Dyna LAL User Manual

User Manual – DynaLAL
Dynamic Low Air Loss (DynaLAL)
Alternating + Pressure Relief
User Manual
Distributed by: Quart Healthcare Inc.
www.quarthealthcare.com
User Manual – DynaLAL
Warning






Connect the Master Control unit to an appropriate power source
Do not use the system in the presence of any flammable gases (such as anesthetic agents)
Keep the pump and mattress away from sources of liquid and open flames
Keep mattress away from sharp objects
The device is not AP/APG protected
Keep mattress system away from heating devices
Caution
 Consult clinical instructor before use of mattress
 Support surfaces should always be used in conjunction with a care plan that includes the turning/repositioning
of the patient over a 24-hour period
 The control unit should only be repaired by an authorized distributor
 Do not drop the control unit or store it in direct sunlight or extreme cold conditions
1. Product Description
The DynaLAL system is a unique and innovative specialized mattress replacement unit. The system utilizes
low air loss technology with a high flow rate that provides pressure management for the treatment of pressure
ulcers. The advanced 3:1 alternating function also provides active prevention for pressure relief, especially for
those in acute care and long term care settings (the cells inflate and deflate in a 3:1 cycle, meaning 2/3rds of
the body is always supported at any one time). The DynaLAL system offers “deep-cell therapy”; whereby, the
cells completely collapse providing “0” pressure at the point of deflation. The soft-firm adjustment allows the
patient to adjust the firmness or softness of the surface for optimal comfort through 8 digital scales. The
surface also has 2 inches of enclosed convoluted foam to provide extra protection and comfort for the patient
in the event of a power failure and the mattress deflates.
User Manual – DynaLAL
3-1 Alternation Cycle Illustration
Control Unit Features (pump)



Alternating time can be adjusted in 5min increments to 95 min. In addition, the caregiver can select the
“Static Function” stopping the alternating function and providing only low air loss therapy
The auto firm function provides uniform firmness for nursing procedures
Power failures produce an audio alarm for added safety. The alarm can be disabled by pushing the
ALARM RESET Button on the front panel


Double insulation provides near silent operation
Foot board mounting rack provides convenient placement on bed.
User Manual – DynaLAL
Master Control Unit
Part No
Device Identifier (Health
Canada)
Size (cm)
Weight (Kg)
Phase Time
Rated Voltage
Fuse Rating
Max Current
Rated Frequency
Protection Type
Classification to Health Canada
Operation Temperature
Mode of Operation
Safety Standard
FC-QHI0079
FC-CRP0079
42(L)x17 (W)x27(H)
6.1
5 ~ 95
120 volt
T5AH 250V
18W
60 Hz
Classification (UL60601-1) Class I, Type BF
Class II
15 c ~ 40 c
Continuous
UL/CSA
Mattress Replacement Features



Individual air cushion design for maximum pressure distribution.
Air cells are vented to provide true low air loss therapy with a high flow rate.
Individual air cushion design for maximum pressure distribution.
Alternating Mattress Replacement Features
Part No
FM-QHI0001
Device Identifier
FM-CRP0001
(Health Canada)
Size (cm)
89(W)x203(L)x24(H) – (36” x 80” x 9.5”)
Weight (Kg)
17.5 Kg
Part No
Device Identifier
(Health Canada)
Size (cm)
Weight (Kg)
FM-QHI0005
FM-CRP0005
Cells Material
Cover Type
Cover Material
Base Material
PU
Zipper cover with removable foam base
Nylon knitted fabric w/ PU coating finish
Woven Polyester fabric w/ PVC backing
122(W)x203(L)x24(H) – (48” x 80” x 9.5”)
21.0 Kg
User Manual – DynaLAL
2. Instructions for Proper Use
i.
ii.
iii.
iv.
v.
vi.
vii.
viii.
ix.
x.
xi.
xii.
xiii.
xiv.
Remove the existing mattress from the bed frame
Replace the standard mattress with mattress replacement system (orient mattress so that the air tube is at the
foot of the bed)
Secure straps beneath the mattress to the bed frame
Hang the control unit on the foot board of the bed frame
Attach the air tube connectors to the socket on the left panel of the control unit (connectors and sockets are
colour coded)
Verify that air hoses are not kinked under the mattress
Attach cover to mattress
Plug in the control unit and turn on the master power switch on the right side panel (the STANDBY LED will
illuminate)
Push the STANDBY/OPERATE button on the front panel (OPERATE LED will now be illuminated and the
control unit will be in operation)
Push the AUTO FIRM button for fast inflation. Allow 4-7 min for full inflation.
After the mattress is fully inflated, the caregiver can transfer the patient to the mattress (note: the mattress can
be inflated while a patient is laying on it)
Push AUTO FIRM again to release the fast inflation mode
Alternation time can be adjusted by the CYCLE TIME button.
When the control unit is powered-on, it will default to previous setting.
Static Function: Push the STATIC button and adjust the comfort control by pressing the SOFT/FIRM button to
achieve maximum patient comfort. On this mode the system provides low air loss therapy. Perform a hand
check by placing hand under the patient’s buttocks between the cells and foam. The patient should have at
least 4 cm of clearance between the buttocks and the bottom of the mattress. If the STATIC function is
selected the time display will remain blank.
Dynamic Function: Push the alternate button to enable the 3:1 alternating function.
Lock-out Function: When lock-out function activates, buttons on control panel will be non-functional.
CPR Deflation: For quick mattress deflation disconnect the hose connector from the controller and release the
CPR quick deflation valve.
User Manual – DynaLAL
3. Cleaning
The mattress should be cleaned on the bed weekly using a damp soft cloth and mild detergent. If the top or
bottom cover becomes severely soiled, remove, clean as follows, and replace with a clean cover. Covers can
be washed and thermally disinfected in a washing machine. Cover should not be put into a dryer. (Never use
phenol-based cleaning solutions)
Industrial cleaning
Break wash
Main wash
Main wash
Extraction
3 cold rinses
Extraction
Domestic cleaning
Pre-wash
Main wash
Extraction
Cold rinses
cold
60C
70C
10 min
6 min
10 min
2 min
5 min
cold
70C
10 min
2 min
TUMBLE DRYING OR TUNNEL DRYING IS NOT RECOMMENDED
Mattress cells can be wiped with a solution of sodium hypochlorite 1000ppm or any other non-phenolic
germicidal solution.
Note: The control unit should also be cleaned weekly using a damp soft cloth and mild detergent (Switch off
the electrical supply to the pump and disconnect the power cord from the main supply before cleaning
and inspection).
The Pump: The casing of the pump is manufactured from ABS plastic. If soiled it can be wiped down with a
sodium hypochlorite solution to dilution of 1000ppm or any EPA-approved, hospital-grade disinfectant.
(Do not use phenol based cleaning solutions)
User Manual – DynaLAL
Cleaning procedure for air filter
1. Air Filter is located at the back of the control unit, inside the carry handle. No tools are required to remove
it. Air Filter must be removed for inspection at least once a month and washed under running tap water if
necessary. Squeeze to remove excess water before reinstalling it.
2. Use a soft brush to remove dust and debris from the air-intake muffler prior to reinstalling the filter.
3. New filters are also available.
(Do not use phenol based cleaning solutions)
(Switch off the electrical supply to the pump and disconnect the power cord from the main supply before cleaning
and inspection)
4. Storage and Care
Control Unit:
 Check the power cord and plug for abrasions and excessive wear
 Plug in the unit and verify air flow from the hose connection ports
 Place in plastic bag for storage
Mattress Replacement System
 Check the air manifold for kinks or breaks. Replace if necessary.
 Twist open the CPR plug at the head of the mattress and disconnect the air feed tubes. All of the air
will be expelled. Starting at the head of the mattress roll towards the foot of the bed. Use the base
mounted straps to secure.
It is recommended that the following guidelines are used whenever the system is being stored or transported
to another location:
Temperature limitations
5C to 60C
Relative humidity
30% to 75%
2. Maintenance and Troubleshooting
No daily maintenance is required. This equipment should only be serviced by authorized technical personnel.
In case of minor problems refer to the following:
Inspection Procedure
Possible Solution
1. Is the power source correct? Improper voltage may
cause the pump to function abnormally and damage
the control unit.
2. Do the air tubes allow smooth airflow? Is an air tube
kinked?
3. Is there any air leakage from the air cells?
4. Is there any air leakage from air tube between
mattress and control unit?
5. Has the air tube connector been connected properly?
1. Use power regulator.
Symptom
The air is flowing out from the control unit but
the mattress is not inflating
2. Adjust the air tubes to enable smooth
air flow.
3. Replace with new air cells
4. Replace with new air tubes
User Manual – DynaLAL
The Control Unit is not working
1. Check the power cord and the power voltage.
2. Check the fuse
Some air cells have abnormal low air pressure
while the air pressure for other air cells is
normal
1. Is the connection between air cells and the manifold
kinked?
2. Is there any air leakage from the air cells?
5. Re-connect the air tubes.
1. Use a power regulator
2. Replace with a new fuse
1..Adjust the connection between cells
and manifold
2. Replace with a new air cell.
3. Warranty

Quart Healthcare Inc. guarantees that this equipment is free from defects in materials and
workmanship. Our obligation under this warranty is limited to the repair of equipment returned to the
place of purchase within 24 months of delivery date

We agree to service/adjust any equipment returned, and to replace or repair any part that is proven to
be a warranty defect, at no charge

This warranty excludes equipment damage through shipping, tampering, improper maintenance,
carelessness, accident, negligence or misuse, or products that have been altered, repaired or
dismantled other than with the manufacture’s written authorization and by its approved procedures and
by properly qualified technicians

In no event shall Quart Healthcare Inc. be liable for any direct, indirect or consequential damages or
losses resulting from the use of equipment
Download PDF