EKI-2701PSI
Industrial PoE Splitter, Wide
Temperature
User Manual
Copyright
The documentation and the software included with this product are copyrighted 2007 by
Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make
improvements in the products described in this manual at any time without notice. No part of
this manual may be reproduced, copied, translated or transmitted in any form or by any
means without the prior written permission of Advantech Co., Ltd. Information provided in this
manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, nor for any infringements of the rights of third parties, which may
result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Part No.
Printed in China
EKI-2701PSI User Manual_ed1
1st Edition
February 2008
ii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by persons
other than repair personnel authorized by Advantech, or which have been subject to misuse,
abuse, accident or improper installation. Advantech assumes no liability under the terms of
this warranty as a consequence of such events.
Because of Advantech′s high quality-control standards and rigorous testing, most of our
customers never need to use our repair service. If an Advantech product is defective, it will be
repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you
will be billed according to the cost of replacement materials, service time and freight. Please
consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU speed,
Advantech products used, other hardware and software used, etc.) Note anything
abnormal and list any onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product, and any
helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement Order
Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable
container. A product returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to your
dealer.
iii
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions for
passing included the equipment being operated within an industrial enclosure. In order to
protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage,
we strongly recommend the use of CE-compliant industrial enclosure products.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Technical Support and Assistance
Step 1.
Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Step 2.
Contact your distributor, sales representative, or Advantech’s customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, application software,
etc.)
- A complete description of the problem
- The exact wording of any error messages
EKI-2701PSI User Manual_ed1
iv
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not
use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and
must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may
cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by
qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user's
manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE
TEMPERATURE MAY GO BELOW -40 ℃ (-40℉) OR ABOVE 85 ℃ (185 ℉ ). THIS
COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.
v
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from damage.
1. To avoid electrical shock, always disconnect the power from your PC chassis before you
work on it. Don't touch any components on the CPU card or other cards while the PC is
on.
2. Disconnect power before making any configuration changes. The sudden rush of power
as you connect a jumper or install a card may damage sensitive electronic components.
EKI-2701PSI User Manual_ed1
vi
Chapter 1
Contents
Overview........................................... 2
1.1 Introduction ......................................................... 2
1.1.1 Flexible Mounting ...................................... 2
1.1.2 Advanced Protection ................................. 2
1.1.3 Wide Operating Temperature .................... 2
1.2 Features.............................................................. 3
1.3 Specification ....................................................... 4
1.4 Packing List ........................................................ 6
1.5 Safety Precaution ............................................... 6
Chapter 2
Installation........................................ 8
2.1 LED Indicators .................................................... 8
Table 2.1: EKI-2701PSI LED Definition ......................8
2.2 Dimensions (units: mm) ...................................... 9
Figure 2.1: Front View of EKI-2701PSI series .............9
Figure 2.2: Side View of EKI-2701PSI series.............10
Figure 2.3: Rear View of EKI-2701PSI series ............11
Figure 2.4: Top View of EKI-2701PSI series .............12
2.3 Mounting ........................................................... 13
2.3.1 Wall mounting.......................................... 13
Figure 2.5: Combine the Metal Mounting Kit (units:
mm)..............................................................................13
2.3.2 DIN-rail Mounting..................................... 14
Figure 2.6: Installation to DIN-rail Step 1...................14
Figure 2.7: Installation to DIN-rail Step 2...................15
2.4 Network Connection ......................................... 16
2.5 Power Connection ............................................ 17
Figure 2.13: Pin Assignment of the Power Connector 17
Chapter 3 Troubleshooting ............................ 20
Appendix A Pin Assignment & Wiring ........... 22
Figure A.1: RJ-45 Pin Assignment..............................22
Figure A.2: EIA/TIA-568B .........................................22
Figure A.2: EIA/TIA-568A .........................................23
vii
Contents
EKI-2701PSI User Manual_ed1
viii
CHAPTER
Overview
Sections include:
z
Introduction
z
Features
z
Specifications
z
Packing List
z
Safety Precaution
1
Chapter1
Chapter 1
Overview
1.1 Introduction
With the technology of PoE (Power over Ethernet), we can transfer both data and
electrical power to Ethernet-enabled devices using a standard Ethernet CAT5 cable,
EKI-2701PSI plays the role of powered device (PD) and splits power from PoE to
Ethernet devices. In this case, both power and data can be transmitted up to 328 feet
(100m) from power source equipment (PSE).
