PRELIMINARY PRODUCT INFORMATION
MOS INTEGRATED CIRCUIT
mPD78F0058
8-BIT SINGLE-CHIP MICROCONTROLLER
DESCRIPTION
The mPD78F0058 is a product of the mPD780058 Subseries in the 78K/0 Series and equivalent to the
m PD780058 with a flash memory in place of internal ROM. This device is incorporated with a flash memory which
can be programmed without being removed from the substrate.
Functions are described in detail in the following user’s manuals, which should be read when carrying out
design work.
mPD780058, 780058Y Subseries User’s Manual : U12013E
78K/0 Series User’s Manual Instruction
: IEU-1372
FEATURES
• Pin-compatible with mask ROM versions (except VPP pin)
• Flash memory
: 60 KbytesNote 1
• Internal high-speed RAM : 1024 bytes
• Internal expansion RAM : 1024 bytes Note 2
• Buffer RAM
: 32 bytes
• Operable with the same power supply voltage as that of mask ROM version (VDD = 1.8 to 5.5 V)
Notes 1. The flash memory capacity can be changed with the memory size switching register (IMS).
2. The internal expansion RAM capacity can be changed with the internal expansion RAM size
switching register (IXS).
Remark
For the differences between the flash memory versions and the mask ROM versions, refer to
1. DIFFERENCES BETWEEN mPD78F0058 AND MASK ROM VERSIONS.
ORDERING INFORMATION
Part Number
m PD78F0058GC-3B9
Package
80-pin plastic QFP (14 ¥ 14 mm, resin thickness 2.7 mm)
Internal ROM
Flash memory
m PD78F0058GC-8BT Note
80-pin plastic QFP (14 ¥ 14 mm, resin thickness 1.4 mm)
Flash memory
m PD78F0058GK-BE9
80-pin plastic TQFP (fine pitch) (12 ¥ 12 mm)
Flash memory
Note
Under planning
Caution
Two types of packages are available for mPD78F0058GC (refer to 6. PACKAGE DRAWINGS).
For the suppliable package, consult an NEC sales representative.
The information contained in this document is being issued in advance of the production cycle for the
device. The parameters for the device may change before final production or NEC Corporation, at its own
discretion, may withdraw the device prior to its production.
Document No. U12092EJ1V0PM00 (1st edition)
Date Published March 1997 N
Printed in Japan
©
1997
mPD78F0058
78K/0 SERIES DEVELOPMENT
The products in the 78K/0 series are listed below. The names enclosed in boxes are subseries names.
Under mass production
Under development
Y subseries supports I2C bus.
For control
mPD78078Y
Adds timer to mPD78054 with enhanced external interface function
mPD78070AY
ROM-less model of mPD78078
100 pins
mPD78078
100 pins
mPD78070A
100 pins
m PD780018Note m PD780018YNote
80 pins
mPD780058
80 pins
mPD78058F
mPD78058FY
Low EMI noise model of mPD78054
80 pins
mPD78054
mPD78054Y
Adds UART and D/A to m PD78014 with enhanced I/O
Enhanced serial I/O of mPD78078 with limited function
mPD780058YNote Enhanced serial I/O of mPD78054, low EMI noise model
64 pins
mPD780034
mPD780034Y
Enhanced A/D of mPD780024
64 pins
mPD780024
mPD780024Y
Enhanced serial I/O of mPD78018F, low EMI noise model
64 pins
mPD780964
Enhanced A/D of mPD780924
64 pins
mPD780924
Inverter control circuit and UART provided, low EMI noise model
64 pins
mPD78014H
Low EMI noise model of mPD78018F
64 pins
mPD78018F
mPD78018FY
Low-voltage model (1.8 V) of m PD78014 with increased choice of ROM and RAM capacities
64 pins
mPD78014
mPD78014Y
Adds A/D and 16-bit timer to mPD78002
64 pins
mPD780001
64 pins
mPD78002
42/44 pins
mPD78083
Adds A/D to mPD78002
mPD78002Y
Basic subseries for control applications
UART provided, low-voltage (1.8 V) operation
For driving FIPTM
78K/0
series
100 pins
mPD780208
Enhanced l/O, FIP C/D of m PD78044F; Total number of display outputs: 53
80 pins
mPD78044F
Adds 6-bit U/D counter to mPD78024; Total number of display outputs: 34
64 pins
mPD78024
Basic subseries for driving FIP; Total number of display outputs: 26
For driving LCD
100 pins
mPD780308
100 pins
mPD78064B
100 pins
mPD78064
mPD780308Y
Enhanced SIO of m PD78064 with extended ROM and RAM
Low EMI noise model of the mPD78064
mPD78064Y
Subseries for driving LCD with UART provided
Supporting IEBusTM
80 pins
mPD78098
64 pins
m PD78P0914
Adds IEBus controller to mPD78054
For LV
Note
2
Under planning
PWM output, LV digital code decoder, and Hsync counter provided
mPD78F0058
The following lists the main functional differences.
Function
Subseries
For
control
ROM
Capacity
mPD78078
32 K-60 K
mPD78070A
Timer
8-bit 10-bit 8-bit
8-bit 16-bit Watch WDT
4 ch
1 ch
1 ch
1 ch
A/D
A/D
8 ch
–
D/A
2 ch 3 ch (UART: 1 ch)
mPD780058 24 K-60 K
I/O
Value Expansion
88 1.8 V
61 2.7 V
–
mPD780018 48 K-60 K
–
2 ch
2 ch (Time division
3-wire: 1 ch)
88
2 ch 3 ch (Time division
UART: 1 ch)
68 1.8 V
3 ch (UART: 1 ch)
69 2.7 V
mPD78058F 48 K-60 K
mPD78054
VDD MIN. External
Serial Interface
2.0 V
16 K-60 K
–
mPD780034 8 K-32 K
mPD780024
mPD780964
3 ch Note
–
mPD780924
2 ch
mPD78014H
1 ch
8 ch
8 ch
–
–
8 ch
8 ch
–
–
3 ch (UART: 1 ch,
51 1.8 V
Time division 3-wire: 1 ch)
1 ch
2 ch (UART: 2 ch)
47 2.7 V
2ch
53 1.8 V
mPD78018F 8 K-60 K
mPD78014
2.7 V
8 K-32 K
mPD780001 8 K
mPD78002
–
8 K-16 K
mPD78083
For FIP
driving
For LCD
driving
mPD780208 32 K-60 K
2 ch
1 ch
–
1 ch
1 ch
–
–
8 ch
1 ch
1 ch
8 ch
–
–
33 1.8 V
–
2 ch
74 2.7 V
–
68
mPD78024
54
24 K-32 K
mPD78064
16 K-32 K
For IEBus mPD78098
32 K-60 K
Note
1 ch (UART: 1 ch)
mPD78044F 16 K-40 K
mPD780308 48 K-60 K
2 ch
1 ch
1 ch
1 ch
8 ch
mPD78P0914 32 K
–
53
–
–
mPD78064B 32 K
For LV
39
3 ch (Time division 57 2.0 V
UART: 1 ch)
–
2 ch (UART: 1 ch)
2 ch
1 ch
1 ch
1 ch
8 ch
–
6 ch
–
–
1 ch
8 ch
–
2 ch 3 ch (UART: 1 ch)
–
2 ch
69
2.7V
54 4.5 V
10-bit timer: 1 channel
3
mPD78F0058
OVERVIEW OF FUNCTION
Item
Function
Kbytes Note 1
Internal
Flash memory
60
memory
High-speed RAM
1024 bytes
Expansion RAM
1024 bytesNote 2
Buffer RAM
32 bytes
Memory space
64 Kbytes
General-purpose registers
8 bits ¥ 32 registers (8 bits ¥ 8 registers ¥ 4 banks)
Instruction cycle
On-chip instruction execution time cycle modification function
When main system
clock selected
0.4 ms/0.8 ms/1.6 ms/3.2 ms/6.4 ms 12.8 ms (at 5.0-MHz operation)
When subsystem
clock selected
122 ms (at 32.768-kHz operation)
Instruction set
• 16-bit operation
• Multiplication/division (8 bits ¥ 8 bits,16 bits ÷ 8 bits)
• Bit manipulation (set, reset, test, Boolean operation)
• BCD correction, etc.
I/O ports
Total
: 68
• CMOS input
• CMOS I/O
• N-ch open drain I/O
: 2
: 62
: 4
A/D converter
• 8-bit resolution ¥ 8 channels
D/A converter
• 8-bit resolution ¥ 2 channels
Serial interface
• 3-wired serial I/O/SBI/2-wire serial I/O mode selectable
: 1 channel
• 3-wired serial I/O mode (MAX. 32-byte on-chip automatic
transmission/reception function)
: 1 channel
• 3-wired serial I/O/UART mode (on-chip time division transfer function)
Timer
•
•
•
•
Timer output
3 (14-bit PWM output capable: 1)
Clock output
19.5 kHz, 39.1 kHz, 78.1 kHz, 156 kHz, 313 kHz, 625 kHz, 1.25 MHz, 2.5 MHz,
5.0 MHz (main system clock: at 5.0-MHz operation)
32.768 kHz (subsystem clock: at 32.768-kHz operation)
selectable
16-bit timer/event counter
8-bit timer/event counter
Watch timer
Watchdog timer
: 1 channel
:
:
:
:
1
2
1
1
channel
channels
channel
channel
Buzzer output
1.2 kHz, 2.4 kHz, 4.9 kHz, 9.8 kHz (main system clock: at 5.0-MHz operation)
Vectored-interrupt Maskable
Internal : 13, External : 7
source
Non-maskable
Internal : 1
Software
1
Test input
Internal : 1, External : 1
Power supply voltage
VDD = 1.8 to 5.5 V
Operating ambient temperature
TA = –40 to +85°C
Package
• 80-pin plastic QFP (14 ¥ 14 mm, resin thickness 2.7 mm)
• 80-pin plastic QFP (14 ¥ 14 mm, resin thickness 1.4 mm)Note 3
• 80-pin plastic TQFP (fine pitch) (12 ¥ 12 mm)
Notes 1. The flash memory capacity can be changed with the memory size switching register (IMS).
2. The internal expansion RAM capacity can be changed with the internal expansion RAM size
switching register (IXS).
3. Under planning
4
mPD78F0058
PIN CONFIGURATION (Top View)
• 80-pin plastic QFP (14 ¥ 14 mm, resin thickness 2.7 mm)
mPD78F0058GC-3B9
• 80-pin plastic QFP (14 ¥ 14 mm, resin thickness 1.4 mm)
mPD78F0058GC-8BT Note
• 80-pin plastic TQFP (fine pitch) (12 ¥ 12 mm)
P00/INTP0/TI00
P01/INTP1/TI01
P02/INTP2
P03/INTP3
P04/INTP4
P05/INTP5
VSS0
VDD1
X2
VPP
X1
XT2
VDD0
XT1/P07
AVREF0
P10/ANI0
P11/ANI1
P12/ANI2
P13/ANI3
P14/ANI4
mPD78F0058GK-BE9
P15/ANI5
1
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
60
P16/ANI6
2
59
P127/RTP7
P17/ANI7
3
58
P126/RTP6
AVSS
4
57
P125/RTP5
P130/ANO0
5
56
P124/RTP4
P131/ANO1
6
55
P123/RTP3
AVREF1
7
54
P122/RTP2
P70/SI2/RxD0
8
53
P121/RTP1
P71/SO2/TxD0
9
52
P120/RTP0
P72/SCK2/ASCK
10
51
P37
RESET
P20/SI1
11
50
P36/BUZ
P21/SO1
12
49
P35/PCL
P22/SCK1
13
48
P34/TI2
Note
P63
P65/WR
P64/RD
P62
20
41
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
P61
P41/AD1
P60
P66/WAIT
P57/A15
42
P56/A14
19
VSS1
P67/ASTB
P40/AD0
P55/A13
P30/TO0
43
P54/A12
44
18
P53/A11
17
P27/SCK0
P52/A10
P26/SO0/SB1
P51/A9
P31/TO1
P50/A8
45
P47/AD7
16
P46/AD6
P32/TO2
P25/SI0/SB0
P45/AD5
P33/TI1
46
P44/AD4
47
15
P43/AD3
14
P42/AD2
P23/STB/TxD1
P24/BUSY/RxD1
Under planning
Cautions 1. Connect the V PP pin directly to VSS in normal operation mode
2. Connect the AVSS pin to VSS0.
Remark
When the m PD78F0058 is used in application fields that require reduction of the noise generated
from inside the microcontroller, the implementation of noise reduction measures, such as supplying
voltage to VDD0 and VDD1 individually and connecting VSS0 and VSS1 to different ground lines, is
recommended.
5
mPD78F0058
6
A8-A15
: Address Bus
PCL
: Programmable Clock
AD0-AD7
: Address/Data Bus
RD
: Read Strobe
ANI0-ANI7
: Analog Input
RESET
: Reset
ANO0, ANO1 : Analog Output
RTP0-RTP7
: Real-Time Output Port
ASCK
: Asynchronous Serial Clock
RxD0, RxD1
: Receive Data
ASTB
: Address Strobe
SB0, SB1
: Serial Bus
AV REF0, 1
: Analog Reference Voltage
SCK0-SCK2
: Serial Clock
AVSS
: Analog Ground
SI0-SI2
: Serial Input
BUSY
: Busy
SO0-SO2
: Serial Output
BUZ
: Buzzer Clock
STB
: Strobe
INTP0-INTP6 : Interrupt from Peripherals
TI00, TI01
: Timer Input
P00-P05, P07 : Port0
TI1, TI2
: Timer Input
P10-P17
: Port1
TO0-TO2
: Timer Output
P20-P27
: Port2
TxD0, TxD1
: Transmit Data
P30-P37
: Port3
VDD0, VDD1
: Power Supply
P40-P47
: Port4
VPP
: Programming Power Supply
P50-P57
: Port5
VSS0, VSS1
: Ground
P60-P67
: Port6
WAIT
: Wait
P70-P72
: Port7
WR
: Write Strobe
P120-P127
: Port12
X1, X2
: Crystal (Main system Clock)
P130, P131
: Port13
XT1, XT2
: Crystal (Subsystem Clock)
mPD78F0058
BLOCK DIAGRAM
TO0/P30
TI00/INTP0/P00
TI01/INTP1/P01
16-bit TIMER/
EVENT COUNTER
TO1/P31
TI1/P33
8-bit TIMER/
EVENT COUNTER 1
TO2/P32
TI2/P34
8-bit TIMER/
EVENT COUNTER 2
PORT0
P00
P01-P05
P07
PORT1
P10-P17
PORT2
P20-P27
PORT3
P30-P37
PORT4
P40-P47
PORT5
P50-P57
PORT6
P60-P67
PORT7
P70-P72
PORT12
P120-P127
PORT13
P130,P131
REAL-TIME
OUTPUT PORT
RTP0/P120RTP7/P127
WATCHDOG TIMER
WATCH TIMER
SI0/SB0/P25
SO0/SB1/P26
SCK0/P27
SI1/P20
SO1/P21
SCK1/P22
STB/TxD1/P23
BUSY/RxD1/P24
BUSY/RxD1/P24
STB/TxD1/P23
SI2/RxD0/P70
SO2/TxD0/P71
SCK2/ASCK/P72
SERIAL
INTERFACE 0
78K/0
CPU CORE
SERIAL
INTERFACE 1
SERIAL
INTERFACE 2
ANI0/P10ANI7/P17
AVSS
AVREF0
A/D CONVERTER
ANO0/P130,
ANO1/P131
AVSS
AVREF1
D/A CONVERTER
INTP0/P00INTP5/P05
INTERRUPT
CONTROL
BUZ/P36
PCL/P35
FLASH
MEMORY
60 K Bytes
RAM
2048 Bytes
EXTERNAL
ACCESS
AD0/P40AD7/P47
A8/P50A15/P57
RD/P64
WR/P65
WAIT/P66
ASTB/P67
SYSTEM
CONTROL
RESET
X1
X2
XT1/P07
XT2
BUZZER OUTPUT
CLOCK OUTPUT
CONTROL
VDD0,
VDD1
VSS0,
VSS1
VPP
7
mPD78F0058
CONTENTS
1. DIFFERENCES BETWEEN MPD78F0058 AND MASK ROM VERSIONS ......................................
9
2. PIN FUNCTIONS .............................................................................................................................. 10
2.1
Port Pins .................................................................................................................................................. 10
2.2
Non-Port Pins .......................................................................................................................................... 12
2.3
Pin I/O Circuits and Recommended Connection of Unused Pins ...................................................... 14
3. MEMORY SIZE SWITCHING REGISTER (IMS)............................................................................... 18
4. INTERNAL EXPANSION RAM SIZE SWITCHING REGISTER (IXS) .............................................. 19
5. FLASH MEMORY PROGRAMMING ................................................................................................ 20
5.1
Selection of Transmission Method ........................................................................................................ 20
5.2
Function of Flash Memory Programming ............................................................................................. 21
5.3
Connection of Flashpro .......................................................................................................................... 22
6. PACKAGE DRAWINGS ................................................................................................................... 24
APPENDIX A. DEVELOPMENT TOOLS ............................................................................................... 27
APPENDIX B. RELATED DOCUMENTS ............................................................................................... 29
8
mPD78F0058
1. DIFFERENCES BETWEEN mPD78F0058 AND MASK ROM VERSIONS
The m PD78F0058 is a product provided with a flash memory which enables on-board reading, erasing, and
rewriting of programs with device mounted on target system. The functions of the m PD78F0058 (except the
functions specified for flash memory and mask option of P60 to P63 pins) can be made the same as those of the
mask ROM versions by setting the memory size switching register (IMS) and internal expansion RAM size
switching register (IXS).
Table 1-1 shows the differences between the flash memory version (m PD78F0058) and the mask ROM versions
(m PD780053, 780054, 780055, 780056, and 780058).
Table 1-1. Differences between m PD78F0058 and Mask ROM Versions
Item
mPD78F0058
Mask ROM Versions
Internal ROM structure
Flash memory
Mask ROM
Internal ROM capacity
60 Kbytes
mPD780053
mPD780054
mPD780055
mPD780056
mPD780058
:
:
:
:
:
24
32
40
48
60
Internal expansion RAM capacity
1024 bytes
mPD780053
mPD780054
mPD780055
mPD780056
mPD780058
:
:
:
:
:
None
None
None
None
1024 bytes
Internal ROM capacity changeable/not
changeable with memory size switching
register (IMS)
Changeable Note 1
Not changeable
Internal expansion RAM capacity
Changeable Note 2
Not changeable
IC pin
Not provided
Provided
VPP pin
Provided
Not provided
P60 to P63 pin mask option with internal
pull-up resistors
Not provided
Provided
Kbytes
Kbytes
Kbytes
Kbytes
Kbytes
changeable/not changeable with internal
expansion RAM size switching register (IXS)
Notes 1. Flash memory is set to 60 Kbytes by RESET input
2. Internal expansion RAM is set to 1024 bytes by RESET input.
Caution
The noise resistance and noise radiation differ between flash memory versions and mask
ROM versions. When considering the replacement of flash memory versions with mask ROM
versions in the process from trial manufacturing to mass production, adequate evaluation
should be carried out using CS products (not ES products) of mask ROM versions.
Remark
Only the mPD780058 and 78F0058 are provided with IXS.
9
mPD78F0058
2. PIN FUNCTIONS
2.1 Port Pins (1/2)
Pin Name
I/O
P00
Input
P01
I/O
P02
P03
Funciton
After Reset Alternate Function
Port 0
Input only
Input
INTP0/TI00
7-bit input/output port.
Input/output can be specified bit-wise.
When used as an input port, an internal
pull-up resistor can be connected by
software.
Input
INTP1/TI01
INTP2
INTP3
P04
INTP4
P05
INTP5
P07 Note 1
Input
P10-P17
I/O
P20
I/O
P21
P22
P23
Input only
Input
XT1
Port 1
8-bit input/output port.
Input/output can be specified bit-wise.
When used as an input port, an internal pull-up resistor can be
connected by software.Note 2
Input
ANI0-ANI7
Port 2
8-bit input/output port.
Input/output can be specified bit-wise.
When used as an input port, an internal pull-up resistor can be
connected by software.
Input
SI1
SO1
SCK1
STB/TxD1
P24
BUSY/RxD1
P25
SI0/SB0
P26
SO0/SB1
P27
P30
P31
P32
P33
SCK0
I/O
Port 3
8-bit input/output port.
Input/output can be specified bit-wise.
When used as an input port, an internal pull-up resistor can be
connected by software.
Input
TO0
TO1
TO2
TI1
P34
TI2
P35
PCL
P36
BUZ
P37
–
Notes 1. When using P07/XT1 pin as an input port, set 1 to the bit 6 (FRC) of the processor clock control
register. Do not use the feedback resistor of the subsystem clock oscillator.
2. When using P10/ANI0 to P17/ANI7 pins as analog inputs of A/D converter, the internal pull-up
resistor is automatically set unused.
10
mPD78F0058
2.1 Port Pins (2/2)
Pin Name
I/O
Funciton
After Reset Alternate Function
P40-P47
I/O
Port 4
8-bit input/output port.
Input/output can be specified in 8-bit units.
When used as an input port, an internal pull-up resistor can be
connected by software.
Test input flag (KRIF) is set to 1 by the falling edge detection.
Input
AD0-AD7
P50-P57
I/O
Port 5
8-bit input/output port.
LED can be driven directly.
Input/output can be specified bit-wise.
Input
A8-A15
When used as an input port, an internal pull-up resistor can be
connected by software.
P60
I/O
P61
Port 6
8-bit input/output port.
Input/output can be specified bit-wise.
N-ch open drain input/output
port. LED can be driven
directly.
Input
When used as an input port,
an internal pull-up resistor can
be connected by software.
Input
–
P62
P63
P64
P65
RD
WR
P66
WAIT
P67
ASTB
I/O
Port 7
3-bit input/output port.
Input/output can be specified bit-wise.
When used as an input port, an internal pull-up resistor can be
connected by software.
Input
P120-P127 I/O
Port 12
8-bit input/output port.
Input/output can be specified bit-wise.
When used as an input port, an internal pull-up resistor can be
connected by software.
Input
RTP0-RTP7
P130, P131 I/O
Port 13
2-bit input/output port.
Input/output can be specified bit-wise.
When used as an input port, an internal pull-up resistor can be
connected by software.
Input
ANO0, ANO1
P70
P71
P72
SI2/RxD0
SO2/TxD0
SCK2/ASCK
11
mPD78F0058
2.2 Non-Port Pins (1/2)
Pin Name
INTP0
I/O
Input
INTP1
Funciton
External interrupt request input by which the effective edge (rising
edge, falling edge, or both rising edge and falling edge) can be
specified.
After Reset Alternate Function
Input
P00/TI00
P01/TI01
INTP2
P02
INTP3
P03
INTP4
P04
INTP5
SI0
P05
Input
Serial interface serial data input.
Input
SI1
P20
SI2
SO0
P70/RxD
Output
Serial interface serial data output.
Input
SO1
P71/TxD
I/O
Serial interface serial data input/output.
Input
I/O
Serial interface serial clock input/output.
Input
SB1
SCK0
P26/SB1
P21
SO2
SB0
P25/SB0
P25/SI0
P26/SO0
SCK1
P27
P22
SCK2
P72/ASCK
STB
Output
Strobe output for serial interface automatic transmission/reception.
Input
P23/TxD1
BUSY
Input
Busy input for serial interface automatic transmission/reception.
Input
P24/RxD1
RxD0
Input
Serial data input for asynchronous serial interface.
Input
P70/SI2
Output
Serial data output for asynchronous serial interface.
Input
ASCK
Input
Serial clock input for asynchronous serial interface.
Input
P72/SCK2
TI00
Input
External count clock input to 16-bit timer (TM0).
Input
P00/INTP0
RxD1
TxD0
P24/BUSY
TxD1
P71/SO2
P23/STB
TI01
Capture trigger signal input to capture register (CR00).
P01/INTP1
TI1
External count clock input to 8-bit timer (TM1).
P33
TI2
External count clock input to 8-bit timer (TM2).
TO0
Output
16-bit timer output (shared with 14-bit PWM output).
P34
Input
8-bit timer output.
TO1
P30
P31
TO2
P32
PCL
Output
Clock output (for trimming of main system clock and subsystem clock).
Input
P35
BUZ
Output
Buzzer output.
Input
P36
Real-time output port to output data in synchronization with triggers.
Input
P120-P127
RTP0-RTP7 Output
AD0-AD7
I/O
Lower address/data bus for extending memory externally.
Input
P40-P47
A8-A15
Output
Higher address bus for extending memory externally.
Input
P50-P57
RD
Output
Strobe signal output for read operation of external memory.
Input
P64
Strobe signal output for write operation of external memory.
Input
P65
WR
12
mPD78F0058
2.2 Non-Port Pins (2/2)
Pin Name
I/O
WAIT
Input
ASTB
ANI0-ANI7
Input
P66
Output
Strobe output which externally latches address information output to
port 4 and port 5 to access external memory.
Input
P67
Input
A/D converter analog input.
Input
P10-P17
D/A converter analog output.
Input
AV REF0
Input
AV REF1
Input
–
RESET
Input
X1
Input
X2
XT1
After Reset Alternate Function
Inserting wait for accessing external memory.
ANO0, ANO1 Output
AV SS
Funciton
A/D converter reference voltage input (shared with analog power
supply).
–
D/A converter reference voltage input.
–
–
A/D converter ground potential. Voltage equal to VSS0 .
–
–
System reset input.
–
–
Connecting crystal resonator for main system clock oscillation.
–
–
–
–
–
Input
P130, P131
–
Connecting crystal resonator for subsystem clock oscillation.
Input
P07
XT2
–
–
–
VDD0
–
Positive power supply voltage for ports.
–
–
VSS0
–
Ground potential of ports.
–
–
VDD1
–
Positive power supply (except ports and analog parts).
–
–
VSS1
–
Ground potential (except ports and analog parts).
–
–
VPP
–
Applying high-voltage for program write/verify.
Connected directly to VSS0 in normal operation mode.
–
–
13
mPD78F0058
2.3 Pin I/O Circuits and Recommended Connection of Unused Pins
Table 2-1 shows the I/O circuit type of each pin and the recommended connection of unused pins.
For the configuration of each I/O circuit type, refer to Figure 2-1.
Table 2-1. I/O Circuit Type of Each Pin (1/2)
Pin Name
I/O Circuit Type
I/O
P00/INTP0/TI00
2
Input
P01/INTP1/TI01
8-C
I/O
16
Input
11-D
I/O
Recommended Connection when Not Used
Connected to V SS0.
Independently connected to VSS0 through a resistor.
P02/INTP2
P03/INTP3
P04/INTP4
P05/INTP5
P07/XT1
P10/ANI0-P17/ANI7
P20/SI1
8-C
P21/SO1
5-H
P22/SCK1
8-C
P23/STB/TxD1
5-H
P24/BUSY/RxD1
8-C
P25/SI0/SB0
10-B
Connected to VDD0.
Independently connected to VDD0 or VSS0 through a resistor.
P26/SO0/SB1
P27/SCK0
P30/TO0
5-H
P31/TO1
P32/TO2
P33/TI1
8-C
P34/TI2
P35/PCL
5-H
P36/BUZ
P37
P40/AD0-P47/AD7
5-N
Independently connected to VDD0 through a resistor.
P50/A8-P57/A15
5-H
Independently connected to VDD0 or VSS0 through a resistor.
P60-P63
13-K
Independently connected to VDD0 through a resistor.
P64/RD
5-H
Independently connected to VDD0 or VSS0 through a resistor.
P65/WR
P66/WAIT
P67/ASTB
14
P70/SI2/RxD0
8-C
P71/SO2/TxD0
5-H
P72/SCK2/ASCK
8-C
P120/RTP0-P127/RTP7
5-H
P130/ANO0, P131/ANO1
12-C
Independently connected to VSS0 through a resistor.
mPD78F0058
Table 2-1. I/O Circuit Type of Each Pin (2/2)
Pin Name
I/O Circuit Type
I/O
RESET
2
Input
XT2
16
–
AVREF0
–
Recommended Connection when Not Used
–
Open
Connected to V SS0 .
AVREF1
Connected to VDD0 .
AVSS
Connected to V SS0 .
VPP
Connected directly to VSS0.
15
mPD78F0058
Figure 2-1. List of Pin I/O Circuits (1/2)
Type 2
Type 8-C
VDD0
pullup
enable
P-ch
VDD0
IN
data
P-ch
IN/OUT
output
disable
Schmitt trigger input with hysteresis characteristics
N-ch
VSS0
Type 5-H
Type 10-B
VDD0
pullup
enable
VDD0
pullup
enable
P-ch
P-ch
VDD0
data
VDD0
data
P-ch
P-ch
IN/OUT
output
disable
IN/OUT
open drain
output disable
N-ch
N-ch
VSS0
VSS0
input
enable
Type 5-N
pullup
enable
pullup
enable
VDD0
data
output
disable
Comparator
N-ch
P-ch
VSS0
+
N-ch
–
VSS0
input
enable
16
P-ch
IN/OUT
P-ch
IN/OUT
output
disable
P-ch
P-ch
VDD0
data
VDD0
Type 11-D
VDD0
N-ch
VSS0
VREF (threshold voltage)
mPD78F0058
Figure 2-1. List of Pin I/O Circuits (2/2)
Type 12-C
VDD0
pullup
enable
Type 16
feedback
cut-off
P-ch
VDD0
P-ch
data
P-ch
IN/OUT
output
disable
N-ch
VSS0
input
enable
P-ch
Analog output voltage
XT1
N-ch
XT2
VSS0
Type 13-K
IN/OUT
data
output disable
N-ch
VSS0
VDD0
RD
P-ch
Medium breakdown input buffer
17
mPD78F0058
3. MEMORY SIZE SWITCHING REGISTER (IMS)
This register sets a part of internal memory unused by software. The memory mapping can be made the same
as that of mask ROM versions with different types of internal memory (ROM and RAM) by setting the memory
size switching register (IMS).
The IMS is set with an 8-bit memory manipulation instruction.
RESET input sets the IMS to CFH.
Figure 3-1. Format of Memory Size Switching Register
Symbol
7
IMS
RAM2
6
5
RAM1 RAM0
4
0
3
2
1
0
ROM3 ROM2 ROM1 ROM0
Address
At reset
R/W
FFF0H
CFH
R/W
ROM3 ROM2 ROM1 ROM0 Selection of Internal ROM Capacity
0
1
1
0
24 Kbytes
1
0
0
0
32 Kbytes
1
0
1
0
40 Kbytes
1
1
0
0
48 Kbytes
1
1
1
0
56 KbytesNote
1
1
1
1
60 Kbytes
Setting prohibited
Others
RAM2 RAM1 RAM0
1
1
0
Others
Note
Selection of Internal High-speed RAM Capacity
1024 bytes
Setting prohibited
When using external device expansion function, set the internal ROM capacity to less than 56
Kbytes.
Table 3-1 shows the IMS set value to make the memory mapping the same as those of mask ROM versions.
Table 3-1. Set Value of Memory Size Switching Register
18
Target Mask ROM Versions
IMS Set Value
mPD780053
C6H
mPD780054
C8H
mPD780055
CAH
mPD780056
CCH
mPD780058
CFH
mPD78F0058
4. INTERNAL EXPANSION RAM SIZE SWITCHING REGISTER (IXS)
This register sets the internal expansion RAM capacity by software. The memory mapping can be made the
same as that of mask ROM versions with different types of internal expansion RAM by setting the internal expansion
RAM size switching register (IXS).
The IXS is set with an 8-bit memory manipulation instruction.
RESET input sets the IXS to 0AH.
Figure 4-1. Format of Internal Expansion RAM Size Switching Register
Symbol
7
6
5
4
IXS
0
0
0
0
3
2
1
0
IXRAM3 IXRAM2 IXRAM1 IXRAM0
Address
At reset
R/W
FFF4H
0AH
W
IXRAM3 IXRAM2 IXRAM1 IXRAM0 Selection of Internal Expansion RAM Capacity
1
1
0
0
0 bytes
1
0
1
0
1024 bytes
Others
Setting prohibited
Table 4-1 shows the IXS set value to make the memory mapping the same as those of mask ROM versions.
Table 4-1. Set Value of Internal Expansion RAM Size Switching Register
Target Mask ROM Versions
mPD780053
IMS Set Value
0CH
mPD780054
mPD780055
mPD780056
mPD780058
Remark
0AH
Even if a m PD78F0058 program in which MOV IXS, #0CH is written is executed on the m PD780055
and 780056, the operation will not be affected.
19
mPD78F0058
5. FLASH MEMORY PROGRAMMING
Writing to a flash memory can be performed without removing the memory from the target system (on-board).
Writing is performed connecting the dedicated flash programmer (Flashpro) to the host machine and the target
system.
Remark
Flashpro is a product of Naitou Densei Machidaseisakusho Co., Ltd.
5.1 Selection of Transmission Method
Writing to a flash memory is performed using the Flashpro with a serial transmission mode. One of the
transmission method is selected from those in Table 5-1. The selection of the transmission method is made by
using the format shown in Figure 5-1. Each transmission method is selected by the number of V PP pulses shown
in Table 5-1.
Table 5-1. List of Transmission Method
Transmission Method
3-wired serial I/O
Channels
3
Pin
P27/SCK0
VPP Pulses
0
P26/SO0/SB1
P25/SI0/SB0
P22/SCK1
1
P21/SO1
P20/SI1
P72/SCK2/ASCK
2
P71/SO2/TxD0
P70/SI1/RxD0
UART
2
P71/SO2/TxD0
8
P70/SI2/RxD0
P23/TxD1
9
P24/RxD1
Pseudo 3-wired serial
I/ONote
1
P32/TO2 (serial clock input/output)
12
P31/TO1 (serial data output)
P30/TO0 (serial data input)
Note
Serial transmission is performed by controlling the port using software.
Caution
Select a communication system always using the number of VPP pulses shown in Table
5-1.
20
mPD78F0058
Figure 5-1. Format of Transmission Method Selection
10 V
VPP
VDD
VSS
1
2
n
VDD
RESET
VSS
5.2 Function of Flash Memory Programming
Operations such as writing to a flash memory are performed by various command/data transmission and
reception operations according to the selected transmission method. Table 5-2 shows major functions of flash
memory programming.
Table 5-2. Major Functions of Flash Memory Programming
Functions
Descriptions
Reset
Used to stop write operation and detect transmission cycle.
Batch verify
Compares the entire memory contents with the input data.
Block verify
Compares the contents of the specified memory blocks with the input data.
Batch delete
Deletes the entire memory contents.
Block delete
Deletes the contents of the specified memory block, setting 16 Kbytes as one memory
block.
Convergence
Prevents over-deletion.
Batch blank check
Checks the deletion status of the entire memory.
Block blank check
Checks the deletion status of the specified block.
High-speed write
Performs write to the flash memory based on the write start address and the number of
data to be written (number of bytes).
Continuous write
Performs continuous write based on the information input with high-speed write
operation.
Status
Used to confirm the current operating mode and operation end.
Oscillation frequency setting
Sets the frequency of the resonator.
Delete time setting
Sets the memory delete time.
Baud rate setting
Sets the transmission rate in transmission using UART system.
Convergence time setting
Sets the correction time in convergence.
Silicon signature read
Outputs the device name and memory capacity, and device block information.
21
mPD78F0058
5.3 Connection of Flashpro
The connection of the Flashpro and the mPD78F0058 differs according to the transmission method. The
connection for each transmission method is shown in Figures 5-2 to 5-4.
Figure 5-2. Connection of Flashpro for 3-wired Serial I/O System
Flashpro
mPD78F0058
VPP
VPP
VDD
VDD
RESET
SCK
RESET
SCKn
SO
SIn
SI
SOn
GND
VSS
n = 0-2
Figure 5-3. Connection of Flashpro for UART System
Flashpro
mPD78F0058
VPP
VPP
VDD
VDD
RESET
n = 0, 1
22
RESET
TxD
RxDn
RxD
TxDn
GND
VSS
mPD78F0058
Figure 5-4. Connection of Flashpro for Pseudo 3-wired Serial I/O System
Flashpro
mPD78F0058
VPP
VPP
VDD
VDD
RESET
RESET
SCK
P32 (serial clock)
SO
P30 (serial input)
SI
GND
P31 (serial output)
VSS
23
mPD78F0058
6. PACKAGE DRAWINGS
80-pin plastic QFP (14 ¥ 14) (Unit: mm)
80 PIN PLASTIC QFP (14·14)
A
B
60
61
41
40
detail of lead end
C D
S
R
Q
21
20
80
1
F
J
G
I
H
M
K
P
M
N
L
NOTE
Each lead centerline is located within 0.13 mm (0.005 inch) of
its true position (T.P.) at maximum material condition.
ITEM
MILLIMETERS
INCHES
A
17.2±0.4
0.677±0.016
B
14.0±0.2
0.551 +0.009
–0.008
C
14.0±0.2
0.551 +0.009
–0.008
D
17.2±0.4
0.677±0.016
F
0.825
0.032
G
0.825
0.032
H
0.30±0.10
0.012 +0.004
–0.005
I
0.13
0.005
J
0.65 (T.P.)
0.026 (T.P.)
K
1.6±0.2
L
0.8±0.2
0.063±0.008
0.031 +0.009
–0.008
M
0.15 +0.10
–0.05
0.006 +0.004
–0.003
N
0.10
0.004
P
2.7
0.106
Q
0.1±0.1
0.004±0.004
R
5 ±5
5 ±5
S
3.0 MAX.
0.119 MAX.
S80GC-65-3B9-4
24
mPD78F0058
80-pin plastic QFP (14 ¥ 14) (Unit: mm)
80 PIN PLASTIC QFP (14·14)
A
B
60
61
41
40
detail of lead end
C
S
D
R
Q
80
1
21
20
F
G
H
I
M
J
P
K
M
N
NOTE
Each lead centerline is located within 0.13 mm (0.005 inch) of
its true position (T.P.) at maximum material condition.
L
ITEM
MILLIMETERS
INCHES
A
17.20±0.20
0.677±0.008
B
14.00±0.20
0.551 +0.009
–0.008
C
14.00±0.20
0.551 +0.009
–0.008
D
17.20±0.20
0.677±0.008
F
0.825
0.032
G
0.825
0.032
H
0.32±0.06
0.013 +0.002
–0.003
I
0.13
0.005
J
0.65 (T.P.)
0.026 (T.P.)
K
1.60±0.20
0.063±0.008
L
0.80±0.20
0.031 +0.009
–0.008
M
0.17 +0.03
–0.07
0.007 +0.001
–0.003
N
0.10
0.004
P
1.40±0.10
0.055±0.004
Q
0.125±0.075
0.005±0.003
R
3 +7
–3
3 +7
–3
S
1.70 MAX.
0.067 MAX.
P80GC-65-8BT
25
mPD78F0058
80-pin plastic TQFP (fine pitch) (12 ¥ 12) (Unit: mm)
80 PIN PLASTIC TQFP (FINE PITCH) (
12)
A
B
60
41
61
40
21
F
80
1
20
H
I
M
J
K
M
P
G
R
Q
S
D
C
detail of lead end
N
L
NOTE
Each lead centerline is located within 0.10 mm (0.004 inch) of
its true position (T.P.) at maximum material condition.
ITEM MILLIMETERS
A
14.0±0.2
INCHES
0.551 +0.009
–0.008
B
12.0±0.2
0.472 +0.009
–0.008
C
12.0±0.2
0.472 +0.009
–0.008
D
14.0±0.2
0.551 +0.009
–0.008
F
1.25
0.049
G
1.25
0.049
H
0.22 +0.05
–0.04
I
0.10
J
0.5 (T.P.)
K
1.0±0.2
0.039 +0.009
–0.008
L
0.5±0.2
0.020 +0.008
–0.009
M
0.145 +0.055
–0.045 0.006±0.002
N
0.10
P
1.05
Q
0.05±0.05
R
5°±5°
S
1.27 MAX.
0.009±0.002
0.004
0.020 (T.P.)
0.004
0.041
0.002±0.002
5°±5°
0.050 MAX.
P80GK-50-BE9-4
26
mPD78F0058
APPENDIX A. DEVELOPMENT TOOLS
The following development tools are available for system development using the m PD78F0058.
Language Processing Software
RA78K/0Notes 1, 2, 3, 4
78K/0 Series common assembler package
CC78K/0Notes 1, 2, 3, 4
78K/0 Series common C compiler package
DF780058Notes 1, 2, 3, 4, 8
Device file for mPD780058 Subseries
CC78K/0-LNotes 1, 2, 3, 4
78K/0 Series common C compiler library source file
Flash Memory Writing Tools
Flashpro II (FL-PR2)
Dedicated flash writter
Product of Naitou Densei Machidaseisakusho Co., Ltd.
FA-80GCNote 8
Adapter for flash memory writting
FA-80GKNote 8
Product of Naitou Densei Machidaseisakusho Co., Ltd.
Debugging Tool
IE-78000-R
78K/0 Series common in-circuit emulator
IE-78000-R-A
78K/0 Series common in-circuit emulator (for integrated debugger)
IE-78000-R-BK
78K/0 Series common brake board
IE-780308-R-EM
mPD780308 Subseries common emulation board
EP-780058GC-RNote 8
Emulation probe for mPD780058 Subseries
EV-9200GC-80
Socket to be mounted on a target system board made for the 80-pin plastic QFP (GC-3B9,
GC-8BT type)
EP-780058GK-RNote 8
Emulation probe for mPD780058 Subseries
TGK-080SDW
Adapter to be mounted on a target system board made for the 80-pin plastic QFP (GK-BE9
type)
Product of TOKYO ELETECH Corporation
Consult NEC sole agent for purchase.
SM78K0Notes 5, 6, 7
78K/0 Series common system simulator
ID78K0Notes 4, 5, 6, 7
Integrated debugger for IE-78000-R-A
SD78K/0Notes 1, 2
Screen debugger for IE-78000-R
DF780058Notes 1, 2, 3, 4, 5, 6, 7, 8
Device file for mPD780058 Subseries
Notes 1. PC-9800 Series (MS-DOSTM) based
2. IBM PC/ATTM and compatibles (PC DOSTM/IBM DOSTM/MS-DOS) based
3. HP9000 Series 300TM (HP-UXTM) based
4. HP9000 Series 700TM (HP-UX) based, SPARCstation TM (SunOSTM) based, EWS4800 Series
(EWS-UX/V) based
5. PC-9800 Series (MS-DOS + WindowsTM) based
6. IBM PC/AT and compatibles (PC-DOS/IBM DOS/MS-DOS + Windows) based
7. NEWSTM (NEWS-OSTM) based
8. Under development
27
mPD78F0058
Real-time OS
RX78K/0Notes 1, 2, 3, 4
78K/0 Series real-time OS
MX78K0Notes 1, 2, 3, 4
78K/0 Series OS
Fuzzy Inference Development Support System
FE9000Note 1 /FE9200Note 5
Fuzzy knowledge data creation tool
FT9080Note 1 /FT9085Note 2
Translator
FI78KNotes 1, 2
Fuzzy inference module
FD78K0 Notes 1, 2
Fuzzy inference debugger
Notes 1. PC-9800 Series (MS-DOS) based
2. IBM PC/AT and compatibles (PC DOS/IBM DOS/MS-DOS) based
3. HP9000 Series 300 (HP-UX) based
4. HP9000 Series 700 (HP-UX) based, SPARCstation (SunOS) based, EWS4800 Series (EWS-UX/V)
based
5. IBM PC/AT and compatibles (PC DOS/IBM DOS/MS-DOS + Windows) based
Remarks 1. For third party development tools, refer to the 78K/0 Series Selection Guide (U11126E)
2. The RA78K/0, CC78K/0, SM78K0, ID78K0, SD78K/0, and RX78K/0 are used in combination with
the DF780058.
28
mPD78F0058
APPENDIX B. RELATED DOCUMENTS
Device Related Documents
Document No.
Document Name
Japanese
English
mPD780058, 780058Y Subseries User’s Manual
U12013J
Planned
mPD780053, 780054, 780055, 780056, 780058 Preliminary Product Information
U12182J
Planned
mPD78F0058 Preliminary Product Information
U12092J
This manual
78K/0 Series User’s Manual Instruction
IEU-849
IEU-1372
78K/0 Series Instruction Table
U10903J
–
78K/0 Series Instruction Set
U10904J
–
Development Tools Documents (User’s Manual)
Document No.
Document Name
RA78K Series Assembler Package
Japanese
English
Operation
EEU-809
EEU-1399
Language
EEU-815
EEU-1404
EEU-817
EEU-1402
Operation
EEU-656
EEU-1280
Language
EEU-655
EEU-1284
Operation
U11517J
U11517E
Language
U11518J
U11518E
Programming Know-how
EEA-618
EEA-1208
CC78K Series Library Source File
EEU-777
–
IE-78000-R
EEU-810
U11376E
IE-78000-R-A
U10057J
U10057E
IE-78000-R-BK
EEU-867
EEU-1427
IE-78308-R-EM
U11362J
U11362E
EP-780058GC-R
Planned
Planned
EP-780058GK-R
Planned
Planned
RA78K Series Structured Assembler Preprocessor
CC78K Series C Compiler
CC78K0 C Compiler
CC78K/0 C Compiler Application Note
SM78K0 System Simulator Windows based
Reference
U10181J
U10181E
SM78K Series System Simulator
External Parts User Open
Interface Specification
U10092J
U10092E
ID78K0 Integrated Debugger EWS based
Reference
U11151J
ID78K0 Integrated Debugger PC based
Reference
U11539J
U11539E
ID78K0 Integrated Debugger Windows based
Guide
U11649J
U11649E
SD78K0 Screen Debugger
Introduction
EEU-852
–
PC-9800 Series (MS-DOS) based
Reference
U10952J
–
SD78K/0 Screen Debugger
Guide
EEU-5024
EEU-1414
IBM PC/AT (PC DOS) based
Reference
U11279J
U11279E
Caution
–
The contents of the above related documents are subject to change without notice. The latest
documents should be used for design, etc.
29
mPD78F0058
Embedded Software Documents (User’s Manual)
Document No.
Document Name
78K/0 Series Real-time OS
OS for 78K/0 Series MX78K0
Japanese
English
Basic
U11537J
–
Installation
U11536J
–
Technical
U11538J
–
Basic
EEU-5010
–
Fuzzy Knowledge Data Creation Tool
EEU-829
EEU-1438
78K/0, 78K/II, 87AD Series Fuzzy Inference Development Support System Translator
EEU-862
EEU-1444
78K/0 Series Fuzzy Inference Development Support System Fuzzy Inference Module
EEU-858
EEU-1441
78K/0 Series Fuzzy Inference Development Support System Fuzzy Inference Debugger
EEU-921
EEU-1458
Other Documents
Document No.
Document Name
Japanese
English
IC PACKAGE MANUAL
C10943X
Semiconductor Device Mounting Technology Manual
C10535J
C10535E
Quality Grade on NEC Semiconductor Devices
C11531J
C11531E
Reliable Quality Maintenance on NEC Semiconductor Devices
C10983J
C10983E
Electrostatic Discharge (ESD) Test
MEM-539
Semiconductor Devices Quality Guarantee Guide
C11893J
Microcomputer Product Series Guide
U11416J
Caution
MEI-1202
–
The contents of the above related documents are subject to change without notice. The latest
documents should be used for design, etc.
30
–
mPD78F0058
[MEMO]
31
mPD78F0058
[MEMO]
32
mPD78F0058
[MEMO]
33
mPD78F0058
NOTES FOR CMOS DEVICES
1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note: Strong electric field, when exposed to a MOS device, can cause destruction
of the gate oxide and ultimately degrade the device operation. Steps must be
taken to stop generation of static electricity as much as possible, and quickly
dissipate it once, when it has occurred.
Environmental control must be
adequate. When it is dry, humidifier should be used. It is recommended to
avoid using insulators that easily build static electricity. Semiconductor
devices must be stored and transported in an anti-static container, static
shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded
using wrist strap. Semiconductor devices must not be touched with bare
hands. Similar precautions need to be taken for PW boards with semiconductor
devices on it.
2 HANDLING OF UNUSED INPUT PINS FOR CMOS
Note: No connection for CMOS device inputs can be cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input
level may be generated due to noise, etc., hence causing malfunction. CMOS
device behave differently than Bipolar or NMOS devices. Input levels of CMOS
devices must be fixed high or low by using a pull-up or pull-down circuitry.
Each unused pin should be connected to VDD or GND with a resistor, if it is
considered to have a possibility of being an output pin. All handling related
to the unused pins must be judged device by device and related specifications
governing the devices.
3 STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note: Power-on does not necessarily define initial status of MOS device. Production
process of MOS does not define the initial operation status of the device.
Immediately after the power source is turned ON, the devices with reset
function have not yet been initialized. Hence, power-on does not guarantee
out-pin levels, I/O settings or contents of registers. Device is not initialized
until the reset signal is received. Reset operation must be executed immediately
after power-on for devices having reset function.
34
mPD78F0058
Regional Information
Some information contained in this document may vary from country to country. Before using any NEC
product in your application, please contact the NEC office in your country to obtain a list of authorized
representatives and distributors. They will verify:
• Device availability
• Ordering information
• Product release schedule
• Availability of related technical literature
• Development environment specifications (for example, specifications for third-party tools and
components, host computers, power plugs, AC supply voltages, and so forth)
• Network requirements
In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary
from country to country.
NEC Electronics Inc. (U.S.)
NEC Electronics (Germany) GmbH
NEC Electronics Hong Kong Ltd.
Santa Clara, California
Tel: 800-366-9782
Fax: 800-729-9288
Benelux Office
Eindhoven, The Netherlands
Tel: 040-2445845
Fax: 040-2444580
Hong Kong
Tel: 2886-9318
Fax: 2886-9022/9044
NEC Electronics (Germany) GmbH
Duesseldorf, Germany
Tel: 0211-65 03 02
Fax: 0211-65 03 490
NEC Electronics Hong Kong Ltd.
Velizy-Villacoublay, France
Tel: 01-30-67 58 00
Fax: 01-30-67 58 99
Seoul Branch
Seoul, Korea
Tel: 02-528-0303
Fax: 02-528-4411
NEC Electronics (France) S.A.
NEC Electronics Singapore Pte. Ltd.
Spain Office
Madrid, Spain
Tel: 01-504-2787
Fax: 01-504-2860
United Square, Singapore 1130
Tel: 253-8311
Fax: 250-3583
NEC Electronics (France) S.A.
NEC Electronics (UK) Ltd.
Milton Keynes, UK
Tel: 01908-691-133
Fax: 01908-670-290
NEC Electronics Italiana s.r.1.
Milano, Italy
Tel: 02-66 75 41
Fax: 02-66 75 42 99
NEC Electronics Taiwan Ltd.
NEC Electronics (Germany) GmbH
Scandinavia Office
Taeby, Sweden
Tel: 08-63 80 820
Fax: 08-63 80 388
Taipei, Taiwan
Tel: 02-719-2377
Fax: 02-719-5951
NEC do Brasil S.A.
Sao Paulo-SP, Brasil
Tel: 011-889-1680
Fax: 011-889-1689
J96. 8
35
mPD78F0058
FIP, IEBus, and QTOP are trademarks of NEC Corporation.
MS-DOS and Windows are trademarks of Microsoft Corporation.
IBM DOS, PC/AT, and PC DOS are trademarks of IBM Corporation.
HP9000 Series 300, HP9000 Series 700, and HP-UX are trademarks of Hewlett-Packard Company.
SPARCstation is a trademark of SPARC International, Inc.
SunOS is a trademark of Sun Microsystems, Inc.
NEWS and NEWS-OS are trademarks of Sony Corporation.
The related documents indicated in this publication may include preliminary versions. However, preliminary
versions are not marked as such.
No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in
this document.
NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property
rights of third parties by or arising from use of a device described herein or any other liability arising from use
of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of NEC Corporation or others.
While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices,
the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or
property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety
measures in its design, such as redundancy, fire-containment, and anti-failure features.
NEC devices are classified into the following three quality grades:
"Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a
customer designated "quality assurance program" for a specific application. The recommended applications of
a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device
before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems or medical equipment for life support, etc.
The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those specified for Standard quality grade,
they should contact an NEC sales representative in advance.
Anti-radioactive design is not implemented in this product.
M4 96.5
36
Download PDF