Amana AMVM97 Owners Manual

GAS-FIRED WARM AIR FURNACE
USER’S INFORMATION MANUAL
WARNING
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE.
• DO NOT TRY TO LIGHT ANY APPLIANCE.
• DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE
ANY PHONE IN YOUR BUILDING.
I
• MMEDIATELY CALL YOUR GAS SUPPLIER FROM A
NEIGHBOR’S PHONE. FOLLOW THE GAS SUPPLIER’S
.
• IINSTRUCTIONS
F YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE
FIRE DEPARTMENT.
INSTALLATION AND SERVICE MUST BE PERFORMED BY A
QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS
Installer - Affix this manual, Installation Guide, and Warranty adjacent to the appliance.
Owner - Read and keep all product literature in a safe place for future reference.
WARNING
WARNING
SHOULD
OVERHEATING OCCUR OR THE GAS SUPPLY FAIL
TO SHUT OFF, TURN OFF THE MANUAL GAS SHUTOFF VALVE
EXTERNAL TO THE FURNACE BEFORE TURNING OFF THE
ELECTRICAL SUPPLY.
TO
PREVENT POSSIBLE PROPERTY DAMAGE, PERSONAL
INJURY OR DEATH DUE TO ELECTRICAL SHOCK, THE
FURNACE MUST BE LOCATED TO PROTECT THE ELECTRICAL
COMPONENTS FROM WATER .
WARNING
PRODUCT
CONTAINS FIBERGLASS WOOL. DISTURBING THE
INSULATION IN THIS PRODUCT DURING INSTALLATION ,
MAINTENANCE OR REPAIR WILL EXPOSE YOU TO
FIBERGLASS WOOL. BREATHING THIS MAY CAUSE LUNG
CANCER. (FIBERGLASS WOOL IS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER.) TO REDUCE EXPOSURE
OR FOR FURTHER INFORMATION , CONSULT MATERIAL
SAFETY DATA SHEETS AVAILABLE FROM THE ADDRESS
SHOWN BELOW.
RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.
Due to policy of continual product
improvement, the right is reserved to
change specifications and design
without notice.
HI-131
7/2014
5151 San Felipe Suite 500
Houston, TX 77056
www.goodmanmfg.com • www.amana-hac.com
© 2014 Goodman Manufacturing Company, L.P.
is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
Contents
IMPORTANT NOTE TO THE OWNER REGARDING PRODUCT WARRANTY .......................................................................... 3
UNIT LOCATION ................................................................................................................................................. 3
UNIT INSTALLATION ............................................................................................................................................. 4
Air Requirements ............................................................................................................................................................... 4
Combustion Air .................................................................................................................................................................. 4
Indoor Humidity .................................................................................................................................................................. 5
Propane (LP) Gas Installations Only ................................................................................................................................. 5
THERMOSTAT FUNCTIONS ..................................................................................................................................... 5
Furnace Operation ............................................................................................................................................................. 6
FURNACE START-UP .......................................................................................................................................... 6
FURNACE SHUT DOWN ....................................................................................................................................... 6
LOCKOUT RESET ............................................................................................................................................... 7
Routine Maintenance ......................................................................................................................................................... 7
ANNUAL INSPECTION ........................................................................................................................................... 7
MOTORS ........................................................................................................................................................... 7
FILTERS ............................................................................................................................................................ 7
Troubleshooting / Before You Request a Service Call .................................................................................................... 8
Safety Labels ...................................................................................................................................................................... 9
2
Dear Homeowner, please recognize the following safety information. This information will alert you to the potential for
personal injury.
2. Do not store or use chlorine or fluorine products (bleaches,
cements, strippers, aerosols) near the unit. They can corrode the heat exchanger.
3. Do not use the furnace closet as storage for brooms,
mops, brushes and oily rags or cloths. The area must be
kept clear, clean and free of lint. Furnace must be kept
free and clear of exposed or loose insulation materials in
the area of installation. Examine the furnace area when
the furnace or additional insulation is added since some
insulation materials may be combustible.
WARNING - Indicate hazards or unsafe practices which
COULD result in severe personal injury or death.
WARNING
THIS
PRODUCT CONTAINS OR PRODUCES A CHEMICAL OR
CHEMICALS WHICH MAY CAUSE SERIOUS ILLNESS OR
DEATH AND WHICH ARE KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM.
4. Make sure the furnace is always connected to an approved vent, in good condition, to carry combustion products outdoors.
5. Familiarize yourself with the controls that shut off the gas
and electrical power to the furnace. If the furnace is to be
shut down at the end of the heating season, turn off both
the gas and electrical power. For safety, always turn the
gas and electrical power off before performing service or
maintenance on the furnace.
WARNING
TO
AVOID POSSIBLE EQUIPMENT DAMAGE, PERSONAL
INJURY, FIRE OR DEATH, THE FOLLOWING INSTRUCTIONS
MUST BE OBSERVED REGARDING UNIT LOCATION, AIR
REQUIREMENTS AND OPERATING PROCEDURES.
6. Establish a regular maintenance schedule to insure efficient and safe operation of the furnace. The furnace
should be checked at the beginning of each heating and
cooling season by a qualified service technician.
WARNING
HEATING
UNIT SHOULD NOT BE UTILIZED WITHOUT
REASONABLE, ROUTINE, INSPECTION, MAINTENANCE AND
SUPERVISION. IF THE BUILDING IN WHICH ANY SUCH DEVICE
IS LOCATED WILL BE VACANT, CARE SHOULD BE TAKEN
THAT SUCH DEVICE IS ROUTINELY INSPECTED, MAINTAINED
AND MONITORED. IN THE EVENT THAT THE BUILDING MAYBE
EXPOSED TO FREEZING TEMPERATURES AND WILL BE
VACANT, ALL WATER-BEARING PIPES SHOULD BE DRAINED,
THE BUILDING SHOULD BE PROPERLY WINTERIZED, AND
THE WATER SOURCE CLOSED. IN THE EVENT THAT THE
BUILDING MAY BE EXPOSED TO FREEZING TEMPERATURES
AND WILL BE VACANT, ANY HYDRONIC COIL UNITS SHOULD
BE DRAINED AS WELL AND, IN SUCH CASE, ALTERNATIVE
HEAT SOURCES SHOULD BE UTILIZED.
WARNING
TO
AVOID PERSONAL INJURY OR FIRE, MINIMUM
CLEARANCES TO COMBUSTIBLE SURFACES MUST BE
FOLLOWED.
7. Make certain the required clearances for the furnace are
always maintained. These clearances are listed on the
furnace clearance label. If any question develops, contact the installer of the furnace or another qualified servicer.
IMPORTANT NOTE TO THE OWNER REGARDING PRODUCT
LIMITED WARRANTY
UNIT INSTALLATION
Your limited warranty certificate is supplied as a separate
document with the unit installed by your contractor. Read
the limited warranty certificate carefully to determine what is
and is not covered and keep the warranty certificate in a
safe place. If you are unable to locate the warranty certificate please contact your installing contractor or contact customer service (877-254-4729) to obtain a copy.
1. All flue product carrying passages external to the furnace
(i.e. chimney, vent connector) are clear and free of obstructions.
Examine the furnace installation to determine the following:
2. The vent connector is in place, slopes upward and is
physically sound without holes or excessive corrosion.
3. The return air duct connection is physically sound, sealed
to the furnace casing, and terminates outside the space
containing the furnace.
Before using this manual, check the serial plate for proper
model identification.
4. The physical support of the furnace is sound without sagging, cracks, or gaps around the base so as to provide a
seal between the support and the base.
The installation and servicing of this equipment must be
performed by qualified, experienced technicians only.
5. There are no obvious signs of deterioration of the furnace.
UNIT LOCATION
6. Check for proper burner flame performance. Flame should
extend directly outward from burners without curling, floating, or lifting off.
1. The furnace area and the vicinity of any other gas appliances must be kept clear and free of combustible materials, gasoline, and other flammable vapors and liquids.
Also, do not store or use flammable items such as paint,
varnish, or lacquer in the area.
3
1. Headaches, Nausea, Dizziness, Flu-like symptoms.
AIR REQUIREMENTS
2. Excessive humidity, heavily frosted windows or a moist
“clammy” feeling in the home.
WARNING
3. Smoke from a fireplace will not draw up the chimney.
TO
AVOID PROPERTY DAMAGE, PERSONAL INJURY OR
DEATH, SUFFICIENT FRESH AIR FOR PROPER COMBUSTION
AND VENTILATION OF FLUE GASES MUST BE SUPPLIED.
MOST HOMES REQUIRE OUTSIDE AIR BE SUPPLIED INTO THE
FURNACE AREA.
4. Flue gases that will not draw up the appliance vent pipe.
COMBUSTION AIR
The air for combustion and ventilation can also (where local
codes permit) be obtained from the surrounding unconfined
space or louvered closet door. Observe the following precautions concerning air availability:
Improved construction and additional insulation in homes
have reduced the heat loss and made these homes much
tighter around doors and windows so that air infiltration is
minimal. This creates a problem to supply ventilation and/or
combustion air for gas fired or other fuel burning appliances.
Any use of appliances that pull air out of the house (clothes
dryers, exhaust fans, fireplaces, water heaters, non-direct
vent furnaces, etc.) could reduce combustion air to the furnace.
• When a furnace is installed in a closet and the closet
door is louvered, DO NOT OBSTRUCT LOUVERS. Louvers must be open and clear to provide combustion air
to the furnace.
• When a furnace is installed in a confined space within a
home and the air for combustion and ventilation enters
the space through ducts from the outside, be sure to
routinely check the entering and outlet, grilled openings
to verify that they are always clear and clean.
If fuel-burning appliances are starved for air, the flue gases
produced may not vent outdoors properly. These flue gases
may include carbon monoxide.
• Do not partition off a small area around the furnace utilizing a non-louvered door. This could obstruct the combustion air from reaching the furnace.
DANGER
INDOOR HUMIDITY
Relative humidity is the amount of water vapor in the air relative to the amount the air can hold at the same temperature.
The colder the air; the less moisture it can hold. As air is
warmed, its ability to hold moisture is increased. Relative
humidity is important to your health and home as proper
humidification helps reduce respiratory difficulties and helps
improve the indoor air quality.
CARBON MONOXIDE POISONING HAZARD
Special warning for installation of furnaces or air handling units in enclosed areas such as garages, utility rooms or parking areas. Carbon monoxide producing
devices (such as automobiles, space heaters, gas water heaters, etc.) should not be operated in enclosed areas such as unventilated garages or utility rooms
because of the danger of carbon monoxide (CO) poisoning resulting from the exhaust emissions. If a furnace or air handler is installed in an enclosed area and a
carbon monoxide producing device is operated therein, there must be adequate direct outside ventilation. Carbon monoxide emissions can be (re)circulated
throughout the structure if the furnace or air handler is operating in any mode. CO can cause serious illness including permanent brain damage or death.
DANGER
RISQUE D'EMPOISONNEMENT AU MONOXYDE DE CARBONE
A good relative humidity is one just high enough to barely
start condensation along the lower edges or lower corners
of the windows. More than that can be damaging.
Avertissement special au sujet de l'installation d'appareils de chauffage ou de traitement d'air dans des endroits clos, tets les garages, les locaux d'entretien et les
Stationnements. Evitez de mettre en marche les appareils produisant du monoxyde de carbone (tels que les automobile, les appareils de chauffage autonome,etc.)
dans des endroits non ventilés tels que les d'empoisonnement au monoxyde de carbone. Si vous devez faire fonctionner ces appareils dans un endroit clos,
assures-vous qu'il y ait une ventilation directe provenant de l'exterier . Les émissions de monoxyde de carbone peuvent etre recircules dans les endroits clos,
si l'appareil de chauffage ou de traitement d'air sont en marche. Le monoxyde de carbone peut causer des maladies graves telles que des dommages permanents
au cerveau et meme la mort.
Frequent fogging or excessive condensation on inside windows indicates the indoor humidity level is too high for outdoor weather conditions. Damage to the building may result
if the condition persists. Condensation on inside of storm
windows indicates a poor seal inside windows. Adding
weather-stripping to tighten inside windows usually corrects
this problem.
PELIGRO
' POR MONÓXIDO DE CARBONO
RIESGO DE INTOXICACIÓN
Advertencia especial para la instalación de calentadores ó manejadoras de aire en áreas cerradas como estacionamientos ó cuartos de servicio. Los equipos ó
aparatos que producen monóxido de carbono (tal como automóvil, calentador de gas, calentador de agua por medio de gas, etc) no deben ser operados en
áreas cerradas debido al riesgo de envenenamiento por monóxido de carbono (CO) que resulta de las emisiones de gases de combustión. Si el equipo ó
aparato se opera en dichas áreas, debe existir una adecuada ventilación directa al exterior. Las emisiones de monóxido de carbono pueden circular a través
del aparato cuando se opera en cualquier modo. El monóxido de carbono puede causar enfermedades severas como daño cerebral permanente ó muerte.
0140M00020-D
The following table shows the recommended maximum indoor humidity in relationship to the outdoor temperatures.
Carbon monoxide or “CO” is a colorless and odorless gas
produced when fuel is not burned completely or when the
flame does not receive sufficient oxygen.
Be aware of these air starvation signals which indicate
conditions that my result in carbon monoxide or that
carbon monoxide may be present:
4
ing functions. The level of this control depends on the type
of thermostat applied.
Outdoor
Humidity
Temperature Single -Paned Double-Paned
Glass
Glass
+30°F
30%
50%
+20°F
20%
40%
+10°F
15%
35%
0°F
10%
30%
-10°F
5%
25%
-20°F
5%
20%
-30°F
3%
18%
Room Temperature
Thermostat
Cool/Heat
Temperature
Control Dials
PROPANE (LP) GAS INSTALLATIONS ONLY
For furnaces operating on propane gas, please review the
following warnings before use.
Cool/Heat
Switch
Fan Switch
WARNING
TO
AVOID PROPERTY DAMAGE, PERSONAL INJURY OR
DEATH, DUE TO EXPLOSION OR FIRE, INSTALL A GAS
DETECTING WARNING DEVICE. SINCE THE ODORANT IN
PROPANE GAS CAN BE REDUCED BY IRON OXIDE (RUST), A
GAS DETECTING WARNING DEVICE IS THE ONLY RELIABLE
METHOD TO DETECT PROPANE GAS LEAKS.
System
Switch
OFF
Fan
Switch
AUTO
COOL
AUTO
COOL
ON
HEAT
AUTO
HEAT
ON
OFF
ON
WARNING
IF
THE GAS FURNACE IS INSTALLED IN A BASEMENT, AN
EXCAVATED AREA OR CONFINED SPACE, IT IS STRONGLY
RECOMMENDED TO CONTACT A PROPANE SUPPLIER TO
INSTALL A GAS DETECTING WARNING DEVICE IN CASE OF A
GAS LEAK.
• SINCE PROPANE GAS IS HEAVIER THAN AIR , ANY LEAKING
GAS CAN SETTLE IN ANY LOW AREAS OR CONFINED
SPACES.
• PROPANE GAS ODORANT MAY FADE, MAKING THE GAS
UNDETECTABLE
Action
None
System only cools, fan
cycles off and on.
System only cools, fan
runs all the time.
System only heats, fan
cycles off and on.
System only heats, fan
runs all the time.
No heating or cooling,
fan runs all the time.
If this furnace is a part of the Goodman ComfortNet™ family
of products, a ComfortNet thermostat may also be used to
control this furnace. This thermostat is a programmable type
that allows the setting of different temperatures during the
night and during the day. It may also be set to automatically
switch from heating to cooling. The fan switch may also be
set to ON or Auto. The ComfortNet™ system also includes
advanced set up and diagnostic features which is explained
in the ComfortNet User Manual provided with the control.
WARNING
AN
UNDETECTED GAS LEAK WILL CREATE A DANGER OF
EXPLOSION OR FIRE. IF THE PRESENCE OF GAS IS
SUSPECTED, FOLLOW THE INSTRUCTIONS ON THE COVER
OF THIS MANUAL. FAILURE TO DO SO COULD RESULT IN
FURNACE OPERATION
SERIOUS PERSONAL INJURY OR DEATH.
WARNING
THERMOSTAT FUNCTIONS
ELECTRICAL
COMPONENTS ARE CONTAINED IN BOTH
COMPARTMENTS. TO AVOID PERSONAL INJURY,
ELECTRICAL SHOCK OR DEATH, DO NOT REMOVE ANY
INTERNAL COMPARTMENT COVERS. CONTACT A QUALIFIED
SERVICER AT ONCE IF AN ABNORMAL CONDITION IS
NOTICED.
There are many types and styles of thermostats but operation is usually similar. BE SURE TO BECOME FAMILIAR
WITH YOUR THERMOSTAT. The simplest type of thermostat only starts and stops the furnace to maintain the desired room temperature. The most widely used types will
control both heating and cooling functions and will have a
Fan Switch with Auto and ON settings. On Auto, the circulating air blower will cycle on/off with the furnace but if switched
to ON it will run continuously regardless of whether or not
heating or cooling is being provided.
Keep both doors in place except for inspection and maintenance. An interlock switch prevents furnace operation if the
blower door is not in place.
FURNACE START-UP
1. Close the external manual gas shut-off valve.
In addition, there are thermostats which automatically switch
from heating to cooling mode and those with night set back
capability. The night set back, or multiple set back, type
allows for a different temperature at night or during the day
when no one is at home. Programmable thermostats will
allow for more control and tailoring of the heating and cool-
2. Turn off the electrical power to the furnace.
3. Set the room thermostat to the lowest possible setting.
4. Remove the burner compartment door.
5
5. This furnace is equipped with an ignition device which
automatically lights the burner. Do not try to light the
burner by hand.
6. Move the furnace’s gas valve ON/OFF switch to the OFF
position.
7. Wait five minutes to clear out any gas. Then smell for
gas, including near the floor as some types of gas are
heavier than air.
8. If you smell gas following the five minute waiting period
in step 7, immediately follow the instructions on the cover
of this manual. If you do not smell gas after five minutes,
move the furnace’s gas valve ON/OFF switch to the ON
position.
White-Rodgers Model 36G22/36J22 (Single-Stage)
9. Replace the burner compartment door.
10. Open the external manual gas shut-off valve.
11. Turn on the electrical power to the furnace.
12. Adjust the thermostat to a setting above room temperature.
White-Rodgers Model 36G54/36J54 (Two-Stage)
13. After the burners are lit, set the thermostat to desired
temperature.
FURNACE SHUT DOWN
To shut down your furnace, follow the steps listed below.
1. Set the thermostat to the lowest setting.
2. Integrated control closes gas valve extinguishing flame.
3. Induced draft blower is de-energized following a 15 second delay. The circulator blower is de-energized following a 90, 120, 150, or 180 second delay period.
4. Remove the burner compartment door.
Gas Valve On/Off
Selector Switch
5. Move the furnace’s gas valve ON/OFF switch to the OFF
position.
Honeywell Model VR8215 (Single-Stage)
6. Close the external manual gas shut-off valve.
7. Replace the burner compartment door.
LOCKOUT RESET
Furnace lockout is characterized by a non-functioning furnace (circulator blower may be running continuously) providing a diagnostic LED code. Lockout results when a furnace control detects abnormal conditions. If the furnace is
in “lockout”, it may be reset by any of the following methods:
Gas Valve On/Off
Selector Switch
Honeywell Model VR9205 (Two-Stage)
1. One hour automatic reset. Control will automatically reset itself and attempt to resume normal operations following a one hour lockout period.
INLET
2. Power interruption. Interrupt 115 volt power to the furnace for greater than 20 seconds.
OUTLET
3. Thermostat cycle. Interrupt thermostat signal to the furnace for between 0 and 20 seconds.
Gas Valve On/Off
Selector Switch
If the condition which originally caused the lockout still exists, the control will return to lockout. If your furnace frequently locks out, a problem exists which must be corrected.
Contact a qualified servicer.
Honeywell Model VR9205R (Modulating Gas Valve)
6
ROUTINE MAINTENANCE
• Drainage system. Check for blockage and/or leakage.
Check hose connections at and internal to furnace.
Maintenance is to be performed by a qualified service technician only. User maintenance is to be restricted to frequent
air filter changes and to ensure the warnings and notices
found elsewhere in this manual be followed. We recommend that at a minimum system maintenance be performed
by a qualified service technician prior to the beginning of
each heating season, and if equipped with air conditioning,
prior to air conditioning season.
• Filters. Check that filters are clean and in the proper
placement in the furnace or duct system.
MOTORS
The combustion air motor and indoor blower motor are permanently lubricated and require no further lubrication.
FILTERS
WARNING
WARNING
PERSONAL INJURY
OR DEATH MAY RESULT FROM
IMPROPER MAINTENANCE PERFORMED BY UNTRAINED
PERSONNEL. CALL YOUR INSTALLING DEALER OR OTHER
QUALIFIED SERVICE COMPANIES TO PERFORM THE
MAINTENANCE INSPECTION.
TO
AVOID PROPERTY DAMAGE, PERSONAL INJURY OR
DEATH, DISCONNECT ELECTRICAL POWER BEFORE
REMOVING FILTERS OR PERFORMING ANY OTHER
MAINTENANCE. NEVER OPERATE FURNACE WITHOUT A
FILTER INSTALLED BECAUSE DUST AND LINT WILL BUILD UP
ON INTERNAL PARTS RESULTING IN LOSS OF EFFICIENCY,
EQUIPMENT DAMAGE OR POSSIBLE FIRE.
WARNING
TO
PREVENT PERSONAL INJURY OR DEATH DUE TO
ELECTRIC SHOCK , DISCONNECT ELECTRICAL POWER
BEFORE SERVICING THIS UNIT.
A return air filter is not supplied with this furnace and cannot
be installed inside the cabinet; however, a means of filtering
all of the return air (intake) must be provided. Your installer
will supply filters at the time of installation. Become familiar
with filter location and procedures for removing, cleaning and
replacing them.
ANNUAL INSPECTION
The furnace should be inspected by a qualified installer, or
service agency at least once per year. This check should be
performed at the beginning of the heating season by a qualified technician. This will insure that all furnace components
are in proper working order and that the heating system functions appropriately. Particular attention should be paid to
the following items. Repair or service as necessary.
If you need assistance, contact the installer of your furnace
or another qualified servicer.
Filters must be inspected, cleaned or changed every two
months or as required. As a homeowner, it is your personal
responsibility to keep air filters clean. Remember that dirty
filters are the most common cause of inadequate heating or
cooling performance.
FILTER REMOVAL
Depending on the installation, differing filter arrangements
can be applied. Filters can be located in a central return
grille or a side panel external filter rack (upflow only). To
remove filters from an external filter rack, follow the directions provided with external filter rack kit
Check the
Burner Flames for:
1. Stable, soft and blue.
2. Not curling, floating
or lifting off.
• Flue pipe system. Check for blockage and/or leakage.
Check the outside termination and the connections at
and internal to the furnace.
Horizontal Unit Filter Removal
Filters in horizontal installations are located in the central
return register or the ductwork near the furnace.
• Combustion air intake pipe system (where applicable).
Check for blockage and/or leakage. Check the outside
termination and the connection at the furnace.
To remove:
• Heat exchanger. Check for corrosion and/or buildup
within the heat exchanger passageways.
1. Turn OFF electrical power to furnace.
• Burners. Check for proper ignition, burner flame, and
flame sense. Flames should extend directly outward
from burners without curling, floating or lifting off.
2. Remove filter(s) from the central return register or
ductwork.
• Wiring. Check electrical connections for tightness and/
or corrosion. Check wires for damage.
4. Turn ON electrical power to furnace.
3. Replace filter(s) by reversing the procedure for removal.
7
To remove all other filter configurations, consult with the installing contractor.
• Check thermostat for proper operation. Verify that it is
set on HEAT and that temperature (above room temperature) setting is appropriate.
MEDIA AIR FILTER OR ELECTRONIC AIR CLEANER REMOVAL
• Check the electrical panel for tripped circuit breakers or
failed fuses. Reset the circuit breakers or replace fuses
as necessary.
High efficiency filters are available in both electronic and nonelectronic types. These filters can do a better job of catching small airborne particles. Contact your dealer for further
information.
• Check to see that the manual gas shut-off valve external to the furnace is in the ON position. If the valve is in
the OFF position, turn the gas ON following the start up
procedures outlined in the “Furnace Start-up” section.
If using a Media or Electronic Air Cleaner, follow the directions provided with the air cleaner for proper filter removal,
cleaning, and replacement.
• Check for dirty filter(s). This in the most common cause
of improper furnace operation. Check your filter(s) at
least once a month and replace or clean filters as necessary.
FILTER CLEANING AND/OR REPLACEMENT
• Check for blocked return air or supply air grilles throughout your home. Grilles may be blocked by furniture, drapery, clothes, carpeting, etc. Clear any blockage.
Disposable filters must be replaced with a filter or filters of
the same size as that which is removed. Filters must comply with UL900 or CAN/ULC-S111 Standards.
• Check intake and vent terminations on high efficiency
furnaces to make sure they are not blocked.
Permanent filters must be cleaned, washed, and dried as
specified by the filter manufacturer. If it becomes necessary
to replace a permanent filter, it must be replaced with a filter
or filters of the same size as that which is removed. Filters
must comply with UL900 or CAN/ULC-S111 Standards.
• If your furnace is part of a ComfortNet™ system, check
the ComfortNet thermostat for diagnostic alerts or messages. If the system detects a serious fault in either the
furnace or outdoor unit, the thermostat will display a
“CALL FOR SERVICE” message and scroll the message
“CHECK FURNACE”. The thermostat may also scroll
“CHECK AIR CONDITIONER” or “CHECK HEAT PUMP”
if a serious fault is detected in the outdoor unit (message depends on type of outdoor unit.).
When reinstalling filters, be careful to maintain correct airflow direction.
TROUBLESHOOTING / BEFORE YOU REQUEST A SERVICE CALL
If your furnace is not operating or is performing improperly,
take time to perform the following checks before requesting
service. A couple of simple checks may allow you to avoid a
service call. If the following steps do not resolve the problem, contact a qualified servicer for further troubleshooting
and/or repairs. Do not attempt troubleshooting beyond that
which is outlined in the following bullet points. Do not attempt repairs yourself.
• Check the blower compartment sight glass. If LED is
flashing, record the number of flashes seen in sequence,
shutdown your unit as outlined in the “Furnace Start-up”
section and contact a qualified servicer for further troubleshooting and/or repairs. Refer to Installation Instructions
for code identification. If not flashing, continue with
checks.
8
SAFETY LABELS
NOTE: If safety labels are missing or illegible, contact the installing dealer or our Customer Service Department for ordering
information.
MANUAL GAS
LEVER SHOW N
IN "ON" POS
MANUAL GAS
LEVER SH OW N
I N "ON" POS
G AS
INLET
GAS
INLET
ARRI VEE
D U GAZ
ARRIVEE
DU G AZ
ROBINET A GAZ
MANUEL, EN POS
"ON/MARCHE"
RO BINET A GAZ
MANUEL, EN POS
"O N/MAR CHE"
GAS
INLET
GAS
INLET
ARRIVEE
DU GAZ
ARRIVEE
DU GAZ
MANU AL GAS
LEVER SHOW N
IN "O N" POS
MANUAL G AS
LEVER SHOWN
IN "ON" POS
9
SAFETY LABELS
WARNING
RISK OF ELECTRIC SHOCK. CAN CAUSE INJURY OR DEATH:
DISCONNECT ALL REMOTE ELECTRIC POWER SUPPLIES
BEFORE SERVICING. THIS COMPARTMENT MUST BE CLOSED
EXCEPT WHEN SERVICING.
AVERTISSEMENT
DANGER DE CHOC ELETRIQUE OU DE MORT. COUPEZ TOUT LE
COURANT AVANT TOUT ENTRETIEN OU REPARATION. LE
COMPARTEMENT DOIT RESTER FERMER SAUF PENDANT
LENTRETIEN.
ADVERTENCIA
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION
SERVICE OR MAINTENANCE CAN CAUSE PROPERTY
DAMAGE, PERSONAL INJURY OR DEATH, OR EXPOSURE TO
SUBSTANCES IN FUEL OR FROM FUEL COMBUSTION WHICH
CAN CAUSE DEATH OR SERIOUS ILLNESS, AND WHICH ARE
KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM. READ
AND FOLLOW INSTRUCTIONS AND PRECAUTIONS IN USER'S
INFORMATION MANUAL PROVIDED WITH THIS FURNACE.
INSTALLATION AND SERVICE MUST BE PERFORMED BY A
QUALIFIED INSTALLER, SERVICE AGENCY OR GAS
SUPPLIER.
PELIGRO DE CHOQUE ELECTRICO O MUERTE. DESCONECTE
TODAS LAS FUENTES DE ENERGIA ELECTRICA ANTES DE
MANTENIMIENTO O SERCICO TECNICO. EL COMPARTIMIENTO
DEBE PERMANCECER CERRADO EXCEPTO DURANTE EL
SERVICIO DE MANTENIMIENTO.
WARNING
HEATING UNITS SHOULD NOT BE UTILIZED WITHOUT REASONABLE ROUTINE
INSPECTION, MAINTENANCE, AND SUPERVISION. IF THE BUILDING IN WHICH ANY
SUCH DEVICE IS LOCATED WILL BE VACANT, CARE SHOULD BE TAKEN THAT SUCH
DEVICE IS ROUTINELY INSPECTED, MAINTAINED, AND MONITORED. IN THE EVENT
THAT THE BUILING IS EXPOSED TO FREEZING TEMPERATURES, ALL WATER-BEARING
PIPES SHOULD BE DRAINED, THE BUILDING SHOULD BE PROPERLY WINTERIZED, AND
THE WATER SOURCE CLOSED. SHOULD THE BUILDING BE EXPOSED TO FREEZING
TEMPERATURES, ANY HYDRONIC COIL UNITS SHOULD BE DRAINED AS WELL; AND, IN
SUCH CASE, ALTERNATIVE HEAT SOURCES SHOULD BE UTILIZED.
AVERTISSEMENT
UNITES DE CHAUFFAGE NE DEVRAIT ETRE UTILISE SANS RAISONNABLE INSPECTION
DE ROUTINE, LA MAINTENANCE ET LA SUPERVISION, SI L'IMMEUBLE DANS LEQUEL
UN TEL DISPOSITIF SE TROUVE SERA VACANTE, IL CONVIENT DE VEILLER A CE QUE
CE TYPE D'APPAREIL EST REGULIEREMENT INSPECTE ET ENTRETENU, ET SURVEILLES.
DANS LE CAS OU L'IMMEUBLE EST EXPOSEE A DES TEMPERATURES DE GEL, TOUTE
L'EAU DES TUYAUX DE ROULEMENT DOIT ETRE VIDANGEE, LE BATIMENT DEVRAIT
ETRE CORRECTEMENT URBANO, ET LA SOURCE D'EAU FERME. SI LE BATIMENT EST
EXPOSE A DES TEMPERATURES DE GEL, AUCUNE BOBINE HYDRONIQUE UNITES DOIT
ETRE VIDANGE AINSI; ET, DANS DE TELS CAS, D'AUTRES SOURCES DE CHALEUR
DEVRAIT ETRE UTILISE.
WARNING
FIRE, EXPLOSION, AND ASPHYXIATION HAZARD
IMPROPER ADJUSTMENT, ALTERATION, SERVICE, MAINTENANCE OR INSTALLATION
CAN CAUSE SERIOUS INJURY OR DEATH.
READ AND FOLLOW INSTRUCTIONS AND PRECAUTIONS IN USER'S INFORMATION
MANUAL PROVIDED WITH THIS FURNACE. INSTALLATION AND SERVICE MUST BE
PERFORMED BY A QUALIFIED SERVICE AGENCY OR GAS SUPPLIER.
UN REGLAGE, UNE MODIFICATION, UN RÉPARATION, UN
ENRETIEN OU UNE INSTALLATION INCORRECT PUET
ENTRAÎNER DES BLESSURES GRAVES OU LA MORT.
SUIVRE LES INSTRUCTION ET LES CONSIGNES QUI
FIGURENT DANS LA NOTICE D'UTILISATION QUI
ACCOMPAGNE CE GÉNÉRATEUR D'AIR CHAUD.
L'INSTALLATION ET L'ENTRETIEN DOIVENT ÊTRE
EFFECTURÉS PAR UN RÉPARATEUR QUALIFIÉ OU PAR LE
FOURNISSEUR DE GAZ.
CAN RESULT IN SERIOUS INJURY OR DEATH.
DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS AND LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.
STORAGE OF OR USE OF GASOLINE OR
OTHER FLAMMABLE VAPORS OR LIQUIDS IN
THE VICINITY OF THIS OR ANY APPLIANCE
CAN RESULT IN SERIOUS INJURY OR DEATH.
RISQUE DE BLESSURES GRAVES OU DE
MORT. NE PAS ENTREPOSER NI UTILISER DE
L'ESSENCE NI D'AUTRES VAPEURS OU
LIQUIDES INFLAMMABLES DANS LE
VOISINAGE DE CET APPAREIL, NI DE TOUT
AUTRE APPAREIL. LE FAIT D'ENTREPOSER OU
D'UTILISER DE L'ESSENCE OU D'AUTRES
LIQUIDES OU VAPEURS INFLAMMABLES À
PROXIMITÉ DE CET APPAREIL OU DE TOUT
AUTRE APPAREIL PEUT CAUSER DES
BLESSURES GRAVES OU LA MORT.
SEE INSIDE SURFACE OF BURNER
COMPARTMENT DOOR FOR
LIGHTING/OPERATING INSTRUCTIONS.
FILTER(S) SHOULD BE INSPECTED FREQUENTLY AND CLEANED
WHEN NECESSARY. WHEN REPLACEMENT IS REQUIRED BE
SURE TO USE THE SAME TYPE (CLASS 1 OR 2) AND SIZE
ORIGINALLY INSTALLED AND THAT IT IS U.L.C.* CERTIFIED.
*CANADIAN REQUIREMENT
LES INDICATIONS POUR L 'ECLAIRAGE ET
LE SERVICE SE TROUVENT A LA
SURFACE INTERIEURE LA PORTE DU
COMPARTIMENT DU BRULEUR.
LES FILTRES DOIVENT ETRE FREQUEMMENT INSPECTES ET
NETTOYES SI NECESSAIRE. REMPLACES-LES DE FILTRES DU
MEME TYPE (CLASSE 1 OU 2) ET FORMAT QUE DANS
L'EQUIPEMENT ORIGINAL. CERTIFIES PAR LE U.L.C.
AVERTISSEMENT
RISQUE D'INCENDIE ET D'ASPHYXIE
UN REGLAGE, UNE MODIFICATION, UNE REPARATION, UN ENTRETIEN OU UNE
INSTALLATION INCORRECTE PEUT ENTRAINER DES BLESSURES GRAVES OU LA
MORT. SUIVEZ LES INSTRUCTION ET LES CONSIGNES DANS LA NOTICE
D'UTILISATION QUI ACCOMPAGNE CE GENERATEUR D'AIR CHAUD. L'INSTALLATION
ET L'ENTRETIEN DOIVENT ETRE EFFECTUES PAR UN REPARATEUR QUALIFIE OU PAR
LE FOURNISSEUR DE GAZ
0140M00409
DANGER
CARBON MONOXIDE POISONING HAZARD
Special warning for installation of furnaces or air handling units in enclosed areas such as garages, utility rooms or parking areas. Carbon monoxide producing
devices (such as automobiles, space heaters, gas water heaters, etc.) should not be operated in enclosed areas such as unventilated garages or utility rooms
because of the danger of carbon monoxide (CO) poisoning resulting from the exhaust emissions. If a furnace or air handler is installed in an enclosed area and a
carbon monoxide producing device is operated therein, there must be adequate direct outside ventilation. Carbon monoxide emissions can be (re)circulated
throughout the structure if the furnace or air handler is operating in any mode. CO can cause serious illness including permanent brain damage or death.
DANGER
RISQUE D'EMPOISONNEMENT AU MONOXYDE DE CARBONE
Avertissement special au sujet de l'installation d'appareils de chauffage ou de traitement d'air dans des endroits clos, tets les garages, les locaux d'entretien et les
Stationnements. Evitez de mettre en marche les appareils produisant du monoxyde de carbone (tels que les automobile, les appareils de chauffage autonome,etc.)
dans des endroits non ventilés tels que les d'empoisonnement au monoxyde de carbone. Si vous devez faire fonctionner ces appareils dans un endroit clos,
assures-vous qu'il y ait une ventilation directe provenant de l'exterier . Les émissions de monoxyde de carbone peuvent etre recircules dans les endroits clos,
si l'appareil de chauffage ou de traitement d'air sont en marche. Le monoxyde de carbone peut causer des maladies graves telles que des dommages permanents
au cerveau et meme la mort.
PELIGRO
' POR MONÓXIDO DE CARBONO
RIESGO DE INTOXICACIÓN
Advertencia especial para la instalación de calentadores ó manejadoras de aire en áreas cerradas como estacionamientos ó cuartos de servicio. Los equipos ó
aparatos que producen monóxido de carbono (tal como automóvil, calentador de gas, calentador de agua por medio de gas, etc) no deben ser operados en
áreas cerradas debido al riesgo de envenenamiento por monóxido de carbono (CO) que resulta de las emisiones de gases de combustión. Si el equipo ó
aparato se opera en dichas áreas, debe existir una adecuada ventilación directa al exterior. Las emisiones de monóxido de carbono pueden circular a través
del aparato cuando se opera en cualquier modo. El monóxido de carbono puede causar enfermedades severas como daño cerebral permanente ó muerte.
0140M00020-D
10
22317001
THIS PAGE INTENTIONALLY LEFT BLANK
11
Most questions can be answered by your local dealer. For additional information, please call:
CONSUMER INFORMATION LINE
TOLL FREE
1-877-254-4729 (U.S. only)
email us at: customerservice@goodmanmfg.com
fax us at: (731) 856-1821
(Not a technical assistance line for dealers.)
Outside the U.S., call 1-713-861-2500.
(Not a technical assistance line for dealers.)
Your telephone company will bill you for the call.
To obtain the proper labels, the Model Number and Serial Number of the unit must be
supplied. These numbers are recorded on the nameplate of the furnace. For convenience, record this information here:
MODEL NUMBER: _ _ _ _ _ _ _ _ _ _ _ _ _
Goodman Manufacturing Company, L.P.
5151 San Felipe, Suite 500, Houston, TX 77056
www.goodmanmfg.com • www.amana-hac.com
is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
12
Download PDF