Configure start up wizard
Select the screen resolution from the drop-down menu
based on your TV/monitor's resolution.
What is in the box?
O) LaVie
Resolution
Е Netowrk Video Recorder NVR Power Cable q
System Resolution: 1024 * 768/60HZ High Definition IP Cameras Utility Disc Innovation That Secures
Pre-made Cat5e Cables
Remote Control
Quick Start Guide
Warranty Card
Check this box if you wish to see this wizard again after you Mouse Security Stickers
reboot your system.
ВЕ = == «=
= Start wizard when device starts?
We strongly recommend that you change the default
Admin password ‘12345’ for better security protection.
Wizard
Admin Password FREER
New Admin Password
New Password
Confirm
Select the applicable time zone, date/time format, and time.
Wizard
@ Power LED Indicates if the NVR is powered on
& Status LED Indicates if the Hard Drive is working
© VGA Port Connects to TV or computer monitor
© Audio 1/O Connects an extra microphone/speaker
Time Zone (GMT-08:00) Pacific Time US & Canada (not included)
Date Format MM-DD-YYYY © Tx/Rx LED Indicates if the Network is active © LAN Connects to your router
System Format 09-29-2014
System Time 18:14:37 © Video in Connects cameras via cat5e cables @ ns485 Connection for additional PTZ camera
We recommend checking ‘Enable DHCP’ even if your DVR is not
connected to the internet, this will automatically get the DVR
IP address. я
Wizard
@ us: Port
@ HDMiPort Connects to HDTV or computer monitor @ rower
Connects to a USB mouse or flash drive
(not Included)
(11) AC Power Connects the Power Supply
Power Switch
NIC Type 10M/100M Self-adaptive
=
ee re Troubleshooting
@)Laview
Premium IP NVR System
QUICK START GUIDE
Remote Viewing
The wizard will show additional network information, Problem Solution
click ‘Next’ to proceed. No display/No | - Make sure the VGA/HDMI cable is properly connected to both the DVR and TV/monitor View footage on your mobile devices with our SPP You can either
Wizard signal/Invalid | NOTE: A laptop sa be used as a screen scan the provided QR code below or search LaView Net in the app
format * Make sure your TV/monitor is on the correct video input (e.g. HDMI1, HDMI2, etc.) 8 0
Server Port 8000 | Try switdhing.to another 10800 TWimenitorandadus the outa resolution in the DUR store. Then scan the QR code located on the NVR for device P2P info.
HTTP Port 80 menu
RIF Pore 8558 * On the front of the DVR check that the power LED light is on ol
. No picture/No | * Make sure the camera is camera is properly connected to the PoE port on the NVR or PE [m] [m]
To initialize the hard drive click the ‘Init’ box otherwise the video network switch. If the camera does not support PoE or you are connecting it to a
App S
DVR will NOT record. non-PoE switch, you will need additional 12VDC power supply for the camera РР tore "
Cannot login | « The default user name is: admin and the default password is: 12345. If you don’t
Wizard remember your old password, please submit a ticket to us at ANDROID APP ON
www. lavi com/contact/. ole
Capacity Status Property Type Free Space y» Google play
M1 465.76GB Normal: RW Local 464GB Camera * Make sure the camera is not placed behind a window, there is no interference or a strong
picture is not light source in front of the camera
clear * In DVR Menu>Record>Parameter>Resolution, set the sub stream resolution to CIF for LaView NET SCAN ME
‚ o 7 ; all channels
If you wish to add an IP camera click ‘Search’ otherwise, * Move the camera to a different location and/or direction
click ‘Next’ to procee d. я NOTE: The live view (sub stream) resolution is NOT the actual image quality recorded (Main
Wizard stream); Connection of excessive length (over 300ft)ofcat5e cablewill drop the camera Content may vary by model, including the number of channels, cameras, configuration,
IP Address Amount Model image quality; Working at extreme weather condition (below -22F or above 140F) will drop and hard drive capacity.
va 192.168.1.36 1 CMIP3412 the image quality and damage the camera.
=
Night visionis | * The infrared activates automatically when the environment is dark enough. You can check Q t 2
not working that the camera infrared bulbs are working properly as they turn light red in dark u es I O n Ss =
Choose continuous or motion detection recording from the listed environments
Elick Di to finish recording Menu>HDD>General Open support ticket at: www.laviewusa.com/contact
ÿ ñ Enable the record mode (Normal or Motion Detection) under the Main : AE :
the wizard, Wizard SEN sta A pepe PIE Complete user manual can be viewed via included CD disc or can
KZ Start Recording be downloaded at: www.laviewusa.com/support.
We recommend testing all the cameras and cables prior to installation.
Wireless Router Connect your cameras
* Connect the Cat5e cable into the camera
* Connect the other end of the Cat5e cable into
the NVR PoE port.
(Repeat for all cameras)
Connect to your monitor/TV
* Connect your NVR and TV/monitor with a HDMI or
VGA cable (Not included)
Note: Your monitor/TV must support the output resolution of the
NVR or you may get a black screen or a possible error message. You
cannot use a laptop as a display.
Connect the mouse and power
DVR Adapter
| * Connect the mouse to the USB port
| * Connect the NVR power cable to the DVR
|
o usa o — — — Mouse
VGA
Connect to your network (OPTIONAL)
HDTV | * Connect the LAN port on the NVR to the LAN port
on your router via an Ethernet cable for remote
PC Monitor viewing on your mobile phone, tablets, PC and Mac
1920x1080 :
You can also add existing IP cameras to your NVR from
your network.
Note: The NVR will still work as a standalone video recorder if you do
not have internet connection and skip this step.
1080p
: `
Configure the start up wizard
* The connection is now completed. Turn on the
power switch and follow the start-up wizard on
your screen to configure the NVR. (Next Page)
">
