MultiQ 219, User Guide

1. Cautions and Warnings
Table of Contents
1. Cautions and Warnings................................................ 2
2. FCC Requirements ...................................................... 3
3. Product Safety Precautions ......................................... 4
CAUTION !!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
4. Introduction .................................................................. 5
5. Hardware Installation ................................................... 6
5-1. Unpacking ............................................................. 6
5-2. Installation ............................................................. 6
5-3. Video Input Pin Assignment ................................ 12
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back).
No user serviceable parts inside.
Refer servicing to qualified personnel.
6. Display Timing ........................................................... 14
6-1 Applicable video timing for video input................. 14
7. Monitor Controls......................................................... 15
7-1 Hot-keys ............................................................... 16
7-2 Screen Adjustment Operation Procedure ............ 16
8. Screen Adjustment..................................................... 17
8-1 Main Menu............................................................ 17
8-2 Quick Start............................................................ 18
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MONITOR TO RAIN
OR MOISTURE.
“HIGH VOLTAGE EXISTS ON THE BACK LIGHT POWER LEAD OF THIS MONITOR.
BEFORE SERVICING, DETERMINE THE PRESENCE OF HIGH VOLTAGE BY
8-3 Auto Adjust ........................................................... 18
CONNECTING THE H.V. METER BETWEEN THE BACK LIGHT POWER LEAD AND
8-4 Video Input Sources............................................. 19
CHASSIS ONLY.“
8-5 OSD Adjusting and Controls ................................ 20
9. Troubleshooting Tips ................................................. 23
10. Specification............................................................. 24
11. Energy Declaration .................................................. 25
12. Appendix .................................................................. 26
For medical model only:
CAUTION: The power adapter use on the LCD monitor products has been evaluated and
tested to comply with special use of medical equipment and certified under
EN60601 and EN55011 standards. To prevent electric shock and fire hazard,
Replaced or installed only with the same power adapter.
< Power adapter: EN60601 Certified, ELJINTEK / MPU50A>
Note: For EN60950 and EN55022, the power adapter switch to FSP/
FSP060-DBAB1 or STARMEN/TCS060120.
To prevent shock, connect the medical monitor to personal computer
that complied with this standard.
WARNING: To prevent overturn when moving, transport the equipment on flat surface only.
Do not put on unstable position.
1 - English
2 - English
2. FCC Requirements
“This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.“
3. Product Safety Precautions
Follow all warnings and instructions marked on the product.
• Do not use this product near water - e.g. near a bathtub, washbasin,
swimming pool, kitchen, laundry tub or in a wet basement.
• This monitor should be installed on a solid horizontal base.
The equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in strict accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measure:
• When cleaning, use only a neutral detergent cleaner with a soft damp cloth.
Do not spray with liquid or aerosol cleaners.
• Do not expose this monitor to direct sunlight or heat. Hot air may cause
damage to the cabinet and other parts.
• Adequate ventilation must be maintained to ensure reliable and continued
operation and to protect the monitor from overheating. Do not block ventilation
slots and openings with objects or install the monitor in a place where ventilation may be hindered.
• Increase the separation between the equipment and the receiver.
• This monitor should be operated from the type of power source indicated on
the AC/DC adapter. Do not install this monitor near a motor or transformer
where strong magnetism is generated. Images on the monitor will become
distorted and the colour irregular.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Do not allow metal pieces or objects of any kind to fall into the monitor through
ventilation holes.
• Consult the dealer or an experienced radio/TV technician for help.
• Do not attempt to service this unit yourself. Removal of the monitor cover may
expose you to dangerous voltage or other risks. Refer all servicing to qualified
service personnel.
• Reorient or relocate the receiving antenna.
Shielded interconnected cables and shield power cords must be employed with
this equipment to insure compliance with the pertinent RFD emission limits
governing this device.
Changes or modifications not expressly approved by the manufacturer could void
the user authority to operate the equipment.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel in the event that:
• Liquid is spilled into the product or the product is exposed to rain or water.
Notice of Compliance with Canadian Interference-causing Equipment Regulations
• The product does not operate normally when the operating instructions are
followed.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
• The product has been dropped or the cabinet has been damaged.
Cet appareil numerique de la Classe B respecte toutes les exigences du Reglement sur le materielle brouilleur du Canada.
3 - English
• The product exhibits a distinct change in performance, indicating a need for
service.
• Power cord or plug is damaged or frayed.
4 - English
4. Introduction
5. Hardware Installation
Welcome to enjoy the fantastic world of LCD-monitors. This new technology will
bring you a whole new feeling for your “monitor”. We show here some of the
major advantages of the LCD monitor. You will most certainly find some other
advantages when you use it.
This chapter will guide you through the correct installation procedures of your
LCD monitor.
• The character of low radiation and less flicker reduce the probability of harm
for your health compared to traditional CRT monitor.
• The LCD monitor’s compact size requires only minimal desktop space. These
two merits make it easy to use in almost any environment and easy to
transport.
• The LCD monitor has a low power consumption and offers savings on power
bills and the earth’s resources.
• The design of the LCD cabinet is both attractive and ergonomic.
• The usage of the LCD monitor is the same as the CRT monitor. There is no
need to change the hardware of your computer, just plug and play.
• Only for POS-model: An option provides VESA standard mounting function
(Conforms to VESA FPMPMI specification).
• The composite video input (AV and S-VIDEO) can accept different signal
source, for example VCR and DVD player. (Only support to Video function
monitor).
5 - English
5-1. Unpacking
After you unpack your LCD Monitor, please make sure that the following items are
included in the carton and in good condition. If you find that any of these items are
damaged or missing, please contact your dealer immediately.
• One LCD Monitor
• AC/DC adapter with 12V DC output
• AC power cord
• VGA cable
• This user manual
5-2. Installation
This LCD monitors DOES NOT require any special drivers. Necessary drivers are
supplied by the graphics card manufacturer and may be found on the
diskettes/CD supplied with the graphics card that came with your computer.
Windows drivers for both the monitor and the graphics card are supplied on the
Windows CD or diskettes. You may use the standard resolution SXGA
(1280x1024@60) as the monitor type. The graphics card must also be set up
correctly in Windows and make sure the video output of the graphics card is listed
in Section 6.1 or check your Graphics card manual or Windows ReadMe file for
further information on Graphics card. After the question listed above is solved, we
continue the setup procedure as per below.
6 - English
5. Hardware Installation
1. Power off both the Computer and Monitor before making any connections.
2. Install Monitor on a solid horizontal surface such as a table or desk.
3. Connect the power cable and the AC/DC adapter, then connect the adapter to
the back of the LCD monitor.
4. The LCD monitor comes with one graphic card cable (D-sub 15-pin or DVI-D
24-pin).
Example:
a) Analog signal (D-sub 15 pin Cable):
Connect the signal cable on the rear of the monitor to the 15-pin
connector on the rear of the computer.
b) Digital signal (DVI-D 24 pin Cable)
Connect one end of the signal cable to the DVI input on the rear of the
monitor; and the other end to the DVI connector on the rear of the
computer. (Only support to DVI-D function monitor)
5. Or connect the composite signal (Video, S-Video) cable from back of the video
equipment to the rear of the monitor. (Only support to video function monitor)
6. Switch on power to the PC system or composite signal device, then the LCD
monitor.
5. Hardware Installation
The following picture provides the connection outline.
1 = Power cord
2 = AC/DC Adapter
3 = 15 pin D-SUB
Earth Protective
(For medical model only)
7 - English
4 = 24 PIN DVI-D
5 = S-VIDEO
6 = COMPOSITE video
(only support to video function model)
8 - English
5. Hardware Installation
5. Hardware Installation
HINGE METAL
VESA BRACKET
1. Please connect all cables to the
back of the monitor before mount
the VESA metal to it.
2. Just mount four screws to the
monitor that indicate as right
picture.
3. Attach the VESA metal on the
screws then fasten them by a screw
driver through the four holes on the
VESA metal.
9 - English
10 - English
5. Hardware Installation
5. Hardware Installation
TABLE MOUNT
5-3. Video Input Pin Assignment
This section describes the pin assignment of the monitor’s video connector. It is
called a 15 Pin Mini D-sub Connector.
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
11 - English
Signal Connector
Red Video Signal
Green Video Signal
Blue Video Signal
N.C.
Ground
Ground for red video signal
Ground for green video signal
Ground for blue video signal
N.C.
Ground
N.C.
DDC data
Horizontal sync signal
Vertical sync signal
DDC clock
12 - English
6. Display Timing
5. Hardware Installation
24 Pin DVI-D Connector. (Only support to DVI-D function monitor)
9
1
8
17
24
6-1 Applicable video timing for video input
The following table lists the supported display quality modes that the LCD monitor
provides. If other video modes are used, the monitor will stop working or display
unsatisfactory picture quality.
MQ219 series model
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal Connector
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. SGND
T.M.D.S. Data4- N.C.
T.M.D.S. Data4+ N.C.
DDC CLK
DDC DAT
A_VSYNC
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. SGND
T.M.D.S. Data3- N.C.
T.M.D.S. Data3+ N.C.
DDC POWER +5 V
GND
Pin No.
16
17
18
19
20
21
22
23
24
Signal Connector
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. SGND
T.M.D.S. Data5- N.C.
T.M.D.S. Data5+ N.C.
T.M.D.S. CLK GND
T.M.D.S. CLK+
T.M.D.S. CLK-
Mode
Resolution
720*400@70 Hz
640*480@60 Hz
VGA
640*480@72 Hz
640*480@75 Hz
800*600@56 Hz
800*600@60 Hz
SVGA
800*600@72 Hz
800*600@75 Hz
1024*768@60 Hz
XGA 1024*768@70 Hz
1024*768@75 Hz
1152*864@75 Hz
1280*1024@60 Hz
SXGA
1280*1024@75 Hz
DOS
EGA
DOS
VGA
XGA
640*350@70 Hz
720*400@70 Hz
640*480@60 Hz
1024*768@72 Hz
640*480@60 Hz
VGA
SVGA 832*624@75 Hz
XGA 1024*768@75 Hz
13 - English
VESA MODES
Nominal
Horizontal
Vertical
Pixel
Nominal
Nominal
Total
Frequency Frequency Clock
(MHz)
+/- 0.5 kHz
+/- 1 Hz
900*449
31.469
70.087
28.322
800*525
31.469
59.940
25.175
832*520
37.861
72.809
31.500
840*500
37.500
75.000
31.500
1024*625
35.156
56.250
36.000
1056*628
37.879
60.017
40.000
1040*666
48.077
72.188
50.000
1056*625
46.875
75.000
49.500
1344*804
48.363
60.004
65.000
1328*806
56.476
70.069
75.000
1312*800
60.023
75.029
78.750
1600*900
67.500
75.000
108.00
1688*1066
63.981
60.020
108.00
1688*1066
79.976
75.025
135.00
IBM MODES
800*449
31.469
70.086
25.175
900*449
31.469
70.087
28.322
800*525
31.469
59.940
25.175
1304*798
57.515
72.1
75.000
MAC MODES
800*525
31.469
59.940
25.175
1152*667
49.725
74.551
57.283
1328*804
60.241
74.927
80.000
14 - English
7. Monitor Controls
7. Monitor Controls
7-1 Hot-keys
Auto Config: Pressing [ - ] and [ + ] simultaneously when the monitor is turned on
starts the Auto Config mode.
Key-Lock function: Push and hold the Select button and then push the [ - ] and
[ + ] buttons simultaneously and hold for one second. The buttons on the monitor
are now locked. To unlock, do the same procedure again.
7-2 Screen Adjustment Operation Procedure
1) Entering the screen adjustment
The setting switches are normally at stand-by. Push the MENU key once to
display the main menu of the screen adjustment. The adjustable items will be
displayed in the main menu.
[ - ] button
Used for the following:
• to scroll counter left in the menu
[ + ] button
Used for the following:
• to scroll right in the menu
• to decrease value of selected item
• to increase value of selected item
• to adjust the contrast on the monitor
(works without showing the menu
system)
• to adjust the brightness on the
monitor (works without showing
the menu system)
SELECT button
To confirm the current selection. It’s also
used for going back to previous menu or
sub-menu, and the changed data will be
saved to memory.
MENU button
Enters or exits the OSD (On Screen
Display) menus. It also exits from the
submenu back to the previous menu.
This type of cancellation will not save
the previous changes.
POWER button
Pressing the power key will turn the
monitor on. Pressing it again will turn
it off.
POWER INDICATOR (green)
The LED will be lit in normal ON state,
and will flash in power saving mode.
15 - English
2) Entering the settings
Use the [+] and [-] keys to select the desired setting icon and push the
[SELECT] key to enter sub-menu.
3) Change the settings
After the sub-menu appears, use the [+] and [-] keys to change the setting
values.
4) Save
After finishing the adjustment, push the [SELECT] key to memorize the setting.
5) Return & Exit the MAIN MENU
To go back to the previous menu or exit the screen adjustment, push the
[MENU] key. When no operation is done for around 60 seconds (default OSD
timeout), it goes back to the stand-by mode and no more switching is accepted
except [MENU] to restart the setting.
16 - English
8. Screen Adjustment
8. Screen Adjustment
8-1 Main Menu
8-2 Quick Start
The OSD (On Screen Display) main menu (Figure 8-1) is displayed on screen
when [MENU] key is pressed. The OSD menu is a combination of graphics and
text display. The first line always shows the current selected or active menu item.
The bottom line of the main menu shows information for the selected function.
Initial Setup
The [+] and [-] keys are used to scroll through items within the menu. The
selected item is highlighted as the scrolling moves along. The [SELECT] key is
used to activate the highlighted item during this state.
Make sure your graphics adapter has the following settings: 1280 x 1024 resolution with refresh rate at 60 Hz (or 75 Hz), In order to obtain the best possible
picture on your new MultiQ Monitor press [ - ] and [ + ] buttons simultaneously for
Auto Configuration. This procedure only has to be done once and the monitor will
remember its optimal settings in the future.
If you are not quite satisfied follow the instructions in chapter 8-3 below.
8-3 Auto Adjust
BRIGHTNESS
MultiQ
MQ219
www.multiq.com
1280 x 1024 60Hz
Figure 8-1. OSD Main Menu
17 - English
The Auto adjust function is intended for use on Macintosh and PCs running
Windows. It may not function properly if any of the following applies:
• PC running MS-DOS (not Windows).
• The background colour for the "wallpaper" or "desktop" pattern is set to black
or dark shades of any colour.
The main menu item "Auto adjust” is used to perform automatic configuration of
the Brightness, Contrast, Vertical & Horizontal Position, Pixel clock frequency,
Video signal amplification and Tune.
1. Enter the Windows Shut-down screen (Press "Start button" and select "Shut
down" to get a "grayed" screen) or open an empty document (white page) in
Microsoft Word or Notepad. Note: The Wallpaper colour CAN NOT be black
or a very dark colour.
2. Enter OSD Main Menu and Chose the "Auto adjust” in the “auto config”, then
press SELECT key. The Picture will auto-adjust by itself. After 4 seconds, you can exit
OSD and SHUT DOWN frame.
3. If you are still not satisfied with the picture quality, you could choose
CONTRAST in the OSD Main Menu and adjust it. You can also manually
adjust PHASE, CLOCK, etc. in the OSD.
18 - English
8. Screen Adjustment
8. Screen Adjustment
8-4 Video Input Sources
8-5 OSD Adjusting and Controls
(Only support to DVI-D, AV or S-VIDEO function monitor.)
z
The following table shows the OSD functions that are supported by different video
input sources.
Please make sure which video source you are using, then select the correct functions in the OSD display. Not available selections will be grayed out.
Analog
Digital
AV/S-VIDEO
OSD ITEM
BRIGHTNESS
CONTRAST
AUTO CONFIG
H-POSITION
V-POSITION
CLOCK
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
AVAILABLE
AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
PHASE
AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
AVAILABLE
NOT AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
AVAILABLE
INFORMATION
SHARPNESS
COLOR
OSD MENU
INPUT
RESET
HUE
SATURATION
Setup the brightness of the panel.
z
CONTRAST
The Contrast menu item is used to adjust image contrast.
z
VIDEO INPUT
BRIGHTNESS
AUTO CONFIG
There are two items: AUTO ADJUST and AUTO COLOR . Use the Adjust [+] and [ - ]
key to scroll up and down in menu, then press the SELECT key to start this function. If
the MENU key is pressed, the main menu is re-displayed and nothing is changed.
AUTO ADJUST: Used to perform automatic configuration of the phase、clock、
vertical and horizontal positioning.
AUTO COLOR: It is used to adjust the gain and offset of the Red, Green and Blue
channels on the ADC automatically.
z
H-POSITION
H-Position is used to adjust the horizontal image position manually. A slider
with current value is displayed.
z
V-POSITION
V-Position is used to adjust the vertical image position manually. A slider with
current value is displayed.
z
CLOCK
Reduce vertical stripes in the screen image.
z
PHASE
Reduce horizontal stripes in the screen image.
z
SHARPNESS
This can adjust the video quality to be sharp or blur (special for text mode).
19 - English
20 - English
8. The Screen Adjustment
z
8. The Screen Adjustment
z
INFORMATION
The “INFORMATION” menu provides the user with detailed information regarding the
current input format and version (include resolution, vertical /horizontal frequency, pixel
clock and software version).
z
There are five items: LANGUAGE, OSD H POSITION, OSD V POSITION, OSD
BLENDING and OSD TIME OUT.
LANGUAGE : The item “ LANGUAGE” is use to select the OSD menu in 4
languages. English, Germany, French, or Swedish are available.
OSD H POSITION : The item "OSD H Position” is used to setup the OSD menu H
position.
OSD V POSITION : The item "OSD V Position” is used to setup the OSD menu H
position.
OSD BLENDING : To adjust the blending of the OSD MENU.
OSD TIME OUT : “OSD Time out” is used to set the timeout of the OSD menu.
There are three options for the automatic timeout: 20, 40 and 60 seconds.
COLOR
Configure the image color. There are three items : 9300K、6500K、USER.
9300K : The item “9300K” is used to default 9300K color temperature.
6500K : The item “6500K” is used to default 6500K color temperature.
USER:
RGB ADJUST :
-RED: The item “RED” is used to adjust the gain of red channel in ADC.
-GREEN: The item “GREEN” is used to adjust the gain of green channel in
ADC.
-BLUE: The item “BLUE” is used to adjust the gain of blue channel in ADC.
Composite mode: (Video/S-VHS input monitor only)
HUE: Adjustment HUE to make color more green or purples.
SATURATION: Adjustment of colors.
21 - English
OSD MENU
z
MISC MENU
There are three items: INPUT SELECT, AUDIO and RESET.
INPUT SELECT: This is selecting the applicable input source: Analog, Digital, SVIDEO and AV. (Only support to DVI-D, AV or S-VIDEO function monitor.)
ANALOG: signal from PC system graphics card.
DIGITAL: signal from PC system graphics card. (Only support to DVI-D,
function monitor.)
AV, S-VIDEO: Composite video signal AV, S-VIDEO selection. (Only support
to VIDEO function monitor.)
AUDIO: This is used to adjust the sound volume. (Only support to Audio
function monitor.)
RESET: Press “Reset” to return the monitor to its factory default settings.
22 - English
9. Troubleshooting Tips
In the event that you experience trouble with your Monitor, check the following
items before contacting the dealer from whom the Monitor was purchased. The
most common problems usually involve an incorrect connection from the Graphics card to the Monitor. We recommend that you also consult your Graphics card
User's manual during the Troubleshooting Procedure. Do not exceed the maximum refresh rate recommended for the monitor.
Problem
No image on monitor screen?
Keys do not work
properly?
Abnormal image.
Colours of image
on screen are
abnormal
Disturbances on
Screen
Troubleshooting Tip
1. Check that power cord of the Computer or AV device
has been plugged securely into wall outlet.
2. Check that power switch of the Monitor has been
pressed and LED on the front of the Monitor is lit.
3. Check that Video (Signal) Cable from the Monitor
has been securely and correctly connected.
4. Check that Graphics card is firmly seated in card slot
of Computer motherboard.
5. Check that the video input from the Graphics card
falls within the timing range (listed in the table of
section 6) of the Monitor.
1. Check whether the” key-lock” function is enabled or
disabled.
1. Check that the video input from the Graphics card
falls within the timing range (listed in the table of
section 6 ) of the Monitor.
2. Check that Video (Signal) Cable from the Monitor
has been securely and correctly connected to the
Video Connector at the rear side of the Computer.
1. Check that Video Cable from the displays has been
securely and correctly connected to the 15-pin Video
Connector at the rear side of the computer or AV
device.
1. OSD adjustment is incorrect. Please consult section
7 for OSD screen adjustment procedures.
2. Press [ - ] and [ + ] buttons simultaneously to start an
Auto Configuration.
10. Specification
LCD panel type
Resolution
Pixel dimension
LCD monitor colour
OSD control
Manual control keys
Viewing angle
Tilt
Contrast ratio
Brightness
Response time
Active display area
AC/DC adapter
Monitor rating
Input signal
Input connector
Power management
Regulation
Dimensions
Weight (Net)
Accessory
Temperature
Transport & Storage
Plug & Play
23 - English
MQ219 series model
19.0”
SXGA 1280 x 1024 max.
0.294 mm (H) x 0.294 mm (V)
16.2M max.
Brightness, Contrast, Auto Config, H- Position,
V-Position, Clock, Phase, Information, Sharpness, Color, OSD
Menu, MISC Menu
[-], [+], [Power], [Select], [Menu]
H: + 89° ~ -89°. V: +89 ~ -89 °. (Typ.)
With Stand: +70°, 0°.
1300:1 Typ.
2
300 cd/m Typ.
8 ms GTG (Typ.). 20ms (Typ. on/off)
376.32 mm (H) x 301.056 mm (V)
Input: AC 100 ~ 240 V, 50 / 60 Hz
Output: +12 V DC
12Vdc, 4A
Video: Analog 0.7 Vp-p. 1. Video Analog RGB 0.7Vp-p, 75
75 ohms. Sync: TTL Level,
ohms Sync. TTL Level, Positive /
Positive/Negative,
Negative, separate Sync.
Separate Sync
2. DVI: REV1.0 Digital: Single
T.M.D.S.
3. AV/S-VIDEO: 1Vp-p.
(0.7Vvideo+0.3Vsync.), 75 Ohms.
15 Pin D-Sub, 24 Pin DVI-D, VIDEO,
15 Pin D-Sub., DC-IN
S-VIDEO, DC-IN
VESA DPMS Compatible
Energy Star
Safety: UL / GS / ERGO / ISO 13406-2
EMI: CE / FCC
Medical EN60601/ EN55011 (option)
Stand: 428 (W) x 396 (H) × 129 (D) mm
VESA: 428 (W) x 359 (H) x 56 (D) mm
Stand: 10.5 kg
VESA: 9.5 kg
AC/DC adapter, power cord, VGA cable.
Medical: ground wire (option)
Touch: Serial or USB cable (option)
Operation: 0 ~ 40 °C
Ambient Temperature: -10 ~ 60 °C
Humidity Range: 10 ~ 100 %
Atmospheric Pressure: 500hPa ~ 1060hPa
DDC2B
24 - English
12. Appendix
11. Energy Declaration
This monitor is equipped with a function for saving energy, which supports the
VESA Monitor Management Signalling (DPMS) standard. This means that the
monitor must be connected to a computer that supports the VESA DPMS to fulfil
the requirements in the NUTEK specification 803299/94/96. Time settings are
adjusted from the system unit by software. From indicated inactivity to Power
Saving Position A2 the total time must not be set to more than 70 minutes.
NUTEK
VESA state
LED indicator
Power
consumption
Normal operation
On
Green
40W
Power Saving
Position A1
Suspend
Green Flashing
≦ 2W
Power Saving
Position A2
Off
Green Flashing
≦ 1W
We recommend to switch off the monitor when it is not in use for quite a long
time.
• Safety Guidelines
Warning:
This device must be operated with the original power supply, part
number: FSP/ FSP060-DBAB1 or STARMEN/TCS060120.
<For medical model only: ELJINTEK / MPU50A >
CAUTION:
The socket-outlet should be installed near the equipment and
should be easily accessible.
CAUTION:
Use a power cable that is properly grounded. Always use the
appropriate AC cord that is certified for the individual country.
Some examples are listed below:
USA………...UL
Switzerland…….SEV
Canada……..CSA Britain…………..BASE/BS
Germany……VDE Japan…….Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord set for this unit has been enclosed and been selected according
to the country of destination and must be used to prevent electric shock. Use the
following guidelines if it is necessary to replace the original cord set, or if the cord
set is not enclosed. The female receptacle of the cord set must meet IEC-60320
requirements and may look like (Figure A1 below):
FOR THE UNITED STATES AND CANADA
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2),
UL Listed, and CSA Labelled. For units that are mounted on a desk or table, type
SVT or SJT cord sets may be used. Any equipment standing on the floor, only
SJT type cord sets may be used. The cord set must be selected according to the
current rating for your unit. Please consult the table below for the selection criteria
for power cords used in the United States and Canada.
Code Type Size of Conductors in Cord
18 AWG
SJT
16 AWG
14 AWG
18 AWG
SVT
17 AWG
25 - English
Maximum Current Rating of Unit
10 Amps
12 Amps
12 Amps
10 Amps
12 Amps
26 - English
12. Appendix
FOR EUROPEAN COUNTRIES
In Europe you must use a cord set which is appropriate for the receptacles in your
country. The cord set is HAR-Certified, and a special mark that will appear on the
outer sheath, or on the insulation of one of the inner conductors.
12. Appendix
FOR medical model only:
Safety Instructions
Type of protection (electrical): Class III equipment
Explanation of symbols
AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM
Alternating current
For your safety please read the following text carefully.
• If the fitted moulded plug is unsuitable for the socket outlet then the plug
should be cut off and disposed of safely.
• There is a danger of severe electrical shock if the cut off plug is inserted into
an appropriate socket.
• If a new plug is to be fitted, please observe the wiring code as shown below.
• If in any doubt, please consult a qualified electrician.
Direct current
Protective earth (ground)
Attention, consult ACCOMPANYING DOCUMENTS
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the
following code:
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
If the coloured wires of the mains lead of this appliance do not correspond to the
coloured markings identifying the terminals in your plug, proceed as follows:
Dangerous voltage
Disposal
The lamp in this product contains mercury. For disposal, return to MultiQ or
follow local governing ordinances or hospital procedure.
Cleaning
The wire which is coloured GREEN-AND-YELLOW must be connected to the
terminal in the plug which is marked by the letter E or by the Earth symbol or
coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE
must be connected to the terminal in the plug which is marked with the letter N or
coloured BLACK. The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured RED.
If you have any questions concerning which proper power cord to use, please
consult with the dealer from whom you have purchased the product.
CE Conformity for Europe
The device complies with the requirements of the ECC directive 89/336/EEC as amended by 92/31/EEC and 93/68/EEC
Art.5 with regard to "Electromagnetic compatibility", and
73/23/EEC as amended by 93/68/EEC Art.13 with regard to
"Safety".
27 - English
z
z
MAKE SURE THE LCD DISPLAY IS TURNED OFF.
NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN
OR CASE.
To clean the screen:
1. Wipe the screen with a clean, soft, line-free cloth. This removes dust and
other particles.
2. If still not clear, apply a small amount of non-ammonia, non-alcohol based
glass cleaner onto a clean, soft, line-free cloth, and wipe then screen.
To clean the case:
1. Use a soft, dry cloth.
2. If still not clean, apply a small amount of a non-ammonia, non-alcohol based,
mild non-abrasive detergent onto a clean, soft, line-free cloth, and wipe the
surface.
28 - English
Download PDF