ICA-HM351 2 Mega-Pixel 35M IR Outdoor Box PoE IP Camera

User’s Manual
ICA-HM351
2 Mega-Pixel 35M IR Outdoor
Box PoE IP Camera
1
Copyright
Copyright © 2011 by PLANET Technology Corp. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or
its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, PLANET reserves the
right to revise this publication and to make changes from time to time in the contents hereof
without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance. (example-use only shielded interface cables when connecting
to computer or peripheral devices). Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must
accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment.
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
2
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer manufacture
must therefore be allowed at all times to ensure the safe use of the equipment.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users
of electrical and electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal
waste and have to collect such WEEE separately.
Revision
User’s Manual for PLANET 2 Mega-Pixel 35M IR Outdoor Box PoE IP Camera
Model: ICA-HM351
Rev: 1.0 (August. 2011)
Part No. EM-ICAHM351
3
Table of Content
1.
Introduction ............................................................................................................... 6
1.1 Overview ............................................................................................................. 6
1.2 Features .............................................................................................................. 6
1.3 Package Contents ............................................................................................ 7
2. Basic Setup .................................................................................................................. 8
2.1 System Requirements ...................................................................................... 8
2.2 Physical Description ......................................................................................... 9
2.2.1 Identification of ICA-HM351 cable ...................................................... 9
2.3 Hardware Installation ...................................................................................... 11
2.3.1 Physical Installation ............................................................................. 11
2.4 Initial Utility Installation ................................................................................... 12
2.5 Preparation ....................................................................................................... 14
2.5.1 Search and View by PLANET IPWizard ........................................... 14
2.6 Using UPnP of Windows XP, Vista or Win7 ................................................ 16
2.6.1 Windows XP ......................................................................................... 16
2.6.2 Windows Vista ...................................................................................... 21
2.6.3 Windows 7 ............................................................................................ 22
2.7 Install the Device behind a NAT Router ...................................................... 23
2.8 Setup ActiveX to use the Internet Camera ................................................. 24
2.8.1 Internet Explorer 6 for Windows XP .................................................. 24
2.8.2 Internet Explorer 7 for Windows XP .................................................. 25
,QWHUQHW([SORUHUIRU:LQGRZV9LVWDDQG:LQ ............................ 2
3 Web-based Management ..................................................................................... 27
3.1 Introduction ...................................................................................................... 27
3.2 Connecting to Internet Camera ..................................................................... 27
3.3 Live View .......................................................................................................... 29
3.4 ActiveX Control ................................................................................................ 32
3.4.1 Digital Zoom .......................................................................................... 32
3.4.2 Record ................................................................................................... 33
3.4.3 Snapshot ............................................................................................... 33
3.4.4 Voice ...................................................................................................... 34
3.4.5 Statistics ................................................................................................ 34
3.4.6 About ...................................................................................................... 35
3.5 System Setting ................................................................................................ 36
3.5.1 Network ................................................................................................. 37
3.5.2 HTTPS ................................................................................................... 39
3.5.3 DDNS server ........................................................................................ 40
3.5.4 PPPoE ................................................................................................... 41
3.5.5 Streaming .............................................................................................. 42
3.5.6 UPnP ...................................................................................................... 44
3.5.7 Bonjour .................................................................................................. 45
3.5.8 Onvif ....................................................................................................... 46
3.5.9 IP Filter .................................................................................................. 47
3.5.10 IP Notification ..................................................................................... 48
3.6 Camera Configuration .................................................................................... 50
3.6.1 Picture .................................................................................................... 50
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
4
3.6.2 Privacy Mask ........................................................................................ 52
3.6.3 PTZ Setting ........................................................................................... 53
3.6.4 Preset Setting ....................................................................................... 54
3.6.5 Tour Setting ........................................................................................... 54
3.7 System .............................................................................................................. 56
3.7.1 System ................................................................................................... 56
3.7.2 Date & Time .......................................................................................... 57
3.7.3 Maintenance ......................................................................................... 58
3.8 Video ................................................................................................................. 60
3.8.1 Common ................................................................................................ 60
3.8.2 Video Profile ......................................................................................... 61
3.8.3 ROI ......................................................................................................... 62
3.9 Audio Configuration ........................................................................................ 63
3.10 User Privilege Access Configuration .......................................................... 64
3.11 E-Mail Configuration ..................................................................................... 65
3.12 Object Detection ............................................................................................ 66
3.13 Event Server Configuration ......................................................................... 67
3.13.1 FTP Server ......................................................................................... 67
3.13.2 TCP Server ......................................................................................... 68
3.13.3 HTTP Server ....................................................................................... 69
3.13.4 SAMBA Server ................................................................................... 70
3.14 Event Schedule Configuration .................................................................... 71
3.15 Record Configuration ................................................................................... 75
Appendix A: Alarm I/O Connector ............................................................................... 76
Appendix B: PING IP Address ..................................................................................... 78
Appendix C: 3GPP Access ........................................................................................... 79
Appendix D: Bandwidth and Video Size Estimation ................................................. 80
Appendix E: DDNS Application .................................................................................... 81
Appendix F: Configure Port Forwarding Manually .................................................... 86
Appendix G: Troubleshooting & Frequently Asked Questions ................................ 89
Appendix H: Product Specification .............................................................................. 94
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
5
1. Introduction
0B
Thank you for purchasing the 2 Mega-Pixel series IP Camera, the ICA-HM351 bring users
high resolution surveillance both at day and night in outdoor. The ICA-HM351, the 2 Mega-Pixel
(1920 x 1080) 35 meters IR Outdoor PoE IP Camera, supports the highest video compression –
H.264, which provides small video size and save you lots of bandwidth usage. The new video
compression is the best solution for Internet video transmission. The ICA-HM351 supports
Multi-Profile Streaming function to generate H.264, MPEG-4 and M-JPEG streaming
simultaneously to differentiate users in different resolutions and frame rates. This state-of-the-art
design is considerable to fit in various network environments.
The ICA-HM351 provides 2-Way audio function for surveillance. It can remotely talk to
anyone at the ICA-HM351 site with additional speaker connected to the camera. Via two
ICA-HM351, users can easily communicate to each other for surveillance control. The ICA-HM351
Compliant with IEEE 802.3af PoE standard can be located in any place where there is no power
outlet available. Through Power over Ethernet, the installers are fearless for the power breakdown
at the remote site because the network devices can be powered from the central station where
UPS is installed.
The ICA-HM351 infrared Internet camera performs reliable operation in any environment.
With the Aluminum rugged all-weather housing enclosure, the ICA_HM351 maintains the reliable
operation in any environment. Moreover, it has built-in fan and heater to prevent the machine
overheated or sub cooling.
The ICA-HM351 follows the ONVIF v1.01 and v1.02 standard SDK for users to integrate with
the third party software. The ICA-HM351 can also work with PLANET Cam Viewer 3 Lite / Pro
Management software and Network Video Recorder products for video surveillance application
and provides monitoring, recording and event management functions to secure your property and
life.
1.1 Overview
11B
This user’s guide explains how to operate this camera from a computer. User should read this
manual completely and carefully before you operate the device
1.2 Features
12B
•
•
•
•
•
•
•
•
•
•
•
•
H.264, MPEG4 and MJPEG simultaneously (Tri-encoders)
High Quality FullHD 1080p Resolution
Built-in IR LED and visible distance up to 35 meters
IR-Cut filter brings better video quality in the daytime and nighttime
Compliant with IEEE 802.3af PoE interface
2-Way audio supported with external speaker and microphone
Support 3GPP for iPhone and Android phone for remote view
DDNS, PPPoE and FTP uploading offers more alternatives in surveillance network
10 Motion Detection feature can monitor any suspicious movement in a specific area
Easy configuration and management via Windows-Based utility or web browser
Supports ONVIF v1.0 and v1.02 / v1.01 Standard
Industrial design with -30 to 60 Degree C operating temperature
6
1.3 Package Contents
13B
User can find the following items in the package:
ICA-HM351 x 1
Power Adapter x 2
Wall Mounting Kit x 1
User’s Manual CD x 1
Quick Installation Guide x 1
NOTE:
1. If any of the above items are missing, please contact your dealer immediately.
2. Using the power supply that is not the one included in Internet camera packet
will cause damage and void the warranty for this product.
7
2. Basic Setup
1B
This chapter provides details of installing and configuring the internet camera
2.1 System Requirements
14B
CPU
Intel Dual Core 2.0GHz or higher
RAM
2GB (above Recommended)
Video RAM
NOTE:
128MB (above Recommended )
Display Resolution
1024 x 768 24bits or above
Operating System
Windows XP / Vista / Win7
DirectX
9.0c above
Network
Wired Ethernet 100Base-TX
The listed information is minimum system requirements only. Actual requirement will
vary depending on the nature of your environment.
8
2.2 Physical Description
15B
2.2.1 Identification of ICA-HM351 cable
37B
Interface
DC Power
(Power Jack, IR and IP
Camera)
RJ-45
(LAN socket, PoE, IR and
IP Camera )
Description
The input power is DC 12V, 1A.
Note:ONLY use package power adapter supplied with the
internet. Otherwise, the product may be damaged.
Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast
Ethernet cabling. This Ethernet port built auto-negotiation
protocol can detect or negotiate the transmission speed of the
network automatically. Please use CAT-5 cable to connect the
Network Camera to a 100Mbps Fast Ethernet network switch
or hub.
LAN LED (green color)
This LED will be flashing while network accessing via
Ethernet.
Power LED (orange color)
This LED is used to indicate whether DC power is on or not. In
addition, this LED will be flashing while the wireless accessing
of the Camera.
9
Note:ONLY use one power source, either from DC or from
802.3af Power over Ethernet.
Connect a loud speaker to the IP Camera. This is for voice
alerting and two-way audio.
Audio Output
(Green, Line Out)
Microphone Input
(Pink, Audio In)
Connect a microphone to the IP Camera.
The Network Camera also provides composite video output.
The video output function is only for easy installation to check
view angle and focus. Furthermore, only “720p Mode”
supports this function.
Video Output
(BNC)
This button is used to restore the all factory default settings.
Sometimes restarting the device will make the system back to
a normal state. However, if the system still got problems after
restart, user can restore the factory default settings and install
it again.
Restore the device:
Reset
(Factory Default)
DI/DO, RS-485
DC Power
(Power Jack, Fan and
Heater)
a.)
Press the button down continuously.
b.)
Hold the button at least 5 seconds and release it.
Then the device has been restored to default
settings and reboot again.
Note: Restoring the factory default setting will lose the all
previous settings included IP address forever. User needs to
run the IPWizard program to search the device and configure
it to let the device work properly again.
Connect RS-485 to external scanner and connect to sensor in
and alarm out devices.
The input power is DC 12V, 1A for Fan and Heater.
Note:That supplies the power to the built-in heater with the
power adapter included in package.
Terminal block for I/O connectors:
Name
Cable Color
12VDC
GND
D+
DDI
DO
Brown/White
Blue/White
Purple/White
Gray
Green/White
Orange/White
Function
DC 12V (50mA maximum)
GND
RS485 data +
RS485 data Digital signal input
Digital signal output
10
2.3 Hardware Installation
16B
2.3.1 Physical Installation
38B
1. Fix IR camera to desired location with wall mount fixture
2. Plug-in Ethernet Cable into RJ-45 connector
Connect an Ethernet cable to the LAN socket located on the Network Camera’s back panel
and attach it to the network.
NOTE:
If there has an IEEE 802.3af PoE switch in your network, you can connect the
camera LAN cable to this PoE switch to obtain power. The power adapter is
unnecessary when internet camera is connected to a PoE switch.
3. Connect RS485 D+ and D- (if you need to control PT scanner)
4. Attach the power supply
Connect the attached power adapters to camera and heater and plug-in these adapters into
power outlet
NOTE:
1. Only use the power adapter supplied with internet camera. Otherwise, the product
may be damaged.
2. The power adapter is unnecessary when internet camera is connected to a PoE
switch. Otherwise, the product may be damaged when internet camera is connected
to a PoE switch and power adapter simultaneously.
5. Attach BNC connector (option)
Connect the video BNC connector to a monitor set if necessary check camera viewing angle
and focus.
6 Attach Speaker to camera (option)
If user needs not only video stream but also audio stream, then the speaker should be
attached to camera.
7. Done
11
2.4 Initial Utility Installation
17B
This chapter shows how to quick set up your IP camera. The camera is with the default settings.
However to help you find the networked camera quickly the windows utility PLANET IPWizard can
search the cameras in the network that shall help you to configure some basic setting before you
started advanced management and monitoring.
1. Insert the bundled CD into the CD-ROM drive to launch the auto-run program. Once
completed, a welcome menu screen will appear.
2. Click the “IPWizard II” hyperlink; you will see the dialog box as below.
NOTE:
If the welcome screen does not appear, click “Start” at the taskbar. Then, select
“Run” and type “D:\Utility\IPWizard II\setup.exe”, assume D is your CD-ROM drive.
3. The “Welcome to the InstallShield Wizard for PLANET IPWizard II” prompt will display on the
screen and click “Next” to continue.
4. Please click “Next” to install with original settings, or you may click “Change…” button to
modify the install folder then press “Next” to continue.
12
5. Please click “Install” to start the installation.
6. Please click “Finish” to complete the installation and launch program immediately.
13
2.5 Preparation
18B
When you installed the camera on a LAN environment, you may execute PLANET IPWizard to
discover camera’s IP address and set up related parameters in the camera.
2.5.1 Search and View by PLANET IPWizard
39B
When you installed the Camera on a LAN environment, you have two easy ways to search your
Cameras by PLANET IPWizard II or UPnP discovery. Here is the way to execute PLANET
IPWizard II to discover Camera’s IP address and set up related parameter in a Camera.
Search
When launch the PLANET IPWizard II, a searching window will pop up. PLANET IPWizard II is
starting to search Network Cameras on the LAN. The existed devices will be listed as below.
14
View
If PLANET IPWizard II finds network devices, View button will be available. Please select the
device you want to view and click the View button. Then you could see the video from camera
directly. Furthermore you could double click the left button of mouse to link to the network device
by browser.
2.5.2 Configure Network by PLANET IPWizard
In case you want to change the IP related parameters of wired interface, please select the device
you want to configure and click the LAN button. Relative settings will be carried out as below.
You could modify the relative settings of the selected device. Click “<<” button will quit the LAN
setting procedure and click “>>” button will move to next page as below.
In case, you do not want to change username and/or password, then just click “Submit” button to
perform your setting accordingly. Click “<<” button will go back to previous page.
If you like to change username and/or password of the device, just click the check button. Then,
the related fields will show up as below.
15
After keying in new username and password, click “Submit” button to perform your setting
accordingly. Click “<<” button will go back to previous page.
2.6 Using UPnP of Windows XP, Vista or Win7
19B
2.6.1 Windows XP
40B
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled device. If the operating system, Windows XP, of your PC is UPnP enabled, the device will
be very easy to configure. Use the following steps to enable UPnP settings only if your operating
system of PC is running Windows XP.
NOTE:
Windows 2000 does not support UPnP feature.
Go to Start > Settings, and Click Control Panel
The “Control Panel” will display on the screen and double click “Add or Remove Programs” to
16
continue
The “Add or Remove Programs” will display on the screen and click Add/Remove Widows
Components to continue.
The following screen will appear, select “Networking Services” and click “Details” to continue
The “Networking Services” will display on the screen, select “Universal Plug and Play” and click
17
“OK” to continue.
Please click “Next” to continue
The program will start installing the UPnP automatically. You will see the below pop-up screen,
18
please wait while Setup configures the components.
Please click “Finish” to complete the UPnP installation
Double-click “My Network Places” on the desktop, the “My Network Places” will display on the
screen and double-click the UPnP icon with Internet camera to view your device in an internet
browser.
19
20
2.6.2 Windows Vista
41B
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled device. If the operating system, Windows Vista, of your PC is UPnP enabled, the device
will be very easy to configure. Use the following steps to enable UPnP settings only if your
operating system of PC is running Windows Vista.
Go to Start > Control Panel > Network and Internet > Network and Sharing Center, and turn
on “Network Discovery”.
Double-click “My Network Places“ on the desktop, the “My Network Places” will display on the
screen and double-click the UPnP icon with Internet camera to view your device in an internet
browser.
21
2.6.3 Windows 7
42B
Go to Start > Control Panel > Network and Internet > Network and Sharing Center, if network
discovery is off; click the arrow button
to expand the section.
Click Turn on network discovery, and then click Apply.
If you are prompted for an administrator
password or confirmation, type the password or provide confirmation.
22
2.7 Install the Device behind a NAT Router
20B
Once installed, the device is accessible on your LAN. To access the device from the Internet you
must configure your broadband router to allow incoming data traffic to the device. If the device is
installed on the LAN with a router, then it may get a dynamic IP address from the DHCP server.
However, if the device wants to be accessed from the WAN, its IP address needs to be setup as
fixed IP, also the port forwarding or Virtual Server function of router needs to be setup.
However, if your NAT router supports UPnP feature, it can be very easy to achieve NAT traversal
automatically. To do this, enable the NAT-traversal feature, which will attempt to automatically
configure the router to allow access to the camera.
Installing the device with an UPnP router on your network is an easy 3–step procedure:
(1) Enable UPnP option of your NAT router
(2) Enable UPnP NAT traversal option of the Network Camera (default)
(3) Access your Network Camera by DIPS
(1) Enable UPnP option of your NAT router
To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is enabled
in your router. Most new home routers should support this function. Some of routers are default
enable and others are not. Please check user’s manual of your NAT router for detail.
(2) Enable UPnP NAT traversal option of the Network Camera
Refer to Setting Î Network Î UPnP page for detail NAT traversal setting. Note that this option
is default enabled.
(3) Access your Network Camera by DIPS
Refer to Setting Î System Î System page for detail DIPS information
23
2.8 Setup ActiveX to use the Internet Camera
21B
The Internet camera web pages communicate with the Internet camera using an ActiveX control.
The ActiveX control must be downloaded from the Internet camera and installed on your PC. Your
Internet Explorer security settings must allow for the web page to work correctly. To use the
Internet camera, user must setup his IE browser as follows:
2.8.1 Internet Explorer 6 for Windows XP
43B
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” ΔCustom Level…”, please
setup your “Settings” as follow.
Set the first 3 items
• Download the signed ActiveX controls
• Download the unsigned ActiveX controls
• Initialize and script the ActiveX controls not masked as safe to Prompt
By now, you have finished your entire PC configuration for Internet camera.
24
2.8.2 Internet Explorer 7 for Windows XP
44B
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” ΔCustom Level…”, please
setup your “Settings” as follow.
Set the first 3 items
• Allow previously unused ActiveX control to run…
• Allows Script lets
• Automatic prompting for ActiveX controls
By now, you have finished your entire PC configuration for Internet camera.
25
2.8.3 Internet Explorer 7 for Windows Vista and Win7
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Internet” ΔCustom
Level…”, please setup your “Settings” as follow.
• Enable “Automatic prompting for ActiveX controls”
• Prompt “Initialize and script active controls not marked….”
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Trusted Sites”
ΔCustom Level…”, please setup your “Settings” as follow.
• Enable “Automatic prompting for ActiveX controls”
• Prompt “Initialize and script active controls not marked….”
By now, you have finished your entire PC configuration for Internet camera.
26
3 Web-based Management
2B
This chapter provides setup details of the Internet camera’s Web-based Interface.
3.1 Introduction
22B
The internet camera can be configured with your Web Browser. Before configure, please make
sure your PC is under the same IP segment with Internet camera.
3.2 Connecting to Internet Camera
23B
z
Use the following procedure to establish a connection from your PC to the camera.
z
Once connected, you can add the camera to your Browser’s Favorites or Bookmarks.
Start the web browser on the computer and type the IP address of the camera. The Default IP:
“ http://192.168.0.20 “
HU
UH
The login window of Internet camera will appear, Default login username/password is:
admin/ <no password>
;
NOTE:
If the User name and Password have been changed with PLANET IPWizard II,
please enter the new User name and Password here.
27
Web browser may display the “Security Warming” window, select “Yes” to install and run the
ActiveX control into your PC.
After the ActiveX control was installed and run, the first image will be displayed.
NOTE:
If you log in the camera as an ordinary user, setting function will be not available. If
you log in the camera as the administrator, you can perform all the settings provided
within the device.
28
3.3 Live View
24B
Start-up screen will be as follow no matter an ordinary users or an administrator.
Video Profile
ActiveX Control
Streaming Protocol
Monitor Image
Section
Language
Setting Menu
Client Menu
PTZ Control
2-Way Audio
Full Screen
Monitor Image Section
The image shot by the camera is shown here. The date and
time are displayed at the top of the window.
Video Profile
The camera support multi-profile for three compressions H264,
MEPG-4 and M-JPEG simultaneously. User can chose the
proper and/or preferred profile here.
Full Screen
Click this button to display the image in full-screen mode (uses
every available space to display the image captured by this
camera).
2-Way Audio
The Internet camera supports 2-way audio function. User can
chose to enable or disable this function by toggling the icon
below
: Disable audio uploading function.
: Enable audio uploading function.
ActiveX Control
The plug-in ActiveX control supports a lot of functions by
clicking the left mouse button. Note that this feature only
supports on the ActiveX control within Microsoft® Internet
Explorer.
Setting Menu
This function is detail setting for the camera that only available
29
for user logged into camera as administrator.
Item
Action
Network
Configure Network settings such as Wireless,
DHCP, DDNS, 3GPP, PPPoE and UPnP.
Camera
Adjust camera parameters.
System
Configure system information, date & time,
maintenance, and view system log file.
Video
Configure bit rate and frame rate of video
profiles.
Audio
Configure audio parameters.
User
Setup user name, password and login privilege.
E-Mail
FTP
Setup E-Mail configuration.
This devise is a client site and configure
information to upload images to server.
Object
Detection
Setup Object detection.
Event
Schedule
Configure the schedule while event triggered.
Streaming Protocol
User can select proper streaming protocol according to
networking environment.
Language
The device could provide multiple languages to meet
customer’s requirement.
Video Information
Display video information including video format, resolution,
frame rate and bit rate.
Client Setting
Click this button to display the client extra control panel for
2-way Audio and Full Screen.
PTZ Control
Click to display the following control panel:
30
Hide PTZ Control
Camera Direction
Camera Speed
Preset
Tour
Go Tour
Auto Pan
Hide PTZ Control
Click the icon will hide the PTZ control function.
Camera Direction
Control camera up/down/left/right and home position.
Camera Speed
Choose the speed of Pan and Tilt.
Preset
Add/Update the preset positions or go to one of these positions.
Tour
Select one of the camera tours. Camera tour is comprised by series of
preset locations.
Go Tour
Execute the selected camera tour.
Auto Pan
Execute the auto pan of camera. While auto pan is running, the
camera will swing the camera automatically. Note that the speed of
auto pan is fixed and cannot be adjustable.
NOTE:
If you want to use the PTZ function, it must be connected an external PTZ via RS485
interface. The PTZ function can be enabled. If not then the PTZ function is disabled.
31
3.4 ActiveX Control
25B
The plug-in ActiveX control supports a lot of functions by clicking the left mouse button. Note that
this feature only supports on the ActiveX control within Microsoft® Internet Explorer.
On the ActiveX control icon, click the Left Mouse Button, then a menu pop-up. This menu provides
features that are unique to the ActiveX control. These features include:
• Record,
• Snapshot,
• Voice,
• Statistics,
• About
3.4.1 Digital Zoom
45B
Click Digital Zoom to active this function as above. User can drag or scale the box over the video
to adjust zoom ratio and position.
32
3.4.2 Record
46B
Click Record to activate this function. Press Record button to start recording. The video file is
saved as ASF format into your local PC. While you want to stop it, press Stop to stop recording.
Select Browser, the pop-up window to select the save path and file name prefix, select OK to
continue.
After stop recording, list the files, this file is named as Video_yyyymmddhhmmss.asf
The ASF files can be display by the standard Windows Media Player, but it needs the DixectX 9.0
or later version to be installed.
NOTE:
Default save path is “C:\Documents and Settings\All user\Desktop
3.4.3 Snapshot
47B
Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is
saved as JPEG format into your local PC. Select Browser, the pop-up window to select the save
path and file name prefix, select OK to continue.
If you like to retrieve the saved image, select the file to display the saved image by using any one
of graph editing tools.
NOTE:
Default save path is “C:\Documents and Settings\All user\Desktop
33
3.4.4 Voice
48B
Click Volume to activate this function. These have two control bars for speaker and microphone
volume. Scroll this control bar to adjust the audio attribute. Check the volume mute will mute the
speaker output.
3.4.5 Statistics
49B
Click Statistics to activate this function. A window will be popup to show the statistics information
of the streaming status.
NOTE:
That this information is the statistics between the device and your local PC.
34
3.4.6 About
50B
Click About to show the ActiveX information
35
3.5 System Setting
26B
Use this menu to configure the network to connect the device and the clients.
This function is only available for user logged into Camera as administrator.
Click on each menu name to display its setting page.
Item
Action
Network
Configure Network settings such as DHCP, DDNS, 3GPP, PPPoE and
UPnP.
Camera
Adjust camera parameters, position, and set camera tour.
System
Configure system information, date & time, maintenance, and view
system log file.
Video
Configure bit rate and frame rate of video profiles.
Audio
Configure audio parameters.
User
Setup user name, password and login privilege.
E-Mail
Setup E-Mail configuration.
Object Detection
Setup Object detection.
Event Server
Setup FTP/TCP/HTTP server for event.
Event Schedule
Configure the schedule while event triggered.
36
3.5.1 Network
51B
This section provides the menu of connecting the device through Ethernet cable.
MAC address
Display the Ethernet MAC address of the device. Note that user cannot
change it.
Obtain an IP address
automatically (DHCP)
Enable this checked box when a DHCP server is installed on the
network to issue IP address assignment. With this setting, the IP
address is assigned automatically. If this device cannot get an IP
address within limited tries, the device will assign a default IP address
for 192.168.0.20.
If you do not select “Obtain an IP address automatically”, then you
need to enter these network parameters by yourself.
IP Address
This address is a unique numbers that identifies a computer or device
on the WAN or LAN. These numbers are usually shown in groups
separated by periods, for example: 192.168.0.200
Subnet Mask
Subnets allow network traffic between hosts to be separated based on
the network's configuration. In IP networking, traffic takes the form of
packets. IP subnets advance network security and performance to
some level by organizing hosts into logical groups. Subnet masks
contain four bytes and usually appear in the same "dotted decimal"
data. For example, a very common subnet mask in its binary
37
demonstration 11111111 11111111 11111111 00000000 will usually be
shown in the corresponding, more readable form as 255.255.255.0.
Gateway
A gateway is a piece of software or hardware that passes information
between networks. You'll see this term most often when you either log
in to an Internet site or when you're transient email between different
servers.
Obtain DNS from
DHCP
Enable this checked box when a DHCP server is installed on the
network and provide DNS service.
Primary DNS
When you send email or position a browser to an Internet domain such
as xxxxx.com, the domain name system translates the names into IP
addresses. The term refers to two things: the conventions for naming
hosts and the way the names are control across the Internet.
Secondary DNS
The same function as DNS1. It is option not necessary
HTTP Port
The device supports two HTTP ports. The first one is default port 80
and this port is fixed. This port is very useful for Intranet usage. The
second HTTP port is changeable. Users could assign the second port
number of http protocol, and the WAN users should follow the port
number to login. If the http port is not assigned as 80, users have to
add the port number in back of IP address. For example:
http://192.168.0.20:8080 .
U
U
Therefore, the user can access the device by either
http://xx.xx.xx.xx/ , or
U
U
http://xx.xx.xx.xx:xxxx/ to access the device.
U
U
If multiple devices are installed on the LAN and also required to be
accessed from the WAN, then the HTTP Port can be assigned as the
virtual server port mapping to support multiple devices.
NOTE
When the configuration is finish, please click “OK” to save and enable
the setting.
38
3.5.2 HTTPS
52B
HTTPS: Stands for Hypertext Transfer Protocol Secure
HTTPS is a combination of the Hypertext Transfer Protocol with the SSL/TLS protocol to provide
encrypted communication and secure identification of a network web server . HTTPS connections
are often used for sensitive transactions in corporate information systems. The main idea of
HTTPS is to create a secure channel over an insecure network. This ensures reasonable
protection from eavesdroppers and man-in-the-middle attacks , provided that adequate cipher
suites are used and that the server certificate is verified and trusted.
H
H
H
H
H
H
H
H
H
H
HTTPS
To enable or disable the HTTPS service here. Note that the HTTPS
function of this device is not only encrypted the web content but also
audio/video data.
Port
Choose the HTTPS port. The default value is 443.
39
3.5.3 DDNS server
53B
DDNS: Stands for Dynamic Domain Name Server
The device supports DDNS If your device is connected to xDSL directly, you might need this
feature. However, if your device is behind a NAT router, you will not need to enable this feature.
Because DDNS allows the device to use an easier way to remember naming format rather than an
IP address. The name of the domain is like the name of a person, and the IP address is like his
phone number. On the Internet we have IP numbers for each host (computer, server, router, and
so on), and we replace these IP numbers to easy remember names, which are organized into the
domain name. As to xDSL environment, most of the users will use dynamic IP addresses. If users
want to set up a web or a FTP server, then the Dynamic Domain Name Server is necessary. For
more DDNS configuration, please consult your dealer.
Your Internet Service Provider (ISP) provides you at least one IP address which you use to
connect to the Internet. The address you get may be static, meaning it never changes, or dynamic,
meaning it’s likely to change periodically. Just how often it changes, depends on your ISP. A
dynamic IP address complicates remote access since you may not know what your current WAN
IP address is when you want to access your network over the Internet. The solution to the dynamic
IP address problem comes in the form of a dynamic DNS service.
The Internet uses DNS servers to lookup domain names and translates them into IP addresses.
Domain names are just easy to remember aliases for IP addresses. A dynamic DNS service is
unique because it provides a means of updating your IP address so that your listing will remain
current when your IP address changes. There are several excellent DDNS services available on
the Internet and best of all they’re free to use. One such service you can use is www.DynDNS.org.
You’ll need to register with the service and set up the domain name of your choice to begin using it.
Please refer to the home page of the service for detailed instructions or refer to Appendix E for
more information.
40
DDNS
To enable or disable the DDNS service here.
Server name
Choose the built-in DDNS server.
DDNS Host
The domain name is applied of this device.
User Name
The user name is used to log into DDNS.
Password
The password is used to log into DDNS.
3.5.4 PPPoE
54B
PPPoE: Stands for Point to Point Protocol over Ethernet
A standard builds on Ethernet and Point-to-Point network protocol. It allows Internet camera
connects to Internet with xDSL or cable connection; it can dial up your ISP and get a dynamic IP
address. For more PPPoE and Internet configuration, please consult your ISP.
It can directly connect to the xDSL, however, it should be setup on a LAN environment to program
the PPPoE information first, and then connect to the xDSL modem. Power on again, then the
device will dial on to the ISP connect to the WAN through the xDSL modem.
The procedures are
• Connect to a LAN by DHCP or Fixed IP
• Access the device, enter Setting Î Network Î PPPoE as below
41
PPPoE
To enable or disable the PPPoE service here.
User Name
Type the user name for the PPPoE service which is provided by
ISP.
Password
Type the password for the PPPoE service which is provided by
ISP.
IP Address / Subnet
Mask / Gateway
Shows the IP information got from PPPoE server site.
Status
Shows the Status of PPPoE connection.
3.5.5 Streaming
55B
RTSP is a streaming control protocol, and a starting point for negotiating transports such as RTP,
multicast and Unicast, and for negotiating codecs. RTSP can be considered a "remote control" for
controlling the media stream delivered by a media server. RTSP servers typically use RTP as the
protocol for the actual transport of audio/video data.
42
RTSP Port
Choose the RTSP port. The RTSP protocol allows a connecting client to
start a video stream. Enter the RTSP port number to use. The default value
is 554.
RTP Port
Specify the range of transmission port number of video stream. The default
range is 50000 to 50999. User can specify a number between 1024 and
65535.
NOTE
1. To use the 3GPP function, in addition to previous section, you might
need more information or configuration to make this function work.
2. The camera must be set as Multi-profile mode, not Mega-pixel mode.
Otherwise this device cannot serve 3GPP stream.
3. To use the 3GPP function, it strongly recommends installing the
Networked Device with a public and fixed IP address without any
firewall protection.
4. Port 554 is the default for RTSP service. However, sometimes, some
service providers change this port number for some reasons. If so,
user needs to change this port accordingly.
Dialing
procedure
1. Choose a verified player (PacketVideo, QuickTime or Real player
currently)
2. Use the following URL to access: rtsp://host/mpeg4/media.3gp
Where host is the host name or IP address of the camera.
Compatible
3G mobile
phone
Please contact your dealer to get the approved list of compatible 3G
phone.
43
3.5.6 UPnP
56B
UPnP is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled Network Camera. If your operating system is UPnP enabled, the device will automatically
be detected and a new icon will be added to “My Network Places.” If you do not want to use the
UPnP functionality, it can be disabled
In addition, this device also provides UPnP IGD function for NAT traversal easily. Use NAT
traversal when your device is located on an intranet (LAN) and you wish to make it available from
the other (WAN) side of a NAT router. With NAT traversal properly configured, all HTTP traffic to
an external HTTP port in the NAT router will be forwarded to the device.
UPnP
To enable or disable the UPnP service here.
Friendly Name
Shows the friendly name of this device here.
UPnP NAT Traversal
When enabled, the device will attempt to configure port mapping in
a NAT router on your network, using UPnP™. Note that UPnP™
must be enabled in the NAT router first.
Port Range
The port range will open in NAT router.
External IP address
Show the IP address and port for WAN access through Internet. If
NAT traversal is configured successfully, user can use this IP
address and port to access this device.
44
3.5.7 Bonjour
57B
Bonjour, also known as zero-configuration networking, enables automatic discovery of computers,
devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow
devices to automatically discover each other without the need to enter IP addresses or configure
DNS servers. Specifically, Bonjour enables automatic IP address assignment without a DHCP
server, name to address translation without a DNS server, and service discovery without a
directory server. Bonjour is an open protocol which Apple has submitted to the IETF as part of the
ongoing standards-creation process.
Bonjour
To enable or disable the Bonjour service here.
Friendly Name
To show the friendly name of this device here.
45
3.5.8 Onvif
58B
ONVIF is a global and open industry forum with the goal to facilitate the development and use of a
global open standard for the interface of physical IP-based security products. Or in other words, to
create a standard for how IP products within video surveillance and other physical security areas
can communicate with each other.
ONVIF
To enable or disable the ONVIF interface here.
Version
Currently, the V1.0 or V1.01/1.02 is available.
46
3.5.9 IP Filter
59B
You can enter different user’s IP address which are allowing enter or denying by the device.
IP Filter
To enable or disable the IP filter function here.
IP Filter Policy
Choose the filter policy where is denying or allowing.
47
3.5.10 IP Notification
60B
In case the IP address is changed, system is able to send out an email to alert someone if the
function is enabled.
SMTP Notification (e-mail)
If enable this function, then the “Send to“ and “Subject” field
need to be filled.
Send To
Type the receiver’s e-mail address. This address is used for
reply mail.
Subject
Type the subject/title of the E-mail.
TCP Notification
If enable this function, then the “TCP Server“, “TCP Port”,
and “Message” fields need to be filled.
TCP Server
Type the server name or the IP address of the TCP server.
TCP Port
Set port number of TCP server.
Message
The message will be sent to FTP server.
HTTP Notification
If enable this function, then the fields below need to be filled.
URL
Type the server name or the IP address of the HTTP server
48
HTTP Login name
Type the user name for the HTTP server.
HTTP Login Password
Type the password for the HTTP server.
Proxy Address
Type the server name or the IP address of the HTTP Proxy.
Proxy Port
Set port number of Proxy.
Proxy Login name
Type the user name for the HTTP Proxy.
Proxy Login Password
Type the password for the HTTP Proxy.
Custom parameter
User can set specific parameters to HTTP server.
Message
The message will be sent to HTTP server.
49
3.6 Camera Configuration
27B
Use this menu to set the function of the camera of Internet camera
3.6.1 Picture
61B
Rotation
Turn the “Mirror” and “Vertical Flip” On or OFF. The image will be
overturned as below.
White Balance:
Auto: will adjust the white balance automatically.
