
Reserved
Table 7.5: CN3: Select Boot Main Display Setup
Setting
Function
(7-8)
Set VGA as main display at bootup
(No Connect)
Set LVDS as main display at bootup (Default)
Table 7.6: CN4: ME Manufacturing Mode
Setting
Function
(1-2)
ME Manufacturing Mode
(No Connect)
Normal Operation (Default)
POC-W211 User Manual
36
Chapter 7
Table 7.7: CN8: System Reset
Setting
Function
(1-2)
System Reset
(No Connect)
Normal Operation (Default)
Setting
Function
(1-2)
LVDS Power use 5V (Default)
(2-3)
LVDS Power use 3.3V
Table 7.9: CN12 (IO): COM1 RS-232/422/485 Output Type Settings
Setting
Function
(5-6), (7-9), (8-10),
(13-15), (14-16)
RS-232 (Default)
(3-4), (9-11)(10-12),
(15-17)(16-18)
RS-422
(1-2), (9-11)(10-12),
(15-17)(16-18)
RS-485
37
POC-W211 User Manual
PCM-8709 Jumper Settings
Table 7.8: CN12 (MB): LVDS Voltage Select
POC-W211 User Manual
38
Chapter
8
8
Front Bezel Button
8.1 Introduction
This section outlines the POC-W211 front button function descriptions.
8.1.1 Front Button Map
Button Description:
Power button
Reduce volume
Increase volume
Touch disable
Press this button to power on/off system. When system
ON, this icon will become green. The LED will turn off
when system is off.
Press this button to reduce speaker and headphone volume.
Press this button to increase speaker and headphone volume.
Press this button to disable/enable touch function. When
touch function is enabled, this icon will become green.
When touch function is disabled, this LED will be off.
Read light
Press this button to enable/disable read light.
Reduce brightness
Press this button to reduce LCD backlight brightness.
Increase brightness
Press this button to increase LCD backlight brightness.
Combination Button:
The backlight off function is a special function. When you press both the reduce
brightness and increase brightness buttons at the same time for half a second, the
LCD backlight will turn off. Pressing both buttons again for a half second will turn on
the LCD backlight.
When the backlight is off, the POC-W211 system will still run. There will not be an
impact to any operating programs.
This backlight off function can be used in a hospital environment.
If an operator needs to check X-rays in a dark room environment, the operator can
quickly turn off the backlight to prevent interference.
An operator can turn off the backlight at night to prevent disturbing a sleeping patient.
POC-W211 User Manual
40
Chapter
9
9
POC-W211 Advanced
BIOS Function
9.1 Introduction
This section introduces the advanced functions of the POC-W211 BIOS menu.
1. Power Button Function Enable/Disable
You can enable/disable power button functions from the BIOS menu.
If you disable the power button in S0 (System ON) status, the power button will
not work. This prevents a user from turning a system off by the power button,
preventing accidental shutdown of the system. In this mode software is required
to turn off the system.
2.
3.
BIOS Menu location:
BIOS Menu - Advanced - Embedded Controller Configuration - Power Button
Function
Enable: Power button function works when system in S0 (System ON) status. (Default)
Disable: Power button function does not work when system in S0 (System
ON) status.
Press power button 5 seconds or more to trigger power button.
Brightness Button Control
You can enable/disable LCD Backlight button function in BIOS menu.
If you disable the LCD Backlight button, this button will not work, preventing a
user from adjusting LCD backlight luminance. This function can prevent accidentally touching the LCD backlight button and inadvertently adjusting LCD
backlight luminance.
BIOS Menu location:
BIOS Menu - Advanced - Embedded Controller Configuration - Brightness Button Control
Enable: Front bezel LCD Backlight adjust button control functions work.
(Default)
Disable: Front bezel LCD Backlight adjust button control functions do not
work.
Volume Button Control
You can enable/disable Front Volume button functions in BIOS menu.
If you disable the Front Volume button, this button will not work, preventing a
user from adjusting speaker volume. This function can prevent accidental volume adjustments.
BIOS Menu location:
BIOS Menu - Advanced - Embedded Controller Configuration - Volume Button Control
Enable: Front bezel volume adjust button control functions work. (Default)
Disable: Front bezel volume adjust button control functions do not work.
POC-W211 User Manual
42
EC Beep Function
You can enable/disable EC beep function in BIOS menu.
If you disable the EC beep function, EC will not generate a beeping sound when
you press front bezel button.
5.
Setup Popup Menu F12
You can enable/disable F12 key Setup popup menu in BIOS menu.
When you press F12 key in bootup, BIOS will display a bootable device menu
and you can select the proper boot device that you want.
BIOS Menu location:
BIOS Menu - Boot - Setup Popup Menu F12
Enable: Press F12 key at bootup displays popup menu (Default)
Disable: Press F12 key at bootup does not display popup menu
43
POC-W211 User Manual
POC-W211 Advanced BIOS Function
BIOS Menu location:
BIOS Menu - Advanced - Embedded Controller Configuration - EC Beep Function
Enable: Beeping sound when front bezel button pressed. (Default)
Disable: No beeping sound when front bezel button pressed.
Chapter 9
4.
POC-W211 User Manual
44
Appendix
A
A
POC-W211 VESA
Mounting
A.1 Install VESA Mounting
The POC-W211 also provides standard VESA mounting to help system integrators
conveniently integrate the panel PC into their system.
Never use mounting brackets except as provided by Advantech to prevent unreliable
mounting of the POC-W211. VESA mount installation should be carried out by a professional technician; please contact a service technician or your retailer if you need
this service.
Installation instructions follow:
1. First attach wall-mounting to the heat-sink of the POC-W211, securing it in place
with the four Phillips-head screws provided.
2. Mount the unit on the wall, stand or other flat surface.
Warning! Be sure to secure the screws of the mounting bracket tightly. A loose
joint between the POC-W211 and mounting bracket may create danger
of injury.
Figure A.1 VESA Mounting 75x75mm, 100x100 mm
POC-W211 User Manual
46
Appendix A POC-W211 VESA Mounting
POC-W211 User Manual
47
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement