American Trails 355-41 Kitchen Breakfast Cart Instructions

Assembly Instruction

Item# 355-4X

Breakfast Cart with Drop-Leaf Table

American Maple Top, Square

Before You Begin

Check to make sure you have the following:

Page 2/8

FOR CART

F

G

B

D

FOR DRAWERS

I

H

K

E

C

J

I

A

B

G F

G

D

E

Part

A

B

C

Description

Drop-Leaf Table Top

Side Panels

Middle Panel

Bottom Panel

Cross Supports

Leaf Support

Towel Bars

1

2

1

2

Q’ty

1

2

1

RF10003

JCA 1/4" x 32 x 16

RF10019

F6 x 1" x 4 x 16

RF10004

F6 x 5/8" x 8

RF40001

Wood Plug x 1

RF40091

Dowel Caster Lock

RF40092

Caster Lock x 2

RF40093

Caster Free x 2 x 1

RF40103

Allen Key

Part

H

J

I

K

Description

Front Panels

Side Panels

Back Panels

Bottom Panels

RF10019

F6 x 1" x 16

RF40170

Knob x 2 x 4

WD40096

Dowel Stoppers

Q’ty

2

4

2

2

FOR STOOL

M

L

O

N

Part

L

M

N

O

Description

Side Panels

Seats

Round Strip (Long)

Round Strip (Short)

Q’ty

4

2

4

4

RF10003

JCA 1/4" x 32 x 16 x 16

RF40001

Wood Plug

Page 3/8

C

Diagram 1.

D x 2

RF10003

Step 1:

Attach the middle panel (C) to the bottom panel (D) with 2 (RF10003) screws as seen in Diagram 1.

B

C

B

D

Diagram 2.

x 4

Step 2:

Attach side panels (B) to the bottom panel (D) with 4 (RF10003) screws as shown in Diagram 2.

RF10003

B

Page 4/8

E

E x 6

RF10003

C

B x 8

WD40001

Step 3:

Attach cross supports (E) into the unit by using 6 (RF10003) screws and cover the screws with the wood plugs

(WD40001) as shown in Diagram 3.

Diagram 3.

x 4

RF10003

Step 4:

Attach the towel bars (G) to the left and right panels (B) with 4 (RF10003) screws as seen in Diagram 4.

G

B

C

B

Diagram 4.

G

F

C

B

D

Diagram 5.

Step 5:

Align the hinges of the leaf support (F) to the middle panel (C), as shown in Diagram 5.

D

B

F

C

B x 4

RF10019

A Diagram 6.

Step 6:

Invert the drop-leaf table top (A) on a soft surface to prevent scratching.

Align the screw holes of both the top frame and the drop-leaf top and secure them with 4 (RF10019) screws, as shown in Diagram 6.

Page 5/8

B

F

C

D

B x 16

RF10004

Page 6/8

Diagram 7.

Step 7:

Attach 2 caster locks (RF40092), 2 caster frees (RF40093) to the bottom panel (D) with 16 (RF10004) screws and insert the dowel caster lock (RF40091) into the hole of the leaf support (F) as seen in Diagram 7.

FOLD LEAF

Page 7/8 x 8

RF10019

J I

K

I H

Diagram 8.

x 1

RF40170

Step 8:

Assemble the drawers by attaching the sides (I), back (J), and bottom (K) to the front panel (H) by using 8 (RF10019) screws. Attach the handle knob (RF40170) to the front panel (H) as shown in Diagram 8.

x 4

WD40096

Diagram 9.

Step 9:

Align the grooves of the drawers with the wood tracks and slide the drawer in.

Insert the drawer stopper (WD40096) into the holes of both sides of the drawer as shown in Diagram 9.

Page 8/8 x 8

RF10003 N

O

L x 8

WD40001

L

M

Diagram 10.

Step 10:

Lay the seat (M) on the floor and insert one side panel (L).

Insert and fasten short (O) and long (B) round strips using screws (RF10003), as seen in Diagram 10.

CAUTION: DO NOT TIGHTEN SCREWS UNTIL THE UNIT IS FULLY ASSEMBLED.

Attach the other side panel and fasten screws.

Tighten screws by using the Allen Key (RF40103).

Cover all holes with wood plugs (WD40001).

Diagram 11.

To store the bar stools, slide them between the hanging rails.