23914-01a - Tanning Bed Parts

Official SPEED™ 205 Re-certification Notice
23914-01 A
October 12, 2000
Re:
Re-certification of the SUNSTAR® (ZX30 and ZX32) SPEED™ system sunbeds
Dear Salon Owner;
Thank you for purchasing the SPEED™ lamp upgrade kit. This letter will serve as the official recertification notice from the manufacturer of your sunbed. Please retain this letter, keeping it with your
sunbed's original user manual. State or local inspectors may ask to see it.
All SunStar ZX30 and SunStar ZX32 series SPEED™ system sunbeds have been re-certified to allow the
use of the SPEED™ 205 Wolff® Model SPD71-T12-205 Bi-Pin lamp in the sunbed's canopy. Included
with this letter you will find a new white Quick Clip profile that has the new certification wording silkscreened onto it. Please remove the existing profile from your sunbed, following the instructions attached,
and replace it with the new one provided.
The sunbeds included in the re-certification were originally labeled:
SUNSTAR® ZX30 SPEED™ system
SUNSTAR® ZX30 SPEED™ 175 system
SUNSTAR® ZX30-3F SPEED™ system
SUNSTAR® ZX30-3F SPEED™ 175 system
SUNSTAR® ZX32 SPEED™ system
SUNSTAR® ZX32 SPEED™ 175 system
SUNSTAR® ZX32T SPEED™ system
SUNSTAR® ZX32T SPEED™ 175 system
SUNSTAR® ZX32-3F SPEED™ system
SUNSTAR® ZX32-3F SPEED™ 175 system
Please note that the notation "SPEED™ 175 system" has been changed to " SPEED™ system" to allow
for the lamp upgrade. This notation change extends to the ballasts located in your sunbed. The ballasts
labeled "SPEED™ 175 system" are fully compatible with the new lamps.
The labeling provided on the updated profile has been reproduced on the back of this letter to satisfy the
requirements set out in 21 CFR 1040.20 (e) (i).
This upgrade is voluntary and may be performed if the sunbed owner desires. If you choose not to
upgrade your equipment rest assured that it is still fully FDA compliant as originally manufactured.
Office of Regulatory Affairs
Spectrum Products, Inc.
DANGER
Ultraviolet radiation. Follow instructions. Avoid
overexposure. As with natural sunlight, overexposure can cause eye and skin injury and allergic reactions. Repeated
exposure may cause premature aging of the skin and skin cancer.
WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS
OR LONG-TERM INJURY TO THE EYES.
Medications or cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician before using sunlamp if you are using
medications or have a history of skin problems or believe yourself
especially sensitive to sunlight. If you do not tan in the sun, you are
unlikely to tan from the use of this product.
To use, lie down under the canopy and pull down as far as adjustment
will allow. Minimum use distance from face tanner (If Equipped) is 1 inch
or 2.5 centimeters. Minimum use distance elsewhere is touching the
clear plastic panels. Do not use without clear plastic panels (or wire grid
for models using wire grid) in place.
Common to all units
Untanned persons should not tan on consecutive days during their first
week of tanning. Never tan more than once a day. Tanning normally
appears after the first few sessions and maximizes after approximately
four weeks. Tan once or twice per week thereafter to maintain appearance. Persons already having a base tan may begin at advanced levels
corresponding to the extent of their base tan.
RECOMMENDED EXPOSURE TIMES IN MINUTES
Skin Type:
I
MAXIMUM EXPOSURE TIME IS 20 MINUTES
Level 1/Week 1
1st-3rd sessions
Sensitive Skin (Burns easily and severely and does not tan.)
Level 2
Level 3
Level 4
NOT RECOMMENDED FOR TANNING
II Light
(Burns easily and severely and tans minimally.)
4
8
12
16
20
III Normal
(Burns moderately and tans average.)
6
10
15
20
20
IV Dark
(Burns minimally, tans easily and above average.)
8
12
16
20
20
WARNING: Read the instructions booklet before using this sunlamp
product. All persons in the room should wear protective eyewear when
lamps are on. Recommended eyewear: Provided eyeshields (Lucas
Products Super Sunnies or Intrexco No. 5635/1) or equivalent eyewear
as defined under 21 CFR 1040.20. Other types of eyewear may not provide adequate protection. Disconnect power cord before attempting to
clean, relamp, or engage in the maintenance of this product.
SunStar® ZX30 SPEED™system
SunStar® ZX32 SPEED™system
ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS
EQUIPMENT:
SPEED 175™ Wolff® Model SPD75-T12 Bi-Pin (Bench Only)
SPEED™ 205 Wolff® Model SPD71-T12-205 Bi-Pin (Canopy Only)
THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS
FOR SUN LAMP PRODUCTS UNDER 21 CFR PART 1040.20
SunStar® ZX32T SPEED™system
ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS
EQUIPMENT:
SPEED 175™ Wolff® Model SPD75-T12 Bi-Pin (Bench Only)
SPEED™ 205 Wolff® Model SPD71-T12-205 Bi-Pin (Canopy Only)
Turbo Sun™ S Wolff® Model F8-T5-10W (Turbo Face Lamps)
THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS
FOR SUN LAMP PRODUCTS UNDER 21 CFR PART 1040.20
SunStar® ZX30 3F SPEED™system
SunStar® ZX32 3F SPEED™system
Subsequent
Maximum
ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT:
SPEED™ 175 Wolff® Model SPD75-T12 PREHEAT-BIPIN (Bench lamps)
SPEED™ 205 Wolff® Model SPD71-T12-205 BIPIN (Canopy lamps)
Heraeus E400 HPT, Philips Model HPA 400/30s or CosmoTech Model 23045
(SolarMax™ IFT facial unit lamps)
THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS
FOR SUN LAMP PRODUCTS UNDER 21 CFR PART 1040.20
Replacing the Silk-screened Profile is a fairly simple
operation. You will need a flat, blunt tool (a putty
knife works great) and a Phillips screwdriver.
First, pry the front trim profile off of the sunbed
canopy (as shown at right). Next, remove the handle by unscrewing the three Phillips screws that
secure it to the canopy.
To remove the Silk-screened Profile, pull it back
from the bottom (like when you remove the acrylic)
so it swings open. Use the flat tool to pry the profile
away from the aluminum frame from the top as
shown in the lower picture at right. As the top is
pulled away the profile will fall off of the frame.
Now take the new Silk-screened Profile (that indicates SPEED™ 205 lamps) and look at it from the
end. You will notice it has a hook and an “S” shape
(see illustration below). Slip the hook into the slot in
the aluminum frame and press the “S” shape over
the ridge until it snaps tight.
Snap the profile back over the acrylic. Reattach the
handle. Press the trim profile back into place.
“S” SHAPE
HOOK
ALUMINUM FRAME
PROFILE
Download PDF