Hold: will hold the white balance.
50
Power Frequency
Frequency of power line: 50 or 60Hz
Color Level
Large value will be colorful.
Hue
Change the value will result to color tuning.
Brightness
Large value will brighten camera.
Contrast
Large value will contrast camera heavily.
Sharpness
Large value will sharpen camera.
IR LEDs (Night Vision)
User can turn Auto/Off/On/Schedule of the night mode. This
function is very useful under low illumination environment.
This is an optional function by model. In case, the camera is
built-in ICR, user can configure these parameters to control ICR
function. There are 4 modes of ICR: Night, Day, Auto and
Schedule. In case the Auto mode is selected, user needs to
specify 3 parameters in advance:
Night Mode Threshold (0~10000):
this value set the threshold to activate night mode. It should be
lower or equal to Day Mode Threshold.
Day Mode Threshold (0~10000):
this value set the threshold to activate day mode. It should be
higher or equal to Night Mode Threshold.
Delay Time: The delay time between ICR switching.
Note that Current Value is the current luminance from the
captured video. It’s a useful reference to set Day/Night Mode
Threshold.
De-Noise
De-Noise can remove or lower unwanted noise and preserve fine
details and edges.
Default Settings
Restore to factory image settings.
51
3.6.2 Privacy Mask
62B
Use this page to specify privacy mask window 1 to window 8 and set the name and gray level for
selected window.
Add and Delete
To add or delete the privacy mask windows, user can specify up to 7
windows to mask the video captured by this device. By dragging
mouse on the image, you can change the position and size of the
selected window accordingly.
Name
Name of the specified privacy window
Level
To define the gray level of mask block. The smaller value will be
darker.
52
3.6.3 PTZ Setting
63B
This page allow user to modify the RS-485 interface according to the P/T scanner.
Camera Protocol
This device can connect to a PTZ camera or speed dome camera and
controls them thru RS-485 interface.
Camera Address
This is the camera ID set in PTZ camera or speed dome camera.
Note that please DO NOT changes the default value if unnecessary.
If so, user needs to check and set value properly for both sides.
Baud rate
This is the communication speed between network module and P/T
scanner.
NOTE
If need to change these parameters, user needs to check and set
value properly for both, network module and P/T scanner.
53
3.6.4 Preset Setting
64B
This page provides the edit tool to modify or delete the “Preset Setting” item by item.
3.6.5 Tour Setting
65B
Up to 64 positions can be preset, and the camera can be programming to move to the preset
position sequentially.
54
Tour Name
The group name of the sequence of camera tour. The maximum number of
camera tour is 16.
Running
Enable or disable this camera tour.
Preset
Set the sequence of the tour. Maximum 16 points can be assigned. The
selected preset position is added in the Sequence list from 1 to 16.
Wait Time
Type a period of time during which the camera is to stay at each preset point,
between 0 to 36000 seconds.
NOTE
To use the camera tour function, user must preset some camera positions
first. The maximum number of preset points is 64.
55
3.7 System
28B
Use this menu to perform the principal settings of Internet camera.
3.7.1 System
66B
Device title
You can enter the name of this unit here. It’s very useful to identify the
specific device from multiple units.
Software version
This information shows the software version in the device.
Network LED
Switch the LED light of this Internet camera on or off, that Network
LEDs will stop working, in case you don’t want other people know the
camera is transferring data.
Power LED
Switch the LED light of this Internet camera on or off.
Log
User can check the system log information of the device, including the
Main Info, Appended Info, Operator IP, and so on …
Reload
Click this button; user can refresh the log information of the device.
56
3.7.2 Date & Time
67B
You can setup the time setting of Internet camera, make it synchronized with PC or remote NTP
server. Also, you may select the correct time zone of your country.
Server Date
Displays the date and time of the device
& Time
PC Time
Displays the date and time of the connected PC
Adjust
Synchronize
with PC
Click this option to enable time synchronization
with PC time
Manual setting
Click this option to set time and date manually
Synchronize
with NTP
Click this option if you want to synchronize the
device’s date and time with those of time server
called NTP server (Network Time Protocol)
NTP server name
Type the host name or IP address or domain name of the NTP
server.
NTP sync. Interval
Select an interval between 1 and 23 hours at which you want to
adjust the device’s time referring to NTP server
Time zone
Set the time difference from Greenwich Mean Time in the area
where the device is installed.
57
Daylight saving
Check this item to enable daylight saving adjustment.
Daylight Saving
Sets up the date and time of daylight saving start time.
Start Time
Daylight Saving
Sets up the date and time of daylight saving stop time.
Stop Time
Daylight Saving
Sets up the date of daylight saving offset.
Offset
3.7.3 Maintenance
68B
Default Settings
(Include the network
setting)
Recall the device hard factory default settings. Note that click
this button will reset all device’s parameters to the factory
settings (including the IP address).
Default Settings
(Except the network
setting)
The unit is restarted and most current settings are reset to
factory default values. This action will not reset the network
setting.
Backup Setting
To take a backup of all of the parameters, click this button. If
necessary, it will then be possible to return to the previous
settings, if settings are changed and there is unexpected
behavior.
58
Restore Setting
Click the “Browse” button to locate the saved backup file and
then click the “Restore Setting” button. The settings will be
restored to the previous configuration.
Firmware upgrade
The device supports new firmware upgrade.
1. Close all other application programs which are not
necessary for firmware update.
2. Make sure that only you access this device at this moment
3. Disable Motion Detection function.
4. Select “Firmware name”
5. Select the Firmware binary file.
Note!! That it must make sure that the Firmware only applies to this device, once update, it
will be burned into FLASH ROM of system.
6. Once the firmware file was selected, select “Upgrade”.
7. The upgrade progress information will be displayed on the
screen.
8. A message will be shown while the firmware upgraded.
Once the upgrading process completed, the device will
reboot the system automatically.
9. Please wait for 80 seconds, and then you can use PLANET
IPWizard II to search the device again.
Warning!!! The download firmware procedure cannot be interrupted. If the power
and/or network connection are broken during the download procedure, it might
possibly cause serious damage to the device.
Please be aware that you should not turn off the power during updating the firmware
and wait for finish message.
Furthermore, do not try to upgrade new firmware if it’s not necessary.
System Restart
The device is restarted without changing any of the settings.
59
3.8 Video
29B
This device provides 2 modes of video profile. The first one is Mega-pixel mode which supports
video resolution up to Mega-pixel. However the maximum frame rate of this mode is up to 15fps
only. The second one is VGA mode which supports video resolution up to VGA but frame rate can
be up to 30fps. User only can select either Mega-pixel or VGA mode to operate the camera.
Switching Mega-pixel and VGA, the device will take time to reboot system.
3.8.1 Common
69B
Video Profile
User can only choose either 720p or 2 Mega modes. 720p mode
can serve H.264, MPEG4, and JPEG streams up to 1280x720
resolutions maximum. On the other hand, 2 Mega mode, it can
streams up to 1080p or 1600x1200 resolution (depend on model)
maximum.
Note that this camera supports local video output for TV monitor.
It’s very useful to check view angle or focus during camera
installation. However, the local video output in only available at
“720p” mode. If user needs this function, must switch this camera
to “720p” mode first.
Text Overlay Setting
There are some important information can be embedded into
image, including date, time, and/or text.
60
3.8.2 Video Profile
70B
It’s H.264 encoder mode in this profile.
Name
To assign a name to the selected profile.
Video Type
Video codec of the selected profile.
Resolution
Resolution of the selected profile.
ROI
Assign the selected profile as a ROI stream or not. (Only available
for the profiles with max resolution)
Rate Control
Defines the rate control method of this profile. There are four
options: Constant Bit Rate (CBR), Variable Bit Rate (VBR),
Enhanced Constant Bit Rate (ECBR), and Enhanced Variable Bit
Rate (EVBR).
For CBR, the video bit rate is between low to high bandwidth based
on different resolutions. User can set the desired bit rate to match
the limitation of bandwidth.
For VBR, user should choose the quality level to set the video quality
rather than bit rate. The quality level is between 1 and 100. The
higher value can reach the better quality but of course will consume
higher bandwidth.
61
For ECBR, the video bitrates is based on normal CBR mode.
However, the target bitrates can be increased to max target bitrate
while lots of motion in video. The max target bitrates will keep a
pre-defined time period and then back to normal CBR bitrates.
For EVBR, the video bitrates is based on normal VBR mode.
However, the target bitrates can be increased to max target bitrates
while lots of motion in video. The max target bitrates will keep a
pre-defined time period and then back to normal VBR mode.
Max Frame Rate
Defines the targeted frame rate of this profile. For example, set the
frame rate to 15 fps, then the image will be updated for 15 frames
per second. User can set the desired max frame rate versus video
quality under the limited bandwidth.
GOP Control
Defines the Intra/Inter-frame (I/P) ratio of this profile. For example,
set the GOP to 30, then the video stream will have one Intra-frame
every 30 frames.
3.8.3 ROI
71B
ROI means Region of Interest. Use this page to specify location of ROI windows. Only the
maximum resolution profiles can be defined as ROI. In this model, the default ROI windows are
profile 4 and 5.
62
3.9 Audio Configuration
30B
It’s M-JPEG mode in this profile.
Audio
To enable or disable audio function
Mute While PT
Mute the audio while pan and/or tilt motion
Audio Mode
To select Simplex or Full duplex (2-way audio) mode.
Input Gain
To adjust gain of input audio
Output Gain
To adjust gain of output audio
63
3.10 User Privilege Access Configuration
31B
Use this menu to set the user names and password of the Administrator and up to 10 users, and
access right of each user.
Viewer login
Select “Anonymous” to allow any one viewing the video once
connected. Otherwise, only users in database can view the
video after login.
Access right
Administrator can access every function in this device.
However, Viewers only can view the video and access
limited function.
PTZ Control
Authorize this user to control PTZ function or not.
Add, update, and remove
of Users account
Manage the user’s account of viewer user.
64
3.11 E-Mail Configuration
32B
You may setup SMTP mail parameters for further operation of Event Schedule. That’s, if users
want to send the alarm message out, it will need to configure parameters here and also add at
least one event schedule to enable event triggering.
SMTP Server
Type the SMTP server name or the IP address of the SMTP server.
Test
Send a test mail to mail server to check this account is available or
not.
SMTP Port
Set port number of SMTP service.
SSL
Enable SSL function or not.
Select the authentication required when you send an e-mail.
SMTP Authentication
Disable: If no authentication is required when an e-mail is send.
Enable: If authentication is required when an e-mail is sent.
Authentication
Name
User
Type the user name for the SMTP server if Authentication is Enable.
Authentication Password
Type the password for the SMTP server if Authentication is Enable.
E-mail From
Type the sender’s E-mail address. This address is used for reply
65
e-mails.
E-mail To
Type the receiver’s e-mail address.
E-mail Subject
Type the subject/title of the e-mail.
3.12 Object Detection
33B
Use this menu to specify motion detection window 1 to window 4 and set the conditions for
detection while observing a captured image.
Add and Del
To add or delete the motion windows. User can specify up to 4
Included and/or Excluded windows to monitor the video captured by
this device. By dragging mouse on the image, you can change the
position and size of the selected motion window accordingly.
Included or Excluded
Window
These windows can be specified as Included or Excluded type.
Included:
Windows target specific areas within the whole video image
Excluded:
Windows define areas within an Include window that should be
ignored (areas outside Include windows are automatically ignored)
Name
Name of the specified motion window.
66
Object Size
Defines the object size of motion detection. The higher object size will
only larger objects trigger motion detection. The lower object size will
even small objects trigger motion detection too. Generally speaking,
the smaller size will be easier to trigger event.
Sensitivity
Defines the sensitivity value of motion detection. The higher value will
be more sensitivity.
3.13 Event Server Configuration
34B
3.13.1 FTP Server
72B
You may setup FTP parameters for further operation of Event Schedule. That’s, if users want to
send the alarm message to an FTP server, it will need to configure parameters here and also add
at least one event schedule to enable event triggering as SMTP.
Name
User can specify multiple FTP paths as wish. Therefore, user
needs to specify a name for each FTP setting.
FTP Server
Type the server name or the IP address of the FTP server.
Test
Check the FTP server whether this account is available or not.
FTP Login name
Type the user name for the FTP server.
67
FTP Login Password
Type the password for the FTP server.
FTP Port
Set port number of FTP service.
FTP Path
Set working directory path of FTP server.
FTP Passive Mode
Select passive or active mode connecting to FTP server.
3.13.2 TCP Server
73B
In addition to send video file to FTP server, the device also can send event message to specified
TCP server.
Name
User can specify multiple TCP servers as wish. Therefore, user
needs to specify a name for each TCP server setting.
TCP Server
Type the server name or the IP address of the TCP server.
TCP Port
Set port number of TCP server.
68
3.13.3 HTTP Server
74B
The device also can send event message to specified HTTP server.
Name
User can specify multiple HTTP servers as wish. Therefore, user
needs to specify a name for each HTTP server setting.
URL
Type the server name or the IP address of the HTTP server.
Test
Check the HTTP server whether it is available or not.
HTTP Login name
Type the user name for the HTTP server.
HTTP Login Password
Type the password for the HTTP server.
Proxy Address
Type the server name or the IP address of the HTTP Proxy.
Proxy Login name
Type the user name for the HTTP Proxy.
Proxy Login Password
Type the password for the HTTP Proxy.
Proxy Port
Set port number of Proxy.
69
3.13.4 SAMBA Server
75B
The device also can send video stream to specified SAMBA server. Most of the time, the SAMBA
server will be another PC or NAS server.
Name
User can specify multiple HTTP servers as wish. Therefore, user
needs to specify a name for each HTTP server setting.
SAMBA Server
Type the server name or the IP address of the SAMBA server.
Test
Check the SAMBA server whether this account is available or not.
SAMBA Login name
Type the user name for the SAMBA server.
SAMBA Login Password
Type the password for the SAMBA server.
SAMBA Path
Set working directory path of SAMBA server.
70
3.14 Event Schedule Configuration
35B
This menu is used to specify the schedule of Events and activate the some actions provided by
this device.
Name
Name of the Event or Schedule.
Enable
Enable or disable this Event or Schedule.
Type
Schedule start with Event trigger or Schedule trigger.
Enable Time
Define the feasible time slot.
Trigger by
Select the triggered sources with event trigger.
Action
Define the actions once event triggered.
71
Example1.
Send file to FTP server by motion triggered always:
1.
Select event trigger
2.
Enable time: start from 00:00 to 24:00 every day
3.
Trigger by: Motion Area (Added in Object Detection page)
4.
Action : Send FTP (Add in Event Server -> FTP Server page)
72
Example2.
Send file to E-Mail server by motion triggered from Friday 18:00 to Saturday
06:00
1.
Select event trigger.
2.
Enable time: start from Friday 18:00 and keep work in 12 hours, so
it will stop on Saturday 06:00.
3.
Trigger by : Motion Area (Added in Object Detection page)
4.
Action : Send e-mail (Add in E-Mail page)
i.
To email address: You need to input the receiver email
address.
ii.
Subject: You could specify the email subject.
iii.
Message: You could specify the email content.
73
Example3.
Send file to E-Mail server by motion triggered from Friday 18:00 to 24:00 from
Monday to Friday.
1.
Type: Select schedule trigger and interval is 10-minute.
2.
Enable Time: Select Monday to Friday, and set start time from 18:00
and keep work in 6 hours.
3.
Trigger by: You do not need to choose it, because this will be
triggered every minute.
4.
Action: Voice Alert.
74
3.15 Record Configuration
36B
User can choose the type of record file for event or schedule application.
Record File Type
Choose AVI or JPEG file format for record file.
Record File Prefix
Define the prefix of recorded filename.
Pre-Trigger Duration
Define the maximum duration of pre-alarm.
Best Effort Duration
Define the best effort duration of post-alarm.
Max File Size
Define the maximum buffer size of record file.
75
Appendix A: Alarm I/O Connector
3B
Some features of the Camera can be activated by the external sensor that senses physical
changes in the area Camera is monitoring. These changes can include intrusion detection or
certain physical change in the monitored area. For examples, the external sensor can be a door
switch or an infrared motion detector. These devices are customer provided, and are available
from dealers who carry surveillance and security products. Electrically, they must be able to
provide a momentary contact closure.
This Camera provides wires for general I/O terminal and RS-485 interface as below:
Cable for I/O connectors:
Name
Cable Color
12VDC
Brown/White
GND
Blue/White
D+
Purple/White
DGray
DI
Green/White
DO
Orange/White
Function
DC 12V (50mA maximum)
GND
RS-485 data +
RS-485 data Digital signal input
Digital signal output
User can refer to the schematic below to make a proper connection between I/O connector and
external sensor and output device.
Explanation of External I/O Circuit Diagram:
76
CAUTION!
9
The low voltage/current circuits and high voltage/current circuits are in the
network camera circuit. The qualified electrician should do the wring not by
yourself incorrect wiring could damage network camera. You could receive
the fatal electric shock.
9
The external I/O is not capable of connecting directly to devices that require
large amounts of current. In some cases, a custom interface circuit (customer
provided) may have to be used. Serious damage to network camera may
result if a device is connected to the external I/O that exceeds its electrical
capability.
77
Appendix B: PING IP Address
4B
The PING (stands for Packet Internet Groper) command is used to detect whether a specific IP
address is accessible by sending a packet to the specific address and waiting for a reply. It’s also
a very useful tool to confirm Internet camera installed or if the IP address conflicts with any other
devices over the network.
If you want to make sure the IP address of Internet camera, utilize the PING command as follows:
z
Start a DOS window.
z
Type ping x.x.x.x, where x.x.x.x is the IP address of the Internet camera.
The replies, as illustrated below, will provide an explanation to the problem.
If you want to detect any other devices conflicts with the IP address of Internet camera, also can
utilize the PING command but you must disconnect the Internet camera from the network first.
78
Appendix C: 3GPP Access
5B
To use the 3GPP function, in addition to previous section, you might need more information or
configuration to make this function work.
Note
That to use the 3GPP function, it strongly recommends to install the Networked Device
with a public and fixed IP address without any firewall protection.
RTSP Port:
Port 554 is the default for RTSP service. However, sometimes, some service providers change
this port number for some reasons. If so, user needs to change this port accordingly.
Dialing procedure:
1. Choose a verified player (PacketVideo or Realplayer currently)
2. Use the following URL to access:
rtsp://host/mpeg4/media.3gp
Where host is the host name or IP address of the camera.
Compatible 3G mobile phone:
Please contact your dealer to get the approved list of compatible 3G phone.
Note
Besides IP camera and 3G mobile phone. You will also need to make sure the
ISP and company has provided the 3GPP service to you.
79
Appendix D: Bandwidth and Video Size
Estimation
6B
The frame rate of video transmitted from the Internet camera depends on connection bandwidth
between client and server, video resolution, codec type, and quality setting of server. Here is a
guideline to help you roughly estimate the bandwidth requirements for your Internet camera.
The required bandwidth depends on content of video source. The slow motion video will produce
smaller bit rate generally and fast motion will produce higher bit rate vice versa. Actual results
generated by the Internet camera may be varying.
Image
Resolution
160 x 120
(QQVGA)
320 x 240
(QVGA)
640 x 480
(VGA)
1280x1024
(SXGA)
NOTE
Average range of data
sizes for M-JPEG mode
3 ~ 6k byte per frame
8 ~ 20k byte per frame
20 ~ 50K byte per frame
Average bit rate for
MPEG-4 mode
64kbps~256kbps
@ 30fps
256kbps~768kbps
@ 30fps
512kbps~2048kbps @
30fps
100 ~ 200k byte per
frame
NA
Average bit rate for
H.264 mode
32kbps~192kbps
@ 30fps
192kbps~512kbps
@ 30fps
384kbps~1536kbps
@ 30fps
512kbps~3076kbps
@ 15fps
Audio streaming also takes bandwidth around 5 kbps to 64kbps. Most xDSL/Cable
modem upload speeds may not even reach up to 128 kbps. Thus, you may not be able
to receive any video while streaming audio on a 128 kbps or lower connection. Even
though the upload speed is more than 128kbps, for optimal video performance,
disabling audio streaming will get better video performance.
80
Appendix E: DDNS Application
7B
1. Preface
If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or
other TCP/IP Service. Get your own domain like www.yourname.com, www.yourname.com.tw
etc. (Note: This domain must be registered with Internic via registration authorities such as
Network Solutions, DirectNIC, Register.com etc). Your domain name's dynamic IP address is
automatically tracked by a DDNS server.
Host your own Networked Device and much more no matter what your computer's IP address
may be and even if you have dialup, DSL or cable modem internet connection where your
computer's IP address changes all the time!! DDNS service supports all top level domain
names including but not limited to .com, .net, .org, .to, .uk etc.
2. Ethernet Network Environment
Normally, DDNS service is only necessary for the users that could only obtain dynamic IP
addresses. As to the users that could obtain the static valid IP address, they do not usually
have to apply the DDNS service. Before we decide if DDNS is necessary for the users, we
have to check what kind of Ethernet network environment we have to install our Networked
Device on.
(1) Environment of Fixed Valid IP Network
If users could obtain valid IP addresses, they could save the effort to apply DDNS service.
Because the IP address in this environment is fixed, users could input the IP address or
domain name of demo site directly in the IE browser.
(2) Environment of Dynamic IP Network
If users is under an environment of dynamic IP network (Dial-up xDSL), they have to apply a
domain name in advance. Then apply DDNS service. Finally setup the necessary information
of DDNS and PPPoE of the Networked Device in order to let the outside administrator be able
to access through internet.
3. Application Steps – DDNS & Domain Name
(1). Visit the following web site: http://www.dyndns.org/
(2). Click “Account”
HU
UH
81
(3). After the columns show up at the left side, click “Create Account”.
(4). Fill the application agreement and necessary information.
a. Username
b. E-mail address and confirmation
c. Password and confirmation
d. Submit all the input information and finish creating an account
82
Click these two options
(5). Check your e-mail mailbox. There will be an e-mail with a title “Your DynDNS Account
Information“. Click the hyperlink address to confirm the DDNS service that you just applied.
Then DDNS you applied activated.
Click to confirm
83
(6). Enter the web page http://www.dyndns.org/ again. Input your username and password
that you just applied to login administration interface of DDNS server.
HU
UH
Input your account
(7). If the correct username and password are input, you can see the following picture at the
top-right of the login page.
(8). Click the “Services”.
84
(9). Click the “ Dynamic DNS ”.
(10). Click the “Create Hosts”.
(11). We could create a domain name without any charge at this step. First, we input the host
name. (No.1) Then we pick a domain that is easy to remember. Finally (No.2), click the “Add
Host” to submit the domain name information. (No.3)
1
3
2
4. Setup the DDNS and PPPoE of Network Device
At last, users have to enter the web page of Networked Device and setup the necessary
information of DDNS and PPPoE after the application of DDNS service. Please check the user
manual to access the DDNS and PPPoE pages. After saving the modification, restart the
device. The external users could browse the Networked Device by the input of their domain
name.
85
Appendix F:
Configure Port Forwarding Manually
8B
The device can be used with a router. If the device wants to be accessed from the WAN, its IP
address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function
of router needs to be setup. This device supports UPnP traversal function. Therefore, user could
use this feature to configure port forwarding of NAT router first. However, if user needs to
configure port forwarding manually, please follow the steps as below:
Manually installing the device with a router on your network is an easy 3–step procedure as
following:
1. Assign a local/fixed IP address to your device
2. Access the Router with Your Web browser
3. Open/Configure Virtual Server Ports of Your Router
1. Assign a local/fixed IP address to your device
The device must be assigned a local and fixed IP Address that allows it to be recognized by the
router. Manually setup the device with a fixed IP address, for example, 192.168.0.100.
2. Access the Router with Your Web browser
The following steps generally apply to any router that you have on your network. The PLANET
WNRT-620 is used as an example to clarify the configuration process. Configure the initial settings
of the router by following the steps outlined in the router’s Quick Installation Guide.
If you have cable or DSL service, you will most likely have a dynamically assigned WAN IP
Address. ‘Dynamic’ means that your router’s WAN IP address can change from time to time
depending on your ISP. A dynamic WAN IP Address identifies your router on the public network
and allows it to access the Internet. To find out what your router’s WAN IP Address is, go to the
Status screen on your router and locate the WAN information for your router. As shown on the
following page the WAN IP Address will be listed. This will be the address that you will need to
type in your web browser to view your camera over the Internet. Be sure to uncheck the Reset IP
address at next boot button at the top of the screen after modifying the IP address. Failure to do
so will reset the IP address when you restart your computer.
86
Your WAN IP Address will be listed here.
3. Open/set Virtual Server Ports to enable remote image viewing
The firewall security features built into the router and most routers prevent users from accessing
the video from the device over the Internet. The router connects to the Internet over a series of
numbered ports. The ports normally used by the device are blocked from access over the Internet.
Therefore, these ports need to be made accessible over the Internet. This is accomplished using
the Virtual Server function on the router. The Virtual Server ports used by the camera must be
opened through the router for remote access to your camera.
Follow these steps to configure your router’s Virtual Server settings
z
Click Enabled.
z
Enter a unique name for each entry.
z
Select Both under Protocol Type (TCP and UDP)
z
Enter your camera’s local IP Address (e.g., 192.168.0.100, for example) in the Private
IP field.
z
If you are using the default camera port settings, enter 80 into the Public and
Private Port section, click Add.
A check mark appearing before the entry name will indicate that the ports are enabled.
NOTE
Some ISPs block access to port 80. Be sure to check with your ISP so that you can
open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you
will need to change the port the camera uses from 80 to something else, such as 8080.
Not all routers are the same, so refer to your user manual for specific instructions on
how to open ports.
87
Enter valid ports in the Virtual Server section of your router. Please make sure to check the box
on this line to enable settings. Then the device can be access from WAN by the router’s WAN IP
Address.
By now, you have finished your entire PC configuration for this device.
88
Appendix G:
9B
Troubleshooting & Frequently Asked Questions
Features
The video and audio codec is
adopted in the device.
The device utilizes H.264, MPEG-4 and M-JPEG triple compression
to providing high quality images. Where H.264 and MPEG-4 are
standards for video compression and M-JPEG is a standard for
image compression.
The audio codec is defined as AMR for 3GPP and G.711/G.726 for
RTSP streaming.
The maximum number of user
accesses the device
simultaneously.
The maximum number of users is limited to 20. However, it also
depends on the total bandwidth accessed to this device from clients.
The maximum data throughput of the device is around 20~25Mbps
for UDP mode and 10Mbps for HTTP mode. Therefore, the actual
number of connected clients is varying by streaming mode, settings
of resolution, codec type, frame rate and bandwidth. Obviously, the
performance of the each connected client will slow down when many
users are logged on.
The device can be used outdoors
or not.
The device is not weatherproof. It needs to be equipped with a
weatherproof case for outdoors using. However, equipped with a
weatherproof case might disable the audio function of the device.
Install this device
Status LED does not light up.
z
Check and confirm that the DC power adaptor, included in
packaged, is used. Secure the power connector and re-power it
on again.
z
If the problem is not solved, the device might be faulty. Contact
your dealer for further help.
The network cabling is required for
the device.
The device uses Category 5 UTP cable allowing 10 and/or 100
Base-T networking.
The device will be installed and
work if a firewall exists on the
network.
If a firewall exists on the network, port 80 is open for ordinary data
communication. The HTTP port and RTSP port need to be opened
on the firewall or NAT router.
The username and password for
the first time or after factory default
reset
Username = admin and leave password blank.
Forgot the username and
password
Note that it’s all case sensitivity.
Follow the steps below.
1. Restore the factory default setting by press pressing and holding
down more than 3 seconds on the device.
89
2. Reconfigure the device.
Forgot the IP address of the
device.
Check IP address of device by using the IPWizard program or by
UPnP discovery or set the device to default by Reset button.
IPWizard program cannot find the
device.
z
Re-power the device if cannot find the unit within 1 minutes.
z
Do not connect device over a router. IPWizard program cannot
detect device over a router.
z
If IP address is not assigned to the PC which running IPWizard
program, then IPWizard program cannot find device. Make sure
that IP address is assigned to the PC properly.
z
Antivirus software on the PC might interfere with the setup
program. Disable the firewall of the antivirus software during
setting up this device.
z
Check the firewall setting of your PC or Notebook.
Internet Explorer does not seem to
work well with the device
Make sure that your Internet Explorer is version 6.0 or later. If you
are experiencing problems, try upgrading to the latest version of
Microsoft’s Internet Explorer from the Microsoft webpage.
IPWizard program fails to save the
network parameters.
Network may have trouble. Confirm the parameters and connections
of the device.
UPnP NAT Traversal
Can not work with NAT router
Maybe NAT router does not support UPnP function. Please check
user’s manual of router and turn on UPnP function.
Some IP cameras are working but
others are failed
Maybe too many IP cameras have been installed on the LAN, and
then NAT router is out of resource to support more cameras. You
could turn off and on NAT router to clear out of date information
inside router.
Access this device
Cannot access the login page and
other web pages of the Network
Camera from Internet Explorer
z
Maybe the IP Address of the Network Camera is already being
used by another device or computer. To confirm this possible
problem, disconnect the Network Camera from the network first,
and then run the PING utility to check it out.
z
Maybe due to the network cable. Try correcting your network
cable and configuration. Test the network interface by connecting
a local computer to the Network Camera via a crossover cable.
z
Make sure the Internet connection and setting is ok.
z
Make sure enter the IP address of Internet Explorer is correct. If
the Network Camera has a dynamic address, it may have
changed since you last checked it.
z
Network congestion may prevent the web page appearing
quickly. Wait for a while.
90
The IP address and Subnet Mask of the PC and Network Camera
must be in the same class of the private IP address on the LAN.
Image or video does not appear in
the main page.
How to check the device’s ActiveX
is installed on your computer
Internet Explorer displays the
following message: “Your current
security settings prohibit
downloading ActiveX controls”.
The device work locally but not
externally.
z
Make sure the http port used by the Network Camera, default=80,
is forward to the Network Camera’s private IP address.
z
The port number assigned in your Network Camera might not be
available via Internet. Check your ISP for available port.
z
The proxy server may prevent you from connecting directly to the
Network Camera, set up not to use the proxy server.
z
Confirm that Default Gateway address is correct.
z
The router needs Port Forwarding feature. Refer to your router's
manual for details.
z
Packet Filtering of the router may prohibit access from an
external network. Refer to your router's manual for details.
z
Access the Network Camera from the Internet with the global IP
address of the router and port number of Network Camera.
z
Some routers reject the global IP address to access the Network
Camera on the same LAN. Access with the private IP address
and correct port number of Network Camera.
z
When you use DDNS, you need to set Default Gateway and DNS
server address.
z
If it’s not working after above procedure, reset Network Camera
to default setting and installed it again.
z
The first time the PC connects to Network Camera, a pop-up
Security Warning window will appear to download ActiveX
Controls. When using Windows XP, or Vista, log on with an
appropriate account that is authorized to install applications.
z
Network congestion may prevent the Image screen from
appearing quickly. You may choose lower resolution to reduce
the required bandwidth.
Go to C:\Windows\Downloaded Program Files and check to see if
there is an entry for the file “IPCamera Control”. The status column
should show “Installed”. If the file is not listed, make sure your
Security Settings in Internet Explorer are configured properly and
then try reloading the device’s home page. Most likely, the ActiveX
control did not download and install correctly. Check your Internet
Explorer security settings and then close and restart Internet
Explorer. Try to browse and log in again.
Setup the IE security settings or configure the individual settings to
allow downloading and scripting of ActiveX controls.
z
Might be caused from the firewall protection. Check the Internet
firewall with your system or network administrator. The firewall
may need to have some settings changed in order for the device
91
to be accessible outside your LAN.
z
Make sure that the device isn’t conflicting with any other web
server running on your LAN.
z
Check the configuration of the router settings allow the device to
be accessed outside your local LAN.
z
Check the bandwidth of Internet connection. If the Internet
bandwidth is lower than target bit rate, the video streaming will
not work correctly.
The unreadable characters are
displayed.
Use the operating system of the selected language. Set the
Encoding or the Character Set of the selected language on the
Internet Explorer.
Frame rate is slower than the
setting.
z
The traffic of the network and the object of the image affect the
frame rate. The network congestion causes frame rate slower
than the setting.
z
Check the bandwidth of Internet connection. If the Internet
bandwidth is lower than target bit rate, the video streaming will
not work correctly.
z
Ethernet switching hub can smooth the frame rate.
z
Your connection to the device does not have enough bandwidth
to support a higher frame rate for the streamed image size. Try
reducing the video streaming size to 160x120 or 320x240 and/or
disabling audio.
z
Audio will consume 32 kbps. Disable audio to improve video.
Your Internet connection may not have enough bandwidth to
support streaming audio from the device.
z
Default Gateway and DNS server address should be set up
correctly.
z
If FTP does not work properly, ask your ISP or network
administrator about the transferring mode of FTP server.
Blank screen or very slow video
when audio is enabled.
Image Transfer on e-mail or FTP
does not work.
Video quality of the device
The focus on the Camera is bad.
The lens is dirty or dust is attached. Fingerprints, dust, stain, etc. on
the lens can degrade the image quality.
The color of the image is poor or
strange.
z
Adjust White Balance.
z
To insure the images you are viewing are the best they can be,
set the Display property setting (color quality) to 16bit at least and
24 bit or higher if possible within your computer.
z
The configuration on the device image display is incorrect. You
need to adjust the image related parameters such as brightness,
contrast, hue and sharpness properly.
z
Wrong power line frequency makes images flicker. Make sure the
Image flickers.
92
50 or 60Hz format of your device.
z
If the object is dark, the image will flicker. Make the condition
around the Camera brighter.
Miscellaneous
Can not play the recorded ASF file
Please installed Microsoft®’s DirectX 9.0 or later and uses the
Windows Media Player 11.0 or later to play the AVI filed recorded by
the Device.
93
Appendix H: Product Specification
10B
Product
ICA-HM351
Video Specification
Image Sensor
1/2.7“ 2 Mega-pixel Progressive CMOS
Lens
4mm fixed lens with Fixed Iris
Sensitivity
0.5 Lux @ F1.4
View Angle
H: 66 Degree / V: 52 Degree
Video Encoder
H.264 / MPEG-4 / M-JPEG
Rate Control
CBR (Constant Bit Rate) / VBR (Variable Bit Rate)
Video Resolution
1920 x 1080 / 1280 x 720 / 640 x 360 / 320 x 180 / 160 x 90
Frame Rate
Up to 30fps for all resolutions (2M Real-time)
Image Control
AE, AWB
3D Noise reduction
Color, Brightness, Sharpness, Contrast, Hue
Mirror/Flip
8 Privacy Masks
Text, time and date overlay
Audio Specification
Audio Codec
RTSP: G.711 64kbps, G.726 32kbps
3GPP: AMR
Audio Streaming
One-Way or Two-Way
Microphone(Audio Input)
External microphone input, Phone Jack
Audio Output
Adjustable audio output gain, Phone Jack
Network and Configuration
Network Interface
1 x RJ-45
Network Standard
IEEE 802.3 / IEEE 802.3u / IEEE 802.3af
Network Protocol
IPv4, TCP, UDP, HTTP, HTTPS, SMTP, FTP, NTP, DNS, DDNS, DHCP, DIPS,
ARP, Bonjour, UPnP, RTSP, RTP, RTCP, IGMP, PPPoE, 3GPP, Samba, ICMP
Browser / Software
Microsoft ® Internet Explorer 6.0 or later
PLANET Cam Viewer 3 Lite/Pro
Motion Detection
10 areas definable
Environment Specifications
Power Requirement
PoE
12V DC, 1A
IEEE 802.3af
(PoE is for IP cam & IR LED only, Heater & fan require external adaptor 12V/1A)
Dimension (W x D x H)
141 x 310 x 120 mm
Weight
Power Consumption
1335 g
Max. 8W for camera and IR LEDs
Max. 5W for heater only
94
Illumination LED
Heater & Fan
Protection Class
88pcs IR LED, 35M IR Distance
Heater
ON: 15 Degree C
OFF:25 Degree C
Blower
ON: 37 Degree C
OFF:25 Degree C
IP-66 classification with Weather proof
Operating Temperature
-30 ~ 60 Degree C
Operating Humidity
0 ~ 95% (non-condensing)
Emission
CE, FCC
95
Download PDF