INNO SPOT PRO - Quality Music

INNO SPOT PRO
©2013 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product.
User Instructions
10/13
Inno Spot Pro
General Information
Unpacking: Thank you for purchasing the Inno Spot Pro by ADJ
Products, LLC. Every Inno Spot Pro has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your fixture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support first.
Introduction: The Inno Spot Pro is a 14 channel, DMX intelligent,
moving head, LED fixture. The Inno Spot Pro can operate as a stand
alone fixture or in a Master/Slave configuration. The Inno Spot Pro has
three operating modes; a sound active, show mode, DMX controlled.
This fixture is suitable for theaters, studios, retail stores, and other
similar locations. For best results use fog or special effects smoke to
enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@adj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
Inno Spot Pro
General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Inno Spot Pro
•
•
•
•
•
•
•
•
•
Features
DMX-512 Protocol Compatible (14 DMX Channels)
8 Colors + White
6 Rotating, Replaceable Gobos + Spot
3 Operating Modes - Sound Active, Show Mode, & DMX Control
Power Cord Daisy Chain - See page 20 for more info
Internal Microphone
Digital Display for Address and Function Setting
UC3 Controller (Not Included)
4 Preprogrammed Shows
Inno Spot Pro
Warranty Registration
The Inno Spot Pro carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www. adjproducts.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
Inno Spot Pro
Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 2
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to this unit.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 3
Inno Spot Pro
Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required voltage for your unit.
•Do not attempt to operate this unit if the power cord has been
frayed or broken.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 25 for cleaning details.
•Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 4
Inno Spot Pro
Installation
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualifications, do not attempt the installation yourself.
These installaiton should be checked by a skilled person once a year.
The Inno Spot Pro is fully operational in two different mounting positions, hanging upside-down from a ceiling or set on a flat level surface. To avoid internal damage to the unit, never mount the unit on
its side as illustrated above. Be sure this fixture is kept at least 0.5m
away from any flammable materials (decoration etc.). Always use
and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails (see next
page). Never use the carrying handles for secondary attachment.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 5
Inno Spot Pro
Installation
NOTICE: The suitable enviromental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place this lighting
fixture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the fixture
to run at its best and help prolong the fixture life.
Inno Spot Pro
Set Up
Power Supply: The ADJ Inno Spot Pro contains a automatic voltage switch, which will auto sense the voltage when it is plugged into
a power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Screw one clamp via a M12 screw and nut onto the Omega
holder. Insert the quick-lock fasteners of the Omega holder
into the respective holes on the bottom of the Inno Spot Pro.
Tighten the quick-lock fasteners fully clockwise. Screw in the
included Eye Hole screw to the base and pull the safety-cable
through the eye hole and over the trussing system or a safe
fixation spot. Insert the end in the carabine and tighten the
safety screw.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 6
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Inno Spot Pro can be controlled via DMX-512 protocol. The Inno Spot Pro is a 14 channel DMX unit. The DMX address
is set electronically using the controls on the front
panel of the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data
cable for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
Figure 1
lighting stores). Your cables should be made with
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 7
Inno Spot Pro
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
SOUND
Set Up
INPUT
OUTPUT
a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
POWER
POWER
Notice: Be sure to follow
figures two and three when making your own
DMX512
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
DMX512 OUT
3-PIN XLR
1
2
DMX +
3
DMX -
3
1
DMX512 IN
3-PIN XLR
2
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
REMOTE
CONTROL
INPUT
SOUND
2 Cold
2 Cold
INPUT
OUTPUT
1 Ground
3 Hot
Inno Spot Pro
REMOTE
CONTROL
INPUT
INPUT
Set Up
OUTPUT
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
POWER
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Pin 3
Pin 3
Termination reduces signal errors and
Data
True (+ signal)
avoids signal transmission
problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
Not Used
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Not Used
Pin 4 - Do Not Use
Pin 5 - Do Not Use
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
SOUND
SOUND
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
POWER
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 8
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 9
Inno Spot Pro
System Menu
Inno Spot Pro
System Menu
DMX Address - Set the DMX Address -
1. Press the MENU button until “DMX Addresss” is displayed,
press ENTER.
2. “X” will now be displayed, “X” represents the displayed
address. Press the UP or DOWN buttons to find your desired
address.
3. Press ENTER to confirm, and then press and hold the MENU
button for at least three seconds to assign.
Show Mode - Show modes 1 - 4 (Factory Shows).
1. Press the MENU button until “Show Mode” is displayed, press
ENTER.
2. “Show X” will now be displayed, “X” representing a number
between 1-4. Press the UP or DOWN buttons to find your desired
show and press ENTER to confirm. After pressing ENTER, press
and hold the MENU button for at least 3 seconds to activate.
SHOWS:
Show 1 - For fixtures placed on the floor, the tilt movement angle is
210°
Show 2 - For fixtures fixed to the ceiling or truss, the tilt movement
angle is 90°.
Show 3 - For fixtures placed on a table or stage. The beam is projected at the audience’s direction; i.e. in front of the stage. Pan movement angle (left to right to left) is 160°. Tilt movement angle is 90°.
Show 4 - For fixtures fixed to the ceiling or truss. The beam is projected at the audience’s direction; i.e. in front of the stage. Pan movement angle (left to right to left) is 160°. Tilt movement angle is 90°.
Slave Mode - This will let you set unit as a slave in a
master/slave configuration.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 10
1. Press the MENU button until “Slave Mode” is displayed,
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 11
Inno Spot Pro
System Menu
Inno Spot Pro
press ENTER. Either “Slave 1” or “Slave 2” will be displayed.
100 (most sensitive).
2. Press the UP or DOWN buttons until your desired slave
mode is displayed, press ENTER to confim.
3. Press ENTER to set you desired level.
System Menu
NOTE: In a Master/Slave configuration you can make one
fixture the Master and then set the next fixture to “Slave 2”, the
fixtures will now have contrast movement to each other.
Pan Inverse - Pan Inversion
Black Out - This will control blackout
2. To activate the Pan inversion press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to confim. To deactivate
Pan inversion, select “No” and press Enter.
2. Either “Yes” or “No” will now be displayed. Press the UP or
DOWN buttons to toggle between “Yes” and “No”.
Tilt Inverse - Tilt Inversion
1. Press the MENU button until “Black Out” is displayed, press
ENTER.
3. Press ENTER to confirm your setting.
1. Press the MENU button until “Pan Inverse” is displayed,
press ENTER. Either “Yes” or “No” will be displayed.
1. Press the MENU button until “Tilt Inverse” is displayed, press
ENTER. Either “Yes” or “No” will be displayed.
active mode.
2. To activate the Tilt inversion press the UP or DOWN buttons
until “Yes” is displayed, press ENTER to confim. To deactivate
Tilt inversion, select “No” and press Enter.
1. Press the MENU button until “Sound State” is displayed, press
ENTER.
Back Light - With this function you can make the back-
Sound State - In this mode the unit will run in sound
2. Either “On” or “Off” will now be displayed. Use the UP or
DOWN buttons to toggle between “On” and “Off”.
3. Press ENTER to confirm your selection, the press and hold the
MENU button to activate.
Sound Sense - In this mode you can adjust the sound
sensitivity of the sound active mode.
1. Press the MENU button until “Sound Sense” is displayed,
press ENTER.
2. Press the UP or DOWN buttons to adjust the sensitivity level.
The sensitivity level can be adjusted between 0 (the lowest) and
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 12
light automatically turn off after one minute.
1. Press the MENU button until “Back Light” is displayed, press
ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or
DOWN buttons to select “ON” to keep the backlight on at all
times, or “OFF” to allow the backlight to turn off after 2 minutes.
Press any button to turn the backlight on again.
3. Press ENTER to confirm.
Dimmer Calibrat - With this function you can set the
output intensity.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 13
Inno Spot Pro
System Menu
1. Press the MENU button until “Dimmer Calibrat” is displayed,
press ENTER.
2. A number between 50-100 will be displayed. This number represents the instensity setting. Use the UP or DOWN buttons to
adjust the LED output intensity. 50 being medium intensity, and
100 being full intensity.
3. When you have found your desired setting press ENTER to
confirm.
Auto Test - This function will run a self test program.
1. Press the MENU button until “Auto Test” is displayed, press
ENTER.
Inno Spot Pro
System Menu
Fixture Version - This will display the software version
1. Tap the MENU button until “Fixture Version” is displayed. Press
the ENTER button and the software vesion will be displayed.
2. Press the MENU button to leave this function.
Reset - Use this function to reset the unit.
1. Tap the MENU button until “Reset” is displayed, press
ENTER.
2. The fixture will now reset.
2. The fixture will now run a self test. Press the MENU button to
exit.
Temp. - With this function you can display the running
temperature of the unit.
1. Tap the MENU button until “Temp.” is displayed, press
ENTER.
2. The current running temperature of the fixture will now be
displayed. Press MENU to exit.
Fixture Time - With this function you can display the
running time of the unit.
1. Tap the MENU button until “Fixture Time” is displayed, press
ENTER.
2. The running time of the fixture will now be displayed. Press
MENU to exit.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 14
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 15
Inno Spot Pro
System Menu
Inno Spot Pro
System Menu
Color Offset - Home setting adjustment for the color
wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Color Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
Gobo Offset - Home setting adjustment for the gobo
wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Gobo Offset” is displayed, press ENTER.
To enter the OTIL (Home position adjustment) & Gobo wheel adjustment submenu, press the ENTER button for at least 3 seconds. In
this submenu you are able to adjust the home position of the pan,
tilt, color wheel, gobo wheel, RGobo (Rotating) wheel, prism, RPrism,
and focus position.
Pan Offset - Adjustment of the pan home position.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Pan Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
Tilt Offset - Adjustment of the tilt home position.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Tilt Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 16
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
RGobo Offset - Home setting adjustment for the
rotating gobo.
1. Press the ENTER button for at least 3 seconds, then press the
UP or DOWN buttons so that “RGobo Offset” is displayed, press
ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
Prism Offset - Home setting adjustment for the prism.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “Prism Offset” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 17
Inno Spot Pro
System Menu
RPrism Offset - Home setting adjustment for the
rotating prism.
1. Press the ENTER button for at least 3 seconds, then press the
UP or DOWN buttons so that “RPrism Offset” is displayed, press
ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
Focus Offset - Home setting adjustment for the
focus.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “focus” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
Inno Spot Pro
Operation
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit find your desired show and set that show by pressing the ENTER button.
3. On the slave units tap the MENU button until “Slave Mode” is displayed, and Press ENTER. Choose either “Slave 1” or “Slave 2” and press ENTER. See pages 11-12 for more info.
4. The slave units will now follow the Master unit.
Universal DMX Control: This function allows you to use a
Elation® universal DMX-512 controller to control the chases and
patterns, dimmer and strobe. A DMX controller allows you to create
unique programs tailored to your individual needs.
1. The Inno Spot Pro is a 14 channel DMX fixture. See pages 21-23 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 11 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “Sound State” is displayed, and ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 18
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 19
Inno Spot Pro
Operation
press ENTER. Tap the UP or DOWN buttons so that “ON” is dis
played and press ENTER.
2. To adjust the sound sensitivity, press MENU button until “Sound Sense” is displayed and press ENTER.
3. Use the UP and DOWN buttons to adjust the sensitivity, and press ENTER when you have found your desired sensitivity level.
4. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Inno Spot Pro
Channel
1
2
3
4
5
Show Mode: This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until “Show Mode” is displayed, and press ENTER.
2. Press the UP or DOWN buttons until you find your desired show, and press ENTER.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Inno Spot Pro
Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can
be connected is 4 fixtures max (120V) and 8 fixtures max (220V).
After the maximum fixtures has been reached you will need to
use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
Inno Spot Pro
UC3 Control
The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Stand By
Blackout the unit
Function
1. Sync. Strobe
Show
1. Select Color
2. Async strobe
1-4
2. Select Gobo
Show (LED
LED ON
3. Sound Strobe
Mode
Sound (LED OFF)
Slow Blinking)
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 20
6
Value
0 - 255
0 - 255
0 - 255
0 - 255
0-7
8 - 14
15 - 21
22 - 28
29 - 35
36 - 42
43 - 49
50 - 56
57 - 63
64 - 127
128 - 189
190 - 193
194 - 255
0-9
10 - 18
19 - 27
28 - 36
37 - 45
46 - 54
55 - 63
64 - 73
74 - 82
83 - 91
92 - 100
101 - 109
110 - 118
119 - 127
128 - 189
190 - 193
194 - 255
DMX Traits
Function
PAN
PAN FINE
TILT
TILT FINE
COLORS
WHITE
RED
ORANGE
YELLOW
GREEN
BLUE
PURPLE
LIGHT BLUE
PINK
COLOR MIXING
CLOCKWISE ROTATION FAST - SLOW
STOP
COUNTER CLOCKWISE ROTATION
SLOW - FAST
GOBO WHEEL
SPOT
GOBO 1
GOBO 2
GOBO 3
GOBO 4
GOBO 5
GOBO 6
SPOT SHAKE
GOBO 1 SHAKE
GOBO 2 SHAKE
GOBO 3 SHAKE
GOBO 4 SHAKE
GOBO 5 SHAKE
GOBO 6 SHAKE
GOBO WHEEL ROTATION SLOW - FAST
STOP
GOBO WHEEL ROTATION FAST - SLOW
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 21
Inno Spot Pro
Channel
7
8
9
10
11
12
13
14
Value
0 - 127
128 - 189
190 - 193
194 - 255
0-7
8 - 255
0 - 127
128 - 189
190 - 193
194 - 255
0 - 255
0-7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
0 - 255
0 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 129
130 - 199
DMX Traits
Inno Spot Pro
Function
Channel
GOBO ROTATION
COUNTER-CLOCKWISE INDEX 0°-360°
CLOCKWISE FAST - SLOW
STOP
COUNTER-CLOCKWISE SLOW - FAST
PRISM
NO EFFECT
PRISM EFFECT
PRISM ROTATION
COUNTER-CLOCKWISE INDEX 0°-360°
COUNTER-CLOCKWISE FAST - SLOW
STOP
CLOCKWISE SLOW - FAST
FOCUS
ZOOM OUT - ZOOM IN
SHUTTER/STROBE
BLACKOUT
SHUTTER OPEN
STROBING SLOW - FAST
SHUTTER OPEN
SHUTTER SLOW OPEN - FAST CLOSE
SHUTTER OPEN
SHUTTER SLOW CLOSE - FAST OPEN
SHUTTER OPEN
RANDOM STROBE
SHUTTER OPEN
DIMMER 0% - 100%
MOVEMENT SPEED FAST - SLOW
BLACKOUT/RESET
NOTHING
BLACKOUT W/ PAN/TILT MOVEMENT
NO BLACKOUT PAN TILT MOVEMENT
BLACKOUT W/ COLOR CHANGE
NO BLACKOUT W/ COLOR CHANGE
BLACKOUT W/ GOBO CHANGE
NO BLACKOUT W/ GOBO CHANGE
NOTHING
14
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 22
Value
200 - 209
210 - 255
Inno Spot Pro
DMX Traits
Function
BLACKOUT/RESET
RESET ALL
NOTHING
Photometric Chart
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 23
Inno Spot Pro
Gobo Replacement
Inno Spot Pro
This unit comes with interchangable gobos. When changing the
gobos please be very careful.
Caution! Never open the unit when in use. Always disconnect
the main power before attempting to change the gobos.
1. To change the gobo, you must remove the top half of the moving head. The top half of the moving head does not have the lens attached to it.
2. Unscrew the 4 phillips screws that secure the top half of the
head. Remove the top half of the head.
3. When you remove the shell you will be able to access the gobo wheel (see picture below). Rotate the head so that the lens is aimed up. Turn the gobo wheel with your hand until
you find the gobo you would like to change.
4. Using a pair of needle nose pliers, grab the fixture ring that holds the gobo in place and remove the ring.
5. Once the ring is removed, rotate the head upside down so that the gobo falls into your hand.
6. Carefully insert your new gobo and insert the fixture ring.
7. Reassemble the unit.
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Inno Spot Pro
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
Inno Spot Pro
Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1.
Be sure the external fuse has not blown. The fuse is located on the rear panel of the unit.
2.Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 24
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 25
Inno Spot Pro
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 3-year (1095 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
ADJ Products, LLC - www.adj.com - Inno Spot ProInstruction Manual Page 26
Inno Spot Pro
Model: Inno Spot Pro
Specifications
Voltage:
100 - 240V, 50/60Hz
LED:
1 x 60W White LED
Power Consumption:
140W @ 110V / 134W @ 220V
Power Cord Daisy Chain: 4 Fixtures Max. (120V)
8 Fixtures Max. (220V)
Dimensions: 11.5”(L) x 6.75”(W) x 16.75”(H)
288mm x 167mm x 425mm
Weight:
10 Lbs. / 9 kgs.
Beam Angle:
12 - 17 Degrees
Fuse:
1 Amp
Duty Cycle:
None
DMX: 14 DMX Channels
Colors:8 + White
Gobos:
6 + Spot
24mm/0.2mm thickness (Metal Gobo)
1.1mm thickness (Glass Gobo)
(20mm viewable)
Working Position:
Any Safe, Secure Position
Warranty:
3 Year (1095 days)
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Download PDF