ebdspir-prm-lv - CP Electronics

Product Guide
EBDSPIR-PRM-LV
Ceiling PIR presence/absence detector 12-24V AC/DC
Overview
The EBDSPIR-PRM-LV PIR (passive infrared) presence
detector provides automatic control of low voltage loads
including lighting and BMS systems with optional manual
control.
Functioning as a presence detector, the unit can turn lights
on when a room is occupied and off when the room is
empty. Optional settings allow lights to be turned off in
response to ambient daylight.
All functionality is fully programmable using an IR handset.
Three variants are available.
EBDSPIR-PRM-LV
Ceiling PIR presence/absence
detector 12-24V AC/DC
EBDSPIR-PRM-LV-GOLD
Ceiling PIR presence/absence
detector 12-24V AC/DC for low
current
EBDSPIR-PRM-LV-OC
Ceiling PIR presence/absence
detector 12-24V AC/DC and open
collector output
Features
PIR Sensor
Detects movement within the unit’s detection range,
allowing load control in response to changes in occupancy.
Front features
Mounting Bezel
IR Receiver
Receives control and programming commands from an
IR (infrared) handset.
Light Level Sensor
Measures the overall light level in the detection area
Sensor Lens
which covers...
PIR Sensor
IR Receiver
Light Level Sensor
Status LEDs
Retaining Spring
Switch Input
Connector
Retaining Spring
Walk Test LED active
when movement is detected
Valid setting received
Power Input & Output Connector
Used to connect power to the unit and to connect a
switched load.
Back features
Power Input &
Output
Connector
Status LEDs
The LED flashes Red to indicate the following:
Switch Input Connector
Two input terminals can be used to manually override the
lights on or off.
Detection diagram
Area of high sensitivity
Area of lower sensitivity
Sensor functionality
Detection Mode
The Detection Mode can be set to behave in Presence or Absence mode:
 Presence When movement is detected the load will automatically turn on. When the area is no longer occupied the
load will automatically switch off after an adjustable time period.
 Absence The load is manually switched on. When the area is no longer occupied the load will automatically switch
off after the adjustable time period has elapsed.
In either case, sensitivity to movement of the PIR sensor can be adjusted using the Sensitivity parameter.
HINT: To assist in setting the Sensitivity, turn on the Walk Test LED which will flash red when movement is detected.
Switch Level On/Off
Occupancy detection can be made dependant on the ambient light level using the Lux On Level and Lux Off Level
parameters.
2
Installation
Choosing a Suitable Location
The EBDSPIR-PRM-LV is designed to be ceiling mounted and must satisfy the following criteria:

Avoid positioning the unit where direct sunlight may enter the sensor element.

Do not site the sensor within 1m of any lighting, forced air heating or ventilation.
 & SWITCH
Do not fix the sensor to an unstable or vibrating surface.
INPUT
CONNECTIONS
Input and switch connections
INPUT & SWITCH
CONNECTIONS
DC Supply
AC Supply
OR 10VAC - 26.5VAC
11.5VDC - 36VDC
+
DC Supply
AC Supply
OR 10VAC - 26.5VAC
11.5VDC - 36VDC
+
COM
OUT
+
MOMENTARY PUSH TO
MAKE SWITCH
COM
OUT
+
Optional for presence,
mandatory for absence detection
MOMENTARY PUSH TO
MAKE SWITCH
Optional for presence,
mandatory for absence detection
LOAD CONNECTIONS
LOAD CONNECTIONS
-PRM-LV
-PRM-LV/OC
-PRM-LV/GOLD
COM
Load
LOAD connections
CONNECTIONS- PRM-LV and PRM-LV-GOLD
LOAD CONNECTIONS
OUT
-PRM-LV
+ LOAD
-PRM-LV/GOLD
LOAD
-PRM-LV/OC
INTERNAL
MOMENTARY PUSH TO
RELAY
MAKE SWITCH
COM
OUT
+COM
Optional for presence,
INTERNAL
mandatory for absence detection
RELAY
LOAD
LOAD
OUT
+
LOAD CONNECTIONS
-PRM-LV/OC
Load connections - PRM-LV-OC
COM
OUT
COM+
INTERNAL OPEN
COLLECTOR
TRANSISTOR
INTERNAL OPEN
COLLECTOR
TRANSISTOR
OUT
+
INTERNAL OPEN
COLLECTOR
TRANSISTOR
LOAD
COM
OUT
+
Absence detection

To use absence detection a retractive (momentary) switch must be connected between the 2 terminals on the
diagram.

The unit ships with presence detection as default. To change to absence detection, press and release the external
switch 5 times within the first minute of power up. The LED will turn on solid for 30 seconds to indicate absence
mode has been selected.

To change back to presence detection, repeat the above procedure—the LED will flash for 30 seconds to indicate
presence mode has been selected.
Note: the above adjustments can also be made using the UHS5 or UNLCDHS handsets. See Programming sections.
Power-up test procedure
When power is applied to the unit, the load will turn on immediately.
Set the timeout to 10 seconds, vacate the room or remain very still and wait for the load to switch off .
Check that the load switches on when movement is detected.
The unit is now ready for programming.
3
Installation
The EBDSPIR-PRM-LV is designed to be mounted using either:

Flush fixing, or

Surface fixing, using the optional Surface Mounting Box (part no. DBB).
Both methods are illustrated below.
Flush Fixing
1
Hole Ø64mm
2
3
4
2
3
4
Warning - be careful
bending springs when
mounting unit.
Surface Fixing
1
50mm or 60mm fixing centres
Pull out spring tab and rotate
spring arm as shown
Wire stripping details
Important
Ensure that the cables are formed as shown
before affixing the cable clamp. The clamp
MUST clamp the outer sheath(s) only.
Bend cores as shown.
Readback function (UNLCDHS handset only)
The UNLCDHS has the ability to read back the settings stored in a device.
To read back individual parameters

Navigate to the parameter and press the ‘R’ (Read) button whilst pointing at the device. The handset will click
when the parameter has been read back, the device will flash its LED, and the value will be shown against the
parameter in the menu.
To read back all of the parameters in a menu

Press and hold the ‘R’ (Read) button for more than 1 second.

The handset will click every time a parameter is received

The device will show multiple flashes of its LED

All of the values will be shown against the parameters in the menu.

The individual parameters may be edited and then saved as a ‘Macro’.
Notes

If a parameter(s) has been missed because of a communication error, the missing value(s) is replaced by dashes.

When reading back, the Channel 1 relay (where fitted) will temporarily be switched off, and will return to it’s
normal state 2 seconds after the read back has been completed.
4
Basic programming
The functionality of the EBDSPIR-PRM-LV is controlled by a number of parameters which
can be changed or programmed by any of the following devices:
 UHS5 Infrared Handset. See below for programmable functions.
 UNLCDHS Infrared Handset (with LCD). See user guide for full programming details.
For most basic programming operations the UHS5 handset can be used and the following procedures
are based on using this device.
Point the handset at the Sensor and send the required programming commands to the unit as shown
below.
Valid commands will be indicated by a red LED flash. See page 1 for details of other LED responses.
Note: other functions on the UHS5 which are not shown below are not applicable to this product.
Number of Shift key presses
Parameter
Name
Default
Value
0
SHIFT 1
1
SHIFT 2
SHIFT 1
2
SHIFT 2
SHIFT 1
3
SHIFT 2
SHIFT 1
UHS5 Handset Graphics
Description
SHIFT 2
Button Activation
On
On
Turn lights on.
Off
Off
Turn lights off.
Walk test
Off
On
Off
Time Out
20 mins
(Time
adjustment)
1, 10 &
20
minutes
5, 15 &
30
minutes
Lux on
level
(Switch
level on)
9
2, 5 & 7
4, 6 & 9
Lux level setting to prevent the luminaires being
switched on if the ambient light level is sufficient
(adjustable between 1 and 9). The luminaires will
always be switched on at level 9.
Lux off
level
(Switch
level off)
9
2, 5 & 7
4, 6 & 9
Lux level setting to switch the luminaires off during
occupancy if the ambient light level goes above
the setting (adjustable between 1 and 9). Level 9
will always keep the lights on. This setting can be
used for “window row switching”.
Note: the Lux Off Level value must always be
greater than the Lux On Level value.
Sensitivity
9
1, 5 & 9
3, 6 & 8
Sensitivity level for detecting movement.
1 = low sensitivity
9 = high sensitivity
Defaults
Presence /
Absence
Shift
When set to On this causes a red LED to flash on
the sensor when it detects movement. Use this
feature to check for adequate sensitivity levels.
10
seconds
D
Presence Presence
Absence
Once the detector is turned on, this value sets
how long the lights will stay on once movement
has ceased.
Returns the unit to the default settings.
Presence mode allows the output to turn on when
movement is detected and off when movement
ceases. Absence mode allows the output to turn
off when movement ceases, but must be manually
turned on first.
Use this button to select the settings in red and
blue signified by the ‘Shift 1’ and ‘Shift 2’ LEDs
Fault finding
What if the load does not turn ON?
 Check that the supply to the circuit is good.
 If the detection range is smaller than expected, check the diagram on page 2. Rotating the sensor slightly may
improve the detection range.
HINT: The Walk Test LED function can be used to check that the unit is detecting movement in the required area.
What if the load does not turn OFF?
 Ensure that the area is left unoccupied for longer than the Time Out Period.
 Ensure that the sensor is not adjacent to circulating air, heaters or lamps.
5
Advanced programming
Parameter Name
Default Value
Range / Options
Description
UHS5
UNLCDHS
Detector Parameters
Walk Test LED
Off
On or Off
When set to On this causes a red LED to flash on the sensor when it detects
movement. Use this feature to check for adequate sensitivity levels.


Time Out
(Time adjustment)
20 minutes
0-99 minutes
Once the detector is turned on, this value sets how long the lights will stay on once
movement has ceased. Select 0 for 10 second delay – use for commissioning only.


Manual Time Out
10 minutes
0-99 minutes
When a manual operation occurs, either via the switch input or the infrared, it
invokes the timeout period.
Example 1: a detector in presence mode has a detector timeout of 15 minutes and
a manual timeout of 3 minutes. When the user leaves the room they press the off
button. The sensor will revert to automatic after 3 minutes, and then walking back
in the room will turn the lights on.
Example 2: using the settings above, the user turns the lights off (say for a
presentation) but stays in the room. Every time a movement is detected, the
manual timeout period is re-triggered, but when it doesn’t pick up for the short
timeout period, the sensor will timeout and revert to automatic. This means the
lights may turn on inadvertently during the presentation, if the occupants are still
for the manual timeout period, so adjust the timing carefully.


Sensitivity On
9
1 (min) to 9 (max)
Sensitivity level for detecting movement when the detector is already on. *UHS5
sets Sensitivity On and Off to the same value.
*

Sensitivity Off
9
1 (min) to 9 (max)
Sensitivity level for detecting movement when the detector is off. *UHS5 sets
Sensitivity On and Off to the same value.
*

Lux time
0
0 (disabled)
1-99 minutes
If the detector measures the lux level and decides that the output needs switching
on or off as a consequence, the lux time must elapse first. If at any time during the
timed delay the lux change reverses then the process is cancelled. Lux Time
enables absence detection to be implemented with a lux off level set. When the
button is pressed, the lights will go on, regardless of ambient light level. However,
if there is sufficient ambient light, they will turn off again after the Lux Time. Note
that whenever the an external switch is pressed, whether in absence or presence
mode, if the lights were out because of the lux level, they will be immediately
turned on again for at least the Lux Time.


Power Up State
On
On or Off
Select No for a 30 second delay on start up. If Yes is selected, there will be no
delay on start up and the detector will always power up detecting.


Inhibit
4 seconds
1 to 999 seconds
When the detector turns off, a delay is instigated to prevent retriggering. In certain
circumstances this delay may not be enough. This parameter allows the delay to
be changed.


Restores factory default settings


Factory default
-
-
Switching functions
Detection Mode
Presence
Presence or
Absence
Presence mode allows the output to turn on when movement is detected and off
when movement ceases. Absence mode allows the output to turn off when
movement ceases, but must be manually turned on first.


Lux on level
(Switch level on)
9
1 to 9
For a higher
resolution a scale
of 101-199 is
available
Sets a minimum light level below which the PIR sensor is enabled, allowing lights
to be turned on by movement.
Note: the Lux Level Off value must always be greater than the Lux Level On value.


Lux off level
(Switch level off)
9
1 to 9
For a higher
resolution a scale
of 101-199 is
available
Sets a maximum light level above which the PIR sensor is disabled, preventing
lights from being turned on by movement.


User Modes
Override On
-
-
If the lights are off, sending the IR command will turn them on immediately and
revert to automatic operation using the manual timeout period .


Override Off
-
-
If the lights are on, sending the IR command will turn them off immediately. After
the manual timeout period (described above), the sensor will revert to automatic.


Cancel
-
-
Cancels the on or off override, returning the detector to normal operation.


-
Short press on, long press off.


-
Short press on, short press off.


Switch Input Modes
1 position switch
together
2 position switch
together
6
Default
-
This page intentionally left blank
7
Technical data
Dimensions
Weight
Supply Voltage
Power consumption
See diagrams opposite
0.15kg
Min 11.5VDC max 36VDC, min
10VAC max 26.5VAC
EBDSPIR-PRM-LV
Low voltage supply with relay
output rating 16A resistive 10A
inductive
EBDSPIR-PRM-LV-GOLD
Low voltage with relay contact for
low on resistance suitable for
control wire applications 3A
resistive load. Not suitable for
inductive loads
EBDSPIR-PRM-LV-OC
Low voltage supply with open
collector output, rating 50mA,
30VDC max
On 640mW, Off 271mW
Terminal Capacity
Temperature
Humidity
Material (casing)
Type
IP rating
2.5mm2
-10ºC to 35ºC
5 to 95% non-condensing
Flame retardant ABS and PC/ABS
Class 2
IP40
Compliance
EMC-2004/108/EC
LVD-2006/95/EC
Load
EBDSPIR-PRM-LV
DBB
Part numbers
Detector
Accessories
Part number
Description
EBDSPIR-PRM-LV
Ceiling PIR presence/absence detector 12-24V AC/DC
EBDSPIR-PRM-LV-GOLD Ceiling PIR presence/absence detector 12-24V AC/DC for low current
EBDSPIR-PRM-LV-OC
Ceiling PIR presence/absence detector 12-24V AC/DC + open collector output
DBB
Surface mounting box
UHS5
Programming IR handset
UNLCDHS
Universal LCD IR handset
IMPORTANT NOTICE!
This device should be installed by a qualified electrician in
accordance with the latest edition of the IEE Wiring
Regulations and any applicable Building Regulations.
FM 45789
EMS 534520
Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice.
8
C.P. Electronics Ltd
Brent Crescent
London
NW10 7XR
United Kingdom
Tel:
+ 44 (0) 333 900 0671
Fax:
+ 44 (0) 333 900 0674
www.cpelectronics.co.uk
enquiry@cpelectronics.co.uk
Ref: #WD495
Issue 1
Download PDF