User Manual

Snapshot
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
Auto-ranging
Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle
User Manual
3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
TABLE OF CONTENTS
1. BEFORE YOU BEGIN ....................................................................................................................................................... 3 WHAT IS INCLUDED ................................................................................................................................................................................ 3 UNPACKING INSTRUCTIONS .................................................................................................................................................................... 3 MANUAL CONVENTIONS ......................................................................................................................................................................... 3 ICONS .................................................................................................................................................................................................. 3 SAFETY INSTRUCTIONS .......................................................................................................................................................................... 4 2. INTRODUCTION ............................................................................................................................................................... 5 FEATURES ............................................................................................................................................................................................ 5 PRODUCT OVERVIEW ............................................................................................................................................................................ 6 3. SETUP ............................................................................................................................................................................... 7 AC POWER........................................................................................................................................................................................... 7 Power Linking ............................................................................................................................................................... 7 MOUNTING ........................................................................................................................................................................................... 7 Orientation .................................................................................................................................................................... 7 Rigging .......................................................................................................................................................................... 7 4. OPERATING INSTRUCTIONS.......................................................................................................................................... 8 CONFIGURING THE STARTING ADDRESS .................................................................................................................................................. 8 DMX OPERATION ................................................................................................................................................................................. 8 MASTER/SLAVE .................................................................................................................................................................................... 8 STANDALONE OPERATION ...................................................................................................................................................................... 9 Automatic ...................................................................................................................................................................... 9 Sound-Active................................................................................................................................................................. 9 Custom Program ........................................................................................................................................................... 9 DMX CHANNEL VALUES ...................................................................................................................................................................... 10 DIP SWITCH VALUES........................................................................................................................................................................... 10 5. APPENDIX....................................................................................................................................................................... 11 DMX PRIMER ..................................................................................................................................................................................... 11 GENERAL MAINTENANCE ..................................................................................................................................................................... 11 DATA CABLING .................................................................................................................................................................................... 12 DMX Data Cable ......................................................................................................................................................... 12 Cable Connectors ....................................................................................................................................................... 12 FIXTURE LINKING ................................................................................................................................................................................ 12 3-Pin to 5-Pin Conversion Chart ................................................................................................................................. 13 Setting up a DMX Serial Data Link ............................................................................................................................. 13 SETTING THE STARTING ADDRESS ........................................................................................................................................................ 14 GENERAL TROUBLESHOOTING .............................................................................................................................................................. 14 CONTACT US ...................................................................................................................................................................................... 14 RETURNS PROCEDURE ........................................................................................................................................................................ 15 CLAIMS .............................................................................................................................................................................................. 15 TECHNICAL SPECIFICATIONS ................................................................................................................................................................ 16 CHAUVET®, 2010, All Rights Reserved Information and specifications in this User Manual are subject to change without notice. CHAUVET® assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. 1. BEFORE YOU BEGIN
What is included
¾
¾
¾
¾
1 x Trident™
1 x Power Cable
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information from
the regular text.
MEANING
CONVENTION
[10]
<Menu>
1~512
50/60
Settings
MENU > Settings
ON
A DIP switch to be configured
A key to be pressed on the fixture’s control panel
A range of values
A set of values of which only one can be chosen
A menu option not to be modified (for example, showing the operating
mode/current status)
A sequence of menu options to be followed
A value to be entered or selected
Icons
This manual uses the following icons to indicate information that requires special attention on the part
of the user.
MEANING
ICONS
This paragraph contains critical installation, configuration or operation
information. Failure to comply with this information may render the fixture
partially or completely inoperative, cause damage to the fixture or cause
harm to the user.
This paragraph contains important installation or configuration information.
Failure to comply with this information may prevent the fixture from
functioning correctly.
This paragraph reminds you of useful, although not critical, information.
1. Before You Begin
3
7/6/2010 9:17 AM
Safety Instructions
Please read these instructions carefully. It includes important
information about the installation, usage and maintenance of this
product.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1. Before You Begin
Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to
rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing fuse and be sure to replace with
same fuse source.
Secure fixture to fastening device using a safety chain.
Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher
than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.
Avoid direct eye exposure to the light source while it is on.
4
7/6/2010 9:17 AM
2. INTRODUCTION
Features
•
•
•
•
•
3-channel DMX-512 LED centerpiece
Individual control of red, green and blue
Variable electronic strobe in any color combination
Back-and-forth motor effect with variable speed
Static colors with or without DMX controller
Ad d i t i o n a l F e a t u r e s
•
•
•
•
Built-in automated programs
Built-in sound activated programs
Tri-color LEDs (2,550 mA total)
Additional power output: max 26 units
2. Introduction
5
7/6/2010 9:17 AM
Product Overview
Hanging bracket
Fuse holder
Back Panel A
Safety attachment
point
Power in
Power out
DMX in
Back Panel B
DMX out
Microphone
DIP switches
Microphone
sensitivity
adjustment knob
2. Introduction
6
7/6/2010 9:17 AM
3. SETUP
AC Power
This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage
to which you are connecting it is within the range of accepted voltages.
Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0
to 100% switch.
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its
average current draw under normal conditions.
Always connect the fixture to a circuit with a suitable electrical ground.
Power Linking
This fixture contains power linking via the edison outlet located next to the power input cable. Please
see the diagram below for further explanation.
The maximum quantity of fixtures that may be linked is 26.
Fixture 1
Fixture 2
Fixture 3
Additional power
link out
Mounting
Orientation
The Trident™ may be mounted in any safe position, provided there is adequate room for ventilation.
Rigging
Be sure that the structure can support the weight of the fixture. Please see the “Technical
Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. This
may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13 mm in
size. When rigging consider routine maintenance and control panel access. Please see the following
steps for installation.
•
•
•
3. Setup
If the power link out is intended to be used with multiple fixture, take into account the length
of each power cable, and mount the fixtures close enough to one another to accommodate
for this.
When aiming the fixture, you may use the bracket adjustment knobs (2x). Loosen each
knob, adjust to the desired angle, and then tighten both knobs by turning clockwise. Do not
use tools for this step, as it may cause damage.
Safety cables must always be used.
7
7/6/2010 9:17 AM
4. OPERATING INSTRUCTIONS
Configuring the Starting Address
Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for
control begins to read the data on the channel indicated by the starting address. For example, a
fixture that uses seven DMX channels and is addressed to start on DMX channel 100, will read data
from channels: 100, 101, 102, 103, 104, 105 and 106. Choose the starting addresses for each fixture
so that the channels used do not overlap. In addition, you should note the starting address selected
for future reference.
The Trident™ fixture uses 3 DMX channels. If this is your first time using DMX, we recommend
reading the “DMX Primer” section in the “Appendix”.
DMX Operation
This is the operating mode which will allow for control with an external DMX controller. You must set the starting
address for this mode. If this is your first time using DMX, then it is recommended that you refer to the “DMX
Primer” section in the “Appendix” of this manual.
1.
2.
3.
4.
Plug the fixture into power.
Connect DMX cable(s) to controller.
Turn DIP switch [10] to the ON position.
Use DIP switches 1~9 to set the starting address.
Master/Slave
This is the operating mode which will allow 1 fixture to act as the “master” and control all of the other “slave”
fixtures. You must set both the master and the slave(s) fixtures to the correct mode for this operation. They
must also be connected using DMX cables, in a daisy chain fashion.
Master Settings:
1.
Using the DIP switches, set the master fixture to one of the following modes: custom, automatic,
or sound-activated.
Slave Settings:
1.
2.
Turn DIP switch [10] to the ON position.
Turn DIP switches 1~9 to the OFF position.
Do not connect a DMX controller to the daisy chain for this operation.
Only one fixture may be set to master in the DMX daisy chain.
4. Operating Instructions
8
7/6/2010 9:17 AM
Standalone Operation
Automatic
This fixture has a preprogrammed chase. This is accessed via the DIP switches. Please see the
instructions below for further explanation.
1.
2.
3.
Plug the fixture into power.
Turn DIP switch [8] to the ON position.
Turn all other DIP switches to the OFF position.
Do not connect a DMX controller to the daisy chain for this operation.
Sound-Active
This fixture has a preprogrammed sound triggered chase. This is accessed via the DIP switches, and the
speed may be adjusted using the audio adjustment knob. Please see the instructions below for further
explanation.
1.
2.
3.
Plug the fixture into power.
Turn DIP switch [9] to the ON position.
Turn all other DIP switches to the OFF position.
Do not connect a DMX controller to the daisy chain for this operation.
Custom Program
This fixture has individual control over each of the following functions via DIP switches: color, strobe, and
motor rotation. These functions may be combined in any combination. Please see the instructions below
for further explanation.
1.
2.
3.
4.
5.
Plug the fixture into power.
Turn DIP switches [8] ~ [10] to the OFF position.
DIP switches [1] ~ [3] control the color. These may be combined.
DIP switches [4] ~ [6] control the strobe speed. Only 1 of these may be selected at a time.
Turning them all to the OFF position allows the color to remain on constant.
DIP switch [7] controls the motor rotation. Turning this to the ON position will cause the motor to
rotate CW/CCW at a preset speed. This may not be altered.
Do not connect a DMX controller to the daisy chain for this operation.
4. Operating Instructions
9
7/6/2010 9:17 AM
DMX Channel Values
CHANNEL
VALUE
FUNCTION
1
000 Ù 004
005 Ù 028
029 Ù 056
057 Ù 084
085 Ù 112
113 Ù 140
141 Ù 168
169 Ù 197
198 Ù 224
225 Ù 255
Color Selection (no dimming)
Blackout
Red
Green
Blue
Green/Blue
Red/Blue
Red/Green
Red/Green/Blue
3-color chase
7-color chase
2
000 Ù 004
005 Ù 255
Strobe
No function
Strobe (slow Ù fast)
3
000 Ù 127
128 Ù 255
Rotation
Indexing
Rotate (fast to slow)
DIP Switch Values
FUNCTIONS
DIP SWITCHES
Red
Green
Blue
Strobe (slow)
Strobe (medium)
Strobe (fast)
Motor
Automatic
Sound-activated
DMX /Slave
1
2
3
4
5
6
7
8
9
10
4. Operating Instructions
NOTES & DESCRIPTION
Combine these DIP switches to trigger simultaneously
Only 1 of these may be selected at a time
ON = bi-directional rotation
Overrides DIP switches 1~6
Overrides DIP switches 1~6
DMX mode/Slave mode activation
10
7/6/2010 9:17 AM
5. APPENDIX
DMX Primer
There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture
capable of receiving DMX will require one or a number of sequential channels. The user must assign
a starting address on the fixture that indicates the first channel reserved in the controller. There are
many different types of DMX controllable fixtures and they all may vary in the total number of
channels required. Choosing a start address should be planned in advance. Channels should never
overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set
incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
•
•
Unplug fixture from power.
Use a vacuum or air compressor and a soft brush to remove dust collected on external
vents.
•
Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl
Alcohol and a soft lint free cotton cloth or lens tissue.
•
Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
•
Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky
or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean
with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days.
Clean the fixture at least every 30/60 days.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
5. Appendix
11
7/6/2010 9:17 AM
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX Data Cable
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable must
have the following characteristics:
Type:
shielded, 2-conductor twisted pair
Maximum capacitance between conductors:
30 pF/ft
Maximum capacitance between conductor and shield:
55 pF/ft
Maximum resistance:
20 ohms/1000 ft
Nominal impedance:
100 ~ 140 ohms
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
1
3
2
DMX connector configuration
COMMON
1
3
2
INPUT
1
3
2
DMX +
DMX
-
120 ohm ¼ W
resistor between
pin 2 (DMX -) and
pin 3 (DMX +) on
the output of the
last fixture
OUTPUT
To avoid signal transmission problems
and interference, it is always advisable to
connect a DMX signal terminator.
Do not allow contact between the common and the fixture’s chassis ground. Grounding the
common can cause a ground loop, and your fixture may perform erratically. Test cables with
an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted
to the shield or each other.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures
the data link can support.
Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA485 standard, no more than 32 fixtures should be connected on one data link. Connecting
more than 32 fixtures on one serial data link without the use of a DMX optically-isolated
splitter may result in deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32
5. Appendix
12
7/6/2010 9:17 AM
3-Pin to 5-Pin Conversion Chart
If you use a controller with a 5-pin DMX output connector, you will need to use a 5pin to 3-pin adapter. The chart below details a proper cable conversion:
3-PIN TO 5-PIN CONVERSION CHART
Conductor
3-Pin Female (Output)
5-Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - ) signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Not used
Pin 4
Not used
Pin 5
Setting up a DMX Serial Data Link
Universal DMX Controller
1. Connect the (male) 3-pin connector side of
the DMX cable to the output (female) 3-pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female)
3-pin connector to the input connector of the
next fixture consisting of a (male) 3-pin
connector.
This drawing
provides a general
illustration of the
DMX input/output
panel of a lighting
fixture.
3. Then, proceed to connect from the output as
stated above to the input of the following
fixture and so
Continue the link
5. Appendix
13
7/6/2010 9:17 AM
Setting the Starting Address
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a start address
from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that uses six DMX channels and was addressed to start
on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start
addresses so that the channels used do not overlap, and note the start address selected for future reference.
If this is your first time addressing a fixture using the DMX control protocol, we suggest jumping to the
“Appendix” section and reading the heading “DMX Primer”. It contains very useful information that will help you
understand its use.
General Troubleshooting
SYMPTOM
POSSIBLE CAUSE(S)
Breaker/Fuse
keeps blowing
Device does not
power up
Fixture is not
responding to
DMX
Loss of signal
POSSIBLE ACTION(S)
• Excessive circuit load
• Check total load placed on the electrical circuit.
• Short circuit along the power
wires
• Check for a short in the electrical wiring (internal and/or
external)
• No power
• Check for power on power outlet
• Loose power cord
• Check power cord
• Wrong DMX addressing
• Check Control Panel and unit addressing
• Damaged DMX cables
• Check DMX cables
• Wrong polarity settings on the
controller
• Check polarity switch settings on the controller
• Loose DMX cables
• Check cable connections
• Faulty DMX interface
• Replace DMX input
• Faulty Main PCB
• Replace Main PCB
• Non DMX cables
• Use only DMX compatible cables
• Bouncing signals
• Install terminator as suggested
• Long cable / Low level signal
• Install amplifier right after fixture with strong signal
• Too many fixtures
• Install an optically coupled DMX splitter after unit #32
• Interference from AC wires
• Keep DMX cables separated from power cables or
black lights
If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support.
Contact Us
World Wide
5. Appendix
General Information
CHAUVET
th
3000 North 29 Court
Hollywood, FL 33020
voice: 954.929.1115
fax:
954.929.5560
toll free: 800.762.1084
Technical Support
CHAUVET
th
3000 North 29 Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax:
954.929.5560 (Attention: Service)
World Wide Web
www.chauvetlighting.com
14
7/6/2010 9:17 AM
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #).
Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to pack fixture properly; any shipping damage resulting from
inadequate packaging is the customer’s responsibility. As a suggestion, proper UPS packing or
double-boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of paper inside
the box:
1)
Your name
2)
Your address
3)
Your phone number
4)
The RMA #
5)
A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
5. Appendix
15
7/6/2010 9:17 AM
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................... 10.5 in (269 mm)
Width ............................................................................................................................ 12.1 in (308 mm)
Height ........................................................................................................................... 13.7 in (348 mm)
Weight ................................................................................................................................. 8 lbs (3.6 kg)
POWER
Auto-ranging Power Supply ............................................................................... 100~240 VAC, 50/60 Hz
Power Consumption @ 120 VAC, 60 Hz................................................ 16 W (0.3 A) max, 0.1 A inrush
Power Consumption @ 230 VAC, 50 Hz................................................ 16 W (0.2 A) max, 0.2 A inrush
Power output ....................................................................................................................... 26 units max
Fuse...................................................................................................................................... F 2 A, 250 V
LIGHT SOURCE
LED.......................................................................................................... 2, 3 W (850 mA x3) 50,000 hrs
PHOTO OPTIC
Coverage Angle ................................................................................................................................ 155°
THERMAL
Maximum ambient temperature .........................................................................................104° F (40° C)
CONTROL & PROGRAMMING
Data input ................................................................................................ locking 3-pin XLR male socket
Data output ........................................................................................... locking 3-pin XLR female socket
Data pin configuration .............................................................................. pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................................ DMX-512 USITT
DMX Channels ....................................................................................................................................... 3
ORDERING INFORMATION
Trident™ ................................................................................................................................... TRIDENT
WARRANTY INFORMATION
Warranty .............................................................................................................. 2-year limited warranty
Technical Specifications
16
7/6/2010 9:17 AM
Download PDF