ECK-161B Embedded System User Manual

ECK-161B Embedded System User Manual
ECK-161B Embedded System
ECK-161B Embedded System
Page i
ECK-161B Embedded System
Revision
Date
Version
Changes
2008-07
1.00
Initial Release
Page ii
ECK-161B Embedded System
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
ECK-161B Embedded System
Manual Conventions
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text. The text is the warning message. A warning message is shown below:
WARNING:
This is an example of a warning message. Failure to adhere to warning
messages may result in permanent damage to the ECK-161B or
personal injury to the user. Please take warning messages seriously.
CAUTION!
Cautionary messages should also be heeded to help reduce the chance of losing data or
damaging the ECK-161B. Cautions are easy to recognize. The word “caution” is written as
“CAUTION,” both capitalized and bold and is followed. The italicized text is the cautionary
message. A caution message is shown below:
Page iv
ECK-161B Embedded System
CAUTION:
This is an example of a caution message. Failure to adhere to cautions
messages may result in permanent damage to the ECK-161B. Please
take caution messages seriously.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
help avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary
message. A note message is shown below:
NOTE:
This is an example of a note message. Notes should always be read.
Notes contain critical information about the ECK-161B. Please take
note messages seriously.
Page v
ECK-161B Embedded System
Packing List
NOTE:
If any of the components listed in the checklist below are missing, please do not
proceed with the installation. Contact the IEI reseller or vendor you purchased
the ECK-161B from or contact an IEI sales representative directly. To contact
an IEI sales representative, please send an email to [email protected]
The items listed below should all be included in the ECK-161B package.
1 x ECK-161B embedded system
1 x Screw set
1 x Power adaptor
1 x Power cord
1 x QIG
2 x Wall mount brackets
1 x HDD installation kit
1 x Driver CD
1 x Manual CD
Images of the above items are shown in Chapter 4.
Page vi
ECK-161B Embedded System
Table of Contents
1
INTRODUCTION..................................................................................................... 1
1.1 ECK-161B EMBEDDED SYSTEM OVERVIEW .............................................................. 2
1.1.1 ECK-161B Benefits ............................................................................................ 3
1.1.2 ECK-161B Features ........................................................................................... 3
1.2 ECK-161B MODEL VARIATION.................................................................................. 3
1.3 TECHNICAL SPECIFICATIONS ...................................................................................... 4
1.4 POWER ADAPTER SPECIFICATIONS ............................................................................. 6
2
MECHANICAL DESCRIPTION............................................................................ 7
2.1 ECK-161B MECHANICAL OVERVIEW ........................................................................ 8
2.2 ECK-161B PHYSICAL DIMENSIONS ........................................................................... 8
2.3 EXTERNAL OVERVIEW ............................................................................................... 9
2.3.1 Front Panel ........................................................................................................ 9
2.3.2 Rear Panel Overview........................................................................................ 10
2.4 INTERNAL OVERVIEW................................................................................................11
3
SYSTEM SPECIFICATIONS ............................................................................... 12
3.1 CPU SUPPORT.......................................................................................................... 13
3.1.1 Intel® Core™ Duo Specifications .................................................................... 13
3.1.2 Intel® Celeron® M Specifications..................................................................... 14
3.2 SYSTEM CHIPSET ..................................................................................................... 14
3.2.1 Northbridge and Southbridge Chipsets ........................................................... 14
3.2.2 Intel® 945GM Northbridge Chipset................................................................. 14
3.2.3 Intel ICH7-M Southbridge Chipset.................................................................. 15
3.3 GRAPHICS SUPPORT ................................................................................................. 16
3.4 ETHERNET CONTROLLER SPECIFICATIONS ............................................................... 16
3.4.1 Overview .......................................................................................................... 16
3.4.2 Features ........................................................................................................... 16
4
INSTALLATION .................................................................................................... 18
4.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 19
Page vii
ECK-161B Embedded System
4.2 INSTALLATION PROCEDURE ...................................................................................... 19
4.2.1 Installation Procedure Overview ..................................................................... 19
4.2.2 Unpacking ........................................................................................................ 20
4.2.3 CompactFlash® Card Installation .................................................................. 21
4.2.4 Bottom Panel Removal..................................................................................... 22
4.2.5 HDD Installation ............................................................................................. 23
4.2.6 PCI Expansion Card Installation..................................................................... 26
4.2.7 ECK-161B Series Wall Mounting..................................................................... 28
4.2.8 Cable Connections ........................................................................................... 29
4.3 POWER-ON PROCEDURE .......................................................................................... 30
4.3.1 Installation Checklist ....................................................................................... 30
4.3.2 Power-on Procedure ........................................................................................ 31
4.4 SYSTEM MAINTENANCE ........................................................................................... 31
5
AMI BIOS SETUP.................................................................................................. 33
5.1 INTRODUCTION ........................................................................................................ 34
5.1.1 Starting Setup................................................................................................... 34
5.1.2 Using Setup ...................................................................................................... 34
5.1.3 Getting Help..................................................................................................... 35
5.1.4 BIOS Menu Bar................................................................................................ 35
5.2 MAIN ....................................................................................................................... 35
5.3 ADVANCED ............................................................................................................... 37
5.3.1 CPU Configuration.......................................................................................... 38
5.3.2 IDE Configuration ........................................................................................... 39
5.3.2.1 IDE Master, IDE Slave ............................................................................. 41
5.3.3 Super IO Configuration.................................................................................... 45
5.3.4 Hardware Health Configuration...................................................................... 47
5.3.5 ACPI Configuration ......................................................................................... 49
5.3.6 APM Configuration.......................................................................................... 51
5.3.7 Remote Access Configuration .......................................................................... 53
5.3.8 USB Configuration........................................................................................... 54
5.4 PCI/PNP .................................................................................................................. 57
5.5 BOOT ....................................................................................................................... 59
5.5.1 Boot Settings Configuration............................................................................. 60
5.6 SECURITY................................................................................................................. 63
Page viii
ECK-161B Embedded System
5.7 CHIPSET ................................................................................................................... 64
5.7.1 North Bridge Configuration............................................................................. 65
5.7.2 South Bridge Configuration............................................................................. 69
5.8 EXIT ......................................................................................................................... 71
6
DRIVER INSTALLATION.................................................................................... 74
6.1 AVAILABLE SOFTWARE DRIVERS .............................................................................. 75
6.2 CHIPSET DRIVER INSTALLATION............................................................................... 75
6.3 VGA DRIVER ........................................................................................................... 78
6.4 BROADCOM LAN DRIVER (FOR GBE LAN) INSTALLATION .................................... 82
6.5 REALTEK HD AUDIO DRIVER (ALC883) INSTALLATION ......................................... 86
6.6 INTEL MATRIX STORAGE MANAGER INSTALLATION ................................................. 90
A
SAFETY PRECAUTIONS..................................................................................... 93
A.1 SAFETY PRECAUTIONS ............................................................................................ 94
A.1.1 General Safety Precautions ............................................................................. 94
A.1.2 Anti-static Precautions .................................................................................... 95
A.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 95
A.2.1 Maintenance and Cleaning.............................................................................. 95
A.2.2 Cleaning Tools ................................................................................................. 96
B
IEI EMBEDDED
SYSTEM SERIES ................................................................. 97
B.1 IEI EMBEDDED SYSTEM SERIES .............................................................................. 98
B.1.1 Overview.......................................................................................................... 98
B.1.2 IEI Embedded System Series ........................................................................... 98
B.1.3 IEI Embedded System Series Variations.......................................................... 99
B.2 EMBEDDED SYSTEM SOLUTIONS ............................................................................. 99
B.2.1 AMD® Geode® LX 800 500 MHz Solutions..................................................... 99
B.2.2 AMD® Geode® GX 466 333 MHz Solutions.................................................. 100
B.2.3 VIA® LUKE® 1GHz Solutions ....................................................................... 100
B.2.4 VIA® MARK® 800MHz Solutions .................................................................. 101
B.2.5 VIA® Eden™ 500 MHz Solutions .................................................................. 101
B.2.6 Intel® Celeron® M 1 GHz Solutions .............................................................. 102
B.2.7 Intel® Celeron® M 1.5GHz Solutions ............................................................ 102
B.2.8 Intel® Pentium® M 1.6GHz Solutions............................................................ 103
B.2.9 Intel® Socket 479 Pentium®/Celeron® M 2GHz Solutions ............................ 103
Page ix
ECK-161B Embedded System
B.2.10 LGA 775 Intel® Pentium® 4/ Pentium® D Solutions ................................... 104
B.2.11 Intel® Socket 479 Core Duo/Solo Solutions................................................. 104
C
BIOS MENU OPTIONS....................................................................................... 105
C.1 BIOS CONFIGURATION OPTIONS ........................................................................... 106
D
WATCHDOG TIMER .......................................................................................... 109
E
ADDRESS MAPPING...........................................................................................112
E.1 IO ADDRESS MAP ...................................................................................................113
E.2 1ST MB MEMORY ADDRESS MAP ...........................................................................114
E.3 IRQ MAPPING TABLE .............................................................................................114
E.4 DMA CHANNEL ASSIGNMENTS ..............................................................................114
F
HAZARDOUS MATERIALS DISCLOSURE ....................................................115
F.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ......................................116
7
INDEX.....................................................................................................................119
Page x
ECK-161B Embedded System
List of Figures
Figure 1-1: ECK-161B Embedded System ..................................................................2
Figure 2-1: ECK-161B Dimensions (mm) ....................................................................9
Figure 2-2: ECK-161B Front Panel.............................................................................10
Figure 2-3: ECK-161B Rear Panel..............................................................................10
Figure 2-4: Internal Overview.....................................................................................11
Figure 4-1: CF Slot Cover Retention Screws............................................................21
Figure 4-2: CF Card Installation.................................................................................21
Figure 4-3: Bottom Panel Retention Screws (Bottom) ............................................22
Figure 4-4: Bottom Panel Retention Screws (Side) .................................................22
Figure 4-5: PCI Card Holder Retention Screws........................................................23
Figure 4-6: HDD Bracket Retention Screws .............................................................24
Figure 4-7: SATA Cable Metal Plate Installation ......................................................24
Figure 4-8: HDD Retention Screws............................................................................25
Figure 4-9: SATA Cable Retention Screws...............................................................25
Figure 4-10: HDD Installation .....................................................................................26
Figure 4-9: PCI Slot Cover Retention Screw ............................................................26
Figure 4-10: PCI Card Holder Retention Screws......................................................27
Figure 4-11: PCI Card Installation..............................................................................27
Figure 4-12: Secure the PCI Card ..............................................................................28
Figure 4-13: Mounting Bracket Retention Screw Holes ..........................................28
Figure 4-14: Wall Mounting Dimensions (mm).........................................................29
Figure 4-15: Power Switch and Power LED..............................................................31
Figure 6-1: InstallShield Wizard Preparation Screen...............................................76
Figure 6-2: Welcome Screen ......................................................................................76
Figure 6-3: License Agreement..................................................................................77
Figure 6-4: Readme Information ................................................................................77
Figure 6-5: Restart the Computer ..............................................................................78
Figure 6-6: Starting Install Shield Wizard Screen ....................................................79
Page xi
ECK-161B Embedded System
Figure 6-7: Preparing Setup Screen ..........................................................................79
Figure 6-8: VGA Driver Installation Welcome Screen..............................................80
Figure 6-9: VGA Driver License Agreement .............................................................80
Figure 6-10: VGA Driver Installing Notice.................................................................81
Figure 6-11: VGA Driver Installation Complete ........................................................81
Figure 6-12: Access Windows Control Panel...........................................................82
Figure 6-13: Double Click the System Icon ..............................................................83
Figure 6-14: Double Click the Device Manager Tab.................................................83
Figure 6-15: Device Manager List ..............................................................................84
Figure 6-16: Search for Suitable Driver.....................................................................84
Figure 6-17: Locate Driver Files.................................................................................85
Figure 6-18: Location Browsing Window..................................................................85
Figure 6-19: Access Windows Control Panel...........................................................86
Figure 6-20: Double Click the System Icon ..............................................................87
Figure 6-21: Double Click the Device Manager Tab.................................................87
Figure 6-22: Device Manager List ..............................................................................88
Figure 6-23: Search for Suitable Driver.....................................................................89
Figure 6-24: Locate Driver Files.................................................................................90
Figure 6-25: Preparing Setup Screen ........................................................................91
Page xii
ECK-161B Embedded System
List of Tables
Table 1-1: Model Variation............................................................................................3
Table 1-2: Technical Specifications ............................................................................5
Table 1-3: Power Adapter Specifications....................................................................6
Table 4-1: Package List Contents..............................................................................20
Table 5-1: BIOS Navigation Keys...............................................................................35
Page xiii
ECK-161B Embedded System
List of BIOS Menus
BIOS Menu 1: Main......................................................................................................36
BIOS Menu 2: Advanced.............................................................................................38
BIOS Menu 3: CPU Configuration..............................................................................39
BIOS Menu 4: IDE Configuration ...............................................................................40
BIOS Menu 5: IDE Master and IDE Slave Configuration..........................................42
BIOS Menu 6: Super IO Configuration ......................................................................46
BIOS Menu 7: Hardware Health Configuration.........................................................48
BIOS Menu 8: ACPI Configuration.............................................................................50
BIOS Menu 9: APM Configuration .............................................................................51
BIOS Menu 10: Remote Access Configuration [Advanced] ...................................53
BIOS Menu 11: USB Configuration............................................................................55
BIOS Menu 12: PCI/PnP Configuration .....................................................................57
BIOS Menu 13: Boot....................................................................................................60
BIOS Menu 14: Boot Settings Configuration............................................................61
BIOS Menu 15: Security..............................................................................................63
BIOS Menu 16: Chipset...............................................................................................65
BIOS Menu 17: North Bridge Chipset Configuration...............................................66
BIOS Menu 18:South Bridge Chipset Configuration ...............................................70
BIOS Menu 19:Exit ......................................................................................................72
Page xiv
ECK-161B Embedded System
Chapter
1
1 Introduction
Page 1
ECK-161B Embedded System
1.1 ECK-161B Embedded System Overview
Figure 1-1: ECK-161B Embedded System
The ECK-161B is an Intel® Core™ Duo or Intel® Celeron® M based embedded system
that is ideal for multimedia applications. The ECK-161B embedded system supports
diverse display including one VGA display and one HDTV display. The High Definition (HD)
Audio integrated in the ECK-161B provides surround sound quality and supports up to
eight channels of sound. A 1 GB DDR2 SDRAM memory module is preinstalled in the
ECK-161B.
The aluminum alloy fins on the chassis offers superior heat dissipation and makes the
fanless ECK-161B embedded system have high performance and low operating
temperature. The ECK-161B has two power input connectors to support 12 V DC input
and 9 V ~ 36 V DC input.
The ECK-161B supports one 2.5” SATA HDD and has one front-accessible
CompactFlash® card slot. Featuring two GbE, six USB, four serial communication ports,
as well as audio, TV-out, and VGA, the ECK-161B offers system integrators and
developers the best selection of robust and high performance computing system platforms.
The ECK-161B embedded system also supports one PCI card for more expansion
options.
Page 2
ECK-161B Embedded System
1.1.1 ECK-161B Benefits
The ECK-161B embedded system has the following benefits:
Easy installation saves installation time
Complete integration saves solution development time and cost
Multiple display interfaces and high quality HD audio support
Powerful preinstalled Intel® Core™ Duo/Celeron® M CPU and motherboard
ensures rigorous processing needs can be met
1.1.2 ECK-161B Features
The ECK-161B has the following features
RoHS compliant design
Fanless system
1.66 GHz Intel® Core™ Duo/1.86 GHz Intel® Celeron® M CPU supported
One PCI expansion card supported
Two GbE RJ-45 connectors supported
VGA and HDTV display interfaces supported
7.1 channel HD audio support
Six USB 2.0 ports and four serial ports
1.2 ECK-161B Model Variation
The ECK-161B embedded system has one preinstalled 1 GB DDR2 SDRAM memory
module preinstalled. The model information is listed in Table 1-1 below.
ECK-161B
CPU
L2 Cache
CPU #
PCI Slot
SF-WD/T2300E/1GB
1.66 GHz Intel® Core™ Duo
2 MB
T2300E
Yes
SF-WD /CM440/1GB
1.86 GHz Intel® Celeron® M
1 MB
440
Yes
Table 1-1: Model Variation
Page 3
ECK-161B Embedded System
1.3 Technical Specifications
The specifications for the Intel based embedded systems are listed below.
ECK-161B
CPU
1.66 GHz Intel® Core™ Duo T2300E CPU with 2 MB L2 cache
1.86 GHz Intel® Celeron® M 440 CPU with 1 MB L2 cache
System Chipset
GMCH: Intel® 945GM
ICH: Intel® ICH7-M
System Memory
One 1 GB DDR2 SDRAM DIMM preinstalled
Ethernet
Two Broadcom PCIe GbE controllers
Display
CRT and TV-out interfaces integrated in Intel® 945GM
1 x 7-pin mini DIN TV-out port
1 x VGA port (DB-15)
USB
Six USB 2.0 supported
(two on the front panel and four on the rear panel)
Serial Port
Four RS-232
Audio
7.1 channel HD audio
Storage
One CompactFlash® card slot
One 2.5” SATA hard disk drive bay
Expansion
One PCI slot
Chassis Construction
Aluminum Alloy with heavy duty metal
Power Input
12 V DC input by 4-pin mini DIN connector
9 ~ 36 V DC input by terminal block
Operating Temperature
0ºC ~ 40ºC (with consumer hard drive)
0ºC ~ 50ºC (with automotive hard drive/CF card)
Page 4
ECK-161B Embedded System
Net Weight (NW/GW)
4.1 kg / 6.0 kg
Dimensions (W x D x H)
222.20 mm x 210.20 mm x 99.49 mm
EMC/Safety
CE, FCC class A
Table 1-2: Technical Specifications
Page 5
ECK-161B Embedded System
1.4 Power Adapter Specifications
The ECK-161B series models are shipped with a 150 W power adapter. The specifications
for the adapter are listed in Table 1-3:
Output
Nominal
12.0 V DC
Regulation
11.4 V – 12.6 V
Output Voltage
380 mV P-P
Output Current
0A
AC Inlet
12.5 A
Short Circuit
Yes
Over-Voltage
Yes
Hold Up
≧3 ms
Min.
90 V
Nominal
100V ~ 240V
Max.
264 V
Frequency
47Hz ~ 63Hz
Protection
Time
Input
≧85% 100 Vac / 7.89 A
Efficiency
≧86% 240 Vac / 7.89 A
Operating
0ºC ~ 40ºC
Storage
-20ºC ~ 80ºC
Relative
Operating (non-condensing)
20% ~ 80%
Humidity
Storage (non-condensing)
10% ~ 90%
MTBF
100,000 hours of continuous operation at 25ºC
Temperature
Environment
Reliability
Table 1-3: Power Adapter Specifications
Page 6
ECK-161B Embedded System
Chapter
2
2 Mechanical
Description
Page 7
ECK-161B Embedded System
2.1 ECK-161B Mechanical Overview
The ECK-161B RoHS compliant, Intel® Core™ Duo/Celeron® M fanless embedded
system features industrial grade components that offer longer operating life, high
shock/vibration resistance and endurance over a wide temperature range. The ECK-161B
combines these features in an aluminum enclosure designed for space critical
applications that require low power consumption. Featuring two GbE, six USB, four serial
communication ports, as well as audio, TV-out, and VGA, the ECK-161B offers system
integrators and developers the best selection of robust and high performance computing
system platforms. The ECK-161B embedded system also supports one PCI card for more
expansion options.
2.2 ECK-161B Physical Dimensions
The dimensions of the ECK-161B are listed below and shown in Figure 2-1.
Height: 99.49 mm
Width: 222.20 mm
Length: 210.20 mm
Page 8
ECK-161B Embedded System
Figure 2-1: ECK-161B Dimensions (mm)
2.3 External Overview
2.3.1 Front Panel
The front panel of the ECK-161B (Figure 2-3) contains following connectors and buttons:
2 x USB 2.0 ports
1 x CompactFlash® slot
1 x Power switch
1 x Reset button
Page 9
ECK-161B Embedded System
1 x HDD LED
1 x Power LED
Figure 2-2: ECK-161B Front Panel
2.3.2 Rear Panel Overview
The rear panel of the ECK-161B contains all the external I/O interface connectors and
power connector. An overview of the rear panel is shown in Figure 2-3 below.
Figure 2-3: ECK-161B Rear Panel
Page 10
ECK-161B Embedded System
The front panel I/O connectors shown in Figure 2-3 are listed below:
1 x 12 V DC inlet
1 x 9 V ~ 36 V DC input terminal block
6 x Audio jacks
1 x Keyboard connector
1 x Mouse connector
1 x PCI expansion card slot
2 x RJ-45 GbE connectors
4 x RS-232 serial port connectors
1 x TV-out connector
4 x USB 2.0 ports
1 x VGA connector
2.4 Internal Overview
The ECK-161B internal components are listed below:
1 x IEI KINO-9452 motherboard (preinstalled)
1 x 1 GB DDR2 SDRAM DIMM module (preinstalled)
1 x 2.5” SATA HDD (optional)
1 x PCI expansion card (optional)
Figure 2-4: Internal Overview
Page 11
ECK-161B Embedded System
Chapter
3
3 System Specifications
Page 12
ECK-161B Embedded System
3.1 CPU Support
NOTE:
The ECK-161B has a preinstalled 1.66 GHz Intel® Core™ Duo or
1.86GHz Intel® Celeron® M CPU. If the CPU fails, the motherboard has
to be replaced. Please contact the IEI reseller or vendor you purchased
the ECK-161B from or contact an IEI sales representative directly. To
contact an IEI sales representative, please send an email to
[email protected]
The KINO-9452 motherboard comes with a preinstalled 1.66 GHz Intel® Core™ Duo or
1.86 GHz Intel® Celeron® M CPU.
3.1.1 Intel® Core™ Duo Specifications
The specifications for the Intel® Core™ Duo processor are listed below
Two complete execution cores in one processor package provide
advancements in simultaneous computing
Dual-core processing efficiently delivers performance while balancing power
requirements
Two execution cores share a high-performance, power-optimized 667 MHz
front-side bus (FSB) to access the same chipset memory.
Enhanced Intel® SpeedStep® technology allows a system to dynamically
adjust processor voltage and core frequency, decreasing average power
consumption and average heat production
Intel® Smart Cache Design allows two execution cores to share 2 MB of L2
cache, reducing FSB traffic and enhancing system responsiveness
Intel® Advanced Thermal Manager supports new digital temperature sensors
and thermal monitors on each execution core to enhance thermal monitoring
accuracy
Streaming SIMD Extensions 3 (SSE3) provides significant performance
enhancement for multi-media applications
Page 13
ECK-161B Embedded System
Embedded lifecycle support protects system investment by enabling extended
product availability for embedded and communications customers
3.1.2 Intel® Celeron® M Specifications
The specifications for the Intel® Celeron® M processor are listed below
Intel® Streaming SIMD Extensions accelerates 3D graphics performance,
video decoding/encoding, and speech recognition.
Advanced power management features
Compatible with IA-32 software.
Advanced branch prediction and data prefetch logic
3.2 System Chipset
3.2.1 Northbridge and Southbridge Chipsets
The following chipsets are preinstalled on the board:
Northbridge: Intel® 945GM
Southbridge: Intel® ICH7-M
The following two sections (Section 3.2.2 and Section 3.2.3) list some of the features of
the Intel® 945GM and the Intel® ICH7-M chipsets. For more information on these two
chipsets please refer to the Intel website.
3.2.2 Intel® 945GM Northbridge Chipset
The Intel® 945GM Northbridge chipset comes with the following features:
System Memory Support
o
o
o
o
o
Supports single/dual-channel DDR2 SDRAM
64-bit wide per channel
256 MB, 512 MB and 1 GB memory technologies supported
Support for DDR2 On-Die Termination (ODT)
Support for 2N timings only
Internal Graphics
o
Page 14
Intel® Gen 3.5 Integrated Graphics Engine
ECK-161B Embedded System
o
250 MHz core render clock and 200 MHz core display clock at 1.05 V
core voltage
o
Supports TV-Out, CRT and SDVO
DMI
o
o
o
o
Chip-to-chip interface between (G)MCH and ICH
Configurable as x2 or x4 DMI lanes
DMI lane reversal support
32-bit downstream address
Power Management
o
o
o
ACPI S0, S3, S4, S5
CPU States C0, C1, C2, C3, C4 states
Rapid Memory Power Mgmt
3.2.3 Intel ICH7-M Southbridge Chipset
The Intel® ICH7-M Southbridge chipset comes with the following features:
PCI Local Bus Specification, Revision 2.3 support for 33 MHz PCI operations
(supports up to six Req/Gnt pairs)
ACPI Power Management Logic support
Enhanced DMA controller, interrupt controller, and timer functions
Integrated Serial ATA host controller with independent DMA operation on two
ports and AHCI
Integrated IDE controller supports Ultra ATA 100/66/33
USB host interface with support for six USB ports; four UHCI host controller;
one EHCI high-speed USB 2.0 Host controller
Integrated Intel® PRO 82573E GbE controller
Supports Audio Codec ’97, Revision 2.3 Specification
Supports Intel® High Definition Audio
Low Pint Count (LPC) interface
Firmware Hub (FWH) interface support
Serial Peripheral Interface (SPI) support
Page 15
ECK-161B Embedded System
3.3 Graphics Support
The graphics features listed below are all integrated on the Intel® 945GM Northbridge
chipset.
Analog CRT
o
o
o
Integrated 400 MHz RAMDAC
Analog monitor support up to QXGA
Support for CRT hot plug
TV-Out
o
o
o
o
Three integrated 10-bit DACS
Overscaling
NTSC/PAL
HDTV support – 480p/720p/1080i/1080p
SDVO Ports
o
o
Concurrent operation of x1 PCIe with SDVO
Two SDVO ports supported
Supports appropriate external SDVO and TV-Out)
3.4 Ethernet Controller Specifications
3.4.1 Overview
The Broadcom BCM5787 is a seventh generation 10/100/1000BASE-T Ethernet LAN
controller solution for high performance network applications. The device combines a
triple-speed IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed
Ethernet transceiver, PCIe bus interface, and on-chip buffer memory in a single device.
The device is fabricated in a 1.2V CMOS process providing a low-power system solution.
The GbE controller features are below.
3.4.2 Features
Integrated 10/100/1000 transceiver
10/100/1000 full/half-duplex MAC
Automatic MDI crossover function
Supports PCIe v1.0a
Page 16
ECK-161B Embedded System
Wake-on-LAN support meeting the ACPI requirements
Statistics for SNMP MIB II, Ethernet-like MIB and Ethernet MIB (802.3z,
clause 30)
Serial EEPROM or serial flash supported
JTAG supported
196-FBGA package
Page 17
ECK-161B Embedded System
Chapter
4
4 Installation
Page 18
ECK-161B Embedded System
4.1 Anti-static Precautions
WARNING:
If the following anti-static precautions are not followed, a user may be
injured and the system irreparably damaged.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the motherboard and the power module. (Dry climates are especially susceptible
to ESD.) It is therefore critical that whenever the ECK-161B is opened and any electrical
component handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board, touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
4.2 Installation Procedure
4.2.1 Installation Procedure Overview
To properly install the ECK-161B, the following steps must be followed. Detailed
descriptions of these instructions are listed in the sections that follow.
Step 1: Unpacking
Step 2: Install the CF card
Step 3: Install the HDD
Step 4: Install the PCI expansion card
Step 5: Mount the ECK-161B
Step 6: Connect the rear panel peripheral connectors
Page 19
ECK-161B Embedded System
Step 7: Power the system upStep 0:
4.2.2 Unpacking
After the ECK-161B is received make sure the following components are included in the
package. If any of these components are missing, please contact the ECK-161B reseller
or vendor where it was purchased or contact an IEI sales representative immediately.
Quantity
Item
1
ECK-161B embedded system
1
Power adaptor
1
Power cord
1
Screw set
1
HDD installation kit
2
Wall mount brackets
1
Driver and manual CD
1
Quick installation guide
Table 4-1: Package List Contents
Page 20
Image
ECK-161B Embedded System
4.2.3 CompactFlash® Card Installation
To install the CF card, please follow the steps below.
Step 1: Locate the CF slot on the front panel of the ECK-161B.
Step 2: Remove the two CF slot cover retention screws from the front panel (Figure
4-1).
Figure 4-1: CF Slot Cover Retention Screws
Step 3: Insert the CF card into the slot (Figure 4-2).
Figure 4-2: CF Card Installation
Step 4: Replace the CF slot cover to protect the CF card and secure the slot cover with
two previously removed retention screws. Step 0:
Page 21
ECK-161B Embedded System
4.2.4 Bottom Panel Removal
Before installing the internal components, the bottom panel must be removed. To remove
the bottom panel, please follow the steps below:
Step 1: Turn the ECK-161B embedded system over.
Step 2: Locate the bottom panel retention screws, four on the bottom panel (Figure 4-3),
two on the right panel and two on the left side panel (Figure 4-4).
Figure 4-3: Bottom Panel Retention Screws (Bottom)
Figure 4-4: Bottom Panel Retention Screws (Side)
Step 3: Remove the eight bottom panel retention screws.
Step 4: Gently remove the bottom panel from the ECK-161B. Step 0:
Page 22
ECK-161B Embedded System
4.2.5 HDD Installation
One 2.5” SATA HDD can be installed in the ECK-161B embedded system. To install the
HDD, follow the instructions below.
Step 1: Remove the bottom panel. See Section 4.2.3.
Step 2: Remove the two PCI card holder retention screws and remove the PCI card
holder (Figure 4-5).
Figure 4-5: PCI Card Holder Retention Screws
Step 3: Remove the HDD bracket by removing the four retention screws (Figure 4-6).
Page 23
ECK-161B Embedded System
Figure 4-6: HDD Bracket Retention Screws
Step 4: Install the metal plate for securing SATA cable. Align the retention screw
holes on the metal plate with the two retention screw holes near the connector
side on the bottom of the HDD. Insert two retention screws to secure the metal
plate with the HDD (Figure 4-7).
Figure 4-7: SATA Cable Metal Plate Installation
Step 5: Secure the HDD with the HDD bracket. Align the retention screw holes on the
sides of the HDD with the retention screw holes on the bracket. Insert four
retention screws from the sides of the bracket to secure the HDD with the
bracket (Figure 4-8).
Page 24
ECK-161B Embedded System
Figure 4-8: HDD Retention Screws
Step 6: Secure the SATA cable to the HDD. Connect the SATA cable from the
ECK-161B to the rear of the HDD. Insert two retention screws to secure the
SATA cable with the HDD (Figure 4-9).
Figure 4-9: SATA Cable Retention Screws
Step 7: Replace the HDD bracket into the ECK-161B and reinsert the four previously
removed retention screws (Figure 4-10).
Page 25
ECK-161B Embedded System
Figure 4-10: HDD Installation
Step 8: Replace the bottom panel. Step 0:
4.2.6 PCI Expansion Card Installation
The ECK-161B has one PCI slot. The PCI expansion card with a depth under 155 mm can
be installed in the ECK-161B. To install the PCI card, follow the instructions below.
Step 1: Remove the bottom panel. See Section 4.2.3.
Step 2: Remove the PCI slot cover on the rear panel of the ECK-161B by removing the
retention screw shown in Figure 4-11.
Figure 4-11: PCI Slot Cover Retention Screw
Page 26
ECK-161B Embedded System
Step 3: Remove the two PCI card holder retention screws (Figure 4-12) and remove the
PCI card holder.
Figure 4-12: PCI Card Holder Retention Screws
Step 4: Insert the PCI card into the PCI slot in the ECK-161B (Figure 4-13).
Figure 4-13: PCI Card Installation
Page 27
ECK-161B Embedded System
Step 5: Secure the PCI card with one retention screws and the cad holder (Figure 4-14).
Step 0:
Figure 4-14: Secure the PCI Card
4.2.7 ECK-161B Series Wall Mounting
To mount the ECK-161B, please follow the steps below.
Step 1: Locate the four ECK-161B series mounting bracket retention screw holes on the
bottom of the chassis. See Figure 4-15.
Figure 4-15: Mounting Bracket Retention Screw Holes
Page 28
ECK-161B Embedded System
Step 2: Align the round retention screws on the first bracket with the ECK-161B
retention screw holes on the bottom of the chassis. Insert one of the retention
screws into each of the retention holes.
Step 3: Align the round retention screws on the second bracket with the ECK-161B
series retention screw holes on the other side of the bottom of the chassis. Insert
one of the retention screws into each of the retention holes.
Step 4: Drill four properly spaced holes into the surface on which the controller is going
to be mounted.
Figure 4-16: Wall Mounting Dimensions (mm)
Step 5: Insert one machine screw into each of the four retention holes on the bracket
and into the wall or surface on which the ECK-161B is mounted.
4.2.8 Cable Connections
Once the system has been mounted on the wall, the following connectors can be
connected to the system.
Audio jacks
Keyboard and mouse connectors
Power input connector
Page 29
ECK-161B Embedded System
RJ-45 connector
Serial port connector
TV-out cable connector
USB devices
VGA devices
The cable connection locations are shown in Figure 2-3.
4.3 Power-On Procedure
4.3.1 Installation Checklist
WARNING:
Make sure a power supply with the correct input voltage is being fed into
the system. Incorrect voltages applied to the system may cause damage to
the internal electronic components and may also cause injury to the user.
The ECK-161B has two power input connectors shown below, one
supports 12 V DC input and the other supports 9 ~ 36 V DC input.
To power on the embedded system please make sure of the following:
The bottom panel is installed
All peripheral devices (monitor, serial communications devices etc.) are
connected
The power cables are plugged in
Page 30
ECK-161B Embedded System
4.3.2 Power-on Procedure
To power-on the ECK-161B please follow the steps below:
Step 6: Turn on the power switch (Figure 4-17).
Step 7: Once turned on, the green power LED on the front panel should be turned on.
Step 0:
Figure 4-17: Power Switch and Power LED
4.4 System Maintenance
WARNING:
Take Anti-Static precautions whenever maintenance is being carried
out on the embedded system components. Failure to take anti-static
precautions can cause permanent embedded system damage.
The embedded system components listed below can all be replaced if they fail:
HDD
PCI card
CF card
Page 31
ECK-161B Embedded System
For the replacement procedures of the component listed above, please refer to
Section 4.2.
A user cannot replace some of the components in the ECK-161B. If the following
components fail it must be shipped back to IEI to be replaced. Please contact the system
vendor, reseller or an IEI sales person directly.
Motherboard
CPU
DIMM
Page 32
ECK-161B Embedded System
Chapter
5
5 AMI BIOS Setup
Page 33
ECK-161B Embedded System
5.1 Introduction
A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup
program allows users to modify the basic system configuration. This chapter describes
how to access the BIOS setup program and the configuration options that may be
changed.
5.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP” message
appears on the screen. 0.
If the message disappears before, restart the computer and try again.
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the “+” and “-“ keys to
change entries, press F1 for help and press ESC to quit. Navigation keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
“+” key
Increase the numeric value or make changes
“-“ key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Page 34
ECK-161B Embedded System
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
5.1.4 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main Changes the basic system configuration.
Advanced Changes the advanced system settings.
PCIPnP Changes the advanced PCI/PnP Settings
Boot Changes the system boot configuration.
Security Sets User and Supervisor Passwords.
Chipset Changes the chipset settings.
Exit Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
5.2 Main
When the BIOS Setup program is entered, the Main menu (BIOS Menu 1) appears. The
Main menu gives an overview of the basic system information.
Page 35
ECK-161B Embedded System
BIOS Menu 1: Main
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
AMI BIOS: Displays auto-detected BIOS information
o
o
o
Version:
Current BIOS version
Build Date: Date the current BIOS version was made
ID:
Installed BIOS ID
Processor: Displays auto-detected CPU specifications
o
o
o
Type: Names the currently installed processor
Speed: Lists the processor speed
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
o
Page 36
Size:
Lists memory size
ECK-161B Embedded System
The System Overview field also has two user configurable fields:
System Time [xx:xx:xx]: The system time is set here.
System Date [Day xx/xx/xxxx]: The system date is set here.
5.3 Advanced
The Advanced menu (BIOS Menu 2) allows access to the CPU and peripheral device
configuration options through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system to
malfunction. Make sure that the settings made are compatible with the
hardware.
CPU Configuration (see Section 5.3.1)
IDE Configuration (see Section 5.3.2)
SuperIO Configuration (see Section 5.3.3)
Hardware Health Configuration (see Section 5.3.4)
ACPI Configuration (see Section 5.3.5)
APM Configuration (see Section 5.3.6)
Remote Access Configuration (see Section 5.3.7)
USB Configuration (see Section 5.3.8)
Page 37
ECK-161B Embedded System
BIOS Menu 2: Advanced
5.3.1 CPU Configuration
The CPU Configuration menu (BIOS Menu 3) shows detailed CPU specifications and
CPU configuration options.
Page 38
ECK-161B Embedded System
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Manufacturer: Lists the name of the CPU manufacturer
Brand String: Lists the brand name of the CPU being used
Frequency: Lists the CPU processing speed
FSB Speed: Lists the FSB speed
Cache L1: Lists the CPU L1 cache size
Cache L2: Lists the CPU L2 cache size
5.3.2 IDE Configuration
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system.
Page 39
ECK-161B Embedded System
BIOS Menu 4: IDE Configuration
ATA/IDE Configuration [Compatible]
The ATA/IDE Configuration BIOS option allows the user to configure the ATA/IDE device
mode.
Disable all ATA/IDE ports. No Primary/Secondary IDE
Disabled
mode is presented for configuration
Compatible
DEFAULT
Up to 4 HDDs can be used, two for SATA and the other
for PATA IDE. If this option is selected, “Legacy IDE
Channels” option is presented for configuration.
Enhanced
If this option is selected, “Configure SATA as” and
“Configure SATA channels” options are presented for
configuration.
Page 40
ECK-161B Embedded System
Legacy IDE Channels [SATA Pri, PATA Sec]
Use the Legacy IDE Channels option configures PATA and SATA resources for operating
systems that require legacy IDE operation.
Enable up to two SATA devices
SATA Only
SATA
Pri,
DEFAULT
PATA Sec
This option allows the system to access the SATA
devices before the primary IDE devices
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. This displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system. If an IDE device is detected, and one of the above
listed four BIOS configuration options are selected, the IDE configuration options shown in
Section 5.3.2.1 appear.
5.3.2.1 IDE Master, IDE Slave
IDE Master and IDE Slave configuration options for both primary and secondary IDE
devices are shown in the BIOS menu below.
Page 41
ECK-161B Embedded System
BIOS Menu 5: IDE Master and IDE Slave Configuration
Type [Auto]
The Type BIOS option determines the type of device that the AMIBIOS attempts to boot
from after the Power-On Self-Test (POST) has completed.
Selecting this value prevents the BIOS from searching
Not Installed
for an IDE disk drive on the specified channel.
Auto
DEFAULT
This selection enables the BIOS to auto detect the
IDE disk drive type attached to the specified channel.
This setting should be used if an IDE hard disk drive is
attached to the specified channel.
CD/DVD
The CD/DVD option specifies that an IDE CD-ROM
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
Page 42
ECK-161B Embedded System
IDE disk drives on the specified channel.
This option specifies an ATAPI Removable Media
ARMD
Device. These include, but are not limited to:
ZIP
LS-120
LBA/Large Mode [Auto]
The LBA/Large Mode BIOS option disables or auto detects LBA (Logical Block
Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
This selection prevents the BIOS from using the LBA
Disabled
mode control on the specified channel.
Auto
DEFAULT
This option allows the BIOS to auto detect the LBA mode
control on the specified channel.
Block (Multi Sector Transfer) [Auto]
Selecting this option prevents the BIOS from using
Disabled
Multi-Sector Transfer on the specified channel. The data
to and from the device occurs one sector at a time.
Auto
DEFAULT
Selecting this value to allows the BIOS to auto detect the
device support for Multi-Sector Transfers on the specified
channel. If supported. Select this value to allow the BIOS
to auto detect the number of sectors per block for transfer
from the hard disk drive to the memory. The data transfer
to and from the device occurs multiple sectors at a time.
Page 43
ECK-161B Embedded System
PIO Mode [Auto]
The PIO Mode option selects the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Auto
DEFAULT
This setting allows the BIOS to auto detect the PIO mode. Use
this value if the IDE disk drive support cannot be determined.
0
PIO mode 0 selected with a maximum transfer rate of 3.3MBps
1
PIO mode 1 selected with a maximum transfer rate of 5.2MBps
2
PIO mode 2 selected with a maximum transfer rate of 8.3MBps
3
PIO mode 3 selected with a maximum transfer rate of 11.1MBps
4
PIO mode 4 selected with a maximum transfer rate of 16.6MBps
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
DMA Mode [Auto]
The DMA Mode BIOS selection adjusts the DMA mode options.
Auto
DEFAULT
The BIOS auto detects the DMA mode. Use this value if the
IDE disk drive support cannot be determined.
S.M.A.R.T [Auto]
Self-Monitoring Analysis and Reporting Technology (SMART) feature can help predict
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Auto
DEFAULT
BIOS to auto detects if the hard disk drive supports
S.M.A.R.T. Use this setting if the IDE disk drive support
Page 44
ECK-161B Embedded System
cannot be determined.
Select this value to prevent the BIOS from using the
Disabled
SMART feature.
Select this value to allow the BIOS to use the SMART
Enabled
feature on support hard disk drives.
32Bit Data Transfer [Enabled]
The 32Bit Data Transfer BIOS option enables or disables 32-bit data transfers.
Prevents the BIOS from using 32-bit data transfers.
Disabled
Enabled
DEFAULT
Allows BIOS to use 32-bit data transfers on support hard
disk drives.
5.3.3 Super IO Configuration
The Super IO Configuration menu (BIOS Menu 6) sets or changes the configurations for
the FDD controllers, parallel ports and serial ports.
Page 45
ECK-161B Embedded System
BIOS Menu 6: Super IO Configuration
Serial Port1 Address [3F8/IRQ4]
The Serial Port1 Address option allows BIOS to select the Serial Port 1 base address.
No base address is assigned to Serial Port 1
Disabled
3F8/IRQ4
DEFAULT
Serial Port 1 I/O port address is 3F8 and the interrupt
address is IRQ4
3E8/IRQ4
Serial Port 1 I/O port address is 3E8 and the interrupt
address is IRQ4
2E8/IRQ3
Serial Port 1 I/O port address is 2E8 and the interrupt
address is IRQ3
Serial Port2 Address [2F8/IRQ3]
The Serial Port2 Address option allows BIOS to select the Serial Port 2 base address.
Page 46
ECK-161B Embedded System
No base address is assigned to Serial Port 2
Disabled
2F8/IRQ3
Serial Port 2 I/O port address is 3F8 and the interrupt
DEFAULT
address is IRQ3
Serial Port 2 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 2 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port3 Address [3E8]
This option allows BIOS to select the base addresses for serial port 3
No base address is assigned to serial port 3
Disabled
3E8
DEFAULT
Serial port 3 I/O port address is 3E8
2E8
Serial port 3 I/O port address is 2E8
2E0
Serial port 3 I/O port address is 2E0
Serial Port4 Address [2E8]
This option allows BIOS to select the base addresses for serial port 4.
Disabled
No base address is assigned to serial port 4
3E8
Serial port 4 I/O port address is 3E8
2E8
2E0
DEFAULT
Serial port 4 I/O port address is 2E8
Serial port 4 I/O port address is 2E0
5.3.4 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 7) shows the operating
temperature, fan speeds and system voltages.
Page 47
ECK-161B Embedded System
BIOS Menu 7: Hardware Health Configuration
CPU FAN Mode Setting: [Full On mode]
The CPU FAN Mode Setting has the following options:
Full On mode
DEFAULT
If selected, there are no additional configurable
options.
Automatic
If selected, the following options will appear with
Mode
values that can be configured:
CPU Temp. Limit of OFF
CPU Temp. Limit of Start
CPU Temp. Limit of Full
CPU Fan Start PWM
Page 48
ECK-161B Embedded System
Slop PWM 1: 0 PWM, 1 PWM (Default),
2 PWM, 4 PWM, 8 PWM, 16 PWM, 32
PWM or 64 PWM
PWM Manually
If selected, the following option will appear with
mode
values that can be configured:
CPU Fan PWM Control
The following system parameters and values are shown. The system parameters that are
monitored are:
System Temperatures: The following system temperatures are monitored
o
o
CPU Temperature
System Temperature
Fan Speeds: The CPU cooling fan speed is monitored.
o
o
CPU Fan Speed
System Fan Speed
Voltages: The following system voltages are monitored
o
o
o
o
o
o
o
o
o
CPU Core
+2.5V
+3.30V
+5.00V
+12.0V
GMCH (1.5V)
1.05V
5VSB
VBAT
5.3.5 ACPI Configuration
The ACPI Configuration menu (BIOS Menu 8) configures the Advanced Configuration
and Power Interface (ACPI) and Power Management (APM) options.
Page 49
ECK-161B Embedded System
BIOS Menu 8: ACPI Configuration
Suspend mode [S3 (STR)]
Use the Suspend Mode option to specify the sleep state the system enters when it is not
being used.
The system enters S1(POS) sleep state. The system
S1 (POS)
appears off. The CPU is stopped; RAM is refreshed; the
system is running in a low power mode.
S3 (STR)
DEFAULT
The system enters a S3(STR) sleep state. The CPU has
no power; RAM is in slow refresh; the power supply is in a
reduced power mode.
Page 50
ECK-161B Embedded System
5.3.6 APM Configuration
Use the APM Configuration menu (BIOS Menu 9) to select the advanced power
management.
BIOS Menu 9: APM Configuration
AT/ATX power [ATX power]
Use the AT/ATX power BIOS option to select the power supply that is connected to the
system.
An AT power supply is connected to the system
AT power
ATX power
DEFAULT
An ATX power supply is connected to the system
Restore on AC Power Loss by IO [Power Off]
The Restore on AC Power Loss by IO BIOS option specifies what state the system
returns to if there is a sudden loss of power to the system.
Page 51
ECK-161B Embedded System
Power Off
DEFAULT
The system remains turned off
The system turns on
Power On
Resume on PME# [Disabled]
The Resume on PME# BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the PCI PME (power management
event) controller.
Disabled
DEFAULT
Wake event not generated by PCI PME controller
activity
Wake event generated by PCI PME controller activity
Enabled
Resume On PCI-Express WAKE# [Enabled]
The Resume On PCI-Express WAKE# BIOS option specifies if the system will be roused
from a suspended or standby state when there is activity on the PCI-Express controller.
Wake event not generated by PCI-Express controller
Disabled
activity
Enabled
DEFAULT
Wake event generated by PCI-Express controller
activity
Resume On RTC Alarm [Disabled]
The Resume On RTC Alarm determines when the computer will be roused from a
suspended state.
Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
Enabled
If selected, the following will appear with values that
can be selected:
Page 52
ECK-161B Embedded System
RTC Alarm Date (Days)
RTC Alarm Time
After setting the alarm, the computer will turn itself on
from a suspend state when the alarm goes off.
5.3.7 Remote Access Configuration
Use the Remote Access Configuration menu (BIOS Menu 10) to configure remote
access parameters. The Remote Access Configuration is an AMIBIOS feature and
allows a remote host running a terminal program to display and configure the BIOS
settings.
BIOS Menu 10: Remote Access Configuration [Advanced]
Page 53
ECK-161B Embedded System
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities
of the system.
Disabled
DEFAULT
Enabled
Remote access is disabled.
Remote access configuration options shown below
appear:
Serial Port Number
Serial Port Mode
Flow Control
Redirection after BIOS POST
Terminal Type
VT-UTF8 Combo Key Support
These configuration options are discussed below.
5.3.8 USB Configuration
Use the USB Configuration menu (BIOS Menu 11) to read USB configuration
information and configure the USB settings.
Page 54
ECK-161B Embedded System
BIOS Menu 11: USB Configuration
USB Configuration
The USB Configuration field shows the system USB configuration. The items listed are:
Module Version: x.xxxxx.xxxxx
USB Devices Enabled
The USB Devices Enabled field lists the USB devices that are enabled on the system
USB Functions [Enabled]
Use the USB Functions BIOS option to enable or disable USB function support.
USB function support disabled
Disabled
Enabled
DEFAULT
USB function support enabled
Page 55
ECK-161B Embedded System
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
Enabled
DEFAULT
USB 2.0 controller enabled
USB 2.0 controller disabled
Disabled
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Legacy USB support disabled
Disabled
Enabled
DEFAULT
Legacy USB support enabled
Legacy USB support disabled if no USB devices are
Auto
connected
USB2.0 Controller Mode [FullSpeed]
Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.
FullSpeed
DEFAULT
HiSpeed
The controller is capable of operating at 12Mb/s
The controller is capable of operating at 480Mb/s
BIOS EHCI Handoff [Enabled]
Use the BIOS EHCI Handoff option for systems running OSes that do not have EHCI
hand-off support. The EHCI ownership change is managed by the EHCI driver.
Page 56
ECK-161B Embedded System
Systems with OSes that do not support EHCI can
Disabled
use the EHCI handoff functionality.
Enabled
DEFAULT
Systems with OSes that do not support EHCI cannot
use the EHCI handoff functionality.
5.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 12) to configure advanced PCI and PnP settings.
WARNING!
Setting wrong values for the BIOS selections in the PCIPnP BIOS menu
may cause the system to malfunction.
BIOS Menu 12: PCI/PnP Configuration
Page 57
ECK-161B Embedded System
IRQ# [Available]
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Available
DEFAULT
The specified IRQ is available to be used by
PCI/PnP devices
The specified IRQ is reserved for use by Legacy ISA
Reserved
devices
Available IRQ addresses are:
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ 11
IRQ 14
IRQ 15
DMA Channel# [Available]
Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP
device.
Available
DEFAULT
The specified DMA is available to be used by
PCI/PnP devices
Reserved
The specified DMA is reserved for use by Legacy
ISA devices
Available DMA Channels are:
DM Channel 0
Page 58
ECK-161B Embedded System
DM Channel 1
DM Channel 3
DM Channel 5
DM Channel 6
DM Channel 7
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that
should be reserved for legacy ISA devices.
Disabled
DEFAULT
No memory block reserved for legacy ISA devices
16K
16KB reserved for legacy ISA devices
32K
32KB reserved for legacy ISA devices
64K
54KB reserved for legacy ISA devices
5.5 Boot
Use the Boot menu (BIOS Menu 13) to configure system boot options.
Page 59
ECK-161B Embedded System
BIOS Menu 13: Boot
5.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 14) to configure advanced
system boot options.
Page 60
ECK-161B Embedded System
BIOS Menu 14: Boot Settings Configuration
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
No POST procedures are skipped
Disabled
Enabled
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
Quiet Boot [Disabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Disabled
Enabled
DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
Page 61
ECK-161B Embedded System
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
The system displays normal information during
Keep Current
system boot.
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Does not enable the keyboard Number Lock automatically. To
Off
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
Boot From LAN Support [Disabled]
The BOOT From LAN Support option enables the system to be booted from a remote
system.
Disabled
Page 62
DEFAULT
Cannot be booted from a remote system through the
ECK-161B Embedded System
LAN
Enabled
Can be booted from a remote system through the
LAN
5.6 Security
Use the Security menu (BIOS Menu 15) to set system and user passwords.
BIOS Menu 15: Security
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
this field and enter the password. After the password has been added, Install appears
next to Change Supervisor Password.
Page 63
ECK-161B Embedded System
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
password. After the password has been added, Install appears next to Change User
Password.
5.7 Chipset
Use the Chipset menu (BIOS Menu 16) to access the Northbridge and Southbridge
configuration menus
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Page 64
ECK-161B Embedded System
BIOS Menu 16: Chipset
5.7.1 North Bridge Configuration
Use the North Bridge Configuration menu (BIOS Menu 17) to configure the northbridge
chipset.
Page 65
ECK-161B Embedded System
BIOS Menu 17: North Bridge Chipset Configuration
Memory Hole [Disabled]
Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA
expansion cards that require a specified area of memory to work properly. If an older ISA
expansion card is used, please refer to the documentation that came with the card to see if
it is necessary to reserve the space.
Disabled
15MB – 16MB
DEFAULT
Memory is not reserved for ISA expansion cards
Between 15MB and 16MB of memory is reserved for
ISA expansion cards
Boots Graphics Adapter Priority [PCI/IGD]
Use the Boots Graphics Adapter Priority option to select the graphics controller used as
the primary boot device. Select either an integrated graphics controller (IGD) or a
combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
Configuration options are listed below:
Page 66
ECK-161B Embedded System
IGD
PCI/IGD
DEFAULT
Internal Graphics Mode Select [Enable, 8MB]
Use the Internal Graphic Mode Select option to specify the amount of system memory
that can be used by the Internal graphics device.
Disable
1MB of memory used by internal graphics device
Enable, 1MB
Enable, 8MB
DEFAULT
8MB of memory used by internal graphics device
DVMT Mode Select [DVMT Mode]
Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology
(DVMT) operating mode.
A fixed portion of graphics memory is reserved as
Fixed Mode
graphics memory.
DVMT Mode
DEFAULT
Graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
Combo Mode
A fixed portion of graphics memory is reserved as
graphics memory. If more memory is needed,
graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
DVMT/FIXED Memory [128MB]
Use the DVMT/FIXED Memory option to specify the maximum amount of memory that
can be allocated as graphics memory. This option can only be configured for if DVMT
Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is
Page 67
ECK-161B Embedded System
selected, the maximum amount of graphics memory is 128MB. Configuration options are
listed below.
64MB
128MB
DEFAULT
Maximum DVMT
Boot Display Device [Auto]
Use the Boot Display Device option to select the display device used by the system
when it boots. Configuration option is listed below.
Auto
DEFAULT
CRT
TV
LFP
Flat Panel Type [1024*768]
Use the Flat Panel Type option to select the type of flat panel connected to the system.
Configuration options are listed below.
1366*768
1920*1080
1024*768
1280*1024 (36bits)
1400*1050 (36bits)
1600*1200 (36bits)
1280*768
1680*1050 (36bits)
1920*1200 (36bits)
1024*768 (48bits)
1440*900 (36bits)
1440*900 (48bits)
1280*800
1280*600
Page 68
DEFAULT
ECK-161B Embedded System
2048*1536 (36bits)
Local Flat Panel Scaling [Auto]
Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel
screen attached to the system.
Auto
DEFAULT
Scaling is automatic
Forced Scaling
Scaling is forced
Disabled
Scaling is disabled
TV Standard [VBIOS-Default]
Use the TV Standard option to select the standard of the television connected to the
system. The configuration options are listed below.
VBIOS-Default
DEFAULT
NTSC
PAL
5.7.2 South Bridge Configuration
The SouthBridge Configuration menu (BIOS Menu 18) the Southbridge chipset to be
configured.
Page 69
ECK-161B Embedded System
BIOS Menu 18:South Bridge Chipset Configuration
ASF Support [Enabled]
Use the ASF Support BIOS option to control the system’s ability to connect to a remote
management server.
Enabled
DEFAULT
The Alert Standard Format (ASF) controller is activated
and can communicate with a remote management
server.
Audio Controller [Azalia]
The Audio Controller option enables or disables the High Definition Audio CODEC.
Azalia
DEFAULT
The Intel High Definition Audio controller automatically
detected and enabled
Page 70
ECK-161B Embedded System
The onboard High Definition Audio controller is disabled
Disabled
OnBoard LAN1 (BCM5787M) [Enabled]
The OnBoard LAN1 (BCM5787M) option enables or disables the onboard LAN1.
Onboard LAN1 controller manually disabled
Disabled
Enabled
DEFAULT
The onboard LAN1 controller automatically detected and
enabled
OnBoard LAN2 (BCM5787M) [Enabled]
The OnBoard LAN2 (BCM5787M) option enables or disables the onboard LAN1.
Onboard LAN2 controller manually disabled
Disabled
Enabled
DEFAULT
The onboard LAN2 controller automatically detected and
enabled
5.8 Exit
Use the Exit menu (BIOS Menu 19) to load default BIOS values, optimal failsafe values
and to save configuration changes.
Page 71
ECK-161B Embedded System
BIOS Menu 19:Exit
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.
Discard Changes and Exit
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
Page 72
ECK-161B Embedded System
Load Optimal Defaults
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Load Failsafe Defaults
Use the Load Failsafe Defaults option to load failsafe default values for each of the
parameters on the Setup menus. F8 key can be used for this operation.
Page 73
ECK-161B Embedded System
Chapter
6
6 Driver Installation
Page 74
ECK-161B Embedded System
6.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product and
is subject to change without prior notice. Visit the IEI website or contact
technical support for the latest updates.
The ECK-161B embedded system has the following software drivers:
Intel Chipset Driver Installation
VGA Utilities Driver
LAN Driver (for GbE LAN) Installation
RealTek Audio Driver (ALC883) Installation
SATA Driver Installation
All drivers can be found on the CD that came with the motherboard. To install the drivers
please follow the instructions in the sections below.
6.2 Chipset Driver Installation
To install the chipset driver, please follow the steps below:
Step 1: Insert the CD into the system that contains the ECK-161B embedded system.
Open the 1-INF directory and locate the icon for the infinst_autol.exe
installation file. Once located, use the mouse to double click the icon.
Step 2: The “InstallShield Wizard Preparation Screen” in Figure 6-1 appears.
Page 75
ECK-161B Embedded System
Figure 6-1: InstallShield Wizard Preparation Screen
Step 3: The “Welcome” window in Figure 6-2 appears next.
Figure 6-2: Welcome Screen
Step 4: Click “NEXT” and the license agreement shown in Figure 6-3 appears.
Page 76
ECK-161B Embedded System
Figure 6-3: License Agreement
Step 5: Agree to the license terms by clicking “YES”. The “Readme” in Figure 6-4
appears.
Figure 6-4: Readme Information
Step 6: Click “YES”. The driver is installed on the computer. After the installation is
complete, the installation complete screen shown in Figure 6-5 appears. Select
Page 77
ECK-161B Embedded System
the preferred option and click “FINISH” to complete the installation process.
Step 0:
Figure 6-5: Restart the Computer
6.3 VGA Driver
To install the VGA driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\2-VGA\WIN2K_XP directory (where X:\ is the system CD drive)
and double-click the win2k_xp1420.exe installation file.
Step 3: The Starting Install Shield Wizard appears (Figure 6-6).
Page 78
ECK-161B Embedded System
Figure 6-6: Starting Install Shield Wizard Screen
Step 4: The Preparing Setup window appears next (Figure 6-7).
Figure 6-7: Preparing Setup Screen
Page 79
ECK-161B Embedded System
Step 5: A Welcome screen shown in Figure 6-8 appears. Click NEXT to continue the
installation.
Figure 6-8: VGA Driver Installation Welcome Screen
Step 6: A license agreement shown in Figure 6-9 appears. Read through the license
agreement.
Figure 6-9: VGA Driver License Agreement
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
Page 80
ECK-161B Embedded System
the “YES” button (Figure 6-9). The installation notice shown in Figure 6-10
appears.
Figure 6-10: VGA Driver Installing Notice
Step 8: After the driver installation process is complete, a confirmation screen shown in
Figure 6-11 appears.
Figure 6-11: VGA Driver Installation Complete
Step 9: The confirmation screen shown in Figure 6-11 allows user to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once
decided when to restart the computer, click the “FINISH” button. Step 0:
Page 81
ECK-161B Embedded System
6.4 Broadcom LAN Driver (for GbE LAN) Installation
To install the Broadcom LAN driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 6-12).
Figure 6-12: Access Windows Control Panel
Step 2: Double click the System icon (Figure 6-13).
Page 82
ECK-161B Embedded System
Figure 6-13: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 6-14).
Figure 6-14: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 6-15).
Page 83
ECK-161B Embedded System
Figure 6-15: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 6-16). Click NEXT to continue.
Figure 6-16: Search for Suitable Driver
Page 84
ECK-161B Embedded System
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 6-17).
Click NEXT to continue.
Figure 6-17: Locate Driver Files
Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx
Drivers” directory (Figure 6-18) in the location browsing window, where “X:\” is
the system CD drive.
Figure 6-18: Location Browsing Window
Page 85
ECK-161B Embedded System
Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to
continue. The driver is installed.Step 0:
6.5 RealTek HD Audio Driver (ALC883) Installation
To install the Realtek High Definition (HD) Audio driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 6-12).
Figure 6-19: Access Windows Control Panel
Step 2: Double click the System icon (Figure 6-13).
Page 86
ECK-161B Embedded System
Figure 6-20: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 6-14).
Figure 6-21: Double Click the Device Manager Tab
Page 87
ECK-161B Embedded System
Step 4: A list of system hardware devices appears (Figure 6-15).
Figure 6-22: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 6-16). Click NEXT to continue.
Page 88
ECK-161B Embedded System
Figure 6-23: Search for Suitable Driver
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 6-17).
Click NEXT to continue.
Page 89
ECK-161B Embedded System
Figure 6-24: Locate Driver Files
Step 8: Select “X:\4-AUDIO\AC-KIT883HD\WIN” directory in the location browsing
window, where “X:\” is the system CD drive (Figure 6-18).
Step 9: Click OK to continue. The driver is installed. Step 0:
Step 1: The confirmation screen offers the option of restarting the computer now or later.
For the settings to take effect, the computer must be restarted. Click FINISH to
restart the computer.Step 0:
6.6 Intel Matrix Storage Manager Installation
To install the Intel Matrix Storage Manager driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\5-SATA\ICH7R directory and double-click the iata60_cd.exe
Page 90
ECK-161B Embedded System
installation file.
Step 3: The Preparing Setup window appears ().
Figure 6-25: Preparing Setup Screen
Step 4: A Welcome screen appears. Click NEXT to continue the installation.
Step 5: A license agreement appears. Read through the license agreement.
Step 6: The “Uninstallation Warning” window appears. Click on the NEXT button to
continue.
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
the “YES” button.
Step 8: The “Choose Destination Location” window appears. Click on the NEXT button to
continue. By default, all installed files are copied to the following path:
<bootdrive>:\Program Files\Intel\Intel(R) Matrix Storage Manager.
Step 9: The “Select Program Folder” window appears. Click on the NEXT button to
continue installing the driver.
Page 91
ECK-161B Embedded System
Step 10: After the driver installation process is complete, a confirmation screen appears.
Step 11: The confirmation screen allows user to restart the computer immediately after
the installation is complete or to restart the computer later. For the settings to
take effect the computer must be restarted. Once decided when to restart the
computer, click the “FINISH” button. Step 0:
Page 92
ECK-161B Embedded System
Appendix
A
A Safety Precautions
Page 93
ECK-161B Embedded System
WARNING:
The precautions outlined in this chapter should be strictly followed.
Failure to follow these precautions may result in permanent damage to
the ECK-161B.
A.1 Safety Precautions
Please follow the safety precautions outlined in the sections that follow:
A.1.1 General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
Follow the electrostatic precautions outlined below whenever the
ECK-161B is opened.
Make sure the power is turned off and the power cord is disconnected
whenever the ECK-161B is being installed, moved or modified.
Do not apply voltage levels that exceed the specified voltage range. Doing so
may cause fire and/or an electrical shock.
Electric shocks can occur if the ECK-161B chassis is opened when the
ECK-161B is running.
Do not drop or insert any objects into the ventilation openings of the
ECK-161B.
If considerable amounts of dust, water, or fluids enter the ECK-161B,
turn off the power supply immediately, unplug the power cord, and contact the
ECK-161B vendor.
DO NOT:
o
o
o
o
Page 94
Drop the ECK-161B against a hard surface.
Strike or exert excessive force onto the LCD panel.
Touch any of the LCD panels with a sharp object
In a site where the ambient temperature exceeds the rated temperature
ECK-161B Embedded System
A.1.2 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
ECK-161B may result in permanent damage to the ECK-161B and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the ECK-161B. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the ECK-161B is opened and any of the electrical components are
handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging any electrical component.
Self-grounding: Before handling any electrical component, touch any
grounded conducting material. During the time the electrical component is
handled, frequently touch any conducting materials that are connected to the
ground.
Use an anti-static pad: When configuring or working with an electrical
component, place it on an antic-static pad. This reduces the possibility of ESD
damage.
Only handle the edges of the electrical component: When handling the
electrical component, hold the electrical component by its edges.
A.2 Maintenance and Cleaning Precautions
When maintaining or cleaning the ECK-161B, please follow the guidelines below.
A.2.1 Maintenance and Cleaning
Prior to cleaning any part or component of the ECK-161B, please read the details below.
Except for the LCD panel, never spray or squirt liquids directly onto any other
components. To clean the LCD panel, gently wipe it with a piece of soft dry
cloth or a slightly moistened cloth.
Page 95
ECK-161B Embedded System
The interior of the ECK-161B does not require cleaning. Keep fluids away
from the ECK-161B interior.
Be cautious of all small removable components when vacuuming the
ECK-161B.
Turn the ECK-161B off before cleaning the ECK-161B.
Never drop any objects or liquids through the openings of the ECK-161B.
Be cautious of any possible allergic reactions to solvents or chemicals used
when cleaning the ECK-161B.
Avoid eating, drinking and smoking within vicinity of the ECK-161B.
A.2.2 Cleaning Tools
Some components in the ECK-161B may only be cleaned using a product specifically
designed for the purpose. In such case, the product will be explicitly mentioned in the
cleaning tips. Below is a list of items to use when cleaning the ECK-161B.
Cloth – Although paper towels or tissues can be used, a soft, clean piece of cloth
is recommended when cleaning the ECK-161B.
Water or rubbing alcohol – A cloth moistened with water or rubbing alcohol can
be used to clean the ECK-161B.
Using solvents – The use of solvents is not recommended when cleaning the
ECK-161B as they may damage the plastic parts.
Vacuum cleaner – Using a vacuum specifically designed for computers is one of
the best methods of cleaning the ECK-161B. Dust and dirt can restrict the airflow
in the ECK-161B and cause its circuitry to corrode.
Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are
excellent tools for wiping hard to reach areas.
Foam swabs - Whenever possible, it is best to use lint free swabs such as foam
swabs for cleaning.
Page 96
ECK-161B Embedded System
Appendix
B
B IEI Embedded
System Series
Page 97
ECK-161B Embedded System
B.1 IEI Embedded System Series
B.1.1 Overview
IEI embedded industrial PC systems are ideal for manufacturing and automation
environments where heavy processing demands exist. These systems are designed to
operate effectively within high-stress environments that have diverse operational
conditions. This appendix introduces the full range of IEI embedded systems.
B.1.2 IEI Embedded System Series
The embedded system series are:
ECW-180A
ECW-180B
ECW-181A
ECW-181B
ECW-281BB6
ECN-171B
ECN-171B
ECK-161B
ECK-3688G
ECK-3699G
ECK-3692G
IBX-100-GX2
IBX-100-LX2
IBX-500A
IBX-520CX
IBX-650A
Page 98
ECK-161B Embedded System
B.1.3 IEI Embedded System Series Variations
The differences between the series are listed below.
Motherboard
Cooling
CompactFlash
Drive Bays
ECW-180A
WAFER
Two cooling fans
One CF slot
None
ECW-180B
WAFER
Fanless
One CF slot
None
ECW-181A
WAFER
Two cooling fans
One CF slot
Two 2.5” drive bays
ECW-181B
WAFER
Fanless
One CF slot
Two 2.5” drive bays
ECN-171B
NANO
Fanless
One CF slot
None
ECN-171B
NANO
Fanless
One CF slot
One 2.5” drive bay
ECK-161B
KINO
Fanless
One CF slot
One 2.5” drive bay
ECK-3688G
NANO
One cooling fan
None
One 2.5” drive bay
ECK-3699G
NANO
Two cooling fans
None
ECK-3692G
KINO
Fanless
None
One 2.5” drive bay
IBX-100
NANO
Fanless
One CF slot
One 2.5” drive bay
IBX-500A
AFLMB-LX-800
Fanless
One CF slot
None
IBX-520CX
AFLMB-CX700
Fanless
One CF slot
IBX-650A
NANO
Fanless
One CF slot
One 2.5” drive bay
(optional)
One SATA drive
supported
One 2.5” drive bay
Table B-1: Embedded System Series Overview
B.2 Embedded System Solutions
The different IEI Embedded System solutions are listed below. For further information,
please contact an IEI distributor, reseller, vendor or IEI sales representative. Please also
visit the IEI website (www.ieiworld.com).
B.2.1 AMD® Geode® LX 800 500 MHz Solutions
All the models listed in the table below support an AMD® Geode® LX 800 500 MHz CPU.
Page 99
ECK-161B Embedded System
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECW-180AS1
AMD® CS5536
12V
Two
None
®
ECW-180AS1WD
AMD CS5536
9V ~ 36V
Two
None
ECW-180BS1
AMD® CS5536
12V
None
None
ECW-180BS1WD
AMD® CS5536
9V ~ 36V
None
None
ECW-181AS1
AMD® CS5536
12V
Two
Two 2.5” HDD
ECW-181AS1WD
AMD® CS5536
9V ~ 36V
Two
Two 2.5” HDD
®
ECW-181BS1
AMD CS5536
12V
None
Two 2.5” HDD
ECW-181BS1WD
AMD® CS5536
9V ~ 36V
None
Two 2.5” HDD
ECK-3688GA
AMD® CS5536
12V
One
One 2.5” HDD
®
IBX-100-LX2
AMD CS5536
5V
None
One 2.5” HDD
IBX-500A
AMD® CS5536
12V
None
None
Table B-2: AMD® Geode® LX 800 Embedded System Solutions
B.2.2 AMD® Geode® GX 466 333 MHz Solutions
All the models listed in the table below support an AMD® Geode® GX 466 333 MHz CPU.
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECW-180AS2
AMD® CS5536
12V
Two
None
ECW-180AS2WD
AMD® CS5536
9V ~ 36V
Two
None
®
ECW-180BS2
AMD CS5536
12V
None
None
ECW-180BS2WD
AMD® CS5536
9V ~ 36V
None
None
ECW-181AS2
AMD® CS5536
12V
Two
Two 2.5” HDD
®
ECW-181AS2WD
AMD CS5536
9V ~ 36V
Two
Two 2.5” HDD
ECW-181BS2
AMD® CS5536
12V
None
Two 2.5” HDD
ECW-181BS2WD
AMD® CS5536
9V ~ 36V
None
Two 2.5” HDD
IBX-100-GX2
AMD® CS5536
5V
None
One 2.5” HDD
Table B-3: AMD® Geode® GX466 Embedded System Solutions
B.2.3 VIA® LUKE® 1GHz Solutions
All the models listed in the table below support a VIA® LUKE® 1 GHz CPU.
Page 100
ECK-161B Embedded System
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECW-180AS3
VIA® VT8237R+
12V
Two
None
ECW-180AS3WD
VIA® VT8237R+
9V ~ 36V
Two
None
ECW-180BS3
VIA® VT8237R+
12V
None
None
®
ECW-180BS3WD
VIA VT8237R+
9V ~ 36V
None
None
ECW-181AS3
VIA® VT8237R+
12V
Two
Two 2.5” HDD
ECW-181AS3WD
VIA® VT8237R+
9V ~ 36V
Two
Two 2.5” HDD
®
ECW-181BS3
VIA VT8237R+
12V
None
Two 2.5” HDD
ECW-181BS3WD
VIA® VT8237R+
9V ~ 36V
None
Two 2.5” HDD
ECK-3688GB
VIA® VT8237R+
12V
One
One 2.5” HDD
Table B-4: VIA® LUKE® Embedded System Solutions
B.2.4 VIA® MARK® 800MHz Solutions
All the models listed in the table below support a VIA® MARK® 800 MHz CPU.
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECW-180AS4
VIA® VT82C686B
12V
Two
None
ECW-180AS4WD
VIA® VT82C686B
9V ~ 36V
Two
None
ECW-180BS4
VIA® VT82C686B
12V
None
None
ECW-180BS4WD
VIA® VT82C686B
9V ~ 36V
None
None
®
ECW-181AS4
VIA VT82C686B
12V
Two
Two 2.5” HDD
ECW-181AS4WD
VIA® VT82C686B
9V ~ 36V
Two
Two 2.5” HDD
ECW-181BS4
VIA® VT82C686B
12V
None
Two 2.5” HDD
9V ~ 36V
None
Two 2.5” HDD
ECW-181BS4WD
®
VIA VT82C686B
Table B-5: VIA® MARK® Embedded System Solutions
B.2.5 VIA® Eden™ 500 MHz Solutions
All the models listed in the table below support a VIA® Eden™ 500 MHz CPU.
Page 101
ECK-161B Embedded System
Model Number
System Chipset
DC Input
Fan
Drive Bays
IBX-520CX
VIA® CX700M
12V
None
One SATA drive supported
Table B-6: VIA® MARK® Embedded System Solutions
B.2.6 Intel® Celeron® M 1 GHz Solutions
The model listed in the table below support an Intel® Celeron® M 1 GHz zero cache CPU.
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECW-281BB6
Intel® 852GM + ICH4
12V
No
One 2.5” HDD
Table B-7: Intel® Celeron® M 1 GHz Solutions
B.2.7 Intel® Celeron® M 1.5GHz Solutions
All the models listed in the table below support an Intel® Celeron® M 1.5 GHz CPU.
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECW-180AS5X
SiS 661CX + SiS 964
12V
Two
None
ECW-180AS5XWD
SiS 661CX + SiS 964
9V ~ 36V
Two
None
ECW-181AS5X
SiS 661CX + SiS 964
12V
Two
Two 2.5” HDD
ECW-181AS5XWD
SiS 661CX + SiS 964
9V ~ 36V
Two
Two 2.5” HDD
ECN-171BSE0-CM15G
Intel® 852GM + ICH4
12V
None
None
ECN-171BSE0-WD-CM15G
Intel® 852GM + ICH4
9V ~ 36V
None
None
ECN-171BSEA-CM15G
Intel® 852GM + ICH4
12V
None
None
ECN-171BSEA-WD-CM15G
Intel® 852GM + ICH4
9V ~ 36V
None
None
ECN-171BSEB-CM15G
Intel® 852GM + ICH4
12V
None
None
ECN-171BSEB-WD-CM15G
Intel® 852GM + ICH4
9V ~ 36V
None
None
ECN-171BSE0-CM15G
Intel® 852GM + ICH4
12V
None
One 2.5” HDD
ECN-171BSE0-WD-CM15G
Intel® 852GM + ICH4
9V ~ 36V
None
One 2.5” HDD
ECN-171BSEA-CM15G
Intel® 852GM + ICH4
12V
None
One 2.5” HDD
ECN-171BSEA-WD-CM15G
Intel® 852GM + ICH4
9V ~ 36V
None
One 2.5” HDD
ECN-171BSEB-CM15G
Intel® 852GM + ICH4
12V
None
One 2.5” HDD
ECN-171BSEB-WD-CM15G
Intel® 852GM + ICH4
9V ~ 36V
None
One 2.5” HDD
ECK-3688GDX
SiS 661CX + SiS 964
12V
One
One 2.5” HDD
Page 102
ECK-161B Embedded System
Model Number
System Chipset
DC Input
Fan
Drive Bays
(optional)
Table B-8: Intel® Celeron® M 1.5GHz Solutions
B.2.8 Intel® Pentium® M 1.6GHz Solutions
All the models listed in the table below support an Intel® Pentium® M 1.6GHz CPU.
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECN-171BSE0-PM16G
Intel® 852GM + ICH4
12V
None
None
ECN-171BSE0-WD-PM16G
Intel® 852GM + ICH4
9V ~ 36V
None
None
ECN-171BSEC-PM16G
Intel® 852GM + ICH4
12V
None
None
ECN-171BSEC-WD-PM16G
Intel® 852GM + ICH4
9V ~ 36V
None
None
ECN-171BSE0-PM16G
Intel® 852GM + ICH4
12V
None
One 2.5” HDD
ECN-171BSE0-WD-PM16G
Intel® 852GM + ICH4
9V ~ 36V
None
One 2.5” HDD
ECN-171BSEC-PM16G
Intel® 852GM + ICH4
12V
None
One 2.5” HDD
Intel® 852GM + ICH4
9V ~ 36V
None
One 2.5” HDD
ECN-171BSEC-WD-PM16G
®
®
Table B-9: Intel Pentium M Embedded System Solutions
B.2.9 Intel® Socket 479 Pentium®/Celeron® M 2GHz Solutions
All the models listed in the table below support an Intel® Socket 479 Pentium®/Celeron® M
2GHz CPU with a 400/533MHz FSB (front side bus).
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECW-180AS5S
SiS 661CX + SiS 964
12V
Two
None
ECW-180AS5SWD
SiS 661CX + SiS 964
9V ~ 36V
Two
None
ECW-181AS5S
SiS 661CX + SiS 964
12V
Two
Two 2.5” HDD
ECW-181AS5SWD
SiS 661CX + SiS 964
9V ~ 36V
Two
Two 2.5” HDD
ECK-3688GDS
SiS 661CX + SiS 964
12V
One
One 2.5” HDD (optional)
Table B-10: Intel® Socket 479 Pentium®/Celeron® M Embedded System Solutions
Page 103
ECK-161B Embedded System
B.2.10 LGA 775 Intel® Pentium® 4/ Pentium® D Solutions
All the models listed in the table below support a LGA 775 Intel® Pentium® 4/ Pentium® D
CPU.
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECK-3699GE
Intel® 945G + ICH7
19V DC
Two
One 2.5” HDD (optional)
ECK-3699GH
SiS 661CX + SiS 966
19V DC
Two
One 2.5” HDD (optional)
Table B-11: LGA 775 Intel® Pentium® 4/ Pentium® D System Solutions
B.2.11 Intel® Socket 479 Core Duo/Solo Solutions
All the models listed in the table below support an Intel® Socket 479 Core Duo/Solo CPU
with a 667MHz FSB (front side bus).
Model Number
System Chipset
DC Input
Fan
Drive Bays
ECK-3699GF
Intel® 945GM + ICH7-M
19V DC
Two
One 2.5” HDD (optional)
Table B-12: Intel® Socket 479 Core Duo/Solo System Solutions
Page 104
ECK-161B Embedded System
Appendix
C
C BIOS Menu Options
Page 105
ECK-161B Embedded System
C.1 BIOS Configuration Options
Below is a list of BIOS configuration options described in Chapter 5.
System Overview ...................................................................................................36
ATA/IDE Configuration [Compatible]...................................................................40
Legacy IDE Channels [SATA Pri, PATA Sec]......................................................41
IDE Master and IDE Slave .....................................................................................41
Type [Auto] .............................................................................................................42
ZIP 43
LS-120 .....................................................................................................................43
LBA/Large Mode [Auto].........................................................................................43
Block (Multi Sector Transfer) [Auto] ....................................................................43
PIO Mode [Auto].....................................................................................................44
DMA Mode [Auto]...................................................................................................44
S.M.A.R.T [Auto].....................................................................................................44
32Bit Data Transfer [Enabled] ..............................................................................45
Serial Port1 Address [3F8/IRQ4] ..........................................................................46
Serial Port2 Address [2F8/IRQ3] ..........................................................................46
Serial Port3 Address [3E8]....................................................................................47
Serial Port4 Address [2E8]....................................................................................47
CPU FAN Mode Setting: [Full On mode] .............................................................48
CPU Temp. Limit of OFF .......................................................................................48
CPU Temp. Limit of Start ......................................................................................48
CPU Temp. Limit of Full ........................................................................................48
CPU Fan Start PWM ...............................................................................................48
Slop PWM 1: 0 PWM, 1 PWM (Default), 2 PWM, 4 PWM, 8 PWM, 16 PWM, 32
PWM or 64 PWM ..........................................................................................................49
CPU Fan PWM Control ..........................................................................................49
Suspend mode [S3 (STR)].....................................................................................50
AT/ATX power [ATX power] ..................................................................................51
Restore on AC Power Loss by IO [Power Off] ....................................................51
Page 106
ECK-161B Embedded System
Resume on PME# [Disabled] ................................................................................52
Resume On PCI-Express WAKE# [Enabled] .......................................................52
Resume On RTC Alarm [Disabled].......................................................................52
RTC Alarm Date (Days) .........................................................................................53
RTC Alarm Time .....................................................................................................53
Remote Access [Disabled]....................................................................................54
Serial Port Number ................................................................................................54
Serial Port Mode.....................................................................................................54
Flow Control ...........................................................................................................54
Redirection after BIOS POST................................................................................54
Terminal Type.........................................................................................................54
VT-UTF8 Combo Key Support ..............................................................................54
USB Configuration.................................................................................................55
USB Devices Enabled............................................................................................55
USB Functions [Enabled]......................................................................................55
USB 2.0 Controller [Enabled]................................................................................56
Legacy USB Support [Enabled]............................................................................56
USB2.0 Controller Mode [FullSpeed] ...................................................................56
BIOS EHCI Handoff [Enabled] ..............................................................................56
IRQ# [Available]...................................................................................................58
DMA Channel# [Available] ....................................................................................58
Reserved Memory Size [Disabled] .......................................................................59
Quick Boot [Enabled] ............................................................................................61
Quiet Boot [Disabled] ............................................................................................61
AddOn ROM Display Mode [Force BIOS] ............................................................62
Bootup Num-Lock [On] .........................................................................................62
Boot From LAN Support [Disabled] .....................................................................62
Change Supervisor Password..............................................................................63
Change User Password.........................................................................................64
Memory Hole [Disabled]........................................................................................66
Boots Graphics Adapter Priority [PCI/IGD].........................................................66
Page 107
ECK-161B Embedded System
Internal Graphics Mode Select [Enable, 8MB] ....................................................67
DVMT Mode Select [DVMT Mode].........................................................................67
DVMT/FIXED Memory [128MB] .............................................................................67
Boot Display Device [Auto]...................................................................................68
Flat Panel Type [1024*768]....................................................................................68
Local Flat Panel Scaling [Auto] ............................................................................69
TV Standard [VBIOS-Default]................................................................................69
ASF Support [Enabled] .........................................................................................70
Audio Controller [Azalia].......................................................................................70
OnBoard LAN1 (BCM5787M) [Enabled] ...............................................................71
OnBoard LAN2 (BCM5787M) [Enabled] ...............................................................71
Save Changes and Exit .........................................................................................72
Discard Changes and Exit ....................................................................................72
Discard Changes....................................................................................................72
Load Optimal Defaults...........................................................................................73
Load Failsafe Defaults...........................................................................................73
Page 108
ECK-161B Embedded System
Appendix
D
D Watchdog Timer
Page 109
ECK-161B Embedded System
NOTE:
The following discussion applies to DOS environment.
IEI support is
contacted or the IEI website visited for specific drivers for more
sophisticated operating systems, e.g., Windows and Linux.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMI or a software bug. When the CPU stops working correctly,
Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt
(NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer:
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table D-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. While the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the Watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 110
ECK-161B Embedded System
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system resets.
Example program:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
EXIT_AP, 1
JNE
W_LOOP
;is the application over?
;No, restart the application
MOV
AX, 6F02H
;disable Watchdog Timer
MOV
BL, 0
;
INT
15H
;
; EXIT ;
Page 111
ECK-161B Embedded System
Appendix
D
E Address Mapping
Page 112
ECK-161B Embedded System
E.1 IO Address Map
I/O address
Range
Description
000-01F
DMA Controller
020-021
Interrupt Controller
040-043
System time
060-06F
Keyboard Controller
070-07F
System CMOS/Real time Clock
080-09F
DMA Controller
0A0-0A1
Interrupt Controller
0C0-0DF
DMA Controller
0F0-0FF
Numeric data processor
1F0-1F7
Primary IDE Channel
3B0-3BB
Graphics Controller
3C0-3DF
Graphics Controller
3F6-3F6
Primary IDE Channel
3F7-3F7
Standard floppy disk controller
3F8-3FF
Serial Port 1 (COM1)
Table E-1: IO Address Map
Page 113
ECK-161B Embedded System
E.2 1st MB Memory Address Map
Memory address
Description
00000-9FFFF
System memory
A0000-BFFFF
VGA buffer
F0000-FFFFF
System BIOS
1000000-
Extend BIOS
Table E-2: 1st MB Memory Address Map
E.3 IRQ Mapping Table
IRQ0
System Timer IRQ8
RTC clock
IRQ1
Keyboard
IRQ9
ACPI
IRQ2
Available
IRQ10
LAN
IRQ3
COM2
IRQ11
LAN/USB2.0/SATA
IRQ4
COM1
IRQ12
PS/2 mouse
IRQ5
SMBus Controller IRQ13
FPU
IRQ6
FDC
IRQ14
Primary IDE
IRQ7
Available
IRQ15
Secondary IDE
Table E-3: IRQ Mapping Table
E.4 DMA Channel Assignments
Channel
Function
0
Available
1
Available
2
Floppy disk (8-bit transfer)
3
Available
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
Table E-4: DMA Channel Assignments Table
Page 114
ECK-161B Embedded System
Appendix
E
F Hazardous Materials
Disclosure
Page 115
ECK-161B Embedded System
F.1 Hazardous Material Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 116
ECK-161B Embedded System
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl Ethers
(CR(VI))
(PBB)
(PBDE)
Housing
X
O
O
O
O
X
Display
X
O
O
O
O
X
Printed Circuit
X
O
O
O
O
X
Metal Fasteners
X
O
O
O
O
O
Cable Assembly
X
O
O
O
O
X
Fan Assembly
X
O
O
O
O
X
Power Supply
X
O
O
O
O
X
O
O
O
O
O
Board
Assemblies
Battery
O
O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below
the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part
is above the limit requirement in SJ/T11363-2006
Page 117
ECK-161B Embedded System
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些
元件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
(PBDE)
壳体
X
O
O
O
O
X
显示
X
O
O
O
O
X
印刷电路板
X
O
O
O
O
X
金属螺帽
X
O
O
O
O
O
电缆组装
X
O
O
O
O
X
风扇组装
X
O
O
O
O
X
电力供应组装
X
O
O
O
O
X
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 118
ECK-161B Embedded System
7 Index
Page 119
ECK-161B Embedded System
A
I
Advanced Power Management .................70
ALC883................................................75, 86
AMI BIOS.............................................34, 36
anti-static precautions
anti-static pad .................................. 95
anti-static wristband ........................ 95
handling........................................... 95
self-grounding ................................. 95
I/O interface connectors, external..............10
ICH7-M................................................ 14, 15
Installation Checklist ..................................30
Intel 945GM ........................................ 14, 16
L
L1 cache ....................................................39
L2 cache ....................................................39
C
CD-ROM ..............................................42, 44
CF card ......................................4, 19, 21, 31
N
Northbridge ................................................14
CompactFlash® .............................2, 4, 9, 21
CPU Support..............................................13
O
D
On-Die Termination ....................................14
DDR2 .........................................................14
P
Dimensions ..........................................5, 8, 9
DMA controller ...........................................15
DMI lane ....................................................15
PCI .................................... 15, 35, 52, 57, 58
PCI card .................... 2, 8, 23, 26, 27, 28, 31
power adapter ..............................................6
E
Power-On Procedure .................................30
electrostatic discharge ...............................19
R
external I/O interface connectors...............10
RAMDAC ...................................................16
H
rear panel...................................................10
RJ-45 GbE connectors ..............................11
HD audio..................................................3, 4
HDTV .................................................2, 3, 16
High Definition Audio .....................15, 70, 71
Page 120
ECK-161B Embedded System
S
TV-Out................................................. 15, 16
Safety Precautions.....................................94
U
SATA HDD .......................................2, 11, 23
SDVO...................................................15, 16
SuperIO .....................................................37
T
TV-out ......................................2, 4, 8, 11, 30
unpacking...................................................20
USB 2.0............................................... 15, 56
W
Wall Mounting ............................................28
Page 121
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement