Wireless Ultrasonic Parking Sensor Systems for Commercial Vehicles

Wireless Ultrasonic Parking Sensor
Systems for Commercial Vehicles
INSTALLATION/USER'S MANUAL
BSSK1000: Under Mount Backup Sensor System
BSSK1001: Flush Mount Backup Sensor System
90-21 144th Place
Jamaica, NY 11435
1.800.227.2095
www.roscovision.com
BSSK1000 UNDER MOUNT BACKUP SENSOR SYSTEM COMPONENT LIST:
Components:
P/N
Qty.
LED Display w/Double Sided Tape
BSSKD200
1
Control Box
BSSKT300
1
Under Mount Sensors (Set of 4) w/Hardware Kit
BSSKS100
1
Hardware Kit Group 1: Foam Wedges
8
Hardware Kit Group 2: Screws and Washers
12
Hardware Kit Group 3: Tie Wraps
15
BSSK1001 FLUSH MOUNT BACKUP SENSOR SYSTEM COMPONENT LIST:
Components:
P/N
Qty.
LED Display w/Double Sided Tape
BSSKD200
1
Control Box
BSSKT300
1
Flush Mount Sensors (Set of 4) w/Hardware Kit
BSSKS101
1
Hardware Kit Group 1: Washers
8
Hardware Kit Group 2: Screws
4
Hardware Kit Group 3: Tie Wraps
15
BSSKT300
BSSKD200
BSSKS100
BSSKS101
WARNING
• Please read this manual carefully before using the product.
• This system is intended as an aid to safe reverse operation. Drivers must always use extreme ­
caution when operating a vehicle
• Sensors are to be used as parking aides for fixed objects such as vehicles and buildings.
They are not to be used for pedestrian detection.
1
www.roscovision.com
Wireless Backup Sensor Kit with
Ultrasonic Technology
Rosco ultrasonic wireless backup sensor systems
provide safety advantages that protect drivers, vehicles
and business profits. These systems are ideal for
school buses, work trucks, RVs and other commercial
vehicles.
The wireless backup sensor system is automatically
activated when the driver shifts into reverse gear.
Small flush or surface mount sensors are installed at
the rear of the vehicle. The sensors send and receive
ultrasonic waves that reflect off obstructions and alert
the driver to their presence. There is an audible alarm
that gradually increases in frequency as you approach
the obstacle, and an LCD screen displays the distance
to the obstruction. A continuous "beep" and red
distance indicator alerts the driver when the vehicle is
within one (1) foot of the obstruction.
CONTENTS
How To Read
Display............... 3
Sensor Detection
Range & Warning
Method............... 4
Sensor
Installation........ 5
Control Box
Installation........ 6
Wiring
Diagram............. 7
Display
Installation........ 7
Technical Specifications:
Operating range: Operating current:
Detection distance:
Ultrasonic frequency:
Working temperature:
Display size: Sensing resolution DC9 ~ 32V
20-150mA @ 12V
8.0 ~ 0.0 ft
40KHz
-22 ~ 158°F
3.7 x 1.9 x 0.8 inches
0.5 ft
Testing &
Maintenance..... 8
Installation Tools:
5.
1.
7.
2.
4.
6.
3.
8.
1. Wire Tester
4. Wire Stripper 7. Drill
2. Phillips Screwdriver 5. Pencil
8. Tape
3. Tape Measure
6. Hole Saw
A Century of Automotive Safety
2
How To Read Display
Distance (ft)
Green Lights
Safe Zone
(8.0 ft to 3.5 ft)
F
Yellow Lights
Caution Zone
(3.0 ft to 1.0 ft)
Red Lights
Danger Zone
(1.0 ft to 0.0 ft)
Both the Flush and Under Mount
­backup sensor systems are
­automatically activated when the driver
shifts into reverse gear.
There are three (3) volume options.
They are HIGH, LOW and OFF. The
adjustment switch is on the back cover
of the display unit.
UNIQUE ID
Each control box has a unique ID to
ensure secure data ­transmission from
control box to t­he ­­display. The display
has the c­ apability to pair with a new
control box. This allows the ­customer
to replace the display or control box if
necessary.
3
Cabin Temperature
How To Reprogram The Display:
1. Turn ignition on (DO NOT START).
2. Put the car in reverse.
3. Press the button on back of display one time for about 5 seconds. (See Below)
4. Display will store the unique ID of the nearest control box ­
automatically.
Press the button
www.roscovision.com
Sensor Detection Range & Warning Method
1. Safe Zone
Safe
Zone
8.0 ft to 3.5 ft
Distance Display:
8.0 to 3.5 ft.
OBSTRUCTION
Alarm Sound:
8.0 to 5.5 ft. - None
5.0 to 3.5 ft. - Slow "Beep"
LED Lights:
Green
2. Caution Zone
Caution
Zone
3.0 ft
to
1.0 ft
Distance Display:
3.0 to 1.0 ft.
OBSTRUCTION
3. Danger Zone
Distance Display:
1.0 to 0.0 ft.
LED Lights:
Red
A Century of Automotive Safety
LED Lights:
­Yellow
Danger
Zone
1.0 ft
to
0.0 ft
OBSTRUCTION
Alarm Sound:
Continuous "Beep"
Alarm Sound:
Fast "Beep"
4
Sensor Installation
IMPORTANT:
The sensor installation steps are applicable to BOTH the Flush Mount and
Under Mount Backup Sensor Systems.
The individual sensors are labeled A,
B, C, and D. The sensors should be
installed in the following order:
Sensor A:
Sensor B:
Sensor C:
Sensor D:
Outer Driver Side
Inner Driver Side
Inner Passenger Side
Outer Passenger Side
It is highly recommended to install
all four (4) sensors. The ­system
­however, will work with less than four
if the v­ ehicle configuration cannot
­accommodate all the sensors.
A
6” - 9”
B
C
D
1’ - 1.5’
Figure. 1
1. For all setups, installer MUST make certain that sensors are
centered both horizontally and ­
vertically.
2. Installation height for sensors should be between 1 to 4 ft.
above ground.
A &DD should be located B 3. Sensors
C
6 to 9 inches from outer edge of vehicle.
4. When installing sensors, make
1-1.5ft
certain that no part of vehicle (hitch, 1-4ft
Figure. 2
etc.) is within 90° of the sensing range.
5. When installing sensors be certain the sensor is level, not at a angle. Place provided washers and
wedges if necessary.
6. Surface to install sensors must be vertical and flat.
Figure. 3
5
www.roscovision.com
Control Box Installation
Control box
IMPORTANT:
The marked sensor cables
(A,B,C,D) must be connected to the
­corresponding marked inputs on the
control box. See page 7.
Co
Figure. 1
1. Control Box MUST be installed in the cargo area or other protected area.
2.
After choosing a suitable control box position in the vehicle, drill the required holes to route the sensor cables to vehicle interior.
3. Pull sensor cables through drilled hole to vehicle interior.
4. Connect sensors cables to the
control box.
Figure. 2
5. Connect power and ground wires to the reverse light circuit.
Figure. 3
A Century of Automotive Safety
6
Wiring Diagram
Red 12V Wire
To Positive 12V Wire on the Reverse Light Circuit
To Termination/Chassis Ground
Black Ground Wire
A.
A.
B.
B.
Control box
C.
C.
D.
D.
Sensors
IMPORTANT: The marked sensor cables (A,B,C,D) must be connected to the
matching marked inputs on the control box.
Display Installation
1.
Select an area easily visible to the driver and mount display firmly. Clean surface with alcohol and use the included double sided tape to mount. (Figure 1)
2. Connect RED wire from display unit to ignition/switch power source.
3. Connect BLACK wire to vehicle ground.
4. Locate optional temperature sensor as desired.
Figure. 1
5. Power up and test.
7
www.roscovision.com
Testing
How to Test:
1. Apply the parking brakes.
2. Turn Ignition on (DO NOT START).
5.0ft
3. Place the shift gear to reverse ­position.
4. From behind the vehicle proceed to check the system by placing an item back and forth in front of each sensor.
Maintenance:
Always keep sensor clear from dirt, snow, and mud. Clean sensors with a soft
towel and low pressure water.
Trouble Shooting:
Problem
Cause
Solution
No power to display.
Bad power connections.
Check power
connections.
Display on, but no
reading while reversing.
Display not synchronized
with control box.
Press button on back of
display for five (5)
seconds to sync with
control box.
Orientation of sensors
do not match.
Sensor cables installed
to wrong control box
ports.
Check and change the
sensor cables to correct
ports on control box.
System always detects
the same distance.
Sensor may be detecting
ground or debris
(mud, snow, etc).
Check and adjust the
vertical angle on the
sensor. Clean sensor of
any debris.
A Century of Automotive Safety
8
90-21 144th Place
Jamaica, NY 11435
www.roscovision.com
Ph. 1.800.227.2095
A Century of
Automotive Safety
Fx. 1.718.297.0323
Printed in China
Lit. P/N: 05112011
Download PDF