XR Super 6 User Manual
XRSuper6
User’s Guide
Silencing an Alarm
All/Perimeter and Home/Away Systems
1. While the alarm bell or siren is sounding, enter your user code. The keypad displays DISARM
SILENCE.
2. Press the SELECT key under SILENCE to stop the bell or siren. This does NOT disarm the system.
3. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.
Copyright © 1996 - 2001 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
PENDING The XRSuper6 panel is UL listed for Grade A Household Service as well as Commercial Burglary Service PENDING
Security Command® User's Guide
XRSuper6 Command ProcessorTM Panels
Table of Contents
Section
Page
About Your Security System ................................... 1
The Security Command Keypad .............................. 2
Special Security Command Messages ........................ 3
Special Security Command Tones ............................ 3
Understanding Security System Terms ....................... 4
Understanding Security System Terms ....................... 5
How your System Operates ................................... 6
All/Perimeter System Arming ................................. 7
All/Perimeter System Disarming ............................. 8
Home/Away System Arming ................................... 9
Home/Away System Disarming .............................. 10
Security Command User Menu ............................... 11
User Check-in ................................................... 11
Zone Activity Check ............................................ 11
Sensor Reset .................................................... 12
Outputs On Off ................................................ 12
Bypass Zones ................................................... 13
Zone Monitor ................................................... 13
System Test ..................................................... 14
User Codes ...................................................... 15
Ambush Codes .................................................. 16
Date and Time .................................................. 17
Section
Page
Display Events .................................................. 18
Zone Activity Check Event Display .......................... 18
Zone Bypass Event Displays .................................. 19
Zone Event Displays ........................................... 19
Arming and Disarming Event Displays ...................... 20
User Checkin Event Displays ................................. 20
User Code Change Event Displays ........................... 20
Supervisory Event Displays ................................... 20
System Monitor Event Displays .............................. 21
Service Request? ............................................... 21
System Setup ................................................... 22
Protection Areas ............................................... 22
Outputs .......................................................... 22
User Codes ...................................................... 23
Easy Entry™ User's Guide ..................................... 24
Arming and Disarming ......................................... 25
Entry Delay ..................................................... 25
FA113 User's Guide ............................................ 26
Pager Direct™ User's Guide ................................... 27
PhoneAccess™ User's Guide .................................. 29
895 Voice Module .............................................. 30
Index ............................................................. 31
i
This page intentionally left blank.
Introduction
About Your Security System
Keypad User Menu
Your Security Command system has been designed with your
safety and comfort in mind. It uses the latest in computer
technology to create the most user friendly security and fire
system on the market today.
The keypad also supplies a User Menu containing all of the
functions you need to fully operate your system, such as the
ability to change a personal user code number.
The system combines ease of use with a simple to understand
Security Command keypad display to offer the full range of
features requested by today’s security system owners. Security
Command can protect both the interior and perimeter of your
home or business while you are away or just the perimeter when
you are inside giving you a wall of security and peace of mind.
One of the most important concerns facing the security industry
today is false alarms. The accidental dispatching of police and fire
agencies places others in jeopardy by limiting the response
capability of those emergency service units.
A Note About False Alarms
You can turn portions of your protection on or off at any time by
pressing a few buttons. You can add, delete, and change personal
user codes at any time or check the status of all protection
devices in the system.
As part of our commitment to reducing false alarms, we would like
to encourage you to read this guide thoroughly. All the information
contained here can help you quickly, and comfortably, learn the
operation of the Security Command system. If you have any
additional questions, or feel that you need more training, please
do not hesitate to contact us.
Parts of the System
Test Your System Weekly
There are two main parts to the Security Command system, the
Security Command keypad and the keypad User Menu.
Security Command keypad
This is the device we have placed at certain locations throughout
the premises that allow you to turn the system’s protection on
and off using your personal user code number.
Introduction
It is recommended that you test the burglary portion of your
system at least once each week. Testing should involve an active
test of all doors, windows, and motion detectors connected to
your system. If your system also has fire protection, call the
service department to find out how this portion of your system
should be tested.
Refer to the System Test section of this guide for instructions on
testing the burglary portion of your system.
1
The Security Command Keypad
Your system may have one or more easy-to-use Security Command
keypads (16 or 32-character) that allow you to properly operate
the system. The illustration and descriptions below highlight some
of the keypad features:
32-Character Keypad
AC
LED
ARMED
LED
POWER
JONES RESIDENCE
F R I 2 : 51 AM
ARMED
Lighted display
SELECT keys
1
2
AB C
5
3
DEF
6
MN O
9
JKL
8
7
PQR
0
Data Entry keys
4
GHI
S TU
COMMAND key
VWX
COMMAND
YZ
ARROW key
16-Character Keypad
Lighted display
SELECT keys
AC LED
1
3
2
5
6
MNO
9
POWER
JKL
Data Entry keys
8
7
PQR
0
4
GHI
DEF
ABC
STU
VWX
COMMAND
YZ
COMMAND key
Data Entry keys
These keys allow you to enter your user code when arming or
disarming and enter other information into the system.
The ARROW key
The ARROW key is used to go back through the keypad displays
while operating your system. You can press the ARROW key to
back up through the list of functions in the User Menu or to make
a correction by erasing the last character you entered.
The COMMAND key
The COMMAND key allows you to advance through the keypad
displays or User Menu or complete a data entry function.
AC LED
This LED remains on steady as long as your system is connected to
its AC power supply. Should there be an interruption, the LED
turns off and the system's backup battery maintains normal
operation for a time allowing you to contact our service department.
ARMED LED
This LED is ON steady anytime burglary protection is armed and
OFF when ALL areas are disarmed.
32-Character Keypad User Options Menu
Press and hold the ARROW and COMMAND keys for about two
seconds. The keypad display shows SET BRIGHTNESS. Use the left
SELECT key to lower the display brightness. Use the right SELECT
key to increase the display brightness. Press COMMAND.
The SELECT keys
At SET TONE, use the left SELECT key to lower the keypad tone.
Use the right SELECT key to raise the keypad tone. Press
COMMAND.
There are four keys under the display called the SELECT keys.
These keys are one of the features that make your system so easy
to operate. They allow you to choose what to do by pressing the
SELECT key under choices being shown in the display.
At SET VOLUME LEVEL, use the left SELECT key to lower the
keypad volume. Use the right SELECT key to raise the keypad
volume. Press the ARROW key to exit out of the User Options
menu.
ARROW key
2
Introduction
Special Security Command Messages
Special Security Command Tones
As you use your system, you will occasionally see a keypad display
that asks you to enter a user code or that describes a condition
on the system. Below are some examples of those displays.
Your keypad also contains a small speaker that allows it to alert you
to events as they occur on your system. Below are brief
descriptions of the different tones you will hear from the keypad:
ALARM
A 24-hour zone, such as a fire or panic zone, or an armed burglary
zone has been faulted. Your system may sound bells or sirens.
Fire alert: Your keypad may sound a fire tone to alert persons in
the vicinity to the alarm condition. This is in addition to the bell
output from the alarm panel.
ALARM CANCELLED
This message displays when an authorized user has cancelled an
alarm condition by entering a valid user code and an “Alarm
Cancelled” report was sent to the central station.
Burglary alert: Your keypad may sound a burglary tone to alert
persons in the vicinity to the alarm condition. This is in addition
to the bell output from the alarm panel.
TROUBLE
There is a problem with a protection device or system component.
This display is accompanied by a description of the problem.
Prewarn tone: A continuous pulsed tone that sounds when you
open an entry delay door on a system that is armed (turned on)
reminding you to disarm the burglary protection.
ENTER CODE
The system requires you to enter a personal user code. User
codes can be required for turning your system on (arming),
turning your system off (disarming), and other system options.
Monitor tone: A short tone that sounds for one second whenever
a door or window is opened while you are using the zone monitor
function from the User Menu. See Zone Monitor.
As you enter your user code, the keypad display shows an asterisk
(*) in place of each digit pressed. This prevents others from seeing
your user code on the display as it is entered.
TRY AGAIN
The user code entered is not recognized by the system. Check the
user code and try again.
INVALID CODE
The user code you have entered is considered invalid by the
system.
SYSTEM TROUBLE or SERVICE REQUIRED
There is an electronic failure in your system. Contact the service
department as soon as possible.
Introduction
Key press tone: A short beep as you press a key on the keypad.
Trouble tone: A steady tone indicating a trouble condition on
your system. Press a SELECT key to silence the trouble tone.
Zone Activity Check tone: A steady tone indicating no zone
activity has occurred on your system within the programmed
period of time. Press any key to silence the tone.
What to do when the trouble tone is sounding
You can silence the trouble tone by pressing any one
of the top row SELECT keys. This only silences the
keypad and does not correct the condition that
originally caused the problem.
3
Understanding Security System Terms
Entry or Exit Zone
Throughout this guide and in some displays on your keypad, you will
see certain words or phrases that might be unfamiliar. Although
every effort has been made to use terms that are commonly known,
there are some for which there is no acceptable substitute.
Almost all systems have one or more doors through which you can
enter or exit the premises. These doors are programmed with a
delay time to allow you to enter or exit while the system is armed
without setting off the alarm.
Below are some terms you will see here and on your keypad display.
When you arm the system, activity on all burglary zones is ignored
until the programmed exit delay time expires. Once that time has
expired and the system is fully armed, opening the door causes the
panel to start the entry delay time. During the entry delay time,
you must enter a valid user code to disarm the system or an alarm
will occur.
Arming
This is the term used for turning on the burglary protection in one
or more areas of the system. Your system may require you to enter
a user code. When armed, the system is able to sound alarm bells
or sirens and, if monitored, send alarm reports to a central station
when a burglary zone is faulted.
Fire, panic, and other 24-hour devices are always turned on and do
not need to be armed.
Disarming
This means turning off one or more areas of the system. When
disarmed, the system does NOT sound alarms or send alarm reports
to a central station when a burglary zone is faulted.
Zone
A zone refers to a group of one or more protected openings or
protection devices assigned the same zone number. Each door or
window, motion detector, smoke detector, or other device has a
zone number and a name.
Often, similar devices in the same general area will share the same
zone. For example, the windows on the east side of the premises
can all be grouped together in a zone named E. WINDOWS.
4
Instant Zone
Exterior windows and non-entry doors, or interior protection
devices, are typically not programmed with delay times. If these
zones are faulted while the system is armed, an alarm occurs
instantly.
24-Hour Zone
A 24-hour zone is never assigned to an area and is not turned on
or off by arming or disarming your system. Some examples of 24hour zones are fire zones, panic zones, and temperature control
zones.
Areas
An area is made up of burglary zones that can be armed or disarmed
together. The Perimeter area, for example, consists of all the
doors and windows on the outside of the building. When you arm
the Perimeter, these zones sound an alarm if tripped.
Introduction
Understanding Security System Terms
Status List
Central Station Monitoring
The keypad Status List displays any alarm or trouble condition on
a zone and any trouble condition that occurs with the AC power
or battery power. If more than one alarm or trouble condition
occurs at the same time, the keypad sequences this information
on its display.
Your system can also be programmed to automatically send alarm,
trouble, and arming and disarming reports to a central station.
Operators at the central station can then dispatch the appropriate
authorities or contact you with the specific event information.
Status
If your system contains any Panic zones, these are not displayed
on the keypad for security reasons.
Status is a feature that automatically displays the armed or
disarmed status of your system on the Security Command keypads.
Alarm or trouble conditions on a zone or a system monitor such as
AC or battery trouble can also be displayed. There are two types
of status information available: Armed Status and Status List.
If an alarm occurs on a non-fire 24-hour zone or a system monitor,
it remains in the Status List until it restores. If one or more armed
burglary zones trips, the last one to trip remains in the Status List.
The burglary zone alarm remains in the Status List for several
minutes or until it is cleared by disarming the system.
Armed Status
With Armed Status, the keypad displays the current armed condition
of areas within your security system.
The keypad displays
When
HOME MODE ON
The perimeter areas are on
ALL SYSTEM ON
All areas are on
SLEEP MODE ON
The perimeter and interior areas are on
but the bedroom area is off
Also, for keypads that include an Armed LED, the Armed LED is ON
steady anytime a burglary protection area is armed and OFF when
ALL areas are disarmed.
Exit Error
This is an automatic function of the panel that prevents an alarm
from occurring if an exit door does not close all the way after the
system has been armed. Here is how it works:
You close all doors and windows, arm the system, and then leave
by the front door. You close the door but it does not latch and
opens slightly causing the front door zone to show as an open to
the system. After the exit delay time expires the system attempts
to arm the front door zone but recognizes the open condition
and, instead of sending an alarm report to the central station,
sends an Exit Error report and force arms the door. (If the door
closes at a later time it will be included back into the system.) The
system sounds the alarm sirens for 15 seconds to alert you of the
condition and provide an opportunity for you to close the door.
The Exit Error feature allows the central station to acknowledge
the arming error without dispatching the police on a false alarm.
Introduction
5
How your System Operates
Your system has been programmed to operate in one of two
modes: All/Perimeter, or Home/Sleep/Away.
• All/Perimeter - Your burglary protection is divided into two
areas: Interior and Perimeter. You can turn on the just the
Perimeter protection while inside for security or turn on both as
you leave.
• Home/Sleep/Away - Your burglary protection is divided into
three areas: Interior, Perimeter, and Bedrooms. You can turn on
the Perimeter, Perimeter and Interior, or all three areas separately.
Regardless of which mode has been programmed, much of the
operation is similar. Throughout this guide, any differences
between the systems are noted for your convenience.
Arming Functions
After making your arming selection, the keypad displays any zones
that are currently bypassed. These zones remain bypassed until
the system is armed and then disarmed. Any 24-hour zones in a
faulted condition are also displayed.
During arming, the system verifies that all doors, windows, and
other protection devices to be armed are in normal condition.
If everything is alright (normal), the system arms. If there is a
problem on one or more burglary zones the keypad displays the
problem and allows you to bypass those zones.
In some cases, you might see the keypad display FRONT DOOR BAD
*. The asterisk next to BAD means that the zone is a priority zone,
which cannot be bypassed. The problem on the zone must be
corrected before the system can be armed.
Armed Message: After all bypassing is completed or zone faults
corrected, the areas you selected are armed. The keypad briefly
displays ALL SYSTEM ON if all areas in the system are arming and
HOME MODE ON or SLEEP MODE ON if only selected areas are
arming. The keypad then displays the exit delay as it counts down.
Zones are not armed until the exit delay time expires.
If your system uses a keyswitch to arm an area, the exit delay time
is NOT shown on the keypad display.
DIALING . . . Message: If your system is monitored, it may be
programmed to wait for the arming report to be sent to the
central station before displaying the armed message. (See Arming
Report below.) This is to verify your phone lines are working
properly. While the system is waiting, the display reads DIALING....
If the report is received, the keypad buzzes for one second and
displays the armed message. If the report is not received, the
keypad displays LOCAL ALARM ONLY before displaying the armed
message.
Arming Report: Your system can be programmed to send arming
or zone bypass reports to a central station. This feature is optional
and can be programmed for you at any time.
If the problem can be corrected by closing a door or window, do
not bypass the zone. Instead, correct the problem and try arming
again. If the problem cannot be corrected, you can bypass the
zone or wait until the zone can be repaired by a service
technician. A bypassed zone is ignored by the system during the
armed period.
6
Introduction
All/Perimeter System Arming
Area Assignment: Your security system is divided into two
separate areas. Motion detectors, inside doors, and other interior
protection devices are assigned to the Interior area while
windows and exterior doors are assigned to the Perimeter area.
Perimeter or All: When arming an All/Perimeter system, the
keypad displays PERIM
ALL. If you select ALL, you arm both
the Perimeter and the Interior of the system. You will want to arm
both of these areas when leaving with nobody left inside.
Selecting PERIM arms only the Perimeter of the system. Perimeter
arming is for when you are staying inside but want the comfort of
knowing the exterior doors and windows are armed. Perimeter
arming allows you to move freely about inside without setting off
any interior alarms.
Arming an All/Perimeter System
1. Enter your code. The keypad displays
PERIM
ALL.
2. Select PERIM to arm the Perimeter area only.
3. Select ALL to arm both the Perimeter and Interior areas.
4. The keypad displays any bypassed zones and 24-hour zones
that are in a bad condition. No action is required by you.
5. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it
later returns to normal. A zone that is bypassed will remain
bypassed until the system is disarmed. See steps 5a through
5d.
5a. If a problem exists on any zones, the zone name and
problem are shown followed by: OKAY BYPASS STOP.
System Ready/System Not Ready Keypad
Displays
5b. Select OKAY to force arm the zone(s) before arming.
When all zones in the system are in a normal condition, the keypad
displays SYSTEM READY. If there are one or more zones that are
not in a normal condition, the keypad displays SYSTEM NOT
READY. Pressing any top row SELECT key during this display shows
the zone name allowing you to investigate the problem.
5d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
Instant Arming
Instant: During the exit delay time, you can cancel the exit and
entry delays and cause all zones to be instant zones. Press the far
right select key under INSTNT while the exit delay is displayed.
This immediately arms the exit zones. However, no entry delay is
provided and an alarm will occur should an entry door be opened.
Arming and Disarming
5c. Select BYPASS to bypass the zone(s) before arming.
6. The keypad displays PERIMETER ON if only the perimeter is
being armed and ALL SYSTEM ON if both the perimeter and
interior are being armed.
7. The keypad next displays EXIT: ## INSTNT and begins to count
down the number of seconds remaining for you to exit. When
the delay expires, all zones are armed.
8. You can select INSTNT while EXIT: ## INSTNT is displayed to
immediately arm all zones and make them instant. The keypad
displays INSTANT.
9. When the system is fully armed, the keypad displays PERIMETER
ON for perimeter arming and ALL SYSTEM ON for perimeter
and interior arming.
7
All/Perimeter System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an
alarm. After opening the door, the Security Command keypad
sounds a prewarn tone to remind you to disarm the system. You
must disarm the system before the prewarn tone expires or an
alarm on the door zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter
your user code to disarm the system.
Alarm Display: After disarming, the keypad displays any zones that
tripped or any transmission problems that occurred during the
armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.
Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.
Disarming an All/Perimeter System
1. During the entry delay time, the keypad displays ENTER
CODE:. Enter your user code.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your user
code. The keypad displays DISARM SILENCE.
2. Press the SELECT key under DISARM to disarm the system and
silence the alarm.
The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
3. Press the SELECT key under SILENCE to stop the bell or siren
but NOT disarm the system.
If you do not press any SELECT key, or you press the COMMAND
key, the system will automatically disarm and silence the alarm.
4. If your system is programmed to send an Abort (alarm cancel)
report to the central station, the keypad displays ALARM
CANCELLED.
Note: If your system is programmed to send an Abort (alarm cancel)
report to the central station, selecting DISARM will send this
report to the central station. Be sure that you want the alarm
message to be cancelled BEFORE deciding to disarm the system.
If you do not want to disarm the system and send the abort report,
press SILENCE to only turn off the alarm bells.
2. The keypad then displays any zones that went into alarm or any
communication problems that occurred during the armed
period.
3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
8
Arming and Disarming
Home/Away System Arming
4. Select AWAY to arm the Perimeter, Interior, and Bedroom.
Area Assignment: Your security system is divided into two or
three separate areas. Motion detectors, inside doors, and other
interior devices are assigned to an Interior and possibly Bedroom
area while windows and exterior doors, are assigned to a
Perimeter area.
5. The keypad displays zones that have been bypassed prior to
arming and 24-hour zones that are in a bad condition. No
action is required by you.
Arming the system: When arming a Home/Away system, the
keypad displays HOME
AWAY or HOME SLEEP AWAY. If you
select AWAY, you arm all areas of the system. You will want to arm
all areas when leaving with nobody staying inside. Selecting HOME
arms only the Perimeter of the system. Perimeter arming is for
when you are staying inside but want the comfort of knowing the
exterior doors and windows are armed. Selecting SLEEP arms the
Perimeter and Interior devices but leaves devices near bedrooms
and other nighttime areas off.
System Ready/System Not Ready Keypad
Displays
When all zones in the system are in a normal condition and can be
armed without bypassing, the keypad displays SYSTEM READY. If
there are one or more zones that are not in a normal condition,
the keypad displays SYSTEM NOT READY. Pressing any top row
SELECT key during this display shows the bad zone name.
Arming a Home/Away System
1. Enter your 4-digit user code. The keypad displays HOME
AWAY or HOME SLEEP AWAY (you may have three areas).
2. Select HOME to arm the Perimeter only.
3. Select SLEEP to arm the Perimeter and Interior.
Arming and Disarming
6. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it
later returns to normal. A zone that is bypassed will remain
bypassed until the system is disarmed. See steps 6a through
6d.
6a. If a problem exists on any zones, the zone name and
problem are shown followed by: OKAY BYPASS STOP.
6b. Select OKAY to force arm the zone(s) before arming.
6c. Select BYPASS to bypass the zone(s) before arming.
6d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
7. The keypad displays PERIMETER ON if you selected HOME, or
PERIM/INT ON if you selected SLEEP, or ALL SYSTEM ON if you
selected AWAY.
8. The keypad next displays EXIT: ## INSTNT and begins to count
down the number of seconds remaining for you to exit. When
the delay expires, all zones are armed.
9. You can select INSTNT while EXIT: ## INSTNT is displayed to
immediately arm all zones and make them instant. The keypad
displays INSTANT.
10. When the system is fully armed, the keypad displays PERIMETER
ON for Perimeter arming, PERIM/INT ON for Perimeter and
Interior arming, and ALL SYSTEM ON for all areas armed.
9
Home/Away System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an
alarm. After opening the door, the keypad sounds a prewarn tone
to remind you to disarm the system. You must disarm the system
before the prewarn tone expires or an alarm on the door zone will
occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter
your code to disarm the system.
Alarm Display: After disarming, the keypad displays any zones that
tripped or any communication problems that occurred during the
armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.
Disarming a Home/Away System
1. During the entry delay, the keypad displays ENTER CODE:.
Enter your 4-digit user code.
2. The keypad then displays any alarms or communication
problems that occurred during the armed period.
3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your 4-digit
user code. The keypad displays DISARM
SILENCE.
2. Press the SELECT key under DISARM to disarm the system and
silence the alarm.
Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.
The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.
3. Press the SELECT key under SILENCE to stop the bell or siren
but NOT disarm the system.
Easy Exit™ Feature
While the system is armed, you can also just press the COMMAND
and then the 9 key to restart the exit delays to allow you to exit
the premises without disarming the system. After the exit delay
time expires, the system rearms automatically. This feature allows
you to get the paper, let your pet out, or leave for work without
having to disarm and then rearm the system.
10
If you do not press any SELECT key, or you press the
COMMAND key, the system will automatically disarm and
silence the alarm.
4. If your system is programmed to send an Abort (alarm cancel)
report to the central station, the keypad displays ALARM
CANCELLED.
Note: If your system is programmed to send an Abort (alarm cancel)
report to the central station, selecting DISARM will send this
report to the central station. Be sure that you want the alarm
message to be cancelled BEFORE deciding to disarm the system.
If you do not want to disarm the system and send the abort report,
press SILENCE to only turn off the alarm bells.
Arming and Disarming
Security Command User Menu
Zone Activity Check
Many of the features of your system have been put into a User
Menu you can access from any Security Command keypad.
User Code Level: Master or Standard
To access the User Menu:
1. Press the COMMAND key until MENU?
NO YES displays.
2. Select YES. The keypad displays ENTER CODE: –. Enter your
user code. You can now scroll down through the list of system
features available to your authority level.
The following pages detail each User Menu item and provide
instructions on when and how to use them properly.
User Check-in
User Code Level: Master or Standard
Function: This feature allows you to monitor the arrival of
latchkey children or employees by having a special Check-in
Report sent to your numeric pager. Your system must be
programmed for the Pager Direct™ option. The Appendix section
of this guide contains Quick Reference cards for your wallet or
purse.
Sending a Check-in Report:
1. After disarming the system, access the User Menu.
(Or press the COMMAND then 7 key and enter your user code
to send a Check-in Report. This feature operates on 32character keypads only.)
2. At the USER CHECKIN? display, press any SELECT key. The
keypad displays USER CHECKIN: 22 ( 22 = user number).
Your security system may be programmed for the Zone Activity
Check feature to monitor a person for non-activity. This could be
used for a person living alone to detect when they have not
tripped a disarmed zone within a programmed period of time. This
feature can be programmed for you at any time.
Function: This option allows you to enable or disable the Zone
Activity Check which monitors your system for zone activity.
When the programmed time period is exceeded because no
activity is detected, your keypads will sound a steady tone and
display PRESS ANY KEY. Pressing any key on the keypad restarts
the no activity programmed time period and prevents your system
from sending a “User Activity Not Detected” report to the
central station.
Note: The Zone Activity Check is disabled when a schedule is
entered to allow for sleeping hours and is automatically enabled
when an area is armed or disarmed.
Selecting Zone Activity Check:
1. At the ACTIVITY CHECK? display, press any SELECT key. The
keypad displays ENABLE? YES NO. The default is YES.
2. When NO is selected, the keypad displays CHECK DISABLED
for four seconds and then sends the Activity Check Disabled
message to the central station.
3. When YES is selected, the keypad displays CHECK ENABLED
for four seconds and then sends the Activity Check Enabled
message to the central station.
3. The panel sends the Check-in Report containing your account
number and user number to the pager.
User Menu
11
Sensor Reset
Outputs On Off
User Code Level: Master or Standard
User Code Level: Master or Standard.
Function: Resets smoke or glassbreak detectors. Also clears Fire
and Supervisory zone alarms and trouble keypad displays. Sensor
Reset also clears low battery displays if your system is using
wireless sensors.
Function: Allows you to turn the system's outputs on and off.
Once smoke or glassbreak detectors have tripped, they must be
reset before they can detect any additional alarm conditions.
When Sensor Reset is selected, power to the detectors is
temporarily removed by the system allowing them to reset.
Make sure all smoke is cleared from around the area of the smoke
detectors before performing a Sensor Reset to prevent the alarm
from occurring again.
Resetting the Sensors
This function is used to individually turn your system’s relay
outputs on and off. Your system may use these outputs to control
interior and exterior lighting, or heating, air conditioning, or
other appliances.
The names and numbers of the outputs on your system are located
in the System Setup section at the back of this guide.
Turning the Outputs On and Off
1. Access the User Menu.
2. Press the COMMAND key until OUTPUTS ON/OFF? displays.
3. Press any one of the SELECT keys.
1. Access the User Menu.
4. The keypad displays OUTPUT: - ON OFF.
2. When SENSOR RESET? is displayed, press any SELECT key. The
keypad displays SENSORS OFF for five seconds followed by
SENSORS ON.
5. Enter the output number you want to turn on or off. The
output number appears in the display.
3. The keypad returns to the status display.
Enter your user code to reset sensors
While your system is disarmed, you can just enter your user code
and press COMMAND to reset the sensors.
This also activates the door strike if your system has an Easy Entry™
access control keypad.
12
6. With the output number displayed, press the SELECT key
under ON or OFF. The output is then turned on or off,
depending on your selection, and remains in that state until
you change it.
7. The system automatically removes the output number and a
new output number can be entered. Refer back to step 5.
To exit the Output menu option, press the ARROW key until you
have returned to the keypad's Status List.
User Menu
Bypass Zones
Zone Monitor
User Code Level: Master or Standard.
User Code Level: Master and Standard.
Function: Allows you to bypass a zone prior to arming the system.
Function: Allows the system to monitor selected disarmed zones
(doors, windows, or motion detectors). When a monitored zone
is tripped, the keypad sounds a tone and displays the zone name.
This is an ideal feature for monitoring doors to tell when someone
comes in or goes out.
Bypassing is usually done when a zone cannot be restored to
normal and you want to arm the system. Once bypassed, the
system will not respond to any activity on the zone.
A zone can be bypassed only while it is disarmed. Since Fire, Panic,
Emergency, and Supervisory zones are always armed, they can
never be bypassed.
The Bypass Zones function can also be used to restore a bypassed
zone back into the system. This can only be done while the zone
is disarmed.
When Bypass Zones is selected, a report of the bypassing can be
sent to your central station. This is optional and can be programmed
for you at any time.
Using the Bypass Zones Function
1. Access the User Menu.
2. Press the COMMAND key until BYPASS ZONES? displays.
3. Press any one of the SELECT keys. The keypad displays ZONE:
- RST BYPS.
4. To reset a zone, enter the zone number and press the SELECT
key under RST.
5. To Bypass a zone, enter the zone number and press the
SELECT key under BYPS.
User Menu
You can place any combination of disarmed zones in Zone Monitor
but only the most recently tripped zone is displayed. The
displayed zone name clears automatically after a short time or
when the zone is armed.
Zone Monitor does not function while the system is armed but a
zone placed into it will still be monitored when the system is
disarmed.
Using Zone Monitor as part of your weekly system test: After
using the System Test function (see page 14), place all perimeter
and interior zones in Zone Monitor. Starting at the front door,open
and then close each door and window in the premises. You should
hear the keypad beep each time. The keypad will also display the
name of each zone as the device is opened.
Once all protected doors and windows have been tested, walk in
front of each motion detector. The keypad should beep to
confirm their operation. If at any time during your weekly testing
a device does not cause the keypad to beep, call the service
department for assistance.
13
Using the Zone Monitor Function
System Test
1. Access the User Menu.
User Code Level: Master or Standard.
2. Press the COMMAND key until ZONE MONITOR? displays.
Function: System Test is used to test the battery, alarm bell or
siren, and communication to a central station. The System Test
function begins automatically as soon as you select it.
3. Press any one of the SELECT keys.
The keypad displays PERIM ALL NBR .
4. Select PERIM to place all disarmed perimeter zones into Zone
Monitor.
Using the System Test Function
1. Access the User Menu.
4a. The keypad displays PERIM? ADD RMV.
2. Press the COMMAND key until SYSTEM TEST? displays.
4b. Select ADD to add all perimeter zones to Zone Monitor.
3. Press any one of the SELECT keys. The system test begins
automatically and the keypad displays:
4c. Select RMV to remove all perimeter zones.
5. Select ALL to place all disarmed perimeter and interior zones
into Zone Monitor.
5a. The keypad displays ALL? ADD RMV.
5b. Select ADD to add all disarmed zones to Zone Monitor.
5c. Select RMV to remove all disarmed zones.
1) BELL SOUNDING during a two second bell test, then:
2) BATTERY - OKAY or BATTERY - TRBL to indicate the
condition of the battery, then:
* 3) TRANSMIT TEST and ATTEMPT NO : 1 during the
transmit test, then:
6. Select NBR to enter a specific zone number for zone monitor.
4) TRANSMIT OKAY or TRANSMIT FAILED to show the
results of the transmit test, then:
7. If NBR is selected, the keypad displays ZONE : - ADD RMV.
5) TEST END to indicate the System Test is complete.
7a. Enter any zone number and select ADD to add this zone.
6) You can end the transmit test by pressing the ARROW key.
7b. Enter any zone number and select RMV to remove the
zone.
* The transmit test does not operate on local systems.
8. The zone number automatically disappears and a new zone
number can then be entered in step 7a.
14
Testing your system's burglary protection: The System Test
function should be part of your weekly testing and should be
followed by placing the interior and perimeter burglary
devices in Zone Monitor mode. This allows you to open and
then close each protected door and window while listening
for the keypad to beep confirming its operation. See Zone
Monitor.
User Menu
User Codes
User Codes
User Code Level: Master only.
User Code Authority Levels
Function: Allows you to add or delete a user from the system or
change their user code or authority level.
There are three characteristics associated with each user code:
10
User number
3812
User Code
Master
Authority level
User Number - Your system supports 16 users. Each user is
numbered from 1 to 16. This number identifies them to the system
and is transmitted to the central station (if your system is monitored)
when they arm or disarm the system.
User Code - Users also have a 4-digit user code they enter into the
keypad when arming or disarming. This user code is kept secret from
other users and is not transmitted to the central station when they
arm or disarm.
Users enter only their own user code when operating the system.
Authority Level - The user is also assigned a level of authority
(Master or Standard) by the person administrating the system that
determines the functions they can access.
The table to the right lists system functions users are allowed to
access based on the authority level assigned to their codes at the
time they are added to the system.
(continued)
System Options
Standard
Master
Sensor Reset
Outputs On/Off
Bypass Zones
Zone Monitor
System Test
Arm and Disarm
Display Events
Date and Time
User Codes
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Adding User codes:
1. Access the User Menu.
2. Press the COMMAND key until USER CODES? displays.
3. Press any SELECT key. The keypad displays ADD DEL CHG.
4. Press the SELECT key under ADD to add a new user code.
(You must have a Master user level to add a user to the system.)
5. At the USER NUMBER:
- prompt, enter a user number and
press COMMAND. The displays changes to CODE NO: .
6. Enter a 4-digit user code and press COMMAND. This is the
number the user will use each time they arm, disarm, or make
changes to the system.
Note: If your system is using an access control reader, present the
new user's access device instead of entering a user code.
User Menu
15
User Codes
(continued)
7. The display changes to MASTER? NO YES. Select YES to make
this a Master user level with the authority to access all User
Menu functions.
Select NO to make this a Standard user level. The following
options can then be selected:
7a. TEMP CODE NO YES.
Select NO to make this a permanent user code.
Select YES to make this a temporary code that automatically
expires in 7 days. Temporary codes are ideal for guests or
service technicians. You can delete a Temporary user code
at any time before the 7 day active period ends.
7b. ARM ONLY NO YES.
Select NO to allow this user to arm and disarm the system
and access all Standard level functions in the User Menu.
Select YES to restrict this user to arming only.
(The Arm Only user code can bypass zones not in a normal
condition at the time of arming.)
8. After you have completed making your selections, the keypad
display shows USER # ADDED.
9. Press the ARROW key once to add another user or twice to exit
the User Menu.
16
Deleting User codes:
1. Access the User Menu.
2. Press the COMMAND key until USER CODES? displays.
3. Press any one of the SELECT keys. The keypad displays ADD DEL
CHG.
4. Press the SELECT key under DEL to delete a user code from the
system. You must have a Master user code level to be able to
delete a user code.
5. At the USER NUMBER: - prompt, enter the user number you
want to delete and press COMMAND. The displays changes to
USER # DELETED.
6. The display then changes back to USER NUMBER: - for you
to delete another user. Press the ARROW key twice to exit the
User Menu.
Ambush Codes
Your system may be programmed to allow user number 1 to be an
Ambush code. The Ambush code functions identically to other codes
with the exception that it sends a silent alarm to the central station.
This silent alarm alerts the operator to a duress situation at the
premises and prompts the immediate notification of the authorities.
Refer to the System Setup section of this guide to see if your system
is programmed for Ambush. If so, do NOT program a code for user
number 1 if you intend to use the Ambush function.
User Menu
Changing User codes
1. Access the User Menu.
2. Press the COMMAND key until USER CODES? displays.
Date and Time
User Code Level: Master only.
3. Press any one of the SELECT keys. The keypad displays ADD DEL
CHG.
Function: Allows you to change the current date and time
displayed on the keypad and used by the system for schedules and
Display Events.
4. Press the SELECT key under CHG to change a user code. You
must have a Master user code level to change a user code.
Setting the Date and Time
5. At the USER NUMBER:
- prompt, enter the user number to
change and press COMMAND.
6. The display changes to CODE NO: * * * *. Enter the new 4digit user code and press COMMAND. If the code you entered is
already in use, or is a code used internally by the system, the
keypad displays ALREADY IN USE. You must enter a different
4-digit user code.
7. If you are changing a code other than your own, the keypad next
displays MASTER? NO YES. Select YES if you want this user to
have a Master authority level.
1. Access the User Menu.
2. Press COMMAND until TIME? displays. Press any SELECT key.
3. The keypad displays the current day and time. Press the
COMMAND key. The keypad displays the current date. Press the
COMMAND key to make any changes.
4. The keypad displays TIME DAY DATE.
5. Press the SELECT key under TIME to change the time. The
keypad displays – : AM PM. Enter the current time and select
AM or PM.
The display changes back to TIME DAY DATE.
Select NO if you want this user to have a Standard authority
level. If you select NO, refer to item number 7 in the Adding
User Codes section on the previous page.
6. Press the SELECT key under DAY to change the day of the week.
The keypad displays SUN MON TUE WED. If the current day is
not displayed, press the COMMAND key. Press the SELECT key
under the correct day.
Important: Changing a user code does not change the user number.
User number two may have their user code changed from 1234 to
5678 but they are still user number two.
7. Press the SELECT key under DATE to change the date. The
keypad displays:
MONTH: - Enter one or two digits for the month. Press COMMAND.
DAY: - Enter up to two digits for the day. Press COMMAND.
YEAR: - Enter up to two digits for the year. Press COMMAND.
The display returns to TIME DAY DATE. Press the ARROW key to
exit the User Menu.
User Menu
17
Display Events
Zone Activity Check Event Display
User Code Level: Master or Standard.
This displays the date and time the Zone Activity Check was enabled
or disabled.
Function: Allows you to review up to 60 past events that occurred
on your system from any keypad. Once 60 events are stored, any new
event causes the oldest event to be cleared.
SELECT keys
Note: This section shows the User's
Guide Display Events items for both
JONES RESIDENCE
F R I 2 : 51 AM
16-character (single line) and
32-character keypad displays. While
in the Display Events function, use the
1
2
3
4
5
6
8
7
COMMAND and ARROW keys to go
9
0
forward or backward through the list
of events.
COMMAND key
ARROW key
16-Character Display
Description
ACT ENABLED 10/17
The Zone Activity Check was enabled on
October 17.
32-Character Display
Description
POWER
ARMED
AB C
DEF
GHI
MN O
PQR
S TU
JKL
VWX
COMMAND
5:18P 10/17
ACT DISABLED
5:18P 10/17
The Zone Activity Check was disabled
on October 17, at 5:18 pm.
YZ
Activity Check Event Types - There are 3 event types:
ACT DISABLED
ACT ENABLED
NO ZONE ACTIVITY
Using the Display Events Function
1. Access the User Menu.
2. Press the COMMAND key until DISPLAY EVENTS? displays. Press
any SELECT key.
3. The keypad displays FIRST LAST. Select FIRST to view events
starting from the oldest to the newest. Select LAST to view
events starting from the newest to the oldest.
If you select FIRST, use the COMMAND key to scroll up through
the events displays.
If you select LAST, use the ARROW key to scroll down through
the event displays. Zone Event Displays
18
User Menu
Zone Bypass Event Displays
Zone Event Displays
This displays the bypassing of system zones.
This section displays alarms, troubles, and other events that could
occur on your protection zones.
16-Character Display
Description
26 BYPS 1 2 1017
Zone 26 bypassed by user 12. Press the
left Select key for the zone name and
the right Select key for the time.
32-Character Display
Description
BYP 5:18P 10 / 17
EAST W I NDOW
The east window zone was bypassed.
Press a Select key for the zone number
and user number.
16-Character Display
Description
2 BURG ALR 1017
A burglary alarm occurred on zone 2.
Press the right Select key for the time
the alarm occurred.
32-Character Display
Description
A LR 10: 23P 10/17
BAS EM ENT DOOR
An alarm occurred at 10:23 PM on Oct. 17.
Press any Select key to see the zone
number and zone type.
Bypass Event Types - There are 3 event types:
BYP - Bypass
RST - Restore
FRC - Force Arm
Note: You may sometimes see the user as SWG. These are short for
Swinger Bypass which is an automatic function that allows the
system to bypass a zone.This section displays alarms, troubles, and
other events that could occur on your protection zones.
Zone Type - There are 7 possible zone types you may see here.
FIRE - Fire
PANC - Panic
EMRG - Emergency
SUPV - Supervisory
AUX1 - Auxiliary 1
AUX2 - Auxiliary 2
BURG - Burglary
Event Types - There are 7 event type you may see here:
ALR - Alarm
TBL - Trouble
RST - Restore
LOW - Low battery
MIS - Missing xmitter
FLT - Zone Fault
SVC - Service Smoke Detector
Note: LOW and MIS are for wireless systems only.
User Menu
19
Arming and Disarming Event Displays
User Code Change Event Displays
This displays any arming or disarming of system areas.
This displays any addition, deletion, or change to a user code.
16-Character Display
Description
16-Character Display
Description
ARM
Area 3 has been armed by user 12. Press
the left Select key for the area name.
Press the right Select key for the time
the arming occurred.
12
User 12 added user 19 on Oct. 17. Press
the right Select key for the time this
occurred.
3
12
1017
32-Character Display
Description
A RM 5:10P 10/ 17
PERI M ET ER
The Perimeter was armed at 5:10 PM.
Press any Select key to display the area
number and user number.
Arming Event Types - There are 2 event type you may see here:
ARM - User armed the system
DIS - User disarmed the system
User Check-in Event Displays
This shows when a user selected the pager Check-in feature from
the User Menu. See page 11 for more information.
ADD 19 1017
32-Character Display
Description
A DD 11: 41A 10 / 17
US:19 BY US:12
User 19 added by user 12 at 11:41
AM.
User Code Event Types - There are 3 event type you may see here:
ADD - User added
DEL - User deleted
CHG - User code or authority level has been changed.
Supervisory Event Displays
This displays the date and time of an automatic test report.
16-Character Display
Description
16-Character Display
Description
AUTO RECALL 1017
The test report was sent on Oct. 17.
CHECKIN 16 1017
User 16 selected the Check-in feature on
Oct. 17. Press the right Select key for
the Checkin time.
32-Character Display
Description
32-Character Display
Description
MSG 11: 58P 10 / 17
AUTO RECALL
The test report was sent to the central
station at the date and time shown.
MSG 3: 31P 10 / 17
CHECKIN USER: 16
User 16 selected the Check-in feature
at 3:31 PM on Oct.17.
20
User Menu
System Monitor Event Displays
Service Request?
This displays any loss of the system's AC power or battery.
User Code Level: Master only
16-Character Display
Description
POWER T BL 1017
An AC failure occurred on the system.
Press the right Select key for the time.
32-Character Display
Description
TBL 1: 05A 10 / 17
A C POW ER
An AC failure occurred at 1:05
AM.
System Monitor Event Types - There are 2 event types:
TBL - Trouble
RST - Restore
System Monitor Event Names - There are 2 system monitors:
AC POWER
User Menu
BATTERY
Function: Allows you to send a Request for Service message to the
central station when there is a problem on your system.
After the Display Events function in the keypad User Menu, you will
see the SERVICE REQUEST? display if it has been programmed for
your user code. If this feature has been programmed, and you would
like to send a Request for Service report to the central station, press
any top row SELECT key while SERVICE REQUEST? is displayed. After
the Request for Service report is sent, the keypad displays REQUEST
MADE for four seconds.
If there is a problem with the telephone line connected to the
system, you must contact our service department directly for
assistance.
Note: This feature is not displayed if it has not been enabled on your
system.
21
System Setup
Protection Areas
We have provided this System Setup section to allow you to track the
current status of the programmable options on your Security
Command system. If you make changes to the system, you should
update the information contained on these pages.
Number
My system is monitored by a central
station.
❏ Yes
❏ No
Description
1
_______________________________________________
2
_______________________________________________
3
_______________________________________________
4
_______________________________________________
C/S Name:
Address:
Outputs
City/State:
Your system has 4 outputs that can be used for various functions.
Below is a list of these outputs and the devices they control.
Emergency Phone:
Output #
Service Phone:
Service Manager:
My system sends Opening and Closing
reports.
❏ Yes
❏ No
My system sends Zone Bypass reports.
❏ Yes
❏ No
What it controls
1
_______________________________________________
2
_______________________________________________
3
_______________________________________________
4
_______________________________________________
Enter the Output number above when using the Outputs On Off User
Menu option to manually toggle the outputs.
My system sends Ambush reports.
❏ Yes
22
❏ No
User Menu
User Codes
Your system provides 16 user codes you can program for individual users. As you add new users or change current users' codes, you can keep
track of their name, user number, and other information here in this section. Use a pencil to allow for changes.
User
User Name
Level Temp Code Arm Only
HOW TO FILL IN THIS
TABLE
1
M S
Y N
Y N
2
M S
Y N
Y N
3
M S
Y N
Y N
User - The User Number of the person
authorized to use the system.
4
M S
Y N
Y N
Level - Master or Standard authority.
5
M S
Y N
Y N
6
M S
Y N
Y N
Temp Code - Is this code set to expire
after seven days?
7
M S
Y N
Y N
8
M S
Y N
Y N
9
M S
Y N
Y N
10
M S
Y N
Y N
11
M S
Y N
Y N
12
M S
Y N
Y N
13
M S
Y N
Y N
14
M S
Y N
Y N
15
M S
Y N
Y N
16
M S
Y N
Y N
System Setup
Arm Only - Is this user restricted to
just arming?
Refer to the User Codes section of this
User's Guide for additional information.
Circle Your Selections
23
Easy Entry™ User's Guide
This section of the user's guide provides information on using the Easy Entry™ access control capability of the security command system. If
your system is not currently using any access control devices, disregard this section. Easy Entry™ is built into every Security Command system
and can be accessed using Easy Entry™ keypads.
There are three different operating modes: Door Strike, Arming and Disarming, and Entry Delay. All of the examples below assume that your
system requires a user code to arm and disarm the protection.
DOOR STRIKE
All/Perimeter Door Strike - From the Status List, present your card
to the reader. Once it is validated by the system, the Door Strike
relay activates. See Door Strike Relay Operation above. Home/
Away systems only activate the Door Strike relay when arming and
disarming.
24
ABC SECURITY
FRI
2: 5 1 A M
POWER
While the keypad is in
the Status List, present
your access card.
The relay activates for
five seconds during which
you must open the door.
Once you open the door,
you have 40 seconds to
exit and close the door
before the zone 2 SoftShunt expires.
Appendix
ARMING AND DISARMING AN ALL/PERIMETER
SYSTEM
PERIM
Press Command. The keypad displays PERIM ALL (when arming) or DISARM?. Press
the Select key under the option. The keypad displays ENTER CODE: -.
ALL
The system arms or
disarms the areas
and activates the
Door Strike relay.
or
DISARM?
POWER
Present your card to the reader. Once it is validated by the system, both areas
arm or disarm automatically and the Door Strike relay activates.
ARMING AND DISARMING A HOME/AWAY SYSTEM
ABC SECURITY
FRI
2: 5 1 A M
Home/Away system Arming and Disarming - Present your card to the reader. If the system
is armed, once the card is validated all areas are disarmed.
POWER
If the system is disarmed when you present your card, once it is validated all areas are armed
in the AWAY mode.
ENTRY DELAY
ABC SECURITY
ENTER CODE: -
All Systems - Once the protected door is opened and the entry delay
starts, the keypad displays ENTER CODE: -. Present your card to the
reader and, once it is validated, the system disarms all areas accessible
by you and activates the Door Strike relay. See Arming and Disarming.
Using the access reader for user menu access
You can also use a card reader to access the User Menu when the MENU?
NO YES display is shown.
Appendix
POWER
POWER
Access door is
opened.
The system disarms the areas and activates the Door
Strike relay. See Arming and Disarming.
25
FA113 User's Guide
These instructions guide you through the operation of the XRSuper6 Command Processor system using the FA113 Wireless Keychain Remote.
The FA113 uses the audible output capability of the Security Command keypad to sound confirmation tones. It is recommended that you
use the FA113 within hearing distance of these keypads.
Arming a Home/Away or All/Perimeter System
1. Press the ON button once to arm the Perimeter burglary protection. The Security Command keypads emit a single beep to confirm the
arming. The Perimeter arms and all non-priority zones not in a normal condition are force armed.
2. After the single beep, press the ON button a second time to arm the Interior burglary protection. The Security Command keypads emit
two beeps to confirm the arming.
3. After the two beeps, pressing the ON button in Home/Sleep/Away systems arms the Bedrooms burglary protection. The Security Command
keypads emit three beeps to confirm the arming.
Disarming a Home/Away or All/Perimeter System
1. Press the OFF button once. The Security Command keypads emit a single 2-second beep to confirm the disarming.
Using the ALERT Buttons
Pressing the two ALERT buttons simultaneously sends a Panic alarm to the panel. If your system is monitored by a central station, the proper
authorities will be notified of the alarm.
26
Appendix
Pager Direct™ User's Guide
Pager Direct uses the reporting capability of your security system to dial your pager number and send reports in much the same way as someone
sending you a pager message would do. You can receive reports of alarms, troubles, or armings and disarmings of the system and know at
a glance the status of your system.
Area Names
List your system's area names and numbers below:
Area
Name
Area
Name
1 _______________________ 3 ______________________
2 _______________________ 4 ______________________
Service Department Phone: ______________________
Emergency Phone: _____________________________
Central Station Phone: ____________________________
Fold
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Pager Direct™
○
○
○
○
○
Fold
Security Command Numeric Paging
Cut along dotted lines
Appendix
27
Numeric Pager Display
00128-301 2340010
Account Message Always
Area Always User
Number
ID
Zero Number Zero Number
Account Number
This number has been programmed into your Security Command
system as an identifier. Whenever the system sends a message
to your pager, it will always send the account number first to
identify itself.
Message ID
This is always a single digit, 1 to 7, that describes the
message sent.
1 = Zone Alarm
5 = Late To Close
2 = Zone Trouble
6 = User Check-in
3 = Area(s) Arming
7 = Local Message
4 = Area(s) Disarming
Zone or Area Number
If this message is for a zone, the 1- to 2-digit zone number is
displayed. If this message is for areas that are being armed or
disarmed, the area numbers are shown in sequential order. For
example, 1 2 4.
User Number
This is a 3-digit number, that identifies the user.
Security Command Numeric Paging
28
Appendix
PhoneAccess™ User's Guide
This exciting feature allows you to call your XRSuper6 system from any outside touchtone phone to arm and disarm protection areas or
turn on or off the panel's relay outputs.
Quick Reference Wallet Card
How it works
1. Call the XRSuper6 system's phone number from a touch-tone phone.
2. The XRSuper6 answers the call and sounds a short ready tone. You
now have 8 seconds to enter a valid Master user code. If the user
code is accepted by the panel, you will hear one or more beeps
giving you the current armed status of the system. (You can also find
out the armed status of the system by pressing the * key at any time.)
If
All areas are armed
Area 1 (Perimeter) is armed
Any area is armed
All areas are disarmed
You will hear
3 short beeps
1 short beep
2 short beeps
1 long beep
If the user code is not accepted by the panel, you will hear four short
beeps. Check the user code and try again. After 3 unsuccessful
attempts to enter the code, the panel locks out PhoneAccess™ until
a valid user code is entered at a keypad on the XRSuper6 system.
3. Once the user code is accepted by the panel and the armed status
is given, you can enter the following commands:
Press
For this action
You will hear
#, 1
Arm all
3 short beeps
#, 2
Arm Perimeter
1 short beep
#, 3
Arm Perimeter/Interior
2 short beeps
#, 0
Disarm all areas*
1 long beep
#, 5, 4, 0, n* Toggles the output
1 short beep = on
1 long beep = off
(* Use outputs 1, 2, 3, or 4 in place of n)
4 short beeps = restricted
Note: Faulted zones force arm when the area arms.
Appendix
PhoneAccess™ Quick Commands
Press
# then 1
# then 2
# then 3
To do this
Arm all areas
Arm area 1
Arm areas 1 & 2
You will hear
3 short beeps
1 short beep
2 short beeps
Note: Zones in a bad condition are force armed when the area arms.
# then 0
Disarm all areas
1 long beep
#, 5, 4, 0, n*
Toggles the output 1 short beep = on
(* Use outputs 1, 2, 3, or 4 in place of n) 1 long beep = off
(Enter output descriptions below)
4 short beeps = restricted
1. _________________________ 3. _________________________
2. _________________________ 4. _________________________
PhoneAccess™ Quick Commands
Press
# then 1
# then 2
# then 3
To do this
Arm all areas
Arm area 1
Arm areas 1 & 2
You will hear
3 short beeps
1 short beep
2 short beeps
Note: Zones in a bad condition are force armed when the area arms.
# then 0
Disarm all areas
1
#, 5, 4, 0, n*
Toggles the output 1
(* Use outputs 1, 2, 3, or 4 in place of n) 1
(Enter output descriptions below)
4
long beep
short beep = on
long beep = off
short beeps = restricted
1. _________________________ 3. _________________________
2. _________________________ 4. _________________________
Cut along dotted lines
29
1. Call the panel phone number. The panel answers and sounds one
short tone.
2. Enter your code within 8 seconds. One beep means the code is
good. Four short beeps means enter it again. You have 3 tries.
3. You have 30 seconds to enter the first command (see other side)
and 30 seconds for each additional command.
If
All areas are armed
Area 1 (Perim) is armed
Any area is armed
All areas are disarmed
You will hear
3 short beeps
1 short beep
2 short beeps
1 long beep
1. Call the panel phone number. The panel answers and sounds one
short tone.
2. Enter your code within 8 seconds. One beep means the code is
good. Four short beeps means enter it again. You have 3 tries.
3. You have 30 seconds to enter the first command (see other side)
and 30 seconds for each additional command.
If
All areas are armed
Area 1 (Perim) is armed
Any area is armed
All areas are disarmed
30
895 Voice Module
You can also use the 895 Voice Module with the XRSuper6
Command Processor™ panel. The 895 allows you to call your
security system using a touch-tone telephone, and perform a
variety of functions, ranging from arming and disarming to changing
user codes. The 895 operates much like a voice mail system,
providing you with easy to follow English language prompts.
The 895 Voice Module provides you with easy-to-understand
prompts that lead you through the steps to control your security
system. Using your present User Code and User Code Level, you
will have access to the same options of your system using the 895
as you would when using a keypad to control your security system.
The 895 Voice Module easily mounts into the enclosure presently
housing your XRSuper6 Command Processor™ panel. The standard
three-hole configuration allows for easy and quick installation.
For more information about the 895 Voice Module, refer to LT-0421,
the 895 Voice Module User's Guide.
You will hear
3 short beeps
1 short beep
2 short beeps
1 long beep
Appendix
This page has been intentionally left blank.
LT-0622 (10/01)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement