RS232 RS485 to ethernet convert module user guide USR

Serial to Ethernet module user manual
http://en.usr.cn
Serial to Ethernet module
(USR-TCP232-T, USR-TCP232-2)
(USR-TCP232-S, USR-TCP232-D)
(USR-TCP232-24, USR-TCP232-200)
(USR-TCP232-300, USR-TCP232-442)
File version: V3.2.3
Serial to Ethernet module USR-TCP232-T24 series is data transparent transmission equipment for
convert TCP or UDP socket data to RS232 or RS485 or RS422, small size, low power, powered by ARM
processors, high speed , high Stability.
Key words: TCP/IP, TCP, UDP, RS232, RS485, RS422, Ethernet, Module, Single chip card module,
Serial server, Serial to Ethernet
There is discount for bulk purchase. And customized service is available, MQQ is 300 pics.
Jinan USR IOT Technology Limited provide you Ethernet, WIFI, GPRS Solutions and so on, hardware,
software, and server. Just let me know your needs, we are going to satisfy.
Jinan USR IOT Technology Limited
Page 1 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
Content
Serial to Ethernet module................................................................................................................................................1
1.Product introduction........................................................................................................................................... 4
1.1 Brief Intro.....................................................................................................................................................4
1.2 Function Features......................................................................................................................................4
1.3 Product Characteristics.............................................................................................................................5
1.4 Applications Area....................................................................................................................................... 5
1.5 Product Model............................................................................................................................................ 5
2. Product Test.......................................................................................................................................................... 6
2.1 Hardware Connection............................................................................................................................... 6
2.2 Set-up Software......................................................................................................................................... 7
2.3 Communication Test.................................................................................................................................. 8
2.4 The Default Mode Test.............................................................................................................................. 8
2.5 Virtual COM Test...................................................................................................................................... 11
3. Hardware Description........................................................................................................................................13
3.1 USR-TCP232-S........................................................................................................................................13
3.1.1 Technical Specifications.............................................................................................................. 13
3.1.2 Hardware Description.................................................................................................................. 14
3.1.21 Pin Description....................................................................................................................14
3.1.22 Mechanical Dimensions.................................................................................................... 15
3.1.23 Connection Diagram.......................................................................................................... 15
3.2 USR-TCP232-T........................................................................................................................................17
3.2.1 Technical Specifications.............................................................................................................. 17
3.2.2 Hardware Description.................................................................................................................. 18
3.2.21 Pin description.................................................................................................................... 18
3.2.22 LED Status.......................................................................................................................... 19
3.2.23 Mechanical Dimensions.................................................................................................... 19
3.2.24 Connection Diagram.......................................................................................................... 19
3.3 USR-TCP232-W...................................................................................................................................... 20
3.3.1 Technical Specifications...............................................................................................................21
3.3.2 Hardware Description...................................................................................................................23
3.3.21 Pin description.................................................................................................................... 23
3.3.22 LED Status.......................................................................................................................... 25
3.3.23 Mechanical Dimensions.................................................................................................... 25
3.3.24 Connection Diagram.......................................................................................................... 25
3.4 USR-TCP232-D....................................................................................................................................... 26
3.4.1 Technical Specifications...............................................................................................................26
3.4.2 Hardware Description...................................................................................................................27
3.4.21 Pin Description....................................................................................................................27
3.4.22 LED Status.......................................................................................................................... 27
3.4.23 Mechanical Dimensions.................................................................................................... 28
3.5 USR-TCP232-2........................................................................................................................................ 29
Jinan USR IOT Technology Limited
Page 2 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.5.1 Technical Specifications...............................................................................................................29
3.5.2 Hardware Description...................................................................................................................30
3.5.21 Pin Description....................................................................................................................30
3.5.22 Interface Description.......................................................................................................... 30
3.5.23 Jumper Usage Mechanical Dimensions......................................................................... 31
3.6 USR-TCP232-200....................................................................................................................................32
3.7 USR-TCP232-24......................................................................................................................................32
3.7.1 Technical Specifications...............................................................................................................33
3.7.2 Hardware Description...................................................................................................................33
3.7.21 LED Status.......................................................................................................................... 33
3.7.22 Interface Description.......................................................................................................... 33
3.7.23 Jumper Usage Mechanical Dimensions......................................................................... 35
3.8 USR-TCP232-300....................................................................................................................................36
3.9 USR-TCP232-301....................................................................................................................................36
3.9.1 Technical Specifications...............................................................................................................37
3.9.2 Hardware Description...................................................................................................................37
3.9.21 LED Status.......................................................................................................................... 37
3.9.22 Interface Description.......................................................................................................... 38
3.9.23 Jumper Usage Mechanical Dimensions......................................................................... 39
3.10 USR-TCP232-442................................................................................................................................. 40
3.10.1 Technical Specifications.............................................................................................................40
3.10.2 Hardware Description.................................................................................................................40
3.10.21 LED Status........................................................................................................................ 40
3.10.22 Interface Description........................................................................................................41
3.10.23 Terminal Functional Specifications................................................................................ 42
3.10.24 Jumper Usage Mechanical Dimensions....................................................................... 42
4. Work Mode..........................................................................................................................................................43
4.1 Block Diagram.......................................................................................................................................... 43
4.2 TCP Client Mode......................................................................................................................................43
4.3 UDP Mode.................................................................................................................................................44
4.4 UDP Server Mode....................................................................................................................................44
4.6 Special Functions.....................................................................................................................................46
4.61 RS485................................................................................................................................................46
4.62 Link.................................................................................................................................................. 47
4.63 Reset............................................................................................................................................... 47
4.64 ID...................................................................................................................................................... 47
4.65 Index................................................................................................................................................ 50
4.66 RFC2217.........................................................................................................................................51
5. Application...........................................................................................................................................................52
5.1 COM<->TCP/UDP<->server.................................................................................................................. 52
5.2 Virtual COM.............................................................................................................................................. 53
5.3 COM <-> TCP/UDP <-> COM................................................................................................................54
5.4 Many COM <-> UDP server <-> COM..................................................................................................54
5.5 COM<-> TCP/UDP<->proxy server <->TCP/UDP<->COM...............................................................55
5.6 COM <-> TCP/UDP <-> server.............................................................................................................. 56
Jinan USR IOT Technology Limited
Page 3 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
6. Configuration...................................................................................................................................................... 57
6.1 Configure Command Format................................................................................................................. 57
6.11 Serial Settings Command............................................................................................................. 57
6.12 Network Settings Command........................................................................................................ 58
6.2 USR-TCP232-SETUP............................................................................................................................. 59
6.21 Setup via COM...............................................................................................................................59
6.22 Setup via Net..................................................................................................................................59
7. Contact us........................................................................................................................................................... 61
tion
1.Product introduc
introduction
1.1 Brief Intro
USR-TCP232-T24 series is used to TCP network packet or UDP packet with the micro-controller/
RS232/RS485/RS422 interface data transparent transmission equipment. The product is equipped with ARM
processors, high speed, high stability. Module class of compact size, low power consumption; server refined
aluminum metal shell, compression, anti-drop, anti-interference performance.
USR-TCP232-T24 series is more functional embedded Ethernet serial port data conversion products, it
has built-in TCP/IP protocol stack, the user can use it easily to complete embedded devices network function,
save manpower material resources and development time, make our products faster to market, enhance
competitiveness.
There is 10/100M auto detected RJ45 interface, serial communication baud rate up to 230.4Kbps, can
work at TCP Server, TCP Client, UDP and UDP server mode, setup easily via software.
1.2 Function Features
�
�
�
�
�
�
�
�
�
�
10/100M auto detect interface;
support AUTO MDI/MDIX(Except for TCP232-W, -301), Can use a crossover cable or parallel cable
connection;
RS232 bound rate can set up from 300 to 256000;
RS485 bound rate can set up from 300 to 115200;
Work mode TCP Server, TCP Client, UDP, UDP Server;
Working model related parameters can be set via a serial port or network;
3.3 V and 5 V TTL level compatible (module products);
Virtual serial port supported;
Unique heartbeat package mechanism to ensure that the connection is reliable, put an end to connect
feign death;
Under UDP mode, Packet Broadcast is prohibited, with stronger anti-interference ability;
Jinan USR IOT Technology Limited
Page 4 of 62
tec@usr.cn
Serial to Ethernet module user manual
�
�
�
http://en.usr.cn
across the gateway, across switches, routers;
Can work in LAN, also can work on the Internet (external network);
Transmission distance: RS232 - 15 meters, RS485 - 1000 meters, cable 200 meters (after the switches
together through the Internet, no distance limit).
1.3 Product Characteristics
�
�
�
�
�
�
�
�
32 bits ARM CPU inside;
LAN : 10/100Mbps; protect: Built-2KV isolated electromagnetic;
serial port baud rate: from 2400 to 256 KBPS can be set up, and up to 3 MBPS;
network protocol: ETHERNET ARP IP UDP TCP ICMP;
Software tool: configuration software, TCP/UDP test soft, RS232 debug soft;
Configuration method: RS232 or via Ethernet, free software available;
Operating temperature: -25~75°C;
Storage environment: -40~85°C, 5~95%RH.
1.4 Applications Area
Serial device server module for connecting serial industrial automation equipment such as PLC, sensors,
meters, motors, drives, bar code readers and displays and design.
Serial server module is widely used in attendance, access control systems, Canteen machines, POS
systems, building control, fire control, the banking system, engine room monitoring, UPS monitoring, power,
oil, environmental monitoring, industrial applications and other areas.
T24 Series products are suitable for internal LAN users in a simple to use, for complex network
environments such as the Internet, a camera, a large group networks, fiber to Ethernet, etc., it is
recommended to use E45 series.
1.5 Product Mode
Modell
Model number
Power supply
DC
Interface
Network port
10/100Mbps
Package Type
(Module products
products))
USR-TCP232-S
3.3V
TTL
PHY chip network
interface
Stamp Hole
Package
USR-TCP232-T
5V/3.3V
TTL
Take 2kv magnetic
isolation RJ45
Pin package
package)
Pin package
(DIP package)
USR-TCP232-D
5V/3.3V
TTL
With 1.5KV PHY signal
of electromagnetic
separation
USR-TCP232-2
5V power
adapter/terminal
RS232
Take 2 kv magnetic
isolation RJ45
USR-TCP232-200
5V power
adapter/terminal
RS232
Take 2 kv magnetic
isolation RJ45
Jinan USR IOT Technology Limited
Page 5 of 62
(DIP
tec@usr.cn
Serial to Ethernet module user manual
USR-TCP232-24
5V power
adapter/terminal
RS232/
RS485
Take 2 kv magnetic
isolation RJ45
USR-TCP232-300
5V power
adapter/terminal
RS232/
RS485
Take 2 kv magnetic
isolation RJ45
USR-TCP232-442
5V power
adapter/terminal
RS485/
RS422
Take 2 kv magnetic
isolation RJ45
http://en.usr.cn
Model Description: USR stands for Jinan USR IOT Technology Limited as well as our brand. TCP232 is
TCPIP to serial module product, 2/4/T means serial-side level in the form.
2. Product Test
Pls connect the product with your computer or router to test its performance.
2.1 Hardware Connection
USR-TCP232-S, USR-TCP232-T, USR-TCP232-D are named as the module, USR-TCP232-2,
USR-TCP232-200, USR-TCP232-24, USR-TCP232-300, USR-TCP232-442, the serial server in the
following:
1. Power Supply:
The module’s VDD is DC5V, and its VCC is DC3V3. Only choose one to ensure supply current more than
200mA. The serial server needs matching adapter for power.
2. Serial Connection:
The module’ serial level is TTL. It needs converter TTL to RS232 if connected to RS232 serial of
computer. ( The module can direct to computer with our evaluation kit.)
The serial server can connect to computer directly.( RS485 level needs to convent to RS232).
3. Network Connection:
Connect to computer or join your router via cable. The product can realize automatic switch between
connected directly cable and crossover.
USR-TCP232-T connected to computer as below:
Jinan USR IOT Technology Limited
Page 6 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
2.2 Set-up Software
Set-up Software in the CD as
can help to view default setting then set the
parameter.
1. Setup via net ( Firstly, ensure the computer IP is static. The module IP is 192.168.0.201by default;
Disable firewall, antivirus program and WIFI).
Set via COM ( Connect CFG pin).
Jinan USR IOT Technology Limited
Page 7 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
2.3 Communication Test
in CD can help you test.
Serial to net debugging tester application:
1. Ensure the COM port baud rate, check bits, data bits, stop bit correspond to module parameters.
2. Ensure network protocol, IP address, port number correspond to module parameters.
3. Open COM and the web then connect. They begin transparent transmission after choose the module
IP.
2.4 The Default Mode Test
The default mode is TCP Client, and the default parameter is as below:
IP address: 192.168.0.7
Checksum: 255.255.255.0
Gateway: 192.168.0.201
Baud rate: 115200
Destination IP: 192.168.0.201
Destination port: 8234
Jinan USR IOT Technology Limited
Page 8 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
1. Material: pc with rs232( or use USB to rs232 cable), 3.3V or 5V power, rs232 cable, Network Cable,
COM debug software, TCPIP debug software(in CD, also can be download).
2. Connection: Connect module rs232 to pc rs232, RJ45 to pc RJ45 or the same router (same subnet).
Power on the module.
Note: TXD to RXD, RXD to TXD.
3. Setup PC IP to 192.168.0.201.
4. Open the
Jinan USR IOT Technology Limited
in CD, TCP server, listen port 8234
Page 9 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5. Set the baud rate 115200 and right port, then open COM port.
Jinan USR IOT Technology Limited
Page 10 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
6. The module can connect the port automatically regarding to TCP Client mode. Quickly, you see that ,
then Choose the peers, type info and click send. The info will be sent to the module then output from the
COM.
7. You can send data between two softwares.
Serial to PC: PC Serial->Module Serial->Module Network->PC Network
Network to Serial: PC Network->Module Network->Module Serial->PC Serial
2.5 Virtual COM Test
Virtual COM means to convent data TCP connected to data of a COM within PC for transparent
transmission. Take TCP Client mode for example:
1. Connect module to PC serial and set PC IP to be 192.168.0.201.
2. Install
and run
问题
Add virtual COM, you need to notice COM port, bond rate and work mode of PC, then click Activate.
Jinan USR IOT Technology Limited
Page 11 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5. After Activate click, COM2, will be created, it receives data from TCPIP socket. And data sent to COM2
is transmitted to TCP232 converter then output through RS232.
The success picture as follow:
At this point, you can use your equipment as an ordinary serial port, and operate of local virtual serial
port will converted to operation of the remote module RS232. The figure is show send data between the two
serial port.
Jinan USR IOT Technology Limited
Page 12 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3. Hardware Description
3.1 USR-TCP232-S
USR-TCP232-S Model Stamp Hole Package TTL serial port level, the PHY signal, the small size of the
TCPIP serial protocol module.
3.1.1 Technical Specifications
Major characteristic
Parameter
Package Type
Stamp hole encapsulation (SMD encapsulation)
Schematic diagram
and PCB library
See the CD library file
Power Supply
VCC: 3.3 V DC typical values, minimum 3.15, the biggest 3.45 V,
suitable for 3.3 V microcontroller system
Serial port level
TTL level
Network interface
PHY signal
Physical Size:
PCB size: 33*20mm(L*W)
Temperature and
humidity range
Operating temperature: -25 to 75 ° C
Storage temperature: -40 to 80 ° C
Storage humidity: 5% to 95% RH
Jinan USR IOT Technology Limited
Page 13 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.1.2 Hardware Description
3.1.21 Pin Description
No.
1
Pin
Function
Descriptions
GND
Signal ground
GND
Pin received 200ms low to reset the whole module.
If you do not use, can be suspended.
2
3
RST
ISP
RESET
Update pin
Note: The module is powered automatic reset, it is
recommended that connect the MCU IO port, reset the MCU
control module in a particular case.
This pin to ground to the module power module can be
upgraded.
If you do not use, can be suspended.
4
RXD
5
TXD
6
CFG
Module data is
received
Data receiving end of the module, TTL level 5V or 3.3V
microcontroller
Module data
transmission
Data transmission end of the module, TTL level can be
connected to 5V or 3.3V microcontroller
Low, you can use the serial port module configuration.
Serial ports
Normal working hours left floating or tied HIGH.
Configuration pins
Note: give the power module, and then pulled down the CFG
pin to enter the serial configuration state.
7
LD2
Network data
instructions
Network data indicator LED connected to VCC, without the
current limiting resistance (module existing)
8
LD1
Network connection
status indicator
Network connection status indicator LED connected to VCC,
without the current limiting resistor (module already)
9
2V5
PHY chip
Output voltage
PHY chip to control the voltage output, access networks
transformer center tap
10
RX+
Received signal +
Receive Data+
11
RX-
Received signal -
Receive Data-
12
TX+
Transceiver Data+
Transceiver Data+
13
TX-
Transceiver Data-
Transceiver Data-
14
RTS
the alternate pin
Can be used as RS485 enable pin
15
CTS
the alternate pin
Can be used as a network connection status indicator pin
16
VCC
Power supply
Power supply: 3.3V @ 200mA
Jinan USR IOT Technology Limited
Page 14 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.1.22 Mechanical Dimensions
Unit: mm
3.1.23 Connection Diagram
Jinan USR IOT Technology Limited
Page 15 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
USR-TCP232-S+RJ45 of built-in network transformer:
USR-TCP232-S+RJ45 of built-in network transformer:
Jinan USR IOT Technology Limited
Page 16 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.2 USR-TCP232-T
USR-TCP232-T Model pin package, TTL serial port
level, of 2KV electromagnetic isolation RJ45 interface, small
size TCPIP serial protocol module.
3.2.1 Technical Specifications
Major characteristic
Parameter
Package Type
Pin type package (DIP package)
Schematic diagram and
PCB library
See the CD library file
Power Supply
The module adopts double power supply interfaces, either is ok.
VCC: 3.3 V DC typical values, minimum 3.15, the biggest 3.45 V,
suitable for 3.3 V microcontroller system
VDD: 5 V DC typical values, minimum 4.5, the biggest 5.5 V,
suitable for 5 V microcontroller system
Working current
150 mA, the maximum 200 mA
Serial port level
TTL level
Network interface
PHY signal
Physical Size:
PCB size: 50.5*22.6mm(L*W)
Module size: 55*23*23mm(L*W*H)
Temperature and
humidity range
Operating temperature: -25 to 75 ° C
Storage temperature: -40 to 80 ° C
Storage humidity: 5% to 95% RH
Jinan USR IOT Technology Limited
Page 17 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.2.2 Hardware Description
3.2.21 Pin description
Pin
Name
Description
VDD
Power 1
4.5~5.5V
VCC
Power 2
3.3V
GND
GND
Power and Communications Ground
RST
Reset pin
200ms GND reset the module
TXD
UART transmission pin
5v tolerance
RXD
UART receive pin
5v tolerance
CFG
Configure pin
Configure mode when this pin GND, normal
mode when VCC or idle
Module in the upper left four spare pins from
right to left:
Pin
Name
Description
1: EN
EN alternate pin
RS485 enable pin
2: LINK
LINK alternate pin
Network connectivity status indicator pin
3: ISP
Update pin
This pin to ground to the module power
module can be upgraded.
Jinan USR IOT Technology Limited
Page 18 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.2.22 LED Status
There are two leds in RJ45 connector, one is green, and the other is yellow.
LED
Name
Description
Green
Link state
Light when 100Mbps network linked
Yellow
Data transfer
Blink when there is data in or out
3.2.23 Mechanical Dimensions
Unit: mm
3.2.24 Connection Diagram
MCU
GND
TXD
RXD
5 1 ,A V R ,P I C ,A R M
GND
RXD
TXD
U S R -T C P 2 3 2 -T
R S 2 3 2 to Ethernet
CCV
Jinan USR IOT Technology Limited
Tx+
TxR x+
R x-
1
2
3
6
CCV
Page 19 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
W
3.3 USR-TCP232USR-TCP232-W
USR-TCP232-T Model pin package, TTL serial port level, of 2KV electromagnetic isolation RJ45
interface, small size TCPIP serial protocol module.
Size of -W is fully compatible to -T, except one place(add one more pin), shown below
Jinan USR IOT Technology Limited
Page 20 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.1 Technical Specifications
3.
3.3
Major characteristic
Parameter
Package Type
Pin type package (DIP package)
Schematic diagram and
PCB library
See the CD library file
Power Supply
The module adopts double power supply interfaces, either is ok.
VCC: 3.3 V DC typical values, minimum 3.15, the biggest 3.45 V,
suitable for 3.3 V microcontroller system
VDD: 5 V DC typical values, minimum 4.5, the biggest 5.5 V,
suitable for 5 V microcontroller system
Working current
Around 140 mA when working fullspeed, the maximum 200 mA
Serial port level
TTL level
Network interface
PHY signal
Physical Size:
PCB size: 50.5*22.6mm(L*W)
Module size: 55*23*23mm(L*W*H)
Temperature and
humidity range
Operating temperature: -45 to 85 ° C
Storage temperature: -40 to 85 ° C
Jinan USR IOT Technology Limited
Page 21 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
Storage humidity: 5% to 95% RH
Jinan USR IOT Technology Limited
Page 22 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.2 Hardware Description
3.
3.3
3.21 Pin description
3.
3.3
Pin
Name
Description
VDD
Power 1
4.5~5.5V
VCC
Power 2
3.3V
GND
GND
Power and Communications Ground
RST
Reset pin
200ms GND reset the module
TXD
UART transmission pin
5v tolerance
RXD
UART receive pin
5v tolerance
CFG
Configure pin
Configure mode when this pin GND, normal
mode when VCC or idle
Pin
Jinan USR IOT Technology Limited
Name
Description
Page 23 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
1: EN
EN alternate pin
RS485 enable pin
2: LINK
LINK alternate pin
Network connectivity status indicator pin
3: ISP
Update pin
This pin to ground to the module power
module can be upgraded.
Jinan USR IOT Technology Limited
Page 24 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.22 LED Status
3.
3.3
There are two leds in RJ45 connector, one is green, and the other is yellow.
LED
Name
Description
Green
Link state
Light when 100Mbps network linked
Yellow
Data transfer
Blink when there is data in or out
3.
23 Mechanical Dimensions
3.
3.3.
3.23
Unit: mm
3.24 Connection Diagram
3.
3.3
MCU
GND
TXD
RXD
5 1 ,A V R ,P I C ,A R M
GND
RXD
TXD
U S R -T C P 2 3 2 -T
R S 2 3 2 to Ethernet
CCV
Jinan USR IOT Technology Limited
Tx+
TxR x+
R x-
1
2
3
6
CCV
Page 25 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
3.4 USR-TCP232-D
USR-TCP232-D models to pin package, TTL serial port level,
1.5KV electromagnetic isolation PHY signal, small size, TCPIP
compatible weeks meritorious product serial protocol module.
4.1 Technical Specifications
3.
3.4
Major characteristic
Parameter
Package Type
Pin type package (DIP package)
Schematic diagram and
PCB library
See the CD library file
Power Supply
The module adopts double power supply interfaces, either is ok.
VCC: 3.3 V DC typical values, minimum 3.15, the biggest 3.45 V,
suitable for 3.3 V microcontroller system
VDD: 5 V DC typical values, minimum 4.5, the biggest 5.5 V,
suitable for 5 V microcontroller system
Serial port level
TTL level
Network interface
PHY signal with 1.5KV Ethernet signal
Characteristic
Pin compatible ZLG products
Physical Size:
PCB size: 44*32mm(L*W)
Module size: 44*32*15.4mm(L*W*H)
Temperature and
humidity range
Operating temperature: -25 to 75 ° C
Storage temperature: -40 to 80 ° C
Storage humidity: 5% to 95% RH
Jinan USR IOT Technology Limited
Page 26 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
4.2 Hardware Description
3.
3.4
4.21 Pin Description
3.
3.4
Pin
Name
Description
Pin
Name
Description
1
TX+
Transceiver Data+
2
TX-
Transceiver Data-
23
NC
3
RX+
To RJ45 Pin3
22
NC
4
RX-
To RJ45 Pin6
21
NC
5
Data_LED
Link to yellow Led and 20
through a resistance to
VCC
NC
6
TXD
Transmit data
19
NC
7
RXD
Receive data
18
ISP
8
RTS
RS485 enable pin
17
NC
9
CFG
Config enable port for 16
RS232 Config
3.3V
DC3.3V input and5V use
1 is ok.
10
RST
Reset pin, 200ms low 15
for reset
LINK
Link to green Led and
Through a resistance to
VCC
11
GND
To GND
14
5V
DC5V input@200mA
12
GND
To GND
13
5V
DC5V input@200mA
A breach here
For Update
3.
4.22 LED Status
3.4
USR-TCP232-D Red LED, If the indicator is energized, the module power input is correct.
Jinan USR IOT Technology Limited
Page 27 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
4.23 Mechanical Dimensions
3.
3.4
Unit: mm
3.
4.24 Connection Diagram
3.4
Note: Isolation transformer has been on this module, so you need not to add Isolation transformer in
your RJ45 port.
Jinan USR IOT Technology Limited
Page 28 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5 USR-TCP232-2
3.
3.5
USR-TCP232-2 Model is RS232 level, 2KV electromagnetic isolation RJ45 connector, 5.5 * 2.1 standard
power supply or terminal power supply serial server.
5.1 Technical Specifications
3.
3.5
Major characteristic
Parameter
Power Supply
DC5V@1A power adapter
Serial port level
RS232
Network interface
RJ45 ports with 2KV electromagnetic isolation
Physical Size:
PCB size: 67.3*34mm(L*W)
Product size: 86.6×34×25mm(L*W*H)
Temperature and
humidity range
Operating temperature: -25 to 75 ° C
Storage temperature: -40 to 80 ° C
Storage humidity: 5% to 95% RH
Jinan USR IOT Technology Limited
Page 29 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5.2 Hardware Description
3.
3.5
5.21 Pin Description
3.
3.5
There are two leds in RJ45 connector, one is green, and the other is yellow. And 1 power led.
LED
Name
Description
Red
Power
Light When Power on
Green
Link state
Light when 100Mbps network linked
Yellow
Data transfer
Blink when there is data in or out
5.22 Interface Description
3.
3.5
Power Interface
DC5V power supply, you can make 5.5 * 2.1 standard power supply or 3.81mm pitch terminal blocks, the
default state is 5.5 * 2.1 standard power supply, power input with TVS protection products.
RS232 Interface
TXD
RXD
GND
RS232 use 9 pin female (hole), only 3 pins in use, others are NC, the detail is below.
5 4 3 2 1
9 8 7 6
ID
Mark
2
TXD
Send Device Data
RS232 Level
3
RXD
Receive Device Data
RS232 Level
5
GND
Ground
Communication total site
9
VCC
Device is powered via this pin
Jinan USR IOT Technology Limited
Function
Page 30 of 62
Description
The PCB pads jumper need it
with the power input a positive
connection for the serial
sensor supply via the serial
line or external power to the
device is not turned on by
default.
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
RJ45 Internet Interface
Auto detected 10M/100M RJ45 interface, support AUTO MDI/MDIX, that is to say you can use crossover
cable or a straight cable to connect it to PC for test.
Pin
Name
Description
1
TX+
Transceiver Data+
2
TX-
Transceiver Data-
3
RX+
Receive Data+
4
n/c
Not connected
5
n/c
Not connected
6
RX-
Receive Data-
7
n/c
Not connected
8
n/c
Not connected
5.23 Jumper Usage Mechanical Dimensions
3.
3.5
Mini Jumper Marks:
Short CFG and GND is CFG, effective, using serial for configuration.
Short UPD and GND is UPD, effective, coming to upgrade.
Mini Jumper links to GND by default, not effective.
Link,EN function, pls refer to 4.6 Special functions Description.
Jinan USR IOT Technology Limited
Page 31 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
6 USR-TCP232-200
3.
3.6
USR-TCP232-200 Model RS232 level, the 2KV electromagnetic isolation RJ45 interface, 5.5 * 2.1
standard power supply or terminal power supply serial server.
7 USR-TCP232-24
3.
3.7
USR - TCP232-24 models for RS232 or RS485 level, 2 kv RJ45 interface of electromagnetic isolation,
5.5 * 2.1 standard power supply serial server.
Jinan USR IOT Technology Limited
Page 32 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
7.1 Technical Specifications
3.
3.7
Major characteristic
Parameter
Power Supply
DC5V@1A power adapter
Serial port level
RS232
RS485
Network interface
RJ45 ports with 2KV electromagnetic isolation
Physical Size:
PCB size: 80*50mm(L*W)
Product size: 89.2×50×23mm(L*W*H)
Temperature and
humidity range
Operating temperature: -25 to 75 ° C
Storage temperature: -40 to 80 ° C
Storage humidity: 5% to 95% RH
3.
7.2 Hardware Description
3.7
7.21 LED Status
3.
3.7
There are two leds in RJ45 connector, one is green, and the other is yellow. And 1 power led.
LED
Name
Description
Green
Power
Light When Power on
Green
Link state
Light when 100Mbps network linked
Yellow
Data transfer
Blink when there is data in or out
7.22 Interface Description
3.
3.7
Power interface
DC5V power supply, you can make 5.5 * 2.1 standard power supply, power input with TVS protection
products.
RS232 interface
RS232 use 9 pin female (hole), only 3 pins in use, others are NC, the detail is below.
Jinan USR IOT Technology Limited
Page 33 of 62
tec@usr.cn
http://en.usr.cn
TXD
RXD
GND
Serial to Ethernet module user manual
5 4 3 2 1
9 8 7 6
ID
Mark
Function
Description
2
TXD
Send Device Data
RS232 Level
3
RXD
Receive Device Data
RS232 Level
5
GND
Ground
Communication total site
9
VCC
Device is powered via this pin
The PCB pads jumper need it
with the power input a positive
connection for the serial
sensor supply via the serial
line or external power to the
device is not turned on by
default.
RS485 interface
RS485 has two lines A(data+) and B(data-), 120 Ohms Termination Resistance on board.
No
Notte:
RS232 and RS485 can not work together, since it is 1 channel.
this module can autoselect for RS232 or RS485, doesn't need choose via jumper(from hardware version
V3.0)
RJ45 internet interface
Auto detected 10M/100M RJ45 interface, support AUTO MDI/MDIX, that is to say you can use crossover
cable or a straight cable to connect it to PC for test.
Pin
Name
Description
1
TX+
Transceiver Data+
2
TX-
Transceiver Data-
3
RX+
Receive Data+
4
n/c
Not connected
5
n/c
Not connected
6
RX-
Receive Data-
7
n/c
Not connected
8
n/c
Not connected
Jinan USR IOT Technology Limited
Page 34 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
7.23 Jumper Usage Mechanical Dimensions
3.
3.7
Mini Jumper Marks:
Short CFG and GND is CFG, effective, using serial for configuration.
Short UPD and GND is UPD, effective, coming to upgrade.
Mini Jumper links to GND by default, not effective.
Jinan USR IOT Technology Limited
Page 35 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
8 USR-TCP232-300
3.
3.8
USR-TCP232-300 model products for RS232 or RS485 level, 2 kv RJ45 interface of electromagnetic
isolation, 5.5 * 2.1 standard power supply with a shell of a serial port server.
USR-TCP232-300 by USR-TCP232-24 shell, its specification please see USR-TCP232-24.
3.
9 USR-TCP232301
3.9
USR-TCP232-301
USR - TCP232-24 models for RS232 or RS485 level, 2 kv RJ45 interface of electromagnetic isolation,
5.5 * 2.1 standard power supply serial server.
The one with case, named as TCP232-301, footprint is fully compatible with TCP232-300
The one withour case, named as TCP232-301M, footprint is fully compatible with TCP232-24
Jinan USR IOT Technology Limited
Page 36 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
9.1 Technical Specifications
3.
3.9
Major characteristic
Parameter
Power Supply
DC5V@1A power adapter
Serial port level
RS232
RS485
Network interface
RJ45 ports with 2KV electromagnetic isolation
Physical Size:
PCB size: 80*50mm(L*W)
Product size: 89.2×50×23mm(L*W*H)
Temperature and
humidity range
Operating temperature: -45 to 85 ° C
Storage temperature: -45 to 85 ° C
Storage humidity: 5% to 95% RH
9.2 Hardware Description
3.
3.9
9.21 LED Status
3.
3.9
There are two leds in RJ45 connector, one is green, and the other is yellow. And 1 power led.
LED
Name
Jinan USR IOT Technology Limited
Description
Page 37 of 62
tec@usr.cn
Serial to Ethernet module user manual
Green
Power
Light When Power on
Green
Link state
Light when 100Mbps network linked
Yellow
Data transfer
Blink when there is data in or out
http://en.usr.cn
9.22 Interface Description
3.
3.9
Power interface
DC5V power supply, you can make 5.5 * 2.1 standard power supply, power input with TVS protection
products.
TXD
RXD
GND
RS232 interface
RS232 use 9 pin female (hole), only 3 pins in use, others are NC, the detail is below.
5 4 3 2 1
9 8 7 6
ID
Mark
Function
Description
2
TXD
Send Device Data
RS232 Level
3
RXD
Receive Device Data
RS232 Level
5
GND
Ground
Communication total site
9
VCC
Device is powered via this pin
The PCB pads jumper need it
with the power input a positive
connection for the serial
sensor supply via the serial
line or external power to the
device is not turned on by
default.
RS485 interface
RS485 has two lines A(data+) and B(data-), 120 Ohms Termination Resistance on board.
No
Notte: this module user Jumpers to change work for RS232 or RS485, by default it work at RS232 mode.
RJ45 internet interface
Auto detected 10M/100M RJ45 interface, doesn't support AUTO MDI/MDIX.
Pin
Jinan USR IOT Technology Limited
Name
Description
Page 38 of 62
tec@usr.cn
Serial to Ethernet module user manual
1
TX+
Transceiver Data+
2
TX-
Transceiver Data-
3
RX+
Receive Data+
4
n/c
Not connected
5
n/c
Not connected
6
RX-
Receive Data-
7
n/c
Not connected
8
n/c
Not connected
http://en.usr.cn
9.23 Jumper Usage Mechanical Dimensions
3.
3.9
Mini Jumper Marks:
Short CFG and GND is CFG, effective, using serial for configuration.
Short UPD and GND is UPD, effective, coming to upgrade.
Mini Jumper links to GND by default, not effective.
Jinan USR IOT Technology Limited
Page 39 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
10 USR-TCP232-442
3.
3.10
USR-TCP232-442 model products for RS485 or RS422 level, 2 kv RJ45 interface of electromagnetic
isolation, 5.5 * 2.1 standard power supply or power supply terminal of a serial port server with shell.
10
.1 Technical Specifications
3.
3.10
10.1
Major characteristic
Parameter
Power Supply
DC5-18Vpower adapter
Serial port level
RS485
RS422
Network interface
RJ45 ports with 2KV electromagnetic isolation
Physical Size:
PCB size: 80*50mm(L*W)
Product size: 95*85*25mm(L*W*H)
Temperature and
humidity range
Operating temperature: -25 to 75 ° C
Storage temperature: -40 to 80 ° C
Storage humidity: 5% to 95% RH
10
.2 Hardware Description
3.
3.10
10.2
10
.21 LED Status
3.
3.10
10.21
There are two leds in RJ45 connector, one is green, and the other is yellow. And 1 power led.
Jinan USR IOT Technology Limited
Page 40 of 62
tec@usr.cn
Serial to Ethernet module user manual
LED
Name
http://en.usr.cn
Description
Red
Power
Light When Power on
Green
Link state
Light when 100Mbps network linked
Yellow
Data transfer
Blink when there is data in or out
10
.22 Interface Description
3.
3.10
10.22
Power interface
DC5V power supply, you can make 5.5 * 2.1 standard power supply and 3.81mm pitch terminal blocks,
power input with TVS protection products.
485 interface
RS
RS485
RS485 has two lines A(data+) and B(data-),the signal terminal 0.5A PTC Resettable Fuse, to prevent
accidental high current burn out the motherboard; Professional TVS lightning protection circuit design;
Internal 120R terminal matching resistor (the default is not used, the available short cap configured to use);
Can allow up to 32 transceiver node connected to the bus.
422 interface
RS
RS422
RS422 lead wires are respectively A (RX +), B (RX-), Y (TX +), Z (TX) G (GND). Signal end has
characteristics of superheated tube, can prevent the output short circuit; Can allow up to 256 transceiver
node connected to the bus.
Notice: RS485 and RS422 cannot be used at the same time, by default it work at RS485 mode
RJ45 internet
Auto detected 10M/100M RJ45 interface, support AUTO MDI/MDIX,that is to say you can use crossover
cable or a straight cable to connect it to PC for test.
Pin
Name
Description
1
TX+
Transceiver Data+
2
TX-
Transceiver Data-
3
RX+
Receive Data+
4
n/c
Not connected
5
n/c
Not connected
6
RX-
Receive Data-
7
n/c
Not connected
8
n/c
Not connected
Jinan USR IOT Technology Limited
Page 41 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
10
.23 Terminal Functional Specifications
3.
3.10
10.23
10
.24 Jumper Usage Mechanical Dimensions
3.
3.10
10.24
Mini Jumper Marks:
1. Short CFG and GND is CFG, effective, using serial for configuration.
Short UPD and GND is UPD, effective, coming to upgrade.
Mini Jumper links to GND by default, not effective.
2. RS485 terminal resistance is not included by default, short Mini Jumper with according pin.
Jinan USR IOT Technology Limited
Page 42 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
4. Work Mode
4.1 Block Diagram
power
Ethernet
TTL
User
device
Serial to Ethernet
Converter
Take USR-TCP232-T for example, show demo application of module USR-TCP232-T
2 TCP Client Mode
4.
4.2
In TCP client mode, after power on module according to their own Settings active TCP server to connect
to the server, and then establish a long connection, data transparent transmission after this mode, the TCP
server IP module would need to be visible and the visible means directly by module's IP can PING the server
IP, server side can be fixed IP, the Internet can also be internal network IP and module in the same local area
network.
1. Module try to connect to server
1.Server listen a TCP port
2. Data transfer through the connection
MCU
5 1 ,A V R ,P I C ,A R M
Ethernet
COM
Module work at TCP Client mode
Jinan USR IOT Technology Limited
Page 43 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
4.3 UDP Mode
In UDP mode, after the module is powered on listening on port Settings, not take the initiative to
establish a connection, when data from by forwarding to the serial port, when a serial port receives the data
sent over the network to the IP and port module Settings.
1. Module listen a UDP port
1.PC listen a UDP port
2. Data transfer With out connection, only data packet
MCU
5 1 ,A V R ,P I C ,A R M
R S 232
Ethernet
Module work at UDP mode
4.4 UDP Server Mode
UDP server refers to the normal UDP are not validated on the basis of the source IP address, destination
IP instead of the UDP packets are received data source IP, similar to TCP server functionality.
In this mode, the module by default record a destination IP, when a serial port data, to record the IP to
send data, at the same time, the module at the server status, to accept the network packets sent to module,
and adjust the target IP IP for the data source, suitable for multiple IP working mode for the module.
Use computer end program and UDP mode is exactly the same, no need to change.
Jinan USR IOT Technology Limited
Page 44 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
1.PC listen a UDP port
1. Module listen a UDP port
2. Data transfer from Module to PC-A
MCU
COM
Ethernet
5 1 ,A V R ,P I C ,A R M
Module work at UDP Server mode
3
Data transfer from Module to PC-B
2
Module change the
target IP to pc
PC-B Send a data to module
1
P C -A
P C -B
Note:
Note:UDP mode, UDP server mode with a single maximum length of 1472 bytes should be controlled at or
below, if greater than this length, the module will automatically restart, the proposed subcontractor sent.
4.5 TCP Server Mode
In TCP Server mode, module and gateway trying to communication first, and then monitor set up local
port, there is connection request response and create a connection, can exist at the same time up to 4 links, a
serial port after receipt of the data will be sent to all at the same time of establishing links with network module
device.
USR-TCP232-SETUP software, set the Index function can be achieved when to establish a
multi-channel connection, the module can identify communications equipment, and with the specified device
to communicate.
Jinan USR IOT Technology Limited
Page 45 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
s
4.6 Special Function
unctions
4.61 RS485
USR-TCP232-S, USR-TCP232-T, USR-TCP232-D products "RTS" Alternate Pin USR-TCP232-200
product "EN" alternate pin for RS485, external enable control pin.
Set the software interface:
Jinan USR IOT Technology Limited
Page 46 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
4.62 Link
The Link pins for the module to establish a communication connection status indicates pin, establish the
communication Link pin will output low level, no connection is established, output high level.
USR-TCP232-S "CTS" Alternate Pin USR-TCP232-T products, USR-TCP232-200 product "Link"
alternate pin, external Link instructions.
Set the software interface:
4.63 Rese
Resett
When the module as a TCP Client-side, the module will take the initiative to connect TCP SERVER.
When the Reset function, the module tries to connect to TCP Server-side 30 times, still unable to establish a
connection, the module will automatically restart.
Set the software interface:
4.64 ID
Module as TCP Client-side ID function for TCP Server-side distinguish between data sources, to achieve
the establishment of the connection or data communication process device ID will also be sent, the module ID
number is set to decimal, range 0 - 65535, requires the receiving end HEX format.
1.Select "Connect" to establish a communication connection, TCP Server-side will receive the
corresponding TCP Client-side ID (ID Description: The first four shows for the ID number, the last four digits
of the display ID negated to authentication).
The following picture shows the module do TCP CLINENT establish a communication connection ID
feature is enabled, the setup interface module ID number 12::
Jinan USR IOT Technology Limited
Page 47 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
The figure below shows establish a communication connection ID function, the device through the serial
communication interface to the TCP Server-side:
2.Select data during each data transfer, TCP Server-side will receive the corresponding TCP Client-side
ID (ID Description: ID before data transmitted only display four-digit ID number).
The following picture shows the module do the TCP CLINENT ID feature is enabled, data transmission
module ID number 12 setting interface:
Jinan USR IOT Technology Limited
Page 48 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
The figure below shows the data communication ID function, the device through the serial port to TCP
Server communication interface:
Jinan USR IOT Technology Limited
Page 49 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
4.65 Index
Module as TCP SERVER end up at the same time to establish four connections, server-side at the same
time send data to four CLIENT and SERVER the receiving Client-side data can not distinguish between
sources of data, the Index function can send and receive data source selection.
Index function is enabled, communication data is displayed corresponding Client side device number,
specific parameters are described below:
1.When receive data from Ethernet, module will send data to serial port with head 49 N ,followed by data.
49 represent incoming data, N represent client index.
2.When user MCU want send data to module serial port, start with head 4F N data... 4F represent send
out, N represent which client.
3.When new TCP connection incoming, module will send 43 N M to serial port, indicating that there is
current link N accessed, total link number M.
4.When link number have exceed maximum, new link requirement will lead to message 46 46.
5.When disconnect, module will send 44 N M, represent current link N is delete, left link M.
Note: The above values set are HEX format.
Set the software interface:
Data transmission as shown below:
Jinan USR IOT Technology Limited
Page 50 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
4.66 RFC2217
RFC2217 is an agreement for setup com port settings via Ethernet by socket, Our product support an
agreement like that, but not standard RFC2217, it is more sample and easy than RFC2217.
1.When module receive setup command, if is a valid command(right packet head and right checksum),
the module will change self setting and answer nothing, else the data bits would be sent out at com port.
2.TCP Client, TCP Server, UDP Client, UDP Server, UDP broadcast support this function.
3.All changes will work at once, but not save to module, when power off will lose the settings.
Set the software interface:
The command length is 8 bits, detail as follow table. The demo bytes are in hex mode:
Name
Packet
header
Band rate
UART bits setting
Check sum
Bytes
3
3
1
1
Description
Three bytes
Band rate in hex
mode, High byte first.
Parity/data/stop
settings, see follow
table.
Check sum of
last 4 bytes
For example
(115200,N,8,1)
55 AA 55
01 C2 00
83
83
For example
(9600,N,8,1)
55 AA 55
00 25 80
83
83
Appendix: UART bits setting detail.
Bit
Description
Value
Description
1:0
Data bits
00
5 bits
01
6 bits
10
7 bits
11
8 bits
0
1 bits
1
2 bits
0
Not enable Parity
1
Enable Parity
00
ODD
01
EVEN
10
Mark
11
Clear
000
Please fill 0
2
3
5:4
8:6
Stop bits
Parity enable
Parity type
Not used
Jinan USR IOT Technology Limited
Page 51 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
Test bits
55AA5501C2008346 For 115200 N,8,1
55AA550025808328 For 9600 N,8,1
Those two data is not transferred to serial, but the packet not conform will be transferred and revealed.
Open this function then open RFC2217 via USR-VCOM so serial port baud rate of PC application
software serial
server device can be matched automatically.
5. Application
5.1 COM<->TCP/UDP<->server
MCU use as RS2 3 2
Socket software on
PC or hand system
n
er
MCU
5 1 ,A V R ,P I C ,A R M
et
h
Et
E t h e r ne
R S 232
t
COM to Ethernet
Jinan USR IOT Technology Limited
Page 52 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5.2 Virtual COM
Install USR-VCOM and make settings.
VSPM run on PC
MCU use as RS2 3 2
计算端通用 R S232操 作
MCU
5 1 ,A V R ,P I C ,A R M
R S 232
Ethernet
Virtual COM mode
MCU
5 1 ,A V R ,P I C ,A R M
R S 232
Old RS 2 3 2 communication system
Jinan USR IOT Technology Limited
Page 53 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5.3 COM <-> TCP/UDP <-> COM
MCU use as RS2 3 2
MCU
5 1 ,A V R ,P I C ,A R M
MCU use as RS2 3 2
Ethernet
R S 232
R S 232
MCU
5 1 ,A V R ,P I C ,A R M
Update to RS 2 3 2
remote Communication
MCU
5 1 ,A V R ,P I C ,A R M
MCU
R S 232
5 1 ,A V R ,P I C ,A R M
O l d Communication
5.4 Many COM <-> UDP server <-> COM
MCU
Module in Server
… …
Module in
Client
MCU
Jinan USR IOT Technology Limited
MCU
MCU
Page 54 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5.5 COM<-> TCP/UDP<->proxy server <->TCP/UDP<->COM
You can use a proxy server to treat the data form one module to other, or just use you MCU to control the
module IP and destination IP Real-time. The method is pull CFG PIN to GND, and send the new configuration
data, then pull CFG pin to VCC to use new settings.
MCU
MCU
MCU
MCU
MCU
MCU
Jinan USR IOT Technology Limited
Page 55 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
5.6 COM <-> TCP/UDP <-> server
Server
Ethernet
Routing / Switch
Ethernet
MCU
MCU
Jinan USR IOT Technology Limited
Ethernet
MCU
MCU
Page 56 of 62
MCU
MCU
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
ation
6. Configur
Configuration
Module's working mode can be set as needed, we try my best to let the user work become simple, all did
not open advanced parameters, if you have special requirements, please contact us.
You can set the work mode, the module IP and port, subnet mask, gateway, serial port baud rate, module
port, destination IP and port,can be set through the serial port or network port are two ways to setup software
(USR-TCP232-Setup).
6.1 Configure Command Format
6.11 Serial Settings Command
Configure mode UART interface: 9600bps,n,8,1
Part
Bytes
prefix
2
destination IP
4
destination
port
2
Host IP
Description
Example
Hex
0x55 0xAA
0x55 0xAA
0x55 0xAA
destination IP
192.168.0.2
01
0xC9 0x00 0xA8 0xC0
Destination port
8234
0x2A 0x20
4
The IP module hold
192.168.0.7
0x07 0x00 0xA8 0xC0
Host port
2
TCP/UDP source port
20108
0x8C 0x4E
Gateway
4
Gateway IP
192.168.0.2
01
0xC9 0x00 0xA8 0xC0
0x01: TCP Client
TCP mode
0x01
Work mode
1
0x00: UDP
0x02: UDP Server
baud rate
3
UART baud rate
115200
0x00 0xC2 0x01
Reserved
1
Reserved
00
0x00
0xB9
checksum
1
Sum(destination
IP, 0xB9
destination port, host IP,
host port, gateway, work
mode,
baud
rate,
reserved)
prefix
2
0x55 0xAA
0x55 0xAA
Jinan USR IOT Technology Limited
0x55 0xAA
Page 57 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
Once in configure mode, the UART parameter change to 9600bps,n,8,1, and a ‘U’ ascii character is send
out to ensure the control MCU that in the configure mode. If the 24byte command has effect, a ‘K’ ascii
character is send back to control MCU. If configure command format error, an ‘E’ character will be send back
to control MCU. If the error is the checksum not match , the 1byte right checksum will be send back to control
MCU also.
6.12 Network Settings Command
Network Settings is fulfilled via UDP Broadcast. No need and must not connect CFG.
UDP settings parameters:
UDP Broadcast Destination Address: 255.255.255.255
UDP Local Port: 1500
UDP Destination Port: 1500
40 bytes packet is broad-casted to the web via UDP when searching for devices. The module with same
WLAN physically respond and return 35 bytes.
Send Settings Command Format:
Name
Length
Description
Example
MAC
6
Set MAC address of module
00 CE 83 25 4D 60
Old Password
6
110415
31 31 30 34 31 35
Parameter
21
c9 00 a8 c0 2a 20
It is same with serial settings excel, 07 00 a8 c0 8c 4e
besides header and check bits.
c9 00 a8 c0 01 00
c2 01 03
Independent
ID
3
ID-H,ID-L,ID-type, 0 for not enable
00 00 00
Subnet Mask
4
The low is ahead, as 255.255.255.0
00 FF FF FF
Configuration
Return Settings Command Format:
Description
Example
6
Set MAC address of module
00 CE 83 25 4D 60
1
Version #, as 4.2 stands for 0x42
42
Parameter
21
It is same with serial settings excel,
besides header and check bits.
C9 00 A8 C0 2A 20
07 00 A8 C0 8C 4E
C9 00 A8 C0 01 00
C2 01 03
Independent
ID
3
ID-H,ID-L,ID-type, 0 for not enable
00 00 00
Subnet Mask
4
The low is ahead, as255.255.255.0
00 FF FF FF
Name
Length
MAC
Status Word
Configuration
Jinan USR IOT Technology Limited
Page 58 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
6.2 USR-TCP232-SETUP
USR - TCP232 - the Setup software
can be extended in functions to specific function module
Settings, as shown in the figure below.
6.21 Setup via COM
In normal working condition, connect CFG pin to enter the serial configuration state, through the network
configuration to be disconnect CFG pin module set through the serial port to receive instruction and to
change the operating parameters.USR-TCP232-Setup software to be modified, as follows:
1.In”use com port for setup”fill in the correct COM number;
2.Click “read via com”,the left side will display the current configuration parameters, can modify the
parameters of the desired Settings;
3. Click “setup via com”,to complete the module configuration;
4. After Setting, disconnect CFG, module begin work.
6.22 Setup via Net
Run USR-TCP232-Setup software then:
1. Click “search in LAN”
2. It reveals modules searched, double click, the left side will display the current configuration
parameters, can modify the parameters of the desired Settings
3. Click “Setup via Net”
4. Module restart automatically
Jinan USR IOT Technology Limited
Page 59 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
6.23 Special Function Configuration
USR - TCP232 - the Setup software can be extended in functions to specific function module Settings, as
shown in the figure below.
Jinan USR IOT Technology Limited
Page 60 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
7. Contact us
Company: Jinan USR IOT Technology Limited
Address: 1-728, Huizhan Guoji Cheng, Gaoxin Qu, Jinan, Shandong, China
Tel: 86-531-55507297
86-531-88826739
Web: http://en.usr.cn
Skype: lisausr
Email: sales@usr.cn
tec@usr.cn
Jinan USR IOT Technology Limited
Page 61 of 62
tec@usr.cn
Serial to Ethernet module user manual
http://en.usr.cn
Revison history
V3.2.2 modify description about RS232 and RS485 selection jumper
V3.2.3 remove Order Info
Jinan USR IOT Technology Limited
Page 62 of 62
tec@usr.cn
Download PDF