Manual - Projector Point UK

User's Guide
Organization of the Guide and Notations in the Guide
Using Each Guide
The guides for this projector are organized as shown below.
Safety Instructions/Support and Service Guide
Contains information on using the projector safely, as well as a support and service guide,
troubleshooting check lists, and so on. Make sure you read this guide before using the pro‐
jector.
User's Guide (this guide)
Contains information on setting up and basic operations before using the projector, using
the Configuration menu, and handling problems and performing routine maintenance.
Quick Start Guide
Contains information on the procedures for setting up the projector. Read this first.
3D Glasses User's Guide
Contains information on handling the 3D Glasses and warnings and so on.
WirelessHD Transmitter User's Guide (EH-TW9200W/EH-TW8200W only)
Contains information on handling the WirelessHD Transmitter and warnings and so on.
1
Organization of the Guide and Notations in the Guide
Notations Used in This Guide
Safety Indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The following shows the symbols and their meanings. Please understand and respect these caution symbols
in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death
due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical
damage due to incorrect handling.
General Information Indications
Attention
Indicates procedures which may result in damage or malfunctions to occur.
c
s
Menu Name
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where detailed information regarding a topic can be found.
Indicates Configuration menu items.
Example: Image - Color Mode
Button Name
Indicates the buttons on the remote control or the control panel.
Example:
button
About the Use of "This Product" or "This Projector"
As well as the main projector unit, supplied items or optional extras may be referred to using the phrase "this
product" or "this projector".
2
Contents
Connecting an HDMI Cable Clamp (EHTW9200W/EH-TW9200/EH-TW8200W/EHTW8200 only) . . . . . . . . . . . . . . . . . . . . . . . . . 22
Organization of the Guide and
Notations in the Guide
Using Each Guide . . . . . . . . . . . . . . . . . . . . . 1
Preparing the Remote Control . . . . . . . . 23
Notations Used in This Guide . . . . . . . . . . . 2
Installing the Remote Control Batteries . . . . . . . 23
Safety Indications . . . . . . . . . . . . . . . . . . . . . . . 2
Remote Control Operating Range . . . . . . . . . . . 24
General Information Indications . . . . . . . . . . . . . 2
Operating range (left to right) . . . . . . . . . . . . 24
About the Use of "This Product" or "This Projector"
..................................... 2
Operating range (top to bottom) . . . . . . . . . . 24
Basic Operations
Introduction
Starting and Ending Projection . . . . . . . 25
Projector Features . . . . . . . . . . . . . . . . . . . . 6
Turning on the Projector and Projecting . . . . . . 25
Dynamic 3D Display . . . . . . . . . . . . . . . . . . . . . . 6
If the Target Image is not Projected . . . . . . . . . . 26
Adjusting Images to Suit your Surroundings
(Color Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Turning Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Adjusting the Projected Screen . . . . . . . 27
Absolute Color Adjustment . . . . . . . . . . . . . . . . 6
Displaying the Test Pattern . . . . . . . . . . . . . . . . 27
Conforms to Wireless Transmissions for the
WirelessHD Standards (EH-TW9200W/EHTW8200W Only) . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjusting the Focus . . . . . . . . . . . . . . . . . . . . . 27
Other Useful Functions . . . . . . . . . . . . . . . . . . . . 7
Adjusting the Projection Size (Zoom
Adjustment) . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Part Names and Functions . . . . . . . . . . . . . 8
Adjusting the Projector's Tilt . . . . . . . . . . . . . . . 28
Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Adjusting the Position of the Projected Image
(Lens Shift) . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Correcting Keystone Distortion . . . . . . . . . . . . . 29
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . 11
Hiding the Image Temporarily . . . . . . . . . . . . . . 29
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the Image
Appearance . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjusting the Image . . . . . . . . . . . . . . . . . 30
Preparing
Selecting the Projection Quality (Color Mode)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Various Projection Methods . . . . . . . . . . . . . . . 17
Switching the Screen Between Full and Zoom
(Aspect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Adjusting the Projection Size . . . . . . . . . . . . . . 18
Absolute Color Adjustments . . . . . . . . . . 33
Connecting a Device . . . . . . . . . . . . . . . . . 19
Adjusting Hue, Saturation, and Brightness . . . . . 33
Connecting Video Equipment . . . . . . . . . . . . . . 19
Adjusting the Gamma . . . . . . . . . . . . . . . . . . . 34
Connecting a Computer . . . . . . . . . . . . . . . . . . 20
Select and adjust the correction value . . . . . . 34
Connecting External Devices . . . . . . . . . . . . . . . 20
Adjust while viewing the image (EHTW9200W/EH-TW9200/EH-TW8200W/EHTW8200 only) . . . . . . . . . . . . . . . . . . . . . . . 34
Connecting to the Trigger out port . . . . . . . . 20
Connecting WirelessHD devices (EHTW9200W/EH-TW8200W only) . . . . . . . . . . . 20
Adjust using the gamma adjustment graph
(EH-TW9200W/EH-TW9200/EH-TW8200W/
EH-TW8200 only) . . . . . . . . . . . . . . . . . . . . . 35
Connecting smartphones or tablets (EHTW9200W/EH-TW8200W only) . . . . . . . . . . . 21
Adjusting the RGB (Offset/Gain) . . . . . . . . . . . . 35
Removing the Interface Cover . . . . . . . . . . . . . . 21
Color Temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3
Contents
Skin Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Useful Functions of the WirelessHD Transmitter
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Detailed Image Adjustments . . . . . . . . . . 37
Switching the target image . . . . . . . . . . . . . . 58
Adjusting the Sharpness . . . . . . . . . . . . . . . . . . 37
Switching the image source . . . . . . . . . . . . . 59
Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . 38
Remote control operating range . . . . . . . . . . 60
Frame Interpolation (EH-TW9200W/EHTW9200/EH-TW8200W/EH-TW8200 only) . . . . . . 38
Using the HDMI Link Function . . . . . . . . 61
Super-resolution . . . . . . . . . . . . . . . . . . . . . . . 39
HDMI Link Function . . . . . . . . . . . . . . . . . . . . . 61
Panel Alignment . . . . . . . . . . . . . . . . . . . . . . . 39
HDMI Link Settings . . . . . . . . . . . . . . . . . . . . . . 61
Image Processing . . . . . . . . . . . . . . . . . . . . . . . 40
Device Connections . . . . . . . . . . . . . . . . . . . . . 62
Selecting the Color Gamut (EH-TW9200W/EHTW9200 Only) . . . . . . . . . . . . . . . . . . . . . . . . . 41
Projecting Two Different Images Using
Picture in Picture . . . . . . . . . . . . . . . . . . . . 63
Viewing the Image at the Saved Image
Quality (Memory Function) . . . . . . . . . . . 42
Types of Screen that can be Displayed
Simultaneously . . . . . . . . . . . . . . . . . . . . . . . . 63
Saving Function . . . . . . . . . . . . . . . . . . . . . . . . 42
Projecting on a Picture in Picture . . . . . . . . . . . . 63
Saving a Memory . . . . . . . . . . . . . . . . . . . . . . . 42
Starting Picture in Picture . . . . . . . . . . . . . . . 63
Loading a Memory . . . . . . . . . . . . . . . . . . . . . . 43
Changing the Picture in Picture settings . . . . 64
Deleting a Saved Memory . . . . . . . . . . . . . . . . . 43
Configuration Menu
Renaming a Memory . . . . . . . . . . . . . . . . . . . . 43
Configuration Menu Functions . . . . . . . . 65
Useful Functions
Configuration Menu Operations . . . . . . . . . . . . 65
Enjoying 3D Images . . . . . . . . . . . . . . . . . . 45
Configuration Menu Table . . . . . . . . . . . . . . . . 66
Setting 3D Images . . . . . . . . . . . . . . . . . . . . . . 45
Image menu . . . . . . . . . . . . . . . . . . . . . . . . 66
When the projector detects a 3D format . . . . 45
Signal menu . . . . . . . . . . . . . . . . . . . . . . . . 68
When the projector cannot detect a 3D
format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Settings menu . . . . . . . . . . . . . . . . . . . . . . . 70
Extended menu . . . . . . . . . . . . . . . . . . . . . . 73
If the 3D image cannot be viewed . . . . . . . . . 45
Memory menu . . . . . . . . . . . . . . . . . . . . . . . 75
Using 3D Glasses . . . . . . . . . . . . . . . . . . . . . . . 46
Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Charging the 3D Glasses . . . . . . . . . . . . . . . . 46
Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . 75
Pairing 3D Glasses . . . . . . . . . . . . . . . . . . . . 46
Picture in Picture menu . . . . . . . . . . . . . . . . 76
Wearing the 3D Glasses . . . . . . . . . . . . . . . . 47
Troubleshooting
Range for Viewing 3D Images . . . . . . . . . . . . . . 47
Warnings Regarding Viewing 3D Images . . . . . . 48
Problem Solving . . . . . . . . . . . . . . . . . . . . . 77
Converting 2D Images to 3D and Viewing . . . . . 50
Reading the Indicators . . . . . . . . . . . . . . . . . . . 77
Connecting with WirelessHD (EHTW9200W/EH-TW8200W Only) . . . . . . . . 52
Indicator status during an error/warning . . . . 77
Indicator status during normal operation . . . . 79
Installing the WirelessHD Transmitter . . . . . . . . 52
When the Indicators Provide No Help . . . . . . . . 80
WirelessHD Transmitter part names . . . . . . . . 52
Check the problem . . . . . . . . . . . . . . . . . . . . 80
Setting the WirelessHD Transmitter . . . . . . . . 53
Problems relating to images . . . . . . . . . . . . . 80
Projecting Images . . . . . . . . . . . . . . . . . . . . . . 54
Problems when projection starts . . . . . . . . . . 85
WirelessHD Settings Menu . . . . . . . . . . . . . . . . 56
Problems with the remote control . . . . . . . . . 85
WirelessHD Transmission Range . . . . . . . . . . . . 56
4
Contents
Problems with the control panel . . . . . . . . . . 85
Problems with 3D . . . . . . . . . . . . . . . . . . . . 86
Problems with HDMI . . . . . . . . . . . . . . . . . . 86
Problems with WirelessHD (EH-TW9200W/
EH-TW8200W only) . . . . . . . . . . . . . . . . . . . 87
Maintenance
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 89
Cleaning the Parts . . . . . . . . . . . . . . . . . . . . . . 89
Cleaning the air filter . . . . . . . . . . . . . . . . . . 89
Cleaning the main unit . . . . . . . . . . . . . . . . . 90
Cleaning the lens . . . . . . . . . . . . . . . . . . . . . 91
Cleaning the 3D Glasses . . . . . . . . . . . . . . . . 91
Replacement Periods for Consumables . . . . . . . 91
Air filter replacement period . . . . . . . . . . . . . 91
Lamp replacement period . . . . . . . . . . . . . . 91
Replacing Consumables . . . . . . . . . . . . . . . . . . 92
Replacing the air filter . . . . . . . . . . . . . . . . . 92
Replacing the lamp . . . . . . . . . . . . . . . . . . . 93
Resetting lamp hours . . . . . . . . . . . . . . . . . . 94
Appendix
Optional Accessories and
Consumables . . . . . . . . . . . . . . . . . . . . . . . . 96
Optional Items . . . . . . . . . . . . . . . . . . . . . . . . . 96
Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Supported Resolutions . . . . . . . . . . . . . . . 97
Component Video . . . . . . . . . . . . . . . . . . . . . . 97
Composite Video . . . . . . . . . . . . . . . . . . . . . . . 97
Computer Signals (Analog RGB) . . . . . . . . . . . . 97
HDMI1/HDMI2 Input Signal . . . . . . . . . . . . . . . . 97
3D Input Signal . . . . . . . . . . . . . . . . . . . . . . . . 98
WirelessHD Input Signal . . . . . . . . . . . . . . . . . . 98
3D Input Signal MHL (via a WirelessHD
Transmitter*) . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Specifications . . . . . . . . . . . . . . . . . . . . . . 100
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
General Notes . . . . . . . . . . . . . . . . . . . . . . 105
General Notice . . . . . . . . . . . . . . . . . . . . . . . . 106
5
Introduction
Projector Features
Dynamic 3D Display
Enjoy 3D contents on Blu-ray and images filmed with a 3D camera through a stunning projection display.
s p.45
You can also convert standard 2D images into 3D images. s p.50
Adjusting Images to Suit your Surroundings (Color Mode)
By simply selecting the Color Mode, you can project the optimum image to suit your surroundings. s p.30
Setting Example
Living Room
For use in a bright room
Cinema
For movies and concerts in a dark room
Absolute Color Adjustment
As well as using Color Mode, you can also adjust the color temperature of the image and skin tones to suit
your taste. s p.35
What's more, you can obtain colors that match the image and achieve the colors you want through a
combination of gamma adjustment, RGB offset or gain adjustment for each color, and hue, saturation, and
brightness adjustment for each RGBCMY color. s p.33
6
Introduction
Conforms to Wireless Transmissions for the WirelessHD Standards (EH-TW9200W/EHTW8200W Only)
The projector can wirelessly receive data for images from WirelessHD compatible AV devices. You do not
need to connect a cable directly to the main projector unit.
You can connect up to five AV devices to the WirelessHD Transmitter at the same time, and switch images
using the remote control.
You can also connect other output devices such as televisions, and switch the device. This allows other output
devices to project images from the connected AV device, even if the projector is off. s p.52
Projector
Transmitter
Multi-media players, game consoles,
and so on
You can also connect MHL compatible smartphones or tablets with an MHL compatible cable. s p.21
Other Useful Functions
In addition, the following useful functions are provided.
• The remote control contains a backlight function allowing for easy use even in dark rooms. Operations are also
button. s p.11
simplified by only pressing the
• Lens shift allows you to adjust the projection position when the projector cannot be setup directly in front of the
screen. The ability to move the projection position up, down, left, and right from in front of the screen without
changing the projection range, gives you more freedom to place the projector where you want. s p.28
• The Frame Interpolation function creates an intermediary image between one frame and the next rendering a
smoother, cleaner viewing experience, and removing jarring movements such as frame skipping. (EH-TW9200W/EHTW9200/EH-TW8200W/EH-TW8200 only) s p.38
• The Super-resolution function allows you to enjoy DVDs in high resolution. Also, low resolution areas (parts that are
blurred) of full hi-vision images become smoother and sharper. s p.39
7
Introduction
Part Names and Functions
Front/Top
Name
Function
a Lamp cover
b Lens shift dial
Open when replacing the projector's lamp. s p.93
c Air exhaust vent
Exhaust vent for air used to cool the projector internally.
Adjusts the position of the projected image. s p.28
Caution
While projecting, do not put your face or hands near the air exhaust vent,
and do not place objects that may become warped or damaged by heat near
the vent. Hot air from the air exhaust vent could cause burns, warping, or
accidents to occur.
d Remote receiver
e Lens shutter
Receives signals from the remote control. s p.24
f Projector's lens
g Air filter cover
Images are projected from here.
Air intake vent
Closes automatically when the projector is turned off to protect the lens from
being scratched or soiled. s p.25
When cleaning or replacing the air filter, open this cover and remove the air filter.
s p.89, p.92
Intake vent for air used to cool the projector internally.
h Front adjustable foot When setup on a surface such as a table, extend the foot to adjust the horizontal
tilt. s p.28
i Control panel
Control panel on the projector. Open the control panel cover to perform opera‐
tions. s p.9
j Focus ring
k Zoom ring
Adjusts the image focus. s p.27
Adjusts the image size. s p.28
8
Introduction
Control Panel
Buttons/Indicators
Function
a
Flashes to indicate warm-up in progress or cool-down in progress. Shows the
projector's status through a combination of other indicators lit and flashing.
s p.77
b
Flashes orange when it is time to replace the lamp. Shows the projector's errors
through a combination of other indicators lit and flashing. s p.77
c
Flashes orange if the internal temperature is too high. Shows the projector's
errors through a combination of other indicators lit and flashing. s p.77
d
Displays and closes the Configuration menu.
On the Configuration menu, you can make adjustments and settings for Signal,
Image, Input Signal, and so on. s p.65
e Control panel cover
Cover for the control panel. When you want to use the control panel, grip the
knob and slide the cover open.
f
Selects the adjustment value for the keystone correction and for menu items.
s p.29
g
Selects adjustment values for menu items. s p.65
h
Returns to the previous menu level when a menu is displayed. s p.65
i
Selects functions and settings when a menu is displayed. s p.65
9
Introduction
Buttons/Indicators
Function
j
Changes to the image from each input port. s p.26
k
Turns the projector power on or off. s p.25
Lit when the projector is on. Shows the projector's errors through a combina‐
tion of other indicators lit and flashing. s p.77
10
Introduction
Remote Control
Button
Function
a
Turns the projector on. s p.25
b
Allows you to simultaneously project two im‐
age sources, one in the main screen and the
other in the sub screen. (Picture in Picture)
s p.63
Press and hold the button to swap the main
or sub screen image sources.
c
Changes to the image from each input port.
s p.26
button is only available for EHTW9200W/EH-TW8200W.
d
This button displays the settings menu for
HDMI Link.
With the other buttons, you can then start or
stop playback, and so on for connected devi‐
ces that meets the HDMI CEC standards.
s p.61
e
Changes between 2D and 3D. s p.45
f
Selects menu items and adjustment values.
s p.65
g
The adjustment value returns to its default
value when pressed while the menu's adjust‐
ment screen is displayed. s p.65
h
Displays and closes the Configuration menu.
On the Configuration menu, you can make
adjustments and settings for Signal, Image,
Input Signal, and so on. s p.65
i
Sets Auto Iris. s p.38
j
Performs the function assigned to the user
button. s p.70
k
Saves, loads, or erases a memory. s p.42
11
Introduction
Button
l
Function
(Only available for EH-TW9200W/EHTW8200W)
WiHD Transmitter control
Turns on the WirelessHD Transmitter, or
switches the input and output.
Make sure you point the remote control at the
WirelessHD Transmitter when performing
operations. s p.52
m
Displays and closes the test pattern. s p.27
n
Changes the 3D format.
This projector supports the following 3D for‐
mats.
• Frame Packing
• Side by Side
• Top and Bottom
s p.45
o
(Only available for EH-TW9200W/EHTW9200/EH-TW8200W/EH-TW8200)
Reduces the jarring effect caused by quick
movements by interpolating frames, and ad‐
justs to render a smoother, clearer image.
s p.38
p
Selects the aspect mode according to the in‐
put signal. s p.31
q
Adjusts the hue, saturation, and brightness
for each RGBCMY color. s p.33
r
Returns to the previous menu level when a
menu is displayed. s p.65
s
When a menu is displayed, it accepts and en‐
ters the current selection and moves to the
next level. s p.65
t
Set Super-resolution to reduce blurring in
areas such as the edges of the image.
s p.39
A
Changes the Color Mode. s p.30
B
Adjusts the volume for connected devices
that meet the HDMI CEC standards.
C
Temporarily hides or shows the image.
s p.29
D
The remote control buttons light up for ap‐
proximately 10 seconds. This is useful when
operating the remote control in the dark.
12
Introduction
Button
E
Function
Turns the projector off. s p.26
13
Introduction
Rear
Name
Function
a Cable holder
Thick HDMI cables with a large outer diameter and so on, may disconnect
easily due to the weight of the cable. To prevent the cable from disconnecting,
fix it in place using the HDMI cable clamp supplied (EH-TW9200W/EHTW9200/EH-TW8200W/EH-TW8200 only). s p.22
b HDMI1 port
c HDMI2 port
Connects HDMI compatible video equipment and computers. s p.19
d Component port
Connects to the component (YCbCr or YPbPr) output port on video equip‐
ment. s p.19
e Video port
f PC port
Connects to the composite video output port on video equipment. s p.19
g RS-232C port
When controlling the projector, connect the projector to a computer with an
RS-232C cable. This port is for control use and should not normally be used.
s p.100
h Trigger out port
i Service port
Connects with external devices such as motorized screens. s p.20
j Remote receiver
k Power inlet
Receives signals from the remote control. s p.24
Connects to the RGB output port on a computer. s p.20
Service port. This is not normally used.
Connect the power cord. s p.25
14
Introduction
Base
Name
Function
a Front adjustable foot When setup on a surface such as a table, extend the foot to adjust the horizontal
tilt. s p.28
b Ceiling mount fixing Attaches the optional ceiling mount here when suspending the projector from a
points (four points) ceiling. s p.96
c Cable cover fixing
screw
Attaches the optional cable cover.
d Air exhaust vent
Exhaust vent for air used to cool the WirelessHD receiver. When suspending from
a ceiling, make sure it is setup so that dust does not collect in this section.
e Screw for anamor‐
phic lens
Attaches the anamorphic lens.
15
Introduction
Appearance
Units: mm
a
b
c
Center of lens
Distance from center of lens to suspension bracket fixing point
Lens direction
16
Preparing
Installing
Various Projection Methods
Warning
• A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If
it is not installed correctly, it could fall causing an accident and injury.
• If you use adhesives, lubricants, or oil on the ceiling mount fixing points to prevent screws from loosening,
or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall
from its ceiling mount. This could cause serious injury to anyone under the projector and also damage the
projector.
• Do not setup the projector on its side. This may cause malfunctions to occur.
• Try not to setup the projector in locations subject to high humidity and dust, or in locations subject to smoke
from fires or tobacco smoke.
Attention
Clean the air filter once every three months. Clean it more often if the environment is particularly dusty.
s p.89
Placing on a table and so on and projecting Suspending from the ceiling and projecting
c
When projecting from a ceiling, change Projection to a ceiling setting. s Settings Projection p.70
Using lens shift
With lens shift, you can adjust the projection position up,
down, left, and right.
This allows you to make easy adjustments without distorting
the image, even if you cannot setup the projector directly in
front of the screen.
17
Preparing
Adjusting the Projection Size
The size of the projection increases as the projector is moved away from the screen. Use the table below to
setup the projector at the optimum position from the screen. The values given here are for your reference only.
* Distance from the center of the lens to the edge of the projected image.
(A: When lens shift is raised to its highest level)
(B: When lens shift is lowered to its lowest level)
Unit: cm
16:9 Screen Size
D
WxH
Projection Distance (C)
Minimum
(Wide)
Maximum
(Tele)
Lens Shift Maximum Values*
Distance (A)
Distance (B)
40"
89 x 50
117
252
23
73
60"
130 x 75
177
380
34
109
80"
180 x 100
238
508
46
145
100"
220 x 120
298
636
57
181
120"
270 x 150
359
764
68
218
150"
330 x 190
450
956
85
272
180"
440 x 250
540
1148
103
327
4:3 Screen Size
D
WxH
Projection Distance (C)
Minimum
(Wide)
Maximum
(Tele)
Lens Shift Maximum Values*
Distance (A)
Distance (B)
40"
81 x 61
144
309
28
89
60"
120 x 90
218
466
42
133
80"
160 x 120
292
623
56
178
100"
200 x 150
366
779
70
222
120"
240 x 180
440
936
84
267
150"
300 x 230
551
1171
105
333
200"
410 x 300
736
1562
139
* Vertical and horizontal lens shift cannot both be set to their maximum values. s p.28
18
444
Preparing
Connecting a Device
Attention
• Make cable connections before connecting to a power outlet.
• Check the shape of the cable's connector and the shape of the port, and then connect. If you force a connector
of a different shape into the port, it could cause damage and a malfunction to occur.
EH-TW9200W/EH-TW8200W comes with an interface cover allowing you to clearly see the connector section
on the rear. Remove the interface cover before connecting any cables. s p.21
Connecting Video Equipment
To project images from DVD players or VHS video and so on, connect to the projector using one of the
following methods.
When using an HDMI cable
Fix the HDMI cable in place using the HDMI cable clamp. (EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200
only) s p.22
When using a video cable
When using a component video cable
c
• The cable differs depending on the output signal from the connected video equipment.
• Some types of video equipment are capable of outputting different types of signals. Check the user's
guide supplied with the video equipment to confirm which signals can be output.
• Since this projector has no built-in speaker, connect your AV system to enjoy the audio from connected
equipment.
19
Preparing
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
When using a computer cable
When using an HDMI cable
Fix the HDMI cable in place using the HDMI cable clamp. (EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200
only) s p.22
Connecting External Devices
Connecting to the Trigger out port
To connect external devices such as motorized screens, connect a mini-jack stereo cable (3.5 mm) to the
Trigger Out port.
When set to on, a signal (12 V DC) is output from this port to communicate the projector's status (on or off)
to connected devices such as electric screens.
c Out p.73
When using the Trigger out port, set the Trigger Out function. s Extended - Operation - Trigger
Connecting WirelessHD devices (EH-TW9200W/EH-TW8200W only)
The projector receives transmissions from the WirelessHD Transmitter, and projects the images. s p.52
Change the projected image by pressing the
control panel.
c
button on the remote control or the
button on the
• When receiving WirelessHD images, make sure WirelessHD is set to On. s Settings -
WirelessHD p.70
• You can change which device is displayed by selecting a device from Device Connections in HDMI
Link. s HDMI Link-Device Connections p.62
20
Preparing
Connecting smartphones or tablets (EH-TW9200W/EH-TW8200W only)
You can connect MHL compatible smartphones or tablets to the WirelessHD Transmitter.
Use an MHL compatible cable to connect the micro USB port of smartphones and tablets to the HDMI5 port
on the WirelessHD Transmitter.
You can operate smartphones or tablets from the projector re‐
mote control.
You can also view video and listen to music while charging a
smartphone or tablet.
Attention
• Be sure to use an MHL compatible cable for making connections. During charging, the smartphone or tablet
could generate heat, cause a liquid leak, explode or generate other conditions that could result in a fire.
• When a connection is made using an MHL-HDMI conversion adapter, it may not be possible to charge or
control the device from the remote control.
c
Some devices use more power during video playback than what is supplied and will therefore not
enable charging during video playback or other operations.
Removing the Interface Cover
The interface cover is attached to the connector section on the rear of EH-TW9200W/EH-TW8200W. Remove
this cover when using a cable to connect a device.
There are gaps at the bottom of the interface cover that allows you to pull the cover forward and lift it from
the grooves at the top.
c
• When reattaching, first insert the protruding sections into the grooves at the top.
• Make sure you store the interface cover safely, as you need this when transporting the projector.
21
Preparing
Connecting an HDMI Cable Clamp (EH-TW9200W/EH-TW9200/EH-TW8200W/EHTW8200 only)
If the HDMI cable is thick and hangs down, make sure you secure it to the cable holder with an HDMI clamp
so that the cable's weight does not disconnect it from the port.
22
Preparing
Preparing the Remote Control
Installing the Remote Control Batteries
Attention
• Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the
correct way.
• You cannot use other batteries except for the AA size manganese or alkaline.
a
Remove the battery cover.
b
Replace the old batteries with new
batteries.
c
While pushing the battery compartment
cover catch, lift the cover up.
Reattach the battery cover.
Press the cover until it clicks into place.
c
Check the polarity of the batteries (+) and
(-) before installing.
23
If delays in the responsiveness of the
remote control occur or if it does not
operate, it probably means that the
batteries are becoming flat. When this
happens, replace them with new
batteries. Have two AA size manganese
or alkaline batteries ready.
Preparing
Remote Control Operating Range
The operation range for the WirelessHD Transmitter differs. s p.60
Operating range (left to right)
Operating range (top to bottom)
* Remote control signals are not available in this
range.
24
Basic Operations
Starting and Ending Projection
Turning on the Projector and Projecting
a
Connect the equipment to the
projector.
b
Connect the power cord.
c
Turn on the connected equipment.
d
Turn on the projector.
Remote control
Control panel
Connect using the power cord supplied.
The lens shutter opens, and projection
starts.
c
When Direct Power On is set to
On, you can start projecting by
simply connecting the power cord
to the projector without having to
press any buttons. s Extended Operation - Direct Power
On p.73
Warning
Do not look into the lens during projection.
c
• This projector provides a Child Lock function to prevent children from accidentally turning the power
on and a Control Panel Lock function to prevent accidental operations and so on. s Settings - Lock
Setting - Child Lock/Control Panel Lock p.70
• When using at an altitude of 1500 m or more, set High Altitude Mode to On. s Extended - Operation -
High Altitude Mode p.73
• This projector provides an Auto Setup function to automatically select the optimum settings when the
input signal for the connected computer image changes. s Signal - Auto Setup p.68
• This projector comes with a Trigger out port to communicate the current status of the projector's power
(on/off) to external devices. When using this function, set Trigger Out. s Extended - Operation -
Trigger Out p.73
25
Basic Operations
If the Target Image is not Projected
If the image is not projected, you can change the source using one of the following methods.
Remote control
Press the button for the target port.
c
Control panel
Press the
Press the
button and select the target port.
button to confirm the selection.
• For video equipment, start playback first and then change the source.
• If the color looks unnatural when changing to a Video or Component source, check that the port you
have connected to is the same as the Input Signal. s Extended - Input Signal - Video Signal/
Component p.73
Turning Off
a
b
c
Turn off the connected equipment.
c
When Power Off Link is set to
On in the HDMI Link menu,
turning off HDMI CEC compatible
equipment may also turn off the
projector. s Settings - HDMI
Link - Power Off Link p.70
button again.
Projection ends, and the lens shutter closes
automatically.
Press the
button on the remote
control or the projector's control
panel.
Remote control
Press the
to Off, you can turn off the
c set
projector by pressing the
When Standby Confirmation is
button on the remote control
once. s Extended - Display Standby Confirmation p.73
Control panel
d
Wait until cool-down is complete.
e
Disconnect the power cord.
A confirmation message is displayed.
26
The operation indicator on the projector's
control panel stops flashing.
c
If the power cord is connected,
some electricity is consumed even
if no operations are made.
Basic Operations
Adjusting the Projected Screen
Displaying the Test Pattern
When adjusting the zoom/focus or the projection position just after setting up the projector, you can display
a test pattern instead of connecting video equipment.
Press the
button on the remote control to display the test pattern.
You can adjust the display position and so on by using this test pattern.
For EH-TW9200W/EH-TW9200, you can also select patterns that display R (red), G (green), and B (blue)
individually, as well as the pattern for adjusting the display position. You can use it as a pattern to perform
color adjustment when an image signal is being input.
Press the
button to end the test pattern display.
For EH-TW9200W/EH-TW9200, you can also end by selecting Exit.
Adjusting the Focus
Turn the focus ring to adjust the focus.
27
Basic Operations
Adjusting the Projection Size (Zoom Adjustment)
Turn the zoom ring to adjust the size of the projected screen.
Adjusting the Projector's Tilt
If the projection screen is tilted (the left and right sides of the projector are at different heights) when the
projector is setup on a table, adjust the front foot so that both sides are level with each other.
Adjusting the Position of the Projected Image (Lens Shift)
If the projector cannot be setup in front of the screen, you can adjust the position of the image by using lens
shift.
Make adjustments using the lens shift dial.
You can adjust the position up, down, left, and right
within the range of the dotted line shown in the illus‐
tration on the right.
The vertical (V) position (up and down) can be adjusted
by up to 96% of the height of the screen, while the hor‐
izontal (H) position (right and left) can be adjusted by
up to 47% of the width of the screen.
To reset the image position to the center, return the dial
to the central position.
To locate the center of the lens shift range, turn the lens
shift dial until you hear it click.
28
Basic Operations
Caution
When transporting the projector, return the horizontal lens position to the central position and the vertical
lens position to the bottom position. If you transport the projector when the lens is shifted up, down, left,
or right, the lens shift mechanism could be damaged. Also, attach the protective pad that was attached
when you purchased it.
correct the distortion completely. When using lens shift, setup the projector so that it is parallel
c toto the
screen, and then only use lens shift to adjust the position.
If keystone distortion occurs when projecting at an angle by using lens shift, you may not be able
Correcting Keystone Distortion
You can use the
buttons on the control panel to correct keystone distortion.
Open the control panel cover at the side to operate the control panel. s p.9
Press the
or
buttons to display the adjustment gauges.
When the gauges are displayed, press the
and
buttons to perform vertical correction.
When the top or bottom is too wide
c
• The projected screen becomes smaller when correcting keystone distortion. Increase the projection
distance to fit the projected screen to the screen size.
• You can make keystone settings from the Configuration menu. s Settings - Keystone p.70
• You can make effective corrections within a projection angle of 30° top to bottom.
• For position adjustment, you can maintain the quality of the projected image by performing correction
using lens shift. Use keystone when you cannot make adjustments using lens shift.
Hiding the Image Temporarily
You can use this to temporarily hide the image on the screen.
Press the
button to show or hide the image.
c point at which you hid the image using the
For movies, because the movie continues to play even when it is hidden, you cannot return to the
button.
29
Adjusting the Image
Adjusting the Image
Selecting the Projection Quality (Color Mode)
You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the
image varies depending on the mode selected.
a
Press the
c
b
button.
You can make settings from the Configuration menu. s Image - Color Mode p.66
Select Color Mode.
Press the
buttons from the displayed menu to select Color Mode, and then press the
button to confirm the selection.
When projecting 2D images
You can select Dynamic, Living Room, Natural, THX, and Cinema.
3D Dynamic, 3D Cinema, and 3D THX are grayed out and cannot be selected.
When projecting 3D images
You can select 3D Dynamic, 3D Cinema, and 3D THX.
Dynamic, Living Room, Natural, THX, and Cinema are grayed out and cannot be selected.
Choices when projecting 2D images
Mode
Application
Dynamic
Ideal for use in a bright room.
Living Room
Ideal for use in a bright room. Images are clear and sharp.
Natural
Ideal for use in a dark room. We recommend performing color adjustment in this mode.
s p.6
THX*
A color mode authorized by THX Ltd.
Cinema
Ideal for watching movies and concerts in a dark room.
* THX may not be displayed depending on the model you are using.
30
Adjusting the Image
Choices when projecting 3D images
Mode
Application
3D Dynamic
For use when projecting 3D images. Images are bright and sharper than 3D Cinema.
3D Cinema
For use when projecting 3D images. Produces crisper colors than 3D Dynamic.
3D THX*
For use when projecting 3D images. A color mode authorized by THX Ltd.
* 3D THX may not be displayed depending on the model you are using.
Switching the Screen Between Full and Zoom (Aspect)
You can change the input signal's type, aspect ratio, and resolution to match the Aspect of the projection
screen.
The available Aspect varies depending on the image signal currently being projected.
a
Press the
c
b
button.
Use the
buttons to
select the setting name, and then
button to confirm the
press the
selection.
You can make settings from the
Configuration menu. s Signal Aspect p.68
c
Aspect may not be available
depending on the type of signal.
By normally selecting Auto, the optimum aspect is used to display the input signal. Change the setting if you
want to use a different aspect.
The table below shows the image projected on a 16:9 screen.
Input Image
Setting Name (Aspect)
Normal
Full
Zoom
4:3 Images
16:9 Images
When projecting 16:9 images, Full and Zoom cannot be
selected.
Images Recorded Using
Squeeze
31
Adjusting the Image
Input Image
Setting Name (Aspect)
Normal
Full
Zoom
Letterbox Images*
Matches the vertical size of Uses the entire projection
the projection panel. The panel.
aspect ratio differs de‐
pending on the input im‐
age.
Retains the aspect ratio of
the input signal, and
matches the horizontal
size of the projection pan‐
el. The top and bottom of
the image may be trunca‐
ted.
* The letterbox image used in this explanation is a 4:3 aspect ratio image displayed in 16:9 with black margins at
the top and bottom for subtitle placement. The margins at the top and bottom of the screen image are used for
subtitles.
Notes
For EH-TW9200W/EH-TW9200, you can also set Anamorphic Wide and Horiz. Squeeze.
c
• If Anamorphic Wide is selected when Overscan is set, the image may be truncated. Set Overscan to
Off and then project. s Signal - Advanced - Overscan p.68
• When projecting 3D images in Anamorphic Wide, only 1080p/24 Hz/frame packing signals are
supported.
Set Anamorphic Wide and attach a commercially available anamorphic lens to enjoy DVDs, Blu-rays, and so
on of images recorded at Cinema Scope size.
Horiz. Squeeze stretches the horizontal aspect of the input signal. This allows you to project across the full
width of the screen when using a commercially available anamorphic lens.
c
Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected
image for commercial purposes or for public viewing may infringe upon the rights of the copyright
holder of that image based on copyright law.
32
Adjusting the Image
Absolute Color Adjustments
Adjusting Hue, Saturation, and Brightness
You can adjust the hue, saturation, and brightness for each of the R (red), G (green), B (blue), C (cyan), M
(magenta), and Y (yellow) colors.
Hue
Adjusts the overall color of the image to be blue, green, or red.
Saturation
Adjusts the overall vividness of the image.
Brightness
Adjusts the overall color brightness of the image.
a
Press the
c
b
button.
c
Use the
buttons to
select Hue, Saturation, or
Brightness.
d
Use the
buttons to make
adjustments.
You can make settings from the
Configuration menu. s Image Advanced - RGBCMY p.66
Use the
buttons to
select the color you want to adjust,
and then press the
button to
confirm the selection.
Press the
color.
button to adjust another
button to return the
Press the
adjustments to their default values.
e
33
Press the
menu.
button to exit the
Adjusting the Image
Adjusting the Gamma
You can adjust slight coloration differences that may occur due to the device being used when the image is
displayed.
You can use one of the following three methods selected from the Configuration menu.
Setting Method
Menu Settings
Select and adjust the correction Image - Advanced - Gamma
value
Adjust while viewing the image* Image - Advanced - Gamma - Customized - Adjust it from the image
Adjust using the gamma adjust‐ Image - Advanced - Gamma - Customized - Adjust it from the graph
ment graph*
* EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200 only
Select and adjust the correction value
Select the adjustment value, and then press the
to confirm the selection.
button
The smaller the value, the lighter the dark portions of the
image become, but bright areas may appear discolored. The
upper part of the gamma adjustment graph becomes roun‐
ded.
When a large value is entered, bright parts of the image be‐
come dark. The lower part of the gamma adjustment graph
becomes rounded.
c
• The horizontal axis of the gamma adjustment graph shows the input signal level, and the vertical axis
shows the output signal level.
• Press the
button to return the adjustments to their default values.
Adjust while viewing the image (EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200 only)
Make adjustments while viewing the image being projected.
a
b
Move the gamma icon displayed on
the image being projected to the area
for which you want to adjust the
brightness, and then press the
button.
The gamma adjustment graph is displayed.
34
Use the
buttons to
adjust the brightness, and then press
button to confirm the
the
selection.
Adjusting the Image
Adjust using the gamma adjustment graph (EH-TW9200W/EH-TW9200/EH-TW8200W/EHTW8200 only)
Make adjustments while viewing the gamma adjustment graph for the image being projected.
a
b
Use the
buttons to select the
part you want to adjust from the
graph.
Use the
buttons to
adjust the brightness, and then press
the
button to confirm the
selection.
Adjusting the RGB (Offset/Gain)
For the image's brightness, you can adjust the dark areas (Offset) and the bright areas (Gain) for R (red), G
(green), and B (blue). The image becomes brighter when moved to the right (positive) and darker when moved
to the left (negative).
Offset
When the image is made brighter, shading for the darker sections is more vividly expressed.
When the image is made darker, the image appears more full-bodied but shading for the
darker sections is harder to distinguish.
Gain
When the image is made brighter, the bright sections become whiter and shading is lost.
When the image is made darker, shading for the bright sections is more vividly expressed.
The menu is displayed in the following order.
Image - Advanced - RGB
Use the
use the
buttons to select the item, and then
buttons to make the adjustments.
c Press the
button to return the adjustments to their default values.
Color Temp.
You can adjust the overall tint of the image. Make adjustments if the image is a little too blue or too red and
so on.
The menu is displayed in the following order.
Image - Color Temp.
Use the
buttons to make adjustments.
Blue tints grow stronger as the value is increased, and red
tints grow stronger as the value is reduced.
35
Adjusting the Image
c
• The Color Temp. setting varies with the Color Mode setting.
• Press the
button to return the adjustments to their default values.
Skin Tone
You can adjust the skin tone. Make adjustments if the skin tone is too red or too green and so on.
The menu is displayed in the following order.
Image - Skin Tone
Use the
buttons to make adjustments.
The image becomes greener when set to the right (positive)
and redder when set to the left (negative).
c
Press the
button to return the adjustments to their default values.
36
Adjusting the Image
Detailed Image Adjustments
Adjusting the Sharpness
You can make the image clearer.
This cannot be set in the following situations.
• When a computer signal is being input
• When projecting 3D images
Thin Line Enhancement
Details such as hair and patterns on clothing are enhanced.
Thick Line Enhancement
Rough parts such as outlines for entire subjects or the background are enhanced,
making the overall image clearer.
Vert. Line Enhancement
Enhances the image horizontally or vertically.
Horiz. Line Enhancement
a
Press the
d
button.
Remote control
Control panel
Use the
buttons to
select the item, and then use the
buttons to make the adjustments.
The image is enhanced when moved to the
right (positive) and softer when moved to
the left (negative).
The Configuration menu is displayed.
b
c
Select Image - Sharpness.
The Sharpness adjustment screen is
displayed.
The upper bar adjusts high and low areas
simultaneously.
button to return the
Press the
adjustments to their default values.
Select Advanced at the top right of
the screen, and then press the
button to confirm the selection.
e
The Advanced adjustment screen is
displayed.
Processing is set to Fast in the
c Signal
Signal menu.
This cannot be set when Image
s
Advanced - Image
Processing p.68
37
Press the
menu.
button to exit the
Adjusting the Image
Setting Auto Iris
By automatically setting the luminance according to the brightness of the displayed image, it lets you enjoy
deep and rich images.
You can select the luminance adjustment tracking for changes in brightness in the displayed image from
Normal to High Speed.
(Depending on the image, you may hear the auto iris operating, but this is not a malfunction.)
a
Press the
b
button.
Use the
buttons to
select the item, and then press the
button to confirm the selection.
menu.
c Configuration
Auto Iris p.66
You can make settings from the
s Image -
Frame Interpolation (EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200 only)
This setting compares the current and previous frames, and then creates a frame between them to reduce
fuzziness and produce clearer images.
You can select the level of interpolation from Low, Normal, or High. If you notice any distortion and so on
after changing the setting, set it to Off.
a
Press the
c
b
button.
• You can make settings from the
Configuration menu. s Signal -
Frame Interpolation p.68
• This cannot be set when Image
Processing is set to Fast in the
Signal menu. s Signal Advanced - Image
Processing p.68
• This cannot be set when a
computer image signal is being
input.
• When projecting 3D images, this
setting is enabled only for 1080p/
24 Hz signals.
38
Use the
buttons to
select the item, and then press the
button to confirm the selection.
Adjusting the Image
Super-resolution
This setting sharpens blurred images, enhancing the apparent detail of the image by increasing the resolution
of the image signal.
Depending on the image, distortion at the edge of the image may be enhanced. If you notice any distortion,
set it to "0".
a
Press the
b
button.
Use the
buttons to make
adjustments.
The higher the number, the stronger the
effect.
c
• You can make settings from the
configuration menu. s Signal -
Super-resolution p.68
• This cannot be set when a
computer image signal is being
input.
• This cannot be set when
converting 2D to 3D images.
s Signal - 3D Setup - 2D-to-3D
Conversion p.68
• When projecting 3D images, this
setting is enabled only for 1080p/
24 Hz/frame packing signals.
c
Press the
menu.
c
Set Panel Alignment to On.
button to exit the
Panel Alignment
Adjusts the pixel color shift of the LCD display.
a
Press the
button.
The Configuration menu is displayed.
b
Select Extended - Panel Alignment,
button to
and then press the
confirm the selection.
is enabled. When set to Off,
c value
the corrected value returns to the
When set to On, the adjusted
The Panel Alignment adjustment screen is
displayed.
default value.
d
39
In Select Color, select the color you
want to adjust.
Adjusting the Image
e
In Pattern Color, select the pattern
(color combination) used for
adjustments.
f
Select Start Adjustments, and then
button to confirm the
press the
selection.
h
Adjustments start. Adjustments are
performed in four corners starting from the
top-left corner.
g
After adjusting four corners, select
button to
Exit, and then press the
confirm.
c
Use
buttons to
adjust, and then press the
button
to move to the next adjustment point.
i
If the four corners still need
adjustments, select Select
intersection and adjust, and
then continue adjustments.
Press the
menu.
button to exit the
Image Processing
Improves the response speed for images projected at high-speed, such as games.
This is only available when receiving a progressive signal input from the Component, Video, HDMI1, or
HDMI2 ports, or from WirelessHD.
a
Press the
button.
c
Use the
buttons to
select the item, and then press the
button to confirm the selection.
d
Press the
menu.
The Configuration menu is displayed.
b
Select Signal - Advanced - Image
Processing.
c
button to exit the
• This does not support 3D images.
• If Image Processing is set to Fast, the following settings cannot be changed:
-Noise Reduction, Frame Interpolation, 2D-to-3D Conversion are fixed at Off.
-Sharpness is fixed at Standard.
40
Adjusting the Image
Selecting the Color Gamut (EH-TW9200W/EH-TW9200 Only)
Sets the color gamut to match the standard for the video device being used. You can easily adjust the color
gamut by selecting from the color space names registered in advance.
This can be set when Color Mode is set to Natural.
a
Press the
button.
c
Select the color space according to the
device being used.
d
Press the
menu.
The Configuration menu is displayed.
b
Select Image - Advanced - Color
Gamut.
41
button to exit the
Adjusting the Image
Viewing the Image at the Saved Image Quality
(Memory Function)
Saving Function
You can save the adjustment values for some images and image quality settings in the Configuration menu
for later use (Save Memory).
Because these saved adjustment values can be loaded from the remote control, you can easily switch to your
preferred image quality (Load Memory).
The following Configuration menu functions can be saved.
Image
s p.66
Color Mode, Power Consumption, Brightness, Contrast, Color Saturation, Tint, Sharpness,
Color Temp., Skin Tone, Auto Iris
Advanced
Signal
s p.68
Sharpness, Offset, Gain, Gamma, Hue, Saturation, Brightness, EPSON Super
White
Deinterlacing, Motion Detection
Advanced
Noise Reduction, Setup Level, Overscan, HDMI Video Range
Saving a Memory
a
Make settings that you want to save to
the Configuration menu.
b
Press the
c
Use the
buttons to
select Save Memory, and then press
the
button to confirm the
selection.
d
button.
Use the
buttons to
select the memory name to be saved,
and then press the
button to
confirm the selection.
The current projector settings are saved to
the memory.
When the mark to the left of the memory
name turns green, saving is complete. If you
select a memory name that has already
been used, a message is displayed asking if
you want to overwrite the data. If you select
Yes, the previous content is erased and the
current settings are saved.
The Save Memory screen is displayed.
42
Adjusting the Image
Loading a Memory
a
Press the
b
Select the target memory name.
button, and then select Load Memory.
The Load Memory screen is displayed.
c
• The color mode saved to the memory is displayed on the right.
• Depending on the input signal, part of the loaded memory item may not be applied to the
projected image.
• Memories saved for 2D images can only be loaded when projecting 2D images. Memories saved
for 3D images can only be loaded when projecting 3D images.
Deleting a Saved Memory
a
Press the
b
Select the target memory name.
button, and then select Erase Memory.
The Erase Memory screen is displayed.
A confirmation message is displayed. If you select Yes, the content of the saved memory is erased.
c
If you want to erase all of the saved memories, go to Reset - Reset Memory on the
Configuration menu. s p.75
Renaming a Memory
You can rename each memory name using up to 12 characters. Giving the memory a name that is easy to
remember is useful when loading the memory.
a
Press the
b
Select the target memory name.
c
Select a displayed name or Customized.
button, and then select Rename Memory.
The Rename Memory screen is displayed.
The name list screen is displayed.
To enter a name of your own, select Customized, and then go to step 4. If you select Customized, a
keyboard is displayed.
If you select from the name list, check that the memory name has been changed.
43
Adjusting the Image
d
Enter a name.
Use the
buttons to select a
button to con‐
character, and then press the
firm the selection. Enter up to 12 characters.
When you have finished entering the name, se‐
lect Finish.
The memory name is changed.
44
Useful Functions
Enjoying 3D Images
Setting 3D Images
Set the source to HDMI1, HDMI2, or WirelessHD (EH-TW9200W/EH-TW8200W only) to view 3D images.
The projector supports following 3D formats.
• Frame Packing
• Side by Side
• Top and Bottom
When the projector detects a 3D format
The projector automatically projects a 3D image when detecting a 3D format.
When the projector cannot detect a 3D format
Some 3D TV broadcasts may not contain 3D format signals. If this
happens, set the 3D format manually. Press the
button to
set the 3D format on the AV device.
c
• For details on 3D format settings on the AV device, see the documentation supplied with the AV device.
• When the 3D format has not been correctly set up, an image will not be correctly projected as shown
below.
If the 3D image cannot be viewed
Check the following if the 3D effect is not displayed correctly, even after setting the 3D formats.
• The synchronization timing for the 3D Glasses may have been inversed. Inverse the synchronization using Inverse
3D Glasses, and then try again. s Signal - 3D Setup - Inverse 3D Glasses p.68
• The image is not displayed in 3D if 3D Display is set to Off. Press the
button on the remote control. s Signal -
3D Setup - 3D Display p.68
c
• How a 3D image is perceived varies depending on the individual.
• When a 3D image is displayed, a warning about viewing 3D images is displayed. You can turn off this
warning by setting 3D Viewing Notice to Off. s Signal - 3D Setup - 3D Viewing Notice p.68
• You can also convert 2D images to 3D images. s p.50
• During 3D projection, the following Configuration menu functions cannot be changed.
Aspect (set to Normal*), Noise Reduction (set to Off), Overscan (set to Off), Advanced - Sharpness,
Picture in Picture
• How the 3D image is viewed may change depending on the temperature of the surroundings and how
long the lamp has been used. Refrain from using the projector if the image is not projected normally.
45
Useful Functions
*For EH-TW9200W/EH-TW9200, you can select Anamorphic Wide only when 1080p/24 Hz/frame packing
signals are projected.
Using 3D Glasses
Use the supplied or optional 3D Glasses (ELPGS03) to view 3D images.
Depending on the model, 3D Glasses may not be supplied.
c
The 3D Glasses come with protective stickers. Remove the protective stickers before use.
Charging the 3D Glasses
The following charging methods are available, depending on the model of 3D Glasses being used.
If you have a WirelessHD Transmitter, you can use it to charge the glasses.
If you do not have a WirelessHD Transmitter, you can charge by using an optional USB Charging Adapter.
Charging using the WirelessHD Transmitter
Charging using the USB Charging Adapter
Use the USB cable to connect the 3D Glasses to
the WirelessHD Transmitter.
Use the USB cable to connect the 3D Glasses to
the optional USB Charging Adapter, and then
connect the USB Charging Adapter to an electrical
outlet.
When a cable is connected to the HDMI5 port, the
WirelessHD Transmitter cannot charge 3D
glasses.
Attention
• Only connect to an electrical outlet that uses the voltage displayed on the adapter.
• Note the following points when handling the supplied microUSB cable.
- You should not bend, twist, or pull the cable with too much force.
- You should not modify the cable.
- You should not perform wiring near an electric heater.
- You should not use the cable if it is damaged.
Pairing 3D Glasses
To create 3D images, the 3D Glasses need to be paired with the projector.
Press the [Pairing] button for a while on the 3D Glasses to start pairing. See the User's Guide for the 3D Glasses
for more information.
46
Useful Functions
c
• For 3D Glasses that have not been used, pairing is performed when the 3D Glasses are turned on. You
do not need to perform pairing if 3D images can already be viewed correctly.
• Once pairing has been performed, you can view 3D images the next time the devices are turned on.
• You can perform pairing within a range of three meters from the projector. While pairing is being
performed, make sure you stay within a range of three meters from the projector. Otherwise, pairing
may not be performed correctly.
• If synchronization cannot be performed within 30 seconds, pairing is automatically canceled. When
pairing is cancelled, 3D images cannot be viewed because pairing fails.
Wearing the 3D Glasses
a
b
Turn on the 3D Glasses by sliding the
[Power] switch to On.
The indicator turns on for several seconds,
and then turns off.
Put on the 3D Glasses and enjoy the
show.
c
• When you have finished using the
3D Glasses, turn them off by
sliding the [Power] switch to Off.
• If the 3D Glasses are not used for
at least 30 seconds, they turn off
automatically. To turn the 3D
Glasses back on, slide the
[Power] switch to Off, and then
slide it back to On.
• You need more pairs of optional
3D Glasses if more than one
person will be viewing the 3D
image. s p.96
Range for Viewing 3D Images
This projector allows you to view 3D images within the range shown in the figure below.
You can view 3D images within a range of 10 meters from the projector.
The distance for pairing is three meters.
47
Useful Functions
c
• 3D images may not be displayed correctly if there is any interference from other Bluetooth
communication devices. Do not use these devices at the same time.
• The communication method for 3D Glasses uses the same frequency (2.4 GHz) as wireless LAN
(IEEE802.11b/g) or microwave ovens. Therefore, if these devices are used at the same time, radio wave
interference may occur, the image may be interrupted, or communication may not be possible. If you
do need to use these devices at the same time, make sure there is enough distance between them and
the projector.
• The 3D Glasses for this projector use the active shutter system based on the standards provided by the
Full HD 3D Glasses Initiative .
™
Warnings Regarding Viewing 3D Images
Note the following important points when viewing 3D images.
Warning
Disassembling or remodeling
• Do not disassemble or remodel the 3D Glasses.
This could cause a fire to occur or the images to appear abnormal when viewing, causing you to feel unwell.
Storage locations
• Do not leave the 3D Glasses or the supplied parts within reach of children.
They could be accidentally swallowed. If anything is accidentally swallowed, contact a doctor immediately.
Wireless (Bluetooth) communication
• Electromagnetic interference may cause medical equipment to malfunction. Before using the device, make
sure there is no medical equipment in the vicinity.
• Electromagnetic interference may cause automatically controlled equipment to malfunction which could
cause an accident. Do not use the device near automatically controlled equipment such as automatic doors
or fire alarms.
Heating
• Do not place the 3D Glasses in a fire, on a heat source, or leave them unattended in a location subject to high
temperatures. Because this device has a built-in rechargeable lithium battery, it could cause burns or a fire if
it ignites or explodes.
Charging
• When charging, connect the supplied cable to the USB port designated by Epson. Do not charge using other
devices as it may cause the battery to leak, overheat, or explode.
• Only use the supplied charging cable to charge the 3D Glasses. Otherwise, it could overheat, ignite, or explode.
Caution
3D Glasses
• Do not drop or press too forcefully on the 3D Glasses.
If the glass sections and so on are broken, an injury could occur. Store the glasses in the soft glasses case.
• Be careful of the edges of the frame when wearing the 3D Glasses.
If it pokes your eye and so on, an injury could occur.
• Do not place your finger in any of the moving sections (such as the hinges) of the 3D Glasses.
Otherwise an injury could occur.
48
Useful Functions
Caution
Wearing 3D Glasses
• Make sure you wear the 3D Glasses correctly.
•
•
•
•
•
Do not wear the 3D Glasses upside down.
If the image is not displayed correctly into the right and left eyes, it could cause you to feel unwell.
Do not wear the glasses unless you are viewing a 3D image.
How a 3D image is perceived varies depending on the individual. Stop using the 3D function if you feel strange
or cannot see in 3D.
Continuing to view the 3D images could cause you to feel unwell.
Stop wearing the 3D Glasses immediately if they seem abnormal or a malfunction occurs.
Continuing to wear the 3D Glasses could cause an injury or cause you to feel unwell.
Stop wearing the 3D Glasses if your ears, nose, or temples become red, painful, or itchy.
Continuing to wear the 3D Glasses could cause you to feel unwell.
Stop wearing the 3D Glasses if your skin feels unusual when wearing the glasses.
In some very rare cases the paint or materials used in the 3D Glasses could cause an allergic reaction.
Caution
Viewing Time
• When viewing 3D images, always take periodic breaks during extended viewing.
Long periods of viewing 3D images may cause eye fatigue.
The amount of time and frequency of such breaks varies from person to person. If your eyes still feel tired or
uncomfortable even after taking a break from viewing, stop viewing immediately.
Caution
Watching 3D Images
• If your eyes feel fatigued or uncomfortable when viewing 3D images, stop viewing immediately.
Continuing to view the 3D images could cause you to feel unwell.
• When viewing 3D images be sure to always wear 3D Glasses. Do not attempt to view 3D images without 3D
•
•
•
•
•
Glasses.
Doing so could cause you to feel unwell.
Do not place any breakable or fragile objects around you when using 3D Glasses.
3D images may cause you to move your body involuntarily, resulting in damage to nearby items or personal
injury.
Only wear 3D Glasses when viewing 3D images. Do not move around while wearing 3D Glasses.
Your vision may appear darker than normal, causing you to fall or injure yourself.
Try to stay as level with the viewing screen as possible when viewing 3D images.
Viewing 3D images at an angle reduces the 3D effect and may cause you to feel unwell due to unintended
color changes.
If using 3D Glasses in a room with fluorescent or LED lighting, you may see flashing or flickering throughout
the room. If this should occur, reduce the lighting until the flickering goes away or turn off the lights completely
when viewing 3D images. In some very rare cases, this flickering could trigger seizures or fainting for some
individuals. If you begin to feel uncomfortable or unwell at any time when viewing 3D images, stop
immediately.
Stay at least three times the height of the screen away from the screen when viewing 3D images.
The recommended viewing distance for an 80-inch screen is at least 3 meters, and at least 3.6 meters for a
100-inch screen.
Sitting or standing any closer than the recommended viewing distance may result in eye fatigue.
49
Useful Functions
Caution
Health Risks
• You should not use 3D Glasses if you are sensitive to light, have a heart condition, or are unwell.
Doing so could aggravate your pre-existing conditions.
Caution
Recommended Age of Use
• The minimum recommended age to view 3D images is six years old.
• Children under the age of six are still developing and viewing 3D images may cause complications. Consult
your doctor if you have any concerns.
• Children viewing 3D images through 3D Glasses should always be accompanied by an adult. It is often difficult
to tell when a child is feeling tired or uncomfortable, which could result in them feeling suddenly unwell.
Always check with your child to ensure that they are not experiencing any eye fatigue during viewing.
Converting 2D Images to 3D and Viewing
You can convert 2D images from HDMI1, HDMI2, or WirelessHD (EH-TW9200W/EH-TW8200W only).
a
Press the
button.
d
Select the strength of the 3D effect,
and then press the
button to
confirm the selection.
e
Press the
The Configuration menu is displayed.
b
Select Signal - 3D Setup, and then
button to confirm the
press the
selection.
The 3D Setup screen is displayed.
c
Select 2D-to-3D Conversion, and
then press the
button to confirm
the selection.
50
button.
Useful Functions
c
• When using 2D-to-3D Conversion, set 3D Format to Auto or 2D. s Signal - 3D Setup - 3D
Format p.68
• If Image Processing is set to Fast, you cannot adjust 2D-to-3D Conversion. s Signal-Advanced -
Image Processing p.68
51
Useful Functions
Connecting with WirelessHD (EH-TW9200W/
EH-TW8200W Only)
Installing the WirelessHD Transmitter
You can use the supplied WirelessHD Transmitter to wirelessly receive image data.
Projector
Transmitter
Multi-media players, game consoles,
and so on
You can use the WirelessHD Transmitter in the following ways.
• You do not need to connect a cable to the projector. This is useful if you cannot set it up near the AV device.
• You can connect up to five AV devices at the same time, and switch images using the remote control.
• As well as the projector, you can connect another output device, such as a television, to the Output port, and then
switch the output using the remote control.
• This allows other output devices connected to the Output port to project images from the connected AV device, even
if the projector is off.
WirelessHD Transmitter part names
Front
Rear
Name
a t button
Function
Turns the transmitter on or off.
button for WiHD Transmit‐
This performs the same function as the
ter control on the lower section of the remote control.
52
Useful Functions
Name
Function
b Input button
Changes to the image from each input port.
button for WiHD Transmit‐
This performs the same function as the
ter control on the lower section of the remote control.
c Output button
Switches the output image to the Wireless or Output port.
button for WiHD Transmit‐
This performs the same function as the
ter control on the lower section of the remote control.
d Main power switch
e AC adapter port
Turns the main power for the transmitter on or off.
f Optical Audio-Out port
g HDMI Output port
Connects to audio devices equipped with an optical digital audio input port.
h HDMI Input port
Connects to the AV device you want to playback. You can switch the input
image using the Input button.
Connects the AC adapter.
Connects to other output devices, such as televisions. You can switch the
output using the Output button.
The HDMI5 port of the unit meets the MHL standards. You can play content
from smartphones or tablets connected with an MHL cable.
i 3D Glasses charging port
j Setup button
Connects a USB cable to charge the 3D Glasses.
k t indicator
(orange/green)
Lit when the WirelessHD Transmitter is on. Lit orange when standing by,
and green when operating (receiving or transmitting images).
l WiHD indicator
(orange)
Indicates the communication status for the WirelessHD.
m Link indicator
(orange)
Indicates the connection status with the projector.
c
This is the button on the back of the WirelessHD Transmitter. It is used for
setting the WirelessHD Transmitter. This is not normally used.
• Lit when wirelessly transmitting images to the projector.
• Off when outputting to the Output port.
• On when projecting images from the projector.
• Flashes when searching for a projector.
• Flashes slowly when standing by in power saving status.
• The receiver is located within the intake vent of the projector and therefore cannot receive any signals
directly from the rear. Set up so that the front of the projector is facing the WirelessHD Transmitter.
Also, make sure that the air intake vent on the left-hand side of the projector is not covered.
• Place the WirelessHD Transmitter on a level surface facing towards the projector.
• You can view the signal strength from the WirelessHD settings menu. s Settings - WirelessHD Reception p.70
Setting the WirelessHD Transmitter
a
Set up the WirelessHD Transmitter
connected to the projector so that
they are facing each other. s p.56
53
Useful Functions
b
c
Connect the WirelessHD Transmitter
to an electrical outlet using the
supplied AC adapter.
Using an HDMI cable, connect the AV
device you want to use to the Input
port on the WirelessHD Transmitter.
You can connect up to five multi-media
players.
c
• You can connect another output device, such as a television, to the Output port on the WirelessHD
Transmitter. You can switch between output images using the remote control. s p.58
• The HDMI5 port of the WirelessHD Transmitter supports the MHL input signal. You can play content
from smartphones or tablets connected with an MHL cable.
Projecting Images
a
Start playback on the AV device, and then turn on the projector and the WirelessHD
Transmitter.
The t indicator on the WirelessHD Transmitter turns on.
b
Check the status of the WiHD indicator on the WirelessHD Transmitter.
If the WiHD indicator is on, go to the next step.
If the indicator is off, press the
button on the remote control or the WirelessHD Transmitter.
Make sure you point the remote control at the WirelessHD Transmitter when using the
on the remote control.
Remote control
54
button
WirelessHD Transmit‐
ter
Useful Functions
c
Check the status of the Link indicator on the WirelessHD Transmitter.
If the WirelessHD Transmitter is connected to the projector, the Link indicator flashes and then remains
on.
c
d
If the indicator continues to flash slowly, the WirelessHD Transmitter cannot connect to the
projector and has entered standby status. Make sure the projector has been setup correctly,
such as turning on the power and so on.
If projection does not start, press the
source.
button on the remote control to change the
Make sure you point the remote control at the projector when using the
control.
button on the remote
Projection starts.
e
When connecting two or more AV devices to the WirelessHD Transmitter, press the
button to switch images. s p.59
c
• When receiving WirelessHD images, make sure WirelessHD is set to On from the Configuration menu.
s Settings - WirelessHD p.70
• Make sure you turn off the WirelessHD Transmitter if it is not going to be used for an extended period.
55
Useful Functions
WirelessHD Settings Menu
a
Press the
b
Select Settings - WirelessHD.
c
button.
The Configuration menu is displayed.
Make settings for each of the
displayed functions.
The WirelessHD settings screen is
displayed.
Available functions on the WirelessHD settings menu
Function
Explanation
Device Connections
Displays a list of available WirelessHD devices that can be connected. The device names
and MAC addresses (device numbers) are displayed in the list. The MAC address is
displayed on the label on the base.
WirelessHD
Enables or disables the WirelessHD function.
Reception
Displays the reception.
WiHD Mode
Use Normal for most situations. Full mode uses the maximum video bandwidth at all
times. Dynamic mode extends wireless ranges while optimally adjusting video band‐
width. Set to Dynamic if the image is interrupted due to weak signals and other causes.
Reset
Resets WirelessHD settings to their default settings.
WirelessHD Transmission Range
The following shows the communication transmission range for the WirelessHD. Make sure you set up the
WirelessHD Transmitter so that it faces the projector.
Horizontal direction (when WiHD Mode is set to Nor‐ Horizontal direction (when WiHD Mode is set to Dy‐
mal)
namic)
56
Useful Functions
Vertical direction (placed on a table and so on)
c
Vertical direction (suspended from a ceiling)
• The wireless transmission range varies depending on the placement and material of the surrounding
•
•
•
•
•
furniture and walls. The values given here are for your reference only.
The projector cannot communicate through walls.
Place the WirelessHD Transmitter on a wooden shelf or other location that does not block the signal
from being transmitted from the front of the device. Note that placing the transmitter on a metal shelf
may cause signal instability.
The antennas are built-into the front of the projector and the WirelessHD Transmitter. Make sure the
antennas face each other (face the front) when setting up the devices.
Place the projector and the WirelessHD Transmitter close to each other, and make sure there are no
other projectors operating in the vicinity.
Depending on the reception strength, the image's color information may be automatically discarded
to avoid any interruptions and maintain a constant connection. To avoid any deterioration in image
quality, adjust the position of the WirelessHD Transmitter so that the Reception is as strong as possible.
Useful Functions of the WirelessHD Transmitter
With the WirelessHD Transmitter, you can connect and switch between five multi-media players (input
devices to be played back) and one output device (an output device displaying an image, such as a television).
Image output
Image input
c using the
Make sure you point the remote control at the WirelessHD Transmitter when performing operations
button (switch input) and the
button (switch output) on the remote control.
57
Useful Functions
Switching the target image
You can switch the output image between devices, such as televisions, connected to the Output port on the
WirelessHD Transmitter and the projector.
a
Turn on the projector or the television.
b
Turn on the WirelessHD Transmitter.
c
Point the remote control at the WirelessHD Transmitter, and then press the
The t indicator on the WirelessHD Transmitter turns on.
Remote control
button.
WirelessHD Transmit‐
ter
Depending on the output target, the WiHD indicator on the WirelessHD Transmitter indicates the
following status.
On: The image is being output to the projector.
Off: The image is being output to another output device.
The output target projected last time is projected the next time the projector is turned on.
c
You can switch to the other output device even when the projector is off.
58
Useful Functions
Switching the image source
You can switch the image source for the AV device connected to the WirelessHD Transmitter. When switching,
each input source is displayed on one screen as a preview. This allows you to switch easily between image
sources even when two or more devices are connected using HDMI.
The projector uses Insta Prevue Technology from Silicon Image, Inc.
Switching the source
a
c
Point the remote control at the
WirelessHD Transmitter, and then
press the
button.
The projected image is switched.
Displaying as a sub-screen
a
Remote control
After selecting the target screen,
please wait for a moment.
Point the remote control at the
WirelessHD Transmitter, and then
press the
button.
WirelessHD Trans‐
mitter
Displays the sub-screen for the connected
device.
Displays the sub-screen for the connected
device.
b
b
When switching between the subscreen and the main screen, press and
hold down the
button (for
approximately 3 seconds) until the
screen changes.
c
To close the sub-screen, press the
button again.
The target screen changes each time
you press the
button.
The projected image is switched.
59
Useful Functions
c
• When the sub-screen is displayed, press
button to switch the image
the
for the sub-screen.
• When the sub-screen is displayed, press
the
button to change the
position and size (large or small) of the
sub-screen. Each time the
button is pressed, the display position
moves from bottom right, top right, top
left, and bottom left allowing you to
change the size.
Remote control operating range
The following shows the operating range between the remote control and the WirelessHD Transmitter.
Operating range (left to right)
Operating range (top to bottom)
60
Useful Functions
Using the HDMI Link Function
HDMI Link Function
When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI port, you can
perform linked operations such as linked power on and volume adjustment for the AV system from one
remote control. Also, when projecting images in WirelessHD, you can use the HDMI link function (EHTW9200W/EH-TW8200W only).
c
• As long as the AV device meets the HDMI CEC standards, you can use the HDMI link function even if
the AV system in-between does not meet the HDMI CEC standards.
• Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time.
Connection Example
Projector
Amplifier
Multi-media players and so on
HDMI Link Settings
By pressing the
button on the remote control, and
setting HDMI Link to On, you can operate the following
functions.
Function
Explanation
Power On Link
Powers on the projector when content is played back on the connected device. Or,
powers on the connected device when the projector is turned on.
Power Off Link
Powers off the connected device when the projector is turned off.
• This only works when the connected device's CEC power link function is enabled.
• Note that depending on the status of the connected device (for example, if it is record‐
ing), the device may not power off.
Input Change Link
Changes the input source of the projector to HDMI when content is played back on the
connected device.
Connected Devices
Operations
You can perform operations such as Play, Stop, Fast Forward, Rewind, Next Chapter,
Previous Chapter, and Pause from the remote control for the projector.
c
• To use the HDMI Link function, you must configure the connected device. See the documentation
supplied with the connected device for more information.
• Even when using the WirelessHD Transmitter with Power On Link set to Device -> PJ or
Bidirectional, if WirelessHD is set to On, this projector also turns on when the AV device connected
to the WirelessHD Transmitter is turned on (EH-TW9200W/EH-TW8200W only). s Settings-HDMI
Link-Power On Link p.70
61
Useful Functions
Device Connections
You can check the connected devices that are available for HDMI Link, and select on the device you want to
project the image from. Devices that can be controlled by HDMI link automatically become the selected
device.
a
b
Press the
button, and then select
Device Connections.
Select the device you want to operate
using the HDMI Link function.
The Device Connections list is displayed.
Devices that have a green icon to their left
are linked.
If the device name cannot be determined
this field is left blank.
c
• If the cable does not meet the HDMI standards, operations are not possible.
• Some connected devices or functions of those devices may not operate properly even if they meet the
HDMI CEC standards. See the documentation and so on supplied with the connected device for more
information.
62
Useful Functions
Projecting Two Different Images Using Picture
in Picture
Types of Screen that can be Displayed Simultaneously
Two different image sources can be projected, one in the main
screen (large screen) and the other in the sub screen (small screen).
You can view the sub screen while viewing the main screen.
HDMI1, HDMI2 and WirelessHD are examples of input sources that
can be displayed in Picture in Picture.
Combinations of input sources for Picture in Picture projection
HDMI1
WirelessHD*
HDMI2
-
HDMI1
-
HDMI2
WirelessHD*
-
* EH-TW9200W/EH-TW8200W only
The projector uses Insta Prevue Technology from Silicon Image, Inc.
Projecting on a Picture in Picture
Starting Picture in Picture
Press the
is projecting.
button on the remote control while the projector
The currently input image is displayed on a Picture in Picture.
The image so far projected then becomes the main screen.
(For EH-TW9200/EH-TW8200/EH-TW7200)
HDMI1 or HDMI2 source other than the source shown in the main
screen is displayed in the sub screen.
(For EH-TW9200W/EH-TW8200W)
The image specified in Picture in Picture - Subscreen Source is
displayed in the sub screen.
If the source being input is not supported, nothing is displayed.
Press the
play.
c
button again to end the Picture in Picture dis‐
You cannot use Picture in Picture display to project
3D images.
63
Useful Functions
Changing the Picture in Picture settings
Use the Picture in Picture menu to change the size or position of the sub screen.
a
b
Press the
button during Picture
in Picture projection.
Make settings for each of the
displayed functions.
The Picture in Picture menu is displayed.
c
The Picture in Picture menu is
displayed directly by pressing the
button during Picture in
Picture projection.
Available functions on the Picture in Picture menu
Function
Explanation
Subscreen Size
Selects the sub screen size using Small and Large.
Subscreen Position
Changes the sub screen position using Top Right, Bottom Right, Top Left, and Bot‐
tom Left.
Subscreen Source*
Selects which source is displayed in the sub screen.
Swap Main/Sub
Changes the main and sub screens.
Exit Picture in Picture
Exits the Picture in Picture display.
* Only EH-TW9200W/EH-TW8200W is displayed.
64
Configuration Menu
Configuration Menu Functions
Configuration Menu Operations
On the Configuration menu, you can make adjustments and settings for Signal, Image, Input Signal, and so on.
a
Press the
c
button.
Remote control
Control panel
Use the
buttons to
select the sub menu on the right, and
then press the
button to confirm
the selection.
The Configuration menu is displayed.
b
Use the
buttons to
select the top menu on the left, and
button to confirm
then press the
the selection.
The adjustment screen for the selected
function is displayed.
When you select the top menu on the left,
the sub menu on the right changes.
d
Use the
adjust the settings.
buttons to
Ex.) Adjustment bar
Ex.) Choices
The line at the bottom is a guide for
operations.
Press the
button on an item displaying
icon to change to the selection
this
screen for that item.
Press the
button to return to the
previous level.
e
65
Press the
menu.
button to exit the
Configuration Menu
c
For items adjusted using an adjustment bar, such as the brightness level, you can press the
button while the adjustment screen is displayed to return the adjustment value to its default value.
Configuration Menu Table
If there is no image signal being input, you cannot adjust items related to the image or signal in the
Configuration menu. Note that the items displayed for the image, the signal, and other information vary
depending on the image signal being projected.
Image menu
Function
Color Mode
Menu/Settings
Explanation
Dynamic, Living Room, Natural, THX*1, Cinema,
3D Dynamic, 3D Cinema, 3D THX
Select a color mode based on your sur‐
roundings and the image you are projec‐
ting. s p.30
Brightness
Adjusts the brightness when the image
appears too dark.
Contrast
Adjusts the contrast between light and
shade in the images. By increasing the
contrast, the images become vivid.
Color Satura‐
tion*2
Adjusts the color saturation for the im‐
ages.
Tint*2
Adjusts the tint for the images.
Sharpness
Standard
Adjusts the image sharpness.
Adjusts the overall image.
Advanced*2
Color Temp.
Thin Line Enhance‐
ment, Thick Line En‐
hancement, Vert. Line
Enhancement, Horiz.
Line Enhancement
Adjusts the image sharpness.
Use this to adjust specific areas. s p.37
-3 - 6 (10 increments)*3
Adjusts the tint for the images. The image
is tinted blue for high values, and tinted
red for low values.
Adjusts the skin tone. The image becomes
greener when set to a positive value and
redder when set to a negative value.
Skin Tone
66
Configuration Menu
Function
Advanced
Menu/Settings
Gamma
Explanation
2, 1, 0, -1, -2
Customized*4 Adjust it from the im‐
age, Adjust it from the
graph
Performs gamma adjustments. You can
select a raw value or adjust the gamma
while looking at the image or graph.
s p.34
Reset
RGB
Adjusts the offset and gain for each R, G,
and B color. s p.35
Offset R/G/B
Gain R/G/B
RGBCMY
R/G/B/C/M/Y
EPSON Super White*5
Color Gam‐
ut*6
Hue, Satura‐
tion, Bright‐
ness
Adjusts the hue, saturation, and bright‐
ness for each R, G, B, C, M, and Y color.
s p.33
On, Off
(This can only be set when the Color
Mode is set to Natural, THX, Cinema, 3D
Cinema, or 3D THXand when receiving
signal input from the HDMI1 or HDMI2
ports, or from WirelessHD.)
Set this to On if you are experiencing
bright over exposure of whites in your im‐
age. When set to On, HDMI Video Range
settings are disabled.
HDTV, EBU, SMPTE-C
Sets the color gamut to match the stand‐
ard for the video device being used.
s p.41
Power Con‐
sumption
Normal, ECO*7
You can set the lamp brightness to one of
two settings.
Select ECO if the images being projected
are too bright. When ECO is selected, pow‐
er consumption during projection decrea‐
ses, and fan rotation noise is reduced.
Auto Iris
Off, Normal, High Speed
You can change the luminance adjust‐
ment tracking for changes in brightness in
the displayed image. Set to Off for no lu‐
minance adjustment. s p.38
Reset
Yes, No
You can reset all adjustment values for
Image to their default settings.
*1 This may not be displayed depending on the model you are using.
*2 This is not displayed when a computer image signal is being input.
*3 When Color Mode is set to Natural, THX, or 3D THX, the settings change to 5000K - 10000K.
*4 Only EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200 is displayed.
*5 Settings are saved for each type of input source or Color Mode.
*6 Only EH-TW9200W/EH-TW9200 is displayed.
*7 When Color Mode is set to THX, the settings change to Extra Bright and Normal.
67
Configuration Menu
Signal menu
Function
3D Setup*1
Menu/Settings
Explanation
3D Display
On, Off
Enables or disables the 3D Display function.
s p.45
2D-to-3D Conver‐
sion
Off, Weak, Medium, Sets the strength of the 3D effect when convert‐
Strong
ing 2D to 3D images. s p.50
3D Format
Auto, Side by Side, Sets the 3D format for the input signal. When set
Top and Bottom, 2D to Auto, the format is recognized automatically.
3D Depth
-10 - 10
Sets the depth for the 3D image.
Diagonal Screen
Size
60 - 300
Sets the projection size for the 3D image. By
matching this to the actual size, you can achieve
the optimum 3D effect.
3D Brightness
Low, Medium, High Sets the brightness for the 3D image.
Inverse 3D Glasses
Yes, No
Reverses the synchronization timing for the left/
right shutters on the 3D Glasses and the left/right
images. Enable this function if the 3D effect is not
displayed correctly.
3D Viewing Notice
On, Off
Turns the notice that appears when viewing 3D
content on or off.
Aspect*2
Auto, Normal, Full, Zoom, Anamorphic
Wide*8, Horiz. Squeeze*8
Selects the aspect mode. s p.31
Tracking*2 *3
Varies depending on the input signal.
Adjusts computer images when vertical stripes
appear in the images.
Sync.*2 *3
0 - 31
Adjusts computer images when flickering, fuzzi‐
ness, or interference appear in the images.
• Adjusting the Brightness, Contrast, or Sharp‐
ness may cause flickering or blurriness.
• Adjusting the synchronization after adjusting
tracking allows for more accurate adjustments.
Position*2 *4
Deinterlac‐
ing*2
Adjusts the display position up, down, left, and
right when a part of the image is missing so that
the whole image is projected.
Off, Video, Film/Auto*5
(This can only be set when receiving signal input
from the Video port or when receiving 480i, 576i,
or 1080i signal input from the Component,
HDMI1, or HDMI2 ports or from WirelessHD.)
Converts the signal from interlaced (i) to pro‐
gressive (p) using a method appropriate for the
image signal.
• Off: This is ideal for dynamic motion images.
• Video: This is ideal for viewing general video
images.
• Film/Auto: Performs the optimal conversion for
film, CG, or animation input signals.
Motion Detec‐
tion*2 *5
1-5
Sets the image motion speed from 1 (slow, for
still images) to 5 (fast, for movies). Change this
setting if you are experiencing poor still image
quality or flickering movies.
68
Configuration Menu
Function
Menu/Settings
Explanation
Frame Interpo‐ Off, Low, Normal, High
lation*5 *6
Reduces afterimages when projecting moving
images by interpolating between one frame and
the next. s p.38
Super-resolu‐
tion*5
0-5
Reduces blurring that occurs at the edge of im‐
ages when the resolution is increased. s p.39
Auto Setup*3
On, Off
Sets whether or not to automatically adjust the
image whenever the input signal is changed.
When enabled, the tracking, display position,
and synchronization are automatically config‐
ured.
Advanced
Noise Reduc‐
tion*2 *5
Off, 1, 2, 3
(This can only be set when Image Processing is
set to Fine.)
Smoothes out rough images. There are three
modes available. Select your favorite setting.
It is recommended that this is set to Off when
viewing image sources in which noise is very low,
such as for DVDs.
Setup Level*2 *5
0%, 7.5%
(This can be set when receiving an NTSC or com‐
ponent video signal from the Video port.)
Change this setting when using devices with a
different black level (Setup Level) such as prod‐
ucts designed for the Korean market. Check the
specifications for your connected device before
changing this setting.
Overscan*2 *7
Auto, Off, 2%, 4%,
6%, 8%
Changes the output image ratio (the range of the
projected image).
(Advanced)
• Off, 2 to 8%: Sets the range of the image. Off
projects all ranges. Depending on the image sig‐
nal you may notice noise at the top and bottom
of the image.
• Auto: This can only be set when receiving signal
input from the HDMI1 or HDMI2 ports, or from
WirelessHD. This may be automatically set to
Off or 8% depending on the input signal.
HDMI Video
Range*1 *2
Auto, Normal, Ex‐
panded
Image Processing*5 Fine, Fast
(This can only be set when EPSON Super
White is set to Off.)
When set to Auto, the video level for the DVD
input signal to the HDMI1 or HDMI2 ports, or to
the WirelessHD is automatically detected and
set.
If you experience under or overexposure when
set to Auto, set the video level of the projector
to match that of the DVD player's video level.
Your DVD player may be set to Normal or Expand.
The Auto option is not displayed when connec‐
ted to a connected device's DVI port.
Performs processing to improve the image.
s p.40
69
Configuration Menu
Function
Reset
Menu/Settings
Explanation
Yes, No
Resets all Signal settings except for Diagonal
Screen Size, 3D Viewing Notice, Aspect, and
Image Processing settings to their default set‐
tings.
*1 This is only displayed when a HDMI1, HDMI2, or WirelessHD image signal is being input. (WirelessHD is for EHTW9200W/EH-TW8200W only.)
*2 Settings are saved for each type of input source or signal.
*3 This is only displayed when a PC image signal is being input.
*4 This cannot be set when an HDMI1, HDMI2, or WirelessHD image signal is being input.
*5 This is not displayed when a PC image signal is being input.
*6 Only EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200 is displayed.
*7 This is only displayed when a Component, HDMI1, HDMI2, or WirelessHD image signal is being input.
(WirelessHD is for EH-TW9200W/EH-TW8200W only.)
*8 Only EH-TW9200W/EH-TW9200 is displayed.
Settings menu
Function
Menu/Settings
Explanation
Keystone
-60 - 60
Performs vertical keystone correc‐
tion. s p.29
HDMI Link
Device Connections
-
Displays a list of devices connected
from the HDMI1 or HDMI2 ports, or
from WirelessHD*.
HDMI Link
On, Off
Enables or disables the HDMI Link
function.
Power On Link
Off, Bidirectional, Device -> PJ, Sets the link function when the
PJ -> Device
power is turned on.
Set to power on the projector when
content is played on a connected
device (Bidirectional or Device ->
PJ) or to power on a connected de‐
vice when the projector is turned on
(Bidirectional or PJ -> Device).
Power Off Link
On, Off
Sets whether or not to power off
connected devices when the pro‐
jector is turned off.
70
Configuration Menu
Function
WirelessHD*
Menu/Settings
Device Connections
-
Displays a list of available Wire‐
lessHD devices that can be connec‐
ted.
WirelessHD
On, Off
Enables or disables the WirelessHD
function.
Reception
Lock Setting
Explanation
Displays the reception.
WiHD Mode
Full, Dynamic
Sets the connection mode of Wire‐
lessHD devices.
Reset
Yes, No
Resets WirelessHD settings to their
default settings.
Note that even if you reset the pro‐
jector, the WirelessHD Transmitter
settings are not reset. See the doc‐
umentation supplied with your
WirelessHD Transmitter for details
on how to reset the WirelessHD
Transmitter.
Child Lock
On, Off
This locks the
button on the
projector's control panel to prevent
children from turning on the pro‐
jector by accident. You can turn on
the power when locked by holding
button for approxi‐
down the
mately three seconds. You can still
turn off the device using the
button, or perform operations with
the remote control as usual.
If changed, this setting is enabled
after you power off the projector
and the cool-down process is com‐
plete.
Note that even if Child Lock is set to
On, the projector still turns on when
the power cord is connected if Di‐
rect Power On is set to On.
Control Panel Lock
On, Off
When set to On, all buttons on the
control panel except for the
button are disabled.
is dis‐
played on the screen if any buttons
are pressed. To unlock, press and
hold the
button on the con‐
trol panel for at least 7 seconds.
If changed, this setting is enabled
once you close the Configuration
menu.
71
Configuration Menu
Function
Projection
Menu/Settings
Front, Front/Ceiling, Rear, Rear/Ceiling
Explanation
Change this setting depending on
how the projector is installed.
• Front: Select if you are projecting
in front of the screen.
• Front/Ceiling: Select if you are
projecting in front of the screen
suspended from the ceiling.
• Rear: Select if you are projecting to
a rear screen from the back.
• Rear/Ceiling: Select if you are pro‐
jecting to a rear screen from the
back when the projector is suspen‐
ded from the ceiling.
User Button
2D-to-3D Conversion, 3D Depth, 3D Brightness, Inverse Select a Configuration menu item to
3D Glasses, Power Consumption, About
button on the
assign to the
remote control. By pressing the
button, the assigned menu
item selection/adjustment screen is
displayed, allowing you to make
one-touch settings/adjustments.
Picture in Pic‐
ture
-
Starts the Picture in Picture display.
s p.63
Reset
Yes, No
Resets all Settings settings except
for Power On Link, Power Off
Link, Projection, and User Button
settings to their default settings.
* Only EH-TW9200W/EH-TW8200W is displayed.
72
Configuration Menu
Extended menu
Function
Operation
Menu/Settings
Explanation
Direct Power On
On, Off
You can set up the projector so that projection
starts as soon as the power cord is plugged in
without any button operations.
Note that when this is set to On, projection starts
if power is restored after a blackout or other
power outage and the power cord is still plugged
into the projector.
Sleep Mode
Off, 5min., 10min.,
30min.
If the set time is exceeded and no signal is input,
the projector is automatically turned off and en‐
ters standby mode. When set to Off, the projec‐
tor never enters sleep mode. When in standby
button on the remote con‐
mode, press the
button on the control panel to
trol or the
start projection.
Illumination
On, Off
Set this to Off if the light from the indicators on
the control panel bothers you when watching a
movie in a dark room.
Trigger Out
On, Off*1
Set the Trigger Out function to communicate the
projector's power on status and so on to external
devices.
When set to Off, no voltage is output from the
Trigger out port.
When set to On or Power, voltage is output from
the Trigger out port when the projector is on.
For Anamorphic Wide, when the projector is on
and Aspect is set to Anamorphic Wide or Horiz.
Squeeze, voltage is output from the Trigger
out port.
If you change this setting, the new setting will
take effect the next time you turn the projector
on.
Off, Power, Ana‐
morphic Wide*2
High Altitude Mode On, Off
Set this to On if you are using the projector above
an altitude of 1500 meters.
73
Configuration Menu
Function
Display
Menu/Settings
Explanation
Menu Position*3
-
Sets the position where the menu should be dis‐
played.
Menu Color
Color 1, Color 2
Selects the color for the top menu.
• Color 1: Black
• Color 2: Blue
Messages
On, Off
Sets whether or not to display the following mes‐
sages (On or Off).
• Item names for image signals, color modes, as‐
pect ratios, and loading memory.
• If the internal temperature is rising when no im‐
age signal is being input or an unsupported sig‐
nal is detected.
Input Signal
Panel Align‐
ment
Display Background Black, Blue, Logo
Selects the screen status when no image signal
is being input.
Startup Screen
On, Off
Sets whether or not to show a startup screen
when projection begins (On or Off). If changed,
this setting is enabled after you power off the
projector and the cool-down process is com‐
plete.
Standby Confirma‐
tion
On, Off
Sets whether or not to display a standby confir‐
mation message (On or Off). s p.26
Video Signal
Auto, NTSC,
NTSC4.43, PAL, MPAL, N-PAL, PAL60,
SECAM
Sets the signal type depending on the video de‐
vice connected to the Video port. When set to
Auto, the video signal is set automatically.
If you notice noise in the image even when set to
Auto, or if you are not seeing any image at all,
select the correct signal type from the available
options.
Component
Auto, YCbCr, YPbPr
Sets the output signal for the video device con‐
nected to the Component port.
When set to Auto, the output signal is set auto‐
matically. If you notice unnatural colors when set
to Auto, set the appropriate output signal from
the available options.
Panel Alignment
On, Off
Enables or disables Panel Alignment.
Select Color
R, B
Select the color to correct.
Pattern Color
R/G/B, R/G, G/B
Select the pattern used for correction.
Start Adjustments
-
Starts Panel Alignment. s p.39
Reset
Yes, No
Resets the correction value.
Language
-
Selects the display language.
Reset
Yes, No
Resets all Extended settings except for High Al‐
titude Mode, Component, and Language set‐
tings to their default settings.
*1 Only EH-TW8200W/EH-TW8200/EH-TW7200 is displayed.
*2 Only EH-TW9200W/EH-TW9200 is displayed.
*3 Only EH-TW9200W/EH-TW9200/EH-TW8200W/EH-TW8200 is displayed.
74
Configuration Menu
Memory menu
Function
Explanation
Load Memory
Loads settings saved using the Save Memory function. s p.43
This cannot be selected if you have not saved any settings with the Save Mem‐
ory function.
Save Memory
Saves certain Image and Signal settings to memory. s p.42
Erase Memory
Erases settings saved to memory that you no longer need. s p.43
Rename Memory
Renames a saved memory. s p.43
Info menu
Function
Explanation
Lamp Hours
Displays the cumulative lamp operating time*.
Source
Displays the source name for the connected equipment currently being projec‐
ted.
Input Signal
Displays the content of Input Signal set in the Signal menu according to the
source.
Resolution
Displays the resolution.
Scan Mode
Displays the scan mode.
Refresh Rate
Displays the refresh rate.
3D Format
Displays the 3D format of the signal input during 3D projection (Frame Packing,
Side by Side, or Top and Bottom).
Sync Info
Displays the image signal information.
This information may be needed if service is required.
Deep Color
Displays deep color.
Video Signal
Displays the settings for Video Signal in the Extended menu.
Status
This is information about errors that have occurred on the projector.
This information may be needed if service is required.
Serial Number
Displays the projector's serial number.
Version
Displays the firmware version of the projector.
* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H",
"11H", and so on.
Reset menu
Function
Explanation
Reset All
Resets all items in the Configuration menu to their default settings.
The following items are not reset to their defaults: Input Signal - Component,
Panel Alignment, Lamp Hours, Language, Save Memory.
Reset Memory
Erases all settings saved using the Save Memory function.
Reset Lamp Hours
Resets the cumulative lamp hours use time to 0 H. Reset when you replace the
lamp.
75
Configuration Menu
Picture in Picture menu
Displayed by pressing the
button during Picture in Picture projection.
Function
Picture in Pic‐
ture
Menu/Settings
Explanation
Subscreen Size
Small, Large
Changes the size of the sub screen.
s p.64
Subscreen Position
Top Right/Bottom Right/Top
Left/Bottom Left
Changes the position of the sub
screen.
Subscreen Source*
HDMI1, HDMI2, WirelessHD
Selects which source is displayed as
the sub screen. s p.64
Swap Main/Sub
Changes the main and sub screens.
s p.64
Exit Picture in Picture
Exits the Picture in Picture display.
s p.64
* Only EH-TW9200W/EH-TW8200W is displayed.
76
Troubleshooting
Problem Solving
Reading the Indicators
You can check the status of the projector from the flashing and lit
the control panel.
, t(operation indicators), o and m on
Refer to the following table to check the projector's status and how to remedy problems shown by the
indicators.
Indicator status during an error/warning
: Lit
Indicators
Status
: Flashing
: Status maintained
: Off
Remedy
Replace Lamp
It is time to replace your lamp. Replace the lamp with a new
lamp as soon as possible. s p.93
The lamp may explode if you continue to use it in this status.
High Temp Warning
You can continue projecting. If the temperature rises too high
again, projection stops automatically.
(blue)/(orange)
• If the projector is installed next to a wall, make sure there is at
(blue)/(orange)
least 20 cm between the wall and the projector's exhaust vent.
• If the air filter is clogged, clean it. s p.89
77
Troubleshooting
Indicators
Status
Internal Error
Remedy
The projector has malfunctioned.
Remove the power plug from the electrical outlet, and contact
your local dealer or the nearest Epson repair center. s Epson
Projector Contact List
(blue)/(orange)
Fan Error
Sensor Error
(blue)/(orange)
Cinema Filter Error
Auto Iris Error
(blue)/(orange)
Power Err. (Ballast)
(blue)/(orange)
Lamp Error
There is a problem with the lamp, or it failed to turn on.
Lamp Failure
• Disconnect the power cord, and then check if the lamp is
Lamp Cover Open
(blue)/(orange)
High Temp Error
(Overheating)
(blue)/(orange)
cracked. s p.93
If it is not cracked, reinstall the lamp and turn on the power.
If reinstalling the lamp does not fix the problem, or if the lamp
is cracked, remove the power plug from the electrical outlet,
and contact your local dealer or the nearest Epson repair center.
s Epson Projector Contact List
• Check that the lamp cover has been properly closed.
• If the air filter is clogged, clean it. s p.89
• When using at an altitude of 1500 m or more, set High Altitude
Mode to On. s Extended - Operation - High Altitude
Mode p.73
The internal temperature is too high.
• The lamp turns off automatically and projection stops. Wait for
about five minutes. When the fan has stopped, disconnect the
power cord.
• If the projector is installed next to a wall, make sure there is at
least 20 cm between the wall and the projector's exhaust vent.
• If the air filter is clogged, clean it. s p.89
• If turning the power back on does not clear the problem, stop
using the projector and remove the power plug from the elec‐
trical outlet. Contact your local dealer or the nearest Epson re‐
pair center. s Epson Projector Contact List
78
Troubleshooting
Indicator status during normal operation
: Lit
Indicators
Status
Standby condition
: Flashing
: Off
Remedy
When you press the
button on the remote control, or the
button on the control panel, projection starts after a short
wait.
Warm-up in progress Warm-up time is about 30 seconds.
The power-off operation is disabled while the projector is warm‐
ing-up.
(blue)
Cool-down in pro‐
gress
All operations are disabled while the projector is cooling-down.
The projector enters standby condition when cool-down is com‐
plete. If for any reason the power cord is disconnected during
cool-down, wait until the lamp has cooled down sufficiently
(about 10 minutes), reconnect the power cord, and then press
the
button on the remote control, or the
button on the
control panel.
Projection in pro‐
gress
The projector is operating normally.
(blue)
c
• Under normal operating conditions, the o and m indicators are off.
• When the Illumination function is set to Off, all indicators are off under normal projection conditions.
s Extended - Operation - Illumination p.73
79
Troubleshooting
When the Indicators Provide No Help
Check the problem
Check the following table to see if your problem is mentioned, and go to the appropriate page for information
on handling the problem.
Problem
Problems relating to im‐
ages
Page
No images appear.
p.80
Projection does not start, the projection area is completely black, or
the projection area is completely blue.
Moving images being projected from a computer are not projected.
p.81
"Not supported" is displayed.
p.82
"No Signal" is displayed.
p.82
Images are fuzzy or out of focus.
p.82
Interference or distortion appears in the images.
p.83
The image is truncated (large) or small, or only a part of the image is
projected.
p.83
Image colors are not right.
p.84
The whole image appears purplish or greenish, images are black &
white, or colors appear dull.*
Images appear dark.
p.84
Projection stops automatically.
p.84
Problems when projection The projector does not turn on.
starts
p.85
Problems with the remote The remote control does not respond.
control
p.85
Problems with the control
panel
Cannot make settings on the control panel
p.85
Problems with 3D
Cannot project correctly in 3D.
p.86
The 3D image is enlarged and truncated
p.86
HDMI Link does not function.
p.86
The device name is not displayed under device connections.
p.87
Problems with HDMI
Problems with WirelessHD Cannot project WirelessHD images.
p.87
Interference, distortion, or interruption appear in WirelessHD
p.88
* Because color reproduction differs between monitors and computer LCD screens, the image projected by the
projector and the color tones displayed on the monitor may not match, however this is not a fault.
Problems relating to images
No images appear
Check
Is the projector turned on?
Remedy
Press the
button on the remote control or the
on the control panel.
80
button
Troubleshooting
Check
Remedy
Is the power cord connected?
Connect the power cord.
Are the indicators switched off?
Disconnect and then reconnect the projector's power cord.
Check that pressing the power button after connection supplies
the projector with power.
Is an image signal being input?
Check that the connected device is turned on. When Messag‐
es is set to On from the Configuration menu, image signal mes‐
sages are displayed. s Extended - Display - Messages p.73
Has the power to the AV amplifier been dis‐
connected?
If an AV amplifier is connected, check the AV amplifier's power
supply.
Is an image signal being sent from the device? Check that an image signal is being sent from the connected
device.
Is the image signal format setting correct?
When Video is input
If nothing is projected even when Video Signal is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Video Sig‐
nal p.73
When Component is input
If nothing is projected even when Component is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Compo‐
nent p.73
Are the Configuration menu settings correct? Reset all of the settings. s Reset - Reset All p.75
(Only when projecting computer image sig‐
nals)
If the connection is made while the power is already turned on,
the key (Function key and so on) that changes the computer's
image signal to external output may not work. Turn off the con‐
Was the connection made while the power of
nected computer, and then turn it back on.
the projector or the computer was already
turned on?
Moving images are not displayed
Check
Remedy
(Only when projecting computer image sig‐
nals)
Depending on the computer's specifications, moving images
may not be displayed when the computer is set to external out‐
put and to the LCD monitor output at the same time.
Is the computer's image signal set to external
Change it so that the image signal is set to external output only.
output and to output to the LCD monitor at
For the computer's specifications, see the documentation sup‐
the same time?
plied with the computer.
81
Troubleshooting
"Not supported" is displayed.
Check
Is the image signal format setting correct?
Remedy
When Video is input
If nothing is projected even when Video Signal is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Video Sig‐
nal p.73
When Component is input
If nothing is projected even when Component is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Compo‐
nent p.73
(Only when projecting computer image sig‐
nals)
Do the image signal's frequency and resolu‐
tion correspond to the mode?
Check the image signal being input in Resolution from the Con‐
figuration menu, and check that it corresponds to the projector's
resolution. s p.97
"No Signal" is displayed.
Check
Remedy
Are the cables connected correctly?
Check that all the cables required for projection are securely
connected. s p.19
Is the correct image input port selected?
Change the image with the source buttons on the remote con‐
trol, or the
button on the control panel. s p.26
Is the connected device turned on?
Turn on the device.
(Only when projecting computer image sig‐
nals)
Change it so that the image signal is set to external output, and
not just the computer's LCD monitor. For some models, when
the image signals are output externally, they no longer appear
on the LCD monitor.
For the computer's specifications, see the documentation sup‐
plied with the computer.
Are the image signals being output to the
projector?
If the connection is made while the power of the projector or the
computer is already turned on, the Fn key (Function key) that
changes the computer's image signal to external output may not
work. Turn off the computer and the projector, and then turn
them back on.
Images are fuzzy or out of focus
Check
Remedy
Has the focus been adjusted?
Adjust the focus. s p.27
Is the projector at the correct distance?
Check the recommended projection range. s p.18
82
Troubleshooting
Check
Has condensation formed on the lens?
Remedy
If the projector is suddenly taken from a cold environment to a
warm environment, or if sudden ambient temperature changes
occur, condensation may form on the surface of the lens, and this
may cause the images to appear fuzzy. Set the projector up in
the room about one hour before it is used. If the projector is wet
from condensation, turn off the projector, disconnect the power
cord, and leave it for a while.
Interference or distortion appear in images
Check
Is the image signal format setting correct?
Remedy
When Video is input
If nothing is projected even when Video Signal is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Video Sig‐
nal p.73
When Component is input
If nothing is projected even when Component is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Compo‐
nent p.73
Are the cables connected correctly?
Check that all the cables required for projection are securely
connected. s p.19
Is an extension cable being used?
If an extension cable is used, electrical interference may affect
the signals.
(Only when projecting computer image sig‐
nals)
The projector uses automatic adjustment functions to project at
the optimum status. However, depending on the signal, some
may not be adjusted correctly even after performing self correc‐
Are the Sync. and Tracking settings adjusted
tions. If this happens, adjust the Tracking and Sync. settings
correctly?
from the Configuration menu. s Signal - Tracking/Sync. p.68
(Only when projecting computer image sig‐
nals)
Set the computer so that the signals being output are compatible
with the projector. s p.97
Is the correct resolution selected?
Part of the image is truncated (large) or small
Check
Remedy
Is the correct Aspect selected?
Press the
button, and then select the Aspect that match‐
es the input signal. s Signal - Aspect p.68
(Only when projecting computer image sig‐
nals)
Set the computer so that the signals being output are compatible
with the projector. s p.97
Is the correct resolution selected?
83
Troubleshooting
Image colors are not right
Check
Is the image signal format setting correct?
Remedy
When Video is input
If nothing is projected even when Video Signal is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Video Sig‐
nal p.73
When Component is input
If nothing is projected even when Component is set to Auto
from the Configuration menu, set the signal that matches the
connected device. s Extended - Input Signal - Compo‐
nent p.73
Are the cables connected correctly?
Is the contrast adjusted correctly?
Check that all the cables required for projection are securely
connected. s p.19
For the Video and Component ports, make sure the connector is
the same color as the cable port. s p.19
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.66
Is the color adjusted correctly?
Adjust the Advanced setting from the Configuration menu.
s Image - Advanced p.66
(Only when projecting images from a video
device)
Adjust the Color Saturation and Tint settings from the Config‐
uration menu. s p.66
Are the color saturation and tint adjusted cor‐
rectly?
Images appear dark
Check
Is the image brightness set correctly?
Is the contrast adjusted correctly?
Remedy
Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.66
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.66
Is it time to replace the lamp?
When the lamp is nearly ready for replacement, the images be‐
come darker and the color quality becomes poorer. When this
happens, replace the lamp with a new lamp. s p.93
Projection stops automatically
Check
Is Sleep Mode enabled?
Remedy
If the set time is exceeded and no signal is input, the lamp turns
off automatically, and the projector enters standby status. The
projector returns from standby status when you press the
button on the remote control or the
button on the control
panel. If you do not want to use Sleep Mode, change the setting
to Off. s Extended - Operation - Sleep Mode p.73
84
Troubleshooting
Problems when projection starts
The projector does not turn on
Check
Remedy
Is the power turned on?
button on the remote control or the
Press the
on the control panel.
Is Child Lock set to On?
When Child Lock is set to On from the Configuration menu, hold
button on the control panel for approximately
down the
three seconds, or perform operations from the remote control.
s Settings - Lock Setting - Child Lock p.70
Do the indicators turn on and off when the
power cord is touched?
Turn off the projector, and then disconnect and reconnect the
projector's power cord. If the problem continues, stop using the
projector, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest projector information
center. s Epson Projector Contact List
button
Problems with the remote control
The remote control does not respond
Check
Remedy
Is the remote control light-emitting area
Point the remote control towards the remote receiver. Also,
pointing towards the remote receiver on the check the operating range. s p.24
projector during operation?
Is the remote control too far from the projec‐ Check the operating range. s p.24
tor?
Is direct sunlight or strong light from fluores‐ Set the projector up in a location where strong light does not
cent lamps shining onto the remote receiver? shine onto the remote receiver.
Are the batteries dead or have the batteries
been inserted correctly?
Make sure the batteries are inserted correctly or replace the bat‐
teries with new ones if necessary. s p.23
Is the remote control pointed at the Wire‐
Make sure you point the remote control at the WirelessHD Trans‐
lessHD Transmitter when operating the WiHD mitter when using the WiHD Transmitter control button on the
Transmitter control button?
remote control. s p.57
(EH-TW9200W/EH-TW8200W only)
Problems with the control panel
Cannot make settings on the control panel
Check
Is Control Panel Lock set to On?
Remedy
If Control Panel Lock is set to On from the Configuration menu,
all of the control panel buttons except for
button are disa‐
bled. Perform operations from the remote control. s Settings
- Lock Setting - Control Panel Lock p.70
85
Troubleshooting
Problems with 3D
Cannot project correctly in 3D
Check
Remedy
Are the 3D Glasses turned on?
Turn on the 3D Glasses.
Is a 3D image being projected?
If the projector is projecting a 2D image, or if an error occurs on
the projector that prevents the 3D image from being projected,
you cannot view 3D images even if you are wearing the 3D
Glasses.
Is the input image in 3D?
Check that the input image is 3D compatible.
Since most TV broadcasts do not contain a 3D format signal, 3D
reception must be set manually.
Is 3D Display set to Off?
If 3D Display is set to Off from the Configuration menu, the pro‐
jector does not automatically change to 3D even when a 3D im‐
button. s Signal - 3D Setup - 3D
age is input. Press the
Display p.68
Is the correct 3D format set?
The projector automatically selects the appropriate 3D format,
but if the 3D image is not displayed correctly, use 3D Format
from the Configuration menu to select another format. s Sig‐
nal - 3D Setup - 3D Format p.68
Are you viewing within the reception range? Check the range within which the 3D Glasses can communicate
with the projector, and view within that range. s p.47
Has pairing been performed correctly?
See the User's Guide for the 3D Glasses to perform pairing.
Are there any devices that cause radio wave
interference in the vicinity?
When using other devices at the same time with the frequency
band (2.4 GHz) such as Bluetooth communication devices, wire‐
less LAN (IEEE802.11b/g), or microwave ovens, radio wave inter‐
ference may occur, the image may be interrupted, or communi‐
cation may not be possible. Do not use the projector near these
devices.
The 3D image is enlarged and truncated
Check
Is the correct 3D video format set?
Remedy
Video may be truncated if an incorrect 3D format is set. Set the
correct 3D format. s p.45
Problems with HDMI
HDMI link does not function
Check
Are you using a cable that meets the HDMI
standards?
Remedy
Operations are not possible with cables that do not meet the
HDMI standards.
86
Troubleshooting
Check
Remedy
Does the connected device meet the HDMI
CEC standards?
If the connected device does not meet the HDMI CEC standards,
it cannot be operated even if it is connected to the HDMI port.
See the documentation and so on supplied with the connected
device for more information.
Also, press the
button, and then check if the device is
available under Device Connections. s p.61
Are the cables connected correctly?
Check that all the cables required to use HDMI Link are securely
connected. s p.61
Is the power for the amplifier or DVD recorder Put each device in standby status. See the documentation and
and so on turned on?
so on supplied with the connected device for more information.
Was a new device connected, or was the con‐ If the CEC function for a connected device needs to be set again,
nection changed?
for example when a new device is connected or the connection
is changed, you may need to restart the device.
Are many multi-media players connected?
Up to 3 multi-media players that meet the HDMI CEC standards
can be connected at the same time.
The device name is not displayed under Device Connections
Check
Does the connected device meet the HDMI
CEC standards?
Remedy
If the connected device does not meet the HDMI CEC standards,
it is not displayed. See the documentation and so on supplied
with the connected device for more information.
Problems with WirelessHD (EH-TW9200W/EH-TW8200W only)
Cannot project WirelessHD images
Check
Remedy
Does the cable connecting the supplied Wire‐ If the cable does not meet the HDMI standards, operations are
lessHD Transmitter meet the HDMI stand‐
not possible.
ards?
Is WirelessHD set to Off?
When WirelessHD is set to Off from the Configuration menu,
projection is not possible for WirelessHD input signals. Set Wire‐
button. s Settings lessHD to On, and then press the
WirelessHD p.70
Are signals being received within the Wire‐
lessHD transmission range?
Check the range within which the WirelessHD's transceiver can
communicate, and view within that range. s p.56
Is the supplied WirelessHD Transmitter
turned on?
Check the power lamp on the WirelessHD Transmitter. If there is
no power being supplied, make sure the connector for the AC
adapter is securely connected, and then turn on the power
switch.
Is the WirelessHD indicator for the supplied
WirelessHD Transmitter off?
The WirelessHD cannot communicate with the projector. Check
the range within which the WirelessHD's transceiver can com‐
municate, and setup within that range.
Is the Link indicator for the supplied Wire‐
lessHD Transmitter off?
No signal is output from the AV device connected to the Wire‐
lessHD Transmitter. Check that the cables from the AV device and
the WirelessHD Transmitter are securely connected.
87
Troubleshooting
Check
Remedy
Has dust collected in the WirelessHD's vent?
The vent on the base of the projector is the WirelessHD's vent.
Communication may not be possible if dust has collected in the
vent. Install the projector so that dust does not collect in the vent.
Are the projector and the WirelessHD Trans‐
mitter facing the correct way?
Setup the projector and the WirelessHD Transmitter so that they
are facing each other.
Interference, distortion, or interruption appear in WirelessHD
Check
Are signals being received within the Wire‐
lessHD transmission range?
Remedy
Check the range within which the WirelessHD's transceiver can
communicate, and view within that range. s p.56
Are there any obstructions between the Wire‐ Because WirelessHD communicates using a tight beamed elec‐
lessHD Transmitter and the projector?
tromagnetic wave, if there are any people or objects and so on
obstructing the communication path, this could have an adverse
affect on the image. Make sure that there are no obstacles be‐
tween the WirelessHD Transmitter and the projector within the
WirelessHD transmission range. s p.56
Is the reception too low?
If the transmissions are not strong enough, communication may
be unstable.
Check Reception as you set up the transmitter as it is sometimes
possible to improve the strength of the transmission by moving
the WirelessHD Transmitter or changing its direction. s Set‐
tings - WirelessHD - Reception p.70
Transmission strength may differ depending on the surround‐
ings, or they may be unstable. While checking Reception, setup
the transmitter in a location where the number displayed re‐
mains steady. s Settings - WirelessHD - Reception p.70
88
Maintenance
Maintenance
Cleaning the Parts
You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.
Warning
Do not use sprays that contain flammable gas to remove dirt and dust from the projector's lens, air filter,
and so on. The projector may catch fire due to the high internal temperature of the lamp.
Cleaning the air filter
Clean the air filter if dust has accumulated on the air filter or when the following message is displayed.
"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air
filter."
Attention
• If dust collects on the air filter, it can cause the internal temperature of the projector to rise, and this can lead
to problems with operation and shorten the optical engine's service life. It is recommended that you clean
the air filter at least once every three months. Clean them more often than this if using the projector in a
particularly dusty environment.
• Do not rinse the air filter in water. Do not use detergents or solvents.
• Lightly brush the air filter to clean it. If it is brushed too strongly, dust will be ground into the air filter and
cannot be removed.
a
Press the
button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Remove the air filter cover.
c
Hook your finger into the tab on the air filter
cover, and remove it from the lens side.
89
Remove the air filter.
Grip the knob in the center of the air filter
and pull it out at an angle.
Maintenance
d
Hold the air filter with the surface
facing down and tap it 4 or 5 times to
remove the dust.
f
Install the air filter.
g
Install the air filter cover.
Grip the air filter by the knob in the center
and insert it at an angle.
Turn it over and tap the other side in the
same way.
Secure the tab on the outside first, and then
secure the tab on the lens side.
Attention
If the air filter is hit too hard, it may
become unusable due to deformities
and cracks.
e
Remove any dust remaining on the air
filter by using a vacuum cleaner from
the front side.
Cleaning the main unit
Clean the projector's surface by wiping it gently with a soft cloth.
If it is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and
then firmly wring the cloth dry before using it to wipe the surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality
of the case may change or the paint may peel off.
90
Maintenance
Cleaning the lens
Use a commercially available cloth for cleaning glasses to gently
wipe off dirt from the lens.
Manually open the lens shutter, and then wipe the lens inside.
Attention
Do not rub the lens with harsh materials or handle the lens
too roughly as it can easily become damaged.
Cleaning the 3D Glasses
Use the cloth to gently wipe off dirt from the lenses of the 3D
Glasses.
Attention
• Do not rub the lenses of the glasses with harsh materials or
handle the lenses too roughly as they can easily become
damaged.
• When maintenance is necessary, disconnect the USB Charg‐
ing Adapter from the electrical outlet, and check that all ca‐
bles have been disconnected.
• The 3D glasses contain rechargeable batteries. Observe local
regulations when you dispose of them.
Replacement Periods for Consumables
Air filter replacement period
• If the message is displayed even though the air filter has been cleaneds p.89
Lamp replacement period
• The following message is displayed when projection starts
"It is time to replace your lamp. Please contact your Epson projector reseller or visit www.epson.com to
purchase."
• The projected image gets darker or starts to deteriorate.
c
• The lamp replacement message is set to appear after 3900 H in order to maintain the initial brightness
and quality of the projected images. The message display time changes depending on the usage
situation, such as the color mode setting and so on.
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp
may explode increases. When the lamp replacement message appears, replace the lamp with a new
one as soon as possible, even if it is still working.
• Depending on the characteristics of the lamp and the way it has been used, the lamp may become
darker or stop working before the lamp warning message appears. You should always have a spare
lamp unit ready in case it is needed.
91
Maintenance
Replacing Consumables
Replacing the air filter
c
Dispose of used air filters properly in accordance with your local regulations.
Material: Polypropylene
a
Press the
button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Remove the air filter cover.
c
d
Install the new air filter.
e
Install the air filter cover.
Grip the air filter by the knob in the center
and insert it at an angle.
Hook your finger into the tab on the air filter
cover, and remove it from the lens side.
Remove the old air filter.
Grip the knob in the center of the air filter
and pull it out an angle.
92
Secure the tab on the outside first, and then
secure the tab on the lens side.
Maintenance
Replacing the lamp
Warning
When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be
broken. If replacing the lamp of a projector that has been suspended from the ceiling, you should always
assume that the lamp is cracked, and remove the lamp cover with care. When you open the lamp cover,
small shards of glass could fall out. If any shards of glass get into your eyes or mouth, contact a doctor
immediately.
Caution
• Do not touch the lamp cover immediately after turning off the projector as it is still hot. Wait until the lamp
has cooled down sufficiently before removing the lamp cover. Otherwise, you could get burnt.
• We recommend the use of genuine EPSON option lamps. The use of non-genuine lamps may affect projection
quality and safety.
Any damage or malfunction caused by the use of non-genuine lamps may not be covered by Epson's warranty.
a
Press the
button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Loosen the lamp cover fixing screw.
c
Remove the lamp cover.
Slide the lamp cover straight forward and
remove it.
93
d
Loosen the two lamp fixing screws.
e
Remove the old lamp.
Grip the knob firmly and pull it straight out.
Maintenance
f
Install the new lamp.
g
Tighten the two lamp fixing screws.
Make sure the lamp is facing the correct
direction and press it in.
h
Replace the lamp cover.
i
Tighten the lamp cover fixing screw.
Slide the cover back into place.
Warning
Do not disassemble or remodel the lamp. If a modified or disassembled lamp is installed in the projector
and used, it could cause a fire, electric shock, or an accident.
Caution
• Make sure you install the lamp and lamp cover securely. If they are not installed correctly, the power does
not turn on.
• The lamp contains mercury (Hg). Dispose of used lamps in accordance with your local laws and regulations
on disposing of fluorescent tubing.
Resetting lamp hours
After replacing the lamp, make sure you reset the lamp hours.
The projector records how long the lamp is turned on and a message and indicator notify you when it is time
to replace the lamp.
a
Turn on the power.
b
Press the
button.
The Configuration menu is displayed.
94
Maintenance
c
d
Select Reset - Reset Lamp Hours.
A reset confirmation message is displayed.
Use the
buttons to select Yes,
and then press the
button to
execute.
The lamp hours are reset.
95
Appendix
Optional Accessories and Consumables
The following optional accessories/consumables are available for purchase if required. This list of optional
accessories/consumables is current as of: 2013.6. Details of accessories are subject to change without notice.
Varies depending on country of purchase.
Optional Items
Name
Ceiling mount*
Model No.
ELPMB30
Explanation
Use when installing the projector on a ceiling.
ELPMB22
ELPMB20
Ceiling pipe 600 (600 mm white)*
ELPFP07
Ceiling pipe 450 (450 mm white)*
ELPFP13
Ceiling pipe 700 (700 mm white)*
ELPFP14
RF system 3D Glasses
ELPGS03
Use when viewing 3D images.
Cable cover
ELPCC04B
(Black),
ELPCC04W
(White)
Use this when installing the projector on a ceiling
to cover the cables and improve the overall ap‐
pearance.
Do not attach the cable cover when the cable is
secured with an HDMI cable clamp.
Use when installing the projector on a high ceil‐
ing.
USB Charging Adapter
ELPAC01
Use when charging the 3D Glasses.
* Special expertise is required to suspend the projector from a ceiling. Contact your local dealer.
Consumables
Name
Model No.
Explanation
Lamp unit
ELPLP69
Use as a replacement for used lamps. (1 lamp)
Air filter
ELPAF39
Use as a replacement for used air filters. (1 air filter)
96
Appendix
Supported Resolutions
Component Video
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (480i)
60
720 x 480
SDTV (576i)
50
720 x 576
SDTV (480p)
60
720 x 480
SDTV (576p)
50
720 x 576
HDTV (720p)
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
HDTV (1080p)
50/60
1920 x 1080
Composite Video
Signal
Refresh Rate (Hz)
Resolution (dots)
TV (NTSC)
60
720 x 480
TV (SECAM)
50
720 x 576
TV (PAL)
50/60
720 x 576
Computer Signals (Analog RGB)
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60/72/75/85
640 x 480
SVGA
56/60/72/75/85
800 x 600
XGA
60/70/75/85
1024 x 768
SXGA
70/75/85
1152 x 864
60/75/85
1280 x 960
60/75/85
1280 x 1024
60
1280 x 768
60
1366 x 768
60/75/85
1280 x 800
60
1600 x 900
WXGA
WXGA++
HDMI1/HDMI2 Input Signal
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640 x 480
SDTV (480i)
60
720 x 480
97
Appendix
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (576i)
50
720 x 576
SDTV (480p)
60
720 x 480
SDTV (576p)
50
720 x 576
HDTV (720p)
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
HDTV (1080p)
24/50/60
1920 x 1080
3D Input Signal
Signal
Refresh Rate Resolution (dots)
(Hz)
3D Format
Frame Pack‐
ing
Side by Side
Top and Bot‐
tom
HDTV750p (720p)
50/60
1280 x 720
HDTV1125i (1080i)
50/60
1920 x 1080
-
-
HDTV1125p
(1080p)
50/60
1920 x 1080
-
-
HDTV1125p
(1080p)
24
1920 x 1080
WirelessHD Input Signal
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640 x 480
SDTV (480i)
60
720 x 480
SDTV (576i)
50
720 x 576
SDTV (480p)
60
720 x 480
SDTV (576p)
50
720 x 576
HDTV (720p)*
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
HDTV (1080p)*
24/50/60
1920 x 1080
* When projecting in WirelessHD, the following signals do not support Deep Color.
2D: 1080p 60/50 Hz
3D: 1080P 24 Hz frame packing/720P 50/60 Hz frame packing/1080p 60/50 Hz side by side
3D Input Signal MHL (via a WirelessHD Transmitter*)
Signal
Refresh Rate Resolution (dots)
(Hz)
3D Format
Frame Pack‐
ing
HDTV750p (720p)
50/60
1280 x 720
-
HDTV1125i (1080i)
50/60
1920 x 1080
-
98
Side by Side
Top and Bot‐
tom
-
Appendix
Signal
HDTV1125p
(1080p)
HDTV1125p
(1080p)
* HDMI5 port only
Refresh Rate Resolution (dots)
(Hz)
3D Format
Frame Pack‐
ing
Side by Side
Top and Bot‐
tom
-
-
50/60
1920 x 1080
-
24
1920 x 1080
-
99
Appendix
Specifications
Product name
EH-TW9200W/EH-TW8200W
EH-TW9200/EH-TW8200/EHTW7200
Appearance (not including ad‐ 466 (W) x 140 (H) x 395 (D) mm
justable foot)
Panel Size
0.74" wide
Display method
Polysilicon TFT active matrix
Resolution
1920 (W) x 1080 (H) x 3
Scanning
Frequency
Digital
Pixel Clock: 13.5 - 148.5 MHz
Horizontal: 15.6 - 67.5 kHZ
Vertical: 24, 50 - 60 Hz
Analog
Pixel Clock: 13.5 - 157.5 MHz
Horizontal: 15.6 - 91.2 kHZ
Vertical: 50 - 85 Hz
Focus adjustment
Manual
Zoom adjustment
Manual (approx. 1 to 2.1)
Lamp (light source)
UHE lamp 230 W, Model No.: ELPLP69
Power supply
100 - 240 V AC ±10%, 50/60 Hz, 3.7 - 1.6 A
Power con‐ 100 to 120 V area Operating: 350 W
sumption
Standby power consumption: 0.24 W
Standby power consumption: 7.1 W*
220 to 240 V area Operating: 334 W
Standby power consumption: 0.34 W
Standby power consumption: 8.1 W*
Operating altitude
Altitude 0 to 2286 m
Operating temperature
+5 to 35°C (No condensation)
Storage temperature
-10 to +60°C (No condensation)
Mass
Approx. 8.6 kg
Connectors
Component port x 1, 3RCA pin jack
Approx. 8.4 kg
PC port x 1, Mini D-Sub15-pin (female) blue
HDMI port x 2, HDMI
For HDCP, For CEC signals, Deep Color
Video port x 1, RCA pin jack
RS-232C port x 1, D-sub 9-pin (male)
Trigger out port x 1, 3.5 mm mini jack
Mini USB TypeB port x 1
* When using the WirelessHD Transmitter with EH-TW9200W/EH-TW8200W, and the following conditions are
satisfied
Settings - WirelessHD - WirelessHD - On
Settings - HDMI Link - Power On Link is set to Bidirectional or Device -> PJ s p.70
100
Appendix
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Обладнання відповідає вимогам Технічного регламенту обмеження використання деяких небезпечних
речовин в електричному та електронному обладнанні.
Angle of tilt
If you use the projector tilted at an angle of more than 4°, it could be dam‐
aged or cause an accident.
ESC/VP21 Commands
Use of ESC/VP21 enables control of the projector from an external device. For more details, see the following
Web site.
http://www.epson.com
RS-232C Cable layouts
• Connector shape: D-sub 9-pin (male)
• Projector input port name: RS-232C
• Signal name:
Signal Name
Function
GND
Signal wire ground
TD
Transmit data
RD
Receive data
<At the projector>
<At the projector>
<At the computer>
(PC serial cable)
• Communications protocol
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
Flow control: None
101
<At the computer>
Appendix
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-981-3840
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the
FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and
found to be compliant with the standards. Records maintained continue to reflect the equipment being
produced can be expected to be within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Trade Name:
EPSON
Type of Product:
LCD Projector
Model:
H585C/H586C/H587C/H588C/H589C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures.
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification or Declaration of this device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than one interface connector, do not
leave cables connected to unused interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
102
Appendix
Glossary
This section briefly explains the difficult terms that are not explained in context in the text of this guide. For
details, refer to other commercially available publications.
HDCP
HDMI
™
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to pre‐
vent illegal copying and protect copyrights by encrypting digital signals sent over DVI and
HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital
images protected by HDCP technology. However, the projector may not be able to project
images protected with updated or revised versions of HDCP encryption.
An abbreviation for High Definition Multimedia Interface. This is the standard by which
HD images and multichannel audio signals are digitally transmitted.
™
HDMI is a standard aimed at digital consumer electronics and computers. By not com‐
pressing the digital signal, the image can be transferred at the highest quality possible. It
also provides an encryption function for the digital signal.
HDTV
An abbreviation for High-Definition Television. This refers to high-definition systems
which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = Progressive, i = Interlace)
• Screen aspect of 16:9 Dolby Digital audio reception and playback (or output)
MHL
An abbreviation for Mobile High-definition Link, which is a standard high-definition in‐
terface that enables high-speed transfer of video signals on mobile devices.
It is a standard targeting smartphones and tablets that transfers uncompressed digital
signals without loss of quality and also enables simultaneous charging of such devices.
NTSC
An abbreviation for the National Television Standards Committee. A terrestrial analog
color broadcasting method. This method is used in Japan, North America, and Latin Amer‐
ica.
PAL
An abbreviation for Phase Alternation by Line. A terrestrial analog color broadcasting
method. This method is used in various Western European countries (with the exception
of France), Asian countries such as China, and Africa.
SDTV
An abbreviation for Standard Definition Television. This refers to standard television sys‐
tems which do not satisfy the conditions for HDTV High-Definition Television.
SECAM
An abbreviation for SEquential Couleur A Memoire. A terrestrial analog color broadcasting
method. This method is used in France, Eastern Europe, the former Soviet Union, the
Middle East, Africa, and so on.
SVGA
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
SXGA
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
VGA
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
YCbCr
In component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the
color difference.
YPbPr
In component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the
color difference.
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio
of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
103
Appendix
Interlace
Transmits information needed to create one screen by sending every other line, starting
from the top of the image and working down to the bottom. Images are more likely to
flicker because one frame is displayed every other line.
Pairing
Register devices in advance when connecting with Bluetooth devices to ensure mutual
communication.
104
Appendix
General Notes
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting from the use of the infor‐
mation contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties
for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options
or any consumable products other than those designated as Original Epson Products or Epson Approved Prod‐
ucts by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related
to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/
precision devices etc, you should use this product only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system reliability. Because this product was not
intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main
communication equipment, nuclear power control equipment, or medical equipment related to direct medical
care etc, please make your own judgment on this product’s suitability after a full evaluation.
105
Appendix
General Notice
EPSON and ELPLP are the trademarks or registered trademarks of Seiko Epson Corporation.
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing
LLC.
WirelessHD, WiHD, and the WiHD logo are trademarks or registered trademarks of WirelessHD LLC.
THX and the THX 3D logo are trademarks of THX Ltd. which may be registered in some jurisdictions. All rights
reserved.
™ logo and Full HD 3D Glasses™ are trademarks of the Full HD 3D Glasses Initiative™.
The Full HD 3D Glasses
InstaPrevue and the InstaPrevue logo are the trademarks or registered trademarks of Silicon Image, Inc.
®
Bluetopia® is provided for your use by Stonestreet One, LLC® under a software license agreement. Stonestreet
One, LLC® is and shall remain the sole owner of all right, title and interest whatsoever in and to Bluetopia® and
your use is subject to such ownership and to the license agreement. Stonestreet One, LLC® reserves all rights
related to Bluetopia® not expressly granted under the license agreement and no other rights or licenses are
granted either directly or by implication, estoppel or otherwise, or under any patents, copyrights, mask works,
trade secrets or other intellectual property rights of Stonestreet One, LLC®.
© 2000-2012 Stonestreet One, LLC® All Rights Reserved.
Bluetooth and the Bluetooth logo are the trademarks of Bluetooth SIG, Inc.
MHL and the MHL logo are a trademark, registered trademark or service mark of MHL, LLC in the United States
and/or other countries.
Other product names used herein are also for identification purposes only and may be trademarks of their
respective owners. Epson disclaims any and all rights in those marks.
©SEIKO EPSON CORPORATION 2013. All rights reserved.
106
Index
Connecting WirelessHD devices .............. 20
Contrast ............................................................ 66
Control panel ................................................ 8, 9
Control panel lock ......................................... 71
Cool-down ....................................................... 26
2
2D-to-3D Conversion ................................... 68
3
3D brightness .................................................
3D depth ...........................................................
3D display .........................................................
3D Format ........................................................
3D format .........................................................
3D Glasses ........................................................
3D Glasses charging port ...........................
3D images ........................................................
3D settings .......................................................
3D viewing notice .........................................
68
68
68
75
68
45
52
45
68
68
D
Deep color ........................................................ 75
Deinterlacing .................................................. 68
Device Connections .............................. 70, 71
Device connections ...................................... 56
Diagonal Screen Size .................................... 68
Direct power on ............................................. 73
Display background ..................................... 74
Display settings .............................................. 74
Displaying the test pattern ........................ 27
A
E
Adjusting focus .............................................. 27
Adjusting RGB ................................................. 35
Adjusting the tilt ............................................ 28
Advanced .................................................. 67, 69
Air filter .............................................................. 89
Air filter cover .......................................... 89, 92
Air filter replacement period ..................... 91
Appearance ..................................................... 16
Aspect ......................................................... 31, 68
Auto iris ...................................................... 38, 67
Auto setup ....................................................... 69
EPSON Super White ...................................... 67
Erase memory .......................................... 43, 75
Error/Warning indicators ............................ 77
Exit Picture in Picture ................................... 76
Extended menu .............................................. 73
F
Focus .................................................................. 82
Focus adjustment .......................................... 27
Focus ring .................................................... 8, 27
Frame Interpolation ..................................... 69
Full ...................................................................... 31
B
Brightness .......................................... 33, 66, 67
G
C
Gain ............................................................. 35, 67
Gamma ....................................................... 34, 67
CEC standards ................................................. 61
Child lock .......................................................... 71
Cleaning the 3D Glasses ............................. 91
Cleaning the air filter .................................... 89
Cleaning the lens ........................................... 91
Cleaning the main unit ................................ 90
Color Gamut .................................................... 67
Color mode ............................................... 30, 66
Color saturation ............................................. 66
Color Temp. ..................................................... 66
Component ..................................................... 74
Component port ............................................ 19
Configuration menu ..................................... 65
Connecting ...................................................... 19
Connecting a computer .............................. 20
Connecting MHL compatible devices
................................................................................ 21
Connecting smartphones or tablets ...... 21
Connecting video equipment .................. 19
H
HDMI Link ......................................................... 70
HDMI link .......................................................... 61
HDMI port ......................................................... 61
HDMI Video Range ........................................ 69
HDMI1 port ........................................ 19, 20, 21
HDMI2 port ............................................... 19, 20
High altitude mode ...................................... 73
Hue .............................................................. 33, 67
I
Illumination .....................................................
Image .................................................................
Image menu ....................................................
Image Processing ..........................................
Indicators ..........................................................
107
73
30
66
69
77
Index
Info menu ......................................................... 75
Input signal ............................................... 74, 75
Inverse 3D Glasses ......................................... 68
Projection ......................................................... 72
Projection size ......................................... 18, 28
R
K
Reception .................................................. 56, 71
Refresh rate ...................................................... 75
Remote Control .............................................. 11
Remote control .............................................. 23
Rename Device Name ................................. 71
Rename memory .................................... 43, 75
Replacement periods for consumables
................................................................................ 91
Replacement time ......................................... 91
Replacing consumables .............................. 92
Replacing the air filter .................................. 92
Replacing the lamp ....................................... 93
Reset ....................................... 67, 70, 71, 72, 74
Reset all ............................................................. 75
Reset lamp hours .................................... 75, 94
Reset memory .......................................... 43, 75
Reset menu ...................................................... 75
Resolution ........................................................ 75
RGB ..................................................................... 67
RGBCMY ..................................................... 33, 67
Keystone .................................................... 29, 70
Keystone distortion ...................................... 29
L
Lamp cover ................................................. 8, 93
Lamp cover fixing screw ............................. 93
Lamp hours ...................................................... 75
Lamp replacement period ......................... 91
Language ......................................................... 74
Link indicator .................................................. 52
Load memory ........................................... 43, 75
Lock setting ..................................................... 71
M
Memory function ...........................................
Memory menu ................................................
Menu ..................................................................
Menu color .......................................................
Menu position ................................................
Messages ..........................................................
Model no. display mode .............................
Motion detection ...........................................
42
75
65
74
74
74
74
68
S
Saturation .................................................. 33, 67
Save memory ........................................... 42, 75
Scan mode ....................................................... 75
Select Color ...................................................... 74
Serial number ................................................. 75
Settings menu ................................................ 70
Setup level ....................................................... 69
Sharpness .................................................. 37, 66
Signal menu .................................................... 68
Skin tone ........................................................... 66
Sleep mode ...................................................... 73
Source ......................................................... 26, 75
Specifications ............................................... 100
Standby confirmation .................................. 74
Start Adjustments ......................................... 74
Startup screen ................................................ 74
Status ................................................................. 75
Sub menu ......................................................... 65
Sub-screen ....................................................... 59
Subscreen Position ....................................... 76
Subscreen Size ................................................ 76
Subscreen Source .......................................... 76
Super-resolution ............................................ 69
Supported resolutions ................................. 97
Swap Main/Sub .............................................. 76
Sync info ........................................................... 75
N
Noise .................................................................. 83
Noise reduction .............................................. 69
O
Offset .......................................................... 35, 67
Operating range ............................................ 24
Operating time ............................................... 94
Operation ......................................................... 73
Overscan ........................................................... 69
P
Pairing ............................................................... 46
Panel Alignment ............................................ 74
Pattern Color ................................................... 74
PC port ............................................................... 20
Picture in Picture .................................... 63, 76
Position ............................................................. 68
Power ................................................................. 26
Power consumption ..................................... 67
Power Off Link ................................................ 70
Power On Link ................................................ 70
Power supply .................................................. 25
108
Index
Sync. ................................................................... 68
T
Tint ......................................................................
Top menu .........................................................
Tracking ............................................................
Transmission range ......................................
Trigger Out ......................................................
66
65
68
56
73
U
User button ...................................................... 72
V
Version .............................................................. 75
Video port ........................................................ 19
Video signal .............................................. 74, 75
Viewing area .................................................... 47
W
WiHD indicator ............................................... 52
WiHD Mode ..................................................... 71
WirelessHD ................................................ 52, 71
Z
Zoom .................................................................. 31
Zoom adjustment ......................................... 28
Zoom ring ........................................................... 8
109
Download PDF