Untitled
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under
international copyright laws, with all rights reserved. Neither this manual, nor any of the
material contained herein, may be reproduced without written consent of the author.
Version 3.1
Disclaimer
The information in this document is subject to change without notice. The manufacturer
makes no representations or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for any particular purpose.
The manufacturer reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.
Other product names used in this manual are the properties of their respective owners and
are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment onto an outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with this
equipment to ensure compliance with the pertinent RF emission limits governing this
device. Changes or modifications not expressly approved by the system’s manufacturer
could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following
conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received, including interference
that may cause undesired operation
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference-causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le
matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Describes features of the motherboard.
Introducing the Motherboard
Go to
H
page 1
Describes installation of motherboard
components.
Chapter 2
Installing the Motherboard
Go to
H
page 7
Provides information on using the BIOS
Setup Utility.
Chapter 3
Using BIOS
Go to
H
page 25
Chapter 4
Describes the motherboard software
Using the Motherboard Software
Go to
Preface
H
page 37
iii
TABLE OF CONTENTS
Preface
i
Chapter 1
1
Introducing the Motherboard
1
Introduction.................................................................................................1
Feature..........................................................................................................2
Motherboard Components........................................................................4
Chapter 2
7
Installing the Motherboard
7
Safety Precautions......................................................................................7
Choosing a Computer Case.......................................................................7
Installing the Motherboard in a Case......................................................7
Checking Jumper Settings.........................................................................8
Setting Jumpers..............................................................................8
Checking Jumper Settings..............................................................9
Jumper Settings..............................................................................9
Connecting Case Components...............................................................10
Front Panel Header.....................................................................12
Installing Hardware...................................................................................13
Installing the Processor...............................................................14
Installing Memory Modules.........................................................15
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........17
Installing a Floppy Diskette Drive...............................................18
Installing Add-on Cards..............................................................19
Connecting Optional Devices......................................................21
Connecting I/O Devices..........................................................................23
Chapter 3
25
Using BIOS
25
About the Setup Utility............................................................................25
The Standard Configuration........................................................25
Entering the Setup Utility..............................................................25
Updating the BIOS.......................................................................27
Using BIOS................................................................................................27
Standard CMOS Setup.................................................................28
Features Setup.............................................................................30
iv
Power Management Setup...........................................................31
PCI/Plug and Play Setup.............................................................32
BIOS Security Features................................................................33
CPU PnP Setup............................................................................34
Hardware Monitor.......................................................................35
Load Best Performance Settings..................................................36
Load Optimal Defaults................................................................36
Save Changes and Exit................................................................36
Discard Changes and Exit...........................................................36
37
Chapter 4
Using the Motherboard Software
37
About the Software CD-ROM................................................................37
Auto-installing under Windows 2000/XP.............................................37
Running Setup..............................................................................38
Manual Installation..................................................................................40
Utility Software Reference.......................................................................40
Multi-Language Translation
1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the 915PL-A2 motherboard. This motherboard is a high performance, enhanced function motherboard that supports LGA775 Socket for latest Intel
Pentium 4/Celeron Processors.
The motherboard incorporates the 915PL Northbridge (NB) and ICH6 Southbridge (SB)
chipsets. The Northbridge on this motherboard supports a Front Side Bus (FSB) frequency
of 800/533 MHz using a scalable FSB Vcc_CPU. The momory controller supports DDR
memory DIMM frequencies of 333MHz and 400 MHz. It supports two DDR Sockets with
up to maximum memory of 2 GB. DDR Maximum memory bandwidth of 3.2 GB/s in singlechannel is supported, or 6.4 GB/s in dual-channel interleaved mode assuming DDR 400MHz.
High resolution graphics via two PCI Express slots, intended for Graphics Interface, are
fully compliant to the PCI Express Base Specification revision 1.0a.
The ICH6 Southbridge supports three PCI slots which are PCI 2.3 compliant. In addition,
one PCI Express x1 slot is supported, fully compliant to the PCI Express Base Specification, Revision 1.0a. It implements an EHCI compliant interface that provides 480Mb/s
bandwidth for eight USB 2.0 ports, integrates Azalia codec supporting Azilia standard that
features an 8-channel High Definition Audio output. One onboard IDE connector supports
2 IDE devices in ATA-100/66 mode. The Southbridge integrates a Serial ATA host controller
that is SATA v1.0 compliant, supporting four SATA ports with maximum transfer rate up to
150 MB/s each and LAN controller supporting 10/100Mbit/s ethernet.
The 915PL-A2 motherboard is equipped with advanced full set of I/O ports in the rear
panel, including PS/2 mouse and keyboard connectors, COM1, LPT1, four USB ports, one
optional LAN port, and audio jacks for microphone, line-in and 8-ch line out.
Introducing the Motherboard
2
Feature
Processor
The 915PL-A2 uses an LGA775 type of Pentium 4 that carries the following features:
•
•
•
Accommodates Intel P4/Celeron processors
Supports a system bus (FSB) of 800/533MHz
Supports “Hyper-Threading” technology CPU
“Hyper-Threading” technology enables the operating system into thinking it’s hooked
up to two processors, allowing two threads to be run in parallel, both on separate
“logical” processors within the same physical processor.
Chipset
The 915PL Northbridge (NB) and ICH6 Southbridge (SB) chipsets are based on an
innovative and scalable architecture with proven reliability and performance.
915PL (NB)
•
Supports 32-bit host bus addressing, allowing the CPU to
access the entire 4 GB of the memory address space.
•
Has a 12-deep In-Order Queue to support up to twelve
outstanding piplined address requests on the host bus.
•
Supports one PCI Express x16 for Graphics Interface, fully
compliant to the PCI Express base Sepcification revision
1.0a
•
Supports 256-Mb, 512-Mb and 1-Gb DDR technologies for
x8 and x16 devices
915PL chipset can only support 256-Mb, 512-Mb and 1-Gb DDR technologies
for x8 and x16 device, NOT support 128-Mb DDR technology. That is, 256 MB
Double Side Memory Module & 128 MB Single Side Memory Module are NOT
support.
ICH6 (SB)
•
•
•
•
•
•
•
•
Enhanced DMA Controller, interrupt controller, and timer functions
Compliant with PCI Express Base Specification, Revision
1.0a
Compliant with PCI 2.3 specificaiton
Compliant with Serial ATA 1.0a specification
Integrated USB 2.0 Host Controller supporting up to eight
USB 2.0 ports
Integrated LAN controller
Compliant with Azalia specification supporting 8 channels
of audio outputs
Integrated IDE controller supports Ultra ATA100/66/33
Memory
•
•
•
Supports DDR 400/333 MHz DDR SDRAM DIMMs
Accommodates two unbuffered DIMMs
Up to 1 GB per DIMM with maximum memory size up to 2 GB
Introducing the Motherboard
3
Onboard LAN (Optional)
The onboard LAN controller provides the following features:
•
•
•
•
Supports 100/10 Mb/s N-Way Auto negotiation operation
Compliant to PCI Revision 2.2
Supports Full Duplex Flow Control (IEEE 802.3x)
2.5/3.3V power supply with 5V tolerant I/Os
Audio
•
•
•
•
Compliant with AC’97 2.3 specification
Meets performance requirements for audio on PC99/2001 systems
8 Channels DA Converters with 48KHz rate
Meets Microsoft SHQL/WLP 2.0 audio requirements
Expansion Options
The motherboard comes with the following expansion options:
•
•
•
•
•
•
Two PCI Express x16 slots for Graphic Interface
One PCI Express x1 slot
Three 32-bit PCI v2.3 compliant slots
One 40-pin IDE low profile connector that support two IDE devices
One floppy disk drive connector
Four 7-pin SATA connectors
The 915PL-A2 motherboard supports UltraDMA bus mastering with transfer rates of
100/66 MB/s.
Integrated I/O
The
•
•
•
•
•
•
motherboard has a full set of I/O ports and connectors:
Two PS/2 ports for mouse and keyboard
One serial port
One parallel port
Four USB ports
One LAN port (optional)
Audio jacks for microphone in, line-in and 8-ch High Definition Audio output
BIOS Firmware
This motherboard uses AMI BIOS that enables users to configure many system
features including the following:
•
•
•
•
Power management
Wake-up alarms
CPU parameters
CPU and memroy timing
The firmware can also be used to set parameters for different processor clock speeds.
Some hardware specifications and software items are subject to change
with out prior notice.
Introducing the Motherboard
4
Motherboard Components
Introducing the Motherboard
5
Table of Motherboard Components
LABEL
1 CPU Socket
2 CPUFAN1
3 DIMM1/3
4 FDD1
5 ATX1
6 IDE1
7 SATA1~4
8 PANEL1
9 SPK1
10 CASFAN1
11 CLR_CMOS1
12 USB3-4
13 ATX4P1
14 AUDIO1
15 SPDIFO1
16 PCI1~3
17 CDIN1
COMPONENT
LGA775 socket for Pentium 4 CPUs
CPU cooling fan connector
184-pin DDR SDRAM slots
Floppy diskette drive connector
Standard 24-pin ATX power connector
Primary IDE channel
Serial ATA connectors
Panel connector for case switches and LEDs
Speaker header
Case cooling fan connector
Clear CMOS jumper
Front Panel USB headers
Auxiliary power connector for graphics interface
Front panel audio header
SPDIF out header
32-bit add-on card slots
CD-in header
18 PCI-E1/E3
PCI Express x16 slots
19 PCI-E2
20 PWRFAN1
21 PWR1
PCI Express x1 slot
Power cooling fan connector
Auxiliary 4-pin power connector
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Introducing the Motherboard
6
Memo
Introducing the Motherboard
7
Chapter 2
Installing the Motherboard
Safety Precautions
•
•
•
•
•
Follow these safety precautions when installing the motherboard
Wear a grounding strap attached to a grounded device to avoid damage from
static electricity
Discharge static electricity by touching the metal case of a safely grounded
object before working on the motherboard
Leave components in the static-proof bags they came in
Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies with
the specifications for the ATX system case. First, some features on the motherboard are
implemented by cabling connectors on the motherboard to indicators and switches on the
system case. Make sure that your case supports all the features required. Secondly, 915PLA2 supports one or two floppy diskette drives and two enhanced IDE drives. Make sure that
your case has sufficient power and space for all drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the motherboard.
This motherboard carries an ATX form factor of 305 x 244 mm. Choose a case that
accommodates this form factor.
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in a case.
Most system cases have mounting brackets installed in the case, which correspond the holes
in the motherboard. Place the motherboard over the mounting brackets and secure the
motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion slots
on your motherboard.
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than
one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on
the correct pins.
The illustrations show a 2-pin jumper. When
the jumper cap is placed on both pins, the
jumper is SHORT. If you remove the jumper
cap, or place the jumper cap on just one pin,
the jumper is OPEN.
SHORT
This illustration shows a 3-pin jumper. Pins
1 and 2 are SHORT
Installing the Motherboard
OPEN
9
Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
Jumper Settings
Jumper
Type
CLR_CMOS1 3-pin
Description
CMOS
Setting
1-2: NORMAL
CLR_CMOS1
2-3: CLEAR CMOS
Before clearing the
CMOS, make sure to
turn off the system.
Installing the Motherboard
1
10
Connecting Case Components
After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:
1
2
3
4
5
6
7
8
Connect the CPU cooling fan cable to CPUFAN1.
Connect the case cooling fan connector to CASFAN1.
Connect the power cooling fan connector PWRFAN1
Connect the case speaker cable to SPK1.
Connect the connector for graphics interface to ATX4P1
Connect the case switches and indicator LEDs to the PANEL1.
Connect the standard power supply connector to ATX1.
Connect the auxiliary case power supply connector to PWR1.
Connecting 20/24-pin power cable
Users please note that the 20-pin and 24-pin power cables can both be connected to the ATX1 connector. With the 20-pin power cable, just align the 20pin power cable with the pin 1 of the ATX1 connector. However, using 20-pin
power cable may cause the system to become unbootable or unstable because of
insufficient electricity.
20-pin power cable
With ATX v1.x power supply, users please
note that when installing 20-pin power cable,
the latche of power cable falls on the left
side of the ATX1 connector latch, just as the
picture shows.
With ATX v2.x power supply, users please
note that when installing 24-pin power cable,
the latches of power cable and the ATX1
match perfectly.
24-pin power cable
Installing the Motherboard
11
CPUFAN1: CPU Cooling FAN Power Connector
Pin
Signal Name
Function
1
2
3
GND
Sense
System Ground
Power +12V
Sensor
4
PWM
CPU FAN control
+12V
Users please note that the fan connector supports the CPU cooling
fan of 1.1A~2.2A (26.4W max.) at +12V.
CASFAN1/PWRFAN1: System Cooling FAN Power Connectors
Pin
1
2
3
Signal Name
Function
System Ground
Power +12V
Sensor
GND
+12V
Sense
ATX1: ATX 24-pin Power Connector
Pin
Signal Name
1
2
3
4
5
6
7
8
9
+3.3V
10
11
12
+12V
Pin
13
14
15
16
17
18
19
20
21
+3.3V
Ground
+5V
Ground
+5V
Ground
PWRGD
+5VSB
22
23
24
+12V
+3.3V
Signal Name
+3.3V
-12V
COM
PS_ON
COM
COM
COM
-5V
+5V
+5V
+5V
COM
PWR1: ATX 12V Power Connector
Pin
1
2
3
4
Signal Name
Ground
Ground
+12V
+12V
SPK1: Internal speaker
Pin
1
2
3
4
Signal Name
VCC
Key
Ground
Signal
Installing the Motherboard
12
ATX4P1: Auxliary Power Connector for Graphics Interface
Pin
Signal Name
1
2
3
4
NC
Make sure to connect a 4-pin ATX power cable
to ATX4P1; otherwise, the system will be unstable.
GND
GND
+12V
Front Panel Header
The front panel header (PANEL1) provides a standard set of switch and LED connectors
commonly found on ATX or Micro ATX cases. Refer to the table below for information:
Pin
1
Signal
Function
Pin
Signal
Function
HD_LED_P Hard disk LED+
2
FP PWR/SLP *MSG LED+
3
HD_LED_N Hard disk LED-
4
FP PWR/SLP *MSG LED-
5
RST_SW_N Reset Switch
6
PWR_SW_P Power Switch
7
RST_SW_P
Reset Switch
8
PWR_SW_N Power Switch
9
RSVD
Reserved
10 Key
No pin
* MSG LED (dual color or single color)
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data
is being read from or written to the hard drive. For the LED to function properly, an IDE
drive should be connected to the onboard IDE interface. The LED will also show activity
for devices connected to the SCSI (hard drive activity LED) connector.
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power
on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact
switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momentarycontact switch that is normally open. The switch should maintain contact for at least 50 ms
to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry. After receiving a power on/off signal, at least two seconds elapses before
the power supply recognizes another on/off signal.
Installing the Motherboard
13
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the motherboard or any of the surface-mount
resistors with the clip of the cooling fan. If the clip of the cooling fan
scrapes across the motherboard, you may cause serious damage to the
motherboard or its components.
On most motherboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.
Avoid using cooling fans with sharp edges on the fan casing and the clips.
Also, install the cooling fan in a well-lit work area so that you can clearly
see the motherboard and processor socket.
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system bus
frequency for the processor. You may be able to change these settings by making changes
to jumpers on the motherboard, or changing the settings in the system Setup Utility. We
strongly recommend that you do not over-clock processors or other components to run
faster than their rated speed.
Warning: Over-clocking components can adversely affect the reliability
of the system and introduce errors into your system. Over-clocking can
permanently damage the motherboard by generating excess heat in
components that are run beyond the rated limits.
This motherboard has a LGA 775 socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock
speed and system bus frequency of the processor, and the quantity of internal cache memory
and external cache memory.
Installing the Motherboard
14
CPU Installation Procedure
The following illustration shows CPU installation components.
A. Unload the cap
· Use thumb & forefinger to hold the
lifting tab of the cap.
· Lift the cap up and remove the cap
completely from the socket.
B. Open the load plate
· Use thumb & forefinger to hold the
hook of the lever, pushing down and pulling
aside unlock it.
· Lift up the lever.
· Use thumb to open the load plate. Be
careful not to touch the contacts.
C. Install the CPU on the socket
· Orientate CPU package to the socket.
Make sure you match triangle marker
to pin 1 location.
D. Close the load plate
· Slightly push down the load plate onto the
tongue side, and hook the lever.
· CPU is locked completely.
E. Apply thermal grease on top of the CPU.
F.
Fasten the cooling fan supporting base onto
the CPU socket on the motherboard.
G. Make sure the CPU fan is plugged to the
CPU fan connector. Please refer to the CPU
cooling fan user’s manual for more detail
installation procedure.
To achieve better airflow rates and heat dissipation, we suggest that you use
a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The
form and size of fan/heatsink may also vary.
Installing the Motherboard
15
Installing Memory Modules
This motherboard accommodates two memory modules. It can support two 184-pin 2.5V
unbuffered DIMM, DDR400/333/266. The total memory capacity is 2GB.
DDR SDRAM memory module table
Memory module
DDR266
DDR333
DDR400
Memory Bus
133MHz
166MHz
200MHz
You must install at least one module in any of the three slots. Each module can be installed
with 128 MB to 1 GB of memory; total memory capacity is 2GB.
Do not remove any memory module from its antistatic packaging until you
are ready to install it on the motherboard. Handle the modules only by
their edges. Do not touch the components or metal parts. Always wear a
grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules.
1
2
3
4
5
6
This motherboard supports unbuffered DDR SDRAM .
Push the latches on each side of the DIMM slot down.
Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
Check that the cutouts on the DIMM module edge connector match the notches
in the DIMM slot.
Install the DIMM module into the slot and press it firmly down until it seats
correctly. The slot latches are levered upwards and latch on to the edges of
the DIMM.
Install any remaining DIMM modules.
Installing the Motherboard
16
Table A: DDR (memory module) QVL (Qualified Vendor List)
The following DDR400 memory modules have been tested and qualified for use with this
motherboard.
Size
256MB
512MB
1GB
Vendor
SAMSUNG
SAMSUNG
TwinMOS
KingMax
W inbond
A-DATA
A-DATA
Kingston
Kingston
Hynix
Hynix
GEIL
GEIL
Ram axel
Apacer
SAMSUNG
SAMSUNG
Infineon
Elixir
Kingston
Kingston
PSC
Hynix
Transcend
CORSAIR
CORSAIR
CORSAIR
Mushkin
UNIFOSA
GEIL
G.SKILL
AEN EON
AEN EON
CORSAIR
M odel N am e
K4H560838D-TCC4
K4H 560838D-TCCC
T MD7608F8E50D
KD L388P4EA-50A
W 942508BH-5
ADD8608A8A-5B
AD D8608A8A-4.5B
D3208DL2T-5 0323PT 01
9905192-012.A01
HY5D U5656822BT-D 43
HY5DU56822BT-D43
GE08L3264D1W L5NKT3H71
G208L364D1T G5NKT 3C
MT-46V32M 8 TG-5BC
AM3A568ACT-5A
K4H560838D-TCC4
K4H560838E-TCCC
HYB25D256800BT-5
N2DS25680BT-5T
D3208D L1T-5
KHX3500AK2
A2S56D30BTP
HY5DU56822DT-D5
V58C2256804SAT5B
CM X512-3200C2PT
CM X512-3500C2PT
C MX512-4400PT
PC 3500 level ONE
USI 64M8B8-W B200-0431
G E1GB3200BDC
F1-3200PHU 2-1 GVZX
AED93T 500
AED83T 500
CM X1024-3200PT
Installing the Motherboard
17
Installing a Hard Dish Drive/CD-ROM/SATA Hard Drive
This section describes how to install IDE devices such as a hard disk drive and a CD-ROM
drive.
About IDE Devices
Your motherboard has one IDE channel interface. An IDE ribbon cable supporting two IDE
devices is bundled with the motherboard.
You must orient the cable connector so that the pin1 (color) edge of the
cable correspoinds to the pin 1 of the I/O port connector.
IDE1: IDE Connector
This motherboard supports four high data transfer SATA ports with each runs up to 150
MB/s. To get better system performance, we recommend users connect the CD-ROM to
the IDE channel, and set up the hard dives on the SATA ports.
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE.
Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that
one device is set to MASTER and the other device is set to SLAVE. The documentation of
your IDE device explains how to do this.
About SATA Connectors
Your motherboard features four SATA connectors supporting a total of four drives. SATA ,
or Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE
hard drives which are currently used in most PCs. These connectors are well designed and
will only fit in one orientation. Locate the SATA connectors on the motherboard and follow
the illustration below to install the SATA hard drives.
Installing Serial ATA Hard Drives
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial
ATA protocol. This SATA cable comes with an SATA power cable. You can connect either
end of the SATA cable to the SATA hard drive or the connector on the motherboard.
SATA cable
(optional)
SATA power cable
Installing the Motherboard
(optional)
18
Refer to
1
2
3
the illustration below for proper installation:
Attach either cable end to the connector on the motherboard.
Attach the other cable end to the SATA hard drive.
Attach the SATA power cable to the SATA hard drive and connect the other
end to the power supply.
This motherboard does not support the “Hot-Plug” function.
Installing a Floppy Diskette Drive
The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive
ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch
drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one
type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.
You must orient the cable connector so that the pin 1 (color) edge of the
cable corresponds to the pin 1 of the I/O port connector.
FDD1: Floppy Disk Connector
This connector supports the provided floppy drive ribbon cable. After connecting the single
end to the onboard floppy connector, connect the remaining plugs on the other end to the
floppy drives correspondingly.
Installing the Motherboard
19
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the
system bus. Expansion slots are a means of adding or enhancing the motherboard’s features
and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
PCI-E1
Slot
The PCI Express slot is used to install an external PCI Express graphics card
that is fully compliant to the PCI Express Base Specification revision 1.0a.
PCI-E2
Slot
The PCI Express x1 slots is fully compliant to the PCI Express Base Specification revision 1.0a as well.
PCI-E3
Slot
The PCI Express slot is used to install an external PCI Express graphics card
that is fully compliant to the PCI Express Base Specification revision 1.0a.
PCI 1~3
Slots
This motherboard is equipped with three standard PCI slots. PCI stands for
Peripheral Component Interconnect and is a bus standard for expansion
cards, which for the most part, is a supplement of the older ISA bus standard.
The PCI slots on this board are PCI v2.3 compliant.
1. Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually
configure the card before installation.
2. PCI-E1 slot will be disabled when PCIEX2 slot is installed.
Installing the Motherboard
20
Follow these instructions to install add-on cards:
1.
2.
3.
4.
5.
6.
Open the chassis and then remove the slot bracket from the case where you will
be installing the expansion cards.
Install your graphics card in the proper slot by pressing the card firmly into the
slot.
Drive in the screw to secure the slot bracket of the expanson card.
Replace your computer’s chassis cover.
Power on the computer, if necessary, set up BIOS utility of expansion card from
BIOS.
Install related driver to complete the installation.
Installing two graphics cards
Notes: 1. The two PCIE x16 slots run in two modes. With only one PCI Express
Graphics card, install it onto PCI-E1 slot by default. Having two PCI
Express Graphics cards at hand, set them up onto PCI-E1 and PCI-E3
slots simultaneously.
2. The Scalable D.G.E. supports a four-monitor configuration when PCIE x16
slot and PCIEx4 slot are working simultaneously.
3. Please note that the graphics card driver supports Windows 2000/XP only.
4. Make sure to connect a 4-pin ATX power cable to the ATX4P1; otherwise,
the system will be unstable.
Installing the Motherboard
21
Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional devices:
AUDIO1: Front Panel Audio header
This header allows the user to install auxiliary front-oriented microphone and line-out ports
for easier access.
Pin
Signal Name
Function
1
2
3
4
5
6
7
AUD_MIC
Front Panel Microphone input signal
AUD_GND
Ground used by Analog Audio Circuits
8
9
10
Key
No Pin
AUD_F_L
Left Channel Audio signal to Front Panel
REVD
Reserved
AUD_MIC_BIAS Microphone Power
AUD_VCC
Filtered +5V used by Analog Audio Circuits
AUD_F_R
Right Channel audio signal to Front Panel
REVD
Reserved
REVD
Reserved
CDIN1: CD Audio Input header
Pin
1
2
3
4
Signal Name
CD in_L
GND
GND
CD in_R
Function
CD In left channel
Ground
Ground
CD In right channel
Installing the Motherboard
22
USB3~4: Front Panel USB header
The motherboard has four USB ports installed on the rear edge I/O port array. Additionally,
some computer cases have USB ports at the front of the case. If you have this kind of case,
use auxiliary USB connector to connect the front-mounted ports to the motherboard.
Pin
Signal Name
Function
1
2
3
4
5
6
7
USBPWR
Front Panel USB Power
USBPWR
Front Panel USB Power
USB_FP_P0-
USB Port 0 Negative Signal
USB_FP_P1-
USB Port 1 Negative Signal
USB_FP_P0+
USB Port 0 Positive Signal
USB_FP_P1+
USB Port 1 Positive Signal
GND
Ground
8
9
10
GND
Ground
Key
No pin
NC
Not connected
SATA1/2/3/4: Serial ATA connectors
These connectors are use to support the new Serial ATA devices for the highest date transfer
rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations
of the current Parallel ATA interface. But maintains register compatibility and software
compatibility with Parallel ATA.
Pin
Pin
Pin
1
3
5
7
Signal
Name
Signal
Name
Signal Name
Ground
TXRXGround
Pin
Signal Name
Function
TX+
2
4
6
-
Ground
RX+
-
SPDIF01: SPDIF out header (optional)
This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output
to digital multimedia device through optical fiber or coxial connector.
Pin
Pin
Signal Name
Name
1 Signal
SPDIF
2
+5VA
3
Key
4
GND
Function
Installing the Motherboard
23
Connecting I/O Devices
The backplane of the motherboard has the following I/O ports:
PS2 Mouse
Use the upper PS/2 port to connect a PS/2 pointing device.
PS2 Keyboard
Use the lower PS/2 port to connect a PS/2 keyboard.
Parallel Port (LPT1) Use LPT1 to connect printers or other parallel communications
devices.
Serial Port
(COM1)
Use the COM port to connect serial devices such as mice or
fax/modems. COM1 is identified by the system as COM1/3.
LAN Port
Connect an RJ-45 jack to the LAN port to connect your computer
to the Network.
(optional)
USB Ports
Use the USB ports to connect USB devices.
Audio Ports
Use the audio jacks to connect audio devices. The A port is for
stereo line-in signal, while the C port is for microphone in signal.
This motherboard supports 8-channel audio devices that correspond to the A, B, D, and E port respectively. In addition, all of the
3 ports, A, B, and D provide users with both right & left channels
individually. Users please refer to the following note for specific
port function definition.
A: Line-in/Side Surround
B: Front Out
C: Microphone In
D: Back Surround
E: Center/Bass
F: Optical S/PDIF Out
The above port definition of A,B,C,D, and E can be changed to
audio input or audio output by changing the driver utility setting.
This concludes Chapter 2. The next chapter covers the BIOS.
Installing the Motherboard
24
Memo
Installing the Motherboard
25
Chapter 3
Using BIOS
About the Setup Utility
The computer uses the latest American Megatrends BIOS with support for Windows Plug
and Play. The CMOS chip on the motherboard contains the ROM setup instructions for
configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are
stored in battery-backed-up CMOS RAM that saves this information when the power is
turned off. When the system is turned back on, the system is configured with the values you
stored in CMOS.
The BIOS Setup Utility enables you to configure:
•
Hard drives, diskette drives and peripherals
•
Video display type and display options
•
Password protection from unauthorized use
•
Power Management features
The settings made in the Setup Utility affect how the computer performs. Before using the
Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we recommend
that you read this chapter in case you need to make any changes in the future.
This Setup Utility should be used:
•
when changing the system configuration
•
when a configuration error is detected and you are prompted to make changes
to the Setup Utility
•
when trying to resolve IRQ conflicts
•
when making changes to the Power Management configuration
•
when changing the password or making other changes to the Security Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines.
POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are
completed, the following message appears:
Using BIOS
26
Press DEL/F1 to enter SETUP
Press the delete key or F1 to access the BIOS Setup Utility.
CMOS Setup Utility -- Copyright (C) 1985-2004, American Megatrends, Inc.
f Standard CMOS Setup
f Advanced Setup
f Features Setup
f Power Management Setup
f PCI / Plug and Play Setup
f BIOS Security Features
fCPU PnP Setup
f Hardware monitor
Load Best Performance settings
Load Optimal Defaults
Save Changes and Exit
Discard Changes and Exit
mnkl
: Move +/-/: Value Enter : Select F1: General Help ESC: Exit
F10: Save
F8:Best Performance Settings
F9: Optimized Defaults
Standard CMOS setup for changing time, date, hard disk type, etc.
v02.56 (C)Copyright 1985-2004, American Mega trends, Inc.
BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY
ESC
oqrt
+/-/PU/PD
F1
FUNCTION
Exits the current menu
Scrolls through the items on a menu
Modifies the selected field’s values
Displays a screen that describes all key functions
F8
Loads the best setting for peak performance
F9
Loads an optimized setting for better performance
F10
ESC
Saves the current configuration and exits setup
Exits the current menu
Using BIOS
27
Updating the BIOS
You can download and install updated BIOS for this motherboard from the manufacturer’s
Web site. New BIOS provides support for new peripherals, improvements in performance,
or fixes for known bugs. Install new BIOS as follows:
1
If your motherboard has a BIOS protection jumper, change the setting to allow
BIOS flashing.
2
If your motherboard has an item called Firmware Write Protect in Advanced
BIOS features, disable it. (Firmware Write Protect prevents BIOS from being
overwritten.
3
Create a bootable system disk. (Refer to Windows online help for information
on creating a bootable system disk.)
4
Download the Flash Utility and new BIOS file from the manufacturer’s Web
site. Copy these files to the system diskette you created in Step 3.
5
Turn off your computer and insert the system diskette in your computer’s
diskette drive. (You might need to run the Setup Utility and change the boot
priority items on the Advanced BIOS Features Setup page, to force your
computer to boot from the floppy diskette drive first.)
6
At the A:\ prompt, type the Flash Utility program name and the filename of the
new bios and then press <Enter>. Example: AMINF340.EXE 040706.ROM
7
When the installation is complete, remove the floppy diskette from the diskette
drive and restart your computer. If your motherboard has a Flash BIOS jumper,
reset the jumper to protect the newly installed BIOS from being overwritten.
The computer will restart automatically.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup
Utility displays a list of the options that are available. A highlight indicates which option is
currently selected. Use the cursor arrow keys to move the highlight to other options. When
an option is highlighted, execute the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to
execute that option. Other options lead to dialog boxes that prompt you for information.
Some options (marked with a triangle f ) lead to submenus that enable you to change the
values for the option. Use the cursor arrow keys to scroll through the items in the submenu.
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a
triangle f .
Using BIOS
28
Standard CMOS Setup
This option displays basic information about your system.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
Standard CMOS Setup
System Time
System Date
14: 02: 44
Wed 05/05/2004
Primary IDE Master
f Primary
IDE Slave
f Secondary
IDE Master
f Secondary IDE
Slave
f
f Third IDE Master
f Third IDE Slave
Not Detected
Not Detected
Not Detected
Not Detected
Not Detected
Not Detected
Floppy A
1.44 MB 31/2”
Help Menu
Use [ENTER], [TAB]
or [SHIFT-TAB] TO
select a field.
Use [+] or [-] to
configure system Time.
mnkl
: Move +/-/: Value Enter : Select F1: General help
ESC: Exit
F10: Save
F8:Best Performance Settings
F9: Optimized Defaults
Date and Time
The Date and Time items show the current date and time on the computer. If
you are running a Windows OS, these items are automatically updated whenever you make
changes to the Windows Date and Time Properties utility.
f Primary/Secondary/Third IDE Master/Slave
Your computer has one IDE channel and each channel can be installed with one or two
devices (Master and Slave). In addition, this motherboard supports four SATA channels and
each channel allows one SATA device to be installed. Use these items to configure each
device on the IDE channel.
Floppy A
These items set up size and capacity of the floppy diskette drive(s) installed in the
system.
Press <Esc> to return to the main menu setting page.
Advanced Setup
This page sets up more advanced information about your system. Handle this page with
caution. Any changes can affect the operation of your computer.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
Advanced Setup
Quick Boot
1st Boot Device
2nd Boot Device
3rd Boot Device
Try Other Boot Device
Bootup num-Luck
Configure DRAM timing by SPD
Hyper Threading Tecnnology
Max CPUID Value Limit
Excute Disable Bit
CPU TM Function
C1E Support
Auto Detect DIMM/PCI Clk
Spread Spectrum
Aperture Size Select
Enabled
HDD:SS-ST3120026AS
CD/DVD:3M-Pioneer D
1st Floppy Drive
Yes
On
Enabled
Enabled
Disabled
Disabled
TM2
Disabled
Enabled
Disabled
128MB
mnkl : Move
Help Menu
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
+/-/: Value Enter : Select F1: General help ESC: Exit
F8:Best Performance Settings F9: Optimized Defaults
F10: Save
Using BIOS
29
Quick Boot (Enabled)
If you enable this item, the system starts up more quickly because of the elimination of
some of the power on test rutines.
1st/2nd/3rd Boot Device
Use this item to determine the device order the computer used to look for an operating
system to load at start-up time. The devices showed here will be different depending on the
exact devices installed on your motherboard.
Try Other Boot Device (Yes)
If you enable this item, the system will also search for other boot devices if it fails to find
an operating system from the first boot device.
BootUp Num-Lock (On)
This item determines if the Num Lock key is active or inactive at system start-up time.
Configure DRAM Timing by (Enabled)
This item allows you to enable or disable the DRAM timing defined by the Serial Presence
Detect electrical.
Hyper Threading Technology (Enabled)
You can set “Disabled” or “Enabled” to control HT CPU support in O.S. Set “Enabled” to
test HT CPU function.
Max CPUID Value Limit (Disabled)
Enable this item when users intend to install NT4.0 to make the system work properly with
Prescott and LGA775 CPU.
Excute Disable Bit (Disabled)
This item is a security feature that helps you protect your CPU and operating system
against malicious software executing code. This item is available when CPU supports the
feature and it is an optional item.
CPU TM Function (TM2)
This item displays CPU’s temperature and enhances you to set a safe temperature for CPU.
C1E Support (Disabled)
Use this item to descrease the bus ratio that reduces the consumption of CPU electricity and
power.
Auto Detect DIMM/PCI Clk (Enabled)
When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.
Spread Spectrum (Disabled)
If you enable spread spertrum, it can significantly reduce the EMI (Electro-Magnetic
interface) generated by the system.
Aperture Size Select (128MB)
This item defines the size of the aperture if you use an AGP graphics adapter. The AGP
aperture refers to a section of the PCI memory address range used for graphics memory. We
recommend that you leave this item at the default value.
Press <Esc> to return to the main menu setting page.
Using BIOS
30
Features Setup
This page sets up some parameters for peripheral devices connected to the system.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
Features Setup
OnBoard Floppy Controller
Serial Port1 Address
Parallel Port Address
Parallel Port Mode
ECP Mode DMA Channel
Parallel Port IRQ
OnBoard PCI IDE Controller
ATA/IDE Configuration
Ethernet Device
Audio Device
Onboard USB Function
USB Function For DOS
Enabled
3F8/IRQ4
378
ECP
DMA3
IRQ7
Both
Enhanced
Enabled
Enabled
Enabled
Disabled
Help Menu
Allow BIOS to Enable or
Disable Floppy Controller.
mnkl
: Move +/-/: Value Enter : Select F1: General help ESC: Exit
F8:Best Performance Settings
F9: Optimized Defaults
F10: Save
OnBoard Floppy Controller (Enabled)
Use this item to enable or disable the onboard floppy disk drive interface.
Serial Port1 Address (3F8/IRQ4)
Use this item to enable or disable the onboard COM1 serial port, and to assign a port address.
Parallel Port Address (378)
Use this item to enable or disable the onboard Parallel port, and to assign a port address.
Parallel Port Mode (ECP)
Use this item to select the parallel port mode. You can select Normal (Standard Parallel
Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or BPP (BiDirectional Parallel Port).
ECP Mode DMA Channel (DMA3)
Use this item to assign the DMA Channel under ECP Mode function.
Parallel Port IRQ (IRQ7)
Use this item to assign IRQ to the parallel port.
OnBoard PCI IDE Controller (Both)
Use this item to enable or disable either or both of the onboard Primary and Secondary IDE
channels.
ATA/IDE Configuration (Enhanced)
The ATA/IDE option can be configured as either “Enhanced (default)” or
“Compatible” in the BIOS configuration. Windows* 98SE and Windows* Me operating
systems do not support Enhanced mode IDE/Serial ATA resources for more than four
devices. If the ATA/IDE option is set to Enhanced mode, the operating installation will
not be able to recognize the drive, and the installation will fail. Before installing 98SE
or Me, the ATA/IDE configuration must be changed from Enhanced to Compatible
mode
Using BIOS
31
Ethernet Device (Enabled)
Use this item to enable or disable the onboard Ethernet.
Audio Device (Enabled)
Use this item to enable or disalbe the onboard audio device.
Onboard USB Function (Enabled)
Enable this item if you plan to use the USB ports on this motherboard.
USB Function For DOS (Disabled)
Enable this item if you plan to use the USB ports on this motherboard in a DOS environment.
Press <Esc> to return to the main menu setting page.
Power Mangement Setup
This page sets up some parameters for system power management operation.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
Power Management Setup
ACPI Aware O/S
Power Management
ACPI Enhanced Efficiency
Suspend Time Out
LAN/Ring Power On
Resume on RTC Alarm
Keyborad Power On
Password
Yes
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Press Enter
Help Menu
Yes / No
ACPI support for
Operating System.
YES: If OS
supports ACPI.
NO: If OS
does not support
ACPI.
mnkl
: Move +/-/: Value Enter : Select F1: General help ESC: Exit
F10: Save
F8:Best Performance Settings
F9: Optimized Defaults
ACPI Aware O/S (Yes)
This itme supports ACPI (Advanced Configuraion and Power Management Interface). Use
this item to enable or disable the ACPI feature.
Power Management (Enabled)
Use this item to enable or disable a power management scheme. If you enable power
management, you can use this item below to set the power management operation. Both
APM and ACPI are supported.
ACPI Enhanced Efficiency (Disabled)
This item allows you to enable or disable ACPI Enhanced Efficiency function.
Suspend Time Out (Disabled)
This item sets up the timeout for Suspend mode in minutes. If the time selected passes
without any system activity, the computer will enter power-saving Suspend mode.
LAN/Ring Power On (Disabled)
The system can be turned off with a software command. If you enable this item, the system
can automatically resume if there is an incoming call on the Modem/Ring, or traffic on the
network adapter. You must use an ATX power supply in order to use this feature.
Using BIOS
32
Resume on RTC Alarm (Disabled)
The system can be turned off with a software command. If you enable this item, the system
can automatically resume at a fixed time based on the system’s RTC (realtime clock). Use
the items below this one to set the date and time of the wake-up alarm. You must use an ATX
power supply in order to use this feature.
Keyboard Power On (Disabled)
If you enable this item, system can automatically resume by pressing any keys or power key
or typing in the password on the keyboard. You must use an ATX power supply in order to
usethis feature.
Password (Press Enter)
When Keyboard Power On is set to “Password”, this item is available and users can enter the
password.
Press <Esc> to return to the main menu setting page.
PCI / Plug and Play Setup
This page sets up some parameters for devices installed on the PCI bus and those utilizing
the system plug and play capability.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
PCI / Plug and Play Setup
Plug & Play Aware O/S
Primary Graphics Adapter
Allocate IRQ to PCI VGA
PCI IDE BusMaster
Yes
PCI-E VGA
Yes
Enabled
Help Menu
No: lets the BIOS
configure all the
devices in the system.
YES: lets the
operating system
configure Plug and
Play (PnP) devices not
required for boot if
your system has a Plug
and Play operating
system.
mnkl
: Move
+/-/: Value
Enter : Select F1: General help ESC: Exit
F8:Best Performance Settings F9: Optimized Defaults
F10: Save
Plug & Play Aware O/S (Yes)
This itme select which, the BIOS or the operating system, will configure all the devices in
the system. If set NO, the BIOS configures the system; set YES, the operating system
configure Plug and Play devices.
Primary Graphics Adapter (PCI-E VGA)
This itme indicates if the primary graphics adapter uses the PCI-E VGA, PCI VGA, or AGPE VGA.
Allocate IRQ to PCI VGA (Yes)
If this item is enabled, an IRQ will be assigned to the PCI VGA graphics system. You set this
value to No to free up an IRQ.
Using BIOS
33
PCI IDE BusMaster (Enabled)
This item enables or disabled the DMA under DOS mode. We recommend you to leave this
item at the default value.
Press <Esc> to return to the main menu setting page.
BIOS Security Features
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
BIOS Security Features
Security Settings
_____________________________________________________
Supervisor Password : Not Installed
Change Supervisor Password
Password Check
Press Enter
Setup
Help Menu
Install or Change the
password.
mnkl
: Move +/-/: Value Enter : Select F1: General help ESC: Exit
F10: Save
F8:Best Performance Settings
F9: Optimized Defaults
Supervisor Password (Not Installed)
This item indicates whether a supervisor password has been set. If the password has benn
installed, Installed displays. If not, Not Installed displays.
Change Supervisor Password (Press Enter)
You can select this option and press <Enter> to access the sub menu. You can use the sub
menu to change the supervisor password.
Password Check (Setup)
This item enables users to choose the time when the system will perform password check.
Press <Esc> to return to the main menu setting page.
Using BIOS
34
CPU PnP Setup
This page helps you manually configure the CPU of this motherborad. The system will
automatically detect the type of installed CPU and make the appropriate adjustments to
these items on this page.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
CPU PnP Setup
Manufacturer:
DRAM Frequency
CPU Frequency
CPU Over-clocking Func.
Memory Voltage
Intel
Auto
200MHz
Disabled
2.65V
Help Menu
This item should be enabled
order to boot legacy
OSes that cannot
support CPUs with
extended CPUID
functions.
mnkl
: Move +/-/: Value Enter : Select F1: General help
ESC: Exit
F10: Save
F8:Best Performance Settings
F9: Optimized Defaults
Manufacturer (Intel)
These items indicate the brand of the CPU installed in your system.
DRAM Frequency (Auto)
This item enables users to adjust the DRAM frequency. The default setting is auto and we
recommend users leave the setting unchanged. Modify it at will may cause the system to be
unstable.
CPU Frequency
This item indicates the current CPU frequency. Users can not make any change to this item.
Please noted that the frequency will be varied with different CPU.
CPU Over-clocking Func. (Disabled)
This item decides the CPU over-clocking function/frequencyinstalled in your system. If the
over-clocking fails, please turn offthe system power. And then, hold the PageUp key
(similar to theClear CMOS function) and turn on the power, the BIOS willrecover the safe
default.
Memory Voltage (2.65V)
This item allows you to adjust memory voltage.
Press <Esc> to return to the main menu setting page.
Using BIOS
35
Hardware Monitor
This page helps you set up some parameters for the hardware monitoring function of this
motherboard.
CMOS Setup Utility - Copyright (C) 1985-2004, American Megatrends, Inc.
Hardware Monitor
-=- System Hardware Monitor -=Vcore
VIvdd
VCC3V
CPU FAN Speed
Power FAN Speed
Chassis FAN Speed
CPU Temperature
System Temperature
Help Menu
:
:
:
:
:
:
:
:
1.324 V
1.467 V
3.241 V
2463 RPM
0 RPM
0 RPM
47oC/116oF
45oC/113oF
Enables hardware
health monitoring
Device.
mnkl : Move
+/-/: Value Enter : Select F1: General help
ESC: Exit
F10: Save
F8:Best Performance Settings
F9: Optimized Defaults
System Hardware Monitor
These items display the monitoring of the overall inboard hardware health events, such as
CPU temperature, system temperature, system fan,...etc.
Press <Esc> to return to the main menu setting page.
Using BIOS
36
Load Best Performance Settings
If you select this item and press Enter a dialog box appears. If you select [OK], and
then Enter, the Setup Utility loads a set of best-performance default values. These
default are quite demanding and your system might not function properly if you are
using slower memory chips or other low-performance components.
Warning: To load Best Performance Settings may make your system unstable
or unbootable.
Load Optimal Defaults
This option opens a dialog box that lets you install optimized defaults for all appropriate
items in the Setup Utility. Press <OK> and then <Enter> to install the defaults. Press
<Canel> and then <Enter> to not install the defaults. The optimized defaults place
demands on the system that may be greater than the performance level of the components,
such as the CPU and the memory. You can cause fatal errors or instability if you install
the optimized defaults when your hardware does not support them. If you only want to
install setup defaults for a specific option, select and display that option, and then press
<F9>.
Users please remain the factory BIOS default setting of “Load Optimized
Defaults” when install Operation System onto your system.
Save Changes and Exit
Highlight this item and press <Enter> to save the changes that you have made in the Setup
Utility and exit the Setup Utility. When the Save and Exit dialog box appears, select [OK]
to save and exit, or select [Cancel] to return to the main menu.
Discard Changes and Exit
Highlight this item and press <Enter> to discard any changes that you have made in the
Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears,
select [OK] to discard changes and exit, or select [Cancel] to return to the main menu.
If you have made settings that you do not want to save, use the “Discard
Changes and Exit” item and select [OK] to discard any changes you have
made.
Using BIOS
37
Chapter 4
Using the Motherboard Software
About the Software CD-ROM
The support software CD-ROM that is included in the motherboard package contains all the
drivers and utility programs needed to properly run the bundled products. Below you can find
a brief description of each software program, and the location for your motherboard
version. More information on some programs is available in a README file, located in the
same directory as the software.
Never try to install all software from folfer that is not specified for use with your
motherboard.
Before installing any software, always inspect the folder for files named README.TXT,
INSTALL.TXT, or something similar. These files may contain important information that
is not included in this manual.
Auto-installing under Windows 2000/XP
The Auto-install CD-ROM makes it easy for you to install the drivers and software for your
motherboard.
If the Auto-install CD-ROM does not work on your system, you can still install
drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.
The support software CD-ROM disc loads automatically under Windows 2000/XP. When
you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically
bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.
If the opening screen does not appear; double-click the file “setup.exe” in
the root directory.
Using the Motherboard Software
38
Setup Tab
Setup
Click the Setup button to run the software installation program. Select
from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that allows
you to open Windows Explorer and show the contents of the support
CD.
Before installing the software from Windows Explorer, look for a file
named README.TXT, INSTALL.TXT or something similar. This file
may contain important information to help you install the software
correctly.
Some software is installed in separate folders for different operating
systems. Always go to the correct folder for the kind of OS you are using.
In install the software, execute a file named SETUP.EXE or INSTALL.EXE
by double-clicking the file and then following the instructions on the
screen.
Exit
The EXIT button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the CD.
Read Me Tab
Displays the path for all software and drivers available on the CD.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1.
Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists will be
different according to the motherboard you are installing.
The motherboard identification is located in the upper left-hand corner.
Using the Motherboard Software
39
2.
Click Next. The following screen appears:
3.
Check the box next to the items you want to install. The default options are recommended.
4.
Click Next run the Installation Wizard. An item installation screen appears:
5.
Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the
installation.
Using the Motherboard Software
40
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory.
This file contains the information needed to locate the drivers for your motherboard.
Look for the chipset and motherboard model; then browse to the directory and path to
begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup
program located in the operating system subfolder.
If the driver you want to install does not have a setup program, browse to the operating
system subfolder and locate the readme text file (README.TXT or README.DOC) for
information on installing the driver or software for your operating system.
Utility Software Reference
All the utility software available from this page is Windows compliant. They are provided
only for the convenience of the customer. The following software is furnished under license
and may only be used or copied in accordance with the terms of the license.
These software(s) are subject to change at anytime without prior notice.
Please refer to the support CD for available software.
AMI/AWARD Flash Utility
This utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard,
and lets you copy an updated version of the BIOS to the chip. Proceed with caution when
using this program. If you erase the current BIOS and fail to write a new BIOS, or write a
new BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS for
more information.
WinFlash Utility
The Award WinFlash utility is a Windows version of the DOS Award BIOS flash writer utility.
The utility enables you to flash the system BIOS stored on a Flash Memory chip on the
motherboard while in a Windows environment. This utility is currently available for
WINXP\2000. To install the WinFlash utility, run WINFLASH.EXE from the following
directory: \UTILITY\WINFLASH 1.51
This concludes Chapter 4.
Using the Motherboard Software
La 915PL-A2 utilise un type LGA775 de Pentium 4 présentant les fonctionnalités suivantes:
•
•
•
Reçoit des processeurs Intel P4/ Celeron
Support un bus système (FSB) de 800/533 MHz
Supporte le CPU de technologie “Hyper-Threading”
La technologie “Hyper-Threading” permet au système d’exploitation de penser qu’il est connecté
à deux processeurs, permettant d’exécuter deux threads en parallèle, à la fois sur des processeurs
‘logiques’ dans le même processeur physique.
Chipset
Le chipset 915PL Northbridge (NB) Chipset et ICH6 Southbridge (SB) se base sur une architecture innovante et évolutive avec des performances et une fiabilité éprouvées.
915PL(NB)
•
•
•
•
Prend en charge l’adressage de bus hôte 32 bits, permettant au
CPU d’accéder à l’espace de 4 Go complet d’adresse mémoire.
Possède une “12-deep In-Order Queue” pour prendre en charge
jusqu’à douze requêtes d’adresse en pipeline exceptionnelles sur
le bus hôte.
Prend en charge un PCI Express x16 pour Interface Graphique,
entièrement conforme à la Spécification de Base PCI Express
révision 1.0a.
Prend en charge les technologies DDR 256-Mb, 512-Mb et 1-Gb
pour x8 et x16 périphériques
Le chipset 915PL peut seulement prendre en charge les technologies DDR 256-Mb,
512-Mb et 1-Gb pour x8 et x16 périphériques, NE prend PAS en charge la technologie
DDR 128-Mb. C’est à dire que le Module Mémoire Double Face de 256 Mo & le
Module Mémoire Simple Face de 128 Mo NE sont PAS pris en charge.
ICH6 (SB)
•
•
•
•
•
•
•
•
Fonctions de Contrôleur DMA Amélioré, de contrôleur
d’interruption, et de minuterie
Conforme aux spécifications de base PCI Express, Révision 1.0a
Conforme aux spécifications PCI 2.3.
Conforme aux spécifications ATA 1.0a Série
Contrôleur d’Hôte USB 2.0 intégré prenant en charge jusqu’à huit
ports USB 2.0
Contrôleur LAN intégré
Conforme à la spécification Azalia prenant en charge 8 Canaux de
sorties audio
Contrôleur IDE intégré prenant en charge Ultra ATA100/66/33
Mémoire
•
•
•
Prend en charge les DIMM SDRAM DDR 400/333 MHz
Reçoit deux DIMM sans tampon
Jusqu’à 1 Go par DIMM avec une taille de mémoire maximum de 2 Go
Multi-Language Translation
Français
Caractéristiques
Processeur
Français
LAN sur carte (Optionnel)
Cette carte mère prend en charge les chipsets LAN suivants :
•
Supporte le fonctionnement en Auto-négociation N-way en 100/10 Mb/s
•
Conforme à PCI Revision 2.2
•
Prend en charge le Contrôle de Flux Full Duplex (IEEE 802.3x)
•
Alimentation de 2,5/3,3V avec tolérance d’E/S de 5V
Audio
•
•
•
•
Conforme aux spécifications AC’97 2.3
Répond aux exigences de performances pour l’audio sur les systèmes PC99/2001
Convertisseurs DA à huit canaux avec vitesse de 48KHz
Conforme aux exigences audio de Microsoft SHQL/WLP 2.0
Options d’extension
La carte mère comporte les options d’extension suivantes :
•
•
•
•
•
•
Deux logements PCI Express x16 pour Interface Graphique
Un logement PCI Express x1
Trois emplacements PCI v2.3 bits
Un en-têtes demi-hauteur IDE de 40 broches supportant deux canaux IDE
Une interface lecteur de disquettes
Quatre connecteurs SATA à 7 broches
La 915PL-A2 carte mère prenant en charge la maîtrise de bus UltraDMA avec vitesses de transfert
de 100/66 Mo/s.
E/S intégrées
La carte mère comporte un ensemble complet de connecteurs et de ports E/S :
•
•
•
•
•
•
Deux ports PS/2 pour souris et clavier
Un port série
Un port parallèle
Quatre ports USB
Un port LAN (optionnel)
Prises audio pour entrée microphone, entrée de ligne et Audio Haute Définition 8
ch.
Microprogramme BIOS
La carte mère utilise AMI BIOS qui permet à l’utilisateur de configurer bon nombre de fonctions du
système, dont :
•
•
•
•
Gestion d’alimentation
Alertes de réveil
Paramètres de CPU
Synchronisation de CPU et de mémoire
Le micro-programme peut également être utilisé pour définir les paramètres pour différentes
vitesses d’horloge de processeur.
Certaines spécifications matérielles et certains éléments logiciels sont susceptibles
de modification sans préavis.
Multi-Language Translation
Leistungsmerkmale
Prozessor
•
Aufnahme eines Intel P4/Celeron-Prozessors.
•
Unterstützt einen Systembus (FSB) mit 800/533 MHz.
•
Unterstützt CPU mit “Hyper-Threading”-Technologie.
“Hyper-Threading”-Technologie läßt das Betriebssystem glauben, es sei an zwei Prozessoren angeschlossen, was zwei parallele Threads auf separaten ‘logischen’ Prozessoren im selben physischen
Prozessor erlaubt.
Chipsatz
Der 915PL Northbridge (NB)- sowie ICH6 Southbridge (SB)-Chipsatz basiert sich auf eine innovative
und skalierbare Architektur mit bewiesenr Zuverlässigkeit und Leistung.
915PL (NB)
•
•
•
•
Unterstützung einer 32-Bit Host-Bus-Adressierung, welche der
CPU einen Zugriff zum kompletten Speicherplatz von 4 GB
erlaubt.
Zur Unterstützung von bis zu 12 aufeinanderfolgenden
offenstehenden Befehlen im Host Bus, hat er eine 12fach
verstärkte Reihenfolgewarteschlange.
Unterstützung von PCI Express x16 für die Grafikschnittstelle,
gemäß den PCI Express-Base-Spezifikationen Revision 1.0a.
Unterstützung von 256-Mb, 512-Mb und 1-Gb DDRTechnologien für x8 und x16 Zubehör.
Das 915PL Chipset kann nur 256-Mb, 512-Mb und 1-Gb DDR-Technologien für
x8 und x16 Zubehör unterstützen; KEINE Unterstützung für die 128-Mb DDRTechnologie. Das bedeutet, daß das 256 MB Double Side Memory Modul & 128 MB
Single Side Memory Modul nicht unterstützt wird.
ICH6 (SB)
•
•
•
•
•
•
•
•
Verbesserter DMA-Kontroller, Unterbrechungskontroller und
Zeitfunktionen.
Gemäß PCI Express-Base-Spezifikationen, Revision1.0a.
Gemäß Spezifikationen von PCI 2.3.
Gemäß Serial ATA 1.0a Spezifikationen.
Integrierter USB 2.0 Host-Kontroller, welcher bis zu acht USB
2.0 Steckvorrichtungen unterstützt.
Integrierter LAN-Kontroller.
Gemäß Azalia-Spezifikation, mit Unterstützung von 8 AudioOutput-Kanälen.
Integrierter IDE-Kontroller, welcher Ultra ATA100/66/33
unterstützt.
Arbeitsspeicher
•
•
•
Unterstützung von DDR 400/333 MHz DDR SDRAM DIMMs.
Es können zwei ungepufferte DIMMs aufgenommen werden.
Bis zu 1 GB pro DIMM mit maximaler Speicherkapazität von bis zu 2 GB.
Multi-Language Translation
Deutsche
Der 915PL-A2 benutzt einen Pentium 4 des Typs LGA775 und besitzt folgende Eigenschaften:
Onboard LAN (Optional)
Das Onboard-LAN hat die folgenden Leistungsmerkmale:
Deutsche
•
•
•
•
Audio
•
•
•
•
Unterstützt 100/10 Mb/Sek N-way Auto-negotiation Betrieb
Entspricht PCI Revision 2.2
Unterstützt Vollduplex-Flusskontrolle (IEEE 802.3x)
2,5/3,3V Netzteil mit 5V Toleranz I/Os
Entspricht AC’97 2.3 Spezifikationen
Entspricht den Leistungsanforderungen für Audio auf PC99/2001 Systemen
Acht Kanäle DA Wandler mit 48KHz
Entspricht den Microsoft SHQL/WLP 2.0 Audio-Anforderungen
Erweiterungsmöglichkeiten
Das Motherboard ist mit den folgenden Erweiterungsmöglichkeiten ausgestattet:
•
Zwei PCI-Express x16 Slots für eine Grafikschnittstelle
•
•
Ein PCI Express x1 Slot
Drei 32-bit PCI v2.3-Steckplätze
•
Einen 40-Pin IDE low profile-Stecker, die zwei IDE-Kanäle unterstützen
•
Ein Diskettenlaufwerkanschluss
•
Vier 7-Pin SATA-Stecker
Der 915PL-A2 Motherboard unterstützt UltraDMA Bus Mastering mit einer Übertragungsrate von
100/66 MB/Sek.
Integrierte I/O
Das Motherboard hat einen vollständigen Satz von I/O-Schnittstellen bzw. -Anschlüssen:
•
Zwei PS/2-Anschlüsse für Maus und Tastatur
•
Eine serielle Schnittstelle
•
Eine parallele Schnittstelle
•
Vier USB-Anschlusse
•
Ein LAN- Steckplatz (optional)
•
Audiostecker fur Mikrofoneingang, line-in und hoch definiertem Ton mit 8 Kanalen
BIOS-Firmware
Das Motherboard verwendet AMI BIOS, das es Benutzern gestattet, viele Systemfunktionen inkl.
der Folgenden zu konfigurieren:
•
Energieverwaltung
•
Aufweckfunktionen
•
CPU-Parameter
•
CPU- und Arbeitsspeicherfrequenz
Die Firmware kann auch zur Einstellung von Parametern für verschiedene Prozessortaktgeschwindigkeiten verwendet werden.
Manche Hardwarespezifikationen und Softwareelemente können ohne Ankündigung
geändert werden.
Multi-Language Translation
Il 915PL-A2 sfrutta un Pentium 4 di tipo LGA775 che dispone delle seguenti caratteristiche:
•
Alloggia processori Intel P4/Celeron
•
Supporta un bus di sistema (FSB) fino a 800/533 MHz
•
Supporta CPU con tecnologia “Hyper-Threading”
La tecnologia “Hyper-Threading” induce il sistema operativo a pensare di essere collegato
a due processori, questo permette di eseguire due thread in parallelo, ambedue su processori
“logicamente” separati all’interno dello stesso processore.
Chipset
I chipset 915PL Northbridge (NB) e ICH6 Southbridge (SB) sono basati su una architettura
innovativa e scalabile dalle prestazioni e affidabilità garantite.
•
Supporta un indirizzamento host bus da 32 bit, consentendo alla
915PL (NB)
CPU di accedere a tutti i 4 GB della memoria di sistema.
•
Dispone di una coda in ordine per supportare sino a dodici
richieste di indirizzo pipelined in sospeso sull’host bus.
•
Supporta un PCI Express x16 per interfaccia grafica,
completamente compatibile con le specifiche di revisione 1.0a
di PCI Express Base.
•
Supporta tecnologie DDR da 256-Mb, 512-Mb e 1-Gb per
dispositivi x8 e x16
Il chipset 915PL può supportare solo tecnologie DDR da 256-Mb, 512-Mb e 1Gb per dispositivi da x8 e x16, NON supporta tecnologie DDR da 128-Mb. Cioè,
non sono supportati moduli di memoria Double Side da 256-MB e moduli di
memoria Single Side da 128-MB.
ICH6 (SB)
•
•
•
•
•
•
•
•
Controller DMA migliorato, controller interrupt e funzioni di
timer
Compatibile con le Specifiche di base del PCI Express,
Revision1.0a
Conforme alle specifiche PCI 2.3.
Conforme alle specifiche Serial ATA 1.0a
Host Controller USB 2.0 integratoin grado di supporare sino a 8
porte USB 2.0
Controller LAN integrato
Compatibile con le specifiche di Azalia in grado di supportare 8
canali di audio output
Integrato con controller IDE supporta Ultra ATA100/66/33
Memoria
•
•
•
Supporta DDR 400/333 MHz DDR SDRAM DIMM
Alloggia 2 DIMM unbuffered
Dimensione massima della DIMM pari ad 1 GB per un ammontare massimo di 2
GB di memoria
Multi-Language Translation
Italiano
Caratteristiche
Processore
LAN Onboard (Opzionale)
La LAN su scheda fornisce le seguenti caratteristiche:
•
Supporta operazioni di auto-negoziazione N-way a 100/10 Mb/s
•
Conforme a PCI Revision 2.2
•
Supporto di controllo flusso full duplex (IEEE 802.3x)
•
Alimentazione a 2,5/3,3 V con ingressi/uscite con tolleranza di 5 V
Italiano
Audio
•
•
•
•
Conforme alle specifiche AC’97 2.3
Conforme ai requisiti di prestazione audio su sistemi PC99/2001
Otto canali di conversione audio digitale a 48 KHz
Conforme ai requisiti audio di SHQL e WLP 2.0 di Microsoft
Opzioni di espansione
La scheda madre è dotata delle seguenti opzioni di espansione:
•
Due slot PCI Express x16 per interfaccia grafica
•
Un PCI Express x1
•
Tre slot PCI v2.3 a 32 bit
•
Una connettori IDE a 40 pin che supportano due canali IDE
•
Una interfaccia floppy disk
•
Quattro connettori SATA a 7 pin
La scheda madre 915PL-A2 supporta bus master UltraDMA con tasso di trasferimento di
100/66 MB/s.
I/O integrato
La scheda madre è dotata di un set completo di connettori e porte I/O:
•
Due porte PS/2 per mouse e tastiera
•
Una porta seriale
•
Una porta parallela
•
Quattro porte USB
•
Una porta LAN (opzionale)
•
Jack audio per microfono, line-in e 8 canali audio ad alta definizione.
Firmware BIOS
Questa scheda madre adotto un BIOS AMI che permette agli utenti di configurare le
caratteristiche principali del sistema, inclusi:
•
•
•
•
Gestione energia
Allarmi wake up
Parametri CPU
Temporizzazione CPU e memoria
Il firmware può anche essere usato per impostare i parametri per diverse velocità di clock.
Alcune specifiche hardware e software potrebbero essere soggette a
cambiamenti senza preavviso.
Multi-Language Translation
Características
Procesador
La 915PL-A2 usa un tipo LGA775 de Pentium 4 que lleva las sigtes. características::
Acomoda los procesadores Intel P4/Celeron
Soporta un sistema de bus (FSB) de 800/533 MHz
Soporta CPU de tecnología “Hyper-Threading”
La tecnología “Hyper-Threading” habilita el sistema operativo para que piense como si
estuviera conectado a dos procesadores, que permite dos hilos a correr en paralelo, ambos en
procesadores “lógicos” dentro del mismo procesador físico.
Chipset
Los chipsets Northbridge 915PL (NB) y Southbridge ICH6 (SB) están basados en una arquitectura
innovadora y escalable con fiabilidad y rendimiento comprobados.
915PL (NB)
•
•
•
•
Soporta la dirección de bus anfitrión 32-bit, que permite la CPU
acceder a todos los 4 GB del espacio de dirección de memoria.
Tiene 12-deep In-Order Queue (Fila En Orden de Profunidad
12) para soportar hasta 12 pedidos de dirección sobresalientes
en el bus anfitrión.
Soporta un PCI Express x16 para la Interfaz de Gráficas,
completamente conforme a la Especificación Base PCI Express
revisión 1.0a.
Soporta las tecnologías 256-Mb, 512-Mb y 1-Gb DDR para los
dispositivos x8 y x16.
El chipset 915PL solamente puede soportar las technologías 256-Mb, 512-Mb y 1-Gb DDR
para los dispositivos x8 y x16, NO soporta la tecnología 128-Mb DDR. Es decir, NO soporta
el Módulo de Memoria de Doble Lado 256 MB & Módulo de Memoria de Lado Singular
128 MB.
ICH6 (SB)
•
•
•
•
•
•
•
•
Controlador DMA reforzado, controlador de interrupción y funciones de cornometraje.
Conforme con la Especificación Base PCI Express,
Revisión1.0a.
Conforme con la espec. PCI 2.3.
Conforme con la espec. Serial ATA 1.0a
Controlador Anfitrión USB 2.0 Integrado soporta hasta ocho
puertos USB 2.0.
Controlador LAN integrado .
Conforme con la especificación Azalia que soporta 8 canales de
salidas de sonido.
Controlador IDE integrado soporta Ultra ATA100/66/33.
Memoria
•
•
•
Soporta DDR 400/333 MHz DDR SDRAM DIMMs
Acomoda dos DIMMS sin buffer
Hasta 1 GB por DIMM con el tamaño de memoria máximo hasta 2 GB
Multi-Language Translation
Español
•
•
•
LAN en placa (Optativo)
La LAN en placa proporciona las características siguientes:
•
Soporta la operación de auto-negociación de 100/10 Mb/s N-way
•
Conformidad de la PCI Revisión 2.2
•
Soporta Full Duplex Flow Control (IEEE 802.3x)
•
Suministro de 2.5/3.3V con I/Os tolerantes de 5V
Audio
Español
•
•
•
•
Conformidad con las especificaciones AC’97 2.3
Satisface los requisitos de rendimiento para el audio en los sistemas PC99/2001
Transformadores DA de Ocho Canales con un índice de 48KHz
Satisface los requisitos de audio de Microsoft SHQL/WLP 2.0
Opciones de expansión
La placa base viene con las opciones siguientes de expansión:
•
Dos ranuras PCI Express x16 para la Interfaz de Gráficas
•
Un PCI Express x1
•
Tres ranuras conforme con 32-bit PCI v2.3
•
Una cabezal de perfil bajo 40-pin IDE dos soporta cuatro canales IDE
•
Una interfaz para unidad de disquete
•
Cuatro conectores SATA de 7-pin
La placa principal 915PL-A2 soporta el mastering de bus UltraDMA con índices de
transferencia de 100/66 MB/s.
I/O integrado
La placa base tiene un conjunto completo de puertos I/O y conectores:
•
Dos puertos PS/2 para ratón y de teclado
•
Un puerto serie
•
Un puerto paralelo
•
Cuatro puertos USB
•
Un puerto LAN (optativo)
•
Clavijas de sonido para entrada de microfono, entrada de linea y Sonido de Alta
Definicion de 8 canales.
Firmware de BIOS
La placa base utiliza AMI BIOS que permite a los usuarios configurar muchas funciones
de sistema, incluyendo las siguientes:
•
Administración de energía
•
Alarmas de encendido
•
Parámetros CPU
•
Temporización de memoria y CPU
El firmware también puede utilizarse para ajustar los parámetros para diversas velocidades del
reloj del procesador.
Algunas especificaciones de hardware y elementos de software están sujetos a
cambios sin previo aviso.
Multi-Language Translation
Características
Processador
O 915PL-A2 usa um tipo LGA775 de Pentium 4 que possui as seguintes características:
•
Acomoda processadores Intel P4/Celeron
•
Suporta um bus sistema (FSB) de 800/533 MHz
•
Suporta CPU de tecnologia “Hyper-Threading”
A tecnologia “Hyper-Threading” permite que o sistema operativo “pense” que está ligado a
dois processadores, permitindo que sejam executados dois threads em paralelo, ambos em
processadores “lógicos” separados dentro do mesmo processador físico.
Os chipsets da 915PL Northbridge (NB) e ICH6 Southbridge (SB) são baseados em uma
arquitetura inovativa e escalável com performance e confiabilidade comprovada.
915PL (NB)
•
•
•
•
Suporta um endereçamento no host bus de 32-bit, permitindo que o
CPU aceda completamente aos 4 GB de espaço de endereçamento
da memória.
Possui uma Fila de Espera Em-Ordem com capacidade para 12
para suportar até doze pedidos de endereçamento estruturados e
pendentes no host bus.
Suporta um PCI Express x16 Interface de Gráficos, que cumpre
inteiramente com a revisão de Especificação de Base 1.0a. do
PCI Express.
Suporta 256-Mb, 512-Mb e tecnologias 1-Gb DDR para
aparelhos x8 e x16
Chipset (conjunto de chips) 915PL só consegue suportar tecnologias 256-Mb, 512Mb e 1-Gb DDR para aparelhos x8 e x16 , NÃO suporta tecnologia 128-Mb DDR. Ou
seja, NÃO suporta Módulo de Memória Bidireccional 256 MB & Módulo de Memória
Unidireccional 128 MB.
ICH6 (SB)
•
•
•
•
•
•
•
•
Controlador DMA Melhorado, controlador de interruptor, e funções
de temporizador
Cumpre com a Especificação de Base do PCI Express, Revisão
1.0a
Em conformidade com a especificação PCI 2.3
Compatível com Série ATA 1.0a
Controlador Host 2.0 USB integrado suportando até oito portas
USB 2.0
Controlador LAN integrado
Cumpre com a especificação Azalia suportando 8 Canais de
saídas áudio
Controlador IDE integrado suporta Ultra ATA100/66/33
Memória
•
•
•
Suporta DDR 400/333 MHz DDR SDRAM DIMMs
Acomoda duas DIMMs sem buffers
Até 1 GB por DIMM com tamanho de memória máxima de até 2 GB
Multi-Language Translation
Português
Chipset
Onboard LAN (Opcional)
O onboard LAN fornece as seguintes características:
•
Suporta o funcionamento de negociação automática de 100/10 Mb/s N-direcções
•
Compatível com a Revisão 2.2 PCI
•
Suporta Controlo de Fluxo Duplo Completo (IEEE 802.3x)
•
Fonte de alimentação 2.5/3.3V com I/Os tolerantes de 5V
Áudio
•
•
•
•
Cumpre com as especificações AC’97 2.3
Conversores DA com oito canais com taxa de 48KHz
Cumpre com os requisitos de performance para áudio em sistemas PC99/2001
Cumpre com os requisitos áudio WHQL/WLP 2.0 da Microsoft audio
Português
Opções de expansão
A motherboard possui as seguintes opções de expansão:
•
Duas ranhuras PCI Express x16 para Interface de Gráficos
•
Um 1 x PCI Express
•
Três ranhuras compatíveis com PCI v2.3 de 32 bits
•
Uma cabeçalhos de baixo perfil IDE 40 pinos, que suportam dois dispositivos
IDE
•
Uma interface para unidade de disquete
•
Quatro conectores SATA de 7 pinos
A motherboard 915PL-A2 suporta um domínio bus UltraDMA bus com taxas de
Transferência de 100/66 MB/s.
E/S integradas
A motherboard conta com um conjunto completo de portas e conectores E/S:
•
Duas portas PS/2 para o rato e o teclado
•
Uma porta de série
•
Uma porta paralela
•
Quatro portas USB
•
Uma porta LAN (opcional)
•
Fichas áudio para microfone, alinhadas e com Áudio de Elevada Definição 8-ch
Firmware do BIOS
A motherboard usa o AMI BIOS que permite aos usuários configurar vários recusos do
sistema, como:
•
Gerenciamento de energia
•
Alarmes de reativação
•
Parâmetros da CPU
•
Sincronização da CPU e memória
O firmware também pode ser usado para definir os parâmetros de diferentes velocidades de
clock do processador.
Alguns itens de software e especificação de hardware estão sujeitos a alterações
sem prévio aviso.
Multi-Language Translation
機能
プロセッサ
915PL-A2 はLGA775タイプのPentium 4に対応したもので、その特徴は次の通りで
す:
•
Intel P4 /Celeron プロセッサ取付け可能。
•
800/533MHzのシステムバス(FSB)をサポート。
•
“ハイパースレッド(Hyper-Threading)"技術対応のCPUを取り付け可能。
ハイパースレッド 技術というのは、オペレーションシステムに2つのプロセッサが存在すると認識させ
ることで、実際には2つのスレッドを1つのプロセッサで同時に執行させ、平行利用を可能とする技術
です。
チップセット
915PL (NB)
•
•
•
•
32ビットホストバスアドレシング機能対応、これでCPUが4 GBの
メモリアドレス空間すべてをアクセス可能。
12組ジャブ扱い可能の中順(In-Order)キュー採用、これでホス
トバスでの12つの未完成パイプライン・アドレス要求を対応。
グラフィックインターフェース用PCI Express x16 スロットを提
供、これでPCI Express Base Specification revision 1.0aに
完全対応。
8倍速または16倍速のデバイスの256-Mbや512-Mb、1-Gb の
DDR技術に対応。
915PLチップセットは8倍速または16倍速のデバイスの256-Mbや512Mb、1-Gb のDDR技術のみ対応。128-Mb DDR 技術は対応されません。
具体的に、256 MB二面メモリモジュールや128 MB 片面メモリモジュー
ルは対応されませんので、ご注意。
ICH6 (SB)
•
•
•
•
•
•
•
•
強化型DMAコントローラと、割り込みコントローラ、タイマー
機能を提供。
PCI Express Base Specification 1.0a版に完全対応。
PCI 2.3仕様に準拠しています。
シリアルATA 1.0a仕様に準拠し。
統合型USB 2.0ホストコントローラで、最大8つまでのUSB
2.0 ポートを対応可能。
統合型LANコントローラ。
Azalia規格に準拠で、8チャネルのオーディオ出力可能。
統合型IDEコントローラで、Ultra ATA100/66/33サポート
可能。
メモリ
•
•
•
DDR 400/333 MHzのDDR SDRAM DIMMに対応。
2つの非バッファーDIMMを搭載。
各DIMMスロットに1 GBまで装着可能で、合計2GBまでをサポート。
Multi-Language Translation
日本語
915PL Northbridge (NB)とICH6 Southbridge (SB)チップセットは、実証された信頼
性と性能を持つ革新的で拡張性のあるアーキテクチャに基づいています。
オンボードLAN (オプション)
当マザーボードは次のLANチップセットのいずれかを搭載しております:
•
100/10 Mb/秒のNウェイ自動認識機能動作をサポート
•
PCI 2.2に準拠
•
全二重フロー制御(IEEE 802.3x)をサポート
•
許容電圧5VのI/Oでの2.5/3.3V 電源サプライ
オーディオ
•
•
•
•
AC’97 2.3 規格に準拠
PC99/2001 システムに関するオーディオ要求に適合
48KHzでの8チャネルDA コンバーター
Microsoft SHQL/WLP 2.0 オーディオ要求に適合
拡張オプション
日本語
本マザーボードでは、次の拡張機能が利用できます。
•
•
•
•
•
•
PCI Express x16 スロットが2つ
PCI Express x1スロットが1つ
32ビットPCI v2.3 互換性スロットが3つ
40ピンIDEロープロフィルヘッダー(2つのIDEチャネルをサポート)が1つ
FD ドライブ インターフェイス が1つ
7ピン SATAコネクタが4つ
このマザーボードは、100/66 MB/秒の転送速度でのUltra DMAバスマスタリングをサ
ポートします。
統合I/O
マザーボードには、次のI/Oポートやコネクタを揃えています。
•
•
•
•
•
•
マウスとキーボード用のPS/2ポートが2つ
シリアルポートが1つ
パラレルポート が1つ
USBポート が4つ
LAN ポート(オプション)が 1つ
さらに、マイクロホン入力と、ライン入力と、8チャネルHigh Definition
Audio出力とを搭載
BIOSファームウェア
本マザーボードはAMI BIOSを採用し、次を含めた多様なシステム構成を行えます。
•
•
•
•
電源管理
ウェークアップアラーム
CPUパラメータ
CPUおよびメモリのタイミング
さらに、所定のパラメータを設定することによって、プロセッサのクロック速度を変更す
ることもできます。
ハードウェア仕様とソフトウェアアイテム が 、予告なしに変更することがありま
す。
Multi-Language Translation
특징
프로세서
915PL-A2 는 다음과 같은 특징을 지닌 팬티엄 4 의 LGA775 타입을 사용한다:
•
인텔 팬티엄 4 /Celeron 프로세서 사용
•
800/533 MHz시스템 버스(FSB) 지원
•
”Hyper-Threading”기술 CPU 지원
”Hyper-Threading”기술은 운영체제를 두 개의 프로세서에 연결한 것처럼 두개의
트래드를 패러럴로 실행하여 같은 물리적 프로세서 안에서 각기 다른 논리적 프로세
서를 실행할 수 있게 한다.
칩셋
915PL(NB)
•
•
•
•
32 비트 호스트 버스 어드레싱 지원으로, CPU 가 총 4 GB 메
모리 어드레스 공간에 액세스할 수 있다.
12-deep In-Order Queue 가 호스트 버스에서 최대 12 개의
파이프라인 어드레스 요청을 지원한다.
그래픽 인터페이스를 위해 1 개의 PCI Express x16 지원,
PCI Express Base 1.0a 사양 완전 부합.
x8 및 x16 장치를 위해 256-Mb, 512-Mb, 1-Gb DDR 기술 지
원.
915PL 칩셋은 x8 및 x16 장치를 위해 256-Mb, 512-Mb, 1-Gb DDR 기술만
을 지원하고, 128-Mb DDR 기술은 지원하지 않는다. 즉, 256 MB 양면 메모
리 모듈 및 128 MB 단면 메모리 모듈을 지원하지 않는다.
ICH6 (SB)
•
•
•
•
•
•
•
•
보강 DMA 컨트롤러, 인터럽트 컨트롤러, 및 타이머 기능
PCI Express Base 1.0a 사양 부합
PCI 2.3 사양 호환.
시리얼 ATA 1.0a 사양 호환
최대 8 개의 USB 2.0 포트를 지원하는 통합 USB 2.0 호스트
컨트롤러
통합 LAN 컨트롤러
오디오 출력에 8 개 채널을 지원하는 Azalia 사양 부합
통합 IDE 컨트롤러로 Ultra ATA100/66/33 지원
메모리
•
•
•
DDR 400/333 MHz DDR SDRAM DIMM 지원
2 개의 unbuffered DIMM 사용
DIMM 당 최대 1 GB, 최대 메모리 2 GB
Multi-Language Translation
한국인
915PL Northbridge (NB) 와 ICH6 Southbridge (SB) 칩셋은혁 신적이고 범위성을 지
닌 아키텍쳐를 바탕으로 인정된 신뢰성과 성능을 지닌다.
보드 내장 LAN (선택 사항)
본 마더보드는 다음과 같은 LAN 칩셋을 지원합니다:
•
100/10Mbps N-Way Auto-negotiation 작업 지원
•
PCI 2.2 사양 호환
•
Full Duplex Flow Control (IEEE 802.3x) 지원
•
2.5/3.3V 파워 써플라이 5V I/O
오디오
•
•
•
•
AC’97 2.3 사양 부합
PC99/2001 시스템의 오디오를 위한 퍼포먼스 요구 조건 부합
48KHz 의 8 채널 DA 컨버터
마이크로소프트 WHQL/WLP 2.0 오디오 요구 조건 부합
확장 옵션
한국인
이 메인보드는 다음과 같은 확장 옵션이 있다
•
그래픽 인터페이스를 위한 PCI 익스프레스 x16 2 개
•
PCI Express 1 개 x 슬롯1 개
•
32 비트 PCI v2.3 호환 슬롯 3 개
•
2 개의 IDE 채널을 지원하는 40 핀 IDE 로우 프로파일 해더 1 개
•
플로피 디스크 드라이브 인터페이스 1 개
•
7 핀 SATA 커넥터 4개
915PL-A2 마더보드는 전송 속도 100/66 MB/s의 UltraDMA 버스 마스터링을 지원
한다.
통합 I/O
이 메인보드에는 풀 세트의 I/O 포트와 커넥터가 있다
•
•
•
•
•
•
마우스와 키보드용 PS/2 포트 2 개
시리얼 포트1개
패러럴 포트 1 개
USB 포트 4 개
LAN 포트 (선택사항) 1 개
마이크 폰 입력, 라인 입력 및 8 채널 고 재생음 오디오를 위한 오디오 잭
BIOS 펌웨어
본 메인보드는 AMI BIOS 를 사용하여 사용자는 다음과 같은 시스템 기능을 구
성할 수 있다
•
전원 관리
•
Wake-up 알람
•
CPU 파라미터
•
CPU 및 메모리 타이밍
펌웨어는 다른 프로세서의 클럭 속도를 설정하는 데도 사용될 수 있다
하드웨어 사양 및 소프트웨어 아이템은 사전 통보없이 변경될 수 있
습니다
Multi-Language Translation
功能
處理器
915PL-A2 採用LGA775型的Pentium 4,具有如下特徵:
‧ 支援Intel P4/Celeron 處理器
‧ 支援高達800/533MHz之系統匯流排(FSB)
‧ 支援使用超執行緒(Hyper-Threading)技術之CPU
利用“超執行緒(HT)"技術,可使作業系統在相當於裝上了兩具處理器的狀態下運作
:利用一個"實體"處理器模擬出兩個獨立的"邏輯"處理器,同時執行兩個工作緒
。
晶片組
915PL (NB)
‧
‧
‧
‧
支援32位元主事匯流排定址,藉此CPU 存取整個4 GB的記憶
位址空間
具有一個可容納12組資料之跳序(In-order)佇列,可支援最多
12個在主控匯流排上發生的未完成管線位址要求
具有一個繪圖卡用之PCI Express x16 介面,完全符合PCI
Express Base Specification 1.0a版
支援8倍速及16倍速之256-Mb、512-Mb、及1-Gb DDR技術
915PL晶片組僅能支援8倍速及16倍速之256-Mb、 512-Mb、及1-Gb DDR技
術,惟,並不支援 128-Mb DDR 技術。具體而言,不支援256 MB雙面記憶
體模組及128 MB單面記憶體模組。.
ICH6 (SB)
‧
‧
‧
‧
‧
‧
‧
‧
增強型DMA控制器、中斷控制器、及計時功能
符合PCI Express Base Specification 1.0a版
符合PCI 2.3規格
符合序列ATA 1.0a規格;
內建式USB 2.0主控,可支援8個USB 2.0埠
內建式區域網路控制器
符合Azalia規格,支援8聲道音訊輸出
整合式IDE控制器,支援Ultra ATA100/66/33
記憶體
‧
‧
‧
支援DDR 400/333 MHz DDR SDRAM DIMM
可安裝2個非緩衝式DIMM
各DIMM可安裝1GB記憶體,共可支援高達2GB的記憶體容量
Multi-Language Translation
繁體中文
915PL北橋(NB)及ICH6南橋(SB)晶片組在研發設計上採用了創新且具擴充性之架構,具
備優良的可靠性及性能。
機載區域網路 (選購)
機載區域網路提供下列功能:
‧ 支援 100/10 Mb/秒N向自動辨識連線功能
‧ 相容於PCI 2.2版規格
‧ 支援全雙工流量控制(IEEE 802.3x)
‧ 2.5/3.3V 電源供應,具有容限電壓為5V的I/O
音效
•
•
•
•
相容於AC’97 2.3 規格
8通道DA 轉換器,具48KHz 頻率
符合PC99/2001系統音訊標準要求
符合Microsoft SHQL/WLP 2.0 音訊標準
擴充選項
繁體中文
本主機板包括下列擴充選項:
‧ 2 個繪圖卡用PCI Express x16 介面
‧ 1 個PCI Express x1 槽
‧ 3 個32位元PCIv2.3插槽
‧ 1個40針IDE低通接頭(支援2個IDE通路)
‧ 1 個軟碟機介面
‧ 4個 7針型SATA連接器
本主機板支援傳輸率100/66 MB/秒下的Ultra DMA 匯流排主控功能。
整合輸出入埠
主機板具有一組齊全的輸出入埠及連接器:
‧ 2 個 PS/2 埠,供滑鼠與鍵盤使用
‧ 1 個串列埠
‧ 1 個平行埠
‧ 4 個USB埠
‧ 1個LAN埠(選購)
‧ 具有麥克風輸入端子、線級輸入端子、及 8聲道高傳真音效(High Definition
Audio)輸出端子
BIOS 韌體
本主機板使用AMI BIOS,使用者可以組態設定許多系統功能,包括如下:
‧ 電源管理
‧ 喚醒警鈴
‧ CPU參數
‧ CPU及記憶體的時脈定時
此外,也可藉由參數的設定,調整處理器的時脈速度。
部份硬體規格和軟體內容可能會在未經通知的情況下更動,敬請見諒。
Multi-Language Translation
功能
处理器
915PL-A2 使用 LGA775 型 Pentium 4 CPU,具备以下特点:
•
•
•
支持 Intel P4/Celeron 处理器
支持 800/533 MHz 系统总线 (FSB)
支持“多线程(Hyper-Threading)”技术 CPU
“多线程”技术可以让操作系统认为自己连接了两个处理器,允许两个线程并行运行
,每个线程位于同一处理器中的单独“逻辑”处理器中。
芯片组
915PL 北桥 (NB) 和 ICH6 南桥 (SB) 芯片组是基于一种新型的、可扩展的架构,能
提供已经证明的可靠性和高性能。
•
•
•
•
支持 32 位主机总线寻址,允许 CPU 访问 4 GB 的完整内
存地址空间。
带 12-deep In-Order Queue,主机总线上最多支持 12 个
Piplined 地址请求。
支持 1 个 PCI Express x16 用于图形接口,完全符合 PCI
Express Base 规格 1.0a。
支持用于 x8 和 x16 设备的 256-Mb、512-Mb 和 1-Gb
DDR 技术
915PL 芯片组仅支持用于 x8 和 x16 设备的 256-Mb、512-Mb 和 1-Gb
DDR 技术,不支持 128-Mb DDR 技术。也就是说该芯片组不支持 256
MB 双面内存模块和 128 MB 单面内存模块。
ICH6 (SB)
•
•
•
•
•
•
•
•
增强 DMA 控制器、中断控制器和定时器功能
符合 PCI Express Base 规格 1.0a
符合 PCI 2.3 规格
符合串行 ATA 1.0a 规格
集成 USB 2.0 主控器,最多支持 8 个 USB 2.0 端口
集成 LAN 控制器
符合 Azalia 规格,支持 8 声道音频输出
集成 IDE 控制器,支持 Ultra ATA100/66/33
内存
•
•
•
支持 DDR 400/333 MHz DDR SDRAM DIMM
支持 2 个非缓冲 DIMM
每个插槽支持 1 GB,总共最大可支持 2 GB
Multi-Language Translation
简体中文
915PL (NB)
Onboard LAN (可选)
此主板支持以下任何一种 LAN 芯片组:
•
支持 100/10 Mb/s N 路自协商工作
•
兼容 PCI 2.2 版本
•
支持全双工流控制 (IEEE 802.3x)
•
2.5/3.3V 电源,支持 5V I/O
音频
•
•
•
•
兼容 AC’97 v2.3 规格
8 通道 DA 转换器,48KHz 速率
符合 PC99/2001 系统音频要求
符合 Microsoft SHQL/WLP 2.0 音频要求
扩展选项
此主板提供如下扩展选项:
•
2 个用于图形接口的 PCI Express x16
•
1 个 PCI Express x1 插槽
•
3 个 32 位 PCI v2.3 扩展槽
•
1 个 40-pin IDE 紧凑型接口,支持 2 个 IDE 通道
•
1 个软驱接口
•
4 个 7 针 SATA 接口
主板915PL-A2支持 Ultra DMA 总线控制,传输速率可达 100/66 MB/sec。
简体中文
集成 I/O
此主板具有完整的 I/O 端口和插孔:
•
2 个用于连接鼠标和键盘的 PS/2 端口
•
1 个串口
•
1 个并口
•
4 个 USB 端口
•
1 个 LAN 端口(可选)
•
用于麦克风、线入和 8 声道高清晰度音频的音频插孔
BIOS
此主板使用 AMI BIOS,可以让用户自己配置以下系统功能:
•
电源管理
•
唤醒报警
•
CPU 参数
•
CPU 和记忆的定时
还可用于设置不同处理器时钟速度的参数。
某些硬件规格和软件项目若有更改恕不另行通知。
Multi-Language Translation
Процессор
Плата 915PL-A2 построена на базе процессора Pentium 4 LGA775 и обладает
следующими характеристиками:
•
Размещает процессоры Intel P4/Celeron
•
Поддерживает системные шины (FSB) с частотой 800/533MHz
•
Поддерживает технологию CPU “Hyper-Threading”
Технология “Hyper-Threading” «убеждает» операционную систему в том, что в машине
имеется два процессора; это позволяет параллельно обслуживать два процесса, причем
каждый из процессов обслуживается отдельным «логическим» процессором в пределах
одного физического процессора.
Чипсет
Чипсет 915PL поддерживает только технологии 256-Мб, 512-Мб and 1-Гб
DDR для устройств x8 / x16 и НЕ ПОДДЕРЖИВАЕТ технологии 128-Мб
DDR. Таким образом, поддержка модулей памяти 256 МБ Double Side и 128
МБ Single Side ОТСУТСТВУЕТ.
ICH6 (SB)
•
•
•
•
•
•
•
•
Расширенные функции контроллера DMA, контроллера
прерываний, внутреннего таймера
Совместимость с PCI Express Base, Rev. 1.0a
Совместимость с PCI 2.3
Совместимость с Serial ATA 1.0a
Встроенный контроллер хоста USB 2.0 с поддержкой до
восьми портов USB 2.0
Встроенный контроллер LAN
Совместимость с технологией Azalia, поддержка 8канального аудиовыхода
Встроенный контроллер IDE с поддержкой Ultra ATA100/66/
33
Память
•
•
•
Поддержка памяти DDR 400/333 MГц DDR SDRAM DIMM
Обслуживает 2 модуля небуферизованной памяти DIMM
Обслуживает до 1 ГБ на модуль DIMM (максимально до 2 ГБ памяти)
Multi-Language Translation
Русский
Чипсеты 915PL «Северный мост» (Northbridge, NB) и ICH6 «Южный мост»
(Southbridge, SB) построены с использованием инновационной масштабируемой
архитектуры, обеспечивающей высокую надежность и производительность.
•
Поддерживает 32-битную адресацию хоста, обеспечивая для
915PL(NB)
CPU адресацию памяти объемом 4ГБ .
•
Поддерживает технологию 12-deep In-Order Queue,
обеспечивающую обслуживание до двенадцати заданий,
ожидающих на шине хоста.
•
Имеет один разъем для подключения карты графики PCI
Express x16; обеспечивает полную соместимость с PCI
Express Base, rev. 1.0a.
•
Поддерживает технологии 256-Мб, 512-Мб и 1-Гб DDR для
устройств x8 и x16
Встроенный сетевой адаптер LAN (опционально)
Встроенный сетевой адаптер LAN обладает следующими характеристиками:
•
Поддерживает автоматическое определение скорости и режима соединения
100/10Mb/s
•
Совместимость c PCI вер. 2.2
•
Поддерживает режим управления потоком Full Duplex Flow Control (IEEE
802.3x)
•
Электропитание 2.5/3.3V при допустимости 5V на входе/выходе
Аудио
•
•
•
•
Совместимость со спецификацией AC’97 2.3
8-канальный DA конвертер с частотой 48 КГц
Соответствие требованиям для аудио в системах PC99/2001
Соответствие требованиям для аудио Microsoft WHQL/WLP 2.0
Возможности расширения
Существуют следуюшие опции расширения данной материнской платы:
•
Один разъем для карты графики PCI Express x16
•
Два слота PCI Express x1
•
Три 32-битных слота PCI v2.3
•
Один низкопрофильный 40-штырьковый слот IDE, обеспечивающий
поддержку двух устройств IDE
•
Один разъем для накопителя на гибких дисках
•
Четыре 7-штырьковых коннектора SATA
Плата 915PL-A2 поддерживает технологию захвата управления шиной UltraDMA bus
mastering со скоростью передачи данных 100/66 МБ/сек.
Русский
Интегрированный вход/выход
Плата снабжена полным набором портов входа/выхода и разъемов:
•
Два порта PS/2 для подключения мыши и клавиатуры
•
Один серийный порт
•
Один параллельный порт
•
Четыре порта USB
•
Один порт LAN (опционально)
•
Гнездо для подключения микрофона, гнездо аудио-входа и 8-канального
аудиовыхода
BIOS
Плата работает под AMI BIOS, который позволяет пользователю конфигурировать
различные характеристики системы:
•
Управление питанием
•
Сигналы пробуждения системы
•
Параметры CPU
•
Время доступа для CPU и памяти
BIOS допускает также установку параметров для различных частот процессора.
Некоторые параметры платы и характеристики ее программного
обеспечения могут быть изменены без предварительного уведомления.
Multi-Language Translation
Cechy
Procesor
Płyta główna 915PL-A2 zaopatrzona jest w procesor Pentium 4 typu LGA775 i
charakteryzuje się następującymi cechami:
•
Obsługuje procesory Intel P4/Celeron
•
Obsługuje szynę systemowa (FSB) 800/533MHz
•
Zabezpiecza technologię CPU “Hyper-Threading”
Technologia “Hyper-Threading” powoduje, że system "myśli”, że posiada dwa procesory i
wykonuje równolegle dwa procesy; za wykonanie każdego procesu odpowiedzialny jest jeden
z dwuch "logicznych" procesorów w ramach jednego fizycznego procesora
Chipset
Mostek północny (NB) 915PL i mostek południowy (SB) ICH6 chipsetu oparty jest na
nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i funkcjonalnoœci.
915PL (NB)
•
•
•
•
Obsługuje 32-bitowe adresowanie hosta pozwalając procesorowi
zaadresować 4 GB pamięci
Posiada technologię 12-deep In-Order Queue i przetwarza do
dwunastu żądań oczekujących na szynie hosta.
Obsługuje jedno złącze grafiki PCI Express x16; całkowicie
zgodne z technologią PCI Express Base, w wersji 1.0a.
Obsługuje pamięci 256-Mb, 512-Mb i 1-Gb w technologii DDR
w urządzeniach x8 i x16
ICH6 (SB)
•
•
•
•
•
•
•
•
Rozszerzony kontroler DMA, kontroler przerywań i funkcje
zegara
Zgodny z technologią PCI Express Base, Rev. 1.0a
Zgodny z PCI w wersji 2.3
Zgodny ze standardem Serial ATA 1.0a
Wbudowany kontroler hosta USB 2.0 obsługuje do ośmiu
portów USB
Wbudowany kontroler LAN
Zgodny z technologią Azalia: zapewnia 8-kanałowe wyjście
audio
Wbudowany kontroler IDE obsługujący Ultra ATA100/66/33
Pamięć
•
•
•
Obsługuje pamięci typu DDR 400/333 MHz DDR SDRAM DIMM
Zaopatrzony w dwa gniazda niebuforowanej pamięci typu DIMM
Obsługuje pamięć DIMM do pojemności 1 GB każda; maksymalna możliwa
pojemność pamięci do 2 GB
Multi-Language Translation
Polski
Chipset 915PL obsługuje tylko pamięci 256-Mb, 512-Mb i 1-Gb w technologii DDR dla
urządzeń x8 i x16 I NIE OBSŁUGUJE pamięci 128-Mb w technologii DDR. To oznacza,
że pamięci 256 MB Double Side i 128 MB Single Side NIE SĄ OSŁUGIWANE.
Zintegrowana obsługa sieci LAN (opcjonalnie)
Zintegrowana obsługa sieci LAN posiada następujące właściwości:
•
Obsluguje N-drożne automatycznie ustalane operacje z szybkościami 100/10 Mb/s
•
Zgodny z PCI Revision\ w wersji 2.2
Obsługuje Full Duplex Flow Control (zgodnie ze standardem IEEE 802.3x)
•
•
Zasilacz 2.5/3.3V który toleruje We/Wy 5V
Audio
•
•
•
•
Zgodne ze specyfikacją AC’97 w wersji 2.3
Konwertuje sygnały ośmiokanałowego DA z częstotliwością 48KHz
Spełnia wymagania dla audio w systemie PC99/2001
Spełnia wymagania stawiane audio przez firmę Microsoft w systemie SHQL/WLP
2.0
Możliwości rozbudowy
Płyta głwna wyposażona jest w następujące gniazda:
•
Dwa gniazda PCI Express x16 dla karty graficznej
•
Jedno gniazdo typu PCI Express x1
•
Trzy 32-bitowych gniazda zgodnych z PCI w wersji 2.3
•
Jedno 40-nóżkowe złącze niskoprofilowe obsługujące dwa urządzenia IDE
•
Jedno złącze obsługujące stacje dyskietek
•
Cztery 7-nóżkowe złącza SATA
Płyta główna 915PL-A2 obsługuje szynę UltraDMA z szybkością transferu 100/66 MB/s.
Zintegrowane We/Wy
Polski
Płyta głwna wyposażona jest w pełny zestaw gniazd i złączy We/Wy:
•
Dwa gniazda PS/2 dla myszy i klawiatury
•
Jedno gniazdo szeregowe
•
Jedno gniazdo równoległe
•
Cztery gniazda USB
•
Jedno gniazdo LAN (opcjonalnie)
•
Wejście mikrofonowe, wejście audio i 8-kanałowe wyjście High Definition Audio
Firmowy BIOS
Płyta głwna wyposażona jest w BIOS firmy AMI, który pozwala użytkownikowi
konfigurować wiele cech systemu włączając w to następujące właściwości:
•
Zarządzanie poborem mocy
•
Alarmy typu Wake-up
•
Parametry pracy procesora
•
Ustalenia szybkoœci pracy procesora i pamiêci
BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara
procesora.
Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie
bez uprzedniego powiadomienia.
Multi-Language Translation
Vlastnosti
Procesor
Základní deska 915PL-A2 je urèena pro procesory Pentium 4 LGA775 a mùže nabídnout
následující vlastnosti:
•
Pro připojení procesorů Intel P4/Celeron
•
Podporuje taktování systémové sběrnice (FSB) na frekvenci 800/533 MHz
•
Podporuje technologii CPU „Hyper-Threading“
Technologie „Hyper-Threading“ umožňuje operačnímu systému pracovat tak, jako by byl
připojen ke dvěma procesorům, protože je možné pracovat se dvěma toky programového
kódu (vlákny) paralelně najednou, přičemž jsou k dispozici samostatné „logické“ procesory
umístěné v rámci jednoho fyzického procesoru.
Čipová sada
Čipy northbridge (NB) 915PL a southbridge (SB) ICH6 jsou založeny na inovativní a
škálovatelné architektuře s ověřenou spolehlivostí a výkonností.
•
Podporuje 32bitové adresování, umožòující CPU pøistupovat k
915PL (NB)
celému adresovému prostoru pamìti 4 GB.
•
Má 12stupòovou frontu pro podporu až 12 požadavkù na
adresování v pipeline na hostitelské sbìrnici.
•
Podpora jednoho rozhraní PCI Express x16 pro grafiku, zcela
splòující základní požadavky standardu PCI Express, revize
1.0a.
•
Podpora 256-Mb, 512-Mb a 1-Gb DDR technologií pro zaøízení
x8 a x16
ICH6 (SB)
•
•
•
•
•
•
•
•
Vylepšený řadič DMA, řadič přerušení a funkcí časovače
Splňuje základní požadavky standardu PCI Express, revize 1.0a
Splňuje požadavky standardu PCI 2.3
Splňuje požadavky standardu Serial ATA 1.0a
Integrované hostitelské řadiče USB 2.0 podporující až osm
portů
Integrovaný řadič LAN
Splňuje požadavky standardu Azalia, který podporuje 8
kanálový zvukový výstup
Integrovaný řadič IDE podporující Ultra ATA100/66/33
Paměť
•
•
•
Podporuje pamì ové moduly DDR 400/333 MHz DDR SDRAM DIMM
Instalovat je možné až dva DIMM moduly bez vyrovnávací pamìti
Až 1 GB pamìti na jeden modul DIMM s maximální velikostí pamìti do 2 GB
Multi-Language Translation
Česky
Čipová sada 915PL je schopná podporovat pouze technologie 256-Mb, 512Mb a 1 Gb DDR pro zařízení x8 a x16, NIKOLIV technologie 128-Mb DDR.
To znamená, že NEJSOU podporovány paměťové moduly 256 MB DIMM & 128
MB SIMM.
Vestavění síťové rozhraní LAN (volitelně)
Vestavěné síťové rozhraní LAN nabízí následující možnosti:
•
Podpora 100/10Mb/s N–cestného automatického přepínání provozu
•
Splňuje požadavky standardu PCI verze 2.2
•
Podpora plně duplexního řízení toku dat (IEEE 802.3x)
•
Napájení 2,5/3,3 V s obvody I/O tolerujícími napětí 5 V
Zvuk
Splňuje požadavky standardu AC’97 2.3
Splňuje výkonnostní požadavky pro audio zařízení na systémech PC99/2001
Osmikanálové převodníky DA se vzorkovací frekvencí 48 kHz
Splňuje požadavky pro audio zařízení Microsoft SHQL/WLP 2.0
•
•
•
•
Možnosti rozšíření
Základní deska je dodávána s následujícími možnostmi rozšíření
•
Dvě patice PCI Express x16 pro grafickou kartu
•
Jedna patice PCI Express x1
•
Tři 32bitové patice PCI v2.3
•
Jeden nízkoprofilový 40kolíkový konektor IDE podporující připojení dvou
zařízení standardu IDE
•
Jedno rozhraní pro disketovou mechaniku
•
Čtyři 7kolíkové konektory SATA
Základní deska 915PL-A2 podporuje sběrnici Ultra DMA s přenosovými rychlostmi 100/66
MB/s.
Integrovaný vstup/výstup
Základní deska je vybavena kompletní sadou vstupních portů a konektorů I/O:
•
•
•
•
•
•
Dva porty PS/2 pro myš a klávesnici
Jeden sériový port
Jeden paralelní port
Čtyři porty USB
Jeden port LAN (volitelně)
Zvukové konektory pro mikrofon, zvukový vstup a 8kanálový Hi-Fi zvukový
výstup
Česky
Firmware BIOS
Základní deska využívá BIOS formy AMI, který uživateli umožňuje nakonfigurovat mnoho
systémových parametrů, včetně následujících:
•
•
•
•
Řízení spotřeby
Alarmy při spouštění systému
Parametry CPU
Časování CPU a paměti
Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence
procesoru.
Některé technické parametry hardware a software se mohou měnit bez
předchozího upozornění.
Multi-Language Translation
Caracteristici
Procesorul
915PL-A2 utilizează Pentium 4 de tipul LGA775, având următoarele caracteristici:
•
Funcţionează cu procesoare Intel P4/ Celeron
•
Funcţionează cu bus sistem (FSB) de 800/533 MHz
•
Este compatibilă cu unităţi centrale dotate cu tehnologia „Hyper-Threading”
Tehnologia „Hyper-Threading” permite sistemului de operare să funcţioneze ca şi cum ar
exista două procesoare, putând fi rulate în paralel două fire, fiecare pe câte un procesor „logic”
separat, aflate pe acelaşi procesor fizic.
Setul de chipuri
Seturile de chipuri 915PL Northbridge (NB) şi ICH6 Southbridge (SB) se bazează pe o
arhitectură inovatoare şi scalabilă, care s-a impus deja prin fiabilitate şi performanţă.
915PL (NB)
•
•
•
•
Sprijină adresarea host bus (bus gazdă) de 32 biţi, permiţând unităţii centrale
să acceseze întreaga cantitate de memorie de 4 GB.
Dispune de o coadă de aşteptare cu adâncimea 12 pentru a
sprijini maxim douăsprezece cereri de adresare paralele pe
busul gazdei.
Sprijină PCI Express de 16x pentru interfaţa grafică, este pe
deplin compatibil cu versiunea 1.0a a specificaţiei de bază PCI
Express.
Este compatibil cu tehnologiile de 256-Mb, 512-Mb şi 1-Gb
DDR, pentru unităţi de viteza 8x sau 16x
ICH6 (SB)
•
•
•
•
•
•
•
•
Controler DMA îmbunătăţit, controler de întreruperi şi funcţii de
temporizare
Compatibil cu specificaţia de bază PCI Express, versiunea 1.0a
Compatibil cu specificaţia PCI 2.3
Compatibil cu specificaţie Serial ATA 1.0a
Controler gazdă USB 2.0 integrat, care suportă cel mult opt
porturi USB 2.0
Controler LAN integrat
Compatibil cu specificaţie Azalia, suportând 8 canale audio de
ieşire
Controler IDE integrat, suportând Ultra ATA100/66/33
Memoria
•
•
•
Funcţionează cu module SDRAM DIMM DDR 400/333 MHz DDR
Poate funcţiona cu două module DIMM fără zonă tampon
Poate funcţiona cu module DIMM de cel mult 1 GB, iar cantitatea maximă de
memorie este de 2 GB
Multi-Language Translation
Română
Setul de chipuri 915PL funcţionează doar cu tehnologiile DDR de 256-Mb, 512Mb şi 1-Gb pentru unităţi de viteza 8x sau 16x. NU suportă tehnologia DDR de
128-Mb. Adică, NU suportă modulele de memorie cu faţă dublă de 256 MB şi
cele cu faţă simplă de 128 MB.
Onboard LAN (opţional)
Onboard LAN are următoarele caracteristici:
•
•
•
•
Audio
•
•
•
•
Suportă operaţii de autonegociere N-way de 100/10 Mb/s
Compatibil cu PCI Revision 2.2
Suportă controlul proceselor de duplex total (IEEE 802.3x)
sursă 2.5/3.3 V cu I/O tolerant a 5V
Compatibil cu specificaţia AC’97 2.3
Corespunde cerinţelor de performanţă audio pentru sisteme PC99/2001
Convertoare DA cu 8 canale cu rata de 48khz
Corespunde cerinţelor audio Microsoft WHQL/WLP 2.0
Opţiuni de extindere
Placa de bază este dotată următoarele posibilităţi de extindere:
•
Două sloturi PCI Express de 16x pentru interfaţa grafică
•
Un PCI Express x1
•
Trei sloturi de 32 biţi compatibile PCI, versiunea 2.3
•
O interfaţă IDE 40 cu profil plat care poate deservi două unităţi IDE
•
O interfaţă pentru unitate floppy
•
Patru conectoare SATA cu 7 ace
Placa de bază 915PL-A2 suportă bus mastering UltraDMA cu viteze de transfer de
100/66 MB/s
I/O integrată
Placa de bază este dotată cu un set complet de porturi şi conectoare I/O:
•
•
•
•
•
•
Două porturi PS/2, pentru mouse şi tastatură
Un port serial
Un port paralel
Patru porturi USB
Un port LAN (opţional)
Mufe audio pentru microfon, intrare audio şi pentru 8 canale audio de ieşire de
înaltă fidelitate
Română
Firmware BIOS
Placa de bază utilizează AMI BIOS, care permite utilizatorului să configureze mai mulţi
parametri ai sistemului, cum ar fi:
•
•
•
•
Gestionarea energiei
Alarme de trezire
Parametri CPU
Temporizare CPU şi memorie
Acest firmware poate fi utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă ale
procesorului.
Anumite specificaţii hardware şi elemente de software pot fi modificate fără
înştiinţare prealabilă.
Multi-Language Translation
Спецификация
Процесор
Дънната платка 915PL-A2 поддържа Pentium 4 тип LGA775 със следните
спецификации:
•
Поддръжка на процесори Intel P4/Celeron
•
поддръжка на системна шина със скорост 800/533MHz
•
поддръжка на процесори с технология “Hyper-Threading"
Технологията “Hyper-Threading" позволява да се “излъже” операционната система, че
работи на два процесора, което дава възможност за паралелното изпълнение на две
задачи на два отделни “логически” процесора в един и същ физически процесор.
Чипсет
Чипсетът със северен мост 915PL (NB) и южен мост ICH6 (SB) е изграден на базата
на оригинална архитектура с възможност за надстройка с доказана надеждност и
производителност.
•
32-bit адресация на шината, което позволява на процесора
915PL (NB)
достъп към пълното адресно пространство на паметта 4GB.
•
12-deep In-Order Queue (12-стъпков конвейерен буфер) с
поддръжка на до дванадесет операции за четене на данни от
паметта.
•
поддръжка на шина PCI Express x16 за графичен интерфейс,
напълно съвместима с шината PCI Express Base ревизия
1.0a.
•
поддръжка на технологии 256-Mb, 512-Mb и 1-Gb DDR за x8
и x16 устройства
ICH6 (SB)
•
•
•
•
•
•
•
•
Памет
•
•
•
подобрен DMA Контролер, контролер на прекъсванията и
часовник
поддръжка на шината PCI Express Base, ревизия 1.0a
поддръжка на шината PCI 2.3
съвместимост със спецификацията Serial ATA 1.0a
интегриран контролер USB 2.0 с поддръжка на до осем
порта USB 2.0
интегриран мрежов контролер
съвместимост със спецификацията Azalia с поддръжка на 8канално аудио
интегриран контролер IDE с поддръжка на Ultra ATA100/66/
33
поддръжка на DDR 400/333 MHz DDR SDRAM DIMMs
поддръжка на до два небуферирани DIMM слота
до 1 GB памет на 1 DIMM канал с максимален капацитет 2 GB
Multi-Language Translation
Български
Чипсетът 915PL поддържа само технологиите 256-Mb, 512-Mb and 1-Gb
DDR за x8 и x16 устройства, и НЕ поддържа технологията 128-Mb DDR.
Това означава, че НЕ могат да се подключат модули 256 MB Double Side
Memory Module и 128 MB Single Side Memory Module.
Интегриран мрежов контролер (опция)
Спецификация на интегрирания мрежов контролер:
•
поддръжка на 100/10 Mb/s, N-Way Auto-negotiation operation
•
Съвместимост със спецификацията PCI 2.2
•
поддръжка на Full Duplex Flow Control (IEEE 802.3x)
•
Захранване 2.5/3.3V с толеранс 5V
Аудио
•
•
•
•
Съвместимост със спецификацията AC’97 2.3
Съответствие с изискванията за аудио производителност на системи
PC99/2001
Осем-канални цифрово-аналогови преобразователи / 48KHz
аудио - съвместимо с спецификацията Microsoft SHQL/WLP 2.0
Възможности за разширяване
Дънната платка има следните разширителни възможности:
•
два слота PCI Express x16 за графичен интерфейс
•
един слот PCI Express x1
•
три слота 32-bit PCI v2.3
•
един нископрофилен 40-pin IDE колектор с поддръжка на две IDE устройства
•
един конектор за флопидисково устройство
•
четири конектора 7-pin SATA
Дънната платка 915PL-A2 поддържа шина UltraDMA 100/66 MB/s
Интегриран Вход/Изход контролер
Дънната платка има пълен набор от I/O портове и конектори:
•
два PS/2 порта за мишка и клавиатура
•
Един сериен порт
•
Един паралелен порт
•
Четири USB порта
•
Един LAN порт (опция)
•
аудио жак за микрофон (вход), линеен вход, линеен изход и изход за 8-канално
High Definition аудио
BIOS Firmware
Български
Дънната платка използва AMI BIOS с възможност за различни системни настройки,
включително
•
управление на захранването
•
Wake-up аларми
•
параметри на процесора
•
синхронизиране на процесора и паметта
настройка на скоростта на часовника на процесора
Хардуерните и софтуерни спецификации и параметри могат да бъдат
изменени без предупреждение.
Multi-Language Translation
Jellemző
Processzor
A 915PL-A2 LGA775 típusú Pentium 4 számára készült, és a következő jellemzőkkel bír:
•
•
•
Intel P4/Celeron processzorokkal működik
800/533 MHz sebességű rendszerbuszt (FSB) támogat
Támogatja a „Hyper-Threading” technológiát használó központi egységeket
A „Hyper-Threading” technológia által az operációs rendszer úgy működik, mintha két
processzorral rendelkezne, ami két szál párhuzamos futását teszi lehetővé két független,
ugyanazon fizikai processzoron található „logikai” processzoron.
Lapkakészlet
A 915PL Northbridge (NB) és ICH6 Southbridge (SB) lapkakészletek egy új és méretezhető,
nagy megbízhatóságú és teljesítőképességű architektúrára épülnek.
915PL(NB)
•
•
•
•
32 bites host bus addressing-et (gazdabusz címzést) tesz
lehetővé, ami által a központi egység a teljes 4 GB-os címzési
tárhelyhez hozzáfér.
12-es mélységű sorbanállással rendelkezik, amellyel akár
12 megoldatlan csővezetékes címzési kérést képes kezelni a
gazdabuszon.
Egy 16-szoros Express PCI-vel rendelkezik a grafikus
interfész számára, amely teljesen kompatibilis a PCI Express
alapspecifikáció 1.0a változatával.
256 Mb-os, 512 Mb-os és 1 Gb-os DDR technológiát támogat 8és 16-szoros eszközök esetében
A 915PL lapkakészlet csak a 256 Mb-os, 512 Mb-os és 1 Gb-os DDR technológiákat
támogatja 8- és 16-szoros eszközök esetében, azaz a 128 Mb-os technológiával NEM
kompatibilis. Azaz NEM működik 256 MB-os kétoldalú, illetve 128 MB-os egyoldalú
memóriaegységekkel.
ICH6 (SB)
•
•
•
•
•
•
•
•
Memória
Magyar
•
•
•
Fejlett DMA vezérlő, megszakításvezérlő és időzítő funkciók
Kompatibilis a PCI Express alapspecifikáció 1.0a változatával
Kompatibilis a PCI 2.3-as specifikációjával
Kompatibilis a soros ATA 1.0a specifikációval
Beépített USB 2.0 gazda vezérlő, legtöbb nyolc USB 2.0 portot
támogat
Beépített LAN vezérlő
Kompatibilis az Azalia specifikációval, 8 csatornás audio
kimenetet támogatva
Beépített IDE vezérlő, amely az Ultra ATA100/66/33 technológiát
támogatja
400/333 MHz-es DDR SDRAM DIMM egységekkel működik
Két puffermentes DIMM egységgel működik
Maximum 1 GB-os DIMM egységeket támogat, maximális memória 2 GB
Multi-Language Translation
Alaplapon levő LAN (választható)
Az alaplapon levő LAN jellemzői:
•
100/10 Mb/s N-Way automatikus beállítással
•
PCI Revision 2.2 –vel kompatibilis
•
Támogatja a teljes duplex folyamatvezérlést (IEEE 802.3x)
•
2.5/3.3 V áramforrás 5V toleráns I/O-tal
Audio
•
•
•
•
Megfelel az AC’97 2.3-as specifikációnak
Megfelel a PC99/2001 rendszerek audio-teljesítménnyel szembeni követelményeknek
8 csatornás DA konvertor 48khz-es sebességgel
Megfelel a Microsoft WHQL/WLP 2.0 audio követelményeine
Bővítési lehetőségek
Az alaplap a következő bővítési lehetőségekkel rendelkezik:
•
Két 16-szoros PCI Express a grafikus interfész számára
•
Egy 1-szeres PCI Express foglalat
•
Három 32 bites, a PCI 2.3-as változatával kompatibilis foglalat
•
Egy 40 tűs lapos IDE foglalat, amely két IDE eszközt képes kiszolgálni
•
Egy hajlékonylemez meghajtó interfész
•
Négy 7 tűs SATA csatlakozó
A 915PL-A2 alaplap támogatja az UltraDMA bus mastering megoldást, 100/66 MB/s ebességen
Beépített I/O
Az alaplapot az I/O portok és csatlakozók teljes készletével szerelték fel:
•
Két PS/2 port az egér és a billentyűzet számára
•
Egy soros port
•
Egy párhuzamos port
•
Egy LAN port (opcionális)
•
Négy USB port
•
Csatlakozók mikrofon bemenethez, audio bemenethez és 8 csatornás, nagy hűségű
audio kimenethez
BIOS Firmware
•
•
•
•
Energiagazdálkodás
Ébresztési riasztások
CPU paraméterek
CPU és memória időzítés
A firmware segítségével a processzor órajel-frekvenciáinak paramétereit is beállíthatják.
Bizonyos hardverjellemzők és szoftverelemek előzetes bejelentés nélkül
módosulhatnak.
Multi-Language Translation
Magyar
Az alaplapon levő AMI BIOS segítségével a felhasználó a rendszer sok paraméterét állíthatja be,
például:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement