235 User Manual .pmd - Broadata Communications, Inc.

235 Series
DIGITAL FIBER OPTIC
S-VIDEO/AUDIO/DATA TRANSPORT SYSTEM
BCI reserves the right to make changes to the products described herein without
prior notice or consent. No liability is assumed as a result of their use or
application. All rights reserved.
©2005Broadata Communications, Inc.
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
SAFETY INSTRUCTIONS AND
COMPLIANCE DECLARATIONS
PLEASE OBSERVE THE FOLLOWING SAFETY
PRECAUTIONS AS OUR PRODUCTS CONTAIN
CLASS I LASER PRODUCTS
WARNING
Do not disconnect the fiber optic connector while the unit is powered
up. Exposure to laser radiation is possible when the laser fiber optic
connector is disconnected while the unit is powered up.
Although the fiber optic connectors in this product emit only Class 1
energy that is below the levels considered to be hazardous, one should
never stare directly into a fiber optic connector or an unconnected fiber
end unless one can be certain that no exposure to laser energy could
occur.
CAUTION
This manual is intended for use by trained service personnel. The use
of controls, making adjustments, or performing operations other than
those specified may result in hazardous radiation exposure.
The following label or equivalent is located on the surface of laser products.
This label indicates that the product is classified as a CLASS 1 LASER
PRODUCT.
CLASS 1 LASER PRODUCT
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order
to protect and extend the life of your equipment.
Broadata Technical Support, CustomerService@Broadatacom.com
3
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
TABLE OF CONTENTS
1.0 PRODUCT DESCRIPTION .............................................5
2.0 SETUP .............................................................................. 8
2.1 MOUNTING ......................................................................9
2.2 CABLING AND CONNECTORS ..................................... 9
2.2.1 ELECTRICAL CABLE CONNECTION ......................... 9
2.2.1.1 VIDEO INTERFACE ...................................................9
2.2.1.2 AUDIO INTERFACE ................................................. 11
2.2.1.3 SERIAL DATA INTERFACE ...................................... 13
2.2.2 OPTICAL FIBER CONNECTION ............................... 17
2.3 DC POWER CONNECTION .......................................... 18
3.0 OPERATION ................................................................... 19
4.0 MAINTENANCE AND TROUBLESHOOTING.............. 20
4.1 MAINTENANCE ............................................................. 20
4.2 TROUBLESHOOTING .................................................. 21
5.0 SPECIFICATIONS .......................................................... 23
6.0 SERVICE PROCEDURE ............................................... 25
6.1 REPLACEMENT POLICY ............................................. 25
6.2 RETURN AND REPAIR SERVICE ................................. 25
7.0 LIMITED WARRANTY .................................................... 26
4
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
1.0 PRODUCT DESCRIPTION
The 235 system provides simultaneous transmission of digitized S-video,
stereo audio, and/or data over one or one pair of fibers. Unidirectional
235 system transmits two (2) audios (or one (1) stereo audio pair) and
one (1) baseband S-video channel in one direction. The bi-directional 235
system transmits and receives two (2) audios (or one (1) stereo audio
pair), one (1) baseband S-video channel, and one (1) serial data
(RS-232/RS-422) channel in both directions. The video and audio quality
in the 235 system exceeds professional standards. In addition, the 235
can be configured to transmit two (2) NTSC/PAL video, instead of one (1)
S-video. Many versions of optical transmitter and receiver combinations
are available to address different distance requirements.
The 235 features a digital fiber optic transmission technology, capable of
providing sharp video and crisp audio, with little or no maintenance, high
functionality reliability, and low operating cost. The quality of video, audio
and data transmission in BCI's digital designs is much superior to the
analog transmission designs used by other manufacturers (based on
amplitude or frequency modulation). No user adjustments are required
in the 235 system, enabling quick setup and trouble-free operation.
The 235 comes with two packaging options: a rugged, standalone, and
compact unit, or a plug-in card for a card cage system. Panel connectors
are provided for video (DIN and BNC), audio (terminal block), data (terminal
block), and fiber connection (FC-type for singlemode fiber or ST-type for
multimode fiber). They are also easily monitored by separate LED
indicators for power, optical link, and channel activity.
Due to its digital transmission design, the 235 is capable of addressing
a variety of non-standard configurations. Note that Figures 1-1 and 1-2
illustrate the various 235 models.
Broadata Technical Support, CustomerService@Broadatacom.com
5
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
235R
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
A
RX
D-IN
PWR
LINK
2
D-OUT
D
VIDEO
1
1
2
235T
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
A
TX
2
D-OUT
D
VIDEO
1
D-IN
PWR
1
2
12VDC
Figure 1-1
235-T/R Front/Rear Panels
6
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
235T
235R
A
TX
1
2
D-IN
PWR
L
+ -+ -R
AUDIO
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
D
D-OUT
D
VIDEO
A
RX
D-IN
PWR
1
2
LINK
VIDEO
1
2
D-OUT
DATA
S-VIDEO
I + -+ -- O
1
2
12VDC
Figure 1-2
235-TRX Front/Rear Panels
Broadata Technical Support, CustomerService@Broadatacom.com
7
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
2.0 SETUP
The BCI 235 Series units are used in pairs. One 235-T transmitter unit
is located at the near-end and connected through one optical fiber, to
the 235-R receiver located at the far-end of the link. For the 235-TRX,
equal transceivers are located at both near-end and far-end locations
and connected through two optical fibers. Connections are one to one
between both units. For WDM applications, the 235-TRX units are
configurable for one fiber connectivity. Figures 2-1 and 2-2 depict typical
installations for the 235-T/R and 235TRX, respectively.
Figure 2-1
235-T/R Setup
Figure 2-2
235-TRX Setup
8
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
2.1 Mounting
Before installing the units into your housing, make sure there is
enough space to pull and connect both the electrical and optical
cables without stressing them beyond the manufacturer’s
limitations (also known as the minimum bend radius).
2.2 Cabling and Connectors
In order to setup the BCI 235 properly, make sure to observe
the following instructions when installing the proper cables. The
235 requires two parts to the cabling setup: the electrical and
the optical.
2.2.1 Electrical Cable Connection
The three available cable connections on the electrical side are
for video, audio and data connections. Follow the proceeding
instructions in order to properly install your electrical
connections.
2.2.1.1 Video Interface
The 235 is capable of receiving and transmitting one baseband
S-video signal unidirectionally/bi-directionally, respectively. The
video signals are connected through an S-video cable (e.g.,
RG59U). Use the following procedure for installing video devices.
For the near-end TX unit, connect and label one S-video cable
to the user’s video source connector labeled “VIDEO OUTPUT”
(e.g., camera) and connect the other end of the cable to the
235 “S-VIDEO” connector. (See Figure 2-3). Note that the
user can also connect two NTSC/PAL sources through “Video
1 and 2” BNC connectors.
Broadata Technical Support, CustomerService@Broadatacom.com
9
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
235T
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
A
TX
2
D-OUT
D
VIDEO
1
D-IN
PWR
1
2
235R
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
A
RX
2
D-OUT
D
VIDEO
1
D-IN
PWR
LINK
1
2
Figure 2-3
Cable Connections for the Video Port
10
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
2.2.1.2 Audio Interface
The audio interface supports two channel high fidelity
transmissions. Two separate mono channels or one stereo
channel is transmitted in each direction. Line-level audio signals
are connected to the 235 units using twisted pair shielded cable.
The following steps illustrate the installation procedures for audio
devices.
To send audio signals, on the TX module, at the
near-end location, label and connect two twisted pair shielded
cables to the “AUDIO OUTPUT” connectors of the line level
audio source. On the 235, connect the other end of the cables
to the front panel terminal block connectors labeled “AUDIO
IN”. For stereo channels, be sure to match the cables at both
ends (L to L, R to R), and make sure the connections mate with
the correct polarities (+ to +, - to -). (See Figure 2-4).
To receive audio signals, on the RX module, at the far-end
location, label and connect two twisted shielded pair cables to
the “AUDIO INPUT” connectors of the line level audio receiver.
On the 235, connect the other end of the cables to the front
panel terminal block connectors labeled “AUDIO OUT”. If using
stereo channels, be sure to match the cables at both ends
(L to L, R to R), and make sure the connections mate with the
correct polarities (+ to +, - to -).
Broadata Technical Support, CustomerService@Broadatacom.com
11
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
235T
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
A
TX
2
D-OUT
D
VIDEO
1
D-IN
PWR
1
2
TX
Audio
L
R
L
R
RX
Audio
Figure 2-4
Cable Connections for the Audio Port
12
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
2.2.1.3 Serial Data Interface (235-TRX Series only)
Each 235-TRX unit can be used for either a RS-232 or RS-422
interface, not both simultaneously.
RS-232 unbalanced data
The 235 transmits unbalanced data signals. Follow the
procedures for installing data terminal devices. (See Figure 2-5).
RS-232
OUT
IN
1
2
1
2
Figure 2-5
Cable Connections for the Data Port
1. For the near-end, label and connect one serial computer
data cable to the user’s RS-232 device.
2. Connect the other end of this cable to the front panel RS-232
terminal block connector on the 235-TRX.
3. At the far-end, label and connect one serial computer data
cable to the remote RS-232 device.
4. Connect the other end of this cable to the front panel RS-232
terminal block connector on the far-end 235-TRX unit.
Broadata Technical Support, CustomerService@Broadatacom.com
13
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
Figure 2-6 shows pin connections between the 235-TRX unit (as
a DCE unit) and the user’s RS-232 device (as a DTE unit).
5 4 3 2 1
9 8 7 6
DCE
(BCI 235-TRX unit)
DTE
(User’s RS-232 unit)
Pin
Name
1 Data Carrier Detect (DCD)
2 Receive Data (RX)
3 Transmit Data (TX)
4 Data Terminal Ready (DTR)
5 Signal Ground
Pin
Name
6 Data Set Ready (DSR)
7 Request to Send (RTS)
8 Clear to Send (CTS)
9 Ring Indicator (RI)
RS-232 9-Pin D-Sub Pin Name (DTE)
Figure 2-6
Pin Connections Between 235-TRXUnit
and User’s RS-232 Device
14
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
RS-422 differential serial data
The 235 transmits differential data signals compatible with Full
Duplex RS-422 electrical signals. Note that the RS-422 does
not support handshaking control signals. Use the following
steps for data transmission.
1. For the near-end, label and connect one serial computer
data cable to the user’s RS-422 device.
2. Connect the other end of this cable to the front panel RS-422
female pin connector on the 235.
3. At the far-end, label and connect one serial computer data
cable to the remote RS-422 device.
4. Connect the other end of this cable to the front panel RS-422
terminal block connector on the far-end 235 unit.
Figure 2-7 shows pin connections between the 235 unit (as a
DTE unit) and the user’s RS-422 device (as a DCE unit).
Broadata Technical Support, CustomerService@Broadatacom.com
15
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
DCE
(BCI 235-TRX unit)
5 4 3 2 1
9 8 7 6
DTE
(User’s RS-232 unit)
Pin
Name
1 Not Used
2 Not Used
3 Not Used
4 Not Used
5 Signal Ground
Pin
6 TX+
7 TX8 RX+
9 RX-
Name
Differential
Transmit Data
Differential
Receive Data
Figure 2-7
Pin Connections Between 235 and User’s RS-422 Device
16
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
2.2.2 Optical Fiber Connection
Most cable manufacturers identify individual fibers in the fiber
cable. Select an appropriate terminated fiber. Each unit’s optical
ports in the system are specified for use with Multimode
(62.5/125 micron) fiber, or Singlemode (9/125 micron) fiber.
Follow the ensuing instructions on installing and connecting
the fiber optic links:
1. Ensure the power is off before proceeding with the fiber
optic cable installation.
2. Prior to connecting the fiber optic cables, remove and save
the dust caps from the optical port of both the 235 units.
Clean the fiber optic connector and use a lint-free cloth
dampened with alcohol to thoroughly wipe the side and end
of the ferrule. Use Table 1 as a guideline when connecting
ST and FC connectors.
3. Cross-connect the fibers from one unit to the other
connecting the near end 235 unit’s optical TX port to the far
end 235 unit’s optical RX port as illustrated in Figure 2-8.
235T
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
A
TX
VIDEO
1
2
D-OUT
D
D-IN
PWR
1
2
235R
I
DATA
S-VIDEO
+ -+ -- O
L
+ -+ -R
AUDIO
A
RX
VIDEO
1
2
D-OUT
D
D-IN
PWR
LINK
1
2
Figure 2-8
Fiber Optic Connection
Broadata Technical Support, CustomerService@Broadatacom.com
17
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
Connector
Illustration
Hold the connector by the strain-relief boot* and insert
the connector ferrule into the port. Rotate the boot until
the "key" engages in the slot of the coupling. Push the
c o nne c t o r ho us i ng f o r w a r d unt i l i t c a n b e t ur ne d
clockwise to latch to the port.
*
ST
*
FC
Description
Hold the connector by the strain-relief boot* and insert
the connector ferrule into the port. Rotate the boot until
the "key" engages in the slot of the coupling. Push the
connector housing forward and screw clockwise until it
is tight.
Table 1
Fiber Optic Connector Legend
2.3 DC Power Connection
Congratulations! You are now ready to power up the BCI 235 and set up
your network connection. In order to make sure that you have a proper
installation, please observe the following:
1. Your AC jack has power.
2. The 12VDC power supply is working.
3. Your electrical system has proper grounding (this ensures
that your power supply does not suffer from voltage
variations).
4. Power Surge Protection. This is optional, but highly
recommended. A UPS system provides voltage regularity
as well as prevents spikes from occurring, thus protecting
your 235 from sensitive voltage conditions.
18
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
The 235 derives power from an external 12VDC power supply. This
power supply is a wall mounted AC/DC adapter, 100-240 VAC, 50-60 Hz,
at 1A. This poer supply comes standard for the 235 unless otherwise
specified.
To provide power to the 235, simply connect the power cord, already
provided with the units, and connect it to the wall jack. (You will find one
power cord per unit). Once the power cord has been connected to the
wall jack, connect 12VDC to the unit and the unit should power up
immediately.
If you have any problems or concerns, regarding the installation, make
sure that you have taken the proper steps to ensure a proper power
connection. Otherwise, feel free to contact us for any questions you
may have.
3.0 OPERATION
After the installation procedure is completed, the units are ready for
operation. To operate the BCI 235 units, simply apply power as indicated
in the previous step. Note that the front panel link status indicator,
shown in Table 2, Section 4.1, will be activated.
Broadata Technical Support, CustomerService@Broadatacom.com
19
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
4.0 MAINTENANCE AND TROUBLESHOOTING
4.1 Maintenance
There is no operator maintenance other then keeping the units
clean. However, observe the following light indicators to make
sure that the unit is working properly:
L ab el
Function
Description
L
Audio-L
This GREEN LED indicates L-channel
input audio activity (TX)/L-channel output
audio activity (RX)
R
Audio-R
This GREEN LED indicates R-channel
input audio activity (TX)/R-channel output
audio activity (RX)
S-Video
S-Video
This GREEN LED indicates S-Video
input signal is present (TX)/S-Video
output signal is present (RX)
1
Video 1
This GREEN LED indicates channel-1
composite video input is present
(TX)/channel-1 composite video output is
present (RX)
2
Video 2
This GREEN LED indicates channel-2
composite video input is present
(TX)/channel-2 composite video output is
present (RX)
D-IN
Data In
This GREEN LED indicates input data
activity
D-OUT
Data Out
This GREEN LED indicates output data
activity
LINK
Link
This GREEN LED indicates optical link
is present and established
PWR
P o w er
This RED LED indicates that power is
present
Table 2
Status Indicators
20
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
4.2 Troubleshooting
If the BCI 235 units do not operate properly after installation,
check for: possible cable breaks, loose connections, and
incorrect cable connections. If a problem exists on the fiber
link, please check your fiber connectors for improperly cleaned
fiber cables and connectors. If problems persist that may be
fiber related, contact BCI at 1-800-214-0222 for further
assistance.
For electrical problems, perform the following troubleshooting
procedures:
1. If the POWER indicator is OFF, check for the following:
a. The line cord is plugged into the unit and your outlet
has power.
2. If the POWER indicator is ON, but the Optical Link
indicator is OFF, check for the following:
a. Make sure the appropriate (Singlemode or Multimode)
fibers are being used.
b. Fiber and fiber connectors are not broken. Ensure that
the optical loss does not exceed the specified optical
power attenuation (see Section 5.0 Specifications for
the optical power budget).
c. For each unit, the transmit (TX) fiber is connected to
the other unit’s receiver (RX).
3. If the POWER indicator and Optical Link indicator are
ON, but the audio/video channels are not operating,
then:
a. Check to see that the attached user equipment is turned
on.
b. Both ends of the link are connected to the
corresponding equipment and to the same
corresponding channel port.
Broadata Technical Support, CustomerService@Broadatacom.com
21
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
c. Cable connections at both the video/audio channels
are securely fastened to each connector. Turn the
power off, then back on to reset the link.
d. Output levels of the user’s video and audio sources are
not above the allowed input levels of the 235 units (see
Section 5.0 Specifications).
22
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
5.0 SPECIFICATIONS
Video
Channel Capacity
1
Bandwidth
8 MHz
Video Level
1.2Vp-p @ 75 Ohms
Differential Gain
<1%
Differential Phase
<0.7o
SNR (Weighted)
>70dB
Connector
S-Video or BNC
Audio
Channel Capacity
2
Operating Mode
Balanced or Unbalanced
Input/Output Impedance
600/600 Ohms (Balanced)
Max. Input/Output Level
+10dBm @ 600 Ohms
(Balanced)
Freq. Response
20kHz to 20kHz
THD+N
>85dB @ 1kHz (Balanced)
Connector
Terminal Block
Serial Data
Channel Capacity
1
Signal Format
Operating Mode
RS-232 or RS-422
Full Duplex with Handshake
Data Rate
Up to 115.2kbps (RS-232)
Up to 384kbps (RS-422)
Connector
Terminal Block
Broadata Technical Support, CustomerService@Broadatacom.com
23
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
Physical
Dimension: (H x W x D)
Standalone/external power
Card-cage plug-in card
Unidirectional:
1.72” x 4.36” x 8.75”
Bi-directional:
1.72” x 8.6” x 12.0”
5.24'' x 0.94'' x 11.6''
Power
Standalone/external power
12VDC @ 1 A
Operating Temperature
0 to +50oC
Humidity
0 to 95% RH,
non-condensing
Status Indicators
Power, Optical Link,
Video/Audio/Data Activity
Optical
Fiber Type
Multimode and Singlemode
Number of Fibers
2 or 1
Wavelength
1310 and/or 1550 nm
Fiber Optic Connector
ST (Multimode)
FC (Singlemode)
Typical Power Budget and Transmission Distance
Application
Typical
Power
Distance
Budget (1)
KM (2)
Typical
Distance
Miles (2)
Multimode Fiber
12
3
1.8
Singlemode Fiber
12
25
16
Singlemode Long Distance
20
60
37
(1) These are typical values for the 235 Series. The actual values may vary.
(2) These are typical distance coverage figures. The maximum distance coverage may be
greater than these typical numbers, depending on fiber type, fiber bandwidth, connector
splicing losses, chromatic dispersion, environmental factors, etc.
24
Broadata Technical Support, (800) 214-0222
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
6.0 SERVICE PROCEDURE
6.1 Replacement Policy
Standard products found defective on arrival (DOA) will be
replaced, based on availability, within 24 to 48 hours anywhere
in the U.S. Please call Customer Service at 800-214-0222 for
information.
6.2 Return/Repair Service
The BCI 235 System contains no user serviceable components.
If you have a problem with your unit, please contact the
Customer Service Department. To facilitate our return/repair
processing please contact Broadata Communications, Inc. to
obtain a Return Material Authorization (RMA). Please include
the following information:
•
•
•
•
Product model number
Serial Number
Complete description of problem
Hardware installation description
Broadata Communications, Inc.
2545 West 237th Street, Suite K
Torrance, CA 90505
1-800-214-0222
(310) 530-1416
(310) 530-5958 (Facsimile)
e-mail: CustomerService@Broadatacom.com
Website: www.broadatacom.com
Broadata Technical Support, CustomerService@Broadatacom.com
25
BCI 235 User’s Manual
Digital Fiber Optic S-Video/Audio/Data Transport System
7.0 LIMITED WARRANTY
Broadata Communications, Inc. (BCI) warrants, for a period of one year
from date of shipment, each product sold shall be free from defects in
material and workmanship. BCI will correct, either by repair, or at BCI’s
election, by replacement, any said products that in our sole discretion
prove to be defective and are returned to the manufacturing location
within 30 days after such defect is ascertained. All warranties are limited
to defects arising under normal use and do not include malfunctions or
failure resulting from misuse, abuse, neglect, alterations, electrical power
problems, usage not in accordance with product instructions, improper
installation, or damage determined by BCI to have been caused by the
Buyer or repair made by a third party. Limited warranties granted on
products are to the initial customer end-user and are not transferable.
OUR LIABILITY UNDER THIS WARRANTY SHALL IN ANY CASE BE
LIMITED TO THE INVOICE VALUE OF THE PRODUCT SOLD AND BCI
SHALL NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES ARISING FROM THE USE OF ITS PRODUCTS
OR THE SALE THEREOF. We make NO WARRANTY AS TO THE
MERCHANTABILITY OF ANY GOODS, OR THAT THEY ARE FIT FOR
ANY PARTICULAR PURPOSE OR END APPLICATION NOR DO WE
MAKE ANY WARRANTY, EXPRESSED OR IMPLIED OTHER THAN
AS STATED ABOVE.
26
Broadata Technical Support, (800) 214-0222
Broadata Communications, Inc.
2545 West 237th Street, Suite K
Torrance, CA 90505
1-800-214-0222
(310) 530-1416
(310) 530-5958 (Facsimile)
e-mail: CustomerService@Broadatacom.com
Website: www.broadatacom.com
60000-0235-A1
Download PDF