User’s Guide for Model No. IAHBT45 v1322-01
FCC Warnings
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings and Precautions
• Lithium batteries, like all rechargeable batteries, are recyclable and should be recycled or disposed of in normal household waste. Contact your local
government for disposal or recycling practices in your area. They should never be incinerated since they might explode.
• To avoid hearing damage, make sure that the volume on your music player is turned down before connecting your headphones. After placing headphones in
/ on your ears, gradually turn up the volume until you reach a comfortable listening level.
Features & Controls
Supports Bluetooth
Wireless range: 33 feet
Built-in microphone
Micro-USB port for battery recharge
Aux in (3.5mm audio input)
Adjustable headband
On-ear touch controls
DC battery power: built-in
rechargeable lithium ion battery
• Battery life: approx. 8 hours
• Micro-USB to USB cable
• 3.5mm audio cable (Aux In)
• Carry pouch
Use these gestures on the side of the left
earcup to play, pause, skip, and adjust the
Indicator Light
Press and hold to turn
the unit On or Off.
Press and hold for 4 sec.
to turn the unit on and
begin pairing.
Press to play or pause the
current track.
Adjust to turn the volume
up or down.
Tap the center of the earcup to play or pause.
DC Power Input
(3.5mm audio input)
Skip Tracks
Slide your finger left or right to skip
forward or back.
Slide your finger up or down to adjust
the volume.
Headphone Adjustment
Pairing a Bluetooth Device for the First Time
1. Simultaneously power on the unit and begin the pairing process by pressing
and holding the Power/Pair button for approximately 4 seconds.
The indicator will flash red and blue. When pairing, remain within 3 feet
of the unit.
2. Using the native controls on your Bluetooth device, select the IAHB45 in
your Bluetooth settings to pair.
If your device requests a password, enter the default password 0 0 0 0 .
Refer to the user’s manual for your specific device for instructions on pairing
and connecting Bluetooth devices.
After initial pairing, the unit will stay paired unless unpaired manually by the
user or erased due to a reset of the device.
3. If your device should become unpaired or you find it is unable to connect,
repeat the above steps.
Aux In
Using the Aux In Audio Input
Requires a 3.5mm audio cable (included).
1. Connect a 3.5mm audio cable to the AUX IN on the unit and the audio output on an audio device.
2. Use the controls on the connected device to select and play your audio
through the headphones.
Playing Audio Wirelessly
1. To play or pause the selected track, use the native controls on the connected
Bluetooth Device or press the Play/Pause/Volume button.
2. Audio played through the connected Bluetooth device will now be heard
through the headphones. Using the Speakerphone
1. When a call is received, a ringtone will sound through the headphones.
2. Press the Power/Pair button to accept the call or accept the call with the
native controls on the connected device.
3. The incoming call received through the device will now be heard through
the headphones.
4. To end the call, press the Power/Pair button or end the call using the
controls on the connected device. Note: To re-dial the last dialed number, press the Power/Pair key twice.
LED Indicators
Power On
Flashing blue light
Power Off
No light
Solid red light
Charging Complete
Blue light
Flashing red and blue lights
International Support
To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit
the support section at: www.iLiveElectronics.com
Para descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas
frecuentes, visite la sección de apoyo en: www.iLiveElectronics.com
Pour télécharger ce guide de l’utilisateur en anglais, espagnol ou français, ou pour obtenir des réponses à des
questions fréquemment posées, consultez la rubrique d’assistance sur: www.iLiveElectronics.com
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com
Customer Service: 1-888-999-4215 | Email Support: prodinfo@dpiinc.com | Email Parts: partsinfo@dpiinc.com
Copyright © 2015 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property
of their respective owners. Specifications are subject to change without notice.
Download PDF