SAP PDL Driver User Manual - Technical Support Request

Device Driver for SATO Printers
- Version 1.0.8
SAP Device Driver for SATO Printers
User Manual
1-50
Software License Agreement
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS
BEFORE USING THIS PRODUCT. BY INSTALLING THE
PRODUCT YOU THEREBY INDICATE YOUR ACCEPTANCE OF
THESE TERMS AND CONDITIONS. SHOULD YOU DISAGREE
WITH ANY OF THE TERMS OR CONDITIONS LISTED BELOW,
PROMPTLY REMOVE ALL FILES RELATED TO THIS PRODUCT
FROM YOUR HOST PLATFORM AND RETURN THE PRODUCT
TO SATO CORPORATION.
9.
SATO Corporation warrants that for ninety (90) days after
delivery, the Software will perform in accordance with
specifications published by SATO Corporation, and that the
distribution media will be free from defects in material and
workmanship. SATO Corporation does not warrant that the
Software is free from all bugs, errors and omissions.
10.
Your exclusive remedy and the sole liability of SATO
Corporation in connection with the Software is replacement
1.
You explicitly agree to accept a non-exclusive license to use
of defective distribution media upon their return to SATO
the Software identified on the distribution media solely for your
Corporation. SATO Corporation will not be liable for any loss
own customary business or personal purposes. Your local
or damage caused by delays in furnishing a Software Product
and national laws govern this Agreement.
2.
or any other performance under this Agreement.
Henceforth, “Software” shall refer to the digitally encoded,
SATO Corporation does not warrant that the functions contained in
machine-readable data and program. The term “Software
the Software will meet your requirements or that the operation of
Product” includes the Software identified on the distribution
the Software will be uninterrupted or error free.
media, including any accompanying documentation. The
term “Distribution Media” refers to any method by which the
3.
4.
not limited to Floppy Disks, CD-ROM, Magnetic Tape and
country, such as the Rights in Technical Data and Computer
On-Line distribution via the Internet. The Software Product is
licensed (not sold) to you, and SATO® either owns or
Software clause at FAR 242.227- 7013, subdivision (b) (3) (ii)
licenses from other vendors who own all copyright, trade
duplication or disclosure is subject to restrictions applicable to
secret, patent and other proprietary rights in the Software
restricted rights software as set forth in FAR 52.227-19 (c) (2)
Product.
or equivalent rules.
or subparagraph (c) (1) (ii), as appropriate. Further use,
To protect the proprietary rights of SATO Corporation, you
agree to maintain the Software Product and other proprietary
THE PARTIES AGREE THAT ALL OTHER WARRANTIES,
information concerning the Software Product in strict
EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
confidence and to establish reasonable procedures regulating
FITNESS FOR A PARTICULAR PURPOSE AND
access to and use of the software.
MERCHANTABILITY ARE EXCLUDED.
You agree not to duplicate or copy the Software except that you
SATO Corporation reserves the right to make changes and/or
may make one backup copy. You agree that any such copy
improvements in the Software without notice at any time.
on the original.
6.
Use, duplication or disclosure by the Government is subject
to restrictions as set forth in the relevant guidelines of your
shall contain the same proprietary notices as those appearing
5.
11.
Software Product is delivered to the end user, including but
IN NO EVENT WILL SATO CORPORATION BE LIABLE FOR
LOST PROFITS, LOST DATA, BUSINESS INTERRUPTIONS
You shall not sub-license, sell, lease, or otherwise transfer all
OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL OR
or any portion of the Software Product separate from the
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
printer(s), without the prior written consent of SATO
OF OR INABILITY TO USE THIS PRODUCT, EVEN IF SATO
Corporation.
CORPORATION HAS BEEN ADVISED OF THE POSSIBILITY
You may not modify or prepare derivative works of the
OF SUCH DAMAGES, OR ANY DAMAGES CAUSED BY
Software Product. You may not transmit the Software
ABUSE OR MANIPULATION OF THE SOFTWARE. SOME
Product over a network, by telephone, or electronically
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
using any means; or reverse engineer, decompile or
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
disassemble the Software.
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU.
7.
You may transfer the Software Product with the printer(s), but
only if the recipient agrees to accept the terms and conditions
of this Agreement. Your license is automatically terminated if
you transfer the Software Product and printer(s).
8.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS
AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND
BY ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE
This License remains in force until terminated, and may be
BOUND BY ANY STATEMENT OR REPRESENTATION NOT
terminated by agreement between you and SATO
CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS
Corporation, or by SATO Corporation, if you fail to comply with
AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED
the terms of this License if such failure is not corrected within
BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH
thirty (30) days after notice. When this License is terminated,
PARTY. BY INSTALLING THIS SOFTWARE PRODUCT, YOU
you shall either return to the place you obtained them from, or
AGREE TO ACCEPT THE TERMS AND-CONDITIONS OF THIS
destroy, the printer and all copies of the Software and
AGREEMENT.
documentation.
SAP Device Driver for SATO Printers
User Manual
2-50
Copyrights
The contents of this document are proprietary information of SATO Corporation and/or its
subsidiaries in Japan, the U.S and other countries. No part of this document may be
reproduced, copied, translated or incorporated in any other material in any form or by any
means, whether manual, graphic, electronic, mechanical or otherwise, without the prior
written consent of SATO Corporation.
SATO Corporation and/or its subsidiaries in Japan, the U.S and other countries make no
representations or warranties of any kind regarding this material, including, but not limited
to, implied warranties of merchantability and fitness for a particular purpose. SATO
Corporation shall not be held responsible for errors contained herein or any omissions
from this material or for any damages, whether direct, indirect, incidental or consequential,
in connection with the furnishing, distribution, performance or use of this material.
SATO Corporation reserves the right to make changes and/or improvements in this
product and document without notice at any time.
Trademarks
SATO is a registered trademark of SATO Corporation and/or its subsidiaries in Japan, the U.S
and other countries.
SAP® is the registered trademark of SAP AG in Germany and in several other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other brands and their products are trademarks or registered trademark of their respective
holders and should be noted as such.
Software updating disclaimer
While all efforts have been taken to ensure accuracy and currency of the information
contained herein, there are instances where the contents of this document may be
outdated. In that case, proceed to SATO worldwide websites (www.satoworldwide.com)
to check whether an updated document has been made available for your reference.
Alternatively, you can consult your nearest authorized SATO technical representative, as
listed on the back cover, to obtain the relevant information about SAP Device Printer
Driver Software.
Version 1.0.8
© 2009 SATO Corporation. All rights reserved.
SAP Device Driver for SATO Printers
User Manual
3-50
Table of Contents
Table of Contents.............................................................................................. 4
1
Introduction................................................................................................. 5
2
SAP Environment ....................................................................................... 6
3
Overview of Solution.................................................................................. 7
4
Using SATO Device Type .......................................................................... 8
5
Creating Output Device ........................................................................... 13
6
Functionalities of SATO-SAP Printer Driver.......................................... 15
6.1
6.2
6.3
6.4
6.5
Barcode ............................................................................................ 15
6.1.1 Defining Barcode
16
6.1.2 New Barcode Technology
17
6.1.3 New Technology Barcode
20
6.1.4 Old Barcode Technology (Conventional System Barcode) 22
6.1.5 Old Technology Barcode
22
6.1.6 Defining Printer Barcodes
23
Fonts................................................................................................. 26
SmartStyles ...................................................................................... 28
Smart Forms ..................................................................................... 30
6.4.1 Adding Text
31
6.4.2 Adding Barcode
33
6.4.3 Adding Images
34
6.4.4 Positioning Printing Components
35
6.4.5 Printing the Smart Forms
35
System Commands .......................................................................... 37
6.5.1 Text and Image Rotation
41
7
Limitations ................................................................................................ 42
8
Appendix ................................................................................................... 43
8.1
8.2
Print Controls List for Barcode.......................................................... 43
Font Print Controls............................................................................ 49
SAP Device Driver for SATO Printers
User Manual
4-50
Introduction
1
“SAP Device Driver for SATO printers” is a SAP Smart Forms printing solution to SATO
printer. It allows users to use a driver for a Page Description Language (PDL) that is
implemented in ABAP and resided in the SAP environment to print SATO printer without 3rd
party solutions. With this device driver, SATO BASIC PROGRAMMING LANGUAGE or
SBPL is sent to the SATO printer directly from SAP –- providing greater performance and
efficiency.
This document explains the necessary environment and configuration to use such a
solution.
SAP Device Driver for SATO Printers
User Manual
5-50
SAP Environment
2
The following SAP environment supports the ABAP based PDL drivers:
•
SAP_BASIS Release 6.20:
Support Package SAPKB62064 + attached correction instructions or
Support Package SAPKB62065 + attached correction instructions
or Support Package SAPKB62066
Kernel 6.40 patch level 222
•
SAP_BASIS Release 6.40:
Support Package SAPKB64022 + attached correction instruction
or Support Package SAPKB64023
Kernel 6.40 patch level 222
•
SAP_BASIS Release 7.00:
Support Package SAPKB70014 + attached correction instruction
or Support Package SAPKB70016
Kernel 7.00 patch level 148
•
SAP_BASIS Release 7.01:
supported from the beginning
•
SAP_BASIS Release 7.10:
not supported in 7.10
Please refer to the SAP Notes: 1097563 for the updated information about the overview of
SAP PDL driver.
SAP Device Driver for SATO Printers
User Manual
6-50
Overview of
Solution
3
This solution is primarily for Smart Forms printing. It requires 2 components from the printer
providers, such as SATO.
- ABAP Based PDL device driver
- Device Type files
After uploading the components into the SAP system, users will
- Use Smart Styles to define the available printing items in the device type,
- Use Smart Forms to design the label
- Define Output Device that points to the given Device Type
- Print the Smart Forms through the output device.
SATO ABAP BASED PDL
Device Driver
SATO Device Type Files
SAP Spool Service
SATO Printers
Figure 1 Overview of solution
Please refer to the SAP Notes: 1135106 for the updated information about the SATO PDL
Driver.
SAP Device Driver for SATO Printers
User Manual
7-50
4
Using SATO
Device Type
The following device types for SATO PDL Driver are available:
Codepage
Name of Device Type
Resolution
Latin1 (ISO8859-1)
YSTLTGT2
203dpi
English Only
(7-Bit USA ASCII
Ausgabe)
Europe Characters
(Codepage 850)
Supported models
GT408e
S8408
LT408
MB400i
YSTLTGT3
305dpi
GT412e
S8412
MB410i
YSTLTGT6
609dpi
GT424e
S8424
YSTLTGL2
203dpi
GL408e
YSTLTGL3
305dpi
GL412e
* YSTLTSR2
203dpi
SR408
PT408e
MR400e
* YSTLTSR3
305dpi
SR412
PT412e
MR410e
* YSTLTSR6
609dpi
SR424
YSTENGT2
203dpi
GT408e
S8408
LT408
YSTENGT3
305dpi
GT412e
S8412
YSTENGT6
609dpi
YSTENGL2
YSTENGL3
* YSTENSR2
203dpi
305dpi
203dpi
* YSTENSR3
305dpi
* YSTENSR6
609dpi
GT424e
S8424
GL408e
GL412e
SR408
MR400e
SR412
MR410
SR424
YSTCPCL2
203dpi
SAP Device Driver for SATO Printers
User Manual
CL408e
CL608e
CT408i
M-8459Se
8-50
M-8485Se
M-8460Se
M84-Pro2
CG208
YSTCPCL3
305dpi
CL412e
CL612e
CT412i
M-8465Se
M-8490Se
M10e
M84-Pro3
CG212
YSTCPCL6
609dpi
M84-Pro6
YSTKOGT2
203dpi
GT408e
YSTKOGT3
305dpi
GT412e
YSTKOGT6
609dpi
GT424e
YSTKOGL2
203dpi
GL408e
YSTKOGL3
305dpi
GL412e
YSTKUGL2
203dpi
GL408e
YSTKUGL3
305dpi
GL412e
YSTZFGT2
203dpi
GT408e
YSTZFGT3
305dpi
GT412e
YSTZFGT6
YSTZFGL2
609dpi
203dpi
GT424e
GL408e
YSTZFGL3
305dpi
GL412e
Traditional Chinese
Unicode (UTF-8)
YSTFUGL2
YSTFUGL3
203dpi
305dpi
GL408e
GL412e
Simplified Chinese
(GB2312)
YSTZHGT2
203dpi
GT408e
YSTZHGT3
305dpi
GT412e
YSTZHGT6
609dpi
GT424e
YSTHUGL2
203dpi
GL408e
YSTHUGL3
305dpi
GL412e
YSTJAPT2
YSTJAPT2
YSTJASR2
YSTJASR3
YSTJASR6
203dpi
305dpi
203dpi
305dpi
609dpi
*PT408e
*PT412e
*SR408
*SR412
*SR424
Korean
(Wansung Encoding,
HYRGothic-Medium)
Korean Unicode
(UTF-8)
Traditional Chinese
(Big5)
Simplified Chinese
Unicode (UTF-8)
Japanese (Shift-JIS)
Table 1 Device Types
Note: * denotes Japanese models
SAP Device Driver for SATO Printers
User Manual
9-50
Printer Model
CL4xxe/CL6xxe
Supported Languages
European Characters (codepage 850)
Device Type
YSTCPCLx
GL4xxe
Latin1 (ISO8859-1)
English (ASCII characters)
Korean (Wansung Encoding / Unicode)
YSTLTGLx
YSTENGLx
YSTKOGLx / YSTKUGLx
Simplified Chinese (Unicode)
Traditional Chinese (Big5 / Unicode)
YSTHUGLx
YSTZFGLx / YSTFUGLx
Latin1 (ISO8859-1)
English (ASCII characters)
Korean (Wansung Encoding)
Simplified Chinese (GB2312)
Traditional Chinese (Big5)
Latin1 (ISO8859-1)
English (ASCII characters)
Latin1 (ISO8859-1)
YSTLTGTx
YSTENGTx
YSTKOGTx
YSTZHGTx
YSTZFGTx
YSTLTGTx
YSTENGTx
YSTLTGTx
English (ASCII characters)
YSTENGTx
MB4xxi
Latin1 (ISO8859-1)
English (ASCII characters)
YSTLTGTx
YSTENGTx
M84xxSE
European Characters (codepage 850)
YSTCPCLx
M84-Pro
European Characters (codepage 850)
YSTCPCLx
M10e
European Characters (codepage 850)
YSTCPCLx
CT4xxi
European Characters (codepage 850)
YSTCPCLx
CG2xx
European Characters (codepage 850)
YSTCPCLx
* SR4xx
Latin1 (ISO8859-1)
English (ASCII characters)
Japanese (Shift-JIS)
Latin1 (ISO8859-1)
English (ASCII characters)
Latin1 (ISO8859-1)
Japanese (Shift-JIS)
YSTLTSRx
YSTENSRx
YSTJASRx
YSTLTSRx
YSTENSRx
YSTLTSRx
YSTJASRx
GT4xxe
S84xx
LT408
* MR4xx
* PT4xxe
Table 2 Supported Languages of Device Types
Note: * denotes Japanese models
The following printer models support RFID Gen2 Barcode printing with SATO PDL Driver:
- CL4/6xxe
- GL4xxe
- GT4xxe/SR4xx
- M84xxSE
- S-84xx
* Ultra-High-Frequency (UHF) are used for the RFID encoding for the above printer models.
SAP Device Driver for SATO Printers
User Manual
10-50
To print Asian languages from GT/SR or GL printer, language memory cartridge is needed:
Language Pack
Part Number
GT Korean Memory Cartridge
WWGT0590C
GT Simplified and Traditional Cartridge
WWGT0590K
GL Simplified Chinese Memory Cartridge
WWGL159BC
GL Traditional Chinese Memory Cartridge
WWGL159DC
GL Korean Memory Cartridge
WWGL159FK
SR Japanese Cartridge
WSR401910
Table 3 Memory Cartridge and Part No.
Note: Before uploading the device type files, the SATO Device Driver (PDL Driver) object has to
be imported to the SAP System. The object file is to be imported using STMS (Transport
Management System) Transaction.
The instruction of importing the PDL Device Driver can be found in the SAP Wizard Note: Note
1103422 - SAP Printer Vendor program: Installing device types, etc.
The SATO Device Type has to be uploaded into the SAP system by using the program
‘RSTXSCRP’ in the transaction code ‘se38’.
Figure 2 Uploading SATO Device Type
SAP Device Driver for SATO Printers
User Manual
11-50
Click ‘F8’ to execute the command. The following screen will be displayed:
Figure 3 Importing Device Type file
Click on the radio button on ‘Device Type’. Change the Mode (EXPORT/IMPORT) to ‘IMPORT’.
Then key in a name to represent the Device Type.
Note: The name must start with ‘YST’. It should contain 8 characters. The object name must
match with the file name of the device type (without the extension).
Click the Execute button (F8) to continue.
Figure 4 Selecting device type file
SAP Device Driver for SATO Printers
User Manual
12-50
Creating Output
Device
5
Enter ‘SPAD’ transaction code to go to the Spool Administration application.
Figure 5 Creating Output Device
Under the Devices/Servers tab, click on “Display” button for ‘Output Devices’.
Figure 6 Click on the 'Edit' button to change the Edit mode
Figure 7 Edit Mode buttons
Click on the ‘Create’ button to create a new Output Device.
SAP Device Driver for SATO Printers
User Manual
13-50
Figure 8 Defining Output Device
Enter a meaningful name in the textbox for Output Device. In the drop-down list of Device Type,
select the Device Type you have previously uploaded into the SAP system.
Figure 9 Defining Printing Method
Under the ‘Access Method’, define your Host Spool Access Method. In the above example,
method “G: Front End Printing with Control Tech’ will prompt user to select a list of installed
printer driver under the ‘Printer and Faxes’ in your Windows platform.
Note: Method G is used here just for the simplicity during testing.
Save the setting once the necessary information has been entered.
SAP Device Driver for SATO Printers
User Manual
14-50
Functionalities of
SATO-SAP Printer
Driver
6
‘SAP ABAP-Based Printer Driver for SATO printers’ provides the following printing features:
6.1 Barcode
Both SAP traditional and new barcode symbology are supported. (Please refer to SAP notes:
430887 and 645158 for more information about the barcode symbology).
For New Barcode Technology (NBT), user only needs to define the barcode in SE73 transaction
as System Barcode. The NBT supports the following barcodes:
Figure 10 Barcodes in New Barcode Technology
For Traditional (old) Barcode, user needs to create the required barcode definition as System
Barcode in SE73. Then link the barcode definition to the print control as Printer Barcode. The
following shows the provided Print Control in SATO Device Types:
Barcode Type
Postnet
UUC/EAN128
NW-7 (Codabar, Ratio 1:3)
Interleaved 2 of 5 (Ratio 1:3)
JAN/EAN13 (Ratio 1:3)
JAN/EAN8 (Ratio 1:3)
UPC-A (Ratio 1:3)
NW-7 (Codabar, Ratio 1:2)
Interleaved 2 of 5 (Ratio 1:2)
JAN/EAN13 (Ratio 1:2)
JAN/EAN8 (Ratio 1:2)
UPC-A (Ratio 1:2)
NW-7 (Codabar, Ratio 2:5)
SAP Device Driver for SATO Printers
User Manual
SAP Print Control
SBP07
XB012
XB101-XB112
XB121-XB132
XB141-XB152
XB161-XB172
XB181-XB192
XB201-XB212
XB221-XB232
XB241-XB252
XB261-XB272
XB281-XB292
XB301-XB312
SBPL command
ESC+BP
ESC+BI
ESC+B0<module width>
ESC+B2<module width>
ESC+B3<module width>
ESC+B4<module width>
ESC+BH<module width>
ESC+D0<module width>
ESC+D2<module width>
ESC+D3<module width>
ESC+D4<module width>
ESC+DH<module width>
ESC+BD0<module width>
15-50
Barcode Type
Interleave 2 of 5 (Ratio 2:5)
JAN/EAN13 (Ratio 2:5)
JAN/EAN8 (Ratio 2:5)
UPC-A (Ratio 2:5)
Code 39 (Ratio 1:3)
Code 39 (Ratio 1:2)
Code 39 (Ratio 2:5)
Code 93
SAP Print Control
XB321-XB332
XB341-XB352
XB361-XB372
XB381-XB392
XB501-XB512
XB521-XB532
XB541-XB552
XB561-XB572
SBPL command
ESC+BD2<module width>
ESC+BD3<module width>
ESC+BD4<module width>
ESC+BDH<module width>
ESC+B1<module width>
ESC+D1<module width>
ESC+BD1<module width>
ESC+BC<module width>
Table 4 Barcode Print Controls
* Note: The SATO PDL Driver supports Barcode Code 128 Type-A, Type-B, Type-C and
Auto-Switch. Please refer t o SAP Note: 645158 for the approach to use this barcode.
6.1.1 Defining Barcode
Before a Barcode can be used in the Smart Forms, the definition of the Barcode must be made.
SE73 – SAPScript Font Maintenance
Enter Transaction code SE73 to enter to the following screen.
Figure 11 Transaction Code 73 – SAPScript Font Maintenance
Choose the ‘System Bar Codes’ and then click the ‘Change’ button to go the following screen.
SAP Device Driver for SATO Printers
User Manual
16-50
Figure 12 System Barcode screen
Click the ‘Create’ button or press ‘F5’ key to create a new System Barcode definition.
Figure 13 Create Button
6.1.2 New Barcode Technology
The following describes how to create a barcode with new Barcode Technology.
Figure 14 Choosing Barcode Technology
SAP Device Driver for SATO Printers
User Manual
17-50
The ‘New Barcode Technology’ supports the following barcodes:
- Code39
- PDF417
- Code93
- 2 of 5 Interleaved
- Code128
Click on the ‘New’ button to enter the following screen.
Figure 15 Entering Barcode information
For SATO barcode, it is recommended to define a Barcode name with prefix ‘YST’. For
example, to define a new Code39 barcode, the following Barcode name can be used:
YSTCd39
Enter some description on the textbox for ‘Short text’. Press the tick button to continue.
Figure 16 Selecting the Barcode Type
SAP Device Driver for SATO Printers
User Manual
18-50
Figure 17 Choosing the Barcode alignment
Figure 18 Entering Barcode Information
Figure 19 Saving the Barcode definition
SAP Device Driver for SATO Printers
User Manual
19-50
Figure 20 Saving the definition to workspace
That is all for the System Barcode definition. The next step will be defining the Printer Barcode
in order to link the System Barcode to the Printer Control in the device type.
6.1.3 New Technology Barcode
For more information about the SATO Barcode printing command, please refer to the printer
command specifications.
Code 39
This barcode is to start and end with ‘*’ characters. If the given data is not started and ended
with the ‘*’ character, then the SATO-SAP printer driver will add the characters to the data
automatically.
The printer will generate a ‘beep’ sound if invalid data is given.
Code 93
The maximum number of data for this barcode is 99. The printer, not the printer driver, will
generate a check digit when the data is printed on the printer.
Code 128
For example, if the data ‘123456’ was given, the following SBPL command will be generated by
the printer driver: … BG03158>H123456.
Please refer to SAP Note: 645158 for input approach for the Barcode Code 128. If unexpected
values were received by the SATO PDL Driver, the barcode might not be printed.
Interleaved 2 of 5
The given data of this barcode must be even number. If odd number data is given, SATO-SAP
printer driver will generate a ‘0’ in front of the given data.
For example,
If ‘12345’ was given, the barcode with value ‘012345’ will be printed.
PDF 417
Minimum module width can be set to 01 and 02; however, this may not be read properly.
Note: For rotated PDF417 Barcode, the printed location on the label might differ from what
shown on the print preview. User might want to adjust the position in the Smart Forms to get the
required positioning.
SAP Device Driver for SATO Printers
User Manual
20-50
RFID Gen2 Tag
User is to enter the necessary data based on the following descriptions:
RFID
Attribute:
Representation in barcode field data:
EPC value
EPC:xxxxxxxxxxxxxxxxxxxxxxxx;
(xxxxxxxxxxxxxxxxxxxxxxxx is 24 digit hex value representing 12 bytes)
PC value
PC:xxxxxxxxxxxxxxxxxxxxxxxx;
(xxxxxxxxxxxxxxxxxxxxxxxx
is
24
digit
hex
value
representing 12 bytes)
(SATO Device Driver does not support this feature)
USR value
USR:xxxxxxxxxxxxxxxxxxxxxxxx;
(xxxxxxxxxxxxxxxxxxxxxxxx is 24 digit hex value representing 12 bytes)
ACS
passcode
ACS:yyyyyyyy;
(yyyyyyyy is 8 digit hex value representing 4 bytes)
LOCKMASK
LM:yy;
(yy is 2 digit hex value representing 1 byte:
0x01 – Lock EPC+PC
0x02 – Perma-lock EPC+PC )
0x04 – Lock USR
0x08 – Perma-lock USR
KILL
passcode
KILL:yyyyyyyy;
(yyyyyyyy is 8 digit hex value representing 4 bytes)
Table 5 RFID Attributes
Examples:
Barcode data field contents:
Meaning:
EPC:F2A07895C1710708090A0B0C;
Numerical (hexadecimal) data for EPC
USR:F2A07895C171010203040506;EPC:01
9975F3ABB0010203040506;
Numerical data for USR and EPC banks
EPC:112233445566010203040506;ACS:12
24489F;LM:01;
Numerical data for EPC bank,
ACS passcode for LOCK operation is
1224489F,
Memory banks EPC+PC are locked
EPC:1122334455660708090A0B0C;USR:01
12248D8F060708090A0B0C;ACS:1234567A
;LM:0A;
Numerical data for EPC and USR banks,
ACS passcode for PERMALOCK operation
is 1234567A,
Memory banks EPC+PC and USR are
perma-locked
EPC:123456789ABC0708090A0B0C;KILL:1
234567F;
Numerical data for EPC,
KILL passcode is 1234567F
Table 6 RFID input examples
SAP Device Driver for SATO Printers
User Manual
21-50
6.1.4 Old Barcode Technology (Conventional System Barcode)
Click the ‘Old’ button (as in Figure 14 Choosing Barcode Technology) to define a Barcode with
Old Barcode Technology.
Figure 21 Defining Barcode with Old Barcode Technology
* In Old Barcode Technology, there is no way to define the Barcode Module Width. Thus, print
controls with such information have been defined. User is to select the print control which
carries required Barcode Module Width.
6.1.5 Old Technology Barcode
Interleaved 2 of 5
The given data of this barcode must be even number. If odd number data is given, SATO-SAP
printer driver will generate a ‘0’ in front of the given data.
For example,
If ‘12345’ was given, the barcode with value ‘012345’ will be printed.
CODABAR
The barcode includes start and stop characters: A,B,C,D,E,N,T,a,b,c,d,e,n,t. If the given data is
not started and ended with the start/stop characters, then the SATO-SAP printer driver will
embedded the data with Start/Stop character ‘A’.
POSTNET
The SATO-SAP printer driver supports the US Postal Service POSTNET barcode with the
following formats:
- 5 digits (Postnet-32 format)
- 6 digits (Postnet-37 format)
- 9 digits (Postnet-52 format)
- 11 digits (Postnet-62 Delivery Point format)
If data with other formats than above was given, the SATO printer will generate a ‘beep’ sound
to indicate invalid data.
SAP Device Driver for SATO Printers
User Manual
22-50
UPC Barcode Type A
The data of this barcode should be 11 digits + 1 check digit. If user supplies 12 digits data, then
SATO-SAP printer driver will assume the last digit is the given check digit. Else, the driver will
generate the check digit.
EAN 8 Barcode
The data of this barcode should be 7 digits + 1 check digit. If user supplies 8 digits data, then
SATO-SAP printer driver will assume the last digit is the given check digit. Else, the driver will
generate the check digit based on Modulo 10 formula.
EAN 13 Barcode
The data of this barcode should be 12 digits + 1 check digit. If user supplies 13 digits data, then
SATO-SAP printer driver will assume the last digit is the given check digit. Else, the driver will
generate the check digit based on Modulo 10 formula.
Code 39
Code39 is an alphanumeric code that can represent the following characters in the bar code
data:
Numbers:
1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
The start and stop character for the Code39 bar code is represented by an asterisk (*) in the
text view of the bar code data (also called "human-readable text" or "interpretation line").
If the given data is enclosed in asterisk (*), no check digit will be generated by the driver.
Code 93
Code93 is an alphanumeric code that can represent the following characters directly in the bar
code data:
Numbers:
1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
6.1.6 Defining Printer Barcodes
Once the System Barcode (Old Technology) has been defined, then proceed to define the
printer barcode. Note: This step is not required for barcode defined with New Barcode
Technology.
SAP Device Driver for SATO Printers
User Manual
23-50
Figure 22 Printer Barcode Definition
Choose the ‘Printer Barcodes’ and then click the ‘Change’ button to create a Printer Barcode
definition.
Figure 23 Device List for Printer Barcodes
Double click the SATO device type which starts with prefix ‘YST’.
SAP Device Driver for SATO Printers
User Manual
24-50
Figure 24 Printer Barcode List in the device type
Click on the ‘Create’ button or ‘F5’ key to create a new definition of Printer Barcode.
Figure 25 Defining Printer Barcode
Select the System Barcode which has been defined previously from the entry list. Then key in
the required Print Control. Note: Key in the same print control for both ‘Bar code prefix’ and ‘Bar
code suffix’.
Refer to Table 4 Barcode Print Controls for the available print control definition in the device
type.
SAP Device Driver for SATO Printers
User Manual
25-50
6.2 Fonts
SATO-SAP Printer Driver supports the following fonts:
Latin 1 (ISO8859-1 codepage) device types:
SAP Font
SATO Font
HELVETICA
CG Triumvirate
TIMES
CG Times
English only device types:
SAP Font
SATO Font
HELVETICA
CG Triumvirate
TIMES
CG Times
COURIER
Helvetica Outline Font, fixed
BOLD
character pitch
(optional Italic)
LETGOTH
SATO Fixed Size M Font
LNPRINT
SATO Fixed Size S Font
Codepage 850 device types :
SAP Font
SATO Font
HELVETICA
CG Triumvirate
TIMES
CG Times
COURIER
Helvetica Outline Font, fixed
BOLD
character pitch
(optional Italic)
Type
Scalable
Scalable
SBPL Command
ESC+RDB
ESC+RDA
Type
Scalable
Scalable
Scalable
SBPL Command
ESC+RDB
ESC+RDA
ESC+$B, ESC+$=
Bitmap, fixed size
Bitmap, fixed size
ESC+M
ESC+S
Type
Scalable
Scalable
Scalable
SBPL Command
ESC+RDB
ESC+RDA
ESC+$B, ESC+$=
Korean (Wangsung Encoding/Unicode) device types:
SAP Font
SATO Font
Type
KPBATANG
HYRGothic-Medium
Scalable
Proportional
SBPL Command
ESC+RDK
Simplified Chinese (GB2312/Unicode) device types:
SAP Font
SATO Font
Type
CNSONG
MKaiSO-Medium-U
Scalable
Proportional
SBPL Command
ESC+RDC
Traditional Chinese (Big 5/Unicode) device types:
SAP Font
SATO Font
Type
TWSONG
MHeiS-Bold -U
Scalable
Proportional
SBPL Command
ESC+RDc
Japanese (Shift-JIS) device types:
SAP Font
SATO Font
DBGothic,
SATO Japanese resident
DBMincho,
bitmap font
JPMincho
Type
Bitmap, fixed size
SBPL Command
ESC+K
Table 7 Supported font in SATO-SAP Printer Driver
For Fixed size SATO Resident Font, please refer to the Font Appendix for a list of supported
size of the font.
SAP Device Driver for SATO Printers
User Manual
26-50
Note:
1. SATO 203dpi printer does not support printing of 8 point or lower Courier Font
(ESC+$A, ESC+$B, ESC+$=). It will be printed in a slightly larger size instead.
2. There could be some discrepancies of the string length shown on SmartForms and
what printed from printer. This is because when converting the SAP font point size into
SATO font dot size for specific resolution, there is a rounding up of fractions in the
calculation.
3. For Japanese device types which offer SATO Resident Bitmap fonts, the Japanese text
will appear shorter than what shown on the print preview of SmartForms. This is
because the width of the 1-byte characters in the SAP Japanese fonts is 0.5 time of the
2-byte characters. But in SATO Japanese fonts, the width of the 1-byte characters is
slightly larger, about 0.6 times, of the 2-byte characters.
SAP Device Driver for SATO Printers
User Manual
27-50
6.3 SmartStyles
Enter Transaction code ‘smartstyles’ to use the Smart Styles application.
Figure 26 SmartStyles
Create or edit a SmartStyles to define the printing items which are to be used in the Smart
Forms.
Figure 27 Create node of printing items
Right click on the ‘Character Formats’ and choose ‘Create Node’.
SAP Device Driver for SATO Printers
User Manual
28-50
Figure 28 Defining Barcode printing item in SmartStyles
Figure 29 Defining Font Printing item in SmartStyles
After defining the necessary Barcode and Fonts as printing items, check and activate the
SmartStyles.
Figure 30 Check and Activate the SmartStyles
SAP Device Driver for SATO Printers
User Manual
29-50
6.4 Smart Forms
Enter transaction code /nsmartforms to run the Smart Forms application.
Figure 31 Smart Forms application
Create or edit a Smart Forms which the name is prefixed with ‘YST’.
Figure 32 Applying the SmartStyles
Click on the ‘Global settings’->’Form Attributes’, in the ‘Output Options’, apply the SmartStyles
defined previously.
SAP Device Driver for SATO Printers
User Manual
30-50
6.4.1 Adding Text
Right click on the ‘Page1’, choose ‘Create’->’Window’.
Figure 33 Creating Window
Give the Window component a meaningful name. Then right click on it and create a ‘Text’
component.
Figure 34 Creating Text Component
SAP Device Driver for SATO Printers
User Manual
31-50
Figure 35 Defining Text Component
Under the ‘Output Options’ tab, select the SmartStyles which previously defined. So that the text
printing item can be available to use.
Figure 36 Adding Text
Click on the ‘General Attributes’ tab and click on the ‘Editor’ button to insert the text. Note: This
procedure could be varied depending on the editor mode.
Figure 37 Entering the text with format
The message is embedded in format tags. In the above example, the message is included in
<H0> and </> format tags which specify the SATO CG Triumvirate Font (ESC+RD) . Format H0
is a text printing item defined in the SmartStyles.
SAP Device Driver for SATO Printers
User Manual
32-50
6.4.2 Adding Barcode
Define a ‘Window’ component under ‘Page1’ and give it a meaningful name. From this new
window create a ‘Text’ component.
Figure 38 Creating Barcode component
Apply the SmartStyles in the ‘Output Options’. Then in the Editor under ‘General Attributes’,
type the Barcode value, and apply the Barcode printing format.
Figure 39 Entering Barcode value
The message is embedded in format tags. In the above example, the message is included in
<B2> and </> format tags which specify the SATO Code 128A Barcode. Format B2 is a
Barcode printing item defined in the SmartStyles
SAP Device Driver for SATO Printers
User Manual
33-50
6.4.3 Adding Images
Figure 40 Creating Image component
Select the required image from the Name drop-down list under the General Attributes. Then key
in the Resolution information for the image. For example, if the image is to be printed in 300
resolution printer, then select 300 from the Resolution field.
Currently, the images supported by SATO-SAP Printer Driver have the following constraints:
- Only ‘Black and White Bitmap Images’ are supported
- The images cannot be ‘compressed’ when uploaded using Transaction code SE78.
SAP Device Driver for SATO Printers
User Manual
34-50
6.4.4 Positioning Printing Components
Form Painter
Figure 41 Positioning printing items
The positions of the printing items can be adjusted by drag & drop the components in the ‘Form
Painter’. Alternatively, it can be done by manipulating the values in the Left and Upper margin
fields under the ‘Output Options’ tab of the window component.
6.4.5 Printing the Smart Forms
After the Smart Forms has been made, it has to be checked and activated before it can be
printed.
Figure 42 Check and Activate the Smart Forms
Figure 43 Printing Smart Forms
Click the ‘Print’ button to continue.
SAP Device Driver for SATO Printers
User Manual
35-50
Figure 44 Printing Screen
Click the ‘Execute’ button to continue.
Figure 45 Printing Screen - Select the output device
Select the required Output Device and check on the ‘Print Immediately’ checkbox. Then click
the ‘Print’ button to print.
SAP Device Driver for SATO Printers
User Manual
36-50
6.5 System Commands
User can specify the System Commands of SBPL in the Smart Forms label by using the
Command nodes.
Right click on the Window node->Create->Flow Logic->Command to display Command node
feature.
Figure 46 Defining System Command using Command node
Under the ‘Output Options’, user is to define the System Command in the Name-Value pairs
format. The value must be enclosed within the single quote character ( ‘ ) or empty,
depending on the command.
Figure 47 Name-Value pairs information
SAP Device Driver for SATO Printers
User Manual
37-50
The following are the available system commands:
Function
Command Name
Command
Value
1~11
SBPL
Command
ESC+CS
Print Speed
PRINT_SPEED
Print
Darkness
PRINT_DARKNESS
ab,
a: 1~ 5
b: A~F
ESC+#E
Label Size
LABEL_SIZE
Refer to the
command
specification
ESC+A1
The printer driver
will generate a
default ESC+A1
command, based
on the label size of
designed Smart
Forms, if this
System command
is not specified.
Start Print
Correction
START_POINT
Refer to the
command
specification
ESC+A3
The printer driver
will generate a
default ESC+A3
command, based
on the position of
the designed Smart
Forms, if this
System command
is not specified.
Enlargement
of Print Area
ENLARGEMENT_AREA
No value is
needed
ESC+AX
Standard
Print Area
STANDAR_AREA
No value is
needed
ESC+AR
Print End
Position
PRINT_END_POS
No value is
needed
ESC+EP
Multiple
Cutting
MULTIPLE_CUT
0~9999
ESC+~(Null)
This command is
valid only when the
printer is equipped
with cutter
No. of Labels
per Cut
Segment
CUT_SEGMENT
0~9999
ESC+~A
This command is
valid only when the
printer is equipped
with cutter
Cutting
Operation
CUT_OPERATION
No value is
needed
ESC+~B
This command is
valid only when the
printer is equipped
with cutter
Auto Linefeed
AUTO_LINEFEED
0~999
ESC+E
SAP Device Driver for SATO Printers
User Manual
Remarks
38-50
90 degree
Text Rotation
ROTATE_90_x
Name of
Window to
be rotated
ESC+%1
x is any number to
make sure the
command name is
not repeated in the
SmartForms
180 degree
Text Rotation
ROTATE_180_x
Name of
Window to
be rotated
ESC+%2
x is any number to
make sure the
command name is
not repeated in the
SmartForms
270 degree
Text Rotation
ROTATE_270_x
Name of
Window to
be rotated
ESC+%3
x is any number to
make sure the
command name is
not repeated in the
SmartForms
Page Number
PRINT_QUANTITY
Number of
pages to
print
ESC+Q
It is print command
is not specified, the
page is printed
once. Example of
the value:
'%PAGE2:4'
This means the
page with name
“%PAGE2” will be
printed 4 times.
Subsequent page
number can be
added with a
comma separator.
For example,
'%PAGE2:4,
%PAGE3:3' This
means page
‘%PAGE2’ is
printed 4 times and
page ‘%PAGE3’ is
printed 3 times
Table 8 System Commands
It is important to refer to the command specification of the printer models to understand the
correct range of value can be used for the Command values. Note that the Command Names
are case-sensitive.
System command should be used carefully. Invalid input may result in unexpected outcome of
the printout.
SAP Device Driver for SATO Printers
User Manual
39-50
The table below shows the supported System Commands on models
Model PT4xxe/ CT4xxi
SR4xx LT4xx/CL4xx/MR4xxe/
MB4xxi
GT4xxe/GTxxe/M84Pro/
M10e
Command
PRINT_SPEED
O
O
O
O
S-84
O
PRINT_DARKNESS
O
O
O
O
O
LABEL_SIZE
O
O
O
O
O
START_POINT
O
O
O
O
O
ENLARGEMENT_AREA
O
O
STANDARD_AREA
O
O
PRINT_END_POS
O
O
O
O
MULTIPLE_CUT
O*
O*
O*
O*
CUT_SEGMENT
O*
O*
O*
O*
CUT_OPERATION
O*
O*
O*
O*
AUTO_LINEFEED
O
O
O
O
O
ROTATE_xx_X
O
O
O
O
O
PRINT_QUANTITY
O
O
O
O
O
Figure 48 System Commands on Models
*: Only possible when the Cutter Unit is installed.
SAP Device Driver for SATO Printers
User Manual
40-50
6.5.1
Text and Image Rotation
To rotate a text or an image on SmartForms, user is to create a command in the window to be
rotated. The name of parameter (e.g., ROTATE_180_x) should not be repeated. Image below is
an example of how the rotated text can be setup:
Figure 49 Text Rotation
Rotation Result:
Figure 50 Rotation result
Please refer to the command specification for the behavior of the rotation.
There are a few restrictions on the Rotation functions:
- SmartForm will not display the rotated text on the print preview. User is to adjust the
position of the window by checking the actual printout.
- The rotated text should not have more than 1 line.
- Each rotated window should have only 1 line of text or only 1 image.
SAP Device Driver for SATO Printers
User Manual
41-50
Limitations
7
Please note the following are not supported by the SATO PDL Driver:
- Compressed graphics and color bitmap
- Underlined, superscript and subscript text
- There could be some slight variations of font size in SmartForms and the actual font
size printed from SATO printer. This is due to the size conversion and rounding up
issues.
- Courier Font (which will be mapped to SATO Fixed Width Scalable font) does not
support 8 points or lower font size printing in 203dpi printer. It will be printed in a slightly
larger font size instead.
- Some European characters from ISO8859-1 and Codepage 850 device types are not
available from printer. Please refer to the command specifications of printer for details.
For other functionalities of SATO printers which are not supported by the SATO PDL driver,
please approach the technical team of SATO for customization requests at
global.sysdev@sato-int.com
SAP Device Driver for SATO Printers
User Manual
42-50
Appendix
8.1 Print Controls List for Barcode
8
For the control list of New Barcode Technology, please refer to Table 4 Barcode Print Controls.
The following is the control list for the old barcodes:
Barcode (Ratio 1:3)
NW-7 (CODABAR)
SAP Print
Narrow
Control
Bar Width
1
2
3
4
5
6
7
8
9
10
11
12
Mapped to
SBPL
Command
ESC+B001
ESC+B002
ESC+B003
ESC+B004
ESC+B005
ESC+B006
ESC+B007
ESC+B008
ESC+B009
ESC+B010
ESC+B011
ESC+B012
Interleaved 2 of 5
SB121
SB122
SB123
SB124
SB125
SB126
SB127
SB128
SB129
SB130
SB131
SB132
1
2
3
4
5
6
7
8
9
10
11
12
ESC+B201
ESC+B202
ESC+B203
ESC+B204
ESC+B205
ESC+B206
ESC+B207
ESC+B208
ESC+B209
ESC+B210
ESC+B211
ESC+B212
JAN/EAN13
SB141
SB142
SB143
SB144
SB145
SB146
SB147
SB148
1
2
3
4
5
6
7
8
ESC+B301
ESC+B302
ESC+B303
ESC+B304
ESC+B305
ECS+B306
ESC+B307
ESC+B308
SB101
SB102
SB103
SB104
SB105
SB106
SB107
SB108
SB109
SB110
SB111
SB112
SAP Device Driver for SATO Printers
User Manual
43-50
SB149
SB150
SB151
SB152
9
10
11
12
ESC+B309
ESC+B310
ESC+B311
ESC+B312
JAN/EAN8
SB161
SB162
SB163
SB164
SB165
SB166
SB167
SB168
SB169
SB170
SB171
SB172
1
2
3
4
5
6
7
8
9
10
11
12
ESC+B401
ESC+B402
ESC+B403
ESC+B404
ESC+B405
ESC+B406
ESC+B407
ESC+B408
ESC+B409
ESC+B410
ESC+B411
ESC+B412
UPC-A
SB181
SB182
SB183
SB184
SB185
SB186
SB187
SB188
SB189
SB190
SB191
SB192
1
2
3
4
5
6
7
8
9
10
11
12
ESC+BH01
ESC+BH02
ESC+BH03
ESC+BH04
ESC+BH05
ESC+BH06
ESC+BH07
ESC+BH08
ESC+BH09
ESC+BH10
ESC+BH11
ESC+BH12
PostNet
SB007
ESC+BP
Barcode (Ratio 1:2)
NW-7 (CODABAR)
SAP Print
Narrow
Control
Bar Width
SB201
SB202
SB203
SB204
SB205
SB206
SB207
SB208
SB209
SB210
SB211
1
2
3
4
5
6
7
8
9
10
11
SAP Device Driver for SATO Printers
User Manual
Mapped to
SBPL
Command
ESC+D001
ESC+D002
ESC+D003
ESC+D004
ESC+D005
ESC+D006
ESC+D007
ESC+D008
ESC+D009
ESC+D010
ESC+D011
44-50
SB212
12
ESC+D012
Interleaved 2 of 5
SB221
SB222
SB223
SB224
SB225
SB226
SB227
SB228
SB229
SB230
SB231
SB232
1
2
3
4
5
6
7
8
9
10
11
12
ESC+D201
ESC+D202
ESC+D203
ESC+D204
ESC+D205
ESC+D206
ESC+D207
ESC+D208
ESC+D209
ESC+D210
ESC+D211
ESC+D212
JAN/EAN13
SB241
SB242
SB243
SB244
SB245
SB246
SB247
SB248
SB249
SB250
SB251
SB252
1
2
3
4
5
6
7
8
9
10
11
12
ESC+D301
ESC+D302
ESC+D303
ESC+D304
ESC+D305
ESC+D306
ESC+D307
ESC+D308
ESC+D309
ESC+D310
ESC+D311
ESC+D312
JAN/EAN8
SB261
SB262
SB263
SB264
SB265
SB266
SB267
SB268
SB269
SB270
SB271
SB272
1
2
3
4
5
6
7
8
9
10
11
12
ESC+D401
ESC+D402
ESC+D403
ESC+D404
ESC+D405
ESC+D406
ESC+D407
ESC+D408
ESC+D409
ESC+D410
ESC+D411
ESC+D412
UPC-A
SB281
SB282
SB283
SB284
SB285
SB286
SB287
1
2
3
4
5
6
7
ESC+DH01
ESC+DH02
ESC+DH03
ESC+DH04
ESC+DH05
ESC+DH06
ESC+DH07
SAP Device Driver for SATO Printers
User Manual
45-50
SB288
SB289
SB290
SB291
SB292
8
9
10
11
12
Barcode (Ratio 2:5)
NW-7 (CODABAR)
SAP Print
Narrow
Control
Bar Width
SB301
SB302
SB303
SB304
SB305
SB306
SB307
SB308
SB309
SB310
SB311
SB312
ESC+DH08
ESC+DH09
ESC+DH10
ESC+DH11
ESC+DH12
Mapped to
SBPL
Command
1
2
3
4
5
6
7
8
9
10
11
12
ESC+BD001
ESC+BD002
ESC+BD003
ESC+BD004
ESC+BD005
ESC+BD006
ESC+BD007
ESC+BD008
ESC+BD009
ESC+BD010
ESC+BD011
ESC+BD012
Interleaved 2 of 5
SB321
SB322
SB323
SB324
SB325
SB326
SB327
SB328
SB329
SB330
SB331
SB332
1
2
3
4
5
6
7
8
9
10
11
12
ESC+BD201
ESC+BD202
ESC+BD203
ESC+BD204
ESC+BD205
ESC+BD206
ESC+BD207
ESC+BD208
ESC+BD209
ESC+BD210
ESC+BD211
ESC+BD212
JAN/EAN13
SB341
SB342
SB343
SB344
SB345
SB346
SB347
SB348
SB349
SB350
SB351
SB352
1
2
3
4
5
6
7
8
9
10
11
12
ESC+BD301
ESC+BD302
ESC+BD303
ESC+BD304
ESC+BD305
ESC+BD306
ESC+BD307
ESC+BD308
ESC+BD309
ESC+BD310
ESC+BD311
ESC+BD312
SAP Device Driver for SATO Printers
User Manual
46-50
JAN/EAN8
SB361
SB362
SB363
SB364
SB365
SB366
SB367
SB368
SB369
SB370
SB371
SB372
1
2
3
4
5
6
7
8
9
10
11
12
ESC+BD401
ESC+BD402
ESC+BD403
ESC+BD404
ESC+BD405
ESC+BD406
ESC+BD407
ESC+BD408
ESC+BD409
ESC+BD410
ESC+BD411
ESC+BD412
UPC-A
SB381
SB382
SB383
SB384
SB385
SB386
SB387
SB388
SB389
SB390
SB391
SB392
1
2
3
4
5
6
7
8
9
10
11
12
ESC+BDH01
ESC+BDH02
ESC+BDH03
ESC+BDH04
ESC+BDH05
ESC+BDH06
ESC+BDH07
ESC+BDH08
ESC+BDH09
ESC+BDH10
ESC+DBH11
ESC+BDH12
Code 39 (Ratio 1:3)
SB501
1
SB502
2
SB503
3
SB504
4
SB505
5
SB506
6
SB507
7
SB508
8
SB509
9
SB510
10
SB511
11
SB512
12
ESC+B101
ESC+B102
ESC+B103
ESC+B104
ESC+B105
ESC+B106
ESC+B107
ESC+B108
ESC+B109
ESC+B110
ESC+B111
ESC+B112
Code 39 (Ratio 1:2)
SB521
1
SB522
2
SB523
3
SB524
4
SB525
5
SB526
6
SB527
7
SB528
8
SB529
9
ESC+D101
ESC+D102
ESC+D103
ESC+D104
ESC+D105
ESC+D106
ESC+D107
ESC+D108
ESC+D109
SAP Device Driver for SATO Printers
User Manual
47-50
SB530
SB531
SB532
10
11
12
ESC+D110
ESC+D111
ESC+D112
Code 39 (Ratio 2:5)
SB541
1
SB542
2
SB543
3
SB544
4
SB545
5
SB546
6
SB547
7
SB548
8
SB549
9
SB550
10
SB551
11
SB552
12
ESC+BD101
ESC+BD102
ESC+BD103
ESC+BD104
ESC+BD105
ESC+BD106
ESC+BD107
ESC+BD108
ESC+BD109
ESC+BD110
ESC+BD111
ESC+BD112
Code 93
SB561
SB562
SB563
SB564
SB565
SB566
SB567
SB568
SB569
SB570
SB571
SB572
ESC+BC01
ESC+BC02
ESC+BC03
ESC+BC04
ESC+BC05
ESC+BC06
ESC+BC07
ESC+BC08
ESC+BC09
ESC+BC10
ESC+BC11
ESC+BC12
1
2
3
4
5
6
7
8
9
10
11
12
SAP Device Driver for SATO Printers
User Manual
48-50
8.2 Font Print Controls
203dpi
ESC+M
(13x20)
(Courcyr)
ESC+S
(8x15)
(Lnprint)
ESC+L
1
2
3
4
5
6
7
8
9
10
11
12
305dpi
609dpi
7
14
21
28
36
43
50
57
64
71
78
85
5
9
14
19
24
28
33
38
43
47
52
57
2
5
7
10
12
14
17
19
21
24
26
28
Print
Control
SF301
SF302
SF303
SF304
SF305
SF306
SF307
SF308
SF309
SF310
SF311
SF312
5
11
16
21
27
32
37
43
48
53
59
64
4
7
11
14
18
21
25
28
32
35
39
43
2
4
5
7
9
11
12
14
16
18
20
21
SF201
SF202
SF203
SF204
SF205
SF206
SF207
SF208
SF209
SF210
SF211
SF212
Point
1
2
3
4
5
6
7
8
9
10
11
12
Note: The fixed size resident fonts are only supported in English-only Device Types.
Other font information can be found at section 6.2 Fonts.
SAP Device Driver for SATO Printers
User Manual
49-50
SATO GROUP OF COMPANIES
Asia Pacific & Oceania Region
SATO ASIA PACIFIC PTE. LTD.
438A Alexandra Road #05-01/04,
Alexandra Technopark, Singapore 119967
Tel: +65-6271-5300
Fax: +65-6273-6011
Email: technical@satoasiapacific.com
www.satoasiapacific.com
SATO AUTO-ID MALAYSIA SDN. BHD.
No.25, Jalan Pemberita U1/49,
Temasya Industrial Park, Section U1,
40150 Shah Alam, Selangor Darul Ehsan,
Malaysia
Tel: +60-3-7620-8901
Fax: +60-3-5569-4977
Email: service@satosms.com.my
www.satoasiapacific.com
SATO AUTO-ID (THAILAND) CO., LTD.
292/1 Moo 1 Theparak Road,
Tumbol Theparak, Amphur Muang,
Samutprakarn 10270, Thailand
Tel: +66-2-736-4460
Fax: +66-2-736-4461
Email: technical@satothailand.com
www.satothailand.co.th
SATO SHANGHAI CO., LTD.
307 Haining Road, ACE Bldg,
10th Floor, Hongkou Area, Shanghai,
China 200080
Tel: +86-21-6306-8899
Fax: +86-21-6309-1318
Email: tech@satochina.com
www.satochina.com
SATO ASIA PACIFIC PTE. LTD.
Korea Representative Office
6F, Korea Housing Center,
Yeouido-dong 45-11, Yeongdeungpo-gu,
Seoul, Korea 150-736
Tel: +82-2-761-5072
Fax: +82-2-761-5073
Email: technical@satoasiapacific.com
www.satoasiapacific.com
SATO ASIA PACIFIC PTE. LTD.
India Representative Office
Regus Level 2, Connaugh Place,
Bund Garden Road, Pune. 411001, India
Tel: +91-20-4014-7747
Fax: +91-20-4014-7576
Email: technical@satoasiapacific.com
www.satoasiapacific.com
SATO NEW ZEALAND LTD.
30 Apollo Drive, Mairangi Bay
Auckland, New Zealand
Tel: +64 9-477-2222
Fax: +64-9-477-2228
Email:
global.warranty@satonewzealand.com
www.satonewzealand.com
European Region
SATO LABELLING SOLUTIONS
EUROPE GmbH (BELGIUM)
Leuvensesteenweg 369,
1932 Sint-Stevens-Woluwe, Belgium
Tel: +32-2-788-80-00
Fax: +32-2-788-80-80
Email: info@nl.satoeurope.com
www.satoeurope.com
SATO LABELLING SOLUTIONS
EUROPE GmbH (GERMANY)
Ersheimer Straße 71,
69434 Hirschhorn, Germany
Tel: +49-6272-9201-160
Fax: +49-6272-9201-347
Email: service@de.satoeurope.com
www.satoeurope.com
SATO LABELLING SOLUTIONS
EUROPE GmbH (NORWAY)
Hovfaret 4 0275 Oslo, Norway
Tel.: +47-225-106-70
Fax: +47-225-106-71
Email: kundeservice@satonorge.com
www.satoeurope.com
SATO LABELLING SOLUTIONS
EUROPE GmbH (NETHERLANDS)
Techniekweg 1b, 3481 MK Harmelen,
Netherlands
Tel.: +31-348-444437
Fax: +31-348-446403
Email: info@nl.satoeurope.com
www.satoeurope.com
SATO LABELLING SOLUTIONS
EUROPE GmbH (ITALY)
Viale Europa 39/1,
20090 Cusago, Milano, Italy
Tel.: +39-2-903-944-64
Fax: +39-2-903-940-35
Email: info@it.satoeurope.com
www.satoeurope.com
SATO AUSTRALIA PTY LTD.
SATO LABELLING SOLUTIONS
EUROPE GmbH (SWITZERLAND)
1/1 Nursery Avenue, Clayton Business
Park, Clayton, VIC 3168 Australia
Tel: +61-3-8814-5330
Fax: +61-3-8814-5335
Email: enquiries@satoaustralia.com
www.satoaustralia.com
Allmendstraße 19,
8320 Fehraltorf, Switzerland
Tel: +41-44-954-84-00
Fax: +41-44-954-84-09
Email: info@ch.satoeurope.com
www.satoeurope.com
SATO LABELLING SOLUTIONS
EUROPE GmbH (AUSTRIA)
Niederlassing Austria
Jochen-Rindt-Straße 13
1230 Wien, Austria
Tel: +43-2762-52690
Fax: +43-2762-52018
Email: info@at.satoeurope.com
www.satoeurope.com
SATO LABELLING SOLUTIONS
EUROPE GmbH (DENMARK)
Naverland 29A DK-2600
Glostrup, Denmark
Tel.: +45-43204700
Fax: +45-43204709
Email: info@dk.satoeurope.com
www.satoeurope.com
SATO POLSKA SP. Z O.O.
ul. Wrocławska 123, 55-015 Radwanice
Św. Katarzyna, Poland
Tel: +48-71-381-03-60
Fax: +48-71-381-03-68
Email: info@sato.pl
www.sato.pl
SATO IBERIA S.A.
Dels Corrals Nous, 35-39
Pol. Can Roqueta, 08202 - Sabadell
Barcelona, Spain
Tel: +34-902-333-341
Fax: +34-902-333-349
Email: info@es.satoeurope.com
www.satoeurope.com
SATO FRANCE S.A.S.
Parc d'Activités, Rue Jacques Messager,
59 175 Templemars, France
Tel: +33-3-20-62-96-40
Fax: +33-3-20-62-96-55
www.satoeurope.com
SATO UK LTD.
Valley Road, Harwich,
Essex CO12 4RR, United Kingdom
Tel: +44-1255-240000
Fax: +44-1255-240111
Email: enquiries@satouk.com
www.satouk.com
American Region
SATO AMERICA, INC.
10350-A Nations Ford Road, Charlotte,
NC 28273, U.S.A.
Tel: +1-704-644-1650
Fax: +1-704-644-1662
www.satoamerica.com
SATO LABELING SOLUTIONS
AMERICA, INC.
1140 Windham Parkway, Romeoville,
Illinois 60446, U.S.A.
Tel: +1-800-645-3290
Fax: +1-630-771-4210
www.satolabeling.com
Download PDF