User Manual Motion Detector Infra Garde 200 UP Acoustic

User Manual Motion Detector Infra Garde 200 UP Acoustic
User Manual Motion Detector Infra Garde 200 UP Acoustic
Warning!
- Any work on the main power supply must only be completed by trained
specialists.
- The product must be installed in accordance with installation guidelines/standards specific to your country.
- Disconnect the 230V power supply before starting the installation
process.
- The device’s power supply must always be fitted with a (250VAC, 10A)
type C fuse in accordance with EN60898-1.
- The device must not be installed on conductive surfaces.
- The device is suitable for indoor installation only.
- Disconnect power prior to replacing a lamp.
- Faulty lamps may cause a short-circuit and thereby permanently damage
the device.
- To ensure the operational reliability of the detector, keep a minimal
distance of 1m to lamps installed on the same height level.
- Lamps installed underneath the detector or in the detection area may
impair functionality. Keep away from heating devices.
- In case of malfunction, such as continuous lighting, or false triggering
please refer to the troubleshooting section on this page.
Connection of electrical loads
High inrush currents will considerably shorten the lifetime of the detector’s
in-built relay. Please verify the technical data provided by the lamp or luminaires manufacturer concerning inrush currents, specifically with compact
fluorescent, fluorescent lamps, electronic ballast, etc. in order not to overload the internal relay. We recommend connecting a maximum of three to
four motion detectors in parallel. If the number of switching cycles is above
average or in the event of increased (inductive) loads, we recommend using
the short pulse function on the motion detector and switching the load via
an external staircase timer switch or contactor.
Detection Range
frontal detection
NOT SENSITIVE
detection range =
approx. -50%
Function
The detector reacts to the motion of heat (positive or negative in relation to
the environment). If a person approaches the monitored area, the device
will turn on the connected light automatically. If the person leaves the area,
the light will be switched off after the preset duration (short impulse, 30 sec.
to 20 min.). The in-built microphone extends the delay time while lights are
still on as well as during a maximum 10 seconds after lights switch off.
The connected light will be turned on only when the ambient light value is
below the adjusted value.
Installation
Install device at regular light switch height between 100 and 150 cm.
tangential detection
= SENSITIVE
The detection range depends on the installation height and walking direction
(high sensitivity when cutting or changing a switching segment). Since the
detector reacts to temperature differences between heat source and
ambient temperature, the response may vary depending on the installation
site (floor heating, hot environment, etc.).
Manual switch
Wire the detector as follows:
phase / outer conductor (L) brown;
neutral-/ neutral conductor (N) blue;
switching output / switched phase/ outer conductor L↑.
Optional: remote switching (S) through impulse switch (without pilot lamp),
phase to terminal S. Keep wire as short as possible. Capacitive current at
terminal S may cause malfunctions.
Special function: 2x impulse at terminal S within 2 sec. = 6 h of permanent
light, followed by AUTO operation. 1x impulse during permanent light
returns device to AUTO operation.
OFF
LUX (twilight sensor)
Controls light value from which motion detection triggers lights on. Moon
symbol = activation at night; sun symbol = activation during daytime. TEST
= detection area check with short delay time.
Technical Data
Nominal power:
Switching power:
Time adjustment:
Microphone:
230V/50Hz
max. 1000W / 5A (cos φ = 1)
max. 250VA / 1.25A inductive
impulse, 30 s to 20 min.
adjustable 45~70 dB
Twilight switch:
Detection area:
Dimensions:
IP protection:
ON
As with a regular light switch, the light may be switched OFF (left) or ON
(right) permanently. The middle position will switch lighting automatically.
Troubleshooting
error
light does not turn on:
cause/amendment
- twilight adjustment value set too high
- check light fitting and lamp
- check mains power / fuses
detector triggers without
reason/light never turns off:
- check detection area for errors: draught,
animals, heating may cause faulty switching!
- check distances to lamps (heat reflection or
direct light influence)
- check vicinity for background noise and adjust microphone sensitivity
- connect RC element in parallel to transformers, relays, electric ballast
turns the light on during
daytime:
- twilight adjustment set too low
TIME
Set up delay time for lights on time period after last movement detection.
Choose between impulse function for staircase switches, 30s, 1m, 3m, 5m,
10m, 20m.
VOICE (microphone)
Activate in-built microphone to extend delay time during lights on without
additional movement detection or visual contact (max. 10 seconds after
lights switch off). Each detected noise re-triggers set delay time. Middle
position detects normal talking volume; maximum setting detects whispers.
AUTO
Electronic Control
Induction in long installation wires (if several detectors connected in parallel) may
generate a considerable capacitive current on the switched phase. For electric
loads using only a small control current, such as staircase timer switches, this
may lead to permanent switching or general malfunctions. In order to minimise
the capacitive current, an RC element may be connected in parallel to the load.
Alternatively, a contactor, which is more tolerant to capacitive currents, may be
installed before the load. We recommend a maximum of four detectors
connected in parallel.
Do not dispose of electrical appliances in your waste bin, use the collecting point
approx.
5-1000
Lux
of your
municipality,
or return the old device to your dealer.
180° / 8 m frontal, 5 m lateral
80 x 80 x 30 mm (visible)
IP20 indoors / class II
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising