User Bulletin ABI PRISM

User Bulletin ABI PRISM
User Bulletin
ABI PRISM ® 377 DNA Sequencer
December 10, 1999
SUBJECT: New Data Collection and Sequence Analysis Software Installation
Guidelines and Fifth-Dye Sequencing
Overview This bulletin describes the changes in the new versions of the ABI PRISM ® 377 Data
Collection Software and ABI PRISM ® DNA Sequencing Analysis Software for the
ABI PRISM ® 377 DNA Sequencer and gives the procedures to use the new data
collection software with the ABI PRISM ® Lane Guide™ Lane Identification reagents.
In This Bulletin This user bulletin covers the following topics:
Topic
See Page
Safety
2
Product Overview
3
Key Features of the Software Upgrades
4
Obtaining the New Products
6
Installing and Setting Up the New Software
7
Testing the Long Pass Filter
16
Loading the Gel
18
Using the Data Collection Software
19
Technical Support
23
Safety
Documentation User Five user attention words appear in the text of all PE Biosystems user documentation.
Attention Words Each word implies a particular level of observation or action as follows.
Note
This word is used to call attention to information.
IMPORTANT This word calls attention to information that is necessary for correct operation of
the kit or instrument.
CAUTION This word informs the user that damage to the instrument could occur if the
user does not comply with the information. It also indicates a potentially hazardous
situation that could result in minor or moderate injury to the user.
! WA RNING ! This word informs the user that serious physical injury or illness to
the user or other persons could occur if these required precautions are not taken.
! DAN G ER ! Indicates an imminently hazardous situation that, if not avoided, will
result in death or serious injury.
General Warning ! WA RNING ! CHEMICAL HAZARD. Some chemicals used with PE Biosystems
instruments or kits may be hazardous and can cause injury, illness, or death. Check
regularly for chemical leaks and chemical spills, which represent potential safety
hazards to the operator. If a leak or a spill occurs, follow clean-up instructions in the
Material Safety Data Sheets (MSDSs), or in the Waste Profile in the Site Preparation and
Safety Guide. Hazardous Chemical Warnings are prominently displayed on the labels of
all hazardous materials. Always read the appropriate MSDSs and Waste Profiles before
using the chemicals in any way.
User Safety Always wear the appropriate protective gloves, clothing, and eyewear when handling
Precautions chemicals.
Ordering MSDSs Material Safety Data Sheets (MSDSs) for hazardous chemicals manufactured by
PE Biosystems will accompany your first shipment. To receive additional copies of
MSDSs at no extra cost, call PE Biosystems at (800) 327-3002.
For chemicals required for this instrument but not manufactured or sold by
PE Biosystems, please obtain the MSDSs from their manufacturers.
Ordering Kits and To order ABI PRISM kits or reagents, please contact PE Biosystems at one of the
Reagents regional sales offices listed in the Technical Support section of this user bulletin.
Please have the part number of the kit or reagent you are ordering available when
ordering.
Page 2 of 26
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Product Overview
About Lane Guide The Lane Guide reagents add fifth dye labeled bands to the lanes in which they are
Reagents loaded, greatly improving lane identification, even under conditions of multiple
adjacent sample failures or migration anomalies.
Using Lane Guide reagents in gels run on the ABI PRISM 377 DNA Sequencer helps
you identify each sample in a gel.
Only sequencing analysis software currently supports the use Lane Guide reagents.
ABI PRISM ® 377 GeneScan Analysis Software does not support the use of Lane
Guide reagents at this time.
About the Software There are occasions when a gel includes so many failed reactions that it is impossible
to be certain of sample identities. The Lane Guide reagents combined with data
collection and sequencing analysis software provide an integrated solution to this
serious problem.
Instrument software has been upgraded to provide fifth dye virtual filter capability to all
ABI PRISM 377 instruments except the 377-18 instrument. The Lane Guide™ Neural
Net Tracker has been upgraded so that it can use the bands produced by the Lane
Guide reagents for improved lane detection, assignment, and tracking.
Instrument software has also been upgraded with new features and improvements.
Benefits The combination of Lane Guide reagents and the firmware, data collection, and
sequencing analysis software upgrades provides users:
Cost savings in reagents
Cost savings in labor
Time savings in troubleshooting
Time savings in retracking
A high degree of confidence in lane assignments
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 3 of 26
Key Features of the Software Upgrades
Introduction Data collection software has been upgraded to enhance the capabilities of the 377
base model, XL, and 96-Lane instruments with a fifth virtual filter capability. In
addition, a number of other new features have been added.
Sequencing analysis software has also been upgraded with a new tracker that makes
use of the fifth dye.
Data Collection The table below lists and describes the new software features.
Version 2.6
Page 4 of 26
Feature
Description
Sequencing support for a
fifth dye
Sample sheets and run sheets can now support five dyes.
Sample sheets are configured as either 4- or 5-dye sample
sheets.
Dynamic link between
sample sheet and run sheet
Sample sheets and run sheets are now linked when the
sample sheet is chosen from within the run sheet. Any
samples that are added and saved to the sample sheet are
automatically updated on the run sheet. Once a run is
complete, the run sheet is unlinked, preserving the history of
run sheets from completed runs.
Applescript ® support
This application now supports an Apple event that lets you
import a text file. The information from the text file is used to
fill out a sample sheet and, optionally, a run sheet based on
the imported sample sheet.
New module files
New 5-dye sequencing analysis E module files have been
added. GeneScan E module files have been added,
supporting the dRhodamine SNaPshot™ protocol. When a
Sequencing run sheet is based on a 5-dye sample sheet,
only 5-dye module files are available for selection.
Error log
Any data that is incorrect and cannot be corrected is noted in
the error log. The error log can now display up to 1 MB of
text.
No changes to instrument
files
There is no need to make a new instrument file when using
Lane Guide reagents.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Sequencing Analysis The table below lists and describes the new software features.
Software Version 3.4
Feature
Description
Lane Guide Neural Net
Tracker
The tracker has been upgraded to use the bands produced
by Lane Guide reagents in lane identification and in the
development of confidence values.
ABI PRISM® BioLIMS
Genetic Information
Management System
compatibility
Sequencing analysis software is now compatible with
BioLIMS v. 2.0.1.
ABI PRISM ® Factura Feature
Identification Software
update
Factura software is updated to v. 2.2.2. The new Factura
software is also compatible with BioLIMS v. 2.0.1.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 5 of 26
Obtaining the New Products
System Requirements Macintosh ® PowerPC processor
Mac OS 7.6.1 and later
–
For all instruments, no change is required to the existing Mac OS
32 MB RAM minimum, 64 MB RAM recommended
Hardware A small number of instruments have a long pass filter that does not work with the
Requirements bands produced by Lane Guide reagents. Please see “Testing the Long Pass Filter”
on page 16 for the procedure to test your instrument.
How to Download Software updates for data collection and sequencing analysis software can be
downloaded from the PE Biosystems web site:
http://www.pebio.com/ab/techsupp/swpps/377sw.html
How to Order The following software and Lane Guide kits can be ordered from your PE Biosystems
representative (please see “Ordering Kits and Reagents” on page 2):
Page 6 of 26
Item
Requirement
Part Number
ABI PRISM Data Collection
Software, Version 2.6-01 update
Any earlier version of data
collection software
4313657
ABI PRISM Data Collection
Software, Version 2.6-XL update
Any earlier version of XL data
collection software
4313658
ABI PRISM Data Collection
Software, Version 2.6-96 update
Any earlier version of 96-lane data
collection software
4313659
ABI PRISM Sequencing Analysis
Software, Version 3.4 upgrade
Sequencing analysis software
earlier than Version 3.0
4313075
ABI PRISM Sequencing Analysis
Software, Version 3.4 update
Sequencing analysis software
Version 3.0 or higher
4313076
Lane Guide 200 Reaction Kit
200 reactions
4313682
Lane Guide 1000 Reaction Kit
1000 reactions
4313677
Lane Guide 5000 Reaction Kit
5000 reactions
4313679
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Installing and Setting Up the New Software
Before Starting the Before installing the new software, you must remove the preferences file of the old
Installation software to prevent any conflicts. You also need to record the CCD pixel position.
To obtain the CCD pixel position value:
Step
Action
1
Open the data collection software.
2
Under Window in the main menu, select Manual Control.
The Manual Control window opens:
3
Using the Fxn Name pull-down menu, select CCD Pixel Position:
4
Record the number that appears in the Value box:
5
Close the Manual Control window and quit the data collection software.
To remove the preferences file:
Step
Action
1
Open the System Folder on your Macintosh hard drive.
2
Find and open the Preferences folder.
3
Find and throw away the appropriate data collection preferences file for your
instrument:
ABI 377
ABI 377XL
or
ABI 377-96
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 7 of 26
To remove the preferences file: (continued)
Step
4
Action
Verify the ABI 377 calibrations file exists.
Do not throw away the calibrations file.
IMPORTANT If the calibrations file does not exist, you must make one. Please
refer to the ABI PRISM DNA Sequencing Analysis Software User’s Manual (P/N
4306158) for the procedure for making a calibrations file.
5
Close your Macintosh hard drive folder.
How to Install Both data collection updates and upgrades can be installed using the same
procedure.
Note To install the new ABI PRISM Sequencing Analysis Software, please refer to the
ABI PRISM DNA Sequencing Analysis Software User’s Manual.
To install the new firmware and data collection software:
Step
Action
1
Download the desired new software from the web site, or
insert the CD into the CD-ROM drive.
2
Find and double-click the installer icon:
The main installer window opens.
3
Click the Continue button.
A window with installation instructions and other important information opens.
Page 8 of 26
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
To install the new firmware and data collection software: (continued)
Step
4
Action
You can read the installation instructions by scrolling through the text with the scroll
bar on the right of the window. You can also print or save the contents.
When you are ready to proceed with the installation, click the Continue button.
The Collection Installer window opens.
5
The default installation location is the local hard disk.
If you wish to specify a different location, use the pop-up menu at the bottom of the
window:
6
When ready, click the Install button.
A window appears showing the progress of the installation. When complete, the
final installation window appears.
7
Click the Quit button to exit the Installer.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 9 of 26
Minimize the Loading and updating preferences and opening run sheets now takes significantly
Number of Module longer than with earlier versions of the data collection software.
Files Each time the collection software opens the preferences or run sheet window, it must
sort through the 4- and 5-dye modules in the module folder before opening the
window. You can reduce the time it takes for the collection software to open these
windows by minimizing the number of module files in the module folder.
To minimize the number of module files:
Step
Action
1
Locate and open the ABI PRISM 377 (377XL or 377-96) folder.
2
Open the Modules folder.
3
Identify and select all module files which you will not be using regularly.
4
Move the selected module files to the Unused Modules folder.
Set Preferences The procedure for setting the preferences differs from that for earlier versions of the
collection software.
IMPORTANT Loading and updating the new preferences now takes significantly longer than
with earlier data collection software versions. Please see “Minimize the Number of Module
Files” on page 8 for the procedure to reduce this time.
To set the preferences:
Step
1
Page 10 of 26
Action
Open the data collection software.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
To set the preferences: (continued)
Step
2
Action
The data collection software requires that all the preferences be set when it is first
opened.
Using the following example and the table below, select the appropriate folder for
each prompt as follows.
Prompt
Selections
Foldera
Action
Sample Sheets
Highlight the Sample Sheets folder and click the Select
“Sample Sheets” button.
Modules
Highlight the Modules folder and click the Select “Modules”
button.
Runs
Highlight the Run folder and click the Select “Runs” button, or
locate a folder in which you want the data to be stored and
select that folder.
Firmware
Image
Highlight the Firmware Image folder and click the Select
“Firmware Image” button.
Settings
The data collection software automatically sets to the ABI
Prism folder inside the System folder.
GeneScan
Parameterb
Locate and open the ABI Prism GeneScan folder, highlight
the GS Parameters folder, and click the Select “GS
Parameters Folder” button.
GeneScan
Standardsb
Locate and open the ABI Prism GeneScan folder, highlight
the GS Standards folder, and click the Select GS Standards
Folder button.
a. The folder name varies depending on the version of data collection software used.
b. If the GeneScan software is not installed on the computer, go to step 3.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 11 of 26
To set the preferences: (continued)
Step
3
Action
If you have not installed the GeneScan software, select the ABI Folder or Chiller
Modules folder for the two GeneScan preferences requested as shown below.
Note You must define a folder location for the GeneScan preferences file even if
the GeneScan software is not installed on the Macintosh. If a folder location is not
selected, the preceding dialog box will appear every time the data collection
software is opened.
4
From the Window menu select Preferences, then select File Names.
a. Enter the desired file or folder name in the appropriate field.
b. Open the associated pull-down menu to specify the date and time (<date>), or
nothing (<none>) as a suffix.
Page 12 of 26
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
To set the preferences: (continued)
Step
5
Action
From the Page menu select Sequence Sample Sheet Defaults.
a. Open the DyeSet/Primer or Instrument File pull-down menu.
b. Select the desired file from the pull-down menu.
6
From the Page menu select Sequence Run Defaults.
Change the default setting for the WTR distance, 4- and 5-dye prerun and run
modules, and the number of lanes:
a. Open the pull-down menu for each parameter.
b. Select the desired default setting.
7
To specify that data be automatically analyzed by the sequencing analysis software:
a. Select the Autoanalyze with check box.
b. Open the Autoanalyze with pull-down menu and select Other.
c. Locate and double-click the analysis application you want to use.
8
To specify that data be printed automatically at the end of each run, select the Auto
Print check box.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 13 of 26
To set the preferences: (continued)
Step
9
Action
From the Page menu select General Settings.
a. Type in the instrument name or serial number.
b. From the 4Dye Plate Check Module and 5Dye Plate Check Module pull-down
menus, select the desired module.
Note You will also have to reset preferences for both GeneScan and BioLIMS
software, if you use these applications. Please see “Setting Preferences” on pages
5-1 to 5-20 in the ABI PRISM 377 DNA Sequencer User’s Manual (P/N 4307164).
10
Click OK when finished.
Download the If you have a version of firmware earlier than v. 2.5, you will be prompted to download
Firmware the new firmware to the 377 instrument. This requires a total reset.
To perform a total reset:
Step
1
Action
Using the eraser end of a pencil or similar object, press the red reset button on the
back of the instrument twice in rapid succession.
Note To be sure the old firmware has been removed, check the front panel lights.
You should see the yellow light blinking.
2
Open the data collection software.
The firmware is automatically downloaded to the instrument. This will take
60–90 seconds.
For information on troubleshooting firmware, please refer to “About Troubleshooting
Firmware” on page 4-21 in the ABI PRISM 377 DNA Sequencer User’s Manual.
Page 14 of 26
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Sending CCD Pixel
Position and
Instrument Serial
Number
The CCD pixel position and instrument serial number must be sent to the 377
instrument after loading v. 2.5 of the firmware.
Note The following procedure requires a valid calibration file. To update or create one, please
refer to “CCD Pixel Position Value” on page 4-25 and “Using Calibration File Make and Send” on
page 4-27 in the ABI PRISM 377 DNA Sequencer User’s Manual.
To send a valid calibration file:
Step
Action
1
Make sure the 377 instrument is turned on.
2
From the Window menu of the data collection software, select Manual Control.
3
Open the Fxn Name pull-down menu and select Calibration File Send.
4
Click Execute.
The CCD pixel position value and instrument serial number are sent to the 377
instrument.
Note
5
There is no message or other feedback to this operation.
Quit the data collection software.
Folder Setup The organization of the data collection software folders and files remains the same as
in previous versions. For more information, refer to “Data Collection Software” in the
ABI PRISM 377 DNA Sequencer User’s Manual.
Verify Long Pass Before using Lane Guide reagents for the first time, test the long pass filter on your
Filter instrument. A small number of long pass filters will not detect the bands produced by
Lane Guide reagents. Please see “Testing the Long Pass Filter” on page 16 for the
procedure to test your instrument.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 15 of 26
Testing the Long Pass Filter
Long Pass Filter Test Before using the Lane Guide reagents for the first time, perform the following test to
verify your instrument will detect fifth dye bands. A gel, new or used, is required for this
test.
To test the long pass filter:
Step
Action
1
Power up the 377 instrument.
2
Mount a cassette containing a new or used gel.
3
Open the data collection software.
4
Select File from the menu bar, then select New.
The Create New box appears.
5
Click the Sequence Run icon.
The Run window appears.
6
In the box next to Plate Check Module, click the arrows.
From the pull-down list, select the module PlateCheckfilter_diagn.
7
Click the Plate Check button.
A plate check runs using the selected module.
Page 16 of 26
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
To test the long pass filter: (continued)
Step
8
Action
View the Scan Window.
Note You are looking for the location of the red and black lines relative to the
green and blue, not for how far apart they are.
If you see...
Then the filter...
black and red lines above the blue and
green
passes.
Red
Black
Green
Blue
black and red lines at or below the level
of the blue and green lines
fails.
Green
Blue
Red
Black
9
To amplify the Scan Window in order to better see the lines:
a. Click on the Y-axis:
b. In the dialog box that opens, enter a new range to expand your view.
c. Close the dialog box. Repeat if the view is not sufficiently expanded.
Note
10
Be sure to return the window to its original size once you have finished.
If the filter does not pass, your instrument cannot detect the bands produced by the
Lane Guide reagents. Please contact the service call center for a replacement.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 17 of 26
Loading the Gel
Gel Loading For the procedures for using the Lane Guide reagents and for preparing and loading
Procedure your samples, please refer to the protocol that accompanies the Lane Guide kits,
ABI PRISM Lane Guide Lane Identification Kit (P/N 431804).
IMPORTANT The tracker software will not function correctly unless these procedures and
guidelines are followed.
Page 18 of 26
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Using the Data Collection Software
Introduction The procedure for using the data collection software remains the same except for the
choice of the 5 Dyes setting.
Create a Fifth Dye To create a sample sheet when using Lane Guide reagents:
Lane Identification
Step
Action
Sample Sheet
1
Open the data collection software.
2
Select File from the menu bar, then select New.
The Create New box appears:
3
Click the Sequence Sample icon.
A new untitled Sample Sheet window appears as shown below.
4
In the upper-right corner of the Sample Sheet window, click the arrows next to the
4 Dyes setting.
A pull-down menu appears.
5
Select 5 Dyes.
The setting changes to 5 Dyes.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 19 of 26
Fill in the Sample To fill in the sample sheet:
Sheet
Step
Action
1
In the column Sample Name, enter the names of the samples:
2
Verify or change the DyeSet/Primer files according to the type of chemistry you are
using.
3
Verify the Instrument File setting, or change if necessary.
Note In 5 Dyes mode, you cannot go back and assign a different Instrument File
to the gel file. However, you can change the Instrument File attached to sample files
by using the Sample Manager.
4
In the Project Name column, click the arrow icon.
A pull-down list of project names appears from which you can select the appropriate
project name.
Note
Page 20 of 26
Project names are used only with BioLIMS software.
5
In the Comments column, enter comments.
6
Select File in the menu bar, then select Save.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Create and Fill in the To create and fill in the run sheet:
Run Sheet
Step
1
Action
Select File from the menu bar, then select New.
The Create New box appears.
2
Click the Sequence Run icon.
The Run window appears:
3
In the Lanes box, verify the correct configuration.
To make changes, click the arrows next to the Lanes box and select the correct
configuration from the pull-down list.
4
In the Run Mode box, the correct run mode for the number of lanes appears.
5
In the box next to Sample Sheet, click the arrows.
From the pull-down list, select the newly created sample sheet for the 5 Dyes run.
Note When a 5 Dyes sample sheet is selected, the Plate Check Module, PreRun
Module and Run Module are automatically updated with 5 Dyes modules. If no
5 Dyes modules were defined in the preferences, then the modules default to
<none>. Please refer to “Set Preferences” on page 10.
6
Verify the Instrument File setting, or change if necessary.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 21 of 26
Example of Settings vary depending on the number of lanes, well-to-read distance, etc., but look
Completed Run similar to this:
Window
Analyze the Data When the run is finished, data is analyzed automatically or manually using the
sequencing analysis software. For more information on the sequencing analysis
software program and how to use it to analyze your data, please refer to the following
publications:
Page 22 of 26
ABI PRISM DNA Sequencing Analysis Software User’s Manual (P/N 4306158)
ABI PRISM 377 DNA Sequencer User’s Manual (P/N 4307164)
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Technical Support
To Reach Us on the PE Biosystems web site address is:
Web
http://www.pebiosystems.com/techsupport
We strongly encourage you to visit our web site for answers to frequently asked
questions, and to learn more about our products. You can also order technical
documents and/or an index of available documents and have them faxed to you
through our site (see the “Fax-on-Demand” section below).
Hours for Telephone In the United States and Canada, technical support is available from 5:30 a.m. to 5:00
Technical Support p.m. Pacific time.
To Reach Us by Call Technical Support at 1-800-831-6844, and select the appropriate option (below)
Telephone or Fax in for support on the product of your choice at any time during the call. (To open a
North America service call for other support needs, or in case of an emergency, press 1 after dialing
1-800-831-6844.)
For Support On This Product
Dial 1-800-831-6844, and...
Fluorescent DNA Sequencing
Press
FAX
22
650-638-5891
Fax-on-Demand Free 24-hour access to PE Biosystems technical documents is available by fax.
You can access Fax-on-Demand documents through the internet or by telephone:
If you want to
order...
through the
internet
Then...
Use http://www.pebiosystems.com/techsupport
You can search for documents to order using keywords.
Up to five documents can be faxed to you by title.
by phone from the
United States or
Canada
a. Call 1-800-487-6809 from a touch-tone phone. Have your fax
number ready.
b. Press 1 to order an index of available documents and have it faxed
to you. Each document in the index has an ID number. (Use this as
your order number in step “d” below.)
c. Call 1-800-487-6809 from a touch-tone phone a second time.
d. Press 2 to order up to five documents and have them faxed to you.
by phone from
outside the United
States and
Canada
a. Dial your international access code, then 1-650-556-8419 from a
touch-tone phone.
Have your complete fax number and country code ready (011
precedes the country code).
b. Press 1 to order an index of available documents and have it faxed
to you. Each document in the index has an ID number. (Use this as
your order number in step “d” below.)
c. Call 1-650-556-8419 from a touch-tone phone a second time.
d. Press 2 to order up to five documents and have them faxed to you.
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 23 of 26
To Reach Us by Contact technical support by e-mail for help in the following product areas.
E-Mail
For this product area
Use this e-mail address
Genetic Analysis
[email protected]
PCR and Sequence Detection
[email protected]
Regional Offices If you are outside the United States and Canada, you should contact your local
Sales and Service PE Biosystems service representative.
The Americas
United States
PE Biosystems
850 Lincoln Centre Drive
Foster City, California 94404
Canada (Mississauga, Ontario)
Tel:
Latin America (Del.A. Obregon, Mexico)
Fax:
(650) 570-6667
(800) 345-5224
(650) 572-2743
Tel:
Fax:
Tel:
Fax:
(905) 821-8183
(800) 668-6913
(905) 821-8246
(305) 670-4350
(305) 670-4349
Europe
Austria (Wien)
Hungary (Budapest)
Tel:
Fax:
Tel:
Fax:
01 602 3101
01 602 5174
Benelux (Nieuwerkerk a/d IJssel,
Netherlands)
Tel:
Fax:
Page 24 of 26
31(0) 180 331400
31(0) 180 331409
36-1-258-8410
36-1-256-9802
Italy (Milano)
Tel:
Fax:
(039) 23831
(039) 2383492
Chekia Rep. (Praha)
Norway (Oslo)
Tel:
Fax:
Tel:
Fax:
2 61 22 21 64
2 61 22 21 68
(0) 22 02 1500
(0) 22 02 1501
Denmark (Allerød)
Poland (Warszawa)
Tel:
Fax:
Tel:
Fax:
48 100 400
48 100 401
(48 22) 866 40 10
(48 22) 866 40 20
Finland (Espoo)
Portugal (Lisboa)
Tel:
Fax:
Tel:
Fax:
09 751 72 700
09 751 72 701
(351-1) 386 0997
(351-1) 386 1000
France (Paris)
Russia (Moskva)
Tel:
Fax:
Tel:
Fax:
33-1 69 59 85 85
33-1 69 59 85 00
095 935 8888
095 564 8787
Germany (Weiterstadt)
South Africa (Johannesburg)
Tel:
Fax:
Tel:
Fax:
(0) 6150/ 101 0
(0) 6150/ 101 101
27 11 478 0411
27 11 478 0349
Spain (Madrid)
United Kingdom (Warrington, Cheshire)
Tel:
Fax:
Tel:
Fax:
(91) 806 1200
(91) 804 0414
(01925) 825650
(01925) 282502
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Europe (continued)
Sweden (Stockholm)
Tel:
Fax:
(0)8 619 4400
(0)8 619 4401
All Other European Countries, Middle
East/West Asia, Africa (Langen, Germany)
Tel:
Fax:
49 6103 708 301
49 6103 708 310
Switzerland (Rotkreuz)
Tel:
Fax:
(0) 41 799 7708
(0) 41 790 0676
Japan
Japan (Chiba)
Tel:
Fax:
(0473) 80 8500
(0473) 80 8505
Eastern Asia, China, Oceania
Australia (Scoresby, Victoria)
Malaysia (Kuala Lumpur)
Tel:
Fax:
Tel:
Fax:
(03) 9212 8585/1 800 033 747
(03) 9212 8502
60 3 758 1118
60 3 754 9043
China (Beijing)
Singapore
Tel:
Fax:
Tel:
Fax:
86 10 6238 1156
86 10 6238 1162
65-896-2118
65-896-2147
Hong Kong
Taiwan (Taipei Hsisn)
Tel:
Fax:
Tel:
Fax:
852 2756 6928
852 2756 6968
886 22698 3505
886 22698 3405
Korea (Seoul)
Thailand (Bangkok)
Tel:
Fax:
Tel:
Fax:
822 592 7238
822 532 4908
662 719 6406
662 319 9788
New Data Collection and Sequence Analysis Software Installation Guidelines and Fifth-Dye Sequencing
Page 25 of 26
© Copyright 1999, PE Corporation
For Research Use Only. Not for use in diagnostic procedures.
ABI PRISM and its design is a registered trademark of PE Corporation. ABI, Applied Biosystems, BioLIMS, Factura, Lane Guide, PE, PE Biosystems,
and SNaPshot are trademarks of PE Corporation.
GeneScan is a registered trademark of PE Corporation.
Applescript and Macintosh are registered trademarks of Apple Computer, Inc.
All other trademarks are the sole property of their respective owners.
PE Corporation, formerly the Perkin-Elmer Corporation, is committed to providing the world’s leading technology and information for life scientists. PE
Corporation consists of the PE Biosystems and Celera Genomics businesses. PE Biosystems comprises four divisions—Applied Biosystems, PE
Informatics, PerSeptive Biosystems, and Tropix. PE SCIEX, which is managed through the PerSeptive Biosystems Division, is a joint venture between
PE Corporation and SCIEX, the instrumentation technology division of MDS Inc.
P/N 4313687, Rev. A, Stock No. 106UB11-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement