Rhodeus User Manual - Diamond Systems Corporation

GF
Rhodeus
Low Power AMD Geode™ LX800 PC/104 CPU Module with CRT/LCD, LAN and CF
User’s Manual
Copyright  2008
Diamond Systems Corporation
1255 Terra Bella Ave.
Mountain View, CA 94043
Tel (650) 810-2500
www.diamondsystems.com
Index
Table of Contents
Chapter 1 - Introduction ....................................................1
1.1 Copyright Notice .............................................................2
1.2 About User’s Manual .....................................................2
1.3 Warning .............................................................................2
1.4 Replacing the lithium battery ......................................3
1.5 Technical Support ..........................................................3
1.6 Warranty............................................................................4
1.7 Packing List .....................................................................5
1.8 Ordering Information .....................................................5
6SHFL¿FDWLRQ ....................................................................6
1.10 Board Dimensions........................................................7
Chapter 2 - Installation ......................................................9
2.1 Block Diagrams ............................................................ 10
2.2 Jumpers and Connectors ........................................... 11
KBM1: Keyboard & Mouse Connector ..................13
LAN1: Fast Ethernet Connector.............................13
IDE1: 44 pin IDE Connector....................................14
PWR1: Power Supply Connector...........................14
PC/104: PC/104 ISA Interface .................................15
JRS1: COM 2 RS-232/422/485 Select.....................16
LLED1: LAN LED Indicators...................................16
JFRT1: Switches and Indicators............................16
IR1: Intrared Connector ..........................................17
VGA1: CRT Connector............................................17
USB1: USB Connector............................................17
FDD1: 20 pins FDD Connector...............................18
JBAT1: CMOS Setup ...............................................18
LPT1: 20 pins Parallel Port Connector..................19
CON1: RS-422/ 485 Output Connector ..................19
LCD1: TTL LCD Connector.....................................20
-i-
Index
COM1/ COM2: Serial Port Connector ....................20
CFD1: CompactFlash II Socket ..............................21
2.3 The Installation Paths of CD Driver ......................... 22
Chapter 3 - BIOS ................................................................23
3.1 BIOS Introduction ........................................................ 24
3.2 BIOS Setup .................................................................... 24
3.3 Standard CMOS Features .......................................... 25
3.4 Advanced BIOS Features........................................... 28
3.5 Advanced Chipset Features ...................................... 30
3.6 Integrated Peripherals ................................................ 32
3133&,&RQ¿JXUDWLRQV ............................................. 39
3.8 PC Health Status .......................................................... 41
3.9 Load Optimized Defaults .......................................... 42
3.10 Set Password ............................................................ 43
3.11 Save & Exit Setup ...................................................... 44
3.12 Exit Without Saving .................................................. 45
3.13 BIOS Beep Sound code list..................................... 46
3.14 BIOS memory mapping ............................................ 46
3.15 Award BIOS POST Codes ........................................ 47
Chapter 4 - Appendix .......................................................51
4.1 I/O Port Address Map.................................................. 52
4.2 Interrupt Request Lines (IRQ)................................... 53
4.3 DMA Map........................................................................ 53
4.4 Memory Address Map ................................................. 54
4.5 LCD Data Cable Pin Assignment Example........... 55
- ii -
Introduction
1
Chapter 1
Introduction
Chapter 1 - Introduction
-1-
Introduction
1.1 Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct,
indirect, special, incidental, or consequential damages arising from the
use or inability to use the product or documentation, even if advised of the
possibility of such damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
1.2 About User’s Manual
This User’s Manual is intended for experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this User’s Manual, please consult your vendor before further
handling.
1.3 Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow
the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came
with the Single Board Computer, whenever components are separated
from the system.
-2-
Introduction
1.4 Replacing the lithium battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery
type recommended by the manufacturer.
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
1.5 Technical Support
Please do not hesitate to e-mail our support team when you need assistance
www.diamondsystems.com
support@diamondsystems.com
-3-
Introduction
1.6 Warranty
This product is warranted to be in good working order for a period of two
years from the date of purchase. Should this product fail to be in good
working order at any time during this period, we will, at our option, replace
or repair it at no additional charge except as set forth in the following terms.
7KLVZDUUDQW\GRHVQRWDSSO\WRSURGXFWVGDPDJHGE\PLVXVHPRGL¿FDWLRQV
accident or disaster.
9HQGRUDVVXPHVQROLDELOLW\IRUDQ\GDPDJHVORVWSUR¿WVORVWVDYLQJVRUDQ\
other incidental or consequential damage resulting from the use, misuse of,
or inability to use this product. Vendor will not be liable for any claim made
by any other related party.
Vendors disclaim all other warranties, either expressed or implied, including
EXWQRWOLPLWHGWRLPSOLHGZDUUDQWLHVRIPHUFKDQWLELOLW\DQG¿WQHVVIRU
a particular purpose, with respect to the hardware, the accompanying
product’s manual(s) and written materials, and any accompanying hardware.
7KLVOLPLWHGZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWV
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.
-4-
Introduction
1.7 Packing List
1 x Rhodeus Single Board Computer
1 x CD-ROM
1 x Quick Installation Guide
If any of the above items is damaged or missing, contact your vendor
immediately.
1.8 Ordering Information
Rhodeus
Cable Kit
(Optional)
PC/104 CPU module with AMD Geode™ LX800
(500MHz), 1 x SO-DIMM, CRT/LCD & LAN
1 x USB Cable
2 x COM Port Cable
1 x FDD Flat Cable
1 x IDE Cable
1 x Parallel Port Cable
1 x LAN Cable
1 x VGA Cable
1 x KB/MS Cable
-5-
Introduction
6SHFL¿FDWLRQ
Form Factor
PC/104 CPU module
Processor
AMD Geode™ LX800
Cache
64K L1 cache and 128K L2 cache
Chipset
AMD LX800 + CS5536
System Memory
1 x 200 pins DDR SO-DIMM up to 1GB SDRAM
VGA/ LCD Controller
AMD Geode LX series CPU integrated VGA
controller with 2D Engine (Shared memory Max.
64MB)
Ethernet
Realtek 8100CL 10/100 base-T Ethernet
LCD
Supports 18/24-bit TTL up to 1280 x 1024
I/O Chips
W83627HG
BIOS
Phoenix-Award BIOS
IDE Interface
1 x Ultra DMA 33, support 2 IDE devices
Serial Port
2 x RS-232 ports
COM2: RS-232/RS-422/RS-485 selectable
Parallel Port / Floppy
1 x SPP/EPP/ECP mode
1 x Floppy connector
KBMS
Standard PS/2 Keyboard and Mouse
Universal Serial Bus
2 x USB 2.0 ports
PCI to ISA bridge
ITE8888G
Expansion Bus
1 x PC/104 interface
Flash Disk
1 x Type II Compact Flash Disk Socket up to 8GB
Hardware Monitor
Integrated in W83627HG
RTC
AMD Geode CS5536 built-in RTC with lithium
battery
Power Input Connector 1*4 pins power connector
Operation Temp.
-20oC to +70oC or -40oC to +85oC
Watchdog Timer
1 - 255 Level (Sec. or Min.)
Dimension (L x W)
96 x 90 mm (3.8” x 3.5”)
-6-
Introduction
1.10 Board Dimensions
Unit:mm
-7-
Introduction
Unit:mm
-8-
Installation
2
Chapter 2
Installation
Chapter 2 - Installation
-9-
Installation
2.1 Block Diagrams
VGA
LCD
Analog
R.G.B.
TTL 18/24 bit
AMD Geode
LX800 CPU
500MHz
1 x 200pin
SO-DIMM Socket
Memory Bus
PCI to ISA
Bridge
PCI Bus
ISA Bus
PCI LAN
Controller
4 x USB
1 x IDE
PC/104
LAN
RJ-45
USB I/F
IDE ATA I/F
AMD Geode
CS5536
LPC I/F
Super IO
Controller
1 x CF
COM1
LPT1
KB
COM2
FDD
MS
IrDA
- 10 -
Installation
2.2 Jumpers and Connectors
15
CON1
1
LCD1
16
COM2
1
39
2
40
18
COM1
17
9
1
9
1
10
2
10
2
KBM1
1
1
1
2
LAN1
2
1
LPT1
9
44
2
43
14
IDE1
3
19
1
FDD1
20
2
12
1
JBAT1
19
20
1
USB1
13
2
1
2
1
11
9
PC/104
5
PWR1
4
4
B1
A1
B32
A32
1 C0
D0
15
16
C19 6 5
D19
1
2
1
1
VGA1
IR1
JFRT1
LLED1
10
9
8
7
- 11 -
21
JRS1
6
Installation
Jumper / Connector Quick Reference
Jumpers
Label
Function
JRS1
COM2 RS-232/422/485 Select
JBAT1
CMOS Jumper Settings
Connectors
DIMM1
200 pins DDR SDRAM DIMM Socket
PC104_1
PC/104 for ISA Interface
KBM1
PS/2 Keyboard and Mouse
VGA1
CRT Display
LCD1
TTL LCD Panel Connector
COM1 ~ COM2
Serial Ports
CON1
RS-422/485 Output
IR1
Infrared (IR) Connector
LPT1
Parallel Port
LAN1
LAN Ethernet Connector
LLED1
LAN LED Connector
USB1
USB 1/2 Connector
PWR1
Power Connector Small 4P
JFRT1
Front Panel (Switches and Indicators)
FDD1
Floppy Disk Drive Connector
IDE1
Primary IDE Connector
CFD1
Compact Flash Socket
- 12 -
Installation
KBM1: Keyboard & Mouse Connector (1)
Connector type: 2.0mm pitch 1x6 pins wafer connector
Pin
Description
1
KB_DATA
2
GND
3
MS_DATA
4
KB_CLK
5
KB_VCC
6
MS_CLK
1
LAN1: Fast Ethernet Connector (2)
Pin
Description
Pin
Description
1
TX+
2
TX-
3
RX+
4
N/C
5
N/C
6
RX-
7
N/C
8
N/C
9
GND
10
N/C (Key)
Connector type: 2.0mm pitch 2x5 pin header
- 13 -
1
2
9
10
Installation
IDE1: 44 pins IDE Connector (3)
Connector type: 2.0mm pitch 2x22 pin header
Pin
Description
Pin
Description
1
IDE RESET
2
GND
3
DATA7
4
DATA8
5
DATA6
6
DATA9
7
DATA5
8
DATA10
9
DATA4
10
DATA11
11
DATA3
12
DATA12
13
DATA2
14
DATA13
15
DATA1
16
DATA14
17
DATA0
18
DATA15
19
GND
20
N/C (Key)
21
REQ
22
GND
23
IO WRITE
24
GND
25
IO READ
26
GND
27
IO READY
28
IDESEL
29
DACK
30
GND
31
IRQ14
32
N/C
33
ADDR1
34
DIAG
35
ADDR0
36
ADDR2
37
CS#2
38
CS#3
39
IDEACTP
40
GND
41
+5V
42
+5V
43
GND
44
N/C
1
2
3
4
4
PWR1: Power Supply Connector (4)
Pin
Description
1
+5V
2
GND
3
GND
4
+12V
1
Connector type: 2.54mm pitch 1x4 pins wafer one wall connector
- 14 -
Installation
PC/104: PC/104 ISA Interface (5)
1
B
2
3
B
2
3
A
1
A
Pin
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
Description
GND
MEMCS16#
IOCS16#
IRQ10
IRQ11
IRQ12
IRQ15
IRQ14
DACK0#
DREQ0
DACK5#
DREQ5
DACK6#
DREQ6
DACK7#
DREQ7
+5V
MASTER#
GND
GND
0
C
19
C
0
D
19
D
Pin
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
Description
GND
SBHE#
LA23
LA22
LA21
LA20
SA19
SA18
SA17
MEMR#
MEMW#
SD8
SD9
SD10
SD11
SD12
SD13
SD14
SD15
GND
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
Description
IOCHCK#
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
IOCHRDY
AEN
SA19
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
GND
Connector type: PC104 PRESS FIT 2x20P connector
- 15 -
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
Description
GND
RST_DRV
+5V
IRQ9
N/C
DREQ2
N/C
0WS#
+12V
GND
SMEMW#
SMEMR#
IOW#
IOR#
DACK3#
DREQ3
DACK1#
DREQ1
REFRESH#
SYSCLK
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
DACK2#
TC
BALE
+5V
ISA_CLK
GND
GND
Installation
JRS1: COM 2 RS-232/422/485 Select (6)
,WFDQEHFRQ¿JXUHG&20WRRSHUDWHLQ5656RU56PRGH
Connector type: 2.00mm pitch 2x3 pin header.
Select
1-2
3-4
5-6
RS-232 (Default)
ON
OFF
OFF
RS-422
OFF
ON
OFF
RS-485
OFF
OFF
ON
1
2
1
2
1
2
5
6
5
6
5
6
LLED1: LAN LED indicators (7)
Connector type: 2.54mm pitch 1x4 pin header.
Pin
Description
1
LAN1_ACTIVE-
2
LAN1_ACTIVE+
3
LAN1_LINK-
4
LAN1_LINK+
1
JFRT1: Switches and Indicators (8)
It provides connectors for system indicators that provides light indication of
the computer activities and switches to change the computer status.
Connector type: 2.54mm pitch 1x8 pin header.
Pin Description
1
1
RESET+
2
RESET-
3
PWRLED+
4
PWRLED-
5
HDD LED+
6
HDD LED-
7
SPK OUT+
8
SPK OUT-
- 16 -
Installation
IR1: Infrared Connector (9)
Connector Type: 2.54mm pitch 5 pins header
Pin
Voltage
1
+5V
2
N/C
3
IRRX
4
GND
5
IRTX
1
VGA1: CRT Connector (10)
Connector type: 2.0mm pitch 2x5 pin header
Pin
Description
Pin
Description
1
RED
2
GREEN
3
BLUE
4
N/C
5
GND
6
GND
7
GND
8
GND
9
N/C
10
GND
11
N/C (Key)
12
VDDAT
13
HSYNC
14
VSYNC
15
VDCLK
16
N/C
1 2
15 16
USB1: USB Connector (11)
USB1 supports two USB 2.0 w/ 480MB/s by pin header
Pin
Description
Pin
Description
1
+5V
2
+5V
3
USBD-
4
USBD-
5
USBD+
6
USBD+
7
GND
8
GND
9
GND
10
N/C (Key)
Connector type: 2.0mm pitch 2x5 pin header
- 17 -
1
2
9
10
Installation
FDD1: 20 pins FDD Connector (12)
Connector type: 2.0mm pitch 2x10 pin header
Pin
Description
Pin
Description
1
GND
2
Drive density Select 0
3
GND
4
N/C (Key)
5
GND
6
Drive Density Select 1
7
Write Data#
8
Index#
9
Write Gate#
10
Motor Enable A#
11
Track 0#
12
Driver Select B#
13
Write Protect#
14
Driver Select A#
15
Read Data#
16
Motor Enable B#
17
Head Select#
18
Direction#
19
Disk Change#
20
Step#
1
2
19 2
0
JBAT1: CMOS Setup (13)
Connector type: 2.0 mm pitch 1x3 pin header.
Pin
Mode
1-2
Keep CMOS (Default)
1 2 3
2-3
Clear CMOS
1 2 3
Note: After Clear CMOS, please make sure to load default in BIOS
immediately.
- 18 -
Installation
LPT1: 20 pins Parallel Port Connector (14)
Connector type: 2.0mm pitch 2x10 pin header
Pin
Description
Pin
Description
1
STROBE
2
AFD
3
PTD0
4
ERROR
5
PTD1
6
INIT
7
PTD2
8
SLIN
9
PTD3
10
GND
11
PTD4
12
GND
13
PTD5
14
GND (Key)
15
PTD6
16
BUSY
17
PTD7
18
PE
19
ACK
20
SELECT
1
19
CON1: RS-422/ 485 Output Connector (15)
Connector type: 2.0mm pitch 1x4 pins wafer connector
RS-422
RS-485
1
TX+
Data+
2
TX-
Data-
3
RX+
N/C
4
RX-
N/C
1
Pin
- 19 -
1
2
0
2
Installation
LCD1: TTL LCD Connector (16)
Connector type: DF-13-40DP-1.25V
Pin
Description
Pin
Description
2
5V_SAFE
1
5V_SAFE
4
GND
3
GND
6
3V_SAFE
5
3V_SAFE
8
GND
7
N/C
10
PD1
9
PD0
12
PD3
11
PD2
14
PD5
13
PD4
16
PD7
15
PD6
18
PD9
17
PD8
20
PD11
19
PD10
22
PD13
21
PD12
24
PD15
23
PD14
26
PD17
25
PD16
28
PD19
27
PD18
30
PD21
29
PD20
32
PD23
31
PD22
34
GND
33
GND
36
VS
35
SHIFT CLOCK
38
HS
37
DE
40
ENAVDD
39
ENABLK
COM1/ COM2: Serial Port Connector (17), (18)
Pin
Description
Pin
Description
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
10
N/C
Connector type: 2.0mm pitch 2x5 box pin header
- 20 -
1
2
9
10
Installation
CFD1: CompactFlash II Socket
CFD1 does not support hot swap.
'HIDXOWHGE\¿UVW,'(6ODYH
Pin
Description
Pin
Description
1
PDD3
26
GND
2
PDD4
27
PDD11
3
PDD5
28
PDD12
4
PDD6
29
PDD13
5
PDD7
30
PDD14
6
CS#0
31
PDD15
7
GND
32
CS#1
1
6
2
5
2
0
5
8
GND
33
GND
9
GND
34
PDIOR#
10
GND
35
PDIOW#
11
GND
36
+5V
12
GND
37
IRQ14
13
+5V
38
+5V
14
GND
39
CSEL#
15
GND
40
N/C
16
GND
41
IDE_RST#
17
GND
42
PDRDY
18
PDA2
43
PDREQ
19
PDA1
44
PDACK#
20
PDA0
45
IDE_ACT#
21
PDD0
46
CFDIAG
22
PDD1
47
PDD8
23
PDD2
48
PDD9
24
CF_ICS16#
49
PDD10
25
GND
50
GND
- 21 -
Installation
2.3 The Installation Paths of CD Driver
Driver
Path
CHIPSET
\Chiset\AMD\LX
ISA
\ISA\ITE8888
LAN
\Ethernet\REALTEK\8100C
VGA
\Graphics\AMD\LX
- 22 -
BIOS
3
Chapter 3
BIOS
Chapter 3 - BIOS
- 23 -
BIOS
3.1 BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your computer system’s. The BIOS provides for a standard device such as disk drives, serial
ports and parallel ports. It also adds password protection as well as special
VXSSRUWIRUGHWDLOHG¿QHWXQLQJRIWKHFKLSVHWFRQWUROOLQJWKHHQWLUHV\VWHP
3.2 BIOS Setup
The Award BIOS provides a Setup utility program for specifying the system
FRQ¿JXUDWLRQVDQGVHWWLQJV7KH%,26520RIWKHV\VWHPVWRUHVWKH6HWXS
utility.
When you turn on the computer, the Award BIOS is immediately activated.
Pressing the <Del> key immediately allows you to enter the Setup utility.
If you a little bit late press the <Del> key, POST (Power On Self Test) will
continue with its test routines, thus preventing you from invoking the Setup.
If you still wish to enter Setup, restart the system by pressing the ”Reset”
button or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys. You
can also restart by turning the system Off and back On again.
The following message will appear on the screen:
Press <DEL> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to select, the
<PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to
quit. When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup functions
and exit choices.
- 24 -
BIOS
3.3 Standard CMOS Features
“Standard CMOS Features” allows you to record some basic hardware
FRQ¿JXUDWLRQVLQ\RXUFRPSXWHUV\VWHPDQGVHWWKHV\VWHPFORFNDQG
error handling. If the CPU card is already installed in a working system, you
will not need to select this option.
You will need to run the Standard CMOS option, however, if you change
\RXUV\VWHPKDUGZDUHFRQ¿JXUDWLRQVVXFKDVRQERDUGEDWWHU\IDLOVRUWKH
FRQ¿JXUDWLRQVWRUHGLQWKH&026PHPRU\ZDVORVWRUGDPDJHG
Date
The date format is:
Day : Sun to Sat
Month : 1 to 12
Date : 1 to 31
Year : 1999 to 2099
Time
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the date & time, highlight the “Date” & “Time” and use the <PgUp>/
<PgDn> or +/- keys to set the current time.
The time format is:
- 25 -
BIOS
IDE Primary HDDs / IDE Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary channels
for connecting up to four IDE hard disks or other IDE devices.
(DFKFKDQQHOFDQVXSSRUWXSWRWZRKDUGGLVNVWKH¿UVWLVWKH³0DVWHU´DQG
the second is the “Slave”.
3UHVV(QWHU!WRFRQ¿JXUHWKHKDUGGLVN7KHVHOHFWLRQVLQFOXGH$XWR
0DQXDODQG1RQH6HOHFWµ0DQXDO¶WRGH¿QHWKHGULYHLQIRUPDWLRQPDQXDOO\
You will be asked to enter the following items.
Cylinder:
Number of cylinders
Head:
Number of read/write heads
Precomp:
Write precompensation
Landing Zone: Landing zone
Sector:
Number of sectors
The Access Mode selections are as follows:
CHS (HD < 528MB)
LBA
(HD > 528MB and supports Logical Block Addressing)
Large (for MS-DOS only)
Auto
Drive A / Drive B
7KHVH¿HOGVLGHQWLI\WKHW\SHVRIÀRSS\GLVNGULYH$RUGULYH%WKDWKDV
EHHQLQVWDOOHGLQWKHFRPSXWHU7KHDYDLODEOHVSHFL¿FDWLRQVDUH
1.2M, 5.25 in.
None
360K, 5.25 in.
720K, 3.5 in.
1.44M, 3.5 in.
2.88M, 3.5 in.
Video
7KLV¿HOGVHOHFWVWKHW\SHRIYLGHRGLVSOD\FDUGLQVWDOOHGLQ\RXUV\VWHP
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA or PGA monitor
adapters. (default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA adapters.
- 26 -
BIOS
Halt On
7KLV¿HOGGHWHUPLQHVZKHWKHURUQRWWKHV\VWHPZLOOKDOWLIDQHUURULV
detected during power up.
All errors (default)
Whenever the BIOS detects a non-fatal error, the
system will stop and you will be prompted.
The system boot will not be halted for any error that
No errors
may be detected.
All, But Keyboard
The system boot will not be halted for a keyboard
error; it will stop for all other errors.
All, But Diskette
The system boot will not be halted for a disk error; it
will stop for all other errors.
All, But Disk/Key
The system boot will not be halted for a keyboard
or disk error; it will stop for all others.
- 27 -
BIOS
3.4 Advanced BIOS Features
Quick Power On Self Test
:KHQHQDEOHGWKLV¿HOGVSHHGVXSWKH3RZHU2Q6HOI7HVW3267DIWHU
the system is turned on.
If it is set to Enabled, BIOS will skip some items.
Setting: Enabled (Default), Disabled.
First/ Second Boot Device
7KHVH¿HOGVGHWHUPLQHWKHGULYHWKDWWKHV\VWHPVHDUFKHV¿UVWIRUDQ
operating system. The options available include
Setting: Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, ZIP100, USB-FDD,
USB-ZIP, USB-CDROM, USB-HDD, LAN and Disabled.
Boot Other Device
It allows the system to search for an OS from other devices other than the
ones selected in the First/ Second/ Third Boot Device.
Setting: Enabled (Default), Disabled.
- 28 -
BIOS
Boot Up NumLock Status
It allows you to activate the NumLock function after you power up the
system.
Setting: On (Default), Off.
Security Option
It allows you to limit access to the System and Setup.
When you select System, the system prompts for the User Password every
time you boot up.
When you select Setup, the system always boots up and prompts for the
Supervisor Password only when the Setup utility is called up.
Setting: Setup (Default), System.
Cyrix 6x86/MII CPUID
Disable CPU ID instruction if you are using Netware v5.0.
Setting: Enabled (Default), Disabled.
- 29 -
BIOS
3.5 Advanced Chipset Features
CAS Latency Time
It allows CAS latency time in HCLKs as 2 or 2.5. The system board designer
VKRXOGVHWWKHYDOXHVLQWKLV¿HOGGHSHQGLQJRQWKH'5$0LQVWDOOHG'R
QRWFKDQJHWKHYDOXHVLQWKLV¿HOGXQOHVV\RXFKDQJHVSHFL¿FDWLRQVRIWKH
installed DRAM or CPU.
Setting: 2.5 (Default), 2.
Interleave Select
It allows you to Use the Interleave Select option to specify how the cache
memory is interleaved.
Setting: LOI (Default), HOI.
XOR BA0
Setting: Disabled (Default), Enabled.
XOR BA1
Setting: Disabled (Default), Enabled.
- 30 -
BIOS
XOR MB0
Setting: Disabled (Default), Enabled.
XOR Bit Select
Setting: 18 (Default), 19, 20, 21.
Video Memory Size
In order to determine how much memory is allocated to the video graphics
device.
Setting: None, 8M (Default), 16M, 32M, 64M, 128M, 254M.
Output display
In order to specify the display devices the system is connected to.
Setting: Flat Panel, CRT (Default), Panel & CRT.
)ODW3DQHO&RQ¿JXUDWLRQ
,WDOORZV\RXWRRSHQWKH)ODW3DQHO&RQ¿JXUDWLRQPHQX
Memory Hole At 15M-16M
In order to improve performance, certain space in memory can be reserved
for ISA cards. This memory must be mapped into the memory space below
16 MB.
Setting: Disabled (Default), Enabled.
- 31 -
BIOS
3.6 Integrated Peripherals
OnChip IDE Devicev >>>
On-Chip IDE Channel 1
The integrated peripheral controller contains an IDE interface with support
for two IDE channels. Select Enabled to activate each channel separately.
Setting: Disabled, Enabled (Default).
- 32 -
BIOS
IDE Primary Master/Slave PIO
It allows your system HDD controller to run faster.
Rather than having the BIOS issue with a series of commands that
transferring to or from the disk drive, PIO (Programmed Input/Output) allows
the BIOS to communicate with the controller and CPU directly.
When Auto is selected, the BIOS will select the best available mode.
Setting: Auto (Default), Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.
IDE Primary Master/Slave UDMA
It allows your system to improve disk I/O throughput to 33MB/sec with the
Ultra DMA33 feature.
Setting: Disabled, Auto.
IDE DMA Transfer Access
Setting: Disabled, Enabled (Default).
IDE HDD Block Mode
It allows your HDD controller to use the fast block mode to transfer data to
and from your HDD drive.
Setting: Disabled, Enabled (Default).
- 33 -
BIOS
SuperIO Device >>>
Onboard FDC Controller
Select “Enabled” if you wish to use it. Select “Disabled” if you don’t wish to
use it.
Setting: Disabled, Enabled (Default).
Serial/ Onboard Parallel Port
It allows you to select the onboard serial and parallel ports with their
addresses.
Setting:
Serial Port 1
3F8/IRQ4 (Default)
2F8/IRQ3 (Default)
Serial Port 2
Parallel Port
378H/IRQ7 (Default)
UART Mode Select
It determines the UART 2 mode in your computer.
Setting: IrDA, ASKIR, Normal (Default).
RxD, TxD Active
Setting: Hi,Hi , Hi,Lo (Default) , Lo,Hi , Lo,Lo.
IR Transmission Delay
Setting: Disabled, Enabled (Default).
- 34 -
BIOS
UR2 Duplex Mode
Setting: Full, Half (Default).
Use IR Pins
Setting: RxD2,TxD2 , IR-Rx2Tx2 (Default).
Parallel Port Mode
Setting:
SPP (Default)
EPP
ECP
ECP+EPP
Normal
EPP Mode Select
Setting: EPP1.9, EPP1.7 (Default)
ECP Mode Use DMA
Setting: 1, 3 (Default).
- 35 -
BIOS
IT8888 ISA Decode IO >>>
It allows you to use the IT8888 ISA Decode IO menu to set the IO memory
range for the onboard ISA.
Decode I/O Space 0/ 1/ 2/ 3/ 4/ 5
It allows you to allocate system resources to the ISA bridge and to enable
the function correctly.
Setting: Disabled, Enabled (Default).
Decode I/O Speed 0/ 1/ 2/ 3/ 4/ 5
It allows you to specify the speed of the ISA bus.
Setting: Subtractive Speed, Slow Speed, Medium Speed,
Fast Speed.
- 36 -
BIOS
Decode I/O Address 0/ 1/ 2/ 3/ 4/ 5 [15:4]
It allows you to allocate an address to the ISA bus. The address may range
from 0001 to 0FFF.
Decode I/O Size 0/ 1/ 2/ 3/ 4/ 5
It allows you to specify the size of the ISA bus.
Setting: 1 Byte, 2 Bytes, 4 Bytes, 8 Bytes, 16 Bytes, 32 Bytes, 64 Bytes,
128 Bytes.
IT8888 ISA Decode Memory >>>
It allows you to use the IT8888 ISA Decode Memory to set the resources for
the onboard ISA bus.
Decode Memory Space 0/ 1/ 2/ 3
It allows you to allocate memory resources to the ISA bridge and to enable
the function correctly.
Setting: Disabled (Default), Enabled.
- 37 -
BIOS
Decode Memory Speed 0/ 1/ 2/ 3
It allows you to specify the memory speed of the ISA bus.
Setting: Subtractive Speed, Slow Speed, Medium Speed,
Fast Speed.
Decode Memory Addr. 0/ 1/ 2/ 3 [23:
It allows you to allocate a memory address to the ISA bus. The address may
range from 0001 to 0FFF.
Decode Memory Size 0/ 1/ 2/ 3
It allows you to specify the memory size of the ISA bus.
Setting: 16 KB, 32 KB, 64 KB, 128 KB, 256 KB, 512 KB, 1MB, 2MB.
IT8888 DDMA >>>
Suppose that the ISA bus card is required DMA1 & DMA5.
Set “DDMA1 Support” & “DDMA5 Support” to “Enabled”.
Onboard Lan Boot ROM
Setting: Enabled, Disabled (Default).
- 38 -
BIOS
3133&,&RQ¿JXUDWLRQV
PNP OS Installed
It allows you to enable the PNP OS Install option if it is supported by the OS
installed.
Setting: No (Default), Yes.
5HVHW&RQ¿JXUDWLRQ'DWD
,WDOORZV\RXWRGHWHUPLQHZKHWKHUWRUHVHWWKHFRQ¿JXUDWLRQGDWDRUQRW
Setting: Disabled (Default), Enabled.
Resources Controlled By
7KLV3Q3%,26FDQFRQ¿JXUHDOORIWKHERRWDQGFRPSDWLEOHGHYLFHVZLWKWKH
use of a PnP operating system.
Setting: Auto(ESCD) (Default), Manual.
- 39 -
BIOS
IRQ Resources
,WDOORZV\RXWRFRQ¿JXUHWKH,54'0$5HVRXUFHV
Memory Resources
,WDOORZV\RXWRFRQ¿JXUHWKH0HPRU\5HVRXUFHV
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
It allows you to set whether or not MPEG ISA/VESA VGA cards can
display with PCI/VGA.
When “Enabled”, a PCI/VGA can display with an MPEG ISA/VESA
VGA card.
When “Disabled”, a PCI/VGA can not display with an MPEG ISA/VESA
VGA card.
Setting: Disabled (Default), Enabled.
- 40 -
BIOS
3.8 PC Health Status
Current CPU Temperature
CPU/ MEM VCore
VCC3/ +5V/ +12V/ VBAT(V)/ 5VSB
- 41 -
BIOS
3.9 Load Optimized Defaults
,WDOORZV\RXWRORDGWKHGHIDXOWYDOXHVWR\RXUV\VWHPFRQ¿JXUDWLRQ7KH
default setting is optimal and enabled all high performance features.
- 42 -
BIOS
3.10 Set Password
Using Password to set a password that will be used exclusively on the
system. To specify a password, highlight the type you want and press
<Enter>.
The Enter Password: message prompts on the screen. Type the password,
XSWRHLJKWFKDUDFWHUVLQOHQJWKDQGSUHVV(QWHU!$QGWKHV\VWHPFRQ¿UPV
your password by asking you to type it again. After setting a password, the
screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are prompted
WRHQWHUWKHSDVVZRUG$PHVVDJHZLOOFRQ¿UPWKHSDVVZRUGWREHGLVDEOHG
Once the password is disabled, the system will boot, then you can enter
BIOS Setup freely.
- 43 -
BIOS
3.11 Save & Exit Setup
Typing “Y”, you will quit the setup utility and save all the changes into the
CMOS memory.
Typing “N”, you will return to Setup utility.
- 44 -
BIOS
3.12 Exit Without Saving
7\SLQJ³<´ZLOOTXLWWKH6HWXSXWLOLW\ZLWKRXWVDYLQJWKHPRGL¿FDWLRQV
Typing “N” will return you to Setup utility.
- 45 -
BIOS
3.13 BIOS Beep Sound code list
Beep Sound
Message
1 short (Beep)
System booting is normally
2 short (Beep)
CMOS setting error
1 long - 1 short (Beep)
DRAM error
1 long - 2 short (Beep)
Display card or monitor connected error
1 long - 3 short (Beep)
Keyboard error
1 long - 9 short (Beep)
ROM error
Long (Beep) continuous
DRAM hasn’t inset correctly
Short (Beep) continuous
POWER supply has problem
3.14 BIOS memory mapping
Address
Device Description
E000:0000h - F000:FFFFh
System BIOS Area
D000:2000h - D000:FFFFh
Free space
D000:0000h - D000:1FFFh
LAN ROM
C000:E000h - CF00:FFFFh
Free space
C000:0000h - C000:DFFFh
VGA BIOS
A000:0000h - B000:FFFFh
VGA RAM
0000:0000h - 9000:FFFFh
DOS 640K
- 46 -
BIOS
3.15 Award BIOS POST Codes
CFh Test CMOS read/write functionality
chipset initialization: Disable shadow RAM, L2 cache (socket 7
C0h Early
and below), program basic chipset registers
memory: Auto detection of DRAM size, type and ECC, auto
C1h Detect
detection of L2 cache (socket 7 and below)
C3h Expand compressed BIOS code to DRAM
C5h Call chipset hook to copy BIOS back to E000 & F000 shadow RAM
01h Expand the Xgroup codes located in physical memory address 1000:0
02h Reserved
03h Initial Superio_Early_Init switch
04h Reserved
05h %ODQNRXWVFUHHQ&OHDU&026HUURUÀDJ
06h Reserved
07h Clear 8042 interface; Initialize 8042 self test
Test special keyboard controller for Winbond 977 series Super I/O
08h chips; Enable keyboard interface
09h Reserved
Disable PS/2 mouse interface (optional); Auto detect ports for
0Ah keyboard & mouse followed by a port & interface swap (optional);
Reset keyboard for Winbond 977 series Super I/O chips
0Bh Reserved
0Ch Reserved
0Dh Reserved
F000h segment shadow to see whether it is read/write capable or
0Eh Test
not. If test fails, keep beeping the speaker
0Fh Reserved
10h $XWRGHWHFWÀDVKW\SHWRORDGDSSURSULDWHÀDVKUHDGZULWHFRGHVLQWR
the run time area in F000 for ESCD & DMI support
11h Reserved
walking 1’s algorithm to check out interface in CMOS circuitry.
12h Use
Also set real time clock power status and then check for override
13h Reserved
chipset default values into chipset. Chipset default values
14h Program
are MODBINable by OEM customers
15h Reserved
16h Initial Early_Init_Onboard_Generator switch
17h Reserved
CPU information including brand, SMI type (Cyrix or Intel) and
18h Detect
CPU level (586 or 686)
19h Reserved
1Ah Reserved
Initial interrupts vector table. ,IQRVSHFLDOVSHFL¿HGDOO+:
1Bh interrupts are directed to SPURIOUS_INT_HDLR & S/W interrupts to
SPURIOUS_soft_HDLR
1Ch Reserved
1Dh Initial EARLY_PM_INIT switch
1Eh Reserved
1Fh Load keyboard matrix (notebook platform)
- 47 -
BIOS
20h
21h
22h
23h
24h
25h
26h
27h
28h
29h
2Ah
2Bh
2Ch
2Dh
2Eh
2Fh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
3Dh
3Eh
3Fh
40h
41h
42h
43h
44h
45h
46h
Reserved
HPM initialization (notebook platform)
Reserved
Check validity of RTC value; Load CMOS settings into BIOS
stack. If CMOS checksum fails, use default value instead; Prepare
BIOS resource map for PCI & PnP use. If ESCD is valid, take into
consideration of the ESCD's legacy information; Onboard clock
generator initialization. Disable respective clock resource to empty
PCI & DIMM slots; Early PCI initialization - Enumerate PCI bus
number, assign memory & I/O resource, search for a valid VGA device
& VGA BIOS, and put it into C000:0
Reserved
Reserved
Reserved
Initialize INT 09 buffer
Reserved
Program CPU internal MTRR (P6 & PII) for 0-640K memory address;
Initialize the APIC for Pentium class CPU; Program early chipset
according to CMOS setup; Measure CPU speed; Invoke video BIOS
Reserved
Reserved
Reserved
Initialize multilanguage; Put information on screen display, including
Award title, CPU type, CPU speed, etc...
Reserved
Reserved
Reserved
Reserved
Reserved
Reset keyboard except Winbond 977 series Super I/O chips
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Test 8254
Reserved
Test 8259 interrupt mask bits for channel 1
Reserved
Test 9259 interrupt mask bits for channel 2
Reserved
Reserved
Test 8259 functionality
Reserved
Reserved
Reserved
- 48 -
BIOS
47h
48h
49h
4Ah
4Bh
4Ch
4Dh
4Eh
4Fh
50h
51h
52h
53h
54h
55h
56h
57h
58h
59h
5Ah
5Bh
5Ch
5Dh
5Eh
5Fh
60h
61h
62h
63h
64h
65h
66h
67h
68h
69h
6Ah
6Bh
6Ch
6Dh
6Eh
6Fh
Initialize EISA slot
Reserved
Calculate total memory by testing the last double last word of each
64K page; Program writes allocation for AMD K5 CPU
Reserved
Reserved
Reserved
Reserved
Program MTRR of M1 CPU; initialize L2 cache for P6 class CPU &
program cacheable range; Initialize the APIC for P6 class CPU; On
MP platform, adjust the cacheable range to smaller one in case the
cacheable ranges between each CPU are not identical
Reserved
Initialize USB
Reserved
Test all memory (clear all extended memory to 0)
Reserved
Reserved
Display number of processors (multi-processor platform)
Reserved
Display PnP logo; Early ISA PnP initialization and assign CSN to
every ISA PnP device
Reserved
Initialize the combined Trend Anti-Virus code
Reserved
Show message for entering AWDFLASH.EXE from FDD (optional
feature)
Reserved
Initialize Init_Onboard_Super_IO switch; Initialize Init_Onboard_
AUDIO switch
Reserved
Reserved
Okay to enter Setup utility
Reserved
Reserved
Reserved
Reserved
Initialize PS/2 mouse
Reserved
Prepare memory size information for function call: INT 15h ax=E820h
Reserved
Turn on L2 cache
Reserved
Program chipset registers according to items described in Setup &
$XWR&RQ¿JXUDWLRQWDEOH
Reserved
Assign resources to all ISA PnP devices; Auto assign ports to onboard
COM ports if the corresponding item in Setup is set to “AUTO”
Reserved
,QLWLDOL]HÀRSS\FRQWUROOHU6HWXSÀRSS\UHODWHG¿HOGVLQKDUGZDUH
- 49 -
BIOS
70h
71h
72h
73h
74h
75h
76h
77h
78h
79h
7Ah
7Bh
7Ch
7Dh
7Eh
7Fh
80h
81h
82H
83H
84h
85h
86h
87h
88h
89h
90h
91h
92h
93h
94h
95h
96h
FFh
Reserved
Reserved
Reserved
(QWHU$:')/$6+(;(LI$:')/$6+(;(LVIRXQGLQÀRSS\GLYH
and ALT+F2 is pressed
Reserved
Detect and install all IDE devices: HDD, LS120, ZIP, CDROM...
Reserved
Detect serial ports and parallel ports
Reserved
Reserved
Detect and install coprocessor
Reserved
Reserved
Reserved
Reserved
Switch back to text mode if full screen logo is supported: if errors
occur, report errors & wait for keys, if no errors occur or F1 key is
pressed continue - Clear EPA or customization logo
Reserved
Reserved
Call chipset power management hook: Recover the text fond used
by EPA logo (not for full screen logo), If password is set, ask for
password
Save all data in stack back to CMOS
Initialize ISA PnP boot devices
Final USB initialization; NET PC: Build SYSID structure; Switch
screen back to text mode; Set up ACPI table at top of memory; Invoke
ISA adapter ROM’s; Assign IRQ’s to PCI devices; Initialize APM; Clear
noise of IRQ’s
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Read HDD boot sector information for Trend Anti-Virus code
(QDEOH/FDFKH3URJUDPERRWXSVSHHG&KLSVHW¿QDOLQLWLDOL]DWLRQ
3RZHUPDQDJHPHQW¿QDOLQLWLDOL]DWLRQ&OHDUVFUHHQDQGGLVSOD\
summary table; Program K^ write allocation; Program P6 class write
combining
Program daylight saving; Update keyboard LED and typematic rate
Build MP table; Build and update ESCD; Set CMOS century to 20h or
19h; Load CMOS time into DOS timer tick; Build MSIRQ routing table
Boot attempt (INT 19h)
- 50 -
Appendix
4
Chapter 4
Appendix
Chapter 4 - Appendix
- 51 -
Appendix
4.1 I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port addresses
which also becomes the identity of the device.
The following table lists the I/O port addresses used.
Address
Device Description
00000022 - 0000003F
PCI bus
00000044 - 00000047
PCI bus
0000004C - 0000006F
PCI bus
00000060 - 00000060
PC/AT Enhanced PS/2 Keyboard
00000064 - 00000064
PC/AT Enhanced PS/2 Keyboard
00000072 - 0000007F
PCI bus
00000090 - 00000091
PCI bus
00000093 - 0000009F
PCI bus
000000A2 - 000000BF
PCI bus
000000E0 - 000000EF
PCI bus
00000100 - 00000CF7
PCI bus
00000170 - 00000177
Secondary IDE Channel
000001F0 - 000001F7
Primary IDE Channel
00000274 - 00000277
ISAPNP Read Data Port
00000279 - 00000279
ISAPNP Read Data Port
000002F8 -000002FF
Communications Port
00000376 - 00000376
Secondary IDE Channel
00000378 - 0000037F
Printer Port
000003B0 - 000003BA
Advanced Micro Devices Win 2K/XP Graphics
Driver
000003C0 - 000003DF
Advanced Micro Devices Win 2K/XP Graphics
Driver
000003F0 - 000003F5
Standard Floppy Disk Controller
000003F6 - 000003F6
Primary IDE Channel
000003F7 - 000003F7
Standard Floppy Disk Controller
- 52 -
Appendix
000003F8 - 000003FF
Communications Port
00000778 - 0000077B
Printer Port
00000A79 - 00000A79
ISAPNP Read Data Port
00000D00 - 0000FFFF
PCI Bus
0000FC00 - 0000FCFF
Realtek RTL8139/810x family Fast Ethernet NIC
0000FF00 - 0000FF0F
Standard Dual Channel PCI IDE Controller
4.2 Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the service
required. The following table shows the IRQ used by the devices on board.
Level
Function
IRQ 01
PC/AT Enhanced PS/2 Keyboard
IRQ 03
Communications Port
IRQ 04
Communications Port
IRQ 05
Standard Enhanced PCI to USB Host Controller
IRQ 05
Standard Open HCD USB Host Controller
IRQ 06
Standard Floppy Disk Controller
IRQ 10
Advanced Micro Devices Win 2K/Win Graphics Driver
IRQ 10
Geode LX AES Crypto Driver
IRQ 11
Realtek RTL8139/810x Family Fast Ethernet NIC
IRQ 12
Microsoft PS/2 Mouse
IRQ 14
Primary IDE Channel
4.3 DMA Map
DMA Channel
Device Description
02
Standard Floppy Disk Controller
- 53 -
Appendix
4.4 Memory Address Map
Address
Device Description
EE000000 - EEFFFFFF
Standard Floppy Disk Controller
EFFE8000 - EFFEBFFF
AMD Win 2K/XP Graphics Driver
EFFEC000 - EFFEFFFF
AMD Win 2K/XP Graphics Driver
EFFF0000 - EFFF3FFF
AMD Win 2K/XP Graphics Driver
EFFF4000 - EFFF7FFF
Geode LX AES Crypto Driver
EFFF8000 - EFFFBFFF
AMD Win 2K/XP Graphics Driver
EFFFD000 - EFFFDFFF
Standard Enhanced PCI to USB Host Controller
EFFFE000 - EFFFEFFF
Standard OpenHCD USB Host Controller
EFFFF000 - EFFFF0FF
Realtek RTL8139/810x Family Fast Ethernet
NIC
EFFFF000 - 0009EFFF
PCI Bus
000A0000 - 000BFFFF
PCI Bus
000A0000 - 000BFFFF
AMD Win 2K/XP Graphics Driver
000C8000 - 000EEFFF
PCI Bus
0F7C0000 - FFFEFFFF
PCI Bus
- 54 -
Appendix
4.5 LCD Data Cable Pin Assignment for LG-LB064v02 LCD
LG-LB064V02
Rhodeus SBC
LCD cable pin out
Connector pin out
Pin
Description
Pin
Description
1
GND
3
GND
2
+3.3V
5
3V_SAFE
3
+3.3V
6
3V_SAFE
4
GND
4
GND
5
DCLK
35
SHIFT CLOCK
6
DE
37
DE
7
VSYNC
36
VS
8
HSYNV
38
HS
9
GND
8
GND
10
R0
27
PD18
11
R1
28
PD19
12
R2
29
PD20
13
R3
30
PD21
14
R4
31
PD22
15
R5
32
PD23
16
GND
8
GND
17
G0
19
PD10
18
G1
20
PD11
19
G2
21
PD12
20
G3
22
PD13
21
G4
23
PD14
22
G5
24
PD15
23
GND
33
GND
24
B0
11
PD2
25
B1
12
PD3
26
B2
13
PD4
27
B3
14
PD5
28
B4
15
PD6
29
B5
16
PD7
30
GND
34
GND
- 55 -
Download PDF