PoE Industrial Ethernet Extender IVC

PoE Industrial Ethernet Extender IVC
PoE Industrial Ethernet Extender
IVC-2004PT
User’s Manual
Trademarks
Copyright © PLANET Technology Corp. 2010
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. The
information in this manual is subject to change without notice. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or fitness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful interference to
radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances in
electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
PoE Industrial Ethernet Extender User's Manual
For Model: IVC-2004PT
Rev 1.0 (Nov., 2010)
Part No.: 2350-AH0350-000
Table Of Contents
1. Introduction............................................................................... 5
1.1 Checklist............................................................................. 5
1.2 Ethernet over VDSL2 Bridge Description................................ 5
1.3 Key Features....................................................................... 7
1.4 Specifications...................................................................... 8
2. Hardware Description.................................................................11
2.1 Front Panel........................................................................11
2.1.1 LED indicators for IVC-2004PT...................................12
2.1.2 DIP Switch Indication................................................13
2.2 The Upper Panel.................................................................14
3. Installation ..............................................................................15
3.1 Install PoE Industrial Ethernet Extender – IVC-2004PT...........15
3.2 IVC-2004PT BNC / RJ-11 Proper Connection.........................16
3.3 IVC-2004PT Application Connection......................................17
3.4 Wiring the Power Inputs......................................................20
3.5 Wiring the Fault Alarm Contact............................................21
3.6 Mounting Installation...........................................................22
3.6.1 Install DIN-Rail Mounting...........................................22
3.6.2 Wall Mount Plate Mounting........................................24
4. Troubleshooting.........................................................................25
5. FAQ.........................................................................................26
1. Introduction
1.1 Checklist
Check the contents of your package for following parts:
l The PoE Industrial Ethernet Extender x1
l User’s Manual x1
l DIN Rail Kit
l Wall Mount Kit
If any of these items are missing or damaged, please contact your
dealer immediately, if possible, retain the carton including the original
packing material, and use them against to repack the product in case
there is a need to return it to us for repair.
1.2 Ethernet over VDSL2 Bridge Description
PLANET’s state-of-the-art Ethernet-over-VDSL2 products are based on
two core networking technologies: Ethernet and VDSL2 (Very-highdata-rate Digital Subscriber Line 2). This technology offers the
absolute fastest possible data transmission speeds over existing copper
telephone lines or coaxial cables without the need for rewiring.
The IVC-2004PT PoE Industrial Ethernet Extender has a switching
architecture with 4 PoE of RJ-45 10/100Mbps ports and Asymmetric or
Symmetric Ethernet over VDSL port (Asymmetric means upstream and
downstream rate are not the same and Symmetric means upstream
and downstream rate are similar) – the VDSL port can be RJ-11 or
BNC Connector. The IVC-2004PT can set to Master or Slave mode via
a DIP switch. When IVC-2004PT (RJ-11) is connected with other IVC2004PT device, the performance will up to 99/63Mbps for asymmetric
data rate within 200m and up to 28/2Mbps at 1.4km. The IVC-2004PT
(BNC) performance is up to 99/65Mbps for asymmetric data rate within
200m and up to 31/4Mbps at 2.4km. This capability is ideal for use as
an Ethernet extender for your existing Ethernet network.
With 4 PoE interfaces, the IVC-2004PT will be the ideal for small
business and workgroups requiring to deploy the PoE for the wireless
access points, IP-based surveillance camera or IP phones in any places
easily, efficiently and cost effective.
The IVC-2004PT PoE Industrial Ethernet Extender with IP-30 Aluminum
metal shape for easily deployment in Heavy Industrial demanding
environments.
PLANET PoE Industrial Ethernet Extender provides a lower cost
replacement and smooth migration for existing Long Reach Ethernet
(LRE) networks.
The cable specifications of the connection are listed as following:
l 10Base-T, Category 3, 4 or 5 UTP
l 100Base-TX, Category 5, 5e or 6 UTP
l Ethernet over VDSL2, Twisted-pair Telephone Wires
l Ethernet over VDSL2, Coaxial Cable
Note
Slave device (CPE) must connect to Master device (CO)
through the telephone wire or coaxial cable. It is not
allow connecting like Master to Master or Slave to Slave.
