HVE Audio Video Encoders User Guide

HVE
Audio/Video Encoders
HVE1
HVE4
HVE8
HVE1X
HVE4X
HVE8X
User Guide
Document 800-15877V1 – Rev A – 10/2013
User Guide
Revisions
Issue
Date
Revisions
A
09/2013
New document.
Va Rev A
10/2013
Added Index. Minor text updates throughout. Updated the data storage capacity and
network protocols in the Specifications section. Added an index. Added a section in
chapter 6 about setting the RS-232 port as a transparent channel.
Contents | 5
Contents
1
About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Overview of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1
Introduction . . . . . .
Features . . . . . . . .
Encoding Features
Network Features .
PTZ. . . . . . . . .
Alarm. . . . . . . .
Exceptions . . . . .
Logs . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
21
22
22
22
23
23
23
24
2
Installing an HVE Encoder . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Hard Disk Drive (HDD) [HVE8(X) only] . . . .
Preparing for Installation . . . . . . . . . . . . . . . .
Installing the HDD. . . . . . . . . . . . . . . . . . . .
HVE1/HVE1X Encoder Front and Rear Panels. . . . . . . . . .
HVE4/HVE4X Encoder Front and Rear Panels. . . . . . . . . .
HVE8/HVE8X Encoder Front and Rear Panels. . . . . . . . . .
Connecting Alarms . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Alarm Inputs . . . . . . . . . . . . . . . . . .
Alarm Input Connections for an Emerson Alarm . . . .
Alarm Input Connections for a Normal Alarm . . . . .
Connecting Alarm Outputs . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
25
25
25
26
26
28
30
32
33
33
33
34
34
3
Connecting to an HVE Encoder via the Internet . . . . . . .
Installing the IP Utility. . . . . . . . . . . . . . . . . . . . . . .
Configuring Network Parameters . . . . . . . . . . . . . . . .
Searching for Online Devices . . . . . . . . . . . . . . . .
Automatically Searching for Online Devices . . . . . .
Manually Searching for Online Devices . . . . . . . .
Modifying Network Parameters. . . . . . . . . . . . .
Connecting to an Online IP Device . . . . . . . . . . . . .
Accessing an HVE Encoder Through a Web Browser . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
37
37
39
39
39
40
41
42
42
4
Viewing Live Video . . . . . . . . . . . . . . . . . . . . . .
Starting Live View. . . . . . . . . . . . . . . . . . . . . . . . .
Starting Live View for All Cameras . . . . . . . . . . . . .
Live View Toolbar . . . . . . . . . . . . . . . . . . . . . .
Full Screen Mode . . . . . . . . . . . . . . . . . . . . . .
Capturing an Image . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Save Path for Captured Images . . . . . .
Controlling a PTZ Camera . . . . . . . . . . . . . . . . . . . .
Connecting to a PTZ Camera . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
45
45
46
46
46
47
47
47
48
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
800-15877V1 - A - 10/2013
6 | HVE Encoders User Guide
Configuring for a PTZ Camera .
Controlling a PTZ Camera . . . .
Setting and Calling Presets .
Linking a Preset to an Alarm. . .
Configuring Video Parameters . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
48
48
49
50
50
. . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
5
Configuring the Encoder . . . . . . .
Configuring Time Settings . . . . . . .
Configuring Network Settings . . . . .
Configuring TCP/IP Settings. . . .
Configuring Port Settings . . . . .
Configuring DDNS Settings . . . .
Configuring PPPoE Settings. . . .
Configuring Email Settings . . . .
Adding the Network Disk . . . . .
Configuring SNMP Settings . . . .
Configuring QoS Settings . . . . .
Configuring FTP Settings . . . . .
Configuring SOCKS Settings . . .
Configuring UPnP™ Settings . . .
Configuring HTTPS Settings. . . .
Configuring Bonjour Settings . . .
Configuring the IP Address Filter .
Configuring the Multicast Address
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
53
54
56
56
57
58
60
61
63
64
66
67
68
69
70
72
72
73
6
Configuring Camera Settings. . . . . . . . . . . . . . . . . .
Configuring OSD Settings . . . . . . . . . . . . . . . . . . . . .
Configuring Display Settings . . . . . . . . . . . . . . . . .
Configuring Text Overlay . . . . . . . . . . . . . . . . . . .
Configuring Video Settings . . . . . . . . . . . . . . . . . . . . .
Configuring Snapshot Settings. . . . . . . . . . . . . . . . . . .
Configuring and Handling Alarms . . . . . . . . . . . . . . . . .
Configuring Motion Detection . . . . . . . . . . . . . . . . .
Configuring the Motion Detection Area. . . . . . . . . .
Configuring the Arming Schedule . . . . . . . . . . . .
Configuring the Alarm Actions for Motion Detection . . .
Configuring an External Alarm Input . . . . . . . . . . . . .
Configuring a Video Loss Alarm. . . . . . . . . . . . . . . .
Configuring the Tamper-proof Alarm . . . . . . . . . . . . .
Configuring Exception Handling . . . . . . . . . . . . . . .
Configuring a Privacy Mask . . . . . . . . . . . . . . . . . . . .
Configuring RS-232/RS-485 Port Settings . . . . . . . . . . . . .
Configuring RS-232 Port Settings . . . . . . . . . . . . . . .
Configuring the RS-232 Port as a Transparent Channel .
Configuring RS-485 Port Settings . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
75
75
75
76
77
79
81
81
81
82
83
86
88
89
90
91
93
93
93
94
7
Configuring Recording and Capturing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Configuring Holiday Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Configuring Scheduled Recording and Capturing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
8
Playing Back Recorded Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Playing Back a Specific Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Determining the Type of Recorded Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
9
Managing User Accounts .
Adding a User . . . . . . .
Modifying a User . . . . . .
Deleting a User . . . . . . .
10
Searching Logs, Viewing Device Information, and Maintaining the Encoder . . . . . . . . . . . . 111
Searching Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
www.honeywell.com/security
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . 107
. . . . . . 107
. . . . . . 108
. . . . . . 109
Contents | 7
Viewing Device Information . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . .
Restarting the Encoder . . . . . . . . . .
Restoring Default Settings . . . . . . . . .
Importing or Exporting Configuration Files
Importing Configuration Files. . . . .
Exporting Configuration Files. . . . .
Upgrading the System. . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
112
113
113
113
114
114
115
115
Appendix A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .
The encoder cannot be pinged . . . . . . . . . . . . . . . . . . . . . . . . . . .
The transparent channel has been set, but the encoder still does not receive data
The encoder cannot be added with the software . . . . . . . . . . . . . . . . . .
The encoder cannot control a PTZ camera . . . . . . . . . . . . . . . . . . . . .
Video cannot be viewed through the Web browser . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . . 117
. . . . . . . 117
. . . . . . . 117
. . . . . . . 117
. . . . . . . 118
. . . . . . . 118
Appendix B HVE1(X) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Appendix C HVE4(X) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Appendix D HVE8(X) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
800-15877V1 - A - 10/2013
8 | HVE Encoders User Guide
www.honeywell.com/security
Figures | 9
Figures
1
Figure 2-1
Removing the Cover from an HVE8(X) Encoder . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 2-2
Installing and Securing the HDD in an HVE8(X) Encoder. . . . . . . . . . . . . . . . . . . . . 27
Figure 2-3
Connecting the Data Line and the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 2-4
HVE1(X) Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 2-5
HVE1(X) Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 2-6
HVE4(X) Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 2-7
HVE4(X) Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 2-8
HVE8(X) Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 2-9
HVE8(X) Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 2-10
Alarm Input Connections for an Emerson Alarm . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 2-11
Alarm Input Connections for a Normal Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 2-12
Alarm Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 3-1
IP Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 3-2
Found Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 3-3
Editing Network Parameters in the Modify Network Parameters Window . . . . . . . . . . . . 41
Figure 3-4
Honeywell IP Utility Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 3-5
Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 3-6
Encoder Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 4-1
Live View Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 4-2
Message Confirming Successful Image Capture . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 4-3
RS-485 Port Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 4-4
PTZ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 4-5
Preset List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 4-6
PTZ Linking Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 4-7
Video Parameters Button in the Live View Window . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 4-8
Expanded Video Parameters Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 5-1
Local Configuration Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 5-2
Time Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 5-3
Time Zone Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 5-4
NTP Server Time Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 5-5
Daylight Saving Time Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 5-6
TCP/IP Interface for Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 5-7
DNS Server Configuration
Figure 5-8
Port Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 5-9
DDNS Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
800-15877V1 - A - 10/2013
10 | HVE Encoders User Guide
Figure 5-10
DDNS Settings - IP Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 5-11
DDNS Settings - DynDNS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 5-12
DDNS Settings - PeanutHull Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 5-13
DDNS Settings - HVEDDNS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 5-14
PPPoE Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 5-15
Email Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 5-16
NetHDD Settings Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 5-17
HDD Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 5-18
SNMP Settings Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Figure 5-19
SNMPv3 Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Figure 5-20
QoS Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 5-21
FTP Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Figure 5-22
SOCKS Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Figure 5-23
NAT Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 5-24
HTTPS Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 5-25
Creating a Self-signed Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 5-26
Bonjour Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 5-27
IP Address Filter Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 5-28
Adding an IP Address to the IP Address Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 5-29
Advanced Settings Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 6-1
Display Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 6-2
Camera Name Text Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 6-3
Adjusting the OSD Display Position
Figure 6-4
Copying Settings to Other Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 6-5
Text Overlay Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Figure 6-6
Copying Settings to Other Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Figure 6-7
Video Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Figure 6-8
Copying Settings to Other Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 6-9
Snapshot Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 6-10
Copying Settings to Other Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 6-11
Motion Detection Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 6-12
Arming Schedule Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Figure 6-13
Linkage Method Tab for Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 6-14
Selecting an Alarm Output Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 6-15
Alarm Output Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 6-16
Edit Schedule Time Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Figure 6-17
Selecting a Channel for Motion Event Detection . . . . . . . . . . . . . . . . . . . . . . . . . 86
Figure 6-18
Alarm Input Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 6-19
Linkage Method Tab for Alarm Input Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 6-20
Video Loss Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 6-21
Tamper-proof Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 6-22
Exception Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Figure 6-23
Privacy Mask Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 6-24
RS-232 Serial Port Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Figure 6-25
RS-232 Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
www.honeywell.com/security
Figures | 11
Figure 6-26
RS-485 Serial Port Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Figure 7-1
Holiday Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Figure 7-2
Edit Holiday Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Figure 7-3
Checking the Holiday Settings List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Figure 7-4
Schedule Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Figure 7-5
Edit Schedule Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Figure 7-6
Advanced Recording Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Figure 7-7
Copying the Settings to Other Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Figure 8-1
Playback Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Figure 8-2
Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Figure 8-3
Playing Back Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Figure 8-4
Playback Slidebar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 8-5
Recorded Video Color Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 9-1
User Management Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 9-2
Add User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Figure 9-3
User Account - Modifying a User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 9-4
Modify User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 9-5
Confirmation Message for Deleting a User . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 10-1
Log Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Figure 10-2
Basic Device Information Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . 112
Figure 10-3
Maintenance Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Figure 10-4
Confirmation Message for Rebooting the Encoder . . . . . . . . . . . . . . . . . . . . . . . . 113
Figure 10-5
Restore or Default Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Figure 10-6
Confirmation Message for Restoring or Returning the Encoder to Defaults . . . . . . . . . . . 114
Figure 10-7
Import Configuration File Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Figure 10-8
Remote Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
800-15877V1 - A - 10/2013
12 | HVE Encoders User Guide
www.honeywell.com/security
Tables | 13
Tables
Table 1-1
1
HVE Encoders Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 2-1
Tested Compatible HDDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 2-1
HVE1 Front Panel Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 2-2
HVE1 Rear Panel Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 2-3
HVE4 Front Panel Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 2-4
HVE4 Rear Panel Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 2-5
HVE8 Front Panel Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 2-6
HVE8 Rear Panel Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 3-1
Supported Web Browsers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 3-2
Main Page Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 4-1
Live View Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 4-2
Connections for PTZ Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 4-3
PTZ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 4-4
Video Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 5-1
Configurable Encoder Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 5-2
Port Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 6-1
Customizeable Options for Video Main or Sub Streams . . . . . . . . . . . . . . . . . . . . . . 78
Table 6-2
Default RS-485 Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Table 7-1
Recording and Capturing Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Table 8-1
Playback Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
800-15877V1 - A - 10/2013
14 | HVE Encoders User Guide
www.honeywell.com/security
| 15
Cautions and Warnings
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND•
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
Installation and servicing should be performed only by qualified and experienced technicians to
conform to all local codes and to maintain your warranty.
CAUTION
12 V DC models require the use of CSA Certified/UL
Listed Class 2 power adapters to ensure compliance with electrical
safety standards.
Regulatory Statements
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Note
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
800-15877V1 - A - 10/2013
16 | HVE Encoders User Guide
Canadian Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.
Europe
The manufacturer declares that the equipment supplied is compliant with the essential
requirements of the EMC directive 2004/108/EC, conforming to the requirements of standards
EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950 for electrical equipment
safety.
Waste Electrical and Electronic Equipment (WEEE)
Correct Disposal of this Product (applicable in the European Union and other
European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
Safety Instructions
BEFORE OPERATING OR INSTALLING THE UNIT, READ AND FOLLOW ALL
INSTRUCTIONS.
AFTER INSTALLATION, retain the safety and operating instructions for future
reference
1.
HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.
www.honeywell.com/security
| 17
2.
INSTALLATION
•
Install in accordance with the manufacturer’s instructions.
•
Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
•
Do not install the unit in an extremely hot or humid location, or in a place subject to
dust or mechanical vibration. The unit is not designed to be waterproof. Exposure to
rain or water may damage the unit.
•
Any wall or ceiling mounting of the product should follow the manufacturer’s
instructions and use a mounting kit approved or recommended by the manufacturer.
3.
POWER SOURCES - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
facility, consult your product dealer or local power company.
4.
HEAT - Situate away from items that produce heat or are heat sources such as radiators,
heat registers, stoves, or other products (including amplifiers).
5.
WATER AND MOISTURE - Do not use this unit near water or in an unprotected outdoor
installation, or any area classified as a wet location.
6.
MOUNTING SYSTEM - Use only with a mounting system recommended by the
manufacturer, or sold with the product.
7.
ATTACHMENTS - Do not use attachments not recommended by the product
manufacturer as they may result in the risk of fire, electric shock, or injury to persons.
8.
ACCESSORIES - Only use accessories specified by the manufacturer.
9.
CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
10. SERVICING - Do not attempt to service this unit yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to qualified
service personnel.
11. REPLACEMENT PARTS - When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric
shock or other hazards.
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty period
Honeywell will repair or replace, at its sole option, free of charge, any defective products
returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service at
1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA)
number.
Be sure to have the model number, serial number, and the nature of the problem available for
the technical service representative.
800-15877V1 - A - 10/2013
18 | HVE Encoders User Guide
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to
Honeywell without a clearly identified Return Merchandise Authorization (RMA) number
may be refused.
www.honeywell.com/security
About This Document
This document introduces the HVE series of Audio/Video encoders. It covers how to install and
operate an HVE encoder.
This document is intended for installers and operators.
Overview of Contents
This document contains the following chapters and appendixes:
•
Chapter 1, Introduction, introduces the HVE encoders.
•
Chapter 2, Installing an HVE Encoder, describes the physical installation of an HVE
encoder, including connections, installing a HDD, and descriptions of the front panel and
the back panel.
•
Chapter 3, Connecting to an HVE Encoder via the Internet, describes how to find and
connect to the encoder via an internet search engine.
•
Chapter 4, Viewing Live Video, describes how to view live video, how to capture a picture,
and how to control a PTZ camera.
•
Chapter 5, Configuring the Encoder, describes how to configure the encoder settings,
including IP settings, email settings, UPnP settings, HTTPS settings, and Bonjour settings.
•
Chapter 6, Configuring Camera Settings, describes how to use the encoder to remotely
configure camera settings, including snapshot settings, alarm settings, video settings, and
privacy zones.
•
Chapter 7, Configuring Recording and Capturing Settings, describes how to configure
recording and capturing settings, including schedules.
•
Chapter 8, Playing Back Recorded Video, describes how to play back recorded video.
•
Chapter 9, Managing User Accounts, describes how to manage user accounts.
•
Chapter 10, Searching Logs, Viewing Device Information, and Maintaining the Encoder,
describes how to search logs, view device information, restart or restore the encoder to
factory default settings, import or export configuration files, and upgrade the encoder
system.
•
Index, provides a searchable list for easy access to the document.
800-15877V1 - A - 10/2013
20 | HVE Encoders User Guide
Typographical Conventions
This document uses the following typographical conventions:
Font
What it represents
Example
Helvetica
Keys on the keyboard
Press Ctrl+C
Lucida
Values of editable fields that are mentioned in the
The Time from field can be set to
body text of the document for reference purposes,
Hours:Minute:Seconds.
but do not need to be entered as part of a procedure
Text strings displayed on the screen
The message Unauthorized displays.
Syntax
(object) entered
Swiss721 BT Bold Words or characters that you must type. The word
“enter” is used if you must type text and then press
the Enter or Return key.
Italic
Enter the password.
Menu titles and other items you select
Double-click Open from the File menu.
Buttons you click to perform actions
Click Exit to close the program.
Placeholders: words that vary depending on the
situation
Enter your user name.
Cross-reference to external source
Refer to the System Administrator Guide.
Cross-reference within document
See Chapter 2, Installation.
www.honeywell.com/security
1
Introduction
1
Incorporating the latest in encoding technology, the HVE(X) series of Audio/Video encoders
digitizes analog video, and then can store that video on a Hard Disk Drive (HDD) or SATA drive,
or transmit that video over the internet.
Using the latest embedded processor, the HVE(X) Series Audio/Video encoders provide:
•
More powerful capabilities in audio/video encoding
•
More data storage via microSD (HVE1, HVE1X, HVE4, HVE4X) or HDD (HVE8, HVE8X)
•
More support for various network protocols
•
More stability and reliability because the code is downloaded in FLASH
Table 1-1
HVE Encoders Model Numbers
Model number
Description
HVE1
1-channel, Audio/Video Encoder, microSD compatible, NTSC
HVE1X
1-channel, Audio/Video Encoder, microSD compatible, PAL
HVE4
4-channel, Audio/Video Encoder, microSD compatible, NTSC
HVE4X
4-channel, Audio/Video Encoder, microSD compatible, PAL
HVE8
8-channel, Audio/Video Encoder, SATA HDD compatible, NTSC
HVE8X
8-channel, Audio/Video Encoder, SATA HDD compatible, PAL
800-15877V1 - A - 10/2013
22 | HVE Encoders User Guide
Features
Encoding Features
•
H.264/MPEG4/MPEG2/MJPEG encoding
•
Encoding up to 4CIF resolution
•
Dual-stream encoding
•
Either compound stream encoding or video stream encoding (with audio and video
synchronization during compound stream encoding)
Network Features
•
One 10M/100Mbps adaptive Ethernet interface (PoE) for HVE1(X)/HVE4(X) models
•
One 10M/100M/1000Mbps adaptive Ethernet interface for HVE8(X) models
•
Multiple browser support: IE, FireFox, Chrome, and Safari
•
Remote web browser access by HTTPS ensures high security
•
Netfilter builds internet firewalls based on packet filtering
•
QoS protocol enhances data transmission performance
•
Support for SNMPv1/v2c/v3 simple network management protocol
•
mDNS-based Apple’s Bonjour protocol enables automatic device discovery
•
Supports email notifications, FTP uploading, and alarm uploading by SOCKS v4/v5 proxy
server
•
Zero configuration networking (Zeroconfig) enables the device to automatically obtain the
IPv4 link-local IP addresses (range: 169.254.1.0 to 169.254.254.255)
•
Auto/manual port mapping by UPnP™
•
Supports PSIA and ONVIF protocols
•
Supports Honeywell IP Utility ver 1.53 for automatically searching and discovering the
online devices in the local network area
•
Automatically acquires IP addresses through the DHCP protocol
•
Supports RTSP/RTP standard stream media protocol, which allows users to view live
video through unicast
•
Supports multicast addresses for live viewing of multiple cameras through the network
•
Supports two-way audio and single-direction broadcasting
•
Supports transmission via RS-232 and RS-485 transparent channels (except
HVE1/HVE1X)
•
Supports access to the internet through PPPoE, and supports Peanut Hull, DynDNS, and
HVEDDNS
•
Supports NTP for setting the time
•
Connectible with a network HDD in NAS and IPSAN mode
www.honeywell.com/security
Introduction | 23
•
Supports sending emails by SMTP protocol, and supports attaching captured JPEG
images and SSL encryption
•
Supports remote JPEG image capturing with user-defined image resolution and quality
•
Supports multiple PTZ protocols - Channels can be configured for:
PTZ
•
Protocol type
•
RS-485 address
•
Baud rate
•
Data bit
•
Stop bit
•
Even and odd parity
•
Stream control method
•
Remote configuration for presets, patrols, and patterns
•
Supports PTZ linkage configuration to link relay alarm inputs with the callup of predefined
presets, patrols, and patterns
•
Supports Relay Alarm Input
Alarm
•
•
Configurable to either Normally Open (NO) mode or Normally Closed (NC) mode
•
Select from up to four different alarm arming periods
•
Supports triggering the corresponding alarm handling methods, relay alarm output,
buzzer alarm, upload to control center, PTZ linkage, presets/patrols/pattern callup.
Supports Relay Alarm Output
•
Connect relay alarm output with alarm devices for alarm handling within an arming
period.
Exceptions
•
•
Supports Exception Alarm Handling
•
Exception alarms include network disconnect alarm, IP address conflict alarm, and
illegal access alarm.
•
Supports multiple alarm handling methods, relay alarm output, buzzer alarm, and
uploading to a center.
Supports Exception Reboot
•
Software Watchdog –Inspects important device threads and system resources.
Automatically reboots the device if an exception is detected.
•
Firmware Watchdog –Inspects the device firmware. Automatically reboots the device
if an exception in system task scheduling is detected.
800-15877V1 - A - 10/2013
24 | HVE Encoders User Guide
Logs
Supports log classification into operation logs, alarm logs, exception logs, and information logs.
Users can search and view all recorded system logs by date or type, as well as export the logs
to text format over the network.
Note
www.honeywell.com/security
A hard disk/network disk/microSD card must be connected before log operation.
2
Installing an HVE Encoder
2
This chapter explains:
•
Encoder installation and connections
•
HDD installation [HVE8(X) only]
•
Encoder front and back panels
•
Alarm connections
Installation
The HVE1(X)/HVE4(X)/HVE8(X) encoders are highly advanced surveillance equipment that
should be installed with care. If your encoder supports a HDD, then please ensure that you
install a manufacturer-recommended HDD. See Table 2-1 for a list of recommended HDDs.
During encoder installation:
•
Use brackets for rack mounting.
•
Ensure that there is ample room for audio and video cables.
•
When installing the cables, ensure that the bend radius of the cables is no less than five
times its diameter.
•
Connect both the alarm and the RS-485 cable.
•
Allow at least 2cm (~0.75 inch) of space between rack-mounted devices.
•
Ensure that the encoder is grounded.
•
Ensure that the environmental temperature is within -10°C–55°C (14°F–131°F).
•
Ensure that the environmental humidity is within 10%–90%.
Installing the Hard Disk Drive (HDD) [HVE8(X) only]
This section applies only to HVE8(X) models, which have room for a Hard Disk Drive (HDD) for
recording.
800-15877V1 - A - 10/2013
26 | HVE Encoders User Guide
Preparing for Installation
Your HVE8(X)encoder comes from the factory without a HDD. Follow these instructions to install
a HDD that is appropriate for your situation according to the total capacity, which is calculated
in terms of the Schedule Recording Settings (please see Configuring Scheduled Recording and
Capturing on page 99). The installation and removal of the hard disk should be done by qualified
professionals.
Before installing a HDD, please ensure the power is disconnected from the device. Only a
factory-recommended HDD should be used for this installation.
Table 2-1
Tested Compatible HDDs
SEAGATE
Capacity
HDD Model
3T
ST3000VX000-9YW1
ST2000VX000-9YW1
2T
ST2000VX002-1AH1
ST2000VM003-1CT1
ST1000VM002-9ZL1
1T
ST31000322CS
ST1000VX000-9YW1
ST31000526SV
500G
ST3500410SV
ST3500411SV
ST3250312CS
250G
ST3250310SV
ST3250820SV
WD
Required Tools:
Capacity
HDD Model
2T
WD20EURS-63S
1T
WDC WD10EVDS-63U
Screwdriver
Installing the HDD
1.
Use the screwdriver to unfasten the screws on both sides and the rear panel of the
encoder, then remove the cover from the chassis and set aside.
www.honeywell.com/security
Installing an HVE Encoder | 27
Figure 2-1
2.
Removing the Cover from an HVE8(X) Encoder
Place the HDD into the slot on the chassis, and then secure it in position by tightening the
screws at the bottom of the chassis.
Figure 2-2
Installing and Securing the HDD in an HVE8(X) Encoder
Install
Secure
3.
Remove the HDD data line from the accessories box. Plug one end of the data line to the
circuit board, and the other end to the data line port on the HDD. Connect the power cord
to the HDD in the same way.
Figure 2-3
Connect the data line
4.
Connecting the Data Line and the Power Cord
Connect the power cord
Replace the chassis cover, and then tighten the screws on both sides and the rear panel of
the encoder.
800-15877V1 - A - 10/2013
28 | HVE Encoders User Guide
HVE1/HVE1X Encoder Front and Rear Panels
Figure 2-4
Table 2-1
1
HVE1(X) Front Panel
HVE1 Front Panel Elements
Interface Element
Function
PWR LED Indicator
Lights red when the device is powered on.
Lights orange when a microSD card is inserted.
2
VIDEO IN
BNC connector for video input.
3
LINE IN
3.5mm connector for two-way audio input. Connect to an audio input
device or an active pick-up, a microphone, etc.
4
AUDIO OUT
3.5mm connector for audio output. Connect to an audio output device,
such as a loudspeaker.
5
microSD
microSD interface for data storage up to 32 GB, Class 6 and above.
6
RESET
Restore to the factory default settings by holding the RESET button for
more than 15 seconds after the power is turned on.
www.honeywell.com/security
Installing an HVE Encoder | 29
Figure 2-5
Table 2-2
1
HVE1(X) Rear Panel
HVE1 Rear Panel Elements
Interface Element
Function
ALARM IN/OUT
Relay alarm input/output. The maximum voltage/current supported
by the relay output is 12 V / 1 A.
Note The alarm output terminal provides no JP2 pin.
2
RS-485
RS-485 connection for pan, tilt, zoom control.
3
LAN
10M/100Mbps adaptive Ethernet interface (PoE).
The right LED indicator lights green when the network cable is
connected. The left LED indicator blinks orange when receiving or
transmitting data.
4
DC 12 V
12 V DC power supply
5
GND
Ground
Note
The HVE1(X) model encoder does not support/supply a beeper/audio alert.
800-15877V1 - A - 10/2013
30 | HVE Encoders User Guide
HVE4/HVE4X Encoder Front and Rear Panels
Figure 2-6
Table 2-3
1
HVE4(X) Front Panel
HVE4 Front Panel Elements
Interface Element
Function
PWR LED Indicator
Lights red when the device is powered on.
Lights orange when a microSD card is inserted.
2
LINE IN
3.5mm connector for a two-way audio input. Connect to an audio input
device or an active pick-up, a microphone, etc.
3
AUDIO OUT
3.5mm connector for audio output. Connect to an audio output device,
such as a loudspeaker.
4
VIDEO IN
BNC connectors for video input.
5
AUDIO IN
Inputs for audio.
www.honeywell.com/security
Installing an HVE Encoder | 31
Figure 2-7
Table 2-4
HVE4(X) Rear Panel
HVE4 Rear Panel Elements
Interface Element
Function
1
ALARM IN
Relay alarm input.
2
ALARM OUT
Relay alarm output. The maximum voltage/current supported by the
relay output is 12 V / 1 A.
3
RS-232
Serial interface for configuring the encoder’s parameters, or for using
as a transparent channel. See Configuring the RS-232 Port as a
Transparent Channel on page 93.
4
RS-485
RS-485 connection for pan, tilt, zoom control.
5
RESET
Restore to the factory default settings by holding the RESET button
for more than 15 seconds after the power is turned on.
6
microSD
microSD interface for data storage up to 32 GB, Class 6 and above.
7
LAN
10M/100Mbps adaptive Ethernet interface (PoE).
The right LED indicator lights green when the network cable is
connected. The left LED indicator blinks orange when receiving or
transmitting data.
8
DC 12 V
12 V DC power supply
9
GND
Ground
Note
The HVE4(X) model encoder does not support/supply a beeper/audio alert.
800-15877V1 - A - 10/2013
32 | HVE Encoders User Guide
HVE8/HVE8X Encoder Front and Rear Panels
Figure 2-8
Table 2-5
HVE8(X) Front Panel
HVE8 Front Panel Elements
Interface Element
Function
1
POWER
Lights red when the device is powered on.
2
STATUS
Lights red when reading data from or writing data to the HDD.
3
Tx/Rx
Does not light when the encoder is not connected to the network.
Blinks green when receiving or transmitting data.
Blinks at a higher frequency when receiving or transmitting large
amounts of data.
Figure 2-9
Table 2-6
HVE8(X) Rear Panel
HVE8 Rear Panel Elements
Interface Element
Function
1
VIDEO IN
BNC connectors for video input.
2
LINE IN
3.5mm connector for two-way audio input. Connect to an audio input
device or an active pick-up, a microphone, etc.
3
AUDIO OUT
3.5mm connector for audio output. Connect an audio output device,
such as a loudspeaker.
4
AUDIO IN
Inputs for audio.
www.honeywell.com/security
Installing an HVE Encoder | 33
Table 2-6
5
HVE8 Rear Panel Elements
Interface Element
Function
LAN
10/100/1000 Mbps adaptive Ethernet interface.
The right LED indicator lights green when the network cable is
connected. The left LED indicator blinks orange when data is
transmitting/receiving.
6
RESET
Restore to the factory default settings by holding the RESET button
for more than 15 seconds after the power is turned on.
7
RS-232, RS-485
Serial interface for configuring the encoder’s parameters, or for using
as a transparent channel. See Configuring the RS-232 Port as a
Transparent Channel on page 93.
RS-485 connection for pan, tilt, zoom control.
8
ALARM IN
Relay alarm inputs.
9
ALARM OUT
Relay alarm outputs.
10
DC 12 V
12 V DC power supply
11
GND
Ground
Connecting Alarms
Connecting Alarm Inputs
HVE encoders support open/close relay inputs for alarms. For the alarm input signal not in
open/close relay signal mode, please connect as shown in the following diagrams.
Alarm Input Connections for an Emerson Alarm
Figure 2-10
Alarm Input Connections for an Emerson Alarm
100ȍ
10 V regulator
Emerson
Alarm
ALM (+)
V-output
Encoder
10 V regulator
ALM (-)
4N35
optocoupler
IN(n)
G
Relay Input
800-15877V1 - A - 10/2013
34 | HVE Encoders User Guide
Note
The relay input port on the encoder should be set to NC mode.
Alarm Input Connections for a Normal Alarm
Figure 2-11
Alarm Input Connections for a Normal Alarm
JQC-3FG
24 V Relay
Encoder
Alarm
ALM (+)
V-output
IN(n)
ALM (-)
G
Relay Input
Connecting Alarm Outputs
HVE encoders support open/close relay inputs for the alarm output mode. Alarm inputs can be
configured as NO or NC. AC and DC loads are different, so different alarm output connection
methods are used for each. For alarm output connections, please connect as shown in the
following diagram.
Figure 2-12
Alarm Output Connections
OUT1
OUT1
+
DC -
AC
G
G
JJ1
JJ1
Note
The HVE1(X) has no JJ1 relay.
Please note the different connections for JJ1 show in Figure 2-12.
www.honeywell.com/security
Installing an HVE Encoder | 35
For the DC load, JJ1 can be safely used both in NC or NO modes. It is recommended that you
use within the limit of 12 V / 1 A. For external AC input, the JJ1 relay must be open. The
motherboard provides two jumpers, which each correspond to an alarm output. These jumpers
are factory set to be connected.
800-15877V1 - A - 10/2013
36 | HVE Encoders User Guide
www.honeywell.com/security
3
Connecting to an HVE Encoder via the
Internet
3
The encoder can also be accessed through a Web browser for configuration and operation. You
can use:
•
Microsoft Internet Explorer 6/7/8/9
•
Mozilla Firefox 3.5 and above
•
Google Chrome 8 and above
•
Apple Safari 5.0.2 and above
Windows XPSP1 and above (32-bit) is required.
Before you can access the encoder through the internet, you must configure the encoder’s
network settings. See Configuring Network Parameters on page 39.
Before you start:
•
Connect the device to the LAN, and prepare a PC that is connected to the same LAN with
the device.
•
Know the following:
•
Factory default device user name: admin
•
Factory default device password: 1234
•
Factory default device IP address: 192.168.0.250
Installing the IP Utility
Note
Before installing the Honeywell IP Utility, ensure that your encoder is connected
to your network through a CAT5 Ethernet cable.
800-15877V1 - A - 10/2013
38 | HVE Encoders User Guide
Note
We recommend that you disable any Norton’s AntiVirus software that might be
running on your workstation.
To discover the IP device and configure the network settings, you must first install the IP Utility.
For more information, see the user guide on the software CD that came with your encoder, or
go to www.honeywell.com/security.
Note
You must have Windows administrator privileges for the workstation onto which
the Honeywell IP Utility is being installed.
1.
Insert the software CD. Autorun will start the installation. If autorun does not start, browse
to the CD drive, and run Honeywell IP Utility Setup.exe.
2.
Follow the steps in the InstallShield wizard.
3.
Log on to the IP Utility by double-clicking the IP Utility icon (
main IP Utility page appears.
Figure 3-1
www.honeywell.com/security
IP Utility
) on the desktop. The
Connecting to an HVE Encoder via the Internet | 39
Configuring Network Parameters
If you do not know the IP address of the encoder, and this is not the first time you are using the
encoder, then you can use SADP (IP finder) software or the Serial port tools to find the encoder’s
IP address, and to configure the IP address or other network parameters. We recommend that
you change the default IP address for the first use.
Note
For the first-time user, the default user name is admin, and the default password
is 1234. The default IP address is 192.168.0.250.
Searching for Online Devices
Automatically Searching for Online Devices
After you log on to the IP Utility, the devices on the network are automatically discovered and
listed in the Discovery pane. After the initial discovery, auto-refresh continues to discover newly
added network devices.
800-15877V1 - A - 10/2013
40 | HVE Encoders User Guide
Figure 3-2
Note
Found Devices
Found devices will automatically appear 15 seconds after they go online. They
will disappear from the list 45 seconds after they go offline.
Manually Searching for Online Devices
Click the Refresh button
to manually refresh the Online Device list. The newly discovered
devices will be added to the list.
Note
www.honeywell.com/security
You can click Up or Down buttons on each column heading to reorder the
information. Click >> to expand the device table, and to hide the network
parameter panel on the right side. Click << to show the network parameter
panel.
Connecting to an HVE Encoder via the Internet | 41
Modifying Network Parameters
1.
Click to select a connected device in the device list. The network parameters for the
selected device appear in the IP Network Settings panel on the right side.
2.
Configure the network settings.
•
Automatically – Click to select Obtain an IP Address automatically, enter the
Device Name, then click Apply. The network settings are automatically assigned
from the network server.
•
Manually – Click to deselect Obtain an IP Address automatically, then enter the
Device Name, IP Address, Subnet Mask, and Gateway. Then click Apply.
Figure 3-3
Editing Network Parameters in the Modify Network Parameters Window
Note
Check the IP network settings before clicking Apply. Incorrect values might
cause a failure when connecting the tool to the encoder.
Note
Contact your network administrator if you have any network-related issues or
questions about your network.
800-15877V1 - A - 10/2013
42 | HVE Encoders User Guide
Connecting to an Online IP Device
1.
Connect to your IP device by double-clicking it in the Discovery pane, or by selecting it
and clicking
.
The name for the connected device turns bold and blue, and the Launch Browser button
becomes active.
2.
Click Launch Browser. The Honeywell IP Utility login window opens.
Figure 3-4
Honeywell IP Utility Window
Accessing an HVE Encoder Through a Web Browser
HVE encoders can be accessed through a Web browser for configuration and operation.
Table 3-1
Supported Web Browsers
Microsoft Internet Explorer 6, 7, 8, 9
Mozilla Firefox 3.5 and above
Google Chrome 8 and above
Apple Safari 5.0.2 and above
Windows XP SP1 and above (32-bit)
1.
Open the web browser.
2.
Enter the encoder’s IP address (default: 192.168.0.250), and then press Enter on your
keyboard.
The login window appears.
www.honeywell.com/security
Connecting to an HVE Encoder via the Internet | 43
Figure 3-5
Note
Login Window
When the HTTPS feature is enabled, the system uses the HTTPS login mode
(https://192.168.0.250) by default when you enter the IP address. You can also
enter http://IP address/index.asp (for example, http://192.168.0.250/index.asp)
if you want to use the HTTP mode to log into the device.
3.
Enter the user name (default: admin) and password (default: 1234) to log into the system.
The main page appears.
4.
Download and install the plug-in from the main page. Follow the prompts.
Note
After initial log in and plug-in installation, you will automatically enter the main
page after logging in. [?]
When you have successfully downloaded and installed the plug-in, the encoder main page
appears.
800-15877V1 - A - 10/2013
44 | HVE Encoders User Guide
Figure 3-6
Table 3-2
Encoder Main Page
Main Page Elements
Element
Description
Menu Bar
Click to choose Live View, Playback, Log, Configuration.
Device List
Displays the connected encoder and its channels.
Window division
Select from 1-, 4-, and 8-channel view.
Live Video Window
Displays live video from the chosen camera.
Toolbar
Select actions while live viewing, such as live view, image
capture, recording, turn audio on/off, etc.
PTZ Control
Control PTZ cameras, including camera lights and camera wiper.
Preset Setting/Calling
Set and recall presets for PTZ cameras.
Video Parameters Settings
Configure live video brightness, contrast, hue, and saturation.
www.honeywell.com/security
4
Viewing Live Video
4
When connected, Live View shows real-time video for the connected camera.
Note
After your first successful login, the system will automatically enter the Live View
page.
Starting Live View
1.
Click to select a window for viewing live video.
Figure 4-1
Live View Window
Click to select
800-15877V1 - A - 10/2013
46 | HVE Encoders User Guide
2.
Double-click a camera
in the device list to start live view.
Starting Live View for All Cameras
Click
on the lower toolbar to start live view of all cameras on the device list.
Live View Toolbar
Table 4-1
Icon
Live View Toolbar
Function
Select the window division mode for display.
Start Live View.
Stop Live View.
Capture an image in Live View.
Manually start recording video.
Manually stop recording video.
Start PTZ control (must be supported by a PTZ camera).
Previous Page.
Next Page.
Turn audio On.
Turn audio Off.
Start two-way audio.
Stop two-way audio.
Note
Before you can use two-way audio or can record with audio, you must select
Video & Audio for the Stream Type. See Video Type in Table 6-1 on page 78.
Full Screen Mode
Double-click on a live video window to view that video in the full-screen mode. Double-click
again to return to normal mode.
www.honeywell.com/security
Viewing Live Video | 47
Capturing an Image
In Live View, click
in the toolbar to capture a live image.
When you have successfully captured an image, a message appears.
Figure 4-2
Message Confirming Successful Image Capture
Configuring the Save Path for Captured Images
To configure the saving path for captured images, go to Configuration  Local Configuration.
See Figure 5-1, Local Configuration Window, on page 53.
Note
The captured image is saved as a JPEG.
Controlling a PTZ Camera
In Live View mode, you can use your encoder to control a PTZ camera. Using your mouse, you
can click any of the 8 directional buttons in the display window to control a PTZ camera.
Before you begin controlling a PTZ camera, ensure that the following conditions are met:
•
The connected camera supports PTZ control.
•
The baud rate, PTZ control, and address on the encoder are configured the same as on
the connected PTZ camera.
800-15877V1 - A - 10/2013
48 | HVE Encoders User Guide
Connecting to a PTZ Camera
Connect the R+ and R- terminals of the pan/tilt/zoom unit to the RS-485 D+ and the RS-485 Dterminals of the encoder.
Table 4-2
Connections for PTZ Cameras
On the camera, connect the
To the ...on the encoder
R+ terminal
RS-485 D+ terminal
R- terminal
RS-485 D- terminal
Configuring for a PTZ Camera
1.
Go to Remote Configuration  Serial Port Settings  485 Serial Port.
2.
Ensure that the baud rate, PTZ control, and address on the encoder are configured the
same as on the connected PTZ camera. See Figure 4-3.
Figure 4-3
Note
RS-485 Port Settings
The default for Diamond PTZ protocol is Even parity.
Controlling a PTZ Camera
In Live View mode, you can use the PTZ control buttons to control a PTZ camera.
www.honeywell.com/security
Viewing Live Video | 49
Figure 4-4
PTZ Controls
Table 4-3
PTZ Controls
Button
Function
Zoom in (+) and out (-).
Focus near (+) and far (-).
Iris open (+) and close (-).
Click to turn on/off a light (available if the connected PTZ
camera supports a light/has an external light).
Click to turn on/off the wiper (available when the connected
PTZ camera supports a wiper function).
Slide the bar to set the PTZ speed from level 1 to 7.
Setting and Calling Presets
1.
Select a preset number from the Preset list.
Figure 4-5
2.
3.
Preset List
Use the PTZ controls to move the PTZ camera’s field of view to the desired position. You
can:
•
Pan the camera to the left or right.
•
Tilt the camera up or down.
•
Zoom in or out.
•
Refocus the lens.
Click
to save the current camera position.
800-15877V1 - A - 10/2013
50 | HVE Encoders User Guide
Note
Up to 256 presets can be configured, depending on the applied PTZ protocol.
Calling a Preset
This feature allows you to instantly position the camera to a preset scene (camera lens
orientation, focus, and zoom) when an event occurs.
You can recall pre-defined presets at any time.
In Live View mode, select a predefined preset from the list, then click
.
Linking a Preset to an Alarm
The preset can also be used to link to the alarm input when an alarm event occurs.
To link a preset to an alarm, configure as shown in Figure 4-6.
Figure 4-6
PTZ Linking Configuration
For more information about configuring PTZ linkage settings, please see Configuring RS-485
Settings on page 93.
Configuring Video Parameters
You can configure the video parameters, including the brightness, contrast, saturation, and hue.
1.
Click
www.honeywell.com/security
in the bottom right corner of the Live View window.
Viewing Live Video | 51
Figure 4-7
Video Parameters Button in the Live View Window
The Video parameters menu expands.
Figure 4-8
2.
Expanded Video Parameters Menu
Select the video mode appropriate for the lighting condition.
Table 4-4
Video Modes
Mode
Description
Standard
Suitable for general lighting conditions. (default setting)
Indoor
The image is relatively smoother.
Outdoor
The image is relatively clearer and sharper. Contrast and
saturation are high.
Dim Light
The image is smoother than the other three modes.
800-15877V1 - A - 10/2013
52 | HVE Encoders User Guide
3.
Move the slider to set the brightness, contrast, saturation and hue from 0—255. The
default value is 128 for the brightness, contrast, and hue, and is 136 for saturation.
4.
Move the slider to set the sharpness from 0—15, and the denoising level to 0—3. The
default value is 3 for the sharpness and 1 for the denoising level.
Note
www.honeywell.com/security
Click
to restore to the default settings.
5
Configuring the Encoder
1.
Click Configuration  Local Configuration to enter the Local Configuration window.
Figure 5-1
2.
5
Local Configuration Window
Configure the settings. Click Browse to change the directories for saving video files and
pictures.
Table 5-1
Configurable Encoder Settings
Setting
Description
Protocol Type
Select the protocol type for stream transmission.
UDP: Provides more real-time audio and video streams.
TCP: Ensures complete delivery of streaming data and better
video quality. However, real-time video quality is reduced.
Stream Type
Select Main or Sub stream type for Live View for the Web browser.
See Configuring Video Settings on page 77 for the parameter
settings for the Main and Sub streams.
Image Size
Select the window division.
Record File Size
Select the size of packed video files during manual recording.
Select from 256MB, 512MB, or 1GB.
800-15877V1 - A - 10/2013
54 | HVE Encoders User Guide
Table 5-1
Configurable Encoder Settings
Setting
Description
Live View
Performance
Choose the way that live video is displayed. Select from Least
Delay, Balanced (delay and fluency), or Best Fluency.
Save recorded files
to
Set the saving path for the manually recorded video files.
Save snapshots in
live view to
Set the saving path for the manually captured pictures in live view
mode.
Save snapshots
Set the saving path for the pictures captured in playback mode.
when in playback to
Save clips to
Set the saving path for the video files clipped in playback mode.
Save downloaded
files to
Set the saving path for the downloaded video files or pictures.
Configuring Time Settings
1.
Click Remote Configuration  Device Parameters  Time Settings to enter the Time
Settings interface.
Figure 5-2
www.honeywell.com/security
Time Settings Interface
Configuring the Encoder | 55
2.
Select the Time Zone. From the drop-down menu, select the Time Zone that is closest to
the device’s location.
Figure 5-3
3.
Time Zone Selection
Select the time synchronization. Select from either NTP or Manual Time Sync.
NTP: Selecting NTP means that a Network Time Protocol (NTP) Server, which you have
configured, will be used to ensure the accuracy of your encoder’s date and time.
If the encoder is connected to a Dynamic Host Configuration Protocol (DHCP) network
that has time properties that are configured, then the encoder automatically synchronizes
with the time server.
Manual Time Sync: Selecting Manual Time Sync means that you configure the date and
time in the Set Time field. You have the option of clicking Sync. with computer time to
synchronize the encoder time with the time of the local PC.
Configuring NTP Time Sync by NTP Server
a.
Click to enable NTP.
Figure 5-4
NTP Server Time Synchronization
b.
Enter the NTP server IP address.
c.
Enter the NTP port.
d.
Select an interval for the time between the two NTP server synchronizing actions.
Select from 1 to 10080 minutes.
Configuring the Time and Date Manually
a.
Click to enable Manual Time Sync.
b.
Click
c.
Select the date and time from the popup calendar. Click
to open the pop-up calendar used for setting the date and time.
to quickly set the time.
800-15877V1 - A - 10/2013
56 | HVE Encoders User Guide
4.
Configure the Daylight Saving Time (DST) settings.
a.
Click to enable DST.
Figure 5-5
b.
5.
Daylight Saving Time Settings
Select the Start Time and End Time for the DST period, then select a DST Bias
period.
Click Save to save the new settings.
Configuring Network Settings
Configuring TCP/IP Settings
Network settings must be properly configured before you can operate the encoder over a
network.
1.
Click Remote Configuration  Network Settings  TCP/IP to enter the TCP/IP settings
interface.
Figure 5-6
2.
TCP/IP Interface for Network Settings
Configure the NIC settings, including the NIC Type, IPv4 Address, IPv4 Subnet Mask, IPv4
Default Gateway, and MTU settings.
www.honeywell.com/security
Configuring the Encoder | 57
Note
The MTU range is only from 500 to 1500.
3.
If the DHCP server is available, then click the DHCP checkbox to automatically obtain an
IP address and other network settings from that server.
4.
If the DNS server settings are required for some applications (for example, for sending
email), then carefully configure the Preferred DNS Server and Alternate DNS Sever.
Figure 5-7
5.
DNS Server Configuration
Click Save to save the new settings.
Configuring Port Settings
You can set the encoder’s ports, including the HTTP port, RTSP port, and HTTPS port.
1.
Click Remote Configuration  Network Settings  Port to enter the Port settings
interface.
Figure 5-8
2.
Enter the values for each port.
Table 5-2
3.
Port Settings Interface
Port Defaults
Port
Default
HTTP
80
RTSP
554
HTTPS
443
Click Save to save these new settings.
800-15877V1 - A - 10/2013
58 | HVE Encoders User Guide
Note
You will be asked to reboot the encoder to activate these new settings.
Configuring DDNS Settings
If your encoder is set to use PPPoE as its default network connection, then you might set
Dynamic DNS (DDNS) to be used for network access.
Note
1.
Prior registration with your DDNS provider is required before configuring the
system to use DDNS.
Click Remote Configuration  Network Settings  DDNS Settings to enter the DDNS
settings interface.
Figure 5-9
DDNS Interface
2.
Click the Enable DDNS checkbox.
3.
Select the DDNS Type from the drop-down menu. Select from IPServer, DynDNS,
PeanutHull, and HVEDDNS.
IPServer
a.
Select IPSever from the DDNS Type drop-down menu.
b.
Enter a Server Address.
Figure 5-10
c.
www.honeywell.com/security
DDNS Settings - IP Server Settings
Click Save to save the new settings.
Configuring the Encoder | 59
Note
For the IP Server, you have to apply a static IP, subnet mask, gateway, and
primary DNS from the ISP. The Server IP should be entered with the static IP
address of the PC that runs the IPServer software.
DynDNS
a.
Select DynDNS from the DDNS Type drop-down menu.
Figure 5-11
DDNS Settings - DynDNS Settings
b.
Enter a Server Address for DynDNS (for example, members.dyndns.org).
c.
Enter the domain that is obtained from the DynDNS website in the Device Domain
Name text field.
d.
Enter the User Name and Password that is registered on the DynDNS website.
Confirm the password.
e.
Click Save to save the new settings.
PeanutHull
a.
Select PeanutHull from the DDNS Type drop-down menu.
Figure 5-12
b.
DDNS Settings - PeanutHull Settings
Enter the User Name and Password that is given by the PeanutHull website.
800-15877V1 - A - 10/2013
60 | HVE Encoders User Guide
c.
Click Save to save the new settings.
HVEDDNS
a.
Select HVEDDNS from the DDNS Type drop-down menu.
Figure 5-13
b.
DDNS Settings - HVEDDNS Settings
Enter the encoder’s Domain name.
•
You can register the alias for the encoder’s device name in the HVEDDNS server
first, and then enter the domain name’s alias in the encoder.
OR
•
Note
c.
Enter the domain name directly in the encoder to create a new one.
If a new alias for the device’s domain name is defined in the encoder, it will
replace the old one that is registered on the server.
Click Save to save the new settings.
Configuring PPPoE Settings
Your encoder also allows access by Point-to-Point Protocol over Ethernet (PPPoE).
1.
Click Remote Configuration  Network Settings  PPPoE Settings to enter the
PPPoE settings interface.
www.honeywell.com/security
Configuring the Encoder | 61
Figure 5-14
PPPoE Settings Interface
2.
Check the PPPoE checkbox.
3.
Enter a User Name, Password, and Confirm Password for PPPoE access.
Note
4.
The User Name and Password should be assigned by your ISP.
Click Save to save these new settings and exit the PPPoE Settings interface.
Configuring Email Settings
The encoder can be configured to send alarm event-triggered email notifications to all
designated receivers. The types of triggering events can include motion detection, video loss,
and tampering.
Before configuring email settings, ensure that the following conditions are met:
•
The encoder is connected to a local area network (LAN) that maintains an SMTP mail
server. The network must also be connected to either an intranet or to the Internet,
depending on the location of the email accounts to which you want to send notifications.
•
You have configured the DNS server settings under Remote Configuration  Network
Settings  TCP/IP before using the email function. See Configuring TCP/IP Settings on
page 56.
To configure email settings:
1.
Enter the basic network settings (Remote Configuration  Network Settings  TCP/IP)
to set the IPv4 address, IPv4 Subnet Mask, IPv4 Default Gateway, and the preferred DNS
Server.
2.
Click Remote Configuration  Network Settings  Email to enter the Email settings
interface.
800-15877V1 - A - 10/2013
62 | HVE Encoders User Guide
Figure 5-15
3.
4.
Email Settings Interface
Configure the following:
Configurable Field
Description
Authentication
Optional. If your email server requires authentication, check this checkbox
to use authentication to log in to this server, and enter the login User
Name and Password.
SMTP Server
The SMTP server IP address of the host name (for example,
smtp.263xmail.com)
SMTP Port
The SMTP port. The default TCP/IP port used for SMTP is 25.
Enable SSL
Click the checkbox to enable SSL if required by the SMTP server. When
the SSL is enabled, the default TCP/IP port used for SMTP is 465.
Interval
The interval refers to the time between two actions of sending attached
pictures.
Attach Image
Check if you want to send email with attached alarm images.
Sender
The sender’s name.
Sender’s Address
The sender’s address.
Choose Receiver
Select the receiver to which the Email is sent. Up to 3 receivers can be
configured.
Receiver
The name of the user to be notified.
Receiver’s Address
The address of the user to be notified.
Click Save to save these new settings.
For more information about email notifications, please see the following sections:
•
Configuring Motion Detection on page 81
•
Configuring External Alarm Input on page 86
•
Configuring a Video Loss Alarm on page 88
•
Configuring the Tamper-proof Alarm on page 89
•
Configuring Exception Handling on page 90
www.honeywell.com/security
Configuring the Encoder | 63
Adding the Network Disk
You should add the network disk before recording, playing back video, or searching the log.
Before adding the network disk, ensure that the following conditions are met:
•
The network storage device is available within the network and is properly connected.
•
The network storage device is configured with NAS or IP SAN mode (please refer to the
User Manual for the IP SAN/NAS).
To add a network disk:
1.
Click Remote Configuration  Network Settings  NetHDD to enter the NetHDD
settings interface.
Figure 5-16
NetHDD Settings Interface
2.
Enter the Network Storage System IP address and the File Path in the correct fields.
3.
Select the type of Network Storage System, either IP SAN or NAS.
NAS Mode: Enter the storage device’s IP address. The default file path is /dvr/share, in
which the share name is user-defined when creating the DVR of the network storage.
IP SAN Mode: Enter the storage device’s IP address. The default file path is
iqn.2004-05.storos.t-service ID, in which the service ID is user-defined when creating the
iSCSI volume of the network storage.
4.
Click Save to add the configured network disk.
5.
Initialize the added network disk.
a.
Click Remote Configuration  HDD Management to enter the HDD settings
interface.
800-15877V1 - A - 10/2013
64 | HVE Encoders User Guide
Figure 5-17
HDD Settings Interface
You can see the capacity, free space, status, type, and property of the added network
disk.
b.
If the status of the network disk is Uninitialized, select the disk from the list by
checking the checkbox, and then click the Init button to start initializing the disk.
When the initialization is complete, the disk Status will become Normal.
6.
Select the HDD No., and select the Property for the added network disk. For the Property,
choose from R/W or Read-only.
Note
Please refer to the user manual for IP SAN/NAS for the creation of the File Path in
Network Management.
Note
Up to 8 NAS disks or IP SAN disks can be connected.
Configuring SNMP Settings
Simple Network Management Protocol (SNMP) is an Internet-standard protocol for managing
devices on IP networks. You can use SNMP to get camera status, parameters, and alarm-related
information.
Before setting the SNMP, please ensure the following conditions are met:
•
The SNMP software is downloaded.
•
The encoder is configured to receive the device information via the SNMP port.
By setting the Trap Address, the device can send the alarm event and exception messages to
the surveillance center.
www.honeywell.com/security
Configuring the Encoder | 65
Note
The SNMP version you select should be the same as that of the SMNP software.
To configure the SNMP settings:
1.
Click Remote Configuration  Network Settings  SNMP to enter the SNMP settings
interface.
Figure 5-18
2.
Configure the following:
a.
Check the checkbox to enable SNMPv1 or SNMPv2c.
b.
Configure the Read SNMP Community (default: public) and the Write SNMP
Community (default: private).
c.
Configure the Trap Address (default: empty) and Trap Port (default: 162).
Note
3.
SNMP Settings Interface
You can enable both SNMPv1 and SNMPv2c.
After the SNMPv3 is enabled, you can configure the read username (default: public).
[Where does that window come from?]
800-15877V1 - A - 10/2013
66 | HVE Encoders User Guide
Figure 5-19
Note
4.
5.
SNMPv3 Settings Interface
By default, SNMPv1, SNMPv2c, and SNMPv3 are disabled.
Select a security level. Choose from:
•
no auth, no priv
•
auth, no priv
•
no auth, priv
•
auth, priv
Configure the Authentication Algorithm and Private-key Algorithm parameters.
•
You can configure the Authentication Algorithm and Private-key Algorithm parameters
if the security level is set to auth, priv.
•
You cannot configure the Authentication Algorithm and Private-key Algorithm
parameters if the security level is set to no auth, no priv.
6.
Set the SNMP Port (default: 161).
7.
Click Save to save these new settings.
Configuring QoS Settings
QoS (Quality of Service) can help with network delay and network congestion by configuring the
priority in which data is sent. The use of a QoS-aware network can prioritize traffic and therefore
allow critical flows to be served before lower priority flows.
The encoder can mark the data packets for video/audio, event/alarm, and management network
traffic with different DSCP values which identify different priority levels for sending data.
www.honeywell.com/security
Configuring the Encoder | 67
To configure QoS settings:
1.
Click Remote Configuration  Network Settings  QoS to enter the QoS settings
interface.
Figure 5-20
QoS Settings Interface
2.
Check the checkbox to enable the QoS function.
3.
Enter DSCP (Differentiated Services Codepoint) value for the following:
•
Video/Audio
•
Event/Alarm
•
Management traffic
The DSCP value is used to mark the traffic’s IP header. It defines the priority level for the
specified type of traffic, for example, how much bandwidth to reserve for it.
The valid range for DSCP is 0 to 63.
Higher DSCP values indicate higher priority levels.
4.
Click Save to save these new settings.
Note
You will have to reboot the encoder to activate the settings.
Configuring FTP Settings
Images captured by the encoder can be uploaded to an FTP server.
1.
Click Remote Configuration  Network Settings  FTP to enter the FTP settings
interface.
800-15877V1 - A - 10/2013
68 | HVE Encoders User Guide
Figure 5-21
FTP Settings Interface
2.
Check the checkbox to enable FTP.
3.
Configure the following settings:
•
Server Address
•
Port
•
User Name
•
Password
•
Directory
•
Upload Type
a.
Directory: In the Directory Structure field, you can select the root directory, parent
directory, and child directory.
If you select Parent Directory, then you have the option to use the Device Name,
Device Number, or Device IP for the name of the directory
If you select Child Directory, then you can use the Camera Name or Camera No. as
the name of the directory.
b.
4.
Upload Type: Check to enable uploading the captured picture to the FTP server.
Click Save to save these new settings.
Configuring SOCKS Settings
SOCKet Secure (SOCKS) is an Internet protocol that routes network packets between a client
and a server through a proxy server. This feature is useful if the encoder is located on a local
network behind a firewall, and Email notifications, FTP uploads, alarms, and such need to be
sent to a destination outside the local network (such as the Internet). SOCKS4 and SOCKS5 are
supported. SOCKS5 provides authentication so only authorized users may access a server.
To configure SOCKS settings:
www.honeywell.com/security
Configuring the Encoder | 69
1.
Click Remote Configuration  Network Settings  SOCKS to enter the SOCKS
settings interface.
Figure 5-22
2.
3.
SOCKS Settings Interface
Configure the following settings:
•
Server: Enter the address for the SOCKS server.
•
Server Port: Enter the port for the SOCKS server (default: 1080).
•
Server Type: Select the server type, either SOCKS4 or SOCKS5. When you select
SOCKS5, you can enable the user authentication on the server, and then enter the
login user name and password.
•
Local Networks: Define the local network segment which does not need to use the
SOCKS proxy server. You can enter multiple network addresses and use the
semicolon (;) to separate them. For example, 10.0.0.0/255.0.0.0;
172.16.0.0/255.240.0.0.
Click Save to save these new settings.
Configuring UPnP™ Settings
UPnP (Universal Plug and Play) permits the device seamlessly discover the presence of other
network devices on the network and establish functional network services for data sharing,
communications, etc. If you want to use the UPnP function to quickly connect the device to the
WAN via a router, then you should configure the UPnP parameters of the device.
Before configuring UPnP settings, please ensure the following conditions are met:
•
Enable the UPnP for the router to which your device is connected.
•
If the network working mode of the device is set to Multi-address, then the Default Route
of the device should be in the same network segment as that of the LAN IP address of the
router.
To configure UPnP settings:
1.
Click Remote Configuration  Network Settings  NAT to enter the NAT settings
interface.
800-15877V1 - A - 10/2013
70 | HVE Encoders User Guide
Figure 5-23
NAT Interface
2.
Check to Enable UPnP.
3.
Select the Port Mapping Mode to either Auto or Manual.
When you select Auto, then the mapping ports can be automatically assigned by the
router. Go to step 5. [?]
When you select Manual, then you should continue to step 4 to edit the mapping ports.
4.
Configure the HTTP Port (for access by WEB browser), SDK Port Mapping (for access by
client software), RTSP Port, and HTTPS Ports.
Note
5.
You can use the default port number, or change it according to your
requirements.
The Ports field indicate the port number for mapping in the router.
Click Save to save these new settings.
After successfully configuring port mapping, you can view the port mapping status on the
Port Mapping area of the NAT interface.
Configuring HTTPS Settings
HTTPS (Hyper Text Transfer Protocol Secure) ensures the transferred data is encrypted using
Secure Socket Layer (SSL) or Transport Layer Security (TLS). HTTPS provides authentication
of the web site and the associated web server that the encoder is communicating with, and
creates a secure channel over an insecure network. HTTPS URLs begin with https:// and use
port 443 by default.
To configure HTTPS settings:
1.
Click Remote Configuration  Network Settings  HTTPS to enter the HTTPS settings
interface.
www.honeywell.com/security
Configuring the Encoder | 71
Figure 5-24
2.
HTTPS Interface
Create the self-signed certificate or the authorized certificate.
Creating a self-signed certificate:
a.
Click Create next to Create Self-signed Certificate.
A dialog box opens.
Figure 5-25
Creating a Self-signed Certificate
b.
Enter the country, host name/IP, validity, and other information.
c.
Click OK to save these new settings.
Creating an authorized certificate:
3.
a.
Click Create next to Create Certificate Request.
b.
Download the certificate request and submit it to the trusted certificate authority for
signature.
c.
After receiving the signed valid certificate, import the certificate to the device.
When you have successfully created and installed the certificate, check the checkbox to
enable the HTTPS function.
800-15877V1 - A - 10/2013
72 | HVE Encoders User Guide
Note
After the HTTPS feature is enabled, the system will use the HTTPS login mode by
default when you input the IP address (for example,
https://192.168.0.250). You can also input http://IP address/index.asp
(for example, http://192.168.0.250/index.asp) if you want to use HTTP
mode to log into the device.
Configuring Bonjour Settings
Bonjour is enabled by default, and the video encoder can be automatically detected by
operating systems and clients that support this protocol. Bonjour is required for discovery using
the Honeywell IP Utility.
Before you configure Bonjour settings, please ensure that the following condition is met:
•
The Bonjour plugin is installed on your PC before enabling the Bonjour function.
To configure Bonjour settings:
1.
Click Remote Configuration  Network Settings  Bonjour to enter the Bonjour
settings interface.
Figure 5-26
Bonjour Settings Interface
2.
Click the checkbox to Enable Bonjour.
3.
Edit the device’s name. The name is shown when the device is detected by the system.
Note
4.
You can use only letters, numbers, and "-" for the device’s name.
Click Save to save these new settings.
Configuring the IP Address Filter
By enabling the IP Address Filter, you can allow or forbid certain IP addresses access to the
encoder.
Up to 256 IP addresses can be added to the list (allowed/forbidden) by Web Browser.
1.
Click Remote Configuration  Network Settings  IP Address Filter to enter the IP
address filter settings interface.
www.honeywell.com/security
Configuring the Encoder | 73
Figure 5-27
IP Address Filter Configuration Interface
2.
Check the checkbox to Enable IP Address Filter.
3.
Select the filter type for the IP address. Choose from Allowed or Forbidden.
4.
Click Add to add the IP address to the IP address filter.
Figure 5-28
Note
5.
Adding an IP Address to the IP Address Filter
Up to 256 IP addresses can be added to the allowed/forbidden list, by Web
browser.
Click Save to save these new settings.
Configuring the Multicast Address
The multicast address can be configured to allow live viewing of more than the maximum
number of cameras through the network.
A multicast address spans the Class-D IP range of 224.0.0.0 to 239.255.255.255. We
recommend that you use an IP address ranging from 239.252.0.0 to 239.255.255.255.
1.
Click Remote Configuration  Network Settings  Advanced to enter the Advanced
Settings interface.
Figure 5-29
Advanced Settings Interface
800-15877V1 - A - 10/2013
74 | HVE Encoders User Guide
2.
Enter the multicast address in the text field.
3.
Click Save to save these new settings.
www.honeywell.com/security
6
Configuring Camera Settings
6
Configuring OSD Settings
Configuring Display Settings
You can customize the camera name and configure and format the time display as it appears
on the screen.
1.
Click Remote Configuration  Camera Settings  Display Settings to enter the
Display Settings interface.
Figure 6-1
2.
Display Settings Interface
Select a camera from the drop-down menu.
800-15877V1 - A - 10/2013
76 | HVE Encoders User Guide
3.
Enter a camera name in the Camera Name text field.
Figure 6-2
Camera Name Text Field
4.
Click the boxes next to Display Name, Display Date, and Display Week to
enable/disable the display of those elements.
5.
Select the Time Format, Date Format, and OSD Display modes from their drop-down
menus.
6.
Adjust the location of the OSD by moving the text frame on the preview image.
Figure 6-3
Adjusting the OSD Display Position
12-11-2013- Tuesday 11:21:33
7.
(Optional) If you want to copy the display settings for the current camera to other cameras,
expand the Copy to Camera panel, and select the camera(s) to which to copy the
settings, or click Select All to select all cameras.
Figure 6-4
8.
Copying Settings to Other Cameras
Click Save to save these new settings.
Configuring Text Overlay
1.
Click Remote Configuration  Camera Settings  Text Overlay Settings to enter the
Text Overlay Settings interface.
www.honeywell.com/security
Configuring Camera Settings | 77
Figure 6-5
Text Overlay Configuration Interface
Enter text for overlay
Highway 1
2.
Select a camera from the drop-down list.
3.
Click the checkbox to enable editable text for that camera. In the editable text field next to
the camera, enter the desired text for the overlay.
4.
Click Save to save these new settings.
5.
Adjust the position of the overlayed text by moving the text frame on the preview image.
6.
(Optional) If you want to copy the text overlay settings for the current camera to other
cameras, expand the Copy to Camera panel, and select the camera(s) to which to copy
the settings, or click Select All to select all cameras.
Figure 6-6
7.
Copying Settings to Other Cameras
Click Save to save these new settings.
Configuring Video Settings
1.
Click Remote Configuration  Camera Settings  Video Settings to enter the Video
Settings interface.
800-15877V1 - A - 10/2013
78 | HVE Encoders User Guide
Figure 6-7
Video Settings Interface
2.
Select a camera from the drop-down list.
3.
Select the Stream Type for the camera. Choose from Main Stream (Normal), Main
Stream (Event), or Sub Stream.
Main Stream - Used for recording and live viewing with good bandwidth.
Sub Stream - Used for live viewing when the bandwidth is low.
For more information about changing the main stream to sub stream for live viewing,
please see Local Configuration Window on page 53.
4.
Customize the following settings for the selected Main or Sub stream:
Table 6-1
Customizeable Options for Video Main or Sub Streams
Option
Description
Video Type
Select the video type for streaming, including a video plus audio
composite stream. The audio signal will be recorded only when the
Video Type is selected as Video&Audio.
Resolution
Select the resolution for the video input.
Bitrate Type
Select the bitrate type as Constant or Variable.
Video Quality
When Variable is selected for the Bitrate type, you can choose from
up to 6 levels of video quality.
Frame Rate
Set the frame rate from 1 to 30 fps.
The Frame Rate is used to describe the frequency at which a video
stream is updated. This rate is measured in frames per second (fps).
Choose a higher frame rate when there is movement in the video
stream, as the higher frame rate maintains image quality.
www.honeywell.com/security
Configuring Camera Settings | 79
Table 6-1
Option
Description
Max. Bitrate
Set the maximum bit rate from 32 to 8192 Kbps.
I Frame Interval
Set the I frame interval from 1 to 400 (frames). The higher value
results in lower video quality.
Video Encoding
Select the video encoding standard. Choose from H.264, MPEG2,
MPEG4, or MJPEG.
Note
5.
When the MJPEG video encoding standard is selected, the frame rate can be set
from 1 to 15 fps, and the maximum bitrate is not configurable.
(Optional) If you want to copy the video settings for the current camera to other cameras,
expand the Copy to Camera panel, and select the camera(s) to which to copy the
settings, or click Select All to select all cameras.
Figure 6-8
6.
Customizeable Options for Video Main or Sub Streams
Copying Settings to Other Cameras
Click Save to save these new settings.
Configuring Snapshot Settings
You can configure scheduled snapshots and event-triggered snapshots. The captured pictures
can be stored on a HDD, on an SD card (if supported) or on the netHDD. You can also upload
the event-triggered snapshots to an FTP server.
To configure snapshot settings:
1.
Click Remote Configuration  Camera Settings  Snapshot to enter the Snapshot
settings interface.
800-15877V1 - A - 10/2013
80 | HVE Encoders User Guide
Figure 6-9
Snapshot Settings Interface
2.
Select a channel for capturing pictures.
3.
Configure the timed snapshot and event-triggered snapshot parameters, including the
format, resolution, quality, and the time that passes between two snapshots (interval). For
the interval, select from 1 sec, 2 sec, 3 sec, 4 sec, and 5 sec.
4.
(Optional) If you want to copy the snapshot settings for the current camera to other
cameras, expand the Copy to Camera panel, and select the camera(s) to which to copy
the settings, or click Select All to select all cameras.
Figure 6-10
5.
Copying Settings to Other Cameras
Click Save to save these new settings.
Note
Timed snapshots are stored on the HDD, the SD card (if supported), or
the netHDD. Event-triggered snapshots can be uploaded to FTP.
Check the Upload to FTP checkbox
in either the Motion
Detection Settings or the Alarm Input interface.
For more information, please see Configuring Motion Detection on page 81 or Configuring an
External Alarm Input on page 86.
For more information about FTP, please see Configuring FTP Settings on page 67.
www.honeywell.com/security
Configuring Camera Settings | 81
Configuring and Handling Alarms
This section explains how to configure the encoder to respond to alarm events. You can
configure the following settings:
•
Motion Detection
•
External Alarm Input
•
Video Loss Alarms
•
Tamper-proof Alarms
•
Handling Exceptions
Alarm events can trigger alarm actions, such as:
•
Notifying the Surveillance Center
•
Sending Emails
•
Triggering Alarm Output
Configuring Motion Detection
Motion Detection is a feature which can detect a motion event in the surveillance scene, then
alert personnel and record the video for the motion event.
Steps for Configuring for Motion Detection:
1.
Configure the Motion Detection Area. See Configuring the Motion Detection Area on page
81.
2.
Configure the Arming Schedule for Motion Detection. See Configuring the Arming
Schedule on page 82.
3.
Configure the Alarm Actions that are taken when a motion event is detected. See
Configuring the Alarm Actions for Motion Detection on page 83.
Configuring the Motion Detection Area
1.
Click Remote Configuration  Camera Settings  Motion Detection to enter the
Motion Detection settings interface.
800-15877V1 - A - 10/2013
82 | HVE Encoders User Guide
Figure 6-11
Motion Detection Settings Interface
2.
Select a camera to configure for motion detection.
3.
Check the checkbox to Enable Motion Detection.
4.
Click the Draw Area button
. Draw a motion detection area by clicking and
dragging the mouse in the live video image.
Note
5.
You can draw up to 8 motion detection areas within the same image.
Click Stop Drawing
Click Clear All
to finish drawing the motion detection area.
to clear all drawn areas.
6.
Move the slide bar
to set the sensitivity for the camera.
7.
Click Save to save these new settings.
Configuring the Arming Schedule
1.
Click the Arming Schedule tab.
www.honeywell.com/security
Configuring Camera Settings | 83
Figure 6-12
2.
Arming Schedule Tab
Click Edit to edit the arming schedule.
Note
The timing segments cannot overlap. Up to 8 segments can be
configured for each day.
The Holiday option is available in the Schedule drop-down list only after
you have enabled a holiday schedule in Holiday Settings.
3.
Choose the day for which you want to set the arming schedule.
4.
Click
5.
(Optional) After setting the arming schedule, you can copy the schedule to other days.
6.
Click OK to save these new settings.
to set the time period for the arming schedule.
Configuring the Alarm Actions for Motion Detection
You can specify the what happens (alarm type) when an event is triggered.
1.
Click the Linkage Method tab to enter the setting interface.
800-15877V1 - A - 10/2013
84 | HVE Encoders User Guide
Figure 6-13
2.
Linkage Method Tab for Motion Detection
Select the alarm linkage method(s), including Audible Warning, Notify Surveillance
Center, Send Email, and Upload to FTP.
Audible Warning: Triggers an audible beep from the encoder when an alarm is detected.
(HVE8/HVE8X models only)
Notify Surveillance Center: Sends an exception or alarm signal to a remote alarm host
when an event occurs. The alarm host is the PC that has the Remote Client installed.
Send Email: Sends an email with alarm information to a specified user or users when an
event occurs.
Note
To send an email when an event occurs, you first must go to the network setting
interface to set the related parameters. See Configuring Email Settings on page
61.
Upload to FTP: Captures an image when an alarm is triggered, and uploads the picture to
an FTP server.
3.
Select the channel for which you want to trigger an external alarm output when a motion
detection event occurs.
Figure 6-14
4.
Selecting an Alarm Output Channel
Configure Alarm Output settings.
a.
www.honeywell.com/security
Click Remote Configuration  Alarm Settings  Alarm Output to enter the Alarm
Output settings interface.
Configuring Camera Settings | 85
Figure 6-15
Alarm Output Settings Interface
b.
Select one alarm output channel in the Alarm Output drop-down list.
c.
The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min, or
Manual. The Delay refers to the time duration that the alarm output remains in effect
after an alarm occurs.
Note
d.
If you choose Manual, then you need to manually disable the alarm output.
Click Edit to enter the Edit Schedule Time interface.
800-15877V1 - A - 10/2013
86 | HVE Encoders User Guide
Figure 6-16
Edit Schedule Time Interface
The time schedule configuration is the same as the setting of the Arming Schedule for
Motion Detection.
See Configuring the Arming Schedule on page 82 for more about the Arming
Schedule.
e.
5.
Return to the Alarm Output Settings interface, then click Save to save these new
settings.
Select the channel on which you want to trigger recording when a motion detection event
occurs.
Figure 6-17
6.
Selecting a Channel for Motion Event Detection
Click Save to save these new settings.
Configuring an External Alarm Input
1.
Click Remote Configuration  Alarm Settings  Alarm Input to enter the Alarm Input
settings interface.
www.honeywell.com/security
Configuring Camera Settings | 87
Figure 6-18
Alarm Input Settings Interface
2.
Select an Alarm Input number and Alarm Type from their drop-down menus. Select from
NO (Normally Open) or NC (Normally Closed) for the Alarm Type.
3.
Set the arming schedule for the alarm input. See Configuring the Arming Schedule on
page 82 for more about the Arming Schedule.
4.
Click the Linkage Method tab to set the actions taken for the alarm input.
800-15877V1 - A - 10/2013
88 | HVE Encoders User Guide
Figure 6-19
Linkage Method Tab for Alarm Input Settings
For more information, please see Configuring the Alarm Actions for Motion Detection on
page 83.
5.
(Optional) You can also choose the PTZ linking for the alarm input if your camera is
installed with a PTZ camera.
a.
Choose the PTZ linking channel.
b.
Check the related checkbox to enable Preset Calling, Patrol Calling, or Pattern
Calling, then enter the preset/patrol/pattern number to be linked.
6.
(Optional) Copy these settings to other alarm inputs.
7.
Click Save to save these new settings.
Configuring a Video Loss Alarm
1.
Click Remote Configuration  Camera Settings  Video Loss to enter the Video Loss
settings interface.
www.honeywell.com/security
Configuring Camera Settings | 89
Figure 6-20
Video Loss Settings Interface
2.
Select a camera for which to configure the video loss alarm.
3.
Check the checkbox for Enable Video Loss.
4.
Click Edit to edit the arming schedule for video loss detection.
The arming schedule configuration is the same as the setting of the arming schedule for
motion detection.
Please see Configuring the Arming Schedule on page 82 for more information.
5.
Click the Linkage Method tab to set the actions taken when a video loss alarm is
triggered.
Please see Configuring the Alarm Actions for Motion Detection on page 83 for more
information.
Configuring the Tamper-proof Alarm
When you enable this function, an alarm will trigger whenever there’s tampering with the
camera’s image.
1.
Click Remote Configuration  Camera Settings  Tamper-proof to enter the
Tamper-proof Alarm settings interface.
800-15877V1 - A - 10/2013
90 | HVE Encoders User Guide
Figure 6-21
Tamper-proof Settings Interface
2.
Select a camera for which to configure the tamper-proof detection alarm.
3.
Click the Enable Tamper-proof checkbox.
4.
Set the tamper-proof area.
See Configuring the Motion Detection Area on page 81 for how to define an area.
5.
Click Edit to edit the arming schedule for the tamper-proof alarm.
Please see Configuring the Arming Schedule on page 82 for more information.
6.
Click the Linkage Method tab to set the actions taken when a video loss alarm is
triggered.
Please see Configuring the Alarm Actions for Motion Detection on page 83 for more
information.
Configuring Exception Handling
Choose what happens when an exception occurs. An exception is an event such as the
following:
•
HDD full
•
HDD error
•
Network disconnected
•
IP address conflict
•
Illegal access
•
Video standard mismatch
•
Video signal exception
•
Record/capture exception
•
Video resolution mismatch
www.honeywell.com/security
Configuring Camera Settings | 91
Note
When the resolution selected under Remote Configuration  Camera Settings
 Video Settings and the actual video input resolution do not match, you will
get an exception alarm. Please see Configuring Video Settings on page 77.
To configure exception handling:
1.
Click Remote Configuration  Exception to enter the Exceptions Settings interface.
Figure 6-22
Exception Settings Interface
2.
Check the appropriate checkboxes for the actions you wish to take place when an
Exception alarm is triggered. For more information, please see Configuring the Alarm
Actions for Motion Detection on page 83.
3.
Click Save to save these new settings.
Configuring a Privacy Mask
The Privacy Mask enables you to cover certain areas on the video channel to prevent sensitive
areas from being viewed or recorded.
To configure a privacy mask:
1.
Click Configuration  Remote Configuration  Camera Settings  Privacy Mask to
enter the Privacy Mask settings interface.
800-15877V1 - A - 10/2013
92 | HVE Encoders User Guide
Figure 6-23
Privacy Mask Settings Interface
2.
Select a camera for which you want to configure a privacy mask.
3.
Check the Enable Privacy Mask checkbox to enable this function.
4.
Click the Draw Area button
5.
Draw a motion privacy mask area by clicking and dragging the mouse in the live video
image.
Note
6.
You can draw up to 4 privacy mask areas.
Click Stop Drawing
Click Clear All
7.
.
to finish drawing the motion detection area.
to clear all drawn areas.
Click Save to save these new settings.
www.honeywell.com/security
Configuring Camera Settings | 93
Configuring RS-232/RS-485 Port Settings
Configuring RS-232 Port Settings
Note
HVE1/HVE1X encoders do not have an RS-232 serial port.
Through the serial port management tools, the RS-232 serial port can be used for configuration.
1.
Click Remote Configuration  Serial Port Settings  232 Serial Port to enter the 232
Serial Port settings interface.
Figure 6-24
Note
2.
RS-232 Serial Port Settings Interface
If you want to connect the encoder by the RS-232 port, the parameters of the
RS-232 port should be exactly the same as the parameters you configured here.
Click Save to save these new settings.
Configuring the RS-232 Port as a Transparent Channel
In order to receive data, you must set the RS-232 port as a transparent channel.
Setting the RS-232 port as a transparent channel:
1.
Click Remote Configuration  Serial Port Settings  232 Serial Port to enter the
RS-232 Settings interface.
800-15877V1 - A - 10/2013
94 | HVE Encoders User Guide
Figure 6-25
RS-232 Settings Interface
2.
Select Transparent Channel from the Usage drop-down menu.
3.
Click Save to save this new setting.
Configuring RS-485 Port Settings
The RS-485 serial port is used to control PTZ cameras. You must configure the PTZ parameters
before you can control the PTZ unit.
1.
Click Remote Configuration  Serial Port Settings  485 Serial Port to enter the
RS-485 Serial Port Settings interface.
Figure 6-26
www.honeywell.com/security
RS-485 Serial Port Settings Interface
Configuring Camera Settings | 95
2.
Set the RS-485 parameters.
Table 6-2
Setting
Default
Baud Rate
9600
Data Bit
8
Stop Bit
1
Parity
None
Flow Control
None
Note
3.
Default RS-485 Port Settings
The Baud Rate, Address, and PTZ Protocol parameters should be exactly the
same as the parameters of the connected PTZ camera.
Click Save to save these new settings.
800-15877V1 - A - 10/2013
96 | HVE Encoders User Guide
www.honeywell.com/security
7
Configuring Recording and Capturing
Settings
7
Before configuring the settings for recording and capturing, ensure that the following conditions
are met:
•
Ensure that the encoder is connected to an HDD (if supported), network disk, or microSD
card (if supported).
•
Ensure that the HDD or network disk has been initialized for first-time use.
For more information about storage, please see Adding the Network Disk on page 63.
You can choose from two recording/capturing types: Manual or Scheduled.
Configuring Holiday Settings
It’s a good idea to have a different plan for recording during holidays.
1.
Click Remote Configuration  Camera Settings  Holiday Settings to enter the
holiday settings interface.
800-15877V1 - A - 10/2013
98 | HVE Encoders User Guide
Figure 7-1
2.
Select a holiday from the Holiday Settings list, then click
Holiday interface opens.
Figure 7-2
3.
Holiday Settings Interface
to edit the holiday. The Edit
Edit Holiday Interface
a.
Enter the holiday name.
b.
Check the checkbox to enable the holiday.
c.
Select the holiday type from the drop-down list. Choose from By Month, By Week, or
By Date.
d.
Set the Start and End Dates.
e.
Click OK to save these new settings, and to go back to the Holiday Settings
interface.
Check the Holiday Settings list to ensure that the correct settings have been entered.
Figure 7-3
Checking the Holiday Settings List
Repeat these steps for each holiday. Up to 32 holidays can be configured.
www.honeywell.com/security
Configuring Recording and Capturing Settings | 99
Note
The Holiday option is available in the Schedule drop-down list after you have
enabled Holiday Schedule in Holiday Settings.
Configuring Scheduled Recording and Capturing
1.
Click Remote Configuration  Camera Settings  Schedule Settings to enter the
Schedule Settings interface.
Figure 7-4
Schedule Settings Interface
2.
From the drop-down menu, select the camera for which you want to configure the
recording or capturing schedule.
3.
Click the Record or Capture tab.
4.
Check the checkbox for either Enable Record Schedule or Enable Capture Schedule to
enable that function.
5.
Click Edit to enter the Edit Schedule interface.
800-15877V1 - A - 10/2013
100 | HVE Encoders User Guide
Figure 7-5
6.
Edit Schedule Interface
Choose the day of the week for which you want to configure scheduled recording or
capturing.
a.
Select All Day or configure a Customized time period.
•
If you want to configure an all-day recording/capturing period, then please check the
All Day checkbox.
•
If you want to configure a specific time period for recording/capturing, then please
check the Customize checkbox. Then enter a Start Time and an End Time period.
Note
www.honeywell.com/security
The time of each holiday period cannot overlap. Up to 8 periods can be
configured.
Configuring Recording and Capturing Settings | 101
b.
Select either a Record Type or a Capture Type. Choose from Normal, Motion,
Alarm, Motion&Alarm, and Motion/Alarm.
Table 7-1
Recording and Capturing Types
Type
Description
Normal
If you select Normal, then the video will be recorded/captured
automatically according to the schedule.
Motion Detection
If you select Motion, then the video will be recorded/captured
when motion is detected.
Besides configuring the record/capture schedule, you have to
set the motion detection area and check the Trigger Channel
checkbox for the Linkage Method in the Motion Detection
settings interface.
See Configuring Motion Detection on page 81.
Alarm
If you select Alarm, then the video will be recorded/captured
when the alarm is triggered.
Besides configuring the record/capture schedule, you have to
set the Alarm Type and check the Trigger Channel checkbox
for the Linkage Method in the Motion Detection settings
interface.
See Configuring Motion Detection on page 81.
Motion & Alarm
If you select Motion & Alarm, then the video will be
recorded/captured when motion is detected and the alarm are
triggered at the same time.
Besides configuring the record/capture schedule, you have to
configure the settings on the Motion Detection and Alarm
Input Settings interfaces.
See Configuring Motion Detection on page 81.
See Configuring External Alarm Input on page 86.
Motion or Alarm
If you select Motion | Alarm, the video will be
recorded/captured when the alarm is triggered or motion is
detected.
Besides configuring the record/capture schedule, you have to
configure the settings on the Motion Detection and Alarm
Input Settings interfaces.
See Configuring Motion Detection on page 81.
See Configuring External Alarm Input on page 86.
c.
(Optional)
Check the Select All checkbox, then click Copy to copy these settings to the whole
week.
Select individual days to which to copy these settings by clicking the appropriate
checkbox.
d.
7.
Click OK to save these new settings and to then exit the Edit Schedule interface.
Click Advanced to configure advanced recording parameters such as Pre- and Post-Event
recording intervals, and when to overwrite recordings and to record audio.
800-15877V1 - A - 10/2013
102 | HVE Encoders User Guide
Figure 7-6
Advanced Recording Parameters
Pre-Record: Choose from No Pre-Record, 5 sec, 10 sec, 15 sec, 20 sec, 25 sec, or 30
sec.
Post Record: Choose from 5 sec, 10 sec, 30 sec, 1 min, 2 min, 5 min, or 10 min.
8.
To copy the recording settings of the current camera to other cameras, expand the Copy
to Camera panel, then either select specific cameras to which you want to copy the
settings, or click Select All to select all cameras.
Figure 7-7
9.
Copying the Settings to Other Cameras
Click Save to validate these new settings.
www.honeywell.com/security
8
Playing Back Recorded Video
8
Recorded video files can be remotely played back through a Web browser.
Before playing back recorded video, ensure that the following conditions are met:
•
Ensure that the encoder is connected to an HDD (if supported), network disk, or microSD
card (if supported).
•
Ensure that the HDD or network disk has been initialized for first-time use.
Playing back recorded video:
1.
Click Playback on the menu bar to enter the playback interface.
Figure 8-1
Playback Interface
2.
Select a camera from the device list for playback.
3.
Select a day from the calendar, and then click Search.
800-15877V1 - A - 10/2013
104 | HVE Encoders User Guide
Figure 8-2
4.
Click Play to play the video found for that date.
Figure 8-3
Table 8-1
Button
Calendar
Playing Back Video
Playback Controls
Function
Button
Function
Select window division mode
Play/Pause
Stop playback
Reverse playback?
Fast forward
Play by single frames
Stop all channels from playing
Capture pictures in playback mode
Download video files
Start/Stop clipping video files
Audio on/off
www.honeywell.com/security
Playing Back Recorded Video | 105
Playing Back a Specific Time
You can use the mouse to drag the progress bar to locate an exact playback point.
Figure 8-4
Playback Slidebar
Or you can enter the specific time in the time field
, then click
.
Determining the Type of Recorded Video
The recorded video is assigned a specific color which indicates the type of video.
Figure 8-5
Recorded Video Color Key
800-15877V1 - A - 10/2013
106 | HVE Encoders User Guide
www.honeywell.com/security
9
Managing User Accounts
9
Click Remote Configuration  Remote Configuration  User Management to enter the
User Management settings interface.
Figure 9-1
User Management Settings Interface
Only an admin user has the ability to create normal users. Up to 31 users can be created.
Adding a User
1.
Click Add to enter the Add User interface.
800-15877V1 - A - 10/2013
108 | HVE Encoders User Guide
Figure 9-2
Add User Interface
2.
Enter a User Name and Password, and then confirm the password.
3.
Select a user Level. Choose from Operator or User.
The user levels have different permissions.
Operator: Operators have access to the following: Local Log Search in the Local
Configuration, Remote Log Search and Two-way Audio in Remote Configuration, and all
operating permissions in Camera Configuration.
User: Guest users have access to the following: Local Log Search in the Local
Configuration, Remote Log Search in Remote Configuration, and only local/remote
playback in Camera Configuration.
4.
Configure the user permissions for the selected user account, including Basic
Permissions and Camera Operation.
5.
Click OK to save these new changes.
Modifying a User
Note
1.
You need the admin password to modify the admin user.
Select a user account from the list on the User Information interface.
www.honeywell.com/security
Managing User Accounts | 109
Figure 9-3
2.
Click Modify to enter the Modify User interface.
Figure 9-4
3.
User Account - Modifying a User
Modify User Interface
Make the necessary changes, and then click OK to save these new settings.
Deleting a User
1.
Select a user account from the list on the User Information interface.
2.
Click Delete, and a confirmation message pops up.
Figure 9-5
Confirmation Message for Deleting a User
800-15877V1 - A - 10/2013
110 | HVE Encoders User Guide
3.
Click OK to confirm the deletion of the selected user account.
www.honeywell.com/security
10
Searching Logs, Viewing Device Information,
and Maintaining the Encoder
10
Searching Logs
Log files store operation, alarm, and exception information for the device. These log files can be
viewed and exported at any time.
Before you begin, ensure that the following conditions are met:
•
Ensure that the encoder is connected to an HDD (if supported), network disk, or microSD
card (if supported).
•
Ensure that the HDD or network disk has been initialized for first-time use.
For more information about storage, please see Adding the Network Disk on page 63.
1.
Click Log on the menu bar to enter the Log interface.
Figure 10-1
Log Interface
2.
Enter log search conditions to refine the search, including Major Type, Minor Type, Start
Time, and End Time.
3.
Click Search.
800-15877V1 - A - 10/2013
112 | HVE Encoders User Guide
The log files that match the search criteria display in the log list. See Figure 10-1.
Note
4.
Up to 100 log files can be displayed at a time.
Click
to save the searched log files to a local directory.
Viewing Device Information
Click Remote Configuration  Device Parameters  Device Information to enter the device
Basic Information interface.
Figure 10-2
Basic Device Information Configuration Interface
You can edit the Device Name and the Device No.. You can view the device information,
including Model, Serial No., Firmware/Encode Version, Number of Channels, Number of
HDDs, and Number of Alarm Input / Output.
www.honeywell.com/security
Searching Logs, Viewing Device Information, and Maintaining the Encoder | 113
Maintenance
In the Maintenance interface, you can reboot the encoder, restore it to default settings, import
and export configuration files, and upgrade the system.
Click Remote Configuration  Maintenance to enter the Maintenance interface.
Figure 10-3
Maintenance Interface
Restarting the Encoder
1.
Click Reboot on the Maintenance interface.
A confirmation message appears.
Figure 10-4
2.
Confirmation Message for Rebooting the Encoder
Click OK to reboot the encoder. Click Cancel to cancel rebooting the recorder.
Restoring Default Settings
1.
Click Restore or Default on the Maintenance interface.
800-15877V1 - A - 10/2013
114 | HVE Encoders User Guide
Figure 10-5
Restore or Default Interface
•
Select Restore to restore the encoder to the default settings for all parameters except
the IP address, the subnet mask, the gateway, and the port.
•
Select Default to restore the encoder to the default settings for all parameters.
A confirmation message appears.
Figure 10-6
2.
Confirmation Message for Restoring or Returning the Encoder to
Defaults
Click OK to restore the encoder to default settings and then reboot the device to validate
the settings.
Importing or Exporting Configuration Files
The encoder’s configuration files can be exported to a local device for backup. The
configuration files of one encoder can be imported to multiple encoders if they are to be
configured with the same parameters.
Importing Configuration Files
1.
Click Maintenance  Import Config File to open the Import Config. File interface.
Figure 10-7
Import Configuration File Interface
2.
Click Browse to select the file from the selected backup device.
3.
Click the Import button to import a configuration file.
Note
www.honeywell.com/security
After importing configuration files, the encoder reboots automatically.
Searching Logs, Viewing Device Information, and Maintaining the Encoder | 115
Exporting Configuration Files
1.
Click Maintenance  Export Config File to open the Export Config. File interface.
2.
Click the Export button to export configuration files to the selected local backup device.
Upgrading the System
1.
Click Maintenance  Remote Upgrade to open the Remote Upgrade interface.
Figure 10-8
Remote Upgrade Interface
2.
Click Browse to select the local update file.
3.
Click Upgrade to start remote upgrade.
800-15877V1 - A - 10/2013
116 | HVE Encoders User Guide
www.honeywell.com/security
A
Troubleshooting
A
The encoder cannot be pinged
Possible
solutions:
•
Check the cable connections between the encoder and the switch.
•
Please see Configuring Network Parameters on page 39, and ensure that the device’s IP
matches your computer’s IP.
The transparent channel has been set, but the encoder still
does not receive data
Possible
solutions
•
Ensure that the RS-232 port has been set as a transparent channel. See Configuring the
RS-232 Port as a Transparent Channel on page 93.
•
Ensure that the encoder is properly connected.
The encoder cannot be added with the software
Possible
solution:
•
Check the encoder IP.
•
Ensure that the encoder is properly connected.
•
Ensure that the user name and password for the encoder are correct.
800-15877V1 - A - 10/2013
118 | HVE Encoders User Guide
The encoder cannot control a PTZ camera
Possible
solution:
•
Check the RS-485 connections between the encoder and PTZ camera.
•
Ensure that the PTZ address, protocol, and baud rate settings for the encoder match the
same settings on the connect PTZ camera.
Video cannot be viewed through the Web browser
Possible
solution:
•
Check the network connection.
•
Ensure that the encoder username and password are entered correctly.
•
Ensure that the encoder port is entered correctly.
www.honeywell.com/security
B
HVE1(X) Specifications
B
This section lists the technical specifications for the HVE1 1-channel encoder.
Operational
Video Compression
H.264/MPEG4/MPEG2/MJPEG
Video Input
1 channel
Audio Compression
G.71u
Audio Input
1 channel
Two-way Audio Input
1 channel
Audio Output
1 channel
Recording Resolution
4CIF/2CIF/CIF/QCIF
Frame Rate
H.264/MPEG4/MPEG2 encoding: 25 fps (P) / 30 fps (N);
MJPEG encoding: 15 fps
Video Bit Rate
32 Kbps ~ 3072 Kbps, or user defined (Max. 8192 Mbps)
Audio Bit Rate
64 kbps
Dual Stream
Supported
Stream Type
Video / Video + Audio
Data Storage Type
NAS, microSD
Data Storage Capacity
4 GB up to 32 GB and above, Class 6 and above for microSD
storage
Network Protocols
IPv4/v6, HTTP, HTTPS, QoS layer3 DiffServ, FTP, SMTP,
Bonjour, UPnPTM, SNMPv1/v2c/v3(MIB-II), DNS, DynDNS,
hkDDNS, NTP, RTSP, RTP/RTCP,TCP, UDP, IGMP, ICMP,
DHCP, ARP, SOCKSv4/v5, PSIA, ONVIF, HIKCGI, netFilter
Electrical
Power Supply
12 V DC
Power Consumption
8W
Mechanical
Dimensions (W x H x D)
3.1 x 1.5 x 3.5 inches
(80 × 39 × 90 mm)
Weight
 1.1 lbs (0.5 kg)
Construction
Housing: Die-cast aluminum
800-15877V1 - A - 10/2013
120 | HVE Encoders User Guide
Connections
Video Input
BNC 1 Vp-p @ 75 ohms
Video Output
1 - Composite main monitor,
BNC 1 Vp-p @ 75 ohms
1 - VGA Main Monitor
1 - Spot BNC 1 Vp-p @ 75 ohms
Audio Input
3.5 mm interface (2.0 Vp-p, 1 ohm) (LINE IN)
Audio Output
3.5 mm interface (Linear, 600 ohms)
Two-way Audio Input
3.5 mm interface (2.0 Vp-p, 1 ohm) (LINE IN)
Network Interface
1 RJ-45 10 M / 100 Mbps adaptive Ethernet interface (PoE)
Serial Interface
1 half-duplex RS-485 interface
Alarm In
1
Alarm Out
1
Data Storage
1 microSD interface
Environmental
Temperature
Operating: 14°F to 131°F (-10°C to 55°C)
Storage: -4°F to 149°F (-20°C to 65°C)
Relative Humidity
10% to 90%, non-condensing
Regulatory
Emissions
EN 55022 FCC Part 15B, Class A
Immunity
EN 50130-4
Safety
EN 60950-1
North America ETL listed to UL/CSA 60950-1
www.honeywell.com/security
HVE1(X) Specifications | 121
Dimensions
1.5 "
39 mm
2.6 "
66 mm
3.1 "
80 mm
4.2 "
106.5 mm
3.5 "
90 mm
800-15877V1 - A - 10/2013
122 | HVE Encoders User Guide
www.honeywell.com/security
C
HVE4(X) Specifications
C
This section lists the technical specifications for the HVE4 4-channel encoder.
Operational
Video Compression
H.264/MPEG4/MPEG2/MJPEG
Video Input
4 channels
Audio Compression
G.71u
Audio Input
4 channels
Two-way Audio Input
1 channel
Audio Output
1 channel
Recording Resolution
4CIF/2CIF/CIF/QCIF
Frame Rate
H.264/MPEG4/MPEG2 encoding: 25 fps (P) / 30 fps (N);
MJPEG encoding: 15 fps
Video Bit Rate
32 Kbps ~ 3072 Kbps, or user defined (Max. 8192 Mbps)
Audio Bit Rate
64 kbps
Dual Stream
Supported
Stream Type
Video / Video + Audio
Data Storage Type
NAS, microSD
Data Storage Capacity
16 GB up to 32 GB and above, Class 6 and above for microSD
storage
Network Protocols
IPv4/v6, HTTP, HTTPS, QoS layer3 DiffServ, FTP, SMTP,
Bonjour, UPnPTM, SNMPv1/v2c/v3(MIB-II), DNS, DynDNS,
hkDDNS, NTP, RTSP, RTP/RTCP,TCP, UDP, IGMP, ICMP,
DHCP, ARP, SOCKSv4/v5, PSIA, ONVIF, HIKCGI, netFilter
Electrical
Power Supply
12 V DC
Power Consumption
8W
Mechanical
Dimensions (W x H x D)
4.5 x 1.9 x 128 inches
(114 × 48 × 5.0 mm)
Weight
 2.2 lbs ( 1.0 Kg)
Construction
Housing: Die-cast aluminum
800-15877V1 - A - 10/2013
124 | HVE Encoders User Guide
Connections
Video Input
BNC 1 Vp-p @ 75 ohms
Video Output
1 - Composite main monitor,
BNC 1 Vp-p @ 75 ohms
1 - VGA Main Monitor
1 - Spot BNC 1 Vp-p @ 75 ohms
Audio Input
3.5 mm interface (2.0 Vp-p, 1 ohm) (LINE IN)
Audio Output
3.5 mm interface (Linear, 600 ohms)
Two-way Audio Input
3.5 mm interface (2.0 Vp-p, 1 ohm) (LINE IN)
Network Interface
1 RJ-45 10 M / 100 Mbps adaptive Ethernet interface (PoE)
Serial Interface
1 half-duplex RS-485 interface
1 RS-232 interface
Alarm In
4
Alarm Out
2
Data Storage
1 microSD interface
Environmental
Temperature
Operating: 14°F to 131°F (-10°C to 55°C)
Storage: -4°F to 149°F (-20°C to 65°C)
Relative Humidity
10% to 90%, non-condensing
Regulatory
Emissions
EN 55022 FCC Part 15B, Class A
Immunity
EN 50130-4
Safety
EN 60950-1
North America ETL listed to UL/CSA 60950-1
www.honeywell.com/security
HVE4(X) Specifications | 125
Dimensions
3.9 "
100.0 mm
1.9 "
47.5 mm
4.5 "
114.0 mm
5.5 "
140.4 mm
5.0 "
127.5 mm
800-15877V1 - A - 10/2013
126 | HVE Encoders User Guide
www.honeywell.com/security
D
HVE8(X) Specifications
D
This section lists the technical specifications for the HVE8 8-channel encoder.
Operational
Video Compression
H.264/MPEG4/MPEG2/MJPEG
Video Input
8 channels
Audio Compression
G.71u
Audio Input
8 channels
Two-way Audio Input
1 channel
Audio Output
1 channel
Recording Resolution
4CIF/2CIF/CIF/QCIF
Frame Rate
H.264/MPEG4/MPEG2 encoding: 25 fps (P) / 30 fps (N);
MJPEG encoding: 15 fps
Video Bit Rate
32 Kbps ~ 3072 Kbps, or user defined (Max. 8192 Mbps)
Audio Bit Rate
64 kbps
Dual Stream
Supported
Stream Type
Video / Video + Audio
Data Storage Type
NAS, SATA
Data Storage Capacity
Up to 4 TB capacity for each disk
Network Protocols
IPv4/v6, HTTP, HTTPS, QoS layer3 DiffServ, FTP, SMTP,
Bonjour, UPnPTM, SNMPv1/v2c/v3(MIB-II), DNS, DynDNS,
hkDDNS, NTP, RTSP, RTP/RTCP,TCP, UDP, IGMP, ICMP,
DHCP, ARP, SOCKSv4/v5, PSIA, ONVIF, HIKCGI, netFilter
Electrical
Power Supply
12 V DC
Power Consumption
 30 W
Mechanical
Dimensions (W x H x D)
12.4 x 1.8 x 7.9 inches
(315 × 45 × 200 mm)
Weight
 4.4 lbs ( 2.0 Kg)
Construction
Housing: Steel chassis
800-15877V1 - A - 10/2013
128 | HVE Encoders User Guide
Connections
Video Input
BNC 1 Vp-p @ 75 ohms
Video Output
1 - Composite main monitor,
BNC 1 Vp-p @ 75 ohms
1 - VGA Main Monitor
1 - Spot BNC 1 Vp-p @ 75 ohms
Audio Input
3.5 mm interface (2.0 Vp-p, 1 ohm) (LINE IN)
Audio Output
3.5 mm interface (Linear, 600 ohms)
Two-way Audio Input
3.5 mm interface (2.0 Vp-p, 1 ohm) (LINE IN)
Network Interface
1 RJ-45 10 M / 100 Mbps / 1000 Mbps adaptive Ethernet
interface
Serial Interface
1 half-duplex RS-485 interface
1 RS-232 interface
Alarm In
8
Alarm Out
4
Environmental
Temperature
Operating: 14°F to 131°F (-10°C to 55°C)
Storage: -4°F to 149°F (-20°C to 65°C)
Relative Humidity
10% to 90%, non-condensing
Regulatory
Emissions
EN 55022 FCC Part 15B, Class A
Immunity
EN 50130-4
Safety
EN 60950-1
North America ETL listed to UL/CSA 60950-1
www.honeywell.com/security
HVE8(X) Specifications | 129
Dimensions
1.8 "
44.5 mm
7.9"
200.8 mm
8.3 "
211.5 mm
1.8 "
44.5 mm
12.4 "
315.0 mm
800-15877V1 - A - 10/2013
130 | HVE Encoders User Guide
www.honeywell.com/security
| 131
Index
A
C
adding
users 107
alarm actions configuration 83
alarm center notification 84
alarm host 84
alarm inputs
connections 33
number of 112
alarm outputs
connections 34
number of 112
alarm recording 101
alarm setup
emerson alarm 33
alarm-in connectors 29, 31, 33
alarm-out connectors 29, 31, 33
alarms
alarm center notification 84
audible warning 84
configuration 81
linking a preset to 50
sending emails 84
uploading to ftp 84
arming schedule configuration 82
attach image 62
audible warning 84
audio 78
audio on/off 46, 104
audio-in connectors 30
audio-out connector 28, 30, 32
authentication request 62
authorized certificate, creating 71
Canadian compliance 16
capture an image 46
cautions 15
choose receiver 62
clipping video files 104
compliance
Canadian 16
FCC 15
configuration files
exporting 115
importing 114
configuring
a privacy mask 91
a video loss alarm 88
alarm actions 83
alarm center notification 84
alarms 81
arming schedule 82
audible warning 84
audio 78
bitrate 78
bonjour settings 72
clip save location 54
date manually 55
DDNS 59
DHCP server 57
display settings 75
DNS server 57
downloaded files save path 54
DynDNS 59
email settings 61
encoder 53
exception handling 90
external alarm inputs 86
frame rate 78
ftp directories 68
ftp settings 67
holiday settings 97
HTTPS settings 70
HVEDDNS 60
I frame interval 79
image capture settings 47
B
baud rate, default 95
bitrate 78
bonjour settings configuration 72
brightness 44
browser 37
800-15877V1 - A - 10/2013
132 | HVE Encoders User Guide
image size 53
IP address 72
IP server 58
live view performance 54
maximum bitrate 79
motion detection 81
motion detection area 81
multicast address 73
NetHDD 63
network settings 56
PeanutHull 59
port mapping mode 70
port settings 57
PPPoE 60
protocol type 53
PTZ camera 48
QoS settings 66
recorded files save location 54
recording file size 53
recording type 101
resolution 78
RS-232 port as a transparent channel 93
RS-232 serial port 93
RS-485 port 48
RS-485 serial port 93
schedule image capture 99
schedule time 85
scheduled recording 99
sending emails 84
snapshot settings 79
snapshots save location 54
SNMP settings 64
SOCKS settings 68
stream type 53, 78
tamper-proof alarms 89
TCP/IP settings 56
text overlay 76
time manually 55
time settings 54
upload to ftp 84
UPnP settings 69
video encoding standard 79
video parameters 50
video quality 78
video settings 77
video type 78
connecting
alarm inputs 33
alarm outputs 34
PTZ cameras 48
connectors
alarm-in 29, 31, 33
alarm-out 29, 31, 33
audio-in 30
audio-out 28, 30, 32
line-in 28, 30
RS-232 31, 33
RS-485 29, 31, 33
www.honeywell.com/security
video-in 28, 30, 32
contrast 44
controlling PTZ cameras 49
creating
authorized certificates 71
self-signed certificates 71
D
data bit, default 95
date configuration 55
daylight saving time 56
DDNS 58
DDNS configuration 59
Declaration of Conformance 16
default
baud rate 95
data bit 95
Diamond PTZ protocol 48
file path for IP SAN 63
file path for NAS 63
flow control, flow control, default 95
HTTP port 57
HTTPS port 57, 70
live video brightness 52
live video contrast 52
live video denoising level 52
live video hue 52
live video saturation 52
live video sharpness 52
parity 95
restoring live video to default settings 52
RTSP port 57
server port 69
SMTP port 62
SNMP 65
SNMP port 66
SNMPv3 username 65
stop bit 95
TCP/IP port 62
trap address 65
trap port 65
video standard setting 51
default settings, restoring to 113
deleting users 109
device information, viewing 112
device IP password factory default 37
device name 112
device number 112
device password factory default 37
DHCP 57
Diamond PTZ protocol default 48
differentiated services codepoint 67
display settings configuration 75
DNS 57
download video files 104
DSCP 67
DST 56
| 133
DynDNS 58
DynDNS configuration 59
hue 44
HVEDDNS configuration 60
E
I
email settings
attach image 62
authentication request 62
choose receiver 62
interval 62
receiver’s address 62
receiver’s name 62
sender’s address 62
sender’s name 62
SMTP port 62
SMTP server 62
SSL 62
email settings configuration 61
emerson alarm 33
encoder configuration 53
encoder, restarting 113
encoding version 112
exception handling configuration 90
exporting configuration files 115
external alarm input configuration 86
I frame interval 79
image capture 46, 104
image capture settings 47
image size 53
importing configuration files 114
initializing the added network disk 63
initializing the HDD 63
installing
hard disk drive 25
IP utility 37
interval 62
IP address filter configuration 72
IP network settings 41
IP SAN default path 63
IP SAN disks, how many can be connected 64
IP SAN mode 63
IP server configuration 58
IP utility installation 37
IPv4 56
F
factory defaults
device IP password 37
device password 37
user name 37
FCC compliance 15
features
alarm 23
encoding 22
exceptions 23
logs 24
network 22
ptz 23
firmware version 112
frame rate 78
ftp
directories configuration 68
settings configuration 67
uploading to 80
H
H.264 79
hard disk drive 25
HDD 25
compatible models 26
HDD, initializing 63
holiday periods, how many are available 100
holiday settings configuration 97
HTTP port default 57
HTTPS port default 57, 70
HTTPS settings configuration 70
J
JJ1 relay 35
L
LAN 29, 31, 33
LED 32
line-in connector 28, 30
live view performance 54
live view settings 44
log search 111
M
manual recording 46
manual time sync 55
maximum bitrate 79
maximum number of user accounts 107
menu bar 44
microSD card slot 28, 31
MJPEG 79
model 112
modifying users 108
motion and alarm recording 101
motion detection 81
motion detection area 81
motion detection areas, how many 82
motion or alarm recording 101
motion recording 101
MPEG2 79
MPEG4 79
MTU 56
multicast address configuration 73
800-15877V1 - A - 10/2013
134 | HVE Encoders User Guide
N
NAS default path 63
NAS disks, how many can be connected 64
NAS mode 63
NetHDD settings 63
network parameters, modifying 41
network settings, configuring 56
network time protocol 55
NIC 56
normal recording 101
NTP 55
number (maximum) of motion detection areas 82
number of channels 112
number of HDDs 112
O
operating system requirements 37
OS 37
P
parity, default 95
PeanutHull configuration 59
PoE 29, 31, 33
port mapping mode 70
port settings configuration 57
power indicator 28, 30
power supply 29, 31, 33
PPPoE configuration 60
preset, linking to an alarm 50
presets 44
privacy mask configuration 91
privacy mask, how many are available 92
protocol type 53
PTZ
camera configuration 48
camera connections 48
camera controls 49
controls 44
setting a preset 49
Q
QoS settings, configuring 66
R
receiver’s address 62
receiver’s name 62
record 46
recording file size 53
regulatory 15
related documents 20
reset 28, 31, 33
resolution 78
restarting
encoder 113
RS-232 31, 33
www.honeywell.com/security
RS-232 port
configuring as a transparent channel 93
RS-232 serial port configuration 93
RS-485 29
RS-485 connectors 31, 33
RS-485 serial port configuration 48, 93
RTSP port default 57
S
safety instructions 16
saturation 44
save clips location 54
save location for recorded files 54
saving path for snapshots 54
schedule image capture 99
schedule recording 99
schedule time configuration 85
searching logs 111
self-signed certificates 71
sender’s address 62
sender’s name 62
sending emails 84
serial number 112
serial port configuration 48
server port default 69
setting
RS-232 port as a transparent channel 93
setting a PTZ preset 49
settings
IP network 41
SMTP port 62
SMTP port default 62
SMTP server 62
snapshot settings 79
SNMP default settings 65
SNMP port default 66
SNMP settings 64
SNMPv3 default username 65
SOCKS settings configuration 68
SSL 62
status indicator 32
stop bit, default 95
stream type 53, 78
supported web browsers 42
system upgrade 115
T
tamper-proof alarm configuration 89
TCP/IP port default 62
TCP/IP settings 56
text overlay configuration 76
time configuration 55
time settings 54
time zone 55
transparent channel, configuring RS-232 port as 93
trap address, default 65
| 135
trap port, default 65
two-way audio 46
U
upgrading the system 115
uploading to ftp 80, 84
UPnP settings configuration 69
user accounts
adding a user 107
deleting a user 109
modifying a user 108
user accounts, maximum number 107
user name default 37
V
video encoding standard 79
video files, downloading 104
video loss alarm configuration 88
video parameters, configuring 50
video quality 78
video settings configuration 77
video standard
default 51
video type 78
video-in connectors 28, 30, 32
viewing
device name 112
device number 112
encoding version 112
firmware version 112
model 112
number of alarm inputs 112
number of alarm outputs 112
number of channels 112
number of HDDs 112
serial number 112
viewing device information 112
W
warnings 15
warranty 17
web browser
supported 42
WEEE 16
800-15877V1 - A - 10/2013
136 | HVE Encoders User Guide
www.honeywell.com/security
Honeywell Security Products Americas (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywell.com/security
 +1 800 323 4576
Honeywell Security Europe/South Africa
Aston Fields Road, Whitehouse Industrial Estate
Runcorn, WA7 3DL, United Kingdom
www.honeywell.com/security/uk
 +44 (0) 1928 754 028
Honeywell Security Products Americas
Caribbean/Latin America
9315 NW 112th Ave.
Miami, FL 33178, USA
www.honeywell.com/security/clar
 +1 305 805 8188
Honeywell Security Pacific
Level 3, 2 Richardson Place
North Ryde, NSW 2113, Australia
www.asia.security.honeywell.com
 +61 2 9353 7000
Honeywell Security Asia
35F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
 +86 21 5257 4568
Honeywell Security Middle East/N. Africa
Emaar Business Park, Sheikh Zayed Road
Building No. 2, Office No. 30
Post Office Box 232362
Dubai, United Arab Emirates
www.honeywell.com/security/me
 +971 (0) 4 450 5800
Honeywell Security Northern Europe
Ampèrestraat 41
1446 TR Purmerend, The Netherlands
www.honeywell.com/security/nl
 +31 (0) 299 410 200
Honeywell Security Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.honeywell.com/security/de
 +49 (0) 7431 801-0
Honeywell Security France
Immeuble Lavoisier
Parc de Haute Technologie
3-7 rue Georges Besse
92160 Antony, France
www.honeywell.com/security/fr
 +33 (0) 1 40 96 20 50
Honeywell Security Italia SpA
Via della Resistenza 53/59
20090 Buccinasco
Milan, Italy
www.honeywell.com/security/it
 +39 (0) 2 4888 051
Honeywell Security España
Avenida de Italia, n° 7, 2a planta
C.T. Coslada
28821 Coslada, Madrid, Spain
www.honeywell.com/security/es
 +34 902 667 800
www.honeywell.com/security
+1 800 323 4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-15877V1 – Rev A – 10/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change
without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Download PDF