Techni Mobili RTA-8807-WN 55 in. Wenge Composite TV Stand Assembly Instructions
Techni Mobili RTA-8807-WN is a versatile and practical storage solution that can be used in various settings, including homes, offices, and commercial spaces. This unit features a sturdy construction with wooden panels and metal reinforcements, providing ample support for your belongings. With its adjustable shelves, you can customize the storage space to accommodate items of different sizes and shapes. The drawers provide additional storage capacity for smaller items or those you want to keep out of sight.
Advertisement
Advertisement
MODEL RTA-8807
ASSEMBLY INSTRUCTIONS
Thank you for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit has been completely assembled
.
Imported By
P.2
๐ x1
Main panel
RTA-8807
MAIN PARTS LIST
๐ x1
Bottom panel
๐ x1
Middle shelf
P.2
๐ x1
Left panel
๐ x1
Right panel
๐ x1
Upper divider panel
๐ x1
Lower divider panel
๐ x1
Bottom crossbar
๐ x1
Left frame leg
๐ x1
Right frame leg x2
Top/Bottom frame x2
Side frame
๐ x1
Middle panel
๐ x1
Adjustable panel
๐ x1
Glass door
๐ x1
Left drawer front panel
๐ x1
Right drawer front panel
๐ x2
Drawer left panel
๐ ก x2
Drawer right panel
๐ ข x2
Drawer back panel
๐ ฃ x2
Drawer support bar
๐ ค x2
Drawer bottom panel
๐ ฅ x1
Back panel
P.3
RTA-8807
MAIN PARTS LAYOUT (FOR REFERENCE):
๐
๐
๐
๐
๐
๐
๐
๐
๐
๐
๐
๐
P.3
HARDWARELIST:
Glides
Notes:
• The sliders โฑ come packaged separate from the rest of the hardware.
• You will need a screwdriver and mallet/hammer
(not included) for the assembly.
P.4
RTA-8807 P.4
โ This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware.
Cam Bolt Cam Lock
1. Screw the bolt into the corresponding panel.
2. In the other panel, insert the cam lock and align it so it can properly receive the bolt, then join both panels (the cam locks might come pre-installed in this unit).
3. The panels might have a very small gap which is normal; turn the cam lock clockwise to lock the parts together and the gap will also close.
ALIGNMENT
DIRECTION
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
• Do a quick inventory to make sure the product contains all the parts and hardware.
• Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product.
• The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto Rico,
U.S. Dependencies or other countries, please contact the supplier from where the unit was purchased.
• If during assembly you find an issue or need clarification, please contact our Customer Service for assistance.
Please refer to the CONTACT card included with the product.
• On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the assembly.
• Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or pin might strip the threads or cause damage to the part in which it is being used.
• To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly.
• Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get stuck inside the part.
• Sometimes the laminate might cover partially or entirely the hole on a panel, but the hole should still be located under the laminate.
• If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole underneath.
• If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to reveal the hole’s actual size.
P.5
RTA-8807 P.5
ASSEMBLY STEPS
STEP 1
Hardware:
โถ
Short Pins 52
Pcs
Install the wooden pins โ into the panels โถ , โท , โธ , โน , โบ , โป , โผ , โฝ , โ , โ and โ in the corresponding holes as shown in the illustrations, but make sure to use the correct holes as some are intended for other kind of hardware in subsequent steps.
MAKE SURE TO
INSERT THE PINS IN
THE CORRECT HOLES.
STEP 2
Hardware:
โท
Long Pins 2
Pcs
Insert the wooden pins โก into the top holes of panel โผ as shown.
P.6
RTA-8807 P.6
STEP 3
Hardware:
โพ
Cam bolt 22
Pcs
Attach the cam bolts โจ to the corresponding holes on the panels โถ , โน , โบ , โ , โ and
โ as shown, but make sure to use the correct holes as some are intended for other kind of hardware in subsequent steps.
MAKE SURE TO
ATTACH THE BOLTS IN
THE CORRECT HOLES.
STEP 4
Hardware:
โซ
Metal pin 4
Pcs
Insert the metal pins โช into the corresponding holes on the panels โน and โ as shown.
You can adjust the height for the shelves later on step 26.
P.7
RTA-8807
STEP 5
Hardware:
โน
3.5x15mm
8
Pcs
โฌ
Base
4
Pcs
Use screws โฃ to assemble the plastic bases โซ to the panels โน and โบ .
P.7
STEP 6 Separate all the sliders pieces โฐ according to their shape (no assembly is done here):
-The “Flat” ones go on the side panels of the unit and will be used on the next step.
-The “L” shaped go on the drawers and will be used until step 24, please set them aside.
“L shaped”: Use until step 20
LEFT
LEFT
Screws:
โธ
5x8mm 8
Pcs
โฑ
STEP 7
RIGHT
“FLAT”: Use on next step
RIGHT
(2 Sets, total 8 pcs:
4 flats, 4 L shaped)
Using screws โข , and paying close attention to the orientation of the parts, assemble:
• One of the right flat sliders โฐ to the plastic bases โซ on panel โบ .
• One of the left flat sliders โฐ to panel โ .
• The remaining flat sliders โฐ to panel โผ on both sides of the panel.
Flat, Left
(Use 2 screws)
Flat sliders
2 Left
2 Right
Attach the sliders on both sides.
Flat, Right
(Use 2 screws)
Flat, Right
(Use 2 screws)
ON ALL THE SLIDERS THE WHEEL
FACES DOWN AND TOWARDS THE FRONT
Flat, Left
(Use 2 screws)
P.8
STEP 8
RTA-8807
Loosen the screw indicated in the illustration on the hinges โฎ and separate the parts:
• The small parts โ will be used on the next step.
• The big parts โ will be used until step 17, please set them aside.
You might also need to tighten this screw a little bit.
Small parts โ will be used on next step.
P.8
STEP 9
Hardware:
โผ
10#x1/2” 4
Pcs
Hinge “a”
2
Pcs
DO NOT REMOVE THE
SCREWS FROM ANY
OF THE 2 PARTS.
Big parts โ will be used until step 21.
Assemble the small hinges โฎ โ to the plastic bases โซ on panel โน using screws โฆ as shown.
PAY ATTENTION TO THE
ORIENTATION OF THE PARTS
STEP 10
Hardware:
โพ
Cam lock 2
Pcs
1 st : Install and align the cam locks โจ into panel โธ in the locations indicated.
2 nd : Assemble the panel โ to panel โธ as shown and as explained in page 4.
3 rd : Join the panel โผ to panel โธ as shown (wooden pins enter into the holes).
PAY ATTENTION TO THE
ORIENTATION OF THE PARTS
SEE PAGE 4
(This view is from the underside of the unit)
P.9
RTA-8807
STEP 11
Hardware:
โป
5x38mm 4
Pcs
Use screws โฅ to assemble the bottom panel โท to panels โผ and โ as shown.
P.9
STEP 12
(This view is from the underside of the unit)
Join the bottom crossbar โฝ to the bottom panel โท as shown (wooden pins enter into the holes).
(This view is from the underside of the unit)
STEP 13
Hardware:
โพ
Cam lock 6
Pcs
1 st : Install and align the cam locks โจ into panels โท and โธ in the locations indicated.
2 nd : Assemble panel โน to panel โท as shown and as explained in page 4.
3 rd : Assemble panel โบ to panels โท and โธ as shown and as explained in page 4.
SEE PAGE 4
(This view is from the underside of the unit)
P.10
STEP 14
RTA-8807 P.10
Join the upper divider panel โป to the middle shelf โธ as shown (wooden pins enter in the holes).
(This view shows the unit in the normal upright position)
STEP 15
Hardware:
โพ
Cam lock 8
Pcs
1 st : Install and align the cam locks โจ into panels โน , โบ , โป and โ in the locations indicated.
2 nd : Assemble the main panel โถ to panels โน , โบ , โป and โ as shown and as explained in page 4.
(Front of panel โถ has the wooden pins, the back has the grove)
SEE PAGE 4
STEP 16
Hardware:
โพ
Cam bolt 16
Pcs
Attach the cam bolts โจ to the corresponding holes on the panels โ 1, โ 2, โพ and โฟ as shown, but make sure to use the correct holes as some are intended for other kind of hardware in subsequent steps.
MAKE SURE TO
ATTACH THE BOLTS IN
THE CORRECT HOLES.
P.11
RTA-8807 P.11
STEP 17
Hardware:
โพ
Cam locks 16
Pcs
1 st : Install and align the cam locks โจ into panels โถ , โท , โน and โบ .
2 nd : Assemble the frames โ 1 to panels โถ and โท as shown and as explained in page 4.
3rd: Assemble the frames โ 2 to panels โน and โบ as shown and as explained in page 4.
4th: Assemble the leg โพ to the bottom of panel โน and the leg โฟ to the bottom of panel โบ as shown and as explained in page 4.
SEE PAGE 4
(This view is from the underside of the unit with its front facing UP)
STEP 18
Hardware:
โฝ
Nail 20
Pcs
1 st : Insert the back panel โ sliding it thru the groves of panels โถ , โน and โบ .
2 nd : Nail the back panel โ to panel โท , and to the panels โป and โ (behind) using the line markings as guide.
HOLES FACE TOWARDS THE TOP,
FINISH SURFACE FACES TOWARDS
THE INSIDE.
(This view is from the underside of the unit with its front facing DOWN)
P.12
RTA-8807
STEP 19
Screws:
โน
3.5x15mm
4
Pcs
โฐ
L Bracket 2
Pcs
Use screws โฃ to attach the L brackets โฏ to the panels โท and โฝ as shown.
P.12
(This view is from the underside of the unit with its front facing DOWN)
STEP 20
Hardware:
โฎ
Glides 5
Pcs
Attach the nail-in glides โญ to the bottom corners of panels โน and โบ and to the center of panel โฝ .
(This view is from the underside of the unit with its front facing DOWN)
STEP 21
Screws:
โผ
10#x1/2” 4
Pcs
โฏ
Hinge “b”
2
Pcs
Assemble the big hinges โฎ โ to the glass door โ using screws โฆ as shown.
P.13
RTA-8807
STEP 22
Hardware:
โญ
Handle 1
Set
Assemble the handle โฌ to the door โ using the screws that come with it
P.13
THE HANDLE
OPENING
FACES LEFT
STEP 23
Hardware:
โพ
Cam lock 6
Pcs
For each the drawer:
1 st : Install and align the cam locks โจ into all the panels โ , โ and โ .
2 nd : Assemble the panels โ , โ and โ to panel O as shown and as explained in page 4.
3 rd : Assemble the panels โ , โ and โ to panel P as shown and as explained in page 4.
4 th : insert the panel โ thru the groves on panels โ , โ and โ .
5 th : insert the panel โ thru the groves on panels โ , โ and โ .
SEE PAGE 4
SEE PAGE 4
(This view shows the drawer with its front facing DOWN)
P.14
RTA-8807 P.14
STEP 24
Screws:
โน
3.5x15mm
8
Pcs
โบ
4x38mm 10
Pcs
“L” sliders
โฑ
2 Left
2 Right
For each the drawer:
1 st : Use screws โค to assemble the back panel โ to the side panels โ and โ from the sides, and to the support bar โ from the back.
2 nd : Assemble the “L” shaped sliders โฐ to the side panels โ and โ using screws โฃ as shown.
VERY IMPORTANT ABOUT
THE SLIDERS!
CORRECT:
Sliders don’t protrude on the bottom.
INCORRECT:
Raises the drawer 1” and won’t fit!
THE WHEEL GO
AT THE BACK
LEFT
RIGHT
STEP 25
Hardware:
โฟ
Caps 4
Pcs
โญ
Handle 2
Set
(This view shows the drawer with its front facing DOWN)
For each drawer, assemble the handles โฌ to the front panels โ , and โ respectively, using the screws that come with them, then cover the screws with the plastic caps โฉ .
HANDLE OPENING
FACES DOWN
P.15
RTA-8807 P.15
STEP 26
Hardware:
โฟ
Caps 6
Pcs
1 st : Insert the drawer with the front panel โ into the LEFT of the unit.
2 nd : Insert the drawer with the front panel โ into the RIGHT of the unit.
3 rd : Insert and place the adjustable panel โ over the metal pins on the left. You can adjust the location of the panel according to your preference.
4 th : Cover the cam locks that are visible at the front of the unit with plastic caps โฉ .
DRAWER โ TO THE LEFT.
DRAWER โ TO THE RIGHT.
STEP 27
(This view shows the unit in the normal upright position)
Assemble the door โ to the unit by joining the hinges โฎ โ (on the door) with the hinges
โฎ โ (on the plastic bases โซ ) as shown. A little adjustment might be needed if the door does not close properly, please see instructions below.
If the door does not close properly, you can adjust the alignment of the hinges by adjusting the following screws:
Adjusts the depth.
DONE! Before you start using the unit, make sure that all the screws, bolts, cam locks, etc. are properly tightened, and read all the warnings in the next page.
P.16
RTA-8807
AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
P.16
WEIGHT LIMITS
110 Lbs. (49.89 Kg)
35 Lbs. (15.87 Kg)
55 Lbs. (24.95 Kg)
35 Lbs. (15.87 Kg)
35 Lbs. (15.87 Kg)
30 Lbs. (13.60 Kg)
30 Lbs. (13.60 Kg)
• Do not exceed the indicated weight limits.
• Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
• Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
• Do not use solvents or abrasive materials to clean the unit.
• If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
• Do not seat or stand on the unit.
• Do not allow small children to play over the unit, or inside the left compartment.
• Do not allow small children to reach inside the drawers or any compartment without your supervision.
• The unit must be handled by at least 2 persons when moving in the same or adjacent rooms.
• Before moving the unit, make sure to remove any object that is heavy or might fall off.
• When lifting the unit, use both hands and bend your knees, not your backs.
• When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
• The glass is made of safety tempered glass. The safety feature is that when breakage occurs, the glass shatters into many tiny pieces minimizing the risk of serious injuries. If the glass breaks, do not handle the pieces with your bare hands, take some pictures and contact Customer Service immediately. Please refer to the Contact Us card.
• Shall any part of the unit become defective during the warranty period, replacement parts might be available to you at no charge. Please refer to the WARRANTY card included with the product.
• The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.
• The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
Dependencies or other countries, please contact the supplier from where the unit was purchased.

Public link updated
The public link to your chat has been updated.
Advertisement