Hameg HMC8041-HMC8042-HMC8043- Power Supplies

Hameg HMC8041-HMC8042-HMC8043- Power Supplies
Product Brochure | 01.00
Test & Measurement
R&S®HMC804x
Power Supply
100 W and 1, 2 or 3 Channels
Total output power
Output current per channel
All models: 100 W
HMC8041: max. 10 A
HMC8042: max. 5 A
HMC8043: max. 3 A
EasyArb
Create individual V/I curves
directly on the device
FuseLink
Combine electronic fuses
as required
EasyRamp
Simulate a startup curve,
programmable directly on the
device
Sequencing
Sequenced start of channels
At a glance
One, two or three channels – R&S®HMC804x power supplies with their
specifications and wide range of functions are ideal for use in development
labs and industrial environments. Thanks to their high energy efficiency, the
linear power supplies remain cool and quiet, even at maximum load. Practical
interfaces and connectors allow users to work quickly and conveniently with
the R&S®HMC804x, even in 19“ racks.
Trigger input
Start and control
EasyArb, et al.
Analog input
Control output channel
with external voltage and
current
High energy efficiency
Low heat dissipation and
quiet fan
Brilliant Screen
Data logging
Protection
UI-Tracking
QVGA TFT Display
with 320 x 240 Pixels
To USB flash drive in CSV format
Overvoltage (OVP) and Overpower
protection (OPP) for all outputs
Convenient parallel and
serial operation
2 R&S®HMC804x
The R&S®HMC804x family consists of three models with a maximum total power
of up to 100 W and a continuous voltage range from 0 V to 32 V. The one-channel
R&S®HMC8041 delivers a maximum of 10 A, the two-channel R&S®HMC8042 a
maximum of 5 A and the three-channel R&S®HMC8043 a maximum of 3 A per
channel. The two-channel and three-channel models enable users to connect
multiple outputs in parallel or in series to increase the voltage or current. The
outputs are galvanically isolated, floating, and protected against overloading and
short circuits. Voltage, current and power values are output on a brilliant QVGA
display.
The R&S®HMC804x offers a wide range of logging functions, an integrated
energy meter and electronic fuses that can be individually combined for
each channel, making it ideal for hardware developers, labs and industrial
environments. Linear switching power supplies ensure high efficiency, for
minimum heat dissipation even at full load. Developers and industrial users
benefit from useful functions such as sequenced start of channels, EasyArb
and EasyRamp functions that are directly programmable on the device, an
analog input for external control of voltage values, an external trigger input
for controlling channels and arb steps, and adjustable overvoltage/overpower
protection for each channel.
All connectors, including SENSE, are available on the rear panel. A cage clamp
facilitates rack installation and deinstallation. The LXI-compliant power supply
can be controlled via LAN, USB or an optional GPIB interface. The CDC (virtual
COM port) and TMC classes are supported for communications via USB. The
remote control commands are based on the SCPI standard.
The R&S®HMC804x power supplies from the Rohde & Schwarz value instruments
product range offer top quality and intelligent, practical functions at an extremely
attractive price.
R&S®HMC804x 3
Key facts
Clear display of all measured parameters
❙❙ Brilliant QVGA color display (320 x 240 pixel)
❙❙ Realtime voltage, current and power values
❙❙ High setting and readback resolution: 1 mV and 0.1 mA/1.0 mA
(depending on current and model)
❙❙ Low residual ripple due to linear postregulation
❙❙ High energy efficiency, low heat dissipation and quiet fan
Ideal for industrial environments
Remote control
❙❙ USB interface (CDC/virtual COM port, TMC)
❙❙ LAN interface, LXI-compliant
❙❙ Optional GPIB interface
❙❙ Remote control via SCPI-based commands
Galvanically isolated, floating and short-circuit-proof outputs
❙❙ Front panel: 4 mm (0.16 in) safety sockets
(R&S®HMC8041 including SENSE)
❙❙ Rear panel: WAGO cage clamp for all channels including SENSE
❙❙ Convenient parallel and serial operation via
❙❙ V/I tracking
Protective functions adjustable for each channel
❙❙ Overvoltage protection (OVP) for all outputs
❙❙ Overpower protection (OPP) for all outputs
❙❙ FuseLink (freely combinable electronic fuses)
❙❙ FuseDelay (fuse activation delay)
Ideal power supply for hardware developers and labs
❙❙ EasyArb function for user-definable V/I curves
❙❙ EasyRamp for simulating a start-up curve
(directly programmable on device)
❙❙ Sequencing (sequenced start of channels)
❙❙ Energy meter (measurement of energy output)
❙❙ Analog input for external control via voltage (0 V to 10 V)
and current (4 mA to 20 mA)
❙❙ Trigger input for starting/controlling EasyArb
❙❙ Data logging to USB flash drive in CSV format
4 R&S®HMC804x
Application
How the HAMEG R&S®HMC804x meets your needs
Engineering lab
❙❙ FuseLink (freely combinable electronic fuses)
❙❙ EasyArb function for user-definable V/I curves
❙❙ EasyRamp for simulating a start-up curve (directly programmable on device)
❙❙ Built-in energy meter
❙❙ Data logging to USB flash drive in CSV format
❙❙ Analog input for external control via voltage (0 V to 10 V)
and current (4 mA to 20 mA)
❙❙ Trigger input for starting/controlling EasyArb
❙❙ Sequencing (sequenced start of channels)
❙❙ Rear connectors for all channels, including SENSE
❙❙ WAGO cage clamp on the rear panel for easy installation and deinstallation
❙❙ Remote control via SCPI-based commands
❙❙ LAN interface, integrated web server, LXI-compliant
❙❙ Optional GPIB interface (R&S®HMC804xG models)
Automatic test
equipment (ATE)
Production
environment
Power supply units in industrial production environments are often found in
19” racks. The HMC804x series instruments are very suitable for this use as all
models can be integrated into 19” racks with the rack mounting kits HZC95.
Two HMC8043 models built side by side result in 6 channels on 2 rack units.
Please ensure sufficient space is available in the rack for adequate cooling
(required minimum space above a HMC804x: 1 rack unit).
Additionally, all front panel connectors plus SENSE lines are located at the
back panel of the instrument. In order to facilitate the regular fitting-out for
calibration the rear panel connector was designed with a WAGO cage clamp.
The complementary part is available as option HZC40.
Base unit
Channels
Power
GPIBInterface
R&S®HMC8043G
3
99 W (33 W/Channel, 3 A (max.))
✔
R&S®HMC8043
3
99 W (33 W/Channel, 3 A (max.))
✗
R&S®HMC8042G
2
100 W (50 W/Channel, 5 A (max.))
✔
R&S®HMC8042
2
100 W (50 W/Channel, 5 A (max.))
✗
R&S®HMC8041G
1
100 W (10 A (max.))
✔
R&S®HMC8041
1
100 W (10 A (max.))
✗
R&S®HMC804x 5
¸HMC8043, ¸HMC8042, ¸HMC8041
Power Supply
Analog Interface
Resolution
voltage
Miscellaneous
1mV
Shunt resistance 4…20mA
250 Ohm
Input power option
100-240 VAC +/-10% 50/60 Hz
>10 kOhm
Maximum input power
200W
The specifications are based on a 30 min warm-up period.
current
0.1mA (I<1A)
1mA (I>=1A)
Input resistance 0…10V
Update rate V/I interface
10 changes/sec
Fuse
T3, 15L 250V
Electrical Specifications
Voltage to earth
250VDC
Response time V/I interface
<150ms
Operating temperature
+0°C ..+40°C
Reverse Voltage
33V max.
Trigger level
TTL
Storage temperature
-20°C..+70°C
Inverse Voltage
0.4V max.
Trigger response time
<1ms
Humidity
5...80%
Resolution
14 bit
3A
33W
50W
100W
Max. current allowed in case of
inverse voltage
Voltage Output
0-32V
Supplemental characteristics
Current Output
¸HMC8043
¸HMC8042
¸HMC8041
3A max (power limit)
5A max
10A max
Number of outputs
¸HMC8043
¸HMC8042
¸HMC8041
3
2
1
Front connectors
Line & load regulation (Sense connected)
Constant voltage
¸HMC8043
¸HMC8042
¸HMC8041
Constant Current
¸HMC8043
¸HMC8042
¸HMC8041
<0.02% + 3mV
<0.03% + 5mV
<0.03% + 5mV
Rear connectors
Temperature coefficient for
12 months (per K)
±(% of output + offset)
3,5” / QVGA
Dimensions (H x W x D)
222 x 88 x 280 mm
Parameter
Voltage, current, time and interpolation
mode
Rack mount capability 1/2 19“
Yes
Weight
2,6kg
Number of Points
512
Dwell time
10ms … 10min
Repetition rate
continous or burst mode with 1…255
repetitions
Trigger
manually, interface or trigger input
4 mm saftey sockets
Wago male connector (713-1428/037-000),
8x2-pole, pin spacing 3.5 mm / 0.138 in
voltage: >0,02% +3mV
current: >0,02%+3mA
Output voltage overshoot during
turn-off of AC power and
channel output on
100mV
Over temperature protection
Display
Arbitrary (EasyARB)
Yes
Sampling speed
1000,100,10,1…3600 Sa/s
Resolution ¸HMC8043
1mV / 0.1mA (<100Sa/s);
10mV / 1mA (1000Sa/s)
Resolution ¸HMC8042/41
1mV / 1mA (<100Sa/s);
10mV / 10mA (1000Sa/s)
Memory
Internal memory and External memory
(USB-Stick)
Maximum number of Points
limited by memory
<0.03% 200µA
<0.03% 200µA
<0.03% 200µA
Voltage programming speed (within 1 % of total excursion)
Voltage ripple 20Hz to 20MHz
(Front connector)
450µVrms / 4mVpp
no load
10ms + µC-time
with resistive load
10ms + µC-time
Current ripple 20Hz to 20Mhz
typ. <1mArms
Response time
(10%...90% load change)
no load
500ms + µC-time
Synchronicity
<100us
1ms (±20mV)
with resistive load
10ms + µC-time
Delay per channel
1ms … 60s
Remote Sense max. voltage
1V
Remote interfaces
USB-TMC, USB-CDC (Virtual COM), LAN
(LXI), GPIB (optional)
Positive voltage change
Negative voltage change
Sequencing
Command processing time
<30ms
Programming accuracy (23° C ±5° C)
Over Voltage Protection
Yes
voltage: all models
<0.05% +2mV
Over Power Protection
Yes
0.05% +2mA
0.1% +5mA
Energiemeter
Yes
EasyRamp
Yes
EasyRamp time
10ms ... 10s
current: ¸HMC8043
¸HMC8042/41
Readback accuracy (23° C ± 5° C)
voltage: all models
<0.05%+2mV
current: ¸HMC8043
¸HMC8042
¸HMC8041
0.05% +2mA
0.05% +7mA
0.05% +4mA
6 R&S®HMC804x
HZC95
19“ rackmount kit
for HMC series, 2 HE
HZC40
Female connector
with ejectors, 8x2-pole
Logging
Accessories included:
Line cord, printed operating m
­ anual, software-CD
Printed operating manual
HZ72
IEEE-488 (GPIB) bus
interface cable
HZ10
5x silicon test lead
HZ10S: black, HZ10R: red, HZ10B: blue
Software-CD
Power Supply
¸HMC804x
Benutzerhandbuch
User Manual
Deutsch / Englisch
100W
Maximum power per Channel
¸HMC8043
¸HMC8042
¸HMC8041
Benutzerhandbuch / User Manual
Total power output
Recommended Accessories
Electronic Fuse
Fuse trip time
<100us
Fuse linking
<100us + trip time of linked channel
Fuse delay
10ms ... 10s
R&S®HMC804x 7
value-instruments.com
HAMEG Instruments GmbH
Industriestr. 6 | 63533 Mainhausen | Germany | Phone +49 (0) 6182 8000
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG
HAMEG Instruments® is a registered trademark of HAMEG Instruments GmbH
Trade names are trademarks of the owners
PD 3607.0169.32 | Version 01.00 | 05 / 2014 | © HAMEG Instruments GmbH
Data without tolerance limits is not binding | Subject to change
3607016932
PD 3607.0169.32 V 01.00 PDP1 en
www.hameg.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement