User Guide

ECOMBI HHR

Smart Storage Heaters

ECOHHR20 | ECOHHR30 | ECOHHR40

Please read these instructions carefully before installing or using this appliance for the first time.

IMPORTANT INFORMATION

• Please read all the instructions carefully before

installing or using the heater for the first time and

retain for future use.

• CAUTION – Some parts of this product can become

very hot and cause burns. Particular attention must

be given where children and vulnerable people

are present.

• Children should be supervised to ensure they do

not play with the heater. Extreme caution is

necessary when any heater is used by or near

children or invalids and whenever the heater is

left operating unattended.

• This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning the

use of the appliance in a safe way and understand

the hazards involved. Cleaning and user

maintenance must not be done or carried out

by children without supervision.

• Children ages from 3 years and less than 8 years

must only switch the appliance on/off provided that

it has been installed in its intended normal operating

position and they have been given supervision or

instruction concerning use of the appliance in a

safe way and understand the hazards involved.

They also must not plug in, regulate and clean the

appliance or perform user maintenance.

• Children of less than 3 years should be kept away

unless continuously supervised.

• Do not operate any heater after it malfunctions.

Disconnect and Isolate from the electrical supply

and have the heater inspected by a competent

electrician or approved service agent before reusing.

• Do not use the heater outdoors.

• To disconnect the heater, turn off the isolator

switches and at the consumer unit.

• Do not insert or allow foreign objects to enter any

ventilation or exhaust openings as this may cause

electric shock, fire or damage to the heater.

• Air inlets and outlets provide proper operation of the

appliance and prevent its overheating. DO NOT cover

or block the air intake and outlet grills.

• Use this heater only as described in this manual.

Any other use is not recommended by the

or injury to persons.

manufacturer and may cause fire, electric shock

• This guide must be kept and given to any new user.

Balancing element output

Storage heater element rating

Charge period

Charging (7h)

Connection

Frequency

Length

Height

Width

Weight (including blocks)

Number of blocks (6kg)

W

W

ECOHHR20 ECOHHR30 ECOHHR40

550

1742

7h

820

2613

7h

1100

3484

7h kWh 12.2

240V~

Hz 50-60

18.3

240V~

50-60

24.4

240V~

50-60 cm 72 cm 76 cm 19.5

Kg 97

12

95

76

19.5

140

18

117

76

19.5

183

24

Content for Installation Instruction

1. ECOHHR Important Information and Content

Information.

2. Warning Messages & Unpacking.

3. Removing Front Panel & Wiring.

4. Removing Microtherm & Installing Bricks.

5. Refitting Microtherm & Front Panel.

6. Relocation, Resetting Safety cut-out and Main components list.

7. Connection and Disconnection,

Control panel layout

8. General Settings - Initial Off-Peak Setup

9. Resetting to Factory defaults and troubleshooting

10. Connection Diagram HHR20

11. Connection Diagram HHR30

12. Connection Diagram HHR40

13. Single Power Supply Connection

14. Supplier and Contact Details

SAVE THESE INSTRUCTIONS Elnur UK Ltd, Unit 1 Brown Street North, Leigh, WN7 1BU

Customer Help Line

01942 670119

Technical Support

01942 670119 (Option 2)

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 2

USER OPERATING INSTRUCTIONS

Note

This heater can be connected to the standard two electrical supplies Economy and 24hr supply or one single Economy/24hr supply.

Connection and Disconnection

Each ECOHHR storage heater has its own power switch and is located on the right side panel. The power switch is used to turn the heater ON and OFF.

If this switch is turned OFF then the storage heater will not take a charge when the off-peak supply is on and will not give out any heat. Therefore, it is important to make sure this is turned ON at all times.

Each ECOHHR storage heater requires two electrical supplies. One is an economy tariff supply (off peak or restricted supply) and the other is a 24hr supply

(on peak or unrestricted supply). However, the Elnur

ECOHHR is capable of utilising a single economy/24hr supply by using the supplied link cables. Modification to the distribution board may be required if supplied via radial circuits.

Connection from the economy supply or economy/24hr supply to the heater should be via a 20Amp double pole isolator switch. (Radial circuits)

Connection from the 24hr supply (on peak or unrestricted supply) to the heater should be via a fused double pole isolator switch or a fused RCD isolator switch, depending on the installation.

User Control Panel

You will find the keypad on the top right side on the heater. This easy to use keypad only has four buttons, however these four buttons can be used in different ways to give you many functions and will be explained in more detail in later sections.

Basic Key functions:

This button is used to set the

‘Comfort’ temperature. Default is 21°C.

&

&

This button is used to set the

‘Economy’ temperature. Default is 18°C.

This button is used to decrease values.

This button is used to increase values.

Pressing these buttons together will allow you to set the Day and Time.

Pressing these buttons together will allow you to set the weekly program.

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 3

USER OPERATING INSTRUCTIONS dAy1 09:15

Setting the Day/Time

The ECOHHR storage heater has been preset with the

Day and Time however you will need to adjust this with summer and winter times (when the clocks go forward and back).

To check the Day and Time on your ECOHHR storage heater follow these steps. dAy1

and Press and Release the sun button and the minus button together and the display will first show the Day and then the current Time. dAy1 09:15

10: 15 09: 15 dAy1

09: 15

09: 15

09: 08

10: 15

If the Day or Time are incorrect and you want to change then follow these steps.

and Press and Hold the sun button and the minus button together until the Day is displayed and starts to flash.

Use the plus or minus buttons to adjust to the current Day.

and Press and Release the sun button and the minus button together to set the Day and move onto the Time.

The Hour will now start to flash.

Use the plus or minus buttons to adjust to the current hour time.

09: 15 09: 08

and Press and Release the sun button and the minus button together to set the Hour and move onto the Minutes.

The Minutes will now start to flash. Use the plus or minus button to adjust to the current minutes time.

and Press and Release the sun button and the minus button together to set the Minutes and to finish.

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 4

USER OPERATING INSTRUCTIONS

Setting the Comfort Temperature Level

The ECOHHR storage heater has been preset with a

Comfort temperature level of 21°C.

To increase or decrease the Comfort temperature level please follow these steps.

Sun 21:0

Press and Release the sun (comfort) button

The word SUN will be displayed for a short time and then the current set temperature for the comfort level will start to flash.

Use the plus or minus button to adjust the comfort temperature.

Sun

22.0

21:0

Press and Hold the sun button again to set the new comfort temperature level.

22.0

Noon

Noon

16.0

18.0

18.0

Setting the Economy Temperature Level

The ECOHHR storage heater has been preset with an

Economy temperature level of 18°C.

To increase or decrease the Economy temperature level please follow these steps.

Press and Release the moon (economy) button

The word Noon will be displayed for a short time and then the current set temperature for the economy level will start to flash.

Use the plus or minus button to adjust the economy temperature.

16.0

Press and Release the moon (economy) button again to set the new economy temperature level.

!

Please note adjusting the default set temperatures can result in higher running costs. We recommend a 3˚C - 5˚C max difference between the economy and comfort temperature.

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 5

USER OPERATING INSTRUCTIONS

Default weekly program set for all 7 days.

21°C

18°C

00:00

7:00am 22:00pm

24:00

Default Weekly Program

The ECOHHR storage heater has been preset with a weekly program designed to give comfort level heating throughout the day and is based on the following times.

From 00:00 till 07:00am the program runs in economy mode at 18°C, from 07:00am till 22:00pm the program runs at the Comfort temperature of 21°C and from

22:00pm till 24:00pm will run in economy mode.

Pro9

Pro9

Pro9 dAy1 dAy1 dAy1

Setting the Weekly Program

If you wish to change the default weekly program then follow the next steps. Please note by changing the programmed times you may increase the running costs and reduce the efficiency of the heater.

We suggest that you first make a note of the times when you want the heater to be at the Comfort and Economy temperatures.

Press and Release the moon (economy) button and the plus button at the same time. The word ProG will display for a short time and then dAY1 will flash. dAy1 dAy1 dAy1

00:00

00:00

00:00

Use the or button to select the day you wish to change the programming for. Then Press and Release the moon (economy) button and the plus button at the same time to select and enter the program for that day.

00:00

00:00

00:00

Noon

Noon

Noon

The display will now flash between the time intervals

00:00 and the set temperature level Noon

(Economy setting)

Sun

Sun

Sun

00:30

00:30

00:30

00:00

00:00

00:00

Noon

Noon

Noon

If you wish to change the temperature level from Noon

(Economy) to Sun (Comfort) for this 30 minute segment

00:00 to 00:30 then Press the Sun (comfort) button.

The display will now flash between the time interval

00:00 and Sun(Comfort).

Now Press the Plus button to move to the next 30 minute segment. The display will now flash between the time interval 00:30 and this temperature level

(If you want to keep the current setting of Noon

(economy) or Sun(Comfort) then just Press the plus button to move to the next 30 minute segment.)

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 6

USER OPERATING INSTRUCTIONS

Sun

Sun

Sun

Sun

00:30

00:30

00:30

00:30

Setting the Weekly Program - continued

If you wish to change the temperature level from Noon

(Economy) to Sun (Comfort) for this 30 minute segment

00:30 to 01:00 then Press the sun (comfort) button.

The display will now flash between the time interval

00:30 and Sun (Comfort).

01:00

01:00

01:00

Noon

Noon

Noon

Noon

Now Press the Plus button to move to the next

30 minute segment. The display will now flash between the time interval 00:30 and this temperature level.

Repeat the above steps, selecting either the Sun

(Comfort) temperature or Noon (Economy) temperature and pressing the Plus button to move to the next 30 minute segment. dAy1 dAy1 dAy1 dAy1

Repeat this until you go through all the 30 minute segments and the display shows dAY 1 again.

At this point you can either Press the Plus button and repeat the above for day 2 and the other days or copy day1 to day2, day2 to day3, day3 to day4, and so on. dAy1 dAy1 dAy1 dAy1

Cp12

Cp12

Cp12

Cp12

Setting the Weekly Program - Copying Days

To copy dAY1 to dAY2 . (while on the day you want to copy) press and hold the button until CP12

(copy day 1 to day 2) is displayed and then release.

After a short time the display will show dAY1 again.

dAy1 dAy1 dAy1 dAy1 dAy2 dAy2 dAy2

Press and Release the button to move to day 2, dAY2 is now displayed.

dAy2 dAy2 dAy2 dAy2

CP23

CP23

CP23

To copy dAY2 to dAY3 .

Press and Hold the Plus button until CP23

(copy day 2 to day 3) is displayed and then release.

After a short time the display will show dAY2 again.

dAy2 dAy2 dAy2 dAy2 dAy3 dAy3 dAy3

Repeat as above and go through copying each day.

Once you have gone through all the days the display will show the set temperature as you have programmed.

Press and Release the button to move to day 3, dAY3 is now displayed.

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 7

USER OPERATING INSTRUCTIONS

Sun

Economy Mode Override Function

At some point you may wish to temporarily override your current running program from Economy to the

Comfort temperature.

To override the Economy Mode you’ll need to follow these steps.

Press and Hold the sun (comfort) button until the word Sun is displayed. The heater will now maintain the comfort temperature until the next programmed change. At which point the heater will then continue to run your current program.

[--]

Sun

Control Panel Child Lock Function

The ECOHHR storage heater has a built-in child lock function that allows you to block any unwanted changes to the heaters settings by disabling the control panel.

21.0

[--]

To lock the control panel:

Press and Hold the plus and minus buttons until [ - - ] is displayed. The heaters control panel is now locked and will now not allow anyone to use or change anything.

21.0

To unlock the control panel:

Press and Hold the plus and minus buttons until the temperature is displayed. The heaters control panel is now unlocked and will now allow anyone to use again.

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 8

USER OPERATING INSTRUCTIONS

20.6

20.6

20.6

ECOHHR Current Status Function

The ECOHHR has a function that allows you check the current status of the heater. This function allows you to see what temperature the heater is currently measuring the room to be, the current core temperature, the air temperature at the grille, the percentage of charge the heater tried to take last period and how long the balancing element has been used for during the last on peak time.

To check the current Status :

Press and Release the sun and the moon buttons together. The display will now show the current room temperature that the sensor is measuring.

C146

C146

C146

Now Press and Release the plus button to see the current Core temperature.

A23

A23

A23

Now Press and Release the plus button to see the current Air temperature at the grille.

ST80

ST80

ST80

Now Press and Release the plus button to see the amount of the last charge percentage the heater did.

00:00

00:00

00:00

Now Press and Release the plus button to see how long the balancing element has been on during the last 24hrs.

Cleaning your ECOHHR

Before cleaning, make sure the power has been turned off and the heater is cold to touch.

Occasionally, clean dust with a dry, soft cloth.

Do NOT use any solvent or abrasive products for cleaning.

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 9

PRODUCT FICHE

MODEL(S): GABARRON ECOHHR20, ECOHHR30, ECOHHR40

ErP

Symbol ECOHHR20

Value

ECOHHR30 Item

Heat Output

Nominal heat output

Minimum heat output

Maximum continuous heat output

Auxiliary electricity consumption

At nominal heat output

At minimum heat output

In standby mode

P

nom

P

min

0.8

N.A.

P

max, c 0.8

el

max 0.000

el

min 0.000

el

sb <0.0005

1.2

N.A.

1.2

0.000

0.000

<0.0005

ECOHHR40 Unit

1.6

N.A.

1.6

0.000

0.000

<0.0005

kW kW kW kW kW kW

Item

Type of heat input

Electronic heat charge control with room and/or outdoor temperature feedback

Type of heat output / room temperature control

Electronic room temperature control plus week timer

Other control options

Room temperature control, with open window detection

With distance control option

With adaptive start control

Value. All models

Yes

Yes

Yes

Yes

Yes

Contact details

ELNUR, UK

Unit 1, Brown Street North, Leigh, Wigan, WN7 1BP

Commission Regulation (UE) 2015/1188 of 28 April 2015. Ecodesign requirements for electric storage local space heaters.

Elnur powered by Gabarrón | ECOMBI HHR | User Guide 10

Supplier:

ELNUR UK Ltd.

Unit 1, Brown Street North

Leigh, Lancashire, WN7 1BU.

+44(0)1942 670119 [email protected]

Manufactured by:

ELNUR S.A.

Travesía de Villa Esther, 11 28110, Algete

Madrid Telephone: +34 916281440

15190020 R2 | EN

The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product. These instructions are only valid in the EU member states.

www.elnur.co.uk

© All rights reserved. As part of the continuous improvement policy, ELNUR, S.A. reserves the right to alter or modify any specifications without notice.