To define the IVC-2004PT to Master or Slave, please
refer to section 2.1.2 for more detail.
1.3 Key Features
The PoE Industrial Ethernet Extender provides the following key
features:
l 4 x Ports IEEE 802.3af Power over Ethernet Standard
l Each of PoE port provides 15.4 Watts
l Compatible with IVC-2002, VC-201A and VC-202A (17a Profile)
l Cost-effective VDSL2 Master / Slave bridge solution via DIP Switch
l -40 to 75 Degree C operating temperature
l Redundant Power Design: 12V ~ 48V DC, redundant power with
polarity reverse protect function
l IP-30 Aluminum metal case Protection
l Defines Asymmetric (Band Plan 998) and Symmetric band plans for
the transmission of Upstream and Downstream signals
l Complies with IEEE 802.3, IEEE 802.3u and IEEE 802.3x standards
l DMT (Discrete Multi-Tone) line coding
l Half Duplex Back Pressure and IEEE 802.3x Full Duplex Pause Frame
Flow Control
l Support up to 1536 bytes packet size, 802.1Q VLAN tag transparent
l Integrated
addresses
address
look-up
engine,
support
2K
absolute
MAC
l VDSL2 Stand-Alone transceiver for simple bridge modem application
l Selectable Target Band Plan and Target SNR Margin
l Support extensive LED indicators for network diagnostics
l DIN Rail and Wall Mount Design
1.4 Specifications
Product
IVC-2004PT
Hardware Specification
10/100 Base-TX 4 x RJ-45, Auto-Negotiation and Auto-MDI/MDI-X
Ports
PoE
4 x PoE (Port1 ~ Port4)
VDSL
1 x RJ-11, female Phone Jack
1 x BNC, female connector
DIP Switch
4 position DIP switch
Functionality
Master / Slave mode select
Selectable Fast and Interleaved mode
Selectable target Band Plan
Selectable target SNR mode
Encoding
VDSL-DMT
- ITU-T G.997.1
- ITU-T G.993.1 VDSL
- ITU-T G.993.2 VDSL2 (Profile 17a Support)
LED Indicators
P1 (Green)
P2 (Green)
Fault (Green)
Master (Green) and Slave (Green)
ACT (Green)
Sync. (Green)
PoE (Orange)
Power
Over
PoE Standard
IEEE 802.3af Power over Ethernet / PSE
PoE Type
End-Span
PoE Power
Input
48V DC power input source
PoE Power
Output
48V DC Per Port, 350mA. Max. 15.4 Watts
PoE Pin
Assignment
1/2(+), 3/6(-)
Ethernet
•10Base-T: 2-pair UTP Cat.3,4,5 up to 100m
(328ft)
•100Base-TX: 2-pair UTP Cat.5, 5e, 6 up to
100m (328ft)
VDSL(RJ-11)
Twisted-pair telephone wires (AWG24 or better)
up to 1.4km
BNC
50 ohm: RG58A/U, RG58C/U, RG58/U and 75
ohm: RG6 (Distance 2.4km)
Cabling
Asymmetric Mode
VDSL (RJ-11)
200m -> 99/63Mbps
400m -> 91/48Mbps
600m -> 71/32Mbps
800m -> 53/18Mbps
1000m -> 38/8Mbps
1200m -> 33/5Mbps
1400m -> 28/2Mbps
Performance *1
(Down Stream /
Up Stream)
BNC
200m -> 99/65Mbps
400m -> 99/64Mbps
600m -> 97/59Mbps
800m -> 94/51Mbps
1000m -> 84/45Mbps
1200m -> 73/37Mbps
1400m -> 61/28Mbps
1600m -> 54/20Mbps
1800m -> 48/13Mbps
2000m -> 39/9Mbps
2200m -> 35/6Mbps
2400m -> 31/4Mbps
Symmetric Mode
VDSL (RJ-11)
200m -> 91/99Mbps
400m -> 74/79Mbps
600m -> 54/51Mbps
800m -> 38/34Mbps
1000m -> 27/21Mbps
1200m -> 24/15Mbps
1400m -> 21/10Mbps
BNC
200m -> 95/99Mbps
400m -> 92/97Mbps
600m -> 81/82Mbps
800m -> 71/70Mbps
1000m -> 60/57Mbps
1200m -> 50/44Mbps
1400m -> 42/33Mbps
1600m -> 37/27Mbps
1800m -> 29/22Mbps
2000m -> 23/21Mbps
2200m -> 19/17Mbps
2400m -> 19/13Mbps
Dimensions (H x W x D)
135mm x 87.8mm x 50mm
Weight
631g
Power Requirement *2
12 ~ 48V DC,
Redundant power with polarity reverse protection
function
Power Consumption /
Dissipation
41.76 Watts / 142 BTU Max.
Installation
DIN Rail Kit and Wall Mount Ear
Standard Conformance
Stability testing
IEC60068-2-32 (Free Fall)
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
Operating Temperature
-40 ~ 75ºC
Storage Temperature
-40 ~ 85ºC
Operating Humidity
10% to 90%, relative humidity, non-condensing
Storage Humidity
10% to 90%, relative humidity, non-condensing
Regulation Compliance
FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3af Power over Ethernet
IEEE 802.3x Full Duplex Pause frame Flow Control
ITU-T
•G.997.1
•G.993.1 VDSL
•G.993.2 VDSL2 (Profile 17a)
1.The actual data rate will vary on the quality of the copper wire and
environment factors.
2.If power source is lower than 48V DC, the 802.3af PoE function will
not be activated. However, it will not influence the VDSL2 and 4ports TP operation.
10
2. Hardware Description
n IVC-2004PT
The IVC-2004PT provides 4 RJ-45 with PoE, 1 RJ-11 and 1 BNC port
for network line connection. The 4 RJ-45 ports with two different
running speeds – 10Mbps and 100Mbps. It will distinguish the speed of
incoming connection automatically.
This section describes the hardware features of the PoE Industrial
Ethernet Extender. For easier control of the PoE Industrial Ethernet
Extender, familiarize yourself with its display indicators and ports. Front
panel illustrations in this chapter display the unit LED indicators. Before
connecting any network device to the PoE Industrial Ethernet Extender,
read this chapter carefully.
2.1 Front Panel
The units’ front panel provides a simple interface monitoring the PoE
Industrial Ethernet Extender.
n IVC-2004PT Front Panel
P1
P2 FAULT
Slave Master
Sync. ACT
ON
OFF
1 2 3 4
ON
Slave
Fast
Asymm
6dB
Master
Inter
Symm
9dB
BNC
VDSL
RJ-11
LNK/
ACT
1
PoE
In-Use
2
3
4
LNK/ACT
PoE In-Use
IVC-2004PT
Figure 2-1: IVC-2004PT Front Panel
11
2.1.1 LED indicators for IVC-2004PT
On the front panel of rich diagnostic LEDs provide the operating status
of individual port.
n System
LED
Color
Function
P1
Green
Light
Indicate the power 1 has power.
P2
Green
Light
Indicate the power 2 has power.
FAULT
Green
Light
Indicate the either power 1 or power 2 has
no power.
n VDSL / BNC
LED
Color
ACT
Green
Sync
Green
Function
Light
Indicate that the VDSL link is established.
Blink
Indicate that the VDSL link is actively
sending or receiving data over that port.
Light
Indicate that the VDSL link is established.
Fast
Blink
Indicate that the VDSL link is at training
status (about 10 seconds).
Slow
Blink
Indicate that the VDSL link is at idle status.
Master
Green
Light
Indicate the VDSL Bridge is running at
Master mode.
Slave
Green
Light
Indicate the VDSL Bridge is running at
Slave mode.
n 10/100Base-TX with PoE Port
LED
LNK/
ACT
PoE
In-Use
12
Color
Green
Function
Light
Indicate that the port is link up.
Blink
Indicate that the Extender is actively
sending or receiving data over that port.
Off
Indicate that the port is link down.
Orange Light
Indicate the port is providing 48V DC
in-line power. (1-4 ports).
2.1.2 DIP Switch Indication
The PoE Industrial Ethernet Extender provides 4 selective transmission
modes. By switching the transmission modes, you can obtain a best
transmission mode to suit with phone line or BNC quality of distance
connectivity. The following is the summary table of transmission setting,
bandwidth and distance extensibility tested for AWG 24 (0.5mm)
twisted-pair without noise and cross talk.
DIP-1
DIP-2
DIP-3
DIP-4
Mode
Channel
Band Plan
SNR
OFF
Master
Interleave
Symm
9dB
ON (default)
Slave
Fast
Asymm
6dB
n Master / Salve
tMaster (Central Office) – the Master device mode, usually the
Master device will be located at the data center of ISP or enterprise to link to the backbone.
tSlave (Customer Premises Equipment) – the Slave device mode,
usually the Slave device will be located at branch office, home or
remote side as the long reach data receiver. The Slave also can be
connected to the PC, IP Camera or Wireless Access Point.
Note
When the PoE Industrial Ethernet Extender operates at
Slave mode, the DIP switch 2, 3 and 4 are no function.
n Fast and Interleave mode
tFast mode guarantees a minimum end to end latency less than 1
ms.
tInterleaved mode provides impulse noises protection with a duration less than 250 us. Interleaved mode has a maximum end to
end latency of 10m sec.
13
n Band Plan
tUser can switch the Band Plan either Symmetric or Asymmetric
by their own. When Symmetric is selected that provides better
upstream performance, when Asymmetric is selected that provides
better downstream performance. Refer to table above for details.
n Target SNR (Signal Noise Ratio) Margin
tWhen fixed SNR margin is selected, the system will maintain the
SNR margin at 9 dB across all usable loop length.
Note
By default setting, the four DIP switch at “ON” position and operate as “Slave”. For operate as “Master”,
please adjust the DIP 1 switch to “OFF” position. Adjust
other DIP switch setting to fill different network application demand.
Please power off the PoE Industrial Ethernet Extender before making
any transmission mode adjustment.
2.2 The Upper Panel
The upper panel of the PoE Industrial Ethernet Extender consists one
terminal block connector within two DC power inputs.
Figure 2-2 shows the upper panel of the PoE Industrial Ethernet
Extender.
V1- V1+
PWR1
V2- V2+
Fault
PWR2
Input
DC 48V
Figure 2-2 PoE Industrial Ethernet Extender Upper Panel.
14
3. Installation
3.1 Install PoE Industrial Ethernet Extender – IVC-2004PT
The PoE Industrial Ethernet Extender does not require any software
configuration. Users can immediately use any feature of this product
simply by attached the cables and plug power on. There is some key
limitation on the PoE Industrial Ethernet Extender. Please check the
following items:
IVC-2004PT: The device is used for Point-to-Point connection only
(Master device to Slave device) and has equipped with one RJ-11 and
one BNC connector for VDSL2 network connection.
Telephone Wire: Depending on the quality of telephone line, the
maximum distances of RJ-11 segment is 1.4km (4593ft) with AWG 24
telephone wires.
Coaxial: Depending on the quality of coaxial cable, the maximum
distance of BNC segment is 2.4km (7874ft) with 5C type of coaxial
cable.
The link distances and performance will vary on the quality of telephone
wire and coaxial cable.
15
3.2 IVC-2004PT BNC / RJ-11 Proper Connection
PLANET PoE Industrial Ethernet Extender has a DIP switch which can
adjust to be Master or Slave mode. Connection of two PLANET PoE
Industrial Ethernet Extenders, one must be Master (CO) mode and
the other one must be Slave (CPE) mode. Please refer to the following
Figure 3-1 chart.
PoE Industrial Ethernet Extender does not
connecting BNC and RJ-11 at the same time.
Note
P1
ON
P2 FAULT
Slave Master
OFF
ON
Sync. ACT
Coaxial Cable
Connections 2.4km Max.
BNC
Slave
Fast
Asymm
6dB
1 2 3 4
ON
Master
Inter
Symm
9dB
OFF
Master
Inter
Symm
9dB
1 2 3 4
OFF
1 2 3 4
ON
Slave
Fast
Asymm
6dB
ON
ON
Master
Inter
Symm
9dB
1 2 3 4
ON
Slave
Fast
Asymm
6dB
allow
VDSL2
VDSL
No Connection
RJ-11
PoE IP camera
Ethernet Switch
PoE
LNK/
ACT
1
PoE
In-Use
RJ-45 Connections
100m (328ft) Max.
RJ-45 Connections
100m (328ft) Max.
2
3
4
LNK/ACT
PoE In-Use
IVC-2004PT
Slave / IVC-2002
Master / IVC-2004PT
P1
ON
P2 FAULT
Slave Master
OFF
ON
Slave
Fast
Asymm
6dB
1 2 3 4
ON
Master
Inter
Symm
9dB
OFF
1 2 3 4
OFF
1 2 3 4
Slave
Fast
Asymm
6dB
ON
Sync. ACT
ON
Master
Inter
Symm
9dB
ON
1 2 3 4
ON
Slave
Fast
Asymm
6dB
Master
Inter
Symm
9dB
No Connection
BNC
VDSL
RJ-11
PoE IP camera
VDSL2
Telephone Wire
Connections 1.4km Max.
PoE
LNK/
ACT
RJ-45 Connections
100m (328ft) Max.
Ethernet Switch
1
PoE
In-Use
2
RJ-45 Connections
100m (328ft) Max.
3
4
LNK/ACT
PoE In-Use
IVC-2004PT
Master / IVC-2004PT
Slave / IVC-2002
VDSL2
VDSL2 Coaxial Cable
VDSL2
VDSL2 Telephone Wire
PoE
100Base-TX UTP with PoE
100Base-TX UTP
Figure 3-1: Industrial Ethernet Extender BNC and RJ-11 Connection Chart
16
3.3 IVC-2004PT Application Connection
Two PoE Industrial Ethernet Extenders could be used to link two
different Area networks. Through the normal telephone line or
coaxial cable, it could setup 99/63Mbps (RJ-11) or 99/65Mbps (BNC)
asymmetric backbone.
PoE
100Base-TX UTP with PoE
100Base-TX UTP
VDSL2
VDSL2
PoE
PoE IP Camera
PoE
NVR
PoE IP Camera
VDSL2
Coaxial or Phone Wire
PoE
IVC-2004PT
PoE Wireless AP
IVC-2004PT
PoE
PoE IP Phone
LAN 1
* BNC: 2.4km
RJ-11: 1.4km
LAN 2
Figure 3-2: IVC-2004PT BNC and RJ-11 Connection
With 4 PoE, in-line power interfaces, the PoE Industrial Ethernet
Extender can build a power central-controlled IP phone system, IP
camera system, AP group for the enterprise. For instance, 4 camera
/ AP can be easily installed around the corner in the company for
surveillance demands or build a wireless roaming environment in the
offices. Without the power-socket limitation, it makes the installation of
cameras or WLAN AP more easily and efficiently.
17
Data+Power
PoE
PoE
100Base-TX UTP with PoE
DC
Power Line (DC)
Telephone wire
PoE IP Camera
2.4GHz 802.11n
N
48V DC Power Input
IVC-2004PT
DC
DIN-Rail
Power Supply
Data+Power
PoE
PoE VoIP ATA
PoE
PoE
N
N
Phone
PoE VoIP Phone
PoE Wireless AP
Figure 3-3: IVC-2004PT PoE Connection
IVC-2004PT temperature range is from -40 to 75 Degree C which can
handle any harsh environment and places. It also compatibles with
PLANET IVC-2002, VC-201A and VC-202A. Without spend extra cost to
deploy a new local Internet in apartment, hotel, campus and hospitality
environment. It can use the original network structure to re-deploy
with our latest product PLANET IVC-2004PT. For example, MC-700, MC1500 and MC-1500R chassis with VC-201A and VC-202A inside and set
it as CPE (Customer Premises Equipment) mode which placed in
the wiring center (MDF room). On the other hand, connects an IVC2004PT extender with Master mode by using telephone line or
coaxial cable.
18
Switch
1.4km
2.4km
IVC-2004PT Master
VDSL2
IVC-2004PT Master
VDSL2
VC-202A/VC-201A CPE+
MC-700 Chassis
PoE
PoE IP Camera
PoE
PoE IP Camera
VDSL2
Control Center
2.4km
PoE
PoE
IVC-2004PT Master
PoE
PoE IP Camera
PoE IP Camera
PoE IP Camera
Harbor
Steel Factory
PoE
PoE
PoE IP Camera
Railway
100Base-TX UTP with PoE
100Base-TX UTP
VDSL2
VDSL2 Coaxial Cable
VDSL2
VDSL2 Telephone Wire
Figure 3-4: IVC-2004PT Application Topology
When deciding where to put the IVC-2004PT then you must ensure:
tIt is accessible and cables can be connected easily.
tCabling is away from sources of electrical noise such as radios,
transmitters and power lines and fluorescent lighting fixtures.
tAvoid the Water or moisture to reach the IVC-2004PT.
tAir Flow around the unit and through the vents in the side of the
case is not restricted (company recommend that you provide a
minimum of 25mm inch clearance).
To prolong the operational life of your units:
tDo not place objects on top of any unit or stack.
19
3.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of PoE
Industrial Ethernet Extender is used for two DC redundant powers
input. Please follow the steps below to insert the power wire.
1.Insert positive / negative DC power wires into the contacts 1 and 2
for POWER 1, or 5 and 6 for POWER 2.
V1- V1+
PWR1
V1- V1+
Note
20
V2- V2+
Fault
PWR2
Input
DC 48V
V2- V2+
Must input 48V DC power source to make PoE function
workable
2.Tighten the wire-clamp screws for preventing the wires from loosing.
1
2
Power 1
-
3
4
Fault
+
5
6
Power 2
-
+
3.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the PoE
Industrial Ethernet Extender will detect the fault status of the power
failure and then forms an open circuit. The following illustration shows
an application example for wiring the fault alarm contacts.
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in
the range between 12 ~ 24 AWG.
2. Alarm relay circuit accepts up to 30V, max. 3A
currents.
21
3.6 Mounting Installation
This section describes how to install the PoE Industrial Ethernet
Extender and make connection to it. Please read the following topics
and perform the procedures in the order being presented.
Note
In the installation steps below, this Manual use IGS801(PLANET 8 Port Industrial Gigabit Switch) as the
example. However, the steps for PLANET Industrial
Switch & Industrial Media Converter are similar.
3.6.1 Install DIN-Rail Mounting
The DIN-Rail is screwed on the PoE Industrial Ethernet Extender
when out of factory. Please refer to following figures to hang the PoE
Industrial Ethernet Extender on track.
1
2
Step 1: Lightly press the button of DIN-Rail into the track.
22
Step 2: Check the DIN-Rail is tightly on the track.
Step 3: Please refer to following procedures to remove the PoE
Industrial Ethernet Extender from the track.
1
2
Step 4: Lightly press the button of DIN-Rail for remove it from track.
23
3.6.2 Wall Mount Plate Mounting
To install the PoE Industrial Ethernet Extender on the wall, please
follows the instructions described below.
Step 1: Remove the DIN-Rail from the PoE Industrial Ethernet
Extender; loose the screws to remove the DIN-Rail.
Step 2: Place the wall mount plate on the rear panel of the PoE
Industrial Ethernet Extender.
Step 3: Use the screws to screw the wall mount plate on the PoE
Industrial Ethernet Extender.
Step 4: Use the hook holes at the corners of the wall mount plate to
hang the PoE Industrial Ethernet Extender on the wall.
Step 5: To remove the wall mount plate, reverse steps above.
24
4. Troubleshooting
SYMPTOM:
VDSL LNK LED does not light after wire is connected to the VDSL port.
CHECKPOINT:
1.Verify the length of the wires connected between two IVC-2004PT
extenders not more than 2.4km for BNC and 1.4km for RJ-11
connections. Please also try to adjust the DIP switch of IVC-2004PT
to other SNR mode.
2.Please note that you must use one IVC-2004PT with Master mode
and the other IVC-2004PT with Slave mode.
SYMPTOM:
TP LED does not light after cable is connected to the port.
CHECKPOINT:
1.Verify you are using the Cat.5, 5e or 6 cables with RJ-45 connector
to connect to the port.
2.If your device (like LAN card) supports Auto-Negotiation, please try
to modify at a fixed speed of your device by manually.
3.Check the extender and the connected device’s power are “ON”.
4.Check the cables are firmly seated in its connectors in the switch and
in the associated device.
5.Check the connecting cables are good.
6.Check the power adapter is functional, including the connecting
device.
25
5. FAQ
Q1: What is the IVC-2004PT power input?
A1: 48V DC for PoE function and 12 to 36V DC for Non-PoE function
Q2: What is VDSL2?
A2: VDSL2 (Very High-Bit-Rate Digital Subscriber Line 2), G.993.2 is
the newest and most advanced standard of xDSL broadband wire
line communications.
Designed to support the wide deployment of Triple Play services
such as voice, data, high definition television (HDTV) and interactive gaming, VDSL2 enable operators and carrier to gradually,
flexibly, and cost efficiently upgrade exiting xDSL-infrastructure.
Q3: What is the best distance for IVC-2004PT?
A3: In order to guarantee the stability and better quality of network,
so we would suggest the distance within 1.4 kilometer is the best
for RJ-11 Connecting and 2.4 kilometer for BNC Connecting.
Q4: What is the best data rate for IVC-2004PT?
A4:
Link Type & RJ-11 (Telephone Wire)
Distance
200m
1400m
DIP Mode
200m
Asymmetric
99/63Mbps 28/2Mbps
99/65Mbps 31/4Mbps
Symmetric
91/99Mbps 21/10Mbps 95/99Mbps 19/13Mbps
BNC (Coaxial Cable)
2400m
Q5: Can IVC-2004PT compatible with VC-201A / VC-202A?
A5: YES, IVC-2004PT (profile 17a) and VC-201A / VC-202A (profile
17a) are base on ITU-T G.993.2 VDSL2 with same Profiles; so far
they are compatible with each other.
26
Q6: What is SNR and what’s the effect?
A6: In analog and digital communications, Signal-to-Noise Ratio, often
written SNR, is a measure of signal strength relative to background noise. The ratio is usually measured in decibels (dB).
In digital communications, the SNR will probably cause a reduction
in data speed because of frequent errors that require the source
(transmitting) computer or terminal to resend some packets of
data. SNR measures the quality of a transmission channel over a
network channel. The greater the ratio, the easier it is to identify
and subsequently isolate and eliminate the source of noise.
Generally speaking, the higher SNR value gets better line quality,
but lower performance.
Q7: What is band plan and what’s the effect?
A7: VDSL2 defines multiple band plans and configuration modes
(profiles) to allow asymmetric and symmetric services in the
same binder (by designated frequency bands) for the transmission of upstream and downstream signals. User has the ability to
select fixed band plan. When Symmetric is selected that provides
better downstream performance, when Asymmetric is selected
that provides better upstream performance.
27
EC Declaration of Conformity
For the following equipment:
*Type of Product: Industrial Ethernet Extender with 4-Port PoE ( 1 BNC / RJ-11 + 4-Port 10/100TX
*Model Number:
PoE -17a Profile, -40~75 DegreeC)
IVC-2004PT
* Produced by:
Manufacturer‘s Name :
Manufacturer‘s Address:
Planet Technology Corp.
11F, No 96, Min Chuan Road,
Hsin Tien, Taipei, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive
on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
Emission
Harmonic
Flicker
Immunity
ESD
RS
EFT/ Burst
Surge
CS
Magnetic Field
Voltage Disp
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
(Class A: 2006)
(2006)
(1995/A1: 2001/A2:2005)
(1998/A1: 2001/A2:2003)
(2001)
(2008)
(2004)
(2005)
(2008)
(2001)
(2004)
Responsible for marking this declaration if the:
_ Manufacturer
† Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan
Place
22 Oct., 2010
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected]
http://www.planet.com.tw
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement