SRT-N118 - Metrix Electronics Ltd

SRT-N118 - Metrix Electronics Ltd
Assisting the automation
industry since 1986
User manual
METER
SRT-N118
•
•
•
Firmware: v.6.00 or higher
Input type: Pt100/500/1000
Wall mounting case IP 67
Read the user's manual carefully before starting to use the unit or software.
Producer reserves the right to implement changes without prior notice.
2015.01.07
SRT-N118_INSSXEN_v.2.09.002
User manual - METER SRT-N118
CONTENTS
1. BASIC REQUIREMENTS AND USER SAFETY........................................................................................3
2. GENERAL CHARACTERISTICS................................................................................................................4
3. TECHNICAL DATA......................................................................................................................................5
4. DEVICE INSTALLATION............................................................................................................................7
4.1. UNPACKING.......................................................................................................................................7
4.2. ASSEMBLY........................................................................................................................................7
4.3. CONNECTION METHOD...................................................................................................................8
4.4. MAINTENANCE................................................................................................................................16
5. FRONT PANEL DESCRIPTION................................................................................................................17
6. PRINCIPLE OF OPERATION...................................................................................................................17
6.1. MEASUREMENT MODE..................................................................................................................17
6.2. DETECTION OF THE PEAK VALUES............................................................................................18
6.3. CONTROL OF THE RELAY OUTPUTS..........................................................................................19
6.3.1. One threshold mode................................................................................................................20
6.3.2. Two thresholds mode..............................................................................................................21
7. DEVICE PROGRAMMING.........................................................................................................................22
7.1. PROGRAMMING MENU..................................................................................................................22
7.2. PARAMETERS EDITION.................................................................................................................23
7.2.1. Numeric parameters (digit change mode)...............................................................................23
7.2.2. Numeric parameters (slide change mode)..............................................................................23
7.2.3. Switch parameters (“LIST” type).............................................................................................24
7.3. MENU DESCRIPTION.....................................................................................................................24
7.3.1. “rEL1” menu.............................................................................................................................25
7.3.2. “inPt” menu..............................................................................................................................27
7.3.3. ”OutP” menu............................................................................................................................27
7.3.4. ”bri” parameter.........................................................................................................................29
7.3.5. ”HOLd” menu...........................................................................................................................29
7.3.6. ”SECu” menu...........................................................................................................................30
7.3.7. ”rS” menu.................................................................................................................................30
7.3.8. ”Edit” parameter......................................................................................................................31
7.3.9. ”dEFS” parameter....................................................................................................................31
7.3.10. ”SErv” menu..........................................................................................................................31
7.4. MENU STRUCTURE........................................................................................................................32
8. THE ALARM LED......................................................................................................................................34
9. ANALOGUE OUTPUT VALUE CALCULATION......................................................................................34
10. THE MODBUS PROTOCOL HANDLING...............................................................................................34
10.1. LIST OF REGISTERS....................................................................................................................35
10.2. TRANSMISSION ERRORS DESCRIPTION..................................................................................38
10.3. EXAMPLES OF QUERY/ANSWER FRAMES...............................................................................38
11. DEFAULT AND USER'S SETTINGS LIST.............................................................................................41
2
User manual - METER SRT-N118
Explanation of symbols used in the manual:
!
- This symbol denotes especially important guidelines concerning the installation and
operation of the device. Not complying with the guidelines denoted by this symbol
may cause an accident, damage or equipment destruction.
IF THE DEVICE IS NOT USED ACCORDING TO THE MANUAL THE USER IS
RESPONSIBLE FOR POSSIBLE DAMAGES.
i
- This symbol denotes especially important characteristics of the unit.
Read any information regarding this symbol carefully
1. BASIC REQUIREMENTS AND USER SAFETY
!
- The manufacturer is not responsible for any damages caused by
inappropriate installation, not maintaining the proper environmental
conditions and using the unit contrary to its assignment.
- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- If the device is equipped with PE connector, it should be connected to PE wire.
Otherwise PE wire should be connected to GND connector.
- The unit must be properly set-up, according to the application. Incorrect
configuration can cause defective operation, which can lead to unit damage or
an accident.
- If in the case of a unit malfunction there is a risk of a serious threat to the
safety of people or property additional, independent systems and
solutions to prevent such a threat must be used.
- The unit uses dangerous voltage that can cause a lethal accident. The unit
must be switched off and disconnected from the power supply prior to
starting installation of troubleshooting (in the case of malfunction).
- Neighbouring and connected equipment must meet the appropriate standards
and regulations concerning safety and be equipped with adequate overvoltage
and interference filters.
- Do not attempt to disassemble, repair or modify the unit yourself. The unit
has no user serviceable parts. Defective units must be disconnected and
submitted for repairs at an authorized service centre.
3
User manual - METER SRT-N118
!
- Do not use the unit in areas threatened with excessive shocks, vibrations, dust,
humidity, corrosive gasses and oils.
- Do not use the unit in areas where there is risk of explosions.
- Do not use the unit in areas with significant temperature variations, exposure to
condensation or ice.
- Do not use the unit in areas exposed to direct sunlight.
- Make sure that the ambient temperature (e.g. inside the control box) does not
exceed the recommended values. In such cases forced cooling of the unit must
be considered (e.g. by using a ventilator).
!
The unit is designed for operation in an industrial environment and must
not be used in a household environment or similar.
2. GENERAL CHARACTERISTICS
The SRT-N118 meter is equipped with Pt 100/Pt 500/Pt 1000 type input, with automatic
connection recognition ( three or four wire sensor). The measurement range spans from
-100 °C to +600 °C, and input is fully linearised accordingly to PN-EN60751+A2:1999
standard. Result is showed on 4-digit LED display.
The device can be equipped with two relay (or OC type) outputs. Optionally SRT-N118
with one relay (or OC type) output can be equipped with active current output, passive isolated
current output or active voltage output. Device SRT-N118 is equipped with RS-485 / Modbus
RTU communication interface and 24V/100mA supply output for free use. The meter can be
ordered in two power supply versions.
The device has 4 buttons being used for main presets programming. To get high
protection level, the keyboard is mounted under transparent cover. To allow user to change
presets without opening the cover, an IR sensor is mounted. Remote controller keyboard is
equivalent to the device keyboard (Note, that remote controller is not a part of the SRT-N118
set – it is an additional equipment).
SRT-N118 can be used for controlling and regulation of processes need proportional and
threshold control like: temperature processes (heating or cooling), valves controlling or other.
4
User manual - METER SRT-N118
3. TECHNICAL DATA
Power supply voltage
(depending on version)
External fuse (required)
Power consumption
85...230...260V AC/DC; 50 ÷ 60 Hz (separated)
or 19...24...50V DC and 16...24...35V AC (separated)
T - type, max. 2 A
max. 5 VA @ 85 ÷ 260V AC/DC
max. 5 VA @ 16V ÷ 35V AC
max. 5 W @ 19V ÷ 50V DC
Measurement input
Pt 100/ Pt 500/Pt 1000 type with automatic
connection recognition ( 3 or 4-wires)
Measurement range
-100°C ÷ +600°C
Measurement accuracy
± 0,1% @ 25°C; ± one digit
Measurement wires resistance
max. 20 Ω (every wire)
Sensor power supply output
24V +5%, -10% / max. 100 mA, stabilized
Relay output
0, 1 or 2 NO, 1A/250V AC (cos ϕ = 1)
OC-type output
0, 1 or 2; 30mA / 30VDC / 100mW
Active current output
(optional, for one relay or one
OC-type output version only)
range max. 0 ÷ 24 mA
Load resistance max.
700 Ω
Passive isolated current output
(optional, for one relay or one
OC-type output version only)
range max. 2.8 ÷ 24 mA
Supply voltage
Us = 9.5 ÷ 36V
Load resistance max.
(Us – 9.5V) / 24mA [kΩ]
Active voltage output
(optional, for one relay or one
OC-type output version only)
range max. 0 ÷ 11V
Load resistance min.
2000 Ω
Temperature stability
50 ppm / °C
5
User manual - METER SRT-N118
Communication interface
RS 485, 8N1 and 8N2, Modbus RTU, not separated
Baud rate
1200 bit/s ÷ 115200 bit/s
Display
(depending on version)
LED, 4 digit, 20mm height, red or
LED, 4 digit, 38mm height, green
Data memory
non-volatile memory, EEPROM type
Protection level
IP 67
Housing type
Housing material
Housing dimensions
without glands:
with glands:
wall mounted
ABS + fibreglass
Operating temperature
0°C do +50°C
or -20°C to +50°C
Storage temperature
-10°C do +70°C
or -20°C to +70°C
Humidity
Altitude
110 x 80 x 67 mm
110 x 105 x 67 mm
5 to 90% no condensation
up to 2000 meters above sea level
Screws tightening max. torque
0,5 Nm
Max. connection leads cross section 3 mm2 (for connectors 1÷6) or
2 mm2 (for connectors 7÷16)
Safety requirements
according to: PN-EN 61010-1
installation category: II
pollution degree: 2
voltage in relation to ground: 300V AC
insulation resistance: >20MΩ
insulation strength between power supply and
input/output terminal: 1min. @ 2300V
insulation strength between relays terminal:
1min. @ 1350V
EMC
!
6
according to: PN-EN 61326-1
This is a class A unit. In a residential or a similar area it can cause radio
frequency interference. In such cases the user can be requested to use
appropriate preventive measures.
User manual - METER SRT-N118
4. DEVICE INSTALLATION
The unit has been designed and manufactured in a way assuring a high level of user
safety and resistance to interference occurring in a typical industrial environment. In order to
take full advantage of these characteristics installation of the unit must be conducted correctly
and according to the local regulations.
!
- Read the basic safety requirements on page 3 prior to starting the installation.
- Ensure that the power supply network voltage corresponds to the nominal
voltage stated on the unit’s identification label.
- The load must correspond to the requirements listed in the technical data.
- All installation works must be conducted with a disconnected power supply.
- Protecting the power supply connections against unauthorized persons must be
taken into consideration.
4.1. UNPACKING
After removing the unit from the protective packaging, check for transportation damage. Any
transportation damage must be immediately reported to the carrier. Also, write down the unit
serial number located on the housing and report the damage to the manufacturer.
Attached with the unit please find:
- user’s manual,
- warranty,
4.2. ASSEMBLY
!
!
- Disconnect the power supply prior to starting assembly.
- Check the connections are wired correctly prior to switching the unit on.
To install device on the wall, a pinholes should be made. Figure 4.1 presents
dimensions of the device and distances between holes. The back side of the device
has four mounting holes. This part of the case should be mounted to a wall by
screws.
7
User manual - METER SRT-N118
110 mm
67 mm
60 mm
80 mm
90 mm
.4
ø4
ø8
.4
Figure 4.1. Device and assembly dimensions
4.3. CONNECTION METHOD
Caution
!
- Installation should be conducted by qualified personnel . During installation all
available safety requirements should be considered. The fitter is responsible for
executing the installation according to this manual, local safety and EMC
regulations.
- The unit is not equipped with an internal fuse or power supply circuit breaker.
Because of this an external time-delay cut-out fuse with a small nominal current
value must be used (recommended bipolar, max. 2A) and a power supply circuitbreaker located near the unit. In the case of using a monopolar fuse it must be
mounted on the phase cable (L).
- The power supply network cable diameter must be selected in such a way that in
the case of a short circuit of the cable from the side of the unit the cable shall be
protected against destruction with an electrical installation fuse.
- Wiring must meet appropriate standards and local regulations and laws.
- In order to secure against accidental short circuit the connection cables must be
terminated with appropriate insulated cable tips.
- Tighten the clamping screws. The recommended tightening torque is 0.5 Nm.
Loose screws can cause fire or defective operation. Over tightening can lead to
damaging the connections inside the units and breaking the thread.
- In the case of the unit being fitted with separable clamps they should be inserted
into appropriate connectors in the unit, even if they are not used for any
connections.
- Unused terminals (marked as n.c.) must not be used for connecting any
connecting cables (e.g. as bridges), because this can cause damage to the
equipment or electric shock.
8
User manual - METER SRT-N118
!
- If the unit is equipped with housing, covers and sealing to, protecting against
water intrusion, pay special attention to their correct tightening or clamping. In the
case of any doubt consider using additional preventive measures (covers, roofing,
seals, etc.). Carelessly executed assembly can increase the risk of electric shock.
- After the installation is completed do not touch the unit’s connections when it is
switched on, because it carries the risk of electrical shock.
Due to possible significant interference in industrial installations appropriate measures
assuring correct operation of the unit must be applied. To avoid the unit of improper
indications keep recommendations listed below.
–
Avoid running signal cables and transmission cables together with power supply cables
and cables controlling inductive loads (e.g. contactors). Such cables should cross at
a right angle.
–
Contactor coils and inductive loads should be equipped with interference protection
systems, e.g. RC-type.
–
Use of screened signal cables is recommended. Signal cable screens should be
connected to the earthing only at one of the ends of the screened cable.
–
In the case of magnetically induced interference the use of twisted pair of signal cables is
recommended. Twisted pair (best if shielded) must be used with RS-485 serial
transmission connections.
–
In the case of measurement or control signals are longer than 30m or go outside of the
building then additional safety circuits are required.
–
In the case of interference from the power supply side the use of appropriate interference
filters is recommended. Bear in mind that the connection between the filter and the unit
should be as short as possible and the metal housing of the filter must be connected to
the earth with the largest possible surface. The cables connected to the filter output must
not be run with cables with interference (e.g. circuits controlling relays or contactors).
6 mm
max. 1.6 mm
max. 2 mm
Connection of the power supply, and the measurement and controlling signals should be
made by clamping connectors mounted inside the housing.
a)
b)
5 mm
Figure 4.2. Recommended dimensions of cable stripping
a) for big connectors (1 to 6), b) for small connectors (7 to 16)
9
User manual - METER SRT-N118
Figure 4.3. Method of connecting cables to the clamping connectors
!
All connections must be made while power supply is disconnected !
12 11 10
R1
R2
(option)
(option)
6 5
4 3
RS - 485
Pt100/500/1000
Uo
-
Pt100/500/1000
Figure 4.4. Terminals description (relay outputs)
10
(depending
on version)
+
24V (+5%, -10%)
Imax = 100 mA
2 1
Power supply
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
User manual - METER SRT-N118
12 11 10
OC1, OC2: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
(option)
Pt100/500/1000
+
+
6 5
-
+
4 3
-
Uo
2 1
Power supply
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
-
OC2
(option)
24V (+5%, -10%)
Imax = 100 mA
Pt100/500/1000
(depending
on version)
OC1
RS - 485
Figure 4.5. Terminals description (OC-type outputs)
12 11 10
R1
(option)
ACTIVE
current output
(option)
6 5
4 3
RS - 485
Pt100/500/1000
Uo
2 1
-
24V (+5%, -10%)
Imax = 100 mA
Pt100/500/1000
(depending
on version)
+
- +
Power supply
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
Figure 4.6. Terminals description (relay and active current outputs)
12 11 10
OC1: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
ACTIVE
OC1 current output
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
+
Uo
-
24V (+5%, -10%)
Imax = 100 mA
Pt100/500/1000
(option)
+
- +
6 5
4 3
-
2 1
(depending
on version)
Pt100/500/1000
Power supply
RS - 485
(option)
Figure 4.7. Terminals description (OC-type and active current outputs)
11
User manual - METER SRT-N118
12 11 10
(option)
R1
Passive, isolated
current output
4÷20mA
(option)
6 5
4 3
RS - 485
Pt100/500/1000
Uo
-
24V (+5%, -10%)
Imax = 100 mA
Pt100/500/1000
(depending
on version)
+
2 1
Power supply
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
Figure 4.8. Terminals description (relay and passive current outputs)
12 11 10
OC1: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
OC1
(option)
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
-
+
Uo
-
24V (+5%, -10%)
Imax = 100 mA
Pt100/500/1000
+
6 5
4 3
2 1
(depending
on version)
Pt100/500/1000
Power supply
RS - 485
Passive, isolated
current output
4÷20mA
(option)
Figure 4.9. Terminals description (OC-type and passive current outputs)
12
User manual - METER SRT-N118
12 11 10
R1
(option)
ACTIVE
voltage output
(option)
6 5
4 3
RS - 485
Pt100/500/1000
Uo
2 1
-
24V (+5%, -10%)
Imax = 100 mA
Pt100/500/1000
(depending
on version)
+
- +
Power supply
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
Figure 4.10. Terminals description (relay and active voltage outputs)
12 11 10
OC1: Umax = 30V DC,
Imax = 30mA, Pmax = 100mW
ACTIVE
OC1 voltage output
Pt100/500/1000
n.c.
13 12 11 10 9 8 7
PE
DATA+
DATA-
GND
16 15 14
+
Uo
-
24V (+5%, -10%)
Imax = 100 mA
Pt100/500/1000
(option)
+
- +
6 5
4 3
-
2 1
(depending
on version)
(option)
Power supply
RS - 485
Figure 4.11. Terminals description (OC-type and active voltage outputs)
Temperature sensor can be connected to the device in typical 4-wire circuit (Figure 4.12a) or
3-wire circuit (Figure 4.12b). Due to precision of measurement 4-wire circuit is recommended.
i
If 2 wire circuit is used it is recommended to connect sensor accordingly to
Figure 4.12c. (4-wires circuit with shorted pins 12+11 and 10+9). In this case, the
resistance of wires should be as small as possible, to avoid of measurement errors.
Measured value can be corrected (constant correction) using „toFS” parameter from
menu „inPt”. Due to low precision 2-wire connection is not recommended.
When 4-wires or 2-wires connection is used, the resistance of particular wires (Ra ÷ Rd)
CAN BE DIFFERENT. When 3-wires connection is used, the resistance of particular wires
(Ra ÷ Rd) MUST BE IDENTICAL to enable proper compensation of it's resistance. The
resistance of particular wire should not be greater than 20 Ω .
13
User manual - METER SRT-N118
a)
b)
12 11 10 9
12 11 10 9
c)
12 11 10 9
n.c.
Ra
Rb
Rc
Rd
Ra
Rb
Rc
Rb
Pt100
Pt100
Ra, Rb, Rc, Rd can be different
Ra = Rb = Rc
Rc
Pt100
Rb, Rc can be different
Figure. 4.12. Connection of sensors:
a) 4-wires circuit; b) 3-wires circuit; c) 2-wires circuit
i
The connection circuit should not be changed while unit is powered. Every change
of connection while the unit is powered causes measurement errors by several
seconds after change.
R1
R2
N L
6 5 4 3
2 1
FUSE
FUSE
N
L
Depending on version:
85...230...260V AC/DC; 50 ÷ 60 Hz or
19...24...50V DC and 16...24...35V AC
Figure 4.13. Connection of power supply and relays
!
14
Contacts of relay outputs are not equipped with spark suppressors. While use
the relay outputs for switching of inductive loads (coils, contactors, power
relays, electromagnets, motors etc.) it is required
to use additional
suppression circuit (typically capacitor 47nF/ min. 250VAC in series with
100R/5W resistor), connected in parallel to relay terminals or (better) directly
on the load. In consequence of using the suppression circuit, the level of
generated electromagnetic disturbances is lower, and the life of relay contacts
rises.
User manual - METER SRT-N118
a)
b)
L
6 5
L
!
6 5
!
N
N
Figure 4.14. Examples of suppression circuit connection:
a) to relay terminals; b) to the inductive load
Uo
Uo
OC1
-
-
6 5
8 7
6 5
8 7
+
OC1
+
+
-
-
+
Logic controller
-
+
R
2k2
voltage input
24V
LED 10 mA
Figure 4.15. Example of OC-type outputs connection
ACTIVE
Current output
-
+
4 3
Logic controller
+
-
Current input
0-20 mA
Figure 4.16. Example of active current outputs connection
(for device with active current output only)
15
User manual - METER SRT-N118
Uo
PASSIVE
Current output
8 7
4 3
+
Logic controller
+
-
Current input
4-20mA
!
Isolation loss
Figure 4.17. Example of passive current outputs connection
(for device with passive current output only)
ACTIVE
voltage output
-
+
4 3
Logic controller
+
voltage input
0 - 10V
Figure 4.18. Example of active voltage outputs connection
(for device with active voltage output only)
4.4. MAINTENANCE
The unit does not have any internal replaceable or adjustable components available to
the user. Pay attention to the ambient temperature in the room where the unit is operating.
Excessively high temperatures cause faster ageing of the internal components and shorten the
fault-free time of the unit's operation.
In cases where the unit gets dirty do not clean with solvents. For cleaning use warm water with
small amount of detergent or in the case of more significant contamination ethyl or isopropyl
alcohol.
!
Using any other agents can cause permanent damage to the housing.
Product marked with this symbol should not be placed in municipal waste. Please
check local regulations for disposal of electronic products.
16
User manual - METER SRT-N118
5. FRONT PANEL DESCRIPTION
alarm LED indicator (AL)
AL
R1
Thresholds exceeding
LED indicators (R)
R2
display
infrared
receiver
ESC
MENU
ENTER
programming pushbuttons
Symbols and functions of push-buttons:
ESC
MENU
ENTER
Symbol used in the manual: [ESC/MENU]
Functions:
• Enter to main menu ( press and hold by at least 2 sec.)
• Exit the current level and Enter to previous menu (or measure mode)
• Cancel the changes made in parameter being edited
Symbol used in the manual: [ENTER]
Functions:
• Start to edit the parameter
• Enter to the sub-menu,
• Confirmation of changes made in parameter being edited
Symbol used in the manual: [^] [v]
Functions:
• Change of the present menu,
• Modification of the parameter value,
• Change of the display mode.
6. PRINCIPLE OF OPERATION
After turning the power supply on, device ID and software version are showed on the
display, next the controller goes to the measurement mode.
6.1. MEASUREMENT MODE
In the measure mode, the measurement results, are displayed on the display. If the result
of measurement exceeds the permissible measurement range, warning ”-Hi-” or ”-Lo-” is
displayed rather than calculated result, depends on exceeded value. The warning can be
effect of measurement circuit malfunction. In that case “-Lo-” means shortcut and “-Hi-”
means break of measurement circuit.
17
User manual - METER SRT-N118
In the measurement mode user can check main thresholds values. After pressing [^] or
[v] button, name of the threshold (e.g. ”rEL1”) and his value will be displayed on the display
in alternating mode. If [^] or [v] will be pressed in 5 sec again, the next threshold will be
displayed, else the device comes back to the measurement mode. If a free access is enabled
(see description of ”SECu” menu), user can change the value of particular threshold pressing
button [ENTER] (see: PARAMETERS EDITION).
All accessible parameters can be changed by entering the menu (see: DEVICE
PROGRAMMING). Use the local keyboard or the remote controller to do it. (Note: all
parameters can be remote changed via RS-485 interface).
i
Configuration of the device (via menu or RS-485 interface) does not stop
measures.
6.2. DETECTION OF THE PEAK VALUES
The SRT-N118 controller is equipped with peaks detection function. It can detect a peaks
of the input signal and display their values. Presets connected with this function are placed in
”HOLd” menu (see description of ”HOLd” menu). The detection of the peak can be done if
the measured signal raises and drops of value at least equal to parameter ”PEA”. Detected
peaks are displayed during the time defined by parameter ”timE”. If a new peak will be
detected while one is displayed, this new peak will be displayed and display time counter will
be cleared (Figure 6.1). If no peaks are detected while time ”timE” elapses, device starts to
show the current value of input signal again. If „HdiS”=”HOLD” then setting parameter
"timE"=0.0 causes holding peak value until [ESC] button is pressed. If „HdiS”=”rEAL” then
value "timE"=0.0 means no holding. Displaying peak value is signalized by flashing most right
decimal point.
The relays/LEDs and analogue outputs can be controlled depend on the current value of
input signal or the peak value (see ”HOLd” menu).
measure
”timE”
”timE”
”PEA”
”PEA”
real measurement result
display value
Figure 6.1. Process of peaks detection
18
time
User manual - METER SRT-N118
6.3. CONTROL OF THE RELAY OUTPUTS
The control of the object (measured signal) is realized via relay outputs. Front panel
LEDs named „R” indicates the state of particular relay output.
i
If device is not equipped with one or more relay outputs, menus refer to this relays
are available, but apply to LED indicators only. In such case LEDs indicates
exceeding of particular thresholds.
Modes of the control can be changed depend on the values of parameters “SEtP”, “SEt2”,
“HYSt”, “modE”, “t on”, “toFF”, “unit” and “AL”. Depend on “modE” parameter, relays
can be not used or controlled over one or two thresholds values.
If one threshold is used (Figure 6.2) the relay can be turned on (“modE” = ”on”) or off
(“modE” = ”oFF”) when the input signal value is contained in zone A. If two thresholds are
used (Figure 6.3) the relay will be turned on when value of input signal is contained in zone A
(“modE” = ”in”) or zone B (“modE” = ”out”) and turned off if the signal is contained in the
second one.
state of
relay/LED
”SEtP” parameter
zone B
zone A
measure
”HYSt” parameter
Figure 6.2. One threshold control of the relay/LED outputs
state of
relay/LED
”SEtP” or ”SEt2” parameter
zone B
zone A
zone B
measure
”HYSt” parameter
Figure 6.3. Two threshold control of the relay/LED outputs
i
The relay outputs and LEDs (named R) can be controlled depend on both - the
current value and the peak value (when peak detection is active) of the input signal.
19
User manual - METER SRT-N118
6.3.1. One threshold mode
Figure 6.4 presents the principle of relay outputs operation for one threshold mode, and
an example values of other parameters.
displayed value
a)
zone A
tB
tA
B
A
tC
b)
c)
d)
e)
relay state
(modE = oFF
t on = 0
toFF = 0)
relay state
(modE = on
t on > 0
toFF > 0)
relay state
(modE = oFF
t on > 0
toFF > 0)
“SEtP” parameter
(expected signal value)
tD
BOFF B
ON
C
zone B
relay state
(modE = on
t on = 0
toFF = 0)
measured
signal
D
DOFF
DON
“HYSt” parameter
(allowed signal
deviation)
time
closed
open
time
closed
open
time
closed
open
time
closed
“t on”
parameter
“toFF”
parameter
open
time
“toFF”
parameter
“t on”
parameter
Description:
A, B, C, D
- points where measured signal exceeds border values (expected value ± allowed deviation)
BON ,BOFF ,DON ,DOFF - relays state changes moments: (for “t on” > 0, “toFF” > 0)
tA , tB , tC , tD
- time periods while input signal is in zone A or zone B
Figure 6.4. Principle of LED/relay output operation for one threshold mode
Parameter “SEtP” sets a threshold of the relay, and parameter “HYSt” sets a
hysteresis of the relay (Figure 6.4 a). The relay can change his state only when input value
exceeds (over or under) border value and tA ,tB ,tC ,tD times (Figure 6.4) are bigger than the
time defined by parameters “t on”, “toFF” and “unit”. Border values means values equal
threshold+hysteresis and threshold-hysteresis respectively.
If “t on” and “toFF” parameters are set to “0”, then the relay state will be changed
as soon as input value exceeds any of the border values (see points A and C, Figure 6.4 a,
b, c).
If values of “t on” or/and “toFF” are positive, then relay state will be turned on if the
input value exceeds the border values and stay bigger (or lower) during at least
“t on” (see points BON, DON, Figure 6.4 a, d, e). Similarly, the relay will be turned off if time
“toFF” elapse since the input signal value exceeds any of the border values (see points
BOFF, DOFF, Figure 6.4 a, d, e).
If tA ,tB ,tC or tD (when input signal stay in zone A or zone B) are lower than parameters
“t on” or “toFF”, the relay will not change his state (see points A and C, Figure 6.4 a, d, e).
20
User manual - METER SRT-N118
The state of relay output while the input value exceeds the border values (points A, B, C,
D) is described by parameter “modE”. The relay can be turned on (“modE” = ”on”), or
turned off (“modE” = ”oFF”) when input signal value is contained in zone A (Figure 6.4 a).
The parameter “AL” allow user to set the relay output behaviour in critical situations (e.
g. Input values exceeds permissible measurement range). User can select that the relays
will be turned on, turned off,or not changed in critical situations.
All parameters connected with relay outputs are described in paragraph ”rEL1” menu.
6.3.2. Two thresholds mode
displayed value
tA
tB
tC
COFF CON
zone B
tD
measure
d signal
tE
“HYSt” parameter
C
BON
BOFF
a)
zone A
A
D
E
B
EOFF
EON
“SEtP” or “SEt2”
parameter
“HYSt” parameter
zone B
b)
c)
d)
e)
relay state
(modE = in
t on = 0
toFF = 0)
relay state
(modE = out
t on = 0
toFF = 0)
time
closed
time
closed
open
time
relay state
(modE = in
t on > 0
toFF > 0)
relay state
(modE = out
t on > 0
toFF > 0)
open
closed
open
time
“toFF” parameter
“t on” parameter
open
“t on” parameter
closed
time
“toFF” parameter
“t on” parameter
“toFF” parameter
Objaśnienie:
A, B, C, D, E
- points where measured signal exceeds border values (expected value ± allowed deviation)
BON ,BOFF ,CON ,COFF ,EON ,EOFF
- relays state changes moments: (for “t on” > 0, “toFF” > 0)
tA , tB , tC , tD , tE
- time periods while input signal is in zone A or zone B
Figure 6.5. Principle of LED/relay output operation for two thresholds mode
21
User manual - METER SRT-N118
Figure 6.5 presents the principle of relay outputs operation for two thresholds mode, and
an example values of other parameters. In this mode parameter “SEt2” is accessible in
common with “SEtP”, this parameter describes a second threshold of the relay output. The
parameters “HYSt”, “modE”, “t on”, “toFF”, “unit” and “AL” are connected with both
“SEtP” and “SEt2” thresholds. While the controlling process, the relay output changes his
state depends of both “SEtP” and “SEt2” thresholds in similar way as it was described in one
threshold mode.
If two threshold mode is used, “modE” parameter defines state of the relay output when
the input value occurs in a particular zone defined by border values of both thresholds. The
relay can be turned on if the input value is contained in zone A (“modE” = ”in”) or zone B
(“modE” = ”out”) and turned off if it is contained in the second one (Figure 6.5).
i
The sequence of thresholds “SEtP” and “SEt2” can be set in any order, due to the
control of relay outputs is done depend on difference between thresholds values
(zone A ) and outside of threshold values (zone B).
7. DEVICE PROGRAMMING
The device menu allow user to set all parameters connected to operation of
measurement input, control modes, critical situations behaviour, communication via RS-485
and access settings. The meaning of the particular parameters is described in paragraph
MENU DESCRIPTION.
Some of the parameters can be accessed without menu entering (quick view mode).
After pressing [^] or [v] button, name of the threshold (e.g.”rEL1”) and his value will be
displayed on the display in alternating mode. If [^] or [v] will be pressed in 5 sec again, the
next threshold will be displayed, else the device comes back to the measurement mode. If a
free access is enabled (see description of ”SECu” menu), user can change the value of
particular threshold pressing button [ENTER] (see: PARAMETERS EDITION).
i
If particular parameter has been changed and confirmed in quick view mode, its
new value is displayed in alternating mode with parameter name by few seconds.
Confirmed changes may be checked or user can switch viewed parameter pressing
[^] or [v] button.
7.1. PROGRAMMING MENU
To enter main menu (being in the measurement mode) operator must to press and hold
at least 2 sec. [ESC/MENU] button.
If the user password is defined (see parameter “Scod“, menu ”SECU”), operator have
to enter correct one before proceeding to menu options . Entering of the passwords is similar
to the edition of numeric parameters (see: PARAMETERS EDITION ), however presently editing
digit is showed only on the display, other digits are replaced by “-” sign.
After entering of last digit of the password first menu position will be displayed (if the password
is correct) or warning ”Err” in other case.
!
22
Pay attention when device parameters are being changed. If it is possible, turn off
controlled installation (machine).
User manual - METER SRT-N118
Functions of the buttons while sub-menu and parameters choice:
Selection of sub-menu or parameter for editing. Name of selected item (submenu or parameter) is displayed.
ENTER
Operation of [ENTER] button depend on present menu position:
• if the name of some sub-menu is displayed - enter this sub-menu; name
of the first parameter (or next level sub-menu) is displayed,
• if the name of some parameter is displayed - enter the edition of this
parameter; present value of the parameter is displayed,
MENU
[ESC/MENU] button allow user to exit present menu level and goes to upper
level menu (or measurement mode).
i
After about 1 min. since last use of the buttons, device exits the menu mode and
returns to the measurement mode (only if no parameters are in editing mode).
ESC
7.2. PARAMETERS EDITION
To start edition of any parameter user should select name of desired one using [^] [v]
buttons and then press [ENTER].
7.2.1. Numeric parameters (digit change mode)
Numerical parameters are displayed as decimal numbers. The mode of its new value
entering depends on chosen edit method ( see parameter „Edit”).
In mode “by digit” („Edit”=”dig”) pressing one of the keys [^] or [v] causes change of
current position (flashing digit) or the sign (+/-). Short pressing of the [ENTER] button causes
change of the position (digit).
Press [ENTER] at least 2 seconds to accept the changes, after that question ”SEt?” is
displayed, and user must to confirm (or cancel) the changes. To conform changes (and story it
in EEPROM) press [ENTER] button shortly after ”SEt?” is displayed. To cancel the changes
press [ESC] button shortly after ”SEt?” is displayed. After that device returns to the menu.
7.2.2. Numeric parameters (slide change mode)
In “slide change” mode („Edit”=”Slid”), buttons [^] and [v] has different functions.
To increase edited value press (or press and hold) [^] button only, the increasing
became quickest as long as button [^] is pressed. To slow down the increasing, button [v] can
be used. If [v] is pressed shortly (and button [^] is still pressed), increasing slow down for
a moment only, if [v] is pressed and held while button [^] is still pressed the increasing slow
down and will be kept on lower speed.
To decrease edited value press (or press and hold ) [v] button only. The decreasing
became quickest as long as button [v] is pressed. To slow down the decreasing, button [^]
can be used. If [^] is pressed shortly (and button [v] is still pressed), decreasing slow down for
a moment only, if [^] is pressed and held while button [v] is still pressed the decreasing slow
down and will be kept on lower speed.
23
User manual - METER SRT-N118
Press [ENTER] at least 2 seconds to accept the changes, after that question ”Set?” is
displayed, and user must to confirm (or cancel) the changes. To conform changes (and story it
in EEPROM) press [ENTER] button shortly after ”SEt?” is displayed. To cancel the changes
press [ESC] button shortly after ”SEt?” is displayed. After that device returns to the menu.
7.2.3. Switch parameters (“LIST” type)
Switch parameters can be described as a sets of values (a lists) out of which only one of
the options available on the list can be selected for the given parameter. Options of switching
parameter are selected using [^], [v] keys.
Short pressing of [ENTER] causes in displaying of the acknowledge question (”SEt?”). If
key [ENTER] is pressed again, the changes are accepted, stored in EEPROM end the edition
process finished. Pressing the key [ESC] after ”SEt?” causes in cancelling of made changes
and returning to menu.
Functions of buttons when editing numeric and switching parameters:
While editing numeric parameter:
• change of current (flashing) digit
• slide change of value (acceleration, deceleration, direction change)
While editing switch parameter - selection of switch parameter.
ENTER
ESC
MENU
If numerical parameter is being edited, a short press of [ENTER] button
change edited position. A long press of [ENTER] button (at lest 2 sec.)
causes of display a ”SEt?” ask, which allow user to make sure if change of
the parameter value is correct. If switch parameter is being edited, a short
press of [ENTER] button causes of display a ”SEt?” ask. When [ENTER]
button is pressed again (while ”SEt?” is displayed) the new value of the
parameter is stored in EEPROM memory.
Pressing this button operator can cancel the changes done up to now (if they
were not approved by [ENTER] button after the ”SEt?” ask) and come back
to menu
7.3. MENU DESCRIPTION
“- - - -”
i
24
- password checking. If some password different from „0000” is set, then every
enter to main menu follows the entering of password. If entered password is
correct then first menu position will be displayed else warning ”Err”, and unit
returns to measurement mode.
Due to problem with direct displaying of “m” and “K” letters, they are exchanged
with special signs “ “ for “m” and “ " for K respectively. However, in user manual
letters „m” and “K” are used to make it more readable (example: “modE”, “tc K”).
User manual - METER SRT-N118
7.3.1. “rEL1” menu
This menu allows to configure the operation mode of relays and LEDs marked „R” (e.g. „R1”).
If there are few relay outputs available, then every output has its own configuration menu
(e.g. menu „rEL2” for relay (LED) „R2”). Principle of the relays operation is described in
paragraph CONTROL OF THE RELAY OUTPUTS.
i
•
•
The relay outputs and LEDs (named R) can be controlled depend on both - the
current value and the peak value (when peak detection is active) of the input
signal.
If device is not equipped with one or more relay outputs, menus refer to this
relays are available, but apply to LED indicators only. In such case LEDs
indicates exceeding of particular thresholds.
“SEtP”
- first threshold of the relay (range -999 ÷ 9999). Negative values can be input by
selecting a “-” sign on first digit (to change value use [^] and [v] buttons).
Threshold is the medium value of relay hysteresis.
“SEt2”
- second threshold of the relay (range -999 ÷ 9999). Negative values can be input
by selecting a “-” sign on first digit ( to change value use [^] and [v] buttons). This
threshold is accessible when ”modE” parameter is set to „in” or „out” value.
Threshold is the medium value of relay hysteresis.
“HYSt”
i
- hysteresis of relay (range 0 ÷ 999). Full hysteresis of the relay is equal to 2x
“HYSt” parameter. The relay state can change when an input signal is out of
threshold-hysteresis to threshold+hysteresis zone.
Presented parameters should be set to ensure that ”SEtP” + ”HYSt”,
”SEt2” + ”HYSt”, ”SEtP” - ”HYSt” or ”SEt2” - ”HYSt” does not exceed the
measure range. Additionally, in two threshold mode (“modE”= „in” or „out”), the
hysteresis for both thresholds must not cover each other (in other case relay can't
change his state).
“modE” - relay operation mode:
“noAC” - the relay is not active (permanent turned off)
“on”
- one threshold mode, the relay is turned ON when input signal exceeds
SEtP + HYSt value, and is turned off back when the input signal became
lower than SEtP – HYSt,
“oFF”
- one threshold mode, the relay is turned OFF when input signal exceeds
SEtP + HYSt value, and is turned on back when the input signal became
lower than SEtP – HYSt,
“in”
- two threshold mode, the relay is turned ON when the input signal is
bigger than “lower threshold + HYSt” and lower than “bigger
threshold – HYSt”, and turned off when the input signal is contained in
the second zone. The bigger threshold means bigger one of “SEtP”
and “SEt2” thresholds, the lower threshold” means lower one of
“SEtP” and “SEt2” thresholds.
25
User manual - METER SRT-N118
“out”
- two threshold mode, relay is turned ON when the input value is bigger
than “bigger threshold + HYSt” and lower than “lower threshold –
HYSt”, and turned on when the input signal is contained in the second
zone. The bigger threshold means bigger one of “SEtP” and “SEt2”
thresholds, the lower threshold” means lower one of “SEtP” and
“SEt2” thresholds.
“modb” - the relay is controlled via RS-485 interface, independently on the input
signal.
i
•
•
LEDs light when relays are closed, independently of relays' mode.
When power supply fail, unit do not store relays state selected by RS-485
interface.
“t on”
- turn on delay time, the relay is turned on with delay equal “t on” if the input value
exceeds appropriate border value (defined with threshold and hysteresis), at
least “t on” time. “t on” range 0 ÷ 99.9, defined with 0.1 sec. resolution. Unit of
this parameter is set by “unit” parameter.
“toFF”
- turn off delay time, the relay is turned off with delay equal “toFF” if the input value
exceeds appropriate border value (defined with threshold and hysteresis), at
least “toFF” time. “toFF” range 0 ÷ 99.9, defined with 0.1 sec. resolution. Unit of
this parameter is set by “unit” parameter.
i
“unit”
If time when the input signal exceeds some border value is shorter than “t on” or
“toFF” time, the relay do not change its state (see paragraph: CONTROL OF
THE RELAY OUTPUTS).
- unit of time for “t on” i “toFF” parameters. Can be set on one of two values:
“min”
“SEC”
“AL”
- minutes,
- seconds.
- this parameter defines the relay reaction when some critical situations occurs:
“noCH”
“on”
“oFF”
- relay do not change his state,
- relay will be turned on,
- relay will be turned off.
If parameter “modE” is set to “on” , “oFF”, “in” or “Out” the “critical situation”
means that allowable measurement range is exceeded.
If parameter “modE” is set to “modb”, the “critical situation” means
communication delay (when no data is received) longer than “mbtO” parameter
(see description: “rS” menu).
26
User manual - METER SRT-N118
i
•
•
If option “noCH” is selected for “AL” parameter, behaviour of the relay may
depend on “FiLt” parameter in some cases. If “FiLt” is set to big value and the
input signal drops, result value of the measure will change slow, causes of
turning on or off relay due to thresholds values. The critical situation is slowly
detected, so it is impossible to predict the relay state in that situations.
If parameter „AL” = „on”, the relay will be turned on in the critical situations,
even if his parameter “modE” = ”noAC”.
7.3.2. “inPt” menu
This menu presets the measurement input:
“tYPE" - type of the input / sensor. This parameter can be set to values:
”Pt 1”
- Pt-100 input,
”Pt 5”
- Pt-500 input,
”Pt10”
- Pt-1000 input.
”FiLt”
- this parameter sets filtration rate. It can be set to values from 0 (no filtration ) to 5
(strongest filtration – time window about 2 sec).
“toFS”
- offset (expressed in 0.1°C, range ± 9.9°C.). This parameter allows shifting of
measurement scale, and express value added to calculated (measured) result.
7.3.3. ”OutP” menu
This menu contains parameters of analogue output control. Menu is available if the
device is equipped witch analogue output.
i
Analogue output can be controlled depend on both present measured value and
peak value (if peak detection is enabled).
“Omod” - analogue output mode. Depending on version of the device there are following
options:
For active current output:
”oFF”
- current output disabled,
”0-20”
- current output enabled with 0 ÷ 20 mA mode,
“4-20”
- current output enabled with 4 ÷ 20 mA mode,
”modb” - current output controlled via RS-485 interface.
For passive current output:
”oFF”
- current output disabled,
“4-20”
- current output enabled with 4 ÷ 20 mA mode,
”modb” - current output controlled via RS-485 interface.
For active voltage output:
”oFF”
- voltage output disabled,
”0-5”
- voltage output enabled with 0 ÷ 5V mode,
”1-5”
- voltage output enabled with 1 ÷ 5V mode,
”0-10”
- voltage output enabled with 0 ÷ 10V mode,
“2-10”
- voltage output enabled with 2 ÷ 10 V mode,
”modb” - voltage output controlled via RS-485 interface.
27
User manual - METER SRT-N118
”OUtL”
- this parameter determines the input value for which the output signal is minimal
(depend of output mode „Omod”).
“OUtH”
- this parameter determines the input value for which the output signal is maximal
(depend of output mode „Omod”).
The analogue output value is calculated due to formula given below:
Out=
where:
i
W −" OUtL"
× B− A A
"OUtH" −"OUtL"
W – displayed value,
Out – analogue output value,
B – higher range limit (20mA / 5V / 10V),
A – lower range limit (0mA / 4mA / 0V / 1V / 2v),
“OutL” parameter can be greater than “OutH”. In this case the conversion
characteristic is reversed, it means that if input value raises the output value falls.
”Lo r”, ”Hi r”
- this parameters define the output value range. If calculated output value Out
exceeds defined range then analogue output generates signal equal to upper
or lower border of the defined range. These parameters defines the percentage
extension of nominal analogue range (with 0,1% resolution).
Parameter “Lo r” defines lower border of the range due to formula:
Outmin = A - (A × “Lo r” %), where:
A – lower signal value range limit.
This parameter can be set from 0 to 99.9% (for active current output and active
voltage output) or from 0 to 29.9% (for passive current output).
Parameter “Hi r” defines higher border of the range due to formula:
Outmax = B + (B × “Hi r” %), where:
B – higher signal value range limit.
This parameter can be set from 0 to 19.9% (for active and passive current
output) or from 0 to 9.9% (for active voltage output).
In example on page 34 of the DISPLAY VALUES CALCULATION paragraph
the procedure of the analogue outputs determining is presented in details.
“AL”
- this parameter determines the behaviour of analogue output if any critical situation
occurs. According to version of the device, this parameter can be set:
For active current output:
“noCH” - current will not change,
“22.1”
- current will be set to 22.1 mA,
“3.4”
- current will be set to 3.4 mA,
“0.0”
- current will be set to 0 mA.
28
User manual - METER SRT-N118
For passive current output:
“noCH” - current will not change,
“22.1”
- current will be set to 22.1 mA,
“3.4”
- current will be set to 3.4 mA,
For active voltage output:
“noCH” - voltage will not change,
“11.0”
- voltage will be set to 11 V,
“5.5”
- voltage will be set to 5.5 V,
“1.2”
- voltage will be set to 1.2 V.
“0.6”
- voltage will be set to 0.6 V,
“0.0”
- voltage will be set to 0 V.
When the critical situation goes, the output signal will be set to value calculated due to
formulas given above.
7.3.4. ”bri” parameter
This parameter allows user to set bright of the LED display, bright can be set to
conventional values from 1 to 8.
7.3.5. ”HOLd” menu
This menu contains parameters connected with peak detection function. See also full
description of the peak detection function in paragraph: DETECTION OF THE PEAK VALUES
“modE” - the type of detected changes of the input signal, can be set to values:
”norm”
”inv”
- peaks, peak and next drop of the input signal of value equal at least “PEA”,
- drops, drop and next peak of the input signal of value equal at least “PEA”,
“PEA”
- minimal detected signal change classified as peak or drop (see Figure 6.1)
“timE”
- maximum time of displaying of the peak (drop) value, can be set from 0.0 to 19.9
sec, with 0.1 sec. resolution. If „HdiS”=”HOLD” then setting parameter "timE"=0.0
causes holding peak value until [ESC] button is pressed. If „HdiS”=”rEAL” then
value "timE"=0.0 means no holding.
“HdiS”
- type of displayed values:
”rEAL”
”HOLd”
- current value is displayed,
- peak (drop) value is displayed,
“H r1”, “H r2” - relay/LED outputs ( R1, R2) operation mode:
”rEAL”
”HOLd”
”HOUt”
”rEAL”
”HOLd”
- relay/LED operates depend on the current value,
- relay/LED operates depend on the peak (drop) value.
- current output operation mode:
- current output operates depend on the current value,
- current output operates depend on the peak (drop) value.
29
User manual - METER SRT-N118
7.3.6. ”SECu” menu
This menu contains presets connected with availability of other parameters:
“Scod”
- user password (4-digits number). If this parameter is set at value “0000”, user
password is turned off.
If the user do not remember his password, the access to the menu is possible
by the “one-use password”. To get this password please contact with
Marketing Division. “Single use password” can be used only one time, after
that it is destroyed. Entering this password causes in clearing of user
password, it means sets the user password to „0000”.
i
The “one-use password” can be used ONE TIME ONLY, it is impossible to use it
again! The “one-use password” can be restored by Service Division only.
“A r1, A r2” - this option permits user (”on”) or prohibits (”oFF”) to modify the thresholds of
the relays/LEDs R1, R2 without knowledge about user password.
7.3.7. ”rS” menu
This menu is connected with RS-485 interface, and sets his properties:
”Addr”
- this parameter defines the address of the device, accordingly to Modbus protocol.
It can be set in range from 0 to 199. If the value 0 is set then device, responds to
frames with address 255 (FFh).
”bAud”
- this parameter determines RS-485 interface baud rate. It can be set to one of 8
possible values: ”1.2”, ”2.4”, ”4.8”, ”9.6”, ”19.2”, ”38.4”,”57.6”,”115.2”, which
respond to the baud rates of 1200, 2400, 4800, 9600, 19200, 38400, 57600 and
115200 bit/s respectively.
”mbAc” - this parameter sets the access to the configuration registers of the device.
Possible values:
”on”
- configuration registers can be set via RS-485 interface,
”oFF”
- configuration registers can not be set via RS-485 interface.
i
The access to registers no 04h i 05h cant be denied by ”mbAc” parameter (see:
LIST OF REGISTERS).
”mbtO”
- this parameter defines maximal time (sec) between following frames received by
the device. If the delay will be greater than the value of ”mbtO” parameter, the
relays and analogue outputs which are controlled via RS-485 interface, will set to
alert state (see "OUtP" menu, and “rEL1” menu description). Parameter “mbtO”
can be set to values from 0 to 99 seconds. The value 0 means that the time will be
not controlled.
”rESP”
- this parameter defines minimal (additional) delay between the Modbus message
and the answer of the device (received and sent via RS-485 interface). This
additional delay allows the device to work with poor RS-converters which do not
works properly on baud rates higher than 19200. This parameter can be set to one
of values:
30
User manual - METER SRT-N118
”Std”
” 10c”
” 20c”
” 50c”
”100c”
”200c”
i
- answer as quick as possible, no additional delay
- answer delayed of 10, 20, 50, 100 of 200 chars respectively, where
one character time depends on selected baud rate
In the most cases parameter ”rESP” should be set to ”Std” (no additional delay).
Unfortunately for some third party RS-converters ”rESP” should be adjusted
experimentally. Table 7.1 contains most frequently used values.
”bAud” parameter
“38.4”
“57.6”
“115.2”
”rESP” parameter
“ 10c”
“ 20c”
“ 50c”
Tab.7.1. Settings of ”rESP” parameter
7.3.8. ”Edit” parameter
This parameter allows to change the edition mode of numerical parameters:
”dig”
- the change to “by digit” mode,
”Slid”
- slide change mode.
7.3.9. ”dEFS” parameter
This setting allows to restore the factory settings of the device. To get the access to this
option special password is required: „5465”, next the device displays acknowledge question
„SEt?”. Press [ENTER] to acknowledge the restoring of factory settings or [ESC] to cancel.
7.3.10. ”SErv” menu
This menu contains the parameters for authorized service only. To enter this menu
proper service password must be entered. Improper settings can causes of damage of the
device.
31
User manual - METER SRT-N118
7.4. MENU STRUCTURE
Measurement mode
ESC
ESC
MENU
MENU
Press and hold at least 2 seconds
0___
4-digit user password entering (if it is different from „0000”)
ENTER
ESC
MENU
ENTER
rEL1
ENTER
SEtP
ENTER
ENTER
ESC
MENU
rEL2
ESC
MENU
Options similar
to „rEL1” menu
ESC
Parameter
edition
MENU
SEt2
HYSt
ESC
MENU
modE
t on
toFF
unit
AL
ENTER
ESC
MENU
inPt
ENTER
tYPE
ENTER
ESC
MENU
FiLt
toFS
ENTER
ESC
MENU
ENTER
Omod
OUtP
ENTER
ESC
Parameter
edition
MENU
OUtL
OUtH
ESC
MENU
ENTER
ESC
MENU
bri
ENTER
ESC
MENU
Parameter
edition
Lo r
Hi r
AL
option
See next page
32
ESC
MENU
Parameter
edition
User manual - METER SRT-N118
See previous page
ENTER
ESC
MENU
ENTER
modE
HOLd
ENTER
ESC
Parameter
edition
MENU
PEA
timE
ESC
MENU
Hdis
H r1
H r2
HOut
option
ESC
MENU
ENTER
SECU
ENTER
Scod
ENTER
ESC
MENU
ESC
Parameter
edition
MENU
A r1
A r2
ENTER
ESC
MENU
ENTER
Addr
rS
ENTER
ESC
Parameter
edition
MENU
bAud
ESC
MENU
mbAc
mbtO
ENTER
ESC
MENU
Edit
ESC
MENU
Parameter
edition
rESP
4-digit special
password entering
ENTER
ESC
MENU
ENTER
0___
dEFS
MENU
ENTER
SEt?
ESC
Default settings
restoring
ESC
MENU
ESC
MENU
SErv
33
User manual - METER SRT-N118
8. THE ALARM LED
Alarm LED (AL) lights in cases:
• exceeding of permissible measurement range
• detection of sensor malfunction (shortcut or break of measurement circuit)
9. ANALOGUE OUTPUT VALUE CALCULATION
Lets assume that we have active current output and its parameters are:
“modE” = “4-20”, “OUtL” = 100, “OUtH” = 200, “Lo r” = 5.0, “Hi r” = 5.0
Parameters “Lo r” and “Hi r” define working range of current output to 3.8 ÷ 21 mA.
Output current will be calculated for three displayed values „D”:
a) D = „17.5”
According to formula from page 28:
Iout = (17.5-10.0) / (20.0-10.0) × 16 mA + 4 mA = 0.75 ·16 + 4 = 16 mA
Calculated Iout do not exceeds the output working range (3.8 - 21 mA).
b) D = „20.5”
According to formula from page 28:
Iout = (20.5-10.0) / (20.0-10.0) × 16 mA + 4 mA = 1.05 ·16 + 4 = 20.08 mA
Calculated Iout do not exceeds the output working range (3.8 - 21 mA).
c) D = „30.0”
According to formula from page 28:
Iout = (30.0-10.0) / (20.0-10.0) × 16 mA + 4 mA = 2 ·16 + 4 = 36 mA.
Calculated Iout exceeds the output working range (3 - 21 mA), so current output will generate
current equal to the upper border of range defined by parameter “Lo r” and “Hi r” (it means
21 mA).
10. THE MODBUS PROTOCOL HANDLING
Transmission parameters: 1 start bit, 8 data bits, 1 or 2 stop bit (2 bits are send, 1 and 2 bits
are accepted when receive), no parity control
Baud rate:
selectable from: 1200 to 115200 bits/second
Transmission protocol:
MODBUS RTU compatible
The device parameters and display value are available via RS-485 interface, as HOLDINGtype registers (numeric values are given in U2 code) of Modbus RTU protocol. The registers
(or groups of the registers) can be read by 03h function, and wrote by 06h (single registers) or
10h (group of the registers) accordingly to Modbus RTU specification. Maximum group size for
03h and 10h functions can not exceeds 16 registers (for single frame).
i
The device interprets the broadcast messages, but then do not sends the answers.
10.1. LIST OF REGISTERS
34
User manual - METER SRT-N118
Register
Write
Range
01h
No
-999 ÷ 6000
02h
No
The status of the current measurement; 0h - data valid; A0h - top
0h, A0h, 60h border of the measurement range is exceeded; 60h - bottom border
of the measurement range is exceeded;
03h
No
04h
05h1
1
Register description
Measurement value (no decimal point)
Decimal point position, constant value: 1 - “ 0.0”;
State of the relays and alarm LED (binary format)
(1 - on, 0 - off): 00000000 000e00ba
a - relay R1; b - relay R2; e - alarm LED;
If written, only a, b bits are important (others are ignored) these bits
allows user to control the relays via RS-485 interface
Yes
see descr.
Yes
0h ÷ 1800h
Yes
State of passive current output, expressed in 1/256 mA units – it
2CCh÷1800h means that high byte express integer part, and low byte fractional
part of desired output current.
Yes
0h ÷ 1600h
State of active current output, expressed in 1/256 mA units – it
means that high byte express integer part, and low byte fractional
part of desired output current.
State of active voltage output, expressed in 1/512 V units – it means
that high byte express integer part, and low byte fractional part of
desired output voltage.
06h
No
-999 ÷ 6000 Peak (drop) value (no decimal point)
10h
Yes
0÷2
“tyPE” parameter in “InPt” menu (input type).
0 - Pt-100; 1 - Pt-500; 2 - Pt-1000
12h
Yes
0÷5
“FiLt” parameter in “InPt” menu (measurement filtering rate)
18h
Yes
-99 ÷ 99
“toFS” parameter in “InPt” menu (shift of measurement scale),
expressed by 0,1°C
20h2
Yes
0 ÷ 199
Device address
21h
No
21B0h
Device identification code (ID)
22h3
Yes
0÷7
“bAud” parameter in “rS” menu (baud rate);
0 - 1200 baud; 1 - 2400 baud; 2 - 4800 baud; 3 - 9600 baud;
4 - 19200 baud; 5 - 38400 baud; 6 - 57600 baud; 7 - 115200 baud
23h4
Yes
0÷1
“mbAc” parameter in “rS” menu (permission to write registers via
RS-485 interface); 0 - write denied ; 1 - write allowed
24h
Yes
see descr.
25h
Yes
0÷5
“rESP” parameter in “rS” menu (additional response delay);
0 - no additional delay; 1 - ”10c” option; 2 - ”20c” option;
3 - ”50c” option; 4 - ”100c” option; 5 - ”200c” option;
27h
Yes
0 ÷ 99
“mbtO” parameter in “rS” menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
2Dh
Yes
1÷8
“bri” parameter (display brightness);
1 - the lowest brightness; 8 - the highest brightness
Parameters of “SECU” menu (binary format (0 - „oFF”, 1 - „on”):
bit 0 - “A r1” parameter; bit 1 - “A r2” parameter
35
User manual - METER SRT-N118
Register
Write
Range
2Fh
Yes
0÷1
30h
Yes
-999 ÷ 9999
“SEtP” parameter in “rEL1” menu, no decimal point included
31h
Yes
-999 ÷ 999
“HySt” parameter in “rEL1” menu, no decimal point included
32h
Yes
0÷5
33h
Yes
0 ÷ 999
“t on” parameter in “rEL1” menu, expressed in tenth of seconds or
tenth of minutes depend on “unit” parameter - register no. 35h)
34h
Yes
0 ÷ 999
“toFF” parameter in “rEL1” menu, expressed in tenth of seconds
or tenth of minutes depend on “unit” parameter - register no. 35h)
35h
Yes
0÷1
“unit” parameter in “rEL1” menu:
0 - seconds; 1 - minutes
36h
Yes
0÷2
“AL” parameter in “rEL1” menu: 0 - no changes; 1 - on; 2 - off
37h
Yes
-999 ÷ 9999
“SEt2” parameter in “rEL1” menu, no decimal point included
38h
Yes
-999 ÷ 9999
“SEtP” parameter in “rEL2” menu, no decimal point included
39h
Yes
-999 ÷ 999
“HySt” parameter in “rEL2” menu, no decimal point included
3Ah
Yes
0÷5
3Bh
Yes
0 ÷ 999
“t on” parameter in “rEL2” menu, expressed in tenth of seconds or
tenth of minutes depend on “unit” parameter - register no. 3Dh)
3Ch
Yes
0 ÷ 999
“toFF” parameter in “rEL2” menu, expressed in tenth of seconds
or tenth of minutes depend on “unit” parameter - register no. 3Dh)
3Dh
Yes
0÷1
“unit” parameter in “rEL2” menu:
0 - seconds; 1 - minutes
3Eh
Yes
0÷2
“AL” parameter in “rEL2” menu: 0 - no changes; 1 - on; 2 - off
3Fh
Yes
-999 ÷ 9999
50h
Yes
0÷1
51h
Yes
0 ÷ 9999
“PEA” parameter in “HOLd” menu (minimum detectable change, no
decimal point included)
52h
Yes
0 ÷ 199
“timE” parameter in “HOLd” menu, maximum peaks' (or drops')
display time expressed in seconds
53h
Yes
0÷1
“HdiS” parameter in “HOLd” menu:
0 - “rEAL” mode ; 1 - “HOLd” mode
54h
Yes
0÷1
“H r1” parameter in “HOLd” menu :
0 - “rEAL” mode ; 1 - “HOLd” mode
55h
Yes
0÷1
“H r2” parameter in “HOLd” menu:
0 - “rEAL” mode ; 1 - “HOLd” mode
36
Register description
“Edit” parameter (numerical parameters edit mode);
0 - „dig” mode; 1 - „SLid” mode
“modE” parameter in “rEL1” menu:
0 - “noAC” mode; 1 - “on” mode; 2 - “oFF” mode; 3 - “in” mode;
4 - “out” mode; 5 - “modb” mode
“modE” parameter in “rEL2” menu:
0 - “noAC” mode; 1 - “on” mode; 2 - “oFF” mode; 3 - “in” mode;
4 - “out” mode; 5 - “modb” mode
“SEt2” parameter in “rEL2” menu, no decimal point included
“modE” parameter in “HOLd” menu (type of detected changes):
0 - peaks; 1 - drops
User manual - METER SRT-N118
Register
Write
Range
58h1
Yes
0÷1
“HOUt” parameter in “HOLd” menu:
0 - “rEAL” mode ; 1 - “HOLd” mode
Yes
0÷3
“Omod” parameter in “OUtP” menu (active current output mode)
0 - current output disabled; 1 - current output enabled with 4÷20mA
mode; 2 - current output enabled with 0÷20mA mode;
3 - current output controlled via RS-485 interface
Yes
0÷2
“Omod” parameter in “OUtP” menu (passive current output mode)
0 - current output disabled; 1 - current output enabled with 4÷20mA
mode; 2 - current output controlled via RS-485 interface
Yes
0÷5
“Omod” parameter in “OUtP” menu (active voltege output mode)
0 - voltage output disabled; 1 - voltage output enabled with 0÷5V
mode; 2 - voltage output enabled with 1÷5V mode; 3 - voltage
output enabled with 0÷10V mode; 4 - voltage output enabled with
2÷10V mode; 5 - voltage output controlled via RS-485 interface
A1h1
Yes
-999 ÷ 9999
“OUtL” parameter in “OUtP” menu, no decimal point included
A2h
1
Yes
-999 ÷ 9999
“OUtH” parameter in “OUtP” menu, no decimal point included
Yes
0 ÷ 999
A3h
1
“Lo r” parameter in “OUtP” menu, for active current output and
active voltage output, expressed in 0.1%
Yes
0 ÷ 299
“Lo r” parameter in “OUtP” menu for passive current output,
expressed in 0.1%
Yes
0 ÷ 199
“Hi r” parameter in “OUtP” menu for active and passive current
output, expressed in 0.1%
Yes
0 ÷ 99
“Hi r” parameter in “OUtP” menu for active voltage output,
expressed in 0.1%
Yes
0÷3
“AL” parameter in “OUtP” menu (active current output value on
critical exception): 0 - no change; 1 - 22.1 mA; 2 - 3.4 mA; 3 - 0 mA
Yes
0÷2
“AL” parameter in “OUtP” menu (passive current output value on
critical exception): 0 - no change; 1 - 22.1 mA; 2 - 3.4 mA
Yes
0÷5
A0h1
A4h
1
A5h1
Register description
“AL” parameter in “OUtP” menu (active voltage output value on
critical exception): 0 - no change; 1 - 11 V; 2 - 5.5; 3 - 1.2 V;
4 - 0.6 V; 5 - 0 V
1
2
3
4
- these registers are active only if device is equipped with current or voltage output.
- after writing to register no 20h the device responds with an “old” address in the message.
- after writing to register no 22h the device responds with the new baud rate.
- the value of the “mbAc” parameter is also connected to write to this register, so it is possible to block a writes, but
impossible to unblock writes via RS-485 interface, The unblocking of the writes is possible from menu level only.
37
User manual - METER SRT-N118
10.2. TRANSMISSION ERRORS DESCRIPTION
If an error occurs while write or read of single register, then the device sends an error
code according to Modbus RTU specifications (example message no 1).
Error codes:
01h - illegal function (only functions 03h, 06h and 10h are available),
02h - illegal register address
03h - illegal data value
08h - no write permission ( see: “mbAc” parameter)
A0h - exceed of upper border of input range
60h - exceed of lower border of input range
A0h and 60h codes can appear only during reg. 01h is reading by 03h function (read of
a single register).
10.3. EXAMPLES OF QUERY/ANSWER FRAMES
Examples apply for device with address 1. All values are represent hexadecimal.
Field description:
ADDR
Device address on modbus network
FUNC
Function code
REG H,L
Starting address (address of first register to read/write, Hi and Lo byte)
COUNT H,L
No. of registers to read/write (Hi and Lo byte)
BYTE C
Data byte count in answer frame
DATA H,L
Data byte (Hi and Lo byte)
CRC L,H
CRC error check (Hi and Lo byte)
1. Read of the displayed value (measurement), SRT-N118 device address = 01h:
ADDR
FUNC
01
03
REG H,L
00
01
COUNT H,L
00
01
CRC L,H
D5
CA
a) The answer (we assume that the measure result is not out of range):
ADDR
FUNC
BYTE C
01
03
02
DATA H,L
00
FF
CRC L,H
F8
04
DATA H, L - displayed value = 255, no decimal point.
Decimal point position can be read from reg. 03h.
38
User manual - METER SRT-N118
b) The answer (if an error occur):
ADDR FUNC
01
ERROR
83
CRC L,H
60
41
18
ERROR - error code = 60h, bottom border of the measurement range is exceeded
2. Read of device ID code
ADDR
FUNC
REG H,L
01
03
00
ADDR
FUNC
BYTE C
01
03
02
COUNT H,L
21
00
CRC L,H
01
D4
00
The answer:
DATA H,L
21
CRC L,H
B0
A1
A0
DATA - identification code (21B0h)
3. Change of the device address from 1 to 2 (write to reg. 20h)
ADDR
FUNC
01
06
REG H,L
00
20
DATA H,L
00
02
CRC L,H
09
C1
DATA H - 0
DATA L - new device address (2)
The answer (the same as the message):
ADDR
FUNC
01
06
REG H,L
00
20
DATA H,L
00
02
CRC L,H
09
C1
4. Change of baud rate of all devices connected to the net (BROADCAST message).
ADDR
FUNC
00
06
REG H,L
00
22
COUNT H,L
00
04
CRC L,H
29
D2
DATA H - 0
DATA L - 4, new baud rate 19200 baud
i
Device do not reply to BROADCAST-type messages.
39
User manual - METER SRT-N118
5. Read of the registers 1, 2 and 3 in one message (example of reading a number of
registries in one frame):
ADDR
FUNC
01
03
REG H,L
00
COUNT L
COUNT H,L
01
00
03
CRC L,H
54
0B
- the count of being read registers (max.16)
The answer:
ADDR
FUNC
01
03
DATA H1, L1
DATA H2, L2
DATA H3, L3
i
40
BYTE C DATA H1,L1
06
00
0A
DATA H2,L2
00
00
DATA H3,L3
00
01
CRC L,H
78
B4
- reg. 01h (10 - displayed value ”1.0”),
- reg. 02h (0 - no errors),,
- reg. 03h (1 - decimal point position ” 0.0”).
There is no full implementation of the Modbus Protocol in the device. The
functions presented above are available only.
User manual - METER SRT-N118
11. DEFAULT AND USER'S SETTINGS LIST
Parameter
Description
Default value
User's value
Desc.
page
Parameters of relay R1 operation (“rEL1” menu)
SEtP
Relay R1 threshold
20.0
25
SEt2
Relay R1 second threshold
40.0
25
HYSt
Hysteresis of relay R1
0.0
25
modE
Operation mode of relay R1
on
25
t on
Turn on delay of relay R1
0.0
26
toFF
Turn off delay of relay R1
0.0
26
unit
Unit of “t on”, “toFF” parameters of relay R1
SEC
26
AL
Reaction for critical situation of relay R1
oFF
26
SEtP
Relay R2 threshold
40.0
25
SEt2
Relay R2 second threshold
60.0
25
HYSt
Hysteresis of relay R2
0.0
25
modE
Operation mode of relay R2
on
25
t on
Turn on delay of relay R2
0.0
26
toFF
Turn off delay of relay R2
0.0
26
unit
Unit of “t on”, “toFF” parameters of relay R2
SEC
26
AL
Reaction for critical situation of relay R2
oFF
26
tYPE
Input type
FiLt
Filtering ratio
toFS
Shifting of measurement scale
Parameters of relay R2 operation (“rEL2” menu)
Configuration of measurement input (“inPt” menu)
„Pt 1”
27
0
27
0.0
27
Active current output configuration (“OUtP” menu)
Omod
Active current output mode
„0-20” (mA)
27
OUtL
Display value for 0 mA or 4 mA current output
0.0
28
OUtH
Display value for 20 mA current output
Lo r
Extension of the bottom of the nominal output
range
100.0
28
5.0 (%)
Hi r
Extension of the top of the nominal output range
5.0 (%)
28
AL
Current output value on critical exception
22.1 (mA)
28
28
Passive current output configuration (“OUtP” menu)
Omod
Passive current output mode
„4-20” (mA)
27
41
User manual - METER SRT-N118
Parameter
Description
Default value
User's value
Desc.
page
OUtL
Display value for 4 mA current output
0.0
28
OUtH
Display value for 20 mA current output
100.0
28
Lo r
Extension of the bottom of the nominal output
range
Hi r
Extension of the top of the nominal output range
AL
Current output value on critical exception
5.0 (%)
28
5.0 (%)
28
22.1 (mA)
28
Active voltage output configuration (“OUtP” menu)
Omod
Active voltage output mode
„0-10” (V)
27
OUtL
Display value for 0 V, 1 V or 2 V voltage output
OUtH
Display value for 5 V or 10 V voltage output
0.0
28
100.0
28
Lo r
Extension of the bottom of the nominal output
range
Hi r
Extension of the top of the nominal output range
5.0 (%)
28
AL
Voltage output value on critical exception
11.0 (V)
28
bri6
29
5.0 (%)
28
Display parameters
bri
Display brightness
Configuration of peaks detection function (“HOLd” menu)
modE
Kind of detected changes
norm
29
PEA
Minimum detected change
0.0
29
timE
Maximum time of peak displaying
0.0
29
HdiS
The type of displayed value
HOLd
29
H r1
Source of relay R1, and LED R1 control
rEAL
29
H r2
Source of relay R2, and LED R2 control
rEAL
29
HOut
Source of current output control
rEAL
29
A r1
Permission to changes of relay R1 threshold
without of the user password knowledge
on
A r2
Permission to changes of relay R2 threshold
without of the user password knowledge
on
Settings of access to the configuration parameters (“SECu” menu)
30
30
RS 485 interface configuration (menu “rS”)
Addr
Device address
0
30
bAud
Baud rate
9.6
30
mbAc
Permission to changes of configuration registers
on
30
mbtO
Maximum delay between received messages
0
30
rESP
Additional delay of answer transmission
Std
30
42
User manual - METER SRT-N118
Parameter
Description
Default value
User's value
Desc.
page
Configuration of numerical parameters edition
Edit
Numerical parameters edit mode
dig
31
43
SIMEX Sp. z o.o.
ul. Wielopole 11
80-556 Gdańsk
Poland
tel.: (+48 58) 762-07-77
fax: (+48 58) 762-07-70
http://www.simex.pl
e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement