Contents
EQUINOX
SLENDER BEAM BAR WHITE
User Manual
EQLED021
1.
Safety Instructions
2.
Features & Specifications
3.
How To Set The Unit
4.
Troubleshooting
5.
Fixture Cleaning
1. Safety Instruction
Warning
Ÿ To prevent or reduce the risk of electrical shock or fire, do not expose the
WARNING
Please read the instructions carefully as they include important
unit to rain or moisture.
information about installation, usage and maintenance.
Do not open the unit within five minutes after switching off.
Please keep
this User Guide for future consultation. If you sell the unit to another user
Ÿ The housing and lenses must be replaced if they are visibly damaged.
Installation
The unit should be mounted via its screw holes onto the bracket. Always
be sure that they also receive this.
ensure that the unit is firmly fixed to avoid vibration and slipping while
Unpack and check carefully that there is no transportation damage before
operating. Make sure that the structure to which you are attaching the
using the unit.
unit to is secure and is able to support a weight of 10 times of the unit’s
Ÿ Before operating, ensure that the voltage and frequency of the power
weight. Always use a safety cable that can hold 12 times of the weight of
supply match the power requirements of the unit.
Ÿ It’s important to ground the yellow/green conductor to earth in order to
avoid electric shock.
Ÿ The unit is for indoor use only. Use only in a dry location.
Ÿ The unit must be installed in a location with adequate ventilation, at least
50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
the unit when installing the fixture.
The equipment must be installed by professionals and it must be installed
in a place where is out of the reach of people and no one can pass by or
under it.
2. Features & Technical Specifications
Control: Sound active, auto, Master/slave and DMX 512 and CA-8 modes
Ÿ Disconnect the mains power before replacement or servicing.
DMX Channels: 1CH/6CH/12CH/14CH/27CH
Ÿ Make sure there are no flammable materials close to the unit while
Electronic dimming: 0-100%
operating as they may cause a fire hazard.
Ÿ Always use a safety cable when installing this unit. Do not carry the unit
with its head only, always carry it using the base.
Ÿ The maximum ambient temperature is: 40 . Don’t operate it where the
temperature is higher than this.
Ÿ In the event of a serious operating problem stop using the unit
immediately. Never try to repair the unit by yourself. Repairs carried out
by unskilled people can lead to damage or malfunction. Please contact
the nearest authorized technical assistance center. Always use the same
type spare parts.
Ÿ Do not touch any power cables during operation as the high voltage may
cause an electric shock.
Compact size with a high output
Voltage:
100V~240V, 50/60Hz
Fuse:
T 6.3A
Power consumption:
85W
Light source:
4 x 10W white LED
Dimension:
808 x 89 x253mm
Weight:
7.5 kg
Pan/Tilt:
540°/270°
Power sockets:
IEC IN/OUT
XLR sockets:
3-pin XLR IN/OUT
3. How To Set The Unit
The main functions are as below:
3.1 Control panel
ADDR
CHMD
001-512
1CH/6CH/12CH/14C
H/27CH
MAST
SLMD
SL1
SL2
SH1
Display
SHMD
Shows the various menus and selected functions
Button
SH3
SH4
MENU
Selects the programming functions
DOWN
To go backward in the selected functions
UP
ENTER
To go forward in the selected functions
Confirms the selected functions
Mains input
Connection to the power supply.
DMX input/output
For DMX 512 linking. Use 3-pin DMX cables to link to the controller or to
other units.
3.2 Main Functions
To select any of the given functions, press the MENU button up to where
the required function is showing on the display. Select the function by
pressing the ENTER button and the display will blink. Use the DOWN and
UP buttons to change the mode. Once the required mode has been
selected, press the ENTER button to confirm. To go back to the functions
without any changes, press the MENU button again. Press and hold the
MENU button for one second or wait for one minute to go back to the main
menu.
SH2
SOUN
Menu
SENS
LED
ON
OFF
000-100
ON
OFF
DISP INVERT
PAN INVERT
TILT INVERT
YES
NO
YES
NO
TEST
SELF-TEST
FHRS
Fixture hours
0 ~ 9999
VER
Software Version
RSET
RSET
(show 1) or
(show 2) or
(show 3) or
(show 4) mode.
Once the mode has been selected, press the ENTER button to confirm. To
DMX Address Setting
is showing on the display. Press the
go back to the functions without any changes press the MENU button
ENTER button and the display will blink. Use the DOWN and UP buttons to
again. Press and hold the MENU button for one second or wait for one
change the DMX-512 address. Once the address has been selected, press
minute to go back to the main menu.
Press the MENU button until
the ENTER button to confirm. To go back to the functions without any
changes press the MENU button again. Press and hold the MENU button
Sound Mode
one second or wait for one minute to go back to the main menu.
Press the MENU button to select
display will blink. Use the DOWN and UP buttons to select the
Channel Mode
(sound on) or
Press the MENU button to select
. Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
Channel) or
. Press the ENTER button and the
(6 Channel) or
(12 Channel) or
(sound off) mode. Once the mode has been selected,
press the ENTER button to confirm. To go back to the functions without
(1
any changes press the MENU button again. Press and hold the MENU
(14
button for one second or wait for one minute to go back to the main menu.
Channel) or
(27Channel) mode. Once the mode has been selected,
press the ENTER button to confirm. To go back to the functions without
any changes press the MENU button again. Press and hold the MENU
Sound Sensitivity
Press the MENU and use the UP and DOWN buttons to select
button for one second or wait for one minute to go back to the main menu.
select the sound sensitivity between value 0 and 100. Press the ENTER
and
button for confirmation after value selection. To go back to the functions
Master Mode or
Press the MENU button to select
Slave Mode
without any changes press the MENU button again.
. Press the ENTER button and the
Led Display
display will blink. Use the DOWN and UP buttons to select the
(Slave 1),
(Slave 2) or
(Master) mode. Once the mode has
been selected, press the ENTER button to confirm. To go back to the
Press the MENU button to select
. Press the ENTER button and the
functions without any changes press the MENU button again. Press and
hold the MENU button for one second or wait for one minute to go back to
display on) or
(Led display off) mode. Once the mode has been
selected, press the ENTER button to confirm. To go back to the functions
the main menu.
without any changes press the MENU button again. Press and hold the
display will blink. Use the DOWN and UP buttons to select the
(Led
MENU button for one second or wait for one minute to go back to the main
menu.
Show Mode
Press the MENU button to select
. Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
unit will run a self-test with its built-in programs. To go back to the functions
Display Inversion
Press the MENU button to select
the mode
without any changes press the MENU button again. Press and hold the
. Press the ENTER button to change
(display normal), it will be automatically saved after 8
seconds. Press the ENTER button again to select the mode
MENU button for one second or wait for one minute to go back to the main
menu.
(display
inversion). To go back to the functions press the MENU button. Press and
hold the MENU button for one second or wait for one minute to go back to
Fixture Hours
Press the MENU button up to when the
the main menu.
Press the ENTER button and the display will show the number of working
Display normal mode is for floor standing the unit.
is showing on the display.
hours of the unit. To go back to the functions press the MENU button.
Display inversion mode is for hanging the unit upside down.
Software version
Pan Inversion
Press the MENU button to select
Press the MENU button up to when the
. Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
(normal) or
(pan inversion) mode. Once the mode has been
selected, press the ENTER button to confirm. To go back to the functions
without any changes press the MENU button again. Press and hold the
is showing on the display.
Press the ENTER button and the display will show the version of software of
the unit. To go back to the functions press the MENU button.
Reset
MENU button for one second or wait for one minute to go back to the main
Press the MENU button to select
menu.
channels of the unit will return to their standard position.
Tilt Inversion
Press the MENU button to select
4. How To Control The Unit
. Press the ENTER button and the
display will blink. Use the DOWN and UP buttons to select the
(normal) or
. Press the ENTER button and all
(tilt inversion) mode. Once the mode has been selected,
1. Master/slave built-in preprogram function
2. Universal DMX controller
There is no need to turn the unit off when you change the DMX address as
press the ENTER button to confirm. To go back to the functions without
new DMX address setting will be effected at once. Every time you turn the
any change press the MENU button again. Press and hold the MENU
unit on, it will show “
” on the display and move all the motors to their
‘home’ position and you may hear some noises for about 20 seconds. After
button for one second or wait for one minute to go back to the main menu.
that the unit will be ready to receive a DMX signal or run the built in
programs.
Auto-Test
Press the MENU button to select
. Press the ENTER button and the
4.1 Master/Slave Built In Preprogrammed Function
4.3 DMX Controller
By linking the units in master/slave connection, the first unit will control
By using a universal DMX controller to control the units, you will need to
the other units to give an automatic, sound activated, synchronized light
set a DMX address from 1 to 512 so that the units can receive a DMX signal.
show. This function is good when you want an instant show. You have to
Press the MENU button until
set the first unit as master and select show 1, show 2, show 3 or show
ENTER button and the display will blink. Use the DOWN and UP buttons to
4 from the Show Mode. The other units must be set to either Slave 1
change the DMX-512 address. Once the address has been selected, press
(normal) or Slave 2 (2 light show) mode. A DMX cable between the units
the ENTER button to confirm. To go back to the functions without any
for daisy chaining is needed.
changes press the MENU button again. Press and hold the MENU button
2-light show
one second or wait for one minute to go back to the main menu.
In slave mode, Slave 1 means the unit works normally and Slave 2
Please refer to the below diagram to address your first 4 units:
is showing on the display. Press the
means 2-light show. In order to create a great light show, you can set
Slave 2 on the second unit to get contrast movement to each other, even
Channel
Unit 1
Unit 2
Unit 3
Unit 4
mode
Address
Address
Address
Address
1 channel
1
2
3
4
6 channel
1
7
13
19
Your Slender Beam Bar can be controlled using the optional CA-8 easy
12 channel
1
13
25
37
controller (order code CONT10)
14 channel
1
15
29
43
27 channel
1
28
55
82
if you have two units only.
4.2 CA-8 Controller
BLACKOUT: The fixture can be blacked out by pressing the STANDBY
button. To turn the fixture back on simply press the STANDBY button
again.
MODE (LED OFF): In this mode repeated pressing of the FUNCTION
button will trigger the movement of the heads without any music playing.
MODE (LED FULL ON): In this mode by pressing the FUNCTION button
you can scroll through the four built-in light shows.
MODE (LED SLOW FLASHING): In this mode you can select the speed of
the auto movements. Nine speeds are available (slow>fast)
6 CHANNEL MODE
4.3 DMX 512 Configuration
Channel
1 CHANNEL MODE
Channel
1
Function
Show mode
Value
000-007
008-022
023-037
038-052
053-067
068-082
083-097
098-112
113-127
128-142
143-157
158-172
173-187
188-202
203-217
218-232
233-247
248-255
0
Movement 01
Movement 02
Movement 03
Movement 04
Movement 05
Movement 06
Movement 07
Movement 08
Movement 09
Movement 10
Movement 11
Movement 12
Movement 13
Movement 14
Movement 15
Movement 16
Sound active
Function
1
Dimmer
2
Strobe
Value
0-255 Dimmer 0%-100%
0-007 open
008-255 Strobe Slow>Fast
000-007 Movement 0
008-022 Movement 01
023-037 Movement 02
038-052 Movement 03
053-067 Movement 04
068-082 Movement 05
083-097 Movement 06
098-112 Movement 07
3
Pan/Tilt Movement
113-127 Movement 08
128-142 Movement 09
143-157 Movement 10
158-172 Movement 11
173-187 Movement 12
188-202 Movement 13
203-217 Movement 14
218-232 Movement 15
233-247 Movement 16
248-255 Sound active
4
Movement Speed
000-255 slow to fast
5
LED Chase
000 - 255 LED Chase
6
LED Chase Speed
000 - 255 Chase Speed
12 CHANNEL MODE
11
LED 3
000 - 255 0%~ 100%
Channel
Function
Value
12
Pan4
000 - 255 Pan 0°~ 540°
1
Pan 1
000 - 255 Pan 0°~ 540°
13
Tilt4
000 - 255 Tilt 0°~ 270°
2
Tilt 1
000 - 255 Tilt 0°~ 270°
14
LED 4
000 - 255 0%~ 100%
3
LED 1
000 - 255 0%~ 100%
4
Pan 2
000 - 255 Pan 0°~ 540°
5
Tilt 2
000 - 255 Tilt 0°~ 270°
27 CHANNEL MODE
6
LED 2
000 - 255 0%~ 100%
Channel
Function
Value
7
Pan3
000 – 255 Pan 0°~ 540°
1
Dimmer
000 - 255 0%~ 100%
8
Tilt3
000 – 255 Tilt 0°~ 270°
9
LED 3
000 - 255 0%~ 100%
2
Strobe
000-007 Open
008-255 (Speed 0 - 100%)
10
Pan 4
000 - 255 Pan 0°~ 540°
3
Pan1
000 - 255 Pan 0°~ 540°
11
Tilt 4
000 - 255 Tilt 0°~ 270°
4
Pan fine 1
000 - 255
12
LED 4
000 - 255 0%~ 100%
5
Tilt1
000 - 255 Tilt 0°~ 270°
6
Tilt fine 1
000 - 255
7
Pan Tilt speed1
000 – 255 Fast to slow
8
LED 1
000 - 255 0%~ 100%
9
Pan2
000 - 255 Pan 0°~ 540°
10
Pan fine 2
000 - 255
14 CHANNEL MODE
Channel
Function
Value
11
Tilt2
000 - 255 Tilt 0°~ 270°
1
Dimmer
000 - 255 0%~ 100%
12
Tilt fine 2
000 - 255
2
Strobe
000 - 007 Open
13
Pan Tilt speed2
000 – 255 Fast to slow
008 - 255 (Speed 0 - 100%)
14
LED2
000 - 255 0%~ 100%
3
Pan1
000 - 255 Pan 0°~ 540°
15
Pan3
000 – 255 Pan 0°~ 540°
4
Tilt1
000 - 255 Tilt 0°~ 270°
16
Pan fine 3
000 – 255
5
LED 1
000 - 255 0%~ 100%
6
Pan2
000 - 255 Pan 0°~ 540°
17
Tilt3
000 – 255 Tilt 0°~ 270°
7
Tilt2
000 - 255 Tilt 0°~ 270°
18
Tilt fine 3
000 – 255
8
LED 2
000 - 255 0%~ 100%
19
Pan Tilt speed3
000 – 255 Fast to slow
9
Pan3
000 – 255 Pan 0°~ 540°
20
LED3
000 - 255 0%~ 100%
10
Tilt3
000 – 255 Tilt 0°~ 270°
21
Pan4
000 - 255 Pan 0°~ 540°
22
Pan fine 4
000 - 255
23
Tilt4
000 - 255 Tilt 0°~ 270°
24
Tilt fine 4
000 - 255
25
Pan Tilt speed4
000 – 255 Fast to slow
26
LED4
000 - 255 0%~ 100%
Special
000-199 No function
200-209 Reset
210-239 No function
27
Function
240-255 Stand-alone
4.Trouble shooting
Following are a few common problems that may occur during
operation and some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of the power and the main fuse.
B. Not responding to DMX controller
1. Check DMX cables to see if linked correctly.
2. If the DMX address is showing but no response to the controller, check
the address settings and DMX polarity.
3. Try another DMX controller.
C. No response to the sound
1. Make sure the unit is not receiving a DMX signal.
2. Check the microphone to see if it is good by tapping it. The microphone
is located on the bottom plate of the unit.
5. Fixture Cleaning
The cleaning of external optical lenses must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding
can cause a greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning fluid or mild soapy
water.
Ÿ Always dry the parts carefully.
Ÿ Clean the external optics at least every 20 days.
---------------------www.prolight.co.uk----------------------------------
Download PDF