This product can operate in a wide range of temperature between -40 and 75oC, and
the rugged hardware design makes EKI-2701PSI perfect to ensure your PoE Ethernet
equipment can meet industrial applications demanding.
1.1.1
Flexible Mounting
EKI-2701PSI is compact and can be mounted on a DIN-rail or a panel, so it is suitable
for any space-constrained environment.
1.1.2
Advanced Protection
The power line of EKI-2701PSI supports up to 3,000 VDC EFT protection, which secure
equipment against unregulated voltage and make systems safer and more reliable.
Meanwhile, 6,000 VDC ESD protections for Ethernet ports make EKI-2701PSI more
suitable for harsh environments.
1.1.3
Wide Operating Temperature
The operating temperature of the EKI-2701PSI is between -40 ~ 75oC. With such a
wide range, you can use the EKI-2701PSI in some of the harshest industrial
environments that exist.
EKI-2701PSI User Manual_ed1
2
1.2 Features
•
•
•
•
•
•
•
•
•
•
Supports 10/100/1000T for PoE in and Data out
Power Isolation and Short circuit protection for power output
Auto disconnection for over power voltage input
Supports output power up to 12.95W at 24VDC
Wide-range Power Design
Supports surge (EFT) protection 3,000 VDC for power line
Supports 4,000 VDC Ethernet ESD protection
Provides flexible mounting: DIN-rail, Wall Mounting
IP-30 Protection
Supports operating temperatures from -40 ~ 75 ℃
3
Chapter1
1.3 Specification
Communications
IEEE 802.3, 802.3u, 802.3ab, 802.3af
10/100Base-TX, 1000Base-T
Up to 100 meters (UTP)
Up to 1000 Mbps
Store and Forward
Standard
LAN
Transmission Distance
Transmission Speed
Switch Architecture
Interface
2 x 10/100/1000Base-T RJ-45 ports
6-pin removable screw terminal (power output)
TX port: 10/100/1000M, Link/Active
Fiber port: LNK/ACT
Port Alarm, LFP
Connectors
LED Indicators
Power
44 ~ 57VDC
17.76W at 48VDC
12.95W Max. (0.539A @ 24VDC)
Power Input
Power Consumption
Power Output
Mechanism
37 x 95 x 140 mm
IP30, Metal shell with solid mounting kits
DIN-rail, wall
Dimensions (W x D x H)
Enclosure
Mounting
Protection
4,000 VDC
3,000 VDC
0.539A@24VDC
ESD (Ethernet)
Surge (EFT for power)
Overload current protection
Environment
-40 ~ 75oC (-40 ~ 167oF)
-40 ~ 85oC (-40 ~ 185oF)
5 ~ 95% (non-condensing)
0 ~ 95% (non-condensing)
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
EKI-2701PSI User Manual_ed1
4
Certifications
UL, 60950-1, CAN/CSA-C22.2 No.60950
U.S.A.: FCC Part 15 CISPR 22
EU: EN55011, EN61000-6-4
EN55022, Class A,
EN61000-3-2/3
EN55024
IEC61000-4-2/3/4/6/8
EN61000-6-2/4
IEC60068-2-32
IEC60068-2-27
IEC60068-2-6
Safety
EMC
Free Fall
Shock
Vibration
5
Chapter1
1.4 Packing List
•
•
•
•
•
1 x EKI-2701PS Series Industrial PoE Splitter
1 x eAutomation Industrial Communication CD-ROM with software, and User manual
2 x Panel Mounting Bracket and Screws
1 x DIN-rail Mounting Bracket and Screws
1 x EKI-2701PSI Startup Manual
1.5 Safety Precaution
Attention
IF DC voltage is supplied by an external circuit, please use a protection device
on the power supply input.
EKI-2701PSI User Manual_ed1
6
CHAPTER
Installation
Sections include:
z
LED Indicators
z
Dimensions
z
Mounting
z
Network Connection
z
Power Connection
7
Chapter2
Chapter 2
Installation
In this chapter, you will be given an overview of the EKI-2701PSI hardware installation
procedures.
2.1 LED Indicators
There is an LED displaying the power status located on the front panel of EKI-2701PSI.
Table 2.1: EKI-2701PSI LED Definition
LED
Color
Power
Green
EKI-2701PSI User Manual_ed1
Description
On
Power input is active
Off
Power input is inactive
8
2.2 Dimensions (units: mm)
Figure 2.1: Front View of EKI-2701PSI series
9
Chapter2
Figure 2.2: Side View of EKI-2701PSI series
EKI-2701PSI User Manual_ed1
10
Figure 2.3: Rear View of EKI-2701PSI series
11
Chapter2
The terminal block for power output is located on the top side. Please refer to page 16 for pin
assignment.
Figure 2.4: Top View of EKI-2701PSI series
EKI-2701PSI User Manual_ed1
12
2.3 Mounting
The EKI-2701PSI support two mounting methods: DIN-rail & Wall.
2.3.1
Wall mounting
EKI-2701PSI can be wall-mounted by using the included mounting kit. Then, hang on
the EKI-2701PSI to the nails on the wall.
First, use the screws included in the package to combine the EKI-2701PSI and metal
mounting kit. And then you can install the device firmly via the components, please see
Figure 2.5 as below.
Figure 2.5: Combine the Metal Mounting Kit (units: mm)
13
Chapter2
2.3.2
DIN-rail Mounting
You can also mount EKI-2701PSI on a standard DIN-rail by following the steps below.
The DIN-rail kit is screwed on the industrial switch when out of factory. If the DIN-rail kit
is not screwed on the industrial switch, please screw the DIN-rail kit on the switch first.
First, hang the EKI-2701PSI to the DIN-rail with angle of inclination. See figure 2.6.
Figure 2.6: Installation to DIN-rail Step 1
EKI-2701PSI User Manual_ed1
14
Then, let the device down straight to slide over the rail smoothly. See Figure 2.7
Figure 2.7: Installation to DIN-rail Step 2
15
Chapter2
2.4 Network Connection
Use the four twisted-pair, Category 5e cabling for RJ-45 port connection. The cable between
the splitter and the non-PoE device must be less than 100 meters (328 ft.).
EKI-2701PSI User Manual_ed1
16
2.5 Power Connection
The EKI-2701PSI supports dual +24VDC power outputs.
Figure 2.13: Pin Assignment of the Power Connector
Insert the positive and negative wires into the V+ and V- contacts on the terminal block
connector. Users can wire the ground contact to the ground of the device whose power input
connects to this splitter.
17
Chapter2
EKI-2701PSI User Manual_ed1
18
CHAPTER
Troubleshooting
19
Chapter2
Chapter 3
Troubleshooting
1.
Power Input
Verify that the splitter is using the right power source (+44 ~ 57VDC).
2.
Cable
Select the proper UTP cable to construct your network. Please check that you are
using the right cable.
3.
Diagnosing LED Indicator
If the power indicator does not light up when the PoE In port is connected to a power
source equipment (PSE) via the UTP cable, check for loose cable connections, power
losses or surges at power outlet. If you still cannot resolve the problem, contact the
local dealer for assistance.
EKI-2701PSI User Manual_ed1
20
APPENDIX
Pin Assignment & Wiring
21
Chapter2
Appendix A
Pin Assignment & Wiring
It is suggested to adopt ELA/TIA as the wiring of the RJ-45.
Figure A.1: RJ-45 Pin Assignment
RJ-45 ports: 10/100/1000Mbps ports are auto-sensing for 10Base-T, 100Base-TX, or
1000Base-T connections.
Data pins for PoE IN port: 1, 2, 3, 6, 4, 5, 7, and 8
Power pins for PoE IN port: 4, 5 (V+); 7, 8 (V-)
or 1, 2 (V+); 3, 6 (V-)
Data pins for DATA OUT port: 1, 2, 3, 6, 4, 5, 7, and 8
Power output (located on the top side): 1 x 6 pin terminal block
Figure A.2: EIA/TIA-568B
EKI-2701PSI User Manual_ed1
22
Figure A.2: EIA/TIA-568A
23
Chapter2
Download